linux/drivers/gpu/drm/i915/intel_ddi.c

2774 lines
82 KiB
C
Raw Normal View History

/*
* Copyright © 2012 Intel Corporation
*
* Permission is hereby granted, free of charge, to any person obtaining a
* copy of this software and associated documentation files (the "Software"),
* to deal in the Software without restriction, including without limitation
* the rights to use, copy, modify, merge, publish, distribute, sublicense,
* and/or sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following conditions:
*
* The above copyright notice and this permission notice (including the next
* paragraph) shall be included in all copies or substantial portions of the
* Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
* THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS
* IN THE SOFTWARE.
*
* Authors:
* Eugeni Dodonov <eugeni.dodonov@intel.com>
*
*/
#include "i915_drv.h"
#include "intel_drv.h"
struct ddi_buf_trans {
u32 trans1; /* balance leg enable, de-emph level */
u32 trans2; /* vref sel, vswing */
u8 i_boost; /* SKL: I_boost; valid: 0x0, 0x1, 0x3, 0x7 */
};
static const u8 index_to_dp_signal_levels[] = {
[0] = DP_TRAIN_VOLTAGE_SWING_LEVEL_0 | DP_TRAIN_PRE_EMPH_LEVEL_0,
[1] = DP_TRAIN_VOLTAGE_SWING_LEVEL_0 | DP_TRAIN_PRE_EMPH_LEVEL_1,
[2] = DP_TRAIN_VOLTAGE_SWING_LEVEL_0 | DP_TRAIN_PRE_EMPH_LEVEL_2,
[3] = DP_TRAIN_VOLTAGE_SWING_LEVEL_0 | DP_TRAIN_PRE_EMPH_LEVEL_3,
[4] = DP_TRAIN_VOLTAGE_SWING_LEVEL_1 | DP_TRAIN_PRE_EMPH_LEVEL_0,
[5] = DP_TRAIN_VOLTAGE_SWING_LEVEL_1 | DP_TRAIN_PRE_EMPH_LEVEL_1,
[6] = DP_TRAIN_VOLTAGE_SWING_LEVEL_1 | DP_TRAIN_PRE_EMPH_LEVEL_2,
[7] = DP_TRAIN_VOLTAGE_SWING_LEVEL_2 | DP_TRAIN_PRE_EMPH_LEVEL_0,
[8] = DP_TRAIN_VOLTAGE_SWING_LEVEL_2 | DP_TRAIN_PRE_EMPH_LEVEL_1,
[9] = DP_TRAIN_VOLTAGE_SWING_LEVEL_3 | DP_TRAIN_PRE_EMPH_LEVEL_0,
};
/* HDMI/DVI modes ignore everything but the last 2 items. So we share
* them for both DP and FDI transports, allowing those ports to
* automatically adapt to HDMI connections as well
*/
static const struct ddi_buf_trans hsw_ddi_translations_dp[] = {
{ 0x00FFFFFF, 0x0006000E, 0x0 },
{ 0x00D75FFF, 0x0005000A, 0x0 },
{ 0x00C30FFF, 0x00040006, 0x0 },
{ 0x80AAAFFF, 0x000B0000, 0x0 },
{ 0x00FFFFFF, 0x0005000A, 0x0 },
{ 0x00D75FFF, 0x000C0004, 0x0 },
{ 0x80C30FFF, 0x000B0000, 0x0 },
{ 0x00FFFFFF, 0x00040006, 0x0 },
{ 0x80D75FFF, 0x000B0000, 0x0 },
};
static const struct ddi_buf_trans hsw_ddi_translations_fdi[] = {
{ 0x00FFFFFF, 0x0007000E, 0x0 },
{ 0x00D75FFF, 0x000F000A, 0x0 },
{ 0x00C30FFF, 0x00060006, 0x0 },
{ 0x00AAAFFF, 0x001E0000, 0x0 },
{ 0x00FFFFFF, 0x000F000A, 0x0 },
{ 0x00D75FFF, 0x00160004, 0x0 },
{ 0x00C30FFF, 0x001E0000, 0x0 },
{ 0x00FFFFFF, 0x00060006, 0x0 },
{ 0x00D75FFF, 0x001E0000, 0x0 },
};
static const struct ddi_buf_trans hsw_ddi_translations_hdmi[] = {
/* Idx NT mV d T mV d db */
{ 0x00FFFFFF, 0x0006000E, 0x0 },/* 0: 400 400 0 */
{ 0x00E79FFF, 0x000E000C, 0x0 },/* 1: 400 500 2 */
{ 0x00D75FFF, 0x0005000A, 0x0 },/* 2: 400 600 3.5 */
{ 0x00FFFFFF, 0x0005000A, 0x0 },/* 3: 600 600 0 */
{ 0x00E79FFF, 0x001D0007, 0x0 },/* 4: 600 750 2 */
{ 0x00D75FFF, 0x000C0004, 0x0 },/* 5: 600 900 3.5 */
{ 0x00FFFFFF, 0x00040006, 0x0 },/* 6: 800 800 0 */
{ 0x80E79FFF, 0x00030002, 0x0 },/* 7: 800 1000 2 */
{ 0x00FFFFFF, 0x00140005, 0x0 },/* 8: 850 850 0 */
{ 0x00FFFFFF, 0x000C0004, 0x0 },/* 9: 900 900 0 */
{ 0x00FFFFFF, 0x001C0003, 0x0 },/* 10: 950 950 0 */
{ 0x80FFFFFF, 0x00030002, 0x0 },/* 11: 1000 1000 0 */
};
static const struct ddi_buf_trans bdw_ddi_translations_edp[] = {
{ 0x00FFFFFF, 0x00000012, 0x0 },
{ 0x00EBAFFF, 0x00020011, 0x0 },
{ 0x00C71FFF, 0x0006000F, 0x0 },
{ 0x00AAAFFF, 0x000E000A, 0x0 },
{ 0x00FFFFFF, 0x00020011, 0x0 },
{ 0x00DB6FFF, 0x0005000F, 0x0 },
{ 0x00BEEFFF, 0x000A000C, 0x0 },
{ 0x00FFFFFF, 0x0005000F, 0x0 },
{ 0x00DB6FFF, 0x000A000C, 0x0 },
};
static const struct ddi_buf_trans bdw_ddi_translations_dp[] = {
{ 0x00FFFFFF, 0x0007000E, 0x0 },
{ 0x00D75FFF, 0x000E000A, 0x0 },
{ 0x00BEFFFF, 0x00140006, 0x0 },
{ 0x80B2CFFF, 0x001B0002, 0x0 },
{ 0x00FFFFFF, 0x000E000A, 0x0 },
{ 0x00DB6FFF, 0x00160005, 0x0 },
{ 0x80C71FFF, 0x001A0002, 0x0 },
{ 0x00F7DFFF, 0x00180004, 0x0 },
{ 0x80D75FFF, 0x001B0002, 0x0 },
};
static const struct ddi_buf_trans bdw_ddi_translations_fdi[] = {
{ 0x00FFFFFF, 0x0001000E, 0x0 },
{ 0x00D75FFF, 0x0004000A, 0x0 },
{ 0x00C30FFF, 0x00070006, 0x0 },
{ 0x00AAAFFF, 0x000C0000, 0x0 },
{ 0x00FFFFFF, 0x0004000A, 0x0 },
{ 0x00D75FFF, 0x00090004, 0x0 },
{ 0x00C30FFF, 0x000C0000, 0x0 },
{ 0x00FFFFFF, 0x00070006, 0x0 },
{ 0x00D75FFF, 0x000C0000, 0x0 },
};
static const struct ddi_buf_trans bdw_ddi_translations_hdmi[] = {
/* Idx NT mV d T mV df db */
{ 0x00FFFFFF, 0x0007000E, 0x0 },/* 0: 400 400 0 */
{ 0x00D75FFF, 0x000E000A, 0x0 },/* 1: 400 600 3.5 */
{ 0x00BEFFFF, 0x00140006, 0x0 },/* 2: 400 800 6 */
{ 0x00FFFFFF, 0x0009000D, 0x0 },/* 3: 450 450 0 */
{ 0x00FFFFFF, 0x000E000A, 0x0 },/* 4: 600 600 0 */
{ 0x00D7FFFF, 0x00140006, 0x0 },/* 5: 600 800 2.5 */
{ 0x80CB2FFF, 0x001B0002, 0x0 },/* 6: 600 1000 4.5 */
{ 0x00FFFFFF, 0x00140006, 0x0 },/* 7: 800 800 0 */
{ 0x80E79FFF, 0x001B0002, 0x0 },/* 8: 800 1000 2 */
{ 0x80FFFFFF, 0x001B0002, 0x0 },/* 9: 1000 1000 0 */
};
/* Skylake H and S */
static const struct ddi_buf_trans skl_ddi_translations_dp[] = {
{ 0x00002016, 0x000000A0, 0x0 },
{ 0x00005012, 0x0000009B, 0x0 },
{ 0x00007011, 0x00000088, 0x0 },
{ 0x80009010, 0x000000C0, 0x1 },
{ 0x00002016, 0x0000009B, 0x0 },
{ 0x00005012, 0x00000088, 0x0 },
{ 0x80007011, 0x000000C0, 0x1 },
{ 0x00002016, 0x000000DF, 0x0 },
{ 0x80005012, 0x000000C0, 0x1 },
};
/* Skylake U */
static const struct ddi_buf_trans skl_u_ddi_translations_dp[] = {
{ 0x0000201B, 0x000000A2, 0x0 },
{ 0x00005012, 0x00000088, 0x0 },
{ 0x80007011, 0x000000CD, 0x1 },
{ 0x80009010, 0x000000C0, 0x1 },
{ 0x0000201B, 0x0000009D, 0x0 },
{ 0x80005012, 0x000000C0, 0x1 },
{ 0x80007011, 0x000000C0, 0x1 },
{ 0x00002016, 0x00000088, 0x0 },
{ 0x80005012, 0x000000C0, 0x1 },
};
/* Skylake Y */
static const struct ddi_buf_trans skl_y_ddi_translations_dp[] = {
{ 0x00000018, 0x000000A2, 0x0 },
{ 0x00005012, 0x00000088, 0x0 },
{ 0x80007011, 0x000000CD, 0x3 },
{ 0x80009010, 0x000000C0, 0x3 },
{ 0x00000018, 0x0000009D, 0x0 },
{ 0x80005012, 0x000000C0, 0x3 },
{ 0x80007011, 0x000000C0, 0x3 },
{ 0x00000018, 0x00000088, 0x0 },
{ 0x80005012, 0x000000C0, 0x3 },
};
/* Kabylake H and S */
static const struct ddi_buf_trans kbl_ddi_translations_dp[] = {
{ 0x00002016, 0x000000A0, 0x0 },
{ 0x00005012, 0x0000009B, 0x0 },
{ 0x00007011, 0x00000088, 0x0 },
{ 0x80009010, 0x000000C0, 0x1 },
{ 0x00002016, 0x0000009B, 0x0 },
{ 0x00005012, 0x00000088, 0x0 },
{ 0x80007011, 0x000000C0, 0x1 },
{ 0x00002016, 0x00000097, 0x0 },
{ 0x80005012, 0x000000C0, 0x1 },
};
/* Kabylake U */
static const struct ddi_buf_trans kbl_u_ddi_translations_dp[] = {
{ 0x0000201B, 0x000000A1, 0x0 },
{ 0x00005012, 0x00000088, 0x0 },
{ 0x80007011, 0x000000CD, 0x3 },
{ 0x80009010, 0x000000C0, 0x3 },
{ 0x0000201B, 0x0000009D, 0x0 },
{ 0x80005012, 0x000000C0, 0x3 },
{ 0x80007011, 0x000000C0, 0x3 },
{ 0x00002016, 0x0000004F, 0x0 },
{ 0x80005012, 0x000000C0, 0x3 },
};
/* Kabylake Y */
static const struct ddi_buf_trans kbl_y_ddi_translations_dp[] = {
{ 0x00001017, 0x000000A1, 0x0 },
{ 0x00005012, 0x00000088, 0x0 },
{ 0x80007011, 0x000000CD, 0x3 },
{ 0x8000800F, 0x000000C0, 0x3 },
{ 0x00001017, 0x0000009D, 0x0 },
{ 0x80005012, 0x000000C0, 0x3 },
{ 0x80007011, 0x000000C0, 0x3 },
{ 0x00001017, 0x0000004C, 0x0 },
{ 0x80005012, 0x000000C0, 0x3 },
};
/*
* Skylake/Kabylake H and S
* eDP 1.4 low vswing translation parameters
*/
static const struct ddi_buf_trans skl_ddi_translations_edp[] = {
{ 0x00000018, 0x000000A8, 0x0 },
{ 0x00004013, 0x000000A9, 0x0 },
{ 0x00007011, 0x000000A2, 0x0 },
{ 0x00009010, 0x0000009C, 0x0 },
{ 0x00000018, 0x000000A9, 0x0 },
{ 0x00006013, 0x000000A2, 0x0 },
{ 0x00007011, 0x000000A6, 0x0 },
{ 0x00000018, 0x000000AB, 0x0 },
{ 0x00007013, 0x0000009F, 0x0 },
{ 0x00000018, 0x000000DF, 0x0 },
};
/*
* Skylake/Kabylake U
* eDP 1.4 low vswing translation parameters
*/
static const struct ddi_buf_trans skl_u_ddi_translations_edp[] = {
{ 0x00000018, 0x000000A8, 0x0 },
{ 0x00004013, 0x000000A9, 0x0 },
{ 0x00007011, 0x000000A2, 0x0 },
{ 0x00009010, 0x0000009C, 0x0 },
{ 0x00000018, 0x000000A9, 0x0 },
{ 0x00006013, 0x000000A2, 0x0 },
{ 0x00007011, 0x000000A6, 0x0 },
{ 0x00002016, 0x000000AB, 0x0 },
{ 0x00005013, 0x0000009F, 0x0 },
{ 0x00000018, 0x000000DF, 0x0 },
};
/*
* Skylake/Kabylake Y
* eDP 1.4 low vswing translation parameters
*/
static const struct ddi_buf_trans skl_y_ddi_translations_edp[] = {
{ 0x00000018, 0x000000A8, 0x0 },
{ 0x00004013, 0x000000AB, 0x0 },
{ 0x00007011, 0x000000A4, 0x0 },
{ 0x00009010, 0x000000DF, 0x0 },
{ 0x00000018, 0x000000AA, 0x0 },
{ 0x00006013, 0x000000A4, 0x0 },
{ 0x00007011, 0x0000009D, 0x0 },
{ 0x00000018, 0x000000A0, 0x0 },
{ 0x00006012, 0x000000DF, 0x0 },
{ 0x00000018, 0x0000008A, 0x0 },
};
/* Skylake/Kabylake U, H and S */
static const struct ddi_buf_trans skl_ddi_translations_hdmi[] = {
{ 0x00000018, 0x000000AC, 0x0 },
{ 0x00005012, 0x0000009D, 0x0 },
{ 0x00007011, 0x00000088, 0x0 },
{ 0x00000018, 0x000000A1, 0x0 },
{ 0x00000018, 0x00000098, 0x0 },
{ 0x00004013, 0x00000088, 0x0 },
{ 0x80006012, 0x000000CD, 0x1 },
{ 0x00000018, 0x000000DF, 0x0 },
{ 0x80003015, 0x000000CD, 0x1 }, /* Default */
{ 0x80003015, 0x000000C0, 0x1 },
{ 0x80000018, 0x000000C0, 0x1 },
};
/* Skylake/Kabylake Y */
static const struct ddi_buf_trans skl_y_ddi_translations_hdmi[] = {
{ 0x00000018, 0x000000A1, 0x0 },
{ 0x00005012, 0x000000DF, 0x0 },
{ 0x80007011, 0x000000CB, 0x3 },
{ 0x00000018, 0x000000A4, 0x0 },
{ 0x00000018, 0x0000009D, 0x0 },
{ 0x00004013, 0x00000080, 0x0 },
{ 0x80006013, 0x000000C0, 0x3 },
{ 0x00000018, 0x0000008A, 0x0 },
{ 0x80003015, 0x000000C0, 0x3 }, /* Default */
{ 0x80003015, 0x000000C0, 0x3 },
{ 0x80000018, 0x000000C0, 0x3 },
};
drm/i915/bxt: VSwing programming sequence VSwing programming sequence as specified in the updated BXT BSpec v2: Satheesh's review comments addressed. - clear value before setting into registers - move print statement to bxt function Other changes - since signal level will not be set into DDI_BUF_CTL, the value need not be returned to intel_dp_set_signal_levels(). Making the bxt specific function to return void and setting signal_levels = 0 for bxt inside intel_dp_set_signal_levels() - instead of signal levels, printing vswing level and pre-emphasis level - in case none of the pre-emphasis levels or vswing levels are set, setting default of 400mV + 0dB v3: Satheesh's review comments - Check for mask before printing signal_levels. - Removing redundant register writes - Call intel_prepare_ddi_buffers only for HAS_PCH_SPLIT - Making register write part generic as it will be required for HDMI as well. Re-structure the code to include an array for vswing related values, set signal levels v4: Satheesh's review comments - Rebase over latest renaming patches - use hsw_signal_levels for HAS_DDI Other changes - Modified vswing_sequence() func definition - Rebased on top of register macro definitions v5: Satheesh's review comments - Check ddi translation table size v6: Imre's review comments - removed comments in vswing sequence - added vswing, pre-emphasis prints in intel_dp_set_signal_levels - added comment explaining use of DP vswing values for eDP - initialize n_entries and ddi_transaltion table based on encoder type - create bxt_ddi_buf_trans structure and use decimal values - adding a flag in bxt buffer translation table to indicate def entry v7: (imre) - squash in Vandana's "VSwing register definition", "HDMI VSwing programming", "Re-enable vswing programming", "Fix vswing sequence" patches - use BXT_PORT_* regs directly instead of via a temp var - simplify BXT_PORT_* macro definitions - add code comment why we read lane while write group registers - fix readout of DP_TRAIN_PRE_EMPHASIS in debug message Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> (v6) Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2014-11-18 10:15:27 +00:00
struct bxt_ddi_buf_trans {
u32 margin; /* swing value */
u32 scale; /* scale value */
u32 enable; /* scale enable */
u32 deemphasis;
bool default_index; /* true if the entry represents default value */
};
static const struct bxt_ddi_buf_trans bxt_ddi_translations_dp[] = {
/* Idx NT mV diff db */
{ 52, 0x9A, 0, 128, true }, /* 0: 400 0 */
{ 78, 0x9A, 0, 85, false }, /* 1: 400 3.5 */
{ 104, 0x9A, 0, 64, false }, /* 2: 400 6 */
{ 154, 0x9A, 0, 43, false }, /* 3: 400 9.5 */
{ 77, 0x9A, 0, 128, false }, /* 4: 600 0 */
{ 116, 0x9A, 0, 85, false }, /* 5: 600 3.5 */
{ 154, 0x9A, 0, 64, false }, /* 6: 600 6 */
{ 102, 0x9A, 0, 128, false }, /* 7: 800 0 */
{ 154, 0x9A, 0, 85, false }, /* 8: 800 3.5 */
{ 154, 0x9A, 1, 128, false }, /* 9: 1200 0 */
drm/i915/bxt: VSwing programming sequence VSwing programming sequence as specified in the updated BXT BSpec v2: Satheesh's review comments addressed. - clear value before setting into registers - move print statement to bxt function Other changes - since signal level will not be set into DDI_BUF_CTL, the value need not be returned to intel_dp_set_signal_levels(). Making the bxt specific function to return void and setting signal_levels = 0 for bxt inside intel_dp_set_signal_levels() - instead of signal levels, printing vswing level and pre-emphasis level - in case none of the pre-emphasis levels or vswing levels are set, setting default of 400mV + 0dB v3: Satheesh's review comments - Check for mask before printing signal_levels. - Removing redundant register writes - Call intel_prepare_ddi_buffers only for HAS_PCH_SPLIT - Making register write part generic as it will be required for HDMI as well. Re-structure the code to include an array for vswing related values, set signal levels v4: Satheesh's review comments - Rebase over latest renaming patches - use hsw_signal_levels for HAS_DDI Other changes - Modified vswing_sequence() func definition - Rebased on top of register macro definitions v5: Satheesh's review comments - Check ddi translation table size v6: Imre's review comments - removed comments in vswing sequence - added vswing, pre-emphasis prints in intel_dp_set_signal_levels - added comment explaining use of DP vswing values for eDP - initialize n_entries and ddi_transaltion table based on encoder type - create bxt_ddi_buf_trans structure and use decimal values - adding a flag in bxt buffer translation table to indicate def entry v7: (imre) - squash in Vandana's "VSwing register definition", "HDMI VSwing programming", "Re-enable vswing programming", "Fix vswing sequence" patches - use BXT_PORT_* regs directly instead of via a temp var - simplify BXT_PORT_* macro definitions - add code comment why we read lane while write group registers - fix readout of DP_TRAIN_PRE_EMPHASIS in debug message Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> (v6) Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2014-11-18 10:15:27 +00:00
};
static const struct bxt_ddi_buf_trans bxt_ddi_translations_edp[] = {
/* Idx NT mV diff db */
{ 26, 0, 0, 128, false }, /* 0: 200 0 */
{ 38, 0, 0, 112, false }, /* 1: 200 1.5 */
{ 48, 0, 0, 96, false }, /* 2: 200 4 */
{ 54, 0, 0, 69, false }, /* 3: 200 6 */
{ 32, 0, 0, 128, false }, /* 4: 250 0 */
{ 48, 0, 0, 104, false }, /* 5: 250 1.5 */
{ 54, 0, 0, 85, false }, /* 6: 250 4 */
{ 43, 0, 0, 128, false }, /* 7: 300 0 */
{ 54, 0, 0, 101, false }, /* 8: 300 1.5 */
{ 48, 0, 0, 128, false }, /* 9: 300 0 */
};
drm/i915/bxt: VSwing programming sequence VSwing programming sequence as specified in the updated BXT BSpec v2: Satheesh's review comments addressed. - clear value before setting into registers - move print statement to bxt function Other changes - since signal level will not be set into DDI_BUF_CTL, the value need not be returned to intel_dp_set_signal_levels(). Making the bxt specific function to return void and setting signal_levels = 0 for bxt inside intel_dp_set_signal_levels() - instead of signal levels, printing vswing level and pre-emphasis level - in case none of the pre-emphasis levels or vswing levels are set, setting default of 400mV + 0dB v3: Satheesh's review comments - Check for mask before printing signal_levels. - Removing redundant register writes - Call intel_prepare_ddi_buffers only for HAS_PCH_SPLIT - Making register write part generic as it will be required for HDMI as well. Re-structure the code to include an array for vswing related values, set signal levels v4: Satheesh's review comments - Rebase over latest renaming patches - use hsw_signal_levels for HAS_DDI Other changes - Modified vswing_sequence() func definition - Rebased on top of register macro definitions v5: Satheesh's review comments - Check ddi translation table size v6: Imre's review comments - removed comments in vswing sequence - added vswing, pre-emphasis prints in intel_dp_set_signal_levels - added comment explaining use of DP vswing values for eDP - initialize n_entries and ddi_transaltion table based on encoder type - create bxt_ddi_buf_trans structure and use decimal values - adding a flag in bxt buffer translation table to indicate def entry v7: (imre) - squash in Vandana's "VSwing register definition", "HDMI VSwing programming", "Re-enable vswing programming", "Fix vswing sequence" patches - use BXT_PORT_* regs directly instead of via a temp var - simplify BXT_PORT_* macro definitions - add code comment why we read lane while write group registers - fix readout of DP_TRAIN_PRE_EMPHASIS in debug message Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> (v6) Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2014-11-18 10:15:27 +00:00
/* BSpec has 2 recommended values - entries 0 and 8.
* Using the entry with higher vswing.
*/
static const struct bxt_ddi_buf_trans bxt_ddi_translations_hdmi[] = {
/* Idx NT mV diff db */
{ 52, 0x9A, 0, 128, false }, /* 0: 400 0 */
{ 52, 0x9A, 0, 85, false }, /* 1: 400 3.5 */
{ 52, 0x9A, 0, 64, false }, /* 2: 400 6 */
{ 42, 0x9A, 0, 43, false }, /* 3: 400 9.5 */
{ 77, 0x9A, 0, 128, false }, /* 4: 600 0 */
{ 77, 0x9A, 0, 85, false }, /* 5: 600 3.5 */
{ 77, 0x9A, 0, 64, false }, /* 6: 600 6 */
{ 102, 0x9A, 0, 128, false }, /* 7: 800 0 */
{ 102, 0x9A, 0, 85, false }, /* 8: 800 3.5 */
drm/i915/bxt: VSwing programming sequence VSwing programming sequence as specified in the updated BXT BSpec v2: Satheesh's review comments addressed. - clear value before setting into registers - move print statement to bxt function Other changes - since signal level will not be set into DDI_BUF_CTL, the value need not be returned to intel_dp_set_signal_levels(). Making the bxt specific function to return void and setting signal_levels = 0 for bxt inside intel_dp_set_signal_levels() - instead of signal levels, printing vswing level and pre-emphasis level - in case none of the pre-emphasis levels or vswing levels are set, setting default of 400mV + 0dB v3: Satheesh's review comments - Check for mask before printing signal_levels. - Removing redundant register writes - Call intel_prepare_ddi_buffers only for HAS_PCH_SPLIT - Making register write part generic as it will be required for HDMI as well. Re-structure the code to include an array for vswing related values, set signal levels v4: Satheesh's review comments - Rebase over latest renaming patches - use hsw_signal_levels for HAS_DDI Other changes - Modified vswing_sequence() func definition - Rebased on top of register macro definitions v5: Satheesh's review comments - Check ddi translation table size v6: Imre's review comments - removed comments in vswing sequence - added vswing, pre-emphasis prints in intel_dp_set_signal_levels - added comment explaining use of DP vswing values for eDP - initialize n_entries and ddi_transaltion table based on encoder type - create bxt_ddi_buf_trans structure and use decimal values - adding a flag in bxt buffer translation table to indicate def entry v7: (imre) - squash in Vandana's "VSwing register definition", "HDMI VSwing programming", "Re-enable vswing programming", "Fix vswing sequence" patches - use BXT_PORT_* regs directly instead of via a temp var - simplify BXT_PORT_* macro definitions - add code comment why we read lane while write group registers - fix readout of DP_TRAIN_PRE_EMPHASIS in debug message Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> (v6) Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2014-11-18 10:15:27 +00:00
{ 154, 0x9A, 1, 128, true }, /* 9: 1200 0 */
};
struct cnl_ddi_buf_trans {
u32 dw2_swing_sel;
u32 dw7_n_scalar;
u32 dw4_cursor_coeff;
u32 dw4_post_cursor_2;
u32 dw4_post_cursor_1;
};
/* Voltage Swing Programming for VccIO 0.85V for DP */
static const struct cnl_ddi_buf_trans cnl_ddi_translations_dp_0_85V[] = {
/* NT mV Trans mV db */
{ 0xA, 0x5D, 0x3F, 0x00, 0x00 }, /* 350 350 0.0 */
{ 0xA, 0x6A, 0x38, 0x00, 0x07 }, /* 350 500 3.1 */
{ 0xB, 0x7A, 0x32, 0x00, 0x0D }, /* 350 700 6.0 */
{ 0x6, 0x7C, 0x2D, 0x00, 0x12 }, /* 350 900 8.2 */
{ 0xA, 0x69, 0x3F, 0x00, 0x00 }, /* 500 500 0.0 */
{ 0xB, 0x7A, 0x36, 0x00, 0x09 }, /* 500 700 2.9 */
{ 0x6, 0x7C, 0x30, 0x00, 0x0F }, /* 500 900 5.1 */
{ 0xB, 0x7D, 0x3C, 0x00, 0x03 }, /* 650 725 0.9 */
{ 0x6, 0x7C, 0x34, 0x00, 0x0B }, /* 600 900 3.5 */
{ 0x6, 0x7B, 0x3F, 0x00, 0x00 }, /* 900 900 0.0 */
};
/* Voltage Swing Programming for VccIO 0.85V for HDMI */
static const struct cnl_ddi_buf_trans cnl_ddi_translations_hdmi_0_85V[] = {
/* NT mV Trans mV db */
{ 0xA, 0x60, 0x3F, 0x00, 0x00 }, /* 450 450 0.0 */
{ 0xB, 0x73, 0x36, 0x00, 0x09 }, /* 450 650 3.2 */
{ 0x6, 0x7F, 0x31, 0x00, 0x0E }, /* 450 850 5.5 */
{ 0xB, 0x73, 0x3F, 0x00, 0x00 }, /* 650 650 0.0 */
{ 0x6, 0x7F, 0x37, 0x00, 0x08 }, /* 650 850 2.3 */
{ 0x6, 0x7F, 0x3F, 0x00, 0x00 }, /* 850 850 0.0 */
{ 0x6, 0x7F, 0x35, 0x00, 0x0A }, /* 600 850 3.0 */
};
/* Voltage Swing Programming for VccIO 0.85V for eDP */
static const struct cnl_ddi_buf_trans cnl_ddi_translations_edp_0_85V[] = {
/* NT mV Trans mV db */
{ 0xA, 0x66, 0x3A, 0x00, 0x05 }, /* 384 500 2.3 */
{ 0x0, 0x7F, 0x38, 0x00, 0x07 }, /* 153 200 2.3 */
{ 0x8, 0x7F, 0x38, 0x00, 0x07 }, /* 192 250 2.3 */
{ 0x1, 0x7F, 0x38, 0x00, 0x07 }, /* 230 300 2.3 */
{ 0x9, 0x7F, 0x38, 0x00, 0x07 }, /* 269 350 2.3 */
{ 0xA, 0x66, 0x3C, 0x00, 0x03 }, /* 446 500 1.0 */
{ 0xB, 0x70, 0x3C, 0x00, 0x03 }, /* 460 600 2.3 */
{ 0xC, 0x75, 0x3C, 0x00, 0x03 }, /* 537 700 2.3 */
{ 0x2, 0x7F, 0x3F, 0x00, 0x00 }, /* 400 400 0.0 */
};
/* Voltage Swing Programming for VccIO 0.95V for DP */
static const struct cnl_ddi_buf_trans cnl_ddi_translations_dp_0_95V[] = {
/* NT mV Trans mV db */
{ 0xA, 0x5D, 0x3F, 0x00, 0x00 }, /* 350 350 0.0 */
{ 0xA, 0x6A, 0x38, 0x00, 0x07 }, /* 350 500 3.1 */
{ 0xB, 0x7A, 0x32, 0x00, 0x0D }, /* 350 700 6.0 */
{ 0x6, 0x7C, 0x2D, 0x00, 0x12 }, /* 350 900 8.2 */
{ 0xA, 0x69, 0x3F, 0x00, 0x00 }, /* 500 500 0.0 */
{ 0xB, 0x7A, 0x36, 0x00, 0x09 }, /* 500 700 2.9 */
{ 0x6, 0x7C, 0x30, 0x00, 0x0F }, /* 500 900 5.1 */
{ 0xB, 0x7D, 0x3C, 0x00, 0x03 }, /* 650 725 0.9 */
{ 0x6, 0x7C, 0x34, 0x00, 0x0B }, /* 600 900 3.5 */
{ 0x6, 0x7B, 0x3F, 0x00, 0x00 }, /* 900 900 0.0 */
};
/* Voltage Swing Programming for VccIO 0.95V for HDMI */
static const struct cnl_ddi_buf_trans cnl_ddi_translations_hdmi_0_95V[] = {
/* NT mV Trans mV db */
{ 0xA, 0x5C, 0x3F, 0x00, 0x00 }, /* 400 400 0.0 */
{ 0xB, 0x69, 0x37, 0x00, 0x08 }, /* 400 600 3.5 */
{ 0x5, 0x76, 0x31, 0x00, 0x0E }, /* 400 800 6.0 */
{ 0xA, 0x5E, 0x3F, 0x00, 0x00 }, /* 450 450 0.0 */
{ 0xB, 0x69, 0x3F, 0x00, 0x00 }, /* 600 600 0.0 */
{ 0xB, 0x79, 0x35, 0x00, 0x0A }, /* 600 850 3.0 */
{ 0x6, 0x7D, 0x32, 0x00, 0x0D }, /* 600 1000 4.4 */
{ 0x5, 0x76, 0x3F, 0x00, 0x00 }, /* 800 800 0.0 */
{ 0x6, 0x7D, 0x39, 0x00, 0x06 }, /* 800 1000 1.9 */
{ 0x6, 0x7F, 0x39, 0x00, 0x06 }, /* 850 1050 1.8 */
{ 0x6, 0x7F, 0x3F, 0x00, 0x00 }, /* 1050 1050 0.0 */
};
/* Voltage Swing Programming for VccIO 0.95V for eDP */
static const struct cnl_ddi_buf_trans cnl_ddi_translations_edp_0_95V[] = {
/* NT mV Trans mV db */
{ 0xA, 0x61, 0x3A, 0x00, 0x05 }, /* 384 500 2.3 */
{ 0x0, 0x7F, 0x38, 0x00, 0x07 }, /* 153 200 2.3 */
{ 0x8, 0x7F, 0x38, 0x00, 0x07 }, /* 192 250 2.3 */
{ 0x1, 0x7F, 0x38, 0x00, 0x07 }, /* 230 300 2.3 */
{ 0x9, 0x7F, 0x38, 0x00, 0x07 }, /* 269 350 2.3 */
{ 0xA, 0x61, 0x3C, 0x00, 0x03 }, /* 446 500 1.0 */
{ 0xB, 0x68, 0x39, 0x00, 0x06 }, /* 460 600 2.3 */
{ 0xC, 0x6E, 0x39, 0x00, 0x06 }, /* 537 700 2.3 */
{ 0x4, 0x7F, 0x3A, 0x00, 0x05 }, /* 460 600 2.3 */
{ 0x2, 0x7F, 0x3F, 0x00, 0x00 }, /* 400 400 0.0 */
};
/* Voltage Swing Programming for VccIO 1.05V for DP */
static const struct cnl_ddi_buf_trans cnl_ddi_translations_dp_1_05V[] = {
/* NT mV Trans mV db */
{ 0xA, 0x58, 0x3F, 0x00, 0x00 }, /* 400 400 0.0 */
{ 0xB, 0x64, 0x37, 0x00, 0x08 }, /* 400 600 3.5 */
{ 0x5, 0x70, 0x31, 0x00, 0x0E }, /* 400 800 6.0 */
{ 0x6, 0x7F, 0x2C, 0x00, 0x13 }, /* 400 1050 8.4 */
{ 0xB, 0x64, 0x3F, 0x00, 0x00 }, /* 600 600 0.0 */
{ 0x5, 0x73, 0x35, 0x00, 0x0A }, /* 600 850 3.0 */
{ 0x6, 0x7F, 0x30, 0x00, 0x0F }, /* 550 1050 5.6 */
{ 0x5, 0x76, 0x3E, 0x00, 0x01 }, /* 850 900 0.5 */
{ 0x6, 0x7F, 0x36, 0x00, 0x09 }, /* 750 1050 2.9 */
{ 0x6, 0x7F, 0x3F, 0x00, 0x00 }, /* 1050 1050 0.0 */
};
/* Voltage Swing Programming for VccIO 1.05V for HDMI */
static const struct cnl_ddi_buf_trans cnl_ddi_translations_hdmi_1_05V[] = {
/* NT mV Trans mV db */
{ 0xA, 0x58, 0x3F, 0x00, 0x00 }, /* 400 400 0.0 */
{ 0xB, 0x64, 0x37, 0x00, 0x08 }, /* 400 600 3.5 */
{ 0x5, 0x70, 0x31, 0x00, 0x0E }, /* 400 800 6.0 */
{ 0xA, 0x5B, 0x3F, 0x00, 0x00 }, /* 450 450 0.0 */
{ 0xB, 0x64, 0x3F, 0x00, 0x00 }, /* 600 600 0.0 */
{ 0x5, 0x73, 0x35, 0x00, 0x0A }, /* 600 850 3.0 */
{ 0x6, 0x7C, 0x32, 0x00, 0x0D }, /* 600 1000 4.4 */
{ 0x5, 0x70, 0x3F, 0x00, 0x00 }, /* 800 800 0.0 */
{ 0x6, 0x7C, 0x39, 0x00, 0x06 }, /* 800 1000 1.9 */
{ 0x6, 0x7F, 0x39, 0x00, 0x06 }, /* 850 1050 1.8 */
{ 0x6, 0x7F, 0x3F, 0x00, 0x00 }, /* 1050 1050 0.0 */
};
/* Voltage Swing Programming for VccIO 1.05V for eDP */
static const struct cnl_ddi_buf_trans cnl_ddi_translations_edp_1_05V[] = {
/* NT mV Trans mV db */
{ 0xA, 0x5E, 0x3A, 0x00, 0x05 }, /* 384 500 2.3 */
{ 0x0, 0x7F, 0x38, 0x00, 0x07 }, /* 153 200 2.3 */
{ 0x8, 0x7F, 0x38, 0x00, 0x07 }, /* 192 250 2.3 */
{ 0x1, 0x7F, 0x38, 0x00, 0x07 }, /* 230 300 2.3 */
{ 0x9, 0x7F, 0x38, 0x00, 0x07 }, /* 269 350 2.3 */
{ 0xA, 0x5E, 0x3C, 0x00, 0x03 }, /* 446 500 1.0 */
{ 0xB, 0x64, 0x39, 0x00, 0x06 }, /* 460 600 2.3 */
{ 0xE, 0x6A, 0x39, 0x00, 0x06 }, /* 537 700 2.3 */
{ 0x2, 0x7F, 0x3F, 0x00, 0x00 }, /* 400 400 0.0 */
};
enum port intel_ddi_get_encoder_port(struct intel_encoder *encoder)
{
switch (encoder->type) {
case INTEL_OUTPUT_DP_MST:
return enc_to_mst(&encoder->base)->primary->port;
case INTEL_OUTPUT_DP:
case INTEL_OUTPUT_EDP:
case INTEL_OUTPUT_HDMI:
case INTEL_OUTPUT_UNKNOWN:
return enc_to_dig_port(&encoder->base)->port;
case INTEL_OUTPUT_ANALOG:
return PORT_E;
default:
MISSING_CASE(encoder->type);
return PORT_A;
}
}
static const struct ddi_buf_trans *
bdw_get_buf_trans_edp(struct drm_i915_private *dev_priv, int *n_entries)
{
if (dev_priv->vbt.edp.low_vswing) {
*n_entries = ARRAY_SIZE(bdw_ddi_translations_edp);
return bdw_ddi_translations_edp;
} else {
*n_entries = ARRAY_SIZE(bdw_ddi_translations_dp);
return bdw_ddi_translations_dp;
}
}
static const struct ddi_buf_trans *
skl_get_buf_trans_dp(struct drm_i915_private *dev_priv, int *n_entries)
{
if (IS_SKL_ULX(dev_priv)) {
*n_entries = ARRAY_SIZE(skl_y_ddi_translations_dp);
return skl_y_ddi_translations_dp;
} else if (IS_SKL_ULT(dev_priv)) {
*n_entries = ARRAY_SIZE(skl_u_ddi_translations_dp);
return skl_u_ddi_translations_dp;
} else {
*n_entries = ARRAY_SIZE(skl_ddi_translations_dp);
return skl_ddi_translations_dp;
}
}
static const struct ddi_buf_trans *
kbl_get_buf_trans_dp(struct drm_i915_private *dev_priv, int *n_entries)
{
if (IS_KBL_ULX(dev_priv)) {
*n_entries = ARRAY_SIZE(kbl_y_ddi_translations_dp);
return kbl_y_ddi_translations_dp;
} else if (IS_KBL_ULT(dev_priv) || IS_CFL_ULT(dev_priv)) {
*n_entries = ARRAY_SIZE(kbl_u_ddi_translations_dp);
return kbl_u_ddi_translations_dp;
} else {
*n_entries = ARRAY_SIZE(kbl_ddi_translations_dp);
return kbl_ddi_translations_dp;
}
}
static const struct ddi_buf_trans *
skl_get_buf_trans_edp(struct drm_i915_private *dev_priv, int *n_entries)
{
if (dev_priv->vbt.edp.low_vswing) {
if (IS_SKL_ULX(dev_priv) || IS_KBL_ULX(dev_priv)) {
*n_entries = ARRAY_SIZE(skl_y_ddi_translations_edp);
return skl_y_ddi_translations_edp;
} else if (IS_SKL_ULT(dev_priv) || IS_KBL_ULT(dev_priv) ||
IS_CFL_ULT(dev_priv)) {
*n_entries = ARRAY_SIZE(skl_u_ddi_translations_edp);
return skl_u_ddi_translations_edp;
} else {
*n_entries = ARRAY_SIZE(skl_ddi_translations_edp);
return skl_ddi_translations_edp;
}
}
if (IS_KABYLAKE(dev_priv) || IS_COFFEELAKE(dev_priv))
return kbl_get_buf_trans_dp(dev_priv, n_entries);
else
return skl_get_buf_trans_dp(dev_priv, n_entries);
}
static const struct ddi_buf_trans *
skl_get_buf_trans_hdmi(struct drm_i915_private *dev_priv, int *n_entries)
{
if (IS_SKL_ULX(dev_priv) || IS_KBL_ULX(dev_priv)) {
*n_entries = ARRAY_SIZE(skl_y_ddi_translations_hdmi);
return skl_y_ddi_translations_hdmi;
} else {
*n_entries = ARRAY_SIZE(skl_ddi_translations_hdmi);
return skl_ddi_translations_hdmi;
}
}
static int intel_ddi_hdmi_level(struct drm_i915_private *dev_priv, enum port port)
{
int n_hdmi_entries;
int hdmi_level;
int hdmi_default_entry;
hdmi_level = dev_priv->vbt.ddi_port_info[port].hdmi_level_shift;
if (IS_GEN9_LP(dev_priv))
return hdmi_level;
if (IS_GEN9_BC(dev_priv)) {
skl_get_buf_trans_hdmi(dev_priv, &n_hdmi_entries);
hdmi_default_entry = 8;
} else if (IS_BROADWELL(dev_priv)) {
n_hdmi_entries = ARRAY_SIZE(bdw_ddi_translations_hdmi);
hdmi_default_entry = 7;
} else if (IS_HASWELL(dev_priv)) {
n_hdmi_entries = ARRAY_SIZE(hsw_ddi_translations_hdmi);
hdmi_default_entry = 6;
} else {
WARN(1, "ddi translation table missing\n");
n_hdmi_entries = ARRAY_SIZE(bdw_ddi_translations_hdmi);
hdmi_default_entry = 7;
}
/* Choose a good default if VBT is badly populated */
if (hdmi_level == HDMI_LEVEL_SHIFT_UNKNOWN ||
hdmi_level >= n_hdmi_entries)
hdmi_level = hdmi_default_entry;
return hdmi_level;
}
static const struct ddi_buf_trans *
intel_ddi_get_buf_trans_dp(struct drm_i915_private *dev_priv,
int *n_entries)
{
if (IS_KABYLAKE(dev_priv) || IS_COFFEELAKE(dev_priv)) {
return kbl_get_buf_trans_dp(dev_priv, n_entries);
} else if (IS_SKYLAKE(dev_priv)) {
return skl_get_buf_trans_dp(dev_priv, n_entries);
} else if (IS_BROADWELL(dev_priv)) {
*n_entries = ARRAY_SIZE(bdw_ddi_translations_dp);
return bdw_ddi_translations_dp;
} else if (IS_HASWELL(dev_priv)) {
*n_entries = ARRAY_SIZE(hsw_ddi_translations_dp);
return hsw_ddi_translations_dp;
}
*n_entries = 0;
return NULL;
}
static const struct ddi_buf_trans *
intel_ddi_get_buf_trans_edp(struct drm_i915_private *dev_priv,
int *n_entries)
{
if (IS_GEN9_BC(dev_priv)) {
return skl_get_buf_trans_edp(dev_priv, n_entries);
} else if (IS_BROADWELL(dev_priv)) {
return bdw_get_buf_trans_edp(dev_priv, n_entries);
} else if (IS_HASWELL(dev_priv)) {
*n_entries = ARRAY_SIZE(hsw_ddi_translations_dp);
return hsw_ddi_translations_dp;
}
*n_entries = 0;
return NULL;
}
static const struct ddi_buf_trans *
intel_ddi_get_buf_trans_fdi(struct drm_i915_private *dev_priv,
int *n_entries)
{
if (IS_BROADWELL(dev_priv)) {
*n_entries = ARRAY_SIZE(hsw_ddi_translations_fdi);
return hsw_ddi_translations_fdi;
} else if (IS_HASWELL(dev_priv)) {
*n_entries = ARRAY_SIZE(hsw_ddi_translations_fdi);
return hsw_ddi_translations_fdi;
}
*n_entries = 0;
return NULL;
}
/*
* Starting with Haswell, DDI port buffers must be programmed with correct
* values in advance. This function programs the correct values for
* DP/eDP/FDI use cases.
*/
static void intel_prepare_dp_ddi_buffers(struct intel_encoder *encoder)
{
struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
u32 iboost_bit = 0;
int i, n_entries;
enum port port = intel_ddi_get_encoder_port(encoder);
const struct ddi_buf_trans *ddi_translations;
if (IS_GEN9_LP(dev_priv))
drm/i915/bxt: VSwing programming sequence VSwing programming sequence as specified in the updated BXT BSpec v2: Satheesh's review comments addressed. - clear value before setting into registers - move print statement to bxt function Other changes - since signal level will not be set into DDI_BUF_CTL, the value need not be returned to intel_dp_set_signal_levels(). Making the bxt specific function to return void and setting signal_levels = 0 for bxt inside intel_dp_set_signal_levels() - instead of signal levels, printing vswing level and pre-emphasis level - in case none of the pre-emphasis levels or vswing levels are set, setting default of 400mV + 0dB v3: Satheesh's review comments - Check for mask before printing signal_levels. - Removing redundant register writes - Call intel_prepare_ddi_buffers only for HAS_PCH_SPLIT - Making register write part generic as it will be required for HDMI as well. Re-structure the code to include an array for vswing related values, set signal levels v4: Satheesh's review comments - Rebase over latest renaming patches - use hsw_signal_levels for HAS_DDI Other changes - Modified vswing_sequence() func definition - Rebased on top of register macro definitions v5: Satheesh's review comments - Check ddi translation table size v6: Imre's review comments - removed comments in vswing sequence - added vswing, pre-emphasis prints in intel_dp_set_signal_levels - added comment explaining use of DP vswing values for eDP - initialize n_entries and ddi_transaltion table based on encoder type - create bxt_ddi_buf_trans structure and use decimal values - adding a flag in bxt buffer translation table to indicate def entry v7: (imre) - squash in Vandana's "VSwing register definition", "HDMI VSwing programming", "Re-enable vswing programming", "Fix vswing sequence" patches - use BXT_PORT_* regs directly instead of via a temp var - simplify BXT_PORT_* macro definitions - add code comment why we read lane while write group registers - fix readout of DP_TRAIN_PRE_EMPHASIS in debug message Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> (v6) Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2014-11-18 10:15:27 +00:00
return;
switch (encoder->type) {
case INTEL_OUTPUT_EDP:
ddi_translations = intel_ddi_get_buf_trans_edp(dev_priv,
&n_entries);
break;
case INTEL_OUTPUT_DP:
ddi_translations = intel_ddi_get_buf_trans_dp(dev_priv,
&n_entries);
break;
case INTEL_OUTPUT_ANALOG:
ddi_translations = intel_ddi_get_buf_trans_fdi(dev_priv,
&n_entries);
break;
default:
MISSING_CASE(encoder->type);
return;
}
if (IS_GEN9_BC(dev_priv)) {
/* If we're boosting the current, set bit 31 of trans1 */
if (dev_priv->vbt.ddi_port_info[port].dp_boost_level)
iboost_bit = DDI_BUF_BALANCE_LEG_ENABLE;
if (WARN_ON(encoder->type == INTEL_OUTPUT_EDP &&
port != PORT_A && port != PORT_E &&
n_entries > 9))
n_entries = 9;
}
for (i = 0; i < n_entries; i++) {
I915_WRITE(DDI_BUF_TRANS_LO(port, i),
ddi_translations[i].trans1 | iboost_bit);
I915_WRITE(DDI_BUF_TRANS_HI(port, i),
ddi_translations[i].trans2);
}
}
/*
* Starting with Haswell, DDI port buffers must be programmed with correct
* values in advance. This function programs the correct values for
* HDMI/DVI use cases.
*/
static void intel_prepare_hdmi_ddi_buffers(struct intel_encoder *encoder)
{
struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
u32 iboost_bit = 0;
int n_hdmi_entries, hdmi_level;
enum port port = intel_ddi_get_encoder_port(encoder);
const struct ddi_buf_trans *ddi_translations_hdmi;
if (IS_GEN9_LP(dev_priv))
return;
hdmi_level = intel_ddi_hdmi_level(dev_priv, port);
if (IS_GEN9_BC(dev_priv)) {
ddi_translations_hdmi = skl_get_buf_trans_hdmi(dev_priv, &n_hdmi_entries);
/* If we're boosting the current, set bit 31 of trans1 */
if (dev_priv->vbt.ddi_port_info[port].hdmi_boost_level)
iboost_bit = DDI_BUF_BALANCE_LEG_ENABLE;
} else if (IS_BROADWELL(dev_priv)) {
ddi_translations_hdmi = bdw_ddi_translations_hdmi;
n_hdmi_entries = ARRAY_SIZE(bdw_ddi_translations_hdmi);
} else if (IS_HASWELL(dev_priv)) {
ddi_translations_hdmi = hsw_ddi_translations_hdmi;
n_hdmi_entries = ARRAY_SIZE(hsw_ddi_translations_hdmi);
} else {
WARN(1, "ddi translation table missing\n");
ddi_translations_hdmi = bdw_ddi_translations_hdmi;
n_hdmi_entries = ARRAY_SIZE(bdw_ddi_translations_hdmi);
}
/* Entry 9 is for HDMI: */
I915_WRITE(DDI_BUF_TRANS_LO(port, 9),
ddi_translations_hdmi[hdmi_level].trans1 | iboost_bit);
I915_WRITE(DDI_BUF_TRANS_HI(port, 9),
ddi_translations_hdmi[hdmi_level].trans2);
}
static void intel_wait_ddi_buf_idle(struct drm_i915_private *dev_priv,
enum port port)
{
drm/i915: Type safe register read/write Make I915_READ and I915_WRITE more type safe by wrapping the register offset in a struct. This should eliminate most of the fumbles we've had with misplaced parens. This only takes care of normal mmio registers. We could extend the idea to other register types and define each with its own struct. That way you wouldn't be able to accidentally pass the wrong thing to a specific register access function. The gpio_reg setup is probably the ugliest thing left. But I figure I'd just leave it for now, and wait for some divine inspiration to strike before making it nice. As for the generated code, it's actually a bit better sometimes. Eg. looking at i915_irq_handler(), we can see the following change: lea 0x70024(%rdx,%rax,1),%r9d mov $0x1,%edx - movslq %r9d,%r9 - mov %r9,%rsi - mov %r9,-0x58(%rbp) - callq *0xd8(%rbx) + mov %r9d,%esi + mov %r9d,-0x48(%rbp) callq *0xd8(%rbx) So previously gcc thought the register offset might be signed and decided to sign extend it, just in case. The rest appears to be mostly just minor shuffling of instructions. v2: i915_mmio_reg_{offset,equal,valid}() helpers added s/_REG/_MMIO/ in the register defines mo more switch statements left to worry about ring_emit stuff got sorted in a prep patch cmd parser, lrc context and w/a batch buildup also in prep patch vgpu stuff cleaned up and moved to a prep patch all other unrelated changes split out v3: Rebased due to BXT DSI/BLC, MOCS, etc. v4: Rebased due to churn, s/i915_mmio_reg_t/i915_reg_t/ Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Link: http://patchwork.freedesktop.org/patch/msgid/1447853606-2751-1-git-send-email-ville.syrjala@linux.intel.com
2015-11-18 13:33:26 +00:00
i915_reg_t reg = DDI_BUF_CTL(port);
int i;
for (i = 0; i < 16; i++) {
udelay(1);
if (I915_READ(reg) & DDI_BUF_IS_IDLE)
return;
}
DRM_ERROR("Timeout waiting for DDI BUF %c idle bit\n", port_name(port));
}
static uint32_t hsw_pll_to_ddi_pll_sel(struct intel_shared_dpll *pll)
{
switch (pll->id) {
case DPLL_ID_WRPLL1:
return PORT_CLK_SEL_WRPLL1;
case DPLL_ID_WRPLL2:
return PORT_CLK_SEL_WRPLL2;
case DPLL_ID_SPLL:
return PORT_CLK_SEL_SPLL;
case DPLL_ID_LCPLL_810:
return PORT_CLK_SEL_LCPLL_810;
case DPLL_ID_LCPLL_1350:
return PORT_CLK_SEL_LCPLL_1350;
case DPLL_ID_LCPLL_2700:
return PORT_CLK_SEL_LCPLL_2700;
default:
MISSING_CASE(pll->id);
return PORT_CLK_SEL_NONE;
}
}
/* Starting with Haswell, different DDI ports can work in FDI mode for
* connection to the PCH-located connectors. For this, it is necessary to train
* both the DDI port and PCH receiver for the desired DDI buffer settings.
*
* The recommended port to work in FDI mode is DDI E, which we use here. Also,
* please note that when FDI mode is active on DDI E, it shares 2 lines with
* DDI A (which is used for eDP)
*/
void hsw_fdi_link_train(struct intel_crtc *crtc,
const struct intel_crtc_state *crtc_state)
{
struct drm_device *dev = crtc->base.dev;
struct drm_i915_private *dev_priv = to_i915(dev);
struct intel_encoder *encoder;
u32 temp, i, rx_ctl_val, ddi_pll_sel;
for_each_encoder_on_crtc(dev, &crtc->base, encoder) {
WARN_ON(encoder->type != INTEL_OUTPUT_ANALOG);
intel_prepare_dp_ddi_buffers(encoder);
}
drm/i915: fix Haswell FDI link training code This commit makes hsw_fdi_link_train responsible for implementing everything described in the "Enable and train FDI" section from the Hawell CRT mode set sequence documentation. We completely rewrite hsw_fdi_link_train to match the documentation and we also call it in the right place. This patch was initially sent as a series of tiny patches fixing every little problem of the function, but since there were too many patches fixing the same function it got a little difficult to get the "big picture" of how the function would be in the end, so here we amended all the patches into a single big patch fixing the whole function. Problems we fixed: 1 - Train Haswell FDI at the right time. We need to train the FDI before enabling the pipes and planes, so we're moving the call from lpt_pch_enable to haswell_crtc_enable directly. We are also removing ironlake_fdi_pll_enable since the PLL enablement on Haswell is completely different and is also done during the link training steps. 2 - Use the right FDI_RX_CTL register on Haswell There is only one PCH transcoder, so it's always _FDI_RXA_CTL. Using "pipe" here is wrong. 3 - Don't rely on DDI_BUF_CTL previous values Just set the bits we want, everything else is zero. Also POSTING_READ the register before sleeping. 4 - Program the FDI RX TUSIZE register on hsw_fdi_link_train According to the mode set sequence documentation, this is the right place. According to the FDI_RX_TUSIZE register description, this is the value we should set. Also remove the code that sets this register from the old location: lpt_pch_enable. 5 - Properly program FDI_RX_MISC pwrdn lane values on HSW 6 - Wait only 35us for the FDI link training First we wait 30us for the FDI receiver lane calibration, then we wait 5us for the FDI auto training time. 7 - Remove an useless indentation level on hsw_fdi_link_train We already "break" when the link training succeeds. 8 - Disable FDI_RX_ENABLE, not FDI_RX_PLL_ENABLE When we fail the training. 9 - Change Haswell FDI link training error messages We shouldn't call DRM_ERROR when still looping through voltage levels since this is expected and not really a failure. So in this commit we adjust the error path to only DRM_ERROR when we really fail after trying everything. While at it, replace DRM_DEBUG_DRIVER with DRM_DEBUG_KMS since it's what we use everywhere. 10 - Try each voltage twice at hsw_fdi_link_train Now with Daniel Vetter's suggestion to use "/2" instead of ">>1". Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> [danvet: Applied tiny bikesheds: - mention in comment that we test each voltage/emphasis level twice - realing arguments of the only untouched reg write, it spilled over the 80 char limit ...] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2012-11-01 23:00:59 +00:00
/* Set the FDI_RX_MISC pwrdn lanes and the 2 workarounds listed at the
* mode set "sequence for CRT port" document:
* - TP1 to TP2 time with the default value
* - FDI delay to 90h
*
* WaFDIAutoLinkSetTimingOverrride:hsw
drm/i915: fix Haswell FDI link training code This commit makes hsw_fdi_link_train responsible for implementing everything described in the "Enable and train FDI" section from the Hawell CRT mode set sequence documentation. We completely rewrite hsw_fdi_link_train to match the documentation and we also call it in the right place. This patch was initially sent as a series of tiny patches fixing every little problem of the function, but since there were too many patches fixing the same function it got a little difficult to get the "big picture" of how the function would be in the end, so here we amended all the patches into a single big patch fixing the whole function. Problems we fixed: 1 - Train Haswell FDI at the right time. We need to train the FDI before enabling the pipes and planes, so we're moving the call from lpt_pch_enable to haswell_crtc_enable directly. We are also removing ironlake_fdi_pll_enable since the PLL enablement on Haswell is completely different and is also done during the link training steps. 2 - Use the right FDI_RX_CTL register on Haswell There is only one PCH transcoder, so it's always _FDI_RXA_CTL. Using "pipe" here is wrong. 3 - Don't rely on DDI_BUF_CTL previous values Just set the bits we want, everything else is zero. Also POSTING_READ the register before sleeping. 4 - Program the FDI RX TUSIZE register on hsw_fdi_link_train According to the mode set sequence documentation, this is the right place. According to the FDI_RX_TUSIZE register description, this is the value we should set. Also remove the code that sets this register from the old location: lpt_pch_enable. 5 - Properly program FDI_RX_MISC pwrdn lane values on HSW 6 - Wait only 35us for the FDI link training First we wait 30us for the FDI receiver lane calibration, then we wait 5us for the FDI auto training time. 7 - Remove an useless indentation level on hsw_fdi_link_train We already "break" when the link training succeeds. 8 - Disable FDI_RX_ENABLE, not FDI_RX_PLL_ENABLE When we fail the training. 9 - Change Haswell FDI link training error messages We shouldn't call DRM_ERROR when still looping through voltage levels since this is expected and not really a failure. So in this commit we adjust the error path to only DRM_ERROR when we really fail after trying everything. While at it, replace DRM_DEBUG_DRIVER with DRM_DEBUG_KMS since it's what we use everywhere. 10 - Try each voltage twice at hsw_fdi_link_train Now with Daniel Vetter's suggestion to use "/2" instead of ">>1". Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> [danvet: Applied tiny bikesheds: - mention in comment that we test each voltage/emphasis level twice - realing arguments of the only untouched reg write, it spilled over the 80 char limit ...] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2012-11-01 23:00:59 +00:00
*/
I915_WRITE(FDI_RX_MISC(PIPE_A), FDI_RX_PWRDN_LANE1_VAL(2) |
drm/i915: fix Haswell FDI link training code This commit makes hsw_fdi_link_train responsible for implementing everything described in the "Enable and train FDI" section from the Hawell CRT mode set sequence documentation. We completely rewrite hsw_fdi_link_train to match the documentation and we also call it in the right place. This patch was initially sent as a series of tiny patches fixing every little problem of the function, but since there were too many patches fixing the same function it got a little difficult to get the "big picture" of how the function would be in the end, so here we amended all the patches into a single big patch fixing the whole function. Problems we fixed: 1 - Train Haswell FDI at the right time. We need to train the FDI before enabling the pipes and planes, so we're moving the call from lpt_pch_enable to haswell_crtc_enable directly. We are also removing ironlake_fdi_pll_enable since the PLL enablement on Haswell is completely different and is also done during the link training steps. 2 - Use the right FDI_RX_CTL register on Haswell There is only one PCH transcoder, so it's always _FDI_RXA_CTL. Using "pipe" here is wrong. 3 - Don't rely on DDI_BUF_CTL previous values Just set the bits we want, everything else is zero. Also POSTING_READ the register before sleeping. 4 - Program the FDI RX TUSIZE register on hsw_fdi_link_train According to the mode set sequence documentation, this is the right place. According to the FDI_RX_TUSIZE register description, this is the value we should set. Also remove the code that sets this register from the old location: lpt_pch_enable. 5 - Properly program FDI_RX_MISC pwrdn lane values on HSW 6 - Wait only 35us for the FDI link training First we wait 30us for the FDI receiver lane calibration, then we wait 5us for the FDI auto training time. 7 - Remove an useless indentation level on hsw_fdi_link_train We already "break" when the link training succeeds. 8 - Disable FDI_RX_ENABLE, not FDI_RX_PLL_ENABLE When we fail the training. 9 - Change Haswell FDI link training error messages We shouldn't call DRM_ERROR when still looping through voltage levels since this is expected and not really a failure. So in this commit we adjust the error path to only DRM_ERROR when we really fail after trying everything. While at it, replace DRM_DEBUG_DRIVER with DRM_DEBUG_KMS since it's what we use everywhere. 10 - Try each voltage twice at hsw_fdi_link_train Now with Daniel Vetter's suggestion to use "/2" instead of ">>1". Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> [danvet: Applied tiny bikesheds: - mention in comment that we test each voltage/emphasis level twice - realing arguments of the only untouched reg write, it spilled over the 80 char limit ...] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2012-11-01 23:00:59 +00:00
FDI_RX_PWRDN_LANE0_VAL(2) |
FDI_RX_TP1_TO_TP2_48 | FDI_RX_FDI_DELAY_90);
/* Enable the PCH Receiver FDI PLL */
rx_ctl_val = dev_priv->fdi_rx_config | FDI_RX_ENHANCE_FRAME_ENABLE |
FDI_RX_PLL_ENABLE |
FDI_DP_PORT_WIDTH(crtc_state->fdi_lanes);
I915_WRITE(FDI_RX_CTL(PIPE_A), rx_ctl_val);
POSTING_READ(FDI_RX_CTL(PIPE_A));
drm/i915: fix Haswell FDI link training code This commit makes hsw_fdi_link_train responsible for implementing everything described in the "Enable and train FDI" section from the Hawell CRT mode set sequence documentation. We completely rewrite hsw_fdi_link_train to match the documentation and we also call it in the right place. This patch was initially sent as a series of tiny patches fixing every little problem of the function, but since there were too many patches fixing the same function it got a little difficult to get the "big picture" of how the function would be in the end, so here we amended all the patches into a single big patch fixing the whole function. Problems we fixed: 1 - Train Haswell FDI at the right time. We need to train the FDI before enabling the pipes and planes, so we're moving the call from lpt_pch_enable to haswell_crtc_enable directly. We are also removing ironlake_fdi_pll_enable since the PLL enablement on Haswell is completely different and is also done during the link training steps. 2 - Use the right FDI_RX_CTL register on Haswell There is only one PCH transcoder, so it's always _FDI_RXA_CTL. Using "pipe" here is wrong. 3 - Don't rely on DDI_BUF_CTL previous values Just set the bits we want, everything else is zero. Also POSTING_READ the register before sleeping. 4 - Program the FDI RX TUSIZE register on hsw_fdi_link_train According to the mode set sequence documentation, this is the right place. According to the FDI_RX_TUSIZE register description, this is the value we should set. Also remove the code that sets this register from the old location: lpt_pch_enable. 5 - Properly program FDI_RX_MISC pwrdn lane values on HSW 6 - Wait only 35us for the FDI link training First we wait 30us for the FDI receiver lane calibration, then we wait 5us for the FDI auto training time. 7 - Remove an useless indentation level on hsw_fdi_link_train We already "break" when the link training succeeds. 8 - Disable FDI_RX_ENABLE, not FDI_RX_PLL_ENABLE When we fail the training. 9 - Change Haswell FDI link training error messages We shouldn't call DRM_ERROR when still looping through voltage levels since this is expected and not really a failure. So in this commit we adjust the error path to only DRM_ERROR when we really fail after trying everything. While at it, replace DRM_DEBUG_DRIVER with DRM_DEBUG_KMS since it's what we use everywhere. 10 - Try each voltage twice at hsw_fdi_link_train Now with Daniel Vetter's suggestion to use "/2" instead of ">>1". Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> [danvet: Applied tiny bikesheds: - mention in comment that we test each voltage/emphasis level twice - realing arguments of the only untouched reg write, it spilled over the 80 char limit ...] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2012-11-01 23:00:59 +00:00
udelay(220);
/* Switch from Rawclk to PCDclk */
rx_ctl_val |= FDI_PCDCLK;
I915_WRITE(FDI_RX_CTL(PIPE_A), rx_ctl_val);
drm/i915: fix Haswell FDI link training code This commit makes hsw_fdi_link_train responsible for implementing everything described in the "Enable and train FDI" section from the Hawell CRT mode set sequence documentation. We completely rewrite hsw_fdi_link_train to match the documentation and we also call it in the right place. This patch was initially sent as a series of tiny patches fixing every little problem of the function, but since there were too many patches fixing the same function it got a little difficult to get the "big picture" of how the function would be in the end, so here we amended all the patches into a single big patch fixing the whole function. Problems we fixed: 1 - Train Haswell FDI at the right time. We need to train the FDI before enabling the pipes and planes, so we're moving the call from lpt_pch_enable to haswell_crtc_enable directly. We are also removing ironlake_fdi_pll_enable since the PLL enablement on Haswell is completely different and is also done during the link training steps. 2 - Use the right FDI_RX_CTL register on Haswell There is only one PCH transcoder, so it's always _FDI_RXA_CTL. Using "pipe" here is wrong. 3 - Don't rely on DDI_BUF_CTL previous values Just set the bits we want, everything else is zero. Also POSTING_READ the register before sleeping. 4 - Program the FDI RX TUSIZE register on hsw_fdi_link_train According to the mode set sequence documentation, this is the right place. According to the FDI_RX_TUSIZE register description, this is the value we should set. Also remove the code that sets this register from the old location: lpt_pch_enable. 5 - Properly program FDI_RX_MISC pwrdn lane values on HSW 6 - Wait only 35us for the FDI link training First we wait 30us for the FDI receiver lane calibration, then we wait 5us for the FDI auto training time. 7 - Remove an useless indentation level on hsw_fdi_link_train We already "break" when the link training succeeds. 8 - Disable FDI_RX_ENABLE, not FDI_RX_PLL_ENABLE When we fail the training. 9 - Change Haswell FDI link training error messages We shouldn't call DRM_ERROR when still looping through voltage levels since this is expected and not really a failure. So in this commit we adjust the error path to only DRM_ERROR when we really fail after trying everything. While at it, replace DRM_DEBUG_DRIVER with DRM_DEBUG_KMS since it's what we use everywhere. 10 - Try each voltage twice at hsw_fdi_link_train Now with Daniel Vetter's suggestion to use "/2" instead of ">>1". Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> [danvet: Applied tiny bikesheds: - mention in comment that we test each voltage/emphasis level twice - realing arguments of the only untouched reg write, it spilled over the 80 char limit ...] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2012-11-01 23:00:59 +00:00
/* Configure Port Clock Select */
ddi_pll_sel = hsw_pll_to_ddi_pll_sel(crtc_state->shared_dpll);
I915_WRITE(PORT_CLK_SEL(PORT_E), ddi_pll_sel);
WARN_ON(ddi_pll_sel != PORT_CLK_SEL_SPLL);
drm/i915: fix Haswell FDI link training code This commit makes hsw_fdi_link_train responsible for implementing everything described in the "Enable and train FDI" section from the Hawell CRT mode set sequence documentation. We completely rewrite hsw_fdi_link_train to match the documentation and we also call it in the right place. This patch was initially sent as a series of tiny patches fixing every little problem of the function, but since there were too many patches fixing the same function it got a little difficult to get the "big picture" of how the function would be in the end, so here we amended all the patches into a single big patch fixing the whole function. Problems we fixed: 1 - Train Haswell FDI at the right time. We need to train the FDI before enabling the pipes and planes, so we're moving the call from lpt_pch_enable to haswell_crtc_enable directly. We are also removing ironlake_fdi_pll_enable since the PLL enablement on Haswell is completely different and is also done during the link training steps. 2 - Use the right FDI_RX_CTL register on Haswell There is only one PCH transcoder, so it's always _FDI_RXA_CTL. Using "pipe" here is wrong. 3 - Don't rely on DDI_BUF_CTL previous values Just set the bits we want, everything else is zero. Also POSTING_READ the register before sleeping. 4 - Program the FDI RX TUSIZE register on hsw_fdi_link_train According to the mode set sequence documentation, this is the right place. According to the FDI_RX_TUSIZE register description, this is the value we should set. Also remove the code that sets this register from the old location: lpt_pch_enable. 5 - Properly program FDI_RX_MISC pwrdn lane values on HSW 6 - Wait only 35us for the FDI link training First we wait 30us for the FDI receiver lane calibration, then we wait 5us for the FDI auto training time. 7 - Remove an useless indentation level on hsw_fdi_link_train We already "break" when the link training succeeds. 8 - Disable FDI_RX_ENABLE, not FDI_RX_PLL_ENABLE When we fail the training. 9 - Change Haswell FDI link training error messages We shouldn't call DRM_ERROR when still looping through voltage levels since this is expected and not really a failure. So in this commit we adjust the error path to only DRM_ERROR when we really fail after trying everything. While at it, replace DRM_DEBUG_DRIVER with DRM_DEBUG_KMS since it's what we use everywhere. 10 - Try each voltage twice at hsw_fdi_link_train Now with Daniel Vetter's suggestion to use "/2" instead of ">>1". Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> [danvet: Applied tiny bikesheds: - mention in comment that we test each voltage/emphasis level twice - realing arguments of the only untouched reg write, it spilled over the 80 char limit ...] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2012-11-01 23:00:59 +00:00
/* Start the training iterating through available voltages and emphasis,
* testing each value twice. */
for (i = 0; i < ARRAY_SIZE(hsw_ddi_translations_fdi) * 2; i++) {
/* Configure DP_TP_CTL with auto-training */
I915_WRITE(DP_TP_CTL(PORT_E),
DP_TP_CTL_FDI_AUTOTRAIN |
DP_TP_CTL_ENHANCED_FRAME_ENABLE |
DP_TP_CTL_LINK_TRAIN_PAT1 |
DP_TP_CTL_ENABLE);
/* Configure and enable DDI_BUF_CTL for DDI E with next voltage.
* DDI E does not support port reversal, the functionality is
* achieved on the PCH side in FDI_RX_CTL, so no need to set the
* port reversal bit */
I915_WRITE(DDI_BUF_CTL(PORT_E),
drm/i915: fix Haswell FDI link training code This commit makes hsw_fdi_link_train responsible for implementing everything described in the "Enable and train FDI" section from the Hawell CRT mode set sequence documentation. We completely rewrite hsw_fdi_link_train to match the documentation and we also call it in the right place. This patch was initially sent as a series of tiny patches fixing every little problem of the function, but since there were too many patches fixing the same function it got a little difficult to get the "big picture" of how the function would be in the end, so here we amended all the patches into a single big patch fixing the whole function. Problems we fixed: 1 - Train Haswell FDI at the right time. We need to train the FDI before enabling the pipes and planes, so we're moving the call from lpt_pch_enable to haswell_crtc_enable directly. We are also removing ironlake_fdi_pll_enable since the PLL enablement on Haswell is completely different and is also done during the link training steps. 2 - Use the right FDI_RX_CTL register on Haswell There is only one PCH transcoder, so it's always _FDI_RXA_CTL. Using "pipe" here is wrong. 3 - Don't rely on DDI_BUF_CTL previous values Just set the bits we want, everything else is zero. Also POSTING_READ the register before sleeping. 4 - Program the FDI RX TUSIZE register on hsw_fdi_link_train According to the mode set sequence documentation, this is the right place. According to the FDI_RX_TUSIZE register description, this is the value we should set. Also remove the code that sets this register from the old location: lpt_pch_enable. 5 - Properly program FDI_RX_MISC pwrdn lane values on HSW 6 - Wait only 35us for the FDI link training First we wait 30us for the FDI receiver lane calibration, then we wait 5us for the FDI auto training time. 7 - Remove an useless indentation level on hsw_fdi_link_train We already "break" when the link training succeeds. 8 - Disable FDI_RX_ENABLE, not FDI_RX_PLL_ENABLE When we fail the training. 9 - Change Haswell FDI link training error messages We shouldn't call DRM_ERROR when still looping through voltage levels since this is expected and not really a failure. So in this commit we adjust the error path to only DRM_ERROR when we really fail after trying everything. While at it, replace DRM_DEBUG_DRIVER with DRM_DEBUG_KMS since it's what we use everywhere. 10 - Try each voltage twice at hsw_fdi_link_train Now with Daniel Vetter's suggestion to use "/2" instead of ">>1". Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> [danvet: Applied tiny bikesheds: - mention in comment that we test each voltage/emphasis level twice - realing arguments of the only untouched reg write, it spilled over the 80 char limit ...] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2012-11-01 23:00:59 +00:00
DDI_BUF_CTL_ENABLE |
((crtc_state->fdi_lanes - 1) << 1) |
DDI_BUF_TRANS_SELECT(i / 2));
drm/i915: fix Haswell FDI link training code This commit makes hsw_fdi_link_train responsible for implementing everything described in the "Enable and train FDI" section from the Hawell CRT mode set sequence documentation. We completely rewrite hsw_fdi_link_train to match the documentation and we also call it in the right place. This patch was initially sent as a series of tiny patches fixing every little problem of the function, but since there were too many patches fixing the same function it got a little difficult to get the "big picture" of how the function would be in the end, so here we amended all the patches into a single big patch fixing the whole function. Problems we fixed: 1 - Train Haswell FDI at the right time. We need to train the FDI before enabling the pipes and planes, so we're moving the call from lpt_pch_enable to haswell_crtc_enable directly. We are also removing ironlake_fdi_pll_enable since the PLL enablement on Haswell is completely different and is also done during the link training steps. 2 - Use the right FDI_RX_CTL register on Haswell There is only one PCH transcoder, so it's always _FDI_RXA_CTL. Using "pipe" here is wrong. 3 - Don't rely on DDI_BUF_CTL previous values Just set the bits we want, everything else is zero. Also POSTING_READ the register before sleeping. 4 - Program the FDI RX TUSIZE register on hsw_fdi_link_train According to the mode set sequence documentation, this is the right place. According to the FDI_RX_TUSIZE register description, this is the value we should set. Also remove the code that sets this register from the old location: lpt_pch_enable. 5 - Properly program FDI_RX_MISC pwrdn lane values on HSW 6 - Wait only 35us for the FDI link training First we wait 30us for the FDI receiver lane calibration, then we wait 5us for the FDI auto training time. 7 - Remove an useless indentation level on hsw_fdi_link_train We already "break" when the link training succeeds. 8 - Disable FDI_RX_ENABLE, not FDI_RX_PLL_ENABLE When we fail the training. 9 - Change Haswell FDI link training error messages We shouldn't call DRM_ERROR when still looping through voltage levels since this is expected and not really a failure. So in this commit we adjust the error path to only DRM_ERROR when we really fail after trying everything. While at it, replace DRM_DEBUG_DRIVER with DRM_DEBUG_KMS since it's what we use everywhere. 10 - Try each voltage twice at hsw_fdi_link_train Now with Daniel Vetter's suggestion to use "/2" instead of ">>1". Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> [danvet: Applied tiny bikesheds: - mention in comment that we test each voltage/emphasis level twice - realing arguments of the only untouched reg write, it spilled over the 80 char limit ...] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2012-11-01 23:00:59 +00:00
POSTING_READ(DDI_BUF_CTL(PORT_E));
udelay(600);
drm/i915: fix Haswell FDI link training code This commit makes hsw_fdi_link_train responsible for implementing everything described in the "Enable and train FDI" section from the Hawell CRT mode set sequence documentation. We completely rewrite hsw_fdi_link_train to match the documentation and we also call it in the right place. This patch was initially sent as a series of tiny patches fixing every little problem of the function, but since there were too many patches fixing the same function it got a little difficult to get the "big picture" of how the function would be in the end, so here we amended all the patches into a single big patch fixing the whole function. Problems we fixed: 1 - Train Haswell FDI at the right time. We need to train the FDI before enabling the pipes and planes, so we're moving the call from lpt_pch_enable to haswell_crtc_enable directly. We are also removing ironlake_fdi_pll_enable since the PLL enablement on Haswell is completely different and is also done during the link training steps. 2 - Use the right FDI_RX_CTL register on Haswell There is only one PCH transcoder, so it's always _FDI_RXA_CTL. Using "pipe" here is wrong. 3 - Don't rely on DDI_BUF_CTL previous values Just set the bits we want, everything else is zero. Also POSTING_READ the register before sleeping. 4 - Program the FDI RX TUSIZE register on hsw_fdi_link_train According to the mode set sequence documentation, this is the right place. According to the FDI_RX_TUSIZE register description, this is the value we should set. Also remove the code that sets this register from the old location: lpt_pch_enable. 5 - Properly program FDI_RX_MISC pwrdn lane values on HSW 6 - Wait only 35us for the FDI link training First we wait 30us for the FDI receiver lane calibration, then we wait 5us for the FDI auto training time. 7 - Remove an useless indentation level on hsw_fdi_link_train We already "break" when the link training succeeds. 8 - Disable FDI_RX_ENABLE, not FDI_RX_PLL_ENABLE When we fail the training. 9 - Change Haswell FDI link training error messages We shouldn't call DRM_ERROR when still looping through voltage levels since this is expected and not really a failure. So in this commit we adjust the error path to only DRM_ERROR when we really fail after trying everything. While at it, replace DRM_DEBUG_DRIVER with DRM_DEBUG_KMS since it's what we use everywhere. 10 - Try each voltage twice at hsw_fdi_link_train Now with Daniel Vetter's suggestion to use "/2" instead of ">>1". Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> [danvet: Applied tiny bikesheds: - mention in comment that we test each voltage/emphasis level twice - realing arguments of the only untouched reg write, it spilled over the 80 char limit ...] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2012-11-01 23:00:59 +00:00
/* Program PCH FDI Receiver TU */
I915_WRITE(FDI_RX_TUSIZE1(PIPE_A), TU_SIZE(64));
drm/i915: fix Haswell FDI link training code This commit makes hsw_fdi_link_train responsible for implementing everything described in the "Enable and train FDI" section from the Hawell CRT mode set sequence documentation. We completely rewrite hsw_fdi_link_train to match the documentation and we also call it in the right place. This patch was initially sent as a series of tiny patches fixing every little problem of the function, but since there were too many patches fixing the same function it got a little difficult to get the "big picture" of how the function would be in the end, so here we amended all the patches into a single big patch fixing the whole function. Problems we fixed: 1 - Train Haswell FDI at the right time. We need to train the FDI before enabling the pipes and planes, so we're moving the call from lpt_pch_enable to haswell_crtc_enable directly. We are also removing ironlake_fdi_pll_enable since the PLL enablement on Haswell is completely different and is also done during the link training steps. 2 - Use the right FDI_RX_CTL register on Haswell There is only one PCH transcoder, so it's always _FDI_RXA_CTL. Using "pipe" here is wrong. 3 - Don't rely on DDI_BUF_CTL previous values Just set the bits we want, everything else is zero. Also POSTING_READ the register before sleeping. 4 - Program the FDI RX TUSIZE register on hsw_fdi_link_train According to the mode set sequence documentation, this is the right place. According to the FDI_RX_TUSIZE register description, this is the value we should set. Also remove the code that sets this register from the old location: lpt_pch_enable. 5 - Properly program FDI_RX_MISC pwrdn lane values on HSW 6 - Wait only 35us for the FDI link training First we wait 30us for the FDI receiver lane calibration, then we wait 5us for the FDI auto training time. 7 - Remove an useless indentation level on hsw_fdi_link_train We already "break" when the link training succeeds. 8 - Disable FDI_RX_ENABLE, not FDI_RX_PLL_ENABLE When we fail the training. 9 - Change Haswell FDI link training error messages We shouldn't call DRM_ERROR when still looping through voltage levels since this is expected and not really a failure. So in this commit we adjust the error path to only DRM_ERROR when we really fail after trying everything. While at it, replace DRM_DEBUG_DRIVER with DRM_DEBUG_KMS since it's what we use everywhere. 10 - Try each voltage twice at hsw_fdi_link_train Now with Daniel Vetter's suggestion to use "/2" instead of ">>1". Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> [danvet: Applied tiny bikesheds: - mention in comment that we test each voltage/emphasis level twice - realing arguments of the only untouched reg write, it spilled over the 80 char limit ...] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2012-11-01 23:00:59 +00:00
/* Enable PCH FDI Receiver with auto-training */
rx_ctl_val |= FDI_RX_ENABLE | FDI_LINK_TRAIN_AUTO;
I915_WRITE(FDI_RX_CTL(PIPE_A), rx_ctl_val);
POSTING_READ(FDI_RX_CTL(PIPE_A));
drm/i915: fix Haswell FDI link training code This commit makes hsw_fdi_link_train responsible for implementing everything described in the "Enable and train FDI" section from the Hawell CRT mode set sequence documentation. We completely rewrite hsw_fdi_link_train to match the documentation and we also call it in the right place. This patch was initially sent as a series of tiny patches fixing every little problem of the function, but since there were too many patches fixing the same function it got a little difficult to get the "big picture" of how the function would be in the end, so here we amended all the patches into a single big patch fixing the whole function. Problems we fixed: 1 - Train Haswell FDI at the right time. We need to train the FDI before enabling the pipes and planes, so we're moving the call from lpt_pch_enable to haswell_crtc_enable directly. We are also removing ironlake_fdi_pll_enable since the PLL enablement on Haswell is completely different and is also done during the link training steps. 2 - Use the right FDI_RX_CTL register on Haswell There is only one PCH transcoder, so it's always _FDI_RXA_CTL. Using "pipe" here is wrong. 3 - Don't rely on DDI_BUF_CTL previous values Just set the bits we want, everything else is zero. Also POSTING_READ the register before sleeping. 4 - Program the FDI RX TUSIZE register on hsw_fdi_link_train According to the mode set sequence documentation, this is the right place. According to the FDI_RX_TUSIZE register description, this is the value we should set. Also remove the code that sets this register from the old location: lpt_pch_enable. 5 - Properly program FDI_RX_MISC pwrdn lane values on HSW 6 - Wait only 35us for the FDI link training First we wait 30us for the FDI receiver lane calibration, then we wait 5us for the FDI auto training time. 7 - Remove an useless indentation level on hsw_fdi_link_train We already "break" when the link training succeeds. 8 - Disable FDI_RX_ENABLE, not FDI_RX_PLL_ENABLE When we fail the training. 9 - Change Haswell FDI link training error messages We shouldn't call DRM_ERROR when still looping through voltage levels since this is expected and not really a failure. So in this commit we adjust the error path to only DRM_ERROR when we really fail after trying everything. While at it, replace DRM_DEBUG_DRIVER with DRM_DEBUG_KMS since it's what we use everywhere. 10 - Try each voltage twice at hsw_fdi_link_train Now with Daniel Vetter's suggestion to use "/2" instead of ">>1". Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> [danvet: Applied tiny bikesheds: - mention in comment that we test each voltage/emphasis level twice - realing arguments of the only untouched reg write, it spilled over the 80 char limit ...] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2012-11-01 23:00:59 +00:00
/* Wait for FDI receiver lane calibration */
udelay(30);
/* Unset FDI_RX_MISC pwrdn lanes */
temp = I915_READ(FDI_RX_MISC(PIPE_A));
drm/i915: fix Haswell FDI link training code This commit makes hsw_fdi_link_train responsible for implementing everything described in the "Enable and train FDI" section from the Hawell CRT mode set sequence documentation. We completely rewrite hsw_fdi_link_train to match the documentation and we also call it in the right place. This patch was initially sent as a series of tiny patches fixing every little problem of the function, but since there were too many patches fixing the same function it got a little difficult to get the "big picture" of how the function would be in the end, so here we amended all the patches into a single big patch fixing the whole function. Problems we fixed: 1 - Train Haswell FDI at the right time. We need to train the FDI before enabling the pipes and planes, so we're moving the call from lpt_pch_enable to haswell_crtc_enable directly. We are also removing ironlake_fdi_pll_enable since the PLL enablement on Haswell is completely different and is also done during the link training steps. 2 - Use the right FDI_RX_CTL register on Haswell There is only one PCH transcoder, so it's always _FDI_RXA_CTL. Using "pipe" here is wrong. 3 - Don't rely on DDI_BUF_CTL previous values Just set the bits we want, everything else is zero. Also POSTING_READ the register before sleeping. 4 - Program the FDI RX TUSIZE register on hsw_fdi_link_train According to the mode set sequence documentation, this is the right place. According to the FDI_RX_TUSIZE register description, this is the value we should set. Also remove the code that sets this register from the old location: lpt_pch_enable. 5 - Properly program FDI_RX_MISC pwrdn lane values on HSW 6 - Wait only 35us for the FDI link training First we wait 30us for the FDI receiver lane calibration, then we wait 5us for the FDI auto training time. 7 - Remove an useless indentation level on hsw_fdi_link_train We already "break" when the link training succeeds. 8 - Disable FDI_RX_ENABLE, not FDI_RX_PLL_ENABLE When we fail the training. 9 - Change Haswell FDI link training error messages We shouldn't call DRM_ERROR when still looping through voltage levels since this is expected and not really a failure. So in this commit we adjust the error path to only DRM_ERROR when we really fail after trying everything. While at it, replace DRM_DEBUG_DRIVER with DRM_DEBUG_KMS since it's what we use everywhere. 10 - Try each voltage twice at hsw_fdi_link_train Now with Daniel Vetter's suggestion to use "/2" instead of ">>1". Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> [danvet: Applied tiny bikesheds: - mention in comment that we test each voltage/emphasis level twice - realing arguments of the only untouched reg write, it spilled over the 80 char limit ...] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2012-11-01 23:00:59 +00:00
temp &= ~(FDI_RX_PWRDN_LANE1_MASK | FDI_RX_PWRDN_LANE0_MASK);
I915_WRITE(FDI_RX_MISC(PIPE_A), temp);
POSTING_READ(FDI_RX_MISC(PIPE_A));
drm/i915: fix Haswell FDI link training code This commit makes hsw_fdi_link_train responsible for implementing everything described in the "Enable and train FDI" section from the Hawell CRT mode set sequence documentation. We completely rewrite hsw_fdi_link_train to match the documentation and we also call it in the right place. This patch was initially sent as a series of tiny patches fixing every little problem of the function, but since there were too many patches fixing the same function it got a little difficult to get the "big picture" of how the function would be in the end, so here we amended all the patches into a single big patch fixing the whole function. Problems we fixed: 1 - Train Haswell FDI at the right time. We need to train the FDI before enabling the pipes and planes, so we're moving the call from lpt_pch_enable to haswell_crtc_enable directly. We are also removing ironlake_fdi_pll_enable since the PLL enablement on Haswell is completely different and is also done during the link training steps. 2 - Use the right FDI_RX_CTL register on Haswell There is only one PCH transcoder, so it's always _FDI_RXA_CTL. Using "pipe" here is wrong. 3 - Don't rely on DDI_BUF_CTL previous values Just set the bits we want, everything else is zero. Also POSTING_READ the register before sleeping. 4 - Program the FDI RX TUSIZE register on hsw_fdi_link_train According to the mode set sequence documentation, this is the right place. According to the FDI_RX_TUSIZE register description, this is the value we should set. Also remove the code that sets this register from the old location: lpt_pch_enable. 5 - Properly program FDI_RX_MISC pwrdn lane values on HSW 6 - Wait only 35us for the FDI link training First we wait 30us for the FDI receiver lane calibration, then we wait 5us for the FDI auto training time. 7 - Remove an useless indentation level on hsw_fdi_link_train We already "break" when the link training succeeds. 8 - Disable FDI_RX_ENABLE, not FDI_RX_PLL_ENABLE When we fail the training. 9 - Change Haswell FDI link training error messages We shouldn't call DRM_ERROR when still looping through voltage levels since this is expected and not really a failure. So in this commit we adjust the error path to only DRM_ERROR when we really fail after trying everything. While at it, replace DRM_DEBUG_DRIVER with DRM_DEBUG_KMS since it's what we use everywhere. 10 - Try each voltage twice at hsw_fdi_link_train Now with Daniel Vetter's suggestion to use "/2" instead of ">>1". Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> [danvet: Applied tiny bikesheds: - mention in comment that we test each voltage/emphasis level twice - realing arguments of the only untouched reg write, it spilled over the 80 char limit ...] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2012-11-01 23:00:59 +00:00
/* Wait for FDI auto training time */
udelay(5);
temp = I915_READ(DP_TP_STATUS(PORT_E));
if (temp & DP_TP_STATUS_AUTOTRAIN_DONE) {
drm/i915: fix Haswell FDI link training code This commit makes hsw_fdi_link_train responsible for implementing everything described in the "Enable and train FDI" section from the Hawell CRT mode set sequence documentation. We completely rewrite hsw_fdi_link_train to match the documentation and we also call it in the right place. This patch was initially sent as a series of tiny patches fixing every little problem of the function, but since there were too many patches fixing the same function it got a little difficult to get the "big picture" of how the function would be in the end, so here we amended all the patches into a single big patch fixing the whole function. Problems we fixed: 1 - Train Haswell FDI at the right time. We need to train the FDI before enabling the pipes and planes, so we're moving the call from lpt_pch_enable to haswell_crtc_enable directly. We are also removing ironlake_fdi_pll_enable since the PLL enablement on Haswell is completely different and is also done during the link training steps. 2 - Use the right FDI_RX_CTL register on Haswell There is only one PCH transcoder, so it's always _FDI_RXA_CTL. Using "pipe" here is wrong. 3 - Don't rely on DDI_BUF_CTL previous values Just set the bits we want, everything else is zero. Also POSTING_READ the register before sleeping. 4 - Program the FDI RX TUSIZE register on hsw_fdi_link_train According to the mode set sequence documentation, this is the right place. According to the FDI_RX_TUSIZE register description, this is the value we should set. Also remove the code that sets this register from the old location: lpt_pch_enable. 5 - Properly program FDI_RX_MISC pwrdn lane values on HSW 6 - Wait only 35us for the FDI link training First we wait 30us for the FDI receiver lane calibration, then we wait 5us for the FDI auto training time. 7 - Remove an useless indentation level on hsw_fdi_link_train We already "break" when the link training succeeds. 8 - Disable FDI_RX_ENABLE, not FDI_RX_PLL_ENABLE When we fail the training. 9 - Change Haswell FDI link training error messages We shouldn't call DRM_ERROR when still looping through voltage levels since this is expected and not really a failure. So in this commit we adjust the error path to only DRM_ERROR when we really fail after trying everything. While at it, replace DRM_DEBUG_DRIVER with DRM_DEBUG_KMS since it's what we use everywhere. 10 - Try each voltage twice at hsw_fdi_link_train Now with Daniel Vetter's suggestion to use "/2" instead of ">>1". Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> [danvet: Applied tiny bikesheds: - mention in comment that we test each voltage/emphasis level twice - realing arguments of the only untouched reg write, it spilled over the 80 char limit ...] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2012-11-01 23:00:59 +00:00
DRM_DEBUG_KMS("FDI link training done on step %d\n", i);
break;
}
/*
* Leave things enabled even if we failed to train FDI.
* Results in less fireworks from the state checker.
*/
if (i == ARRAY_SIZE(hsw_ddi_translations_fdi) * 2 - 1) {
DRM_ERROR("FDI link training failed!\n");
break;
}
drm/i915: fix Haswell FDI link training code This commit makes hsw_fdi_link_train responsible for implementing everything described in the "Enable and train FDI" section from the Hawell CRT mode set sequence documentation. We completely rewrite hsw_fdi_link_train to match the documentation and we also call it in the right place. This patch was initially sent as a series of tiny patches fixing every little problem of the function, but since there were too many patches fixing the same function it got a little difficult to get the "big picture" of how the function would be in the end, so here we amended all the patches into a single big patch fixing the whole function. Problems we fixed: 1 - Train Haswell FDI at the right time. We need to train the FDI before enabling the pipes and planes, so we're moving the call from lpt_pch_enable to haswell_crtc_enable directly. We are also removing ironlake_fdi_pll_enable since the PLL enablement on Haswell is completely different and is also done during the link training steps. 2 - Use the right FDI_RX_CTL register on Haswell There is only one PCH transcoder, so it's always _FDI_RXA_CTL. Using "pipe" here is wrong. 3 - Don't rely on DDI_BUF_CTL previous values Just set the bits we want, everything else is zero. Also POSTING_READ the register before sleeping. 4 - Program the FDI RX TUSIZE register on hsw_fdi_link_train According to the mode set sequence documentation, this is the right place. According to the FDI_RX_TUSIZE register description, this is the value we should set. Also remove the code that sets this register from the old location: lpt_pch_enable. 5 - Properly program FDI_RX_MISC pwrdn lane values on HSW 6 - Wait only 35us for the FDI link training First we wait 30us for the FDI receiver lane calibration, then we wait 5us for the FDI auto training time. 7 - Remove an useless indentation level on hsw_fdi_link_train We already "break" when the link training succeeds. 8 - Disable FDI_RX_ENABLE, not FDI_RX_PLL_ENABLE When we fail the training. 9 - Change Haswell FDI link training error messages We shouldn't call DRM_ERROR when still looping through voltage levels since this is expected and not really a failure. So in this commit we adjust the error path to only DRM_ERROR when we really fail after trying everything. While at it, replace DRM_DEBUG_DRIVER with DRM_DEBUG_KMS since it's what we use everywhere. 10 - Try each voltage twice at hsw_fdi_link_train Now with Daniel Vetter's suggestion to use "/2" instead of ">>1". Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> [danvet: Applied tiny bikesheds: - mention in comment that we test each voltage/emphasis level twice - realing arguments of the only untouched reg write, it spilled over the 80 char limit ...] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2012-11-01 23:00:59 +00:00
drm/i915: Disable FDI RX before DDI_BUF_CTL Bspec is confused w.r.t. the HSW/BDW FDI disable sequence. It lists FDI RX disable both as step 13 and step 18 in the sequence. But I dug up an old BUN mail from Art that moved the FDI RX disable to happen before DDI_BUF_CTL disable. That BUN did not renumber the steps and just added a note: "Workaround: Disable PCH FDI Receiver before disabling DDI_BUF_CTL." The BUN described the symptoms of the fixed issue as: "PCH display underflow and a black screen on the analog CRT port that happened after a FDI re-train" I suppose later someone tried to renumber the steps to match, but forgot to remove the FDI RX disable from its old position in the sequence. They also forgot to update the note describing what should be done in case of an FDI training failure. Currently it says: "To retry FDI training, follow the Disable Sequence steps to Disable FDI, but skip the steps related to clocks and PLLs (16, 19, and 20), ..." It should really say "17, 20, and 21" with the current sequence because those are the steps that deal with PLLs and whatnot, after step 13 became FDI RX disable. And had the step 18 FDI RX disable been removed, as I suspect it should have, the note should actually say "17, 19, and 20". So, let's move the FDI RX disable to happen before DDI_BUF_CTL disable, as that would appear to be the correct order based on the BUN. Note that Art has since unconfused the spec, and so this patch should now match the steps listed in the spec. v2: Add a note that the spec is now correct Cc: Paulo Zanoni <przanoni@gmail.com> Cc: Art Runyan <arthur.j.runyan@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1456841783-4779-1-git-send-email-ville.syrjala@linux.intel.com Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
2016-03-01 14:16:23 +00:00
rx_ctl_val &= ~FDI_RX_ENABLE;
I915_WRITE(FDI_RX_CTL(PIPE_A), rx_ctl_val);
POSTING_READ(FDI_RX_CTL(PIPE_A));
temp = I915_READ(DDI_BUF_CTL(PORT_E));
temp &= ~DDI_BUF_CTL_ENABLE;
I915_WRITE(DDI_BUF_CTL(PORT_E), temp);
POSTING_READ(DDI_BUF_CTL(PORT_E));
drm/i915: fix Haswell FDI link training code This commit makes hsw_fdi_link_train responsible for implementing everything described in the "Enable and train FDI" section from the Hawell CRT mode set sequence documentation. We completely rewrite hsw_fdi_link_train to match the documentation and we also call it in the right place. This patch was initially sent as a series of tiny patches fixing every little problem of the function, but since there were too many patches fixing the same function it got a little difficult to get the "big picture" of how the function would be in the end, so here we amended all the patches into a single big patch fixing the whole function. Problems we fixed: 1 - Train Haswell FDI at the right time. We need to train the FDI before enabling the pipes and planes, so we're moving the call from lpt_pch_enable to haswell_crtc_enable directly. We are also removing ironlake_fdi_pll_enable since the PLL enablement on Haswell is completely different and is also done during the link training steps. 2 - Use the right FDI_RX_CTL register on Haswell There is only one PCH transcoder, so it's always _FDI_RXA_CTL. Using "pipe" here is wrong. 3 - Don't rely on DDI_BUF_CTL previous values Just set the bits we want, everything else is zero. Also POSTING_READ the register before sleeping. 4 - Program the FDI RX TUSIZE register on hsw_fdi_link_train According to the mode set sequence documentation, this is the right place. According to the FDI_RX_TUSIZE register description, this is the value we should set. Also remove the code that sets this register from the old location: lpt_pch_enable. 5 - Properly program FDI_RX_MISC pwrdn lane values on HSW 6 - Wait only 35us for the FDI link training First we wait 30us for the FDI receiver lane calibration, then we wait 5us for the FDI auto training time. 7 - Remove an useless indentation level on hsw_fdi_link_train We already "break" when the link training succeeds. 8 - Disable FDI_RX_ENABLE, not FDI_RX_PLL_ENABLE When we fail the training. 9 - Change Haswell FDI link training error messages We shouldn't call DRM_ERROR when still looping through voltage levels since this is expected and not really a failure. So in this commit we adjust the error path to only DRM_ERROR when we really fail after trying everything. While at it, replace DRM_DEBUG_DRIVER with DRM_DEBUG_KMS since it's what we use everywhere. 10 - Try each voltage twice at hsw_fdi_link_train Now with Daniel Vetter's suggestion to use "/2" instead of ">>1". Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> [danvet: Applied tiny bikesheds: - mention in comment that we test each voltage/emphasis level twice - realing arguments of the only untouched reg write, it spilled over the 80 char limit ...] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2012-11-01 23:00:59 +00:00
/* Disable DP_TP_CTL and FDI_RX_CTL and retry */
temp = I915_READ(DP_TP_CTL(PORT_E));
temp &= ~(DP_TP_CTL_ENABLE | DP_TP_CTL_LINK_TRAIN_MASK);
temp |= DP_TP_CTL_LINK_TRAIN_PAT1;
I915_WRITE(DP_TP_CTL(PORT_E), temp);
POSTING_READ(DP_TP_CTL(PORT_E));
intel_wait_ddi_buf_idle(dev_priv, PORT_E);
drm/i915: fix Haswell FDI link training code This commit makes hsw_fdi_link_train responsible for implementing everything described in the "Enable and train FDI" section from the Hawell CRT mode set sequence documentation. We completely rewrite hsw_fdi_link_train to match the documentation and we also call it in the right place. This patch was initially sent as a series of tiny patches fixing every little problem of the function, but since there were too many patches fixing the same function it got a little difficult to get the "big picture" of how the function would be in the end, so here we amended all the patches into a single big patch fixing the whole function. Problems we fixed: 1 - Train Haswell FDI at the right time. We need to train the FDI before enabling the pipes and planes, so we're moving the call from lpt_pch_enable to haswell_crtc_enable directly. We are also removing ironlake_fdi_pll_enable since the PLL enablement on Haswell is completely different and is also done during the link training steps. 2 - Use the right FDI_RX_CTL register on Haswell There is only one PCH transcoder, so it's always _FDI_RXA_CTL. Using "pipe" here is wrong. 3 - Don't rely on DDI_BUF_CTL previous values Just set the bits we want, everything else is zero. Also POSTING_READ the register before sleeping. 4 - Program the FDI RX TUSIZE register on hsw_fdi_link_train According to the mode set sequence documentation, this is the right place. According to the FDI_RX_TUSIZE register description, this is the value we should set. Also remove the code that sets this register from the old location: lpt_pch_enable. 5 - Properly program FDI_RX_MISC pwrdn lane values on HSW 6 - Wait only 35us for the FDI link training First we wait 30us for the FDI receiver lane calibration, then we wait 5us for the FDI auto training time. 7 - Remove an useless indentation level on hsw_fdi_link_train We already "break" when the link training succeeds. 8 - Disable FDI_RX_ENABLE, not FDI_RX_PLL_ENABLE When we fail the training. 9 - Change Haswell FDI link training error messages We shouldn't call DRM_ERROR when still looping through voltage levels since this is expected and not really a failure. So in this commit we adjust the error path to only DRM_ERROR when we really fail after trying everything. While at it, replace DRM_DEBUG_DRIVER with DRM_DEBUG_KMS since it's what we use everywhere. 10 - Try each voltage twice at hsw_fdi_link_train Now with Daniel Vetter's suggestion to use "/2" instead of ">>1". Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> [danvet: Applied tiny bikesheds: - mention in comment that we test each voltage/emphasis level twice - realing arguments of the only untouched reg write, it spilled over the 80 char limit ...] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2012-11-01 23:00:59 +00:00
/* Reset FDI_RX_MISC pwrdn lanes */
temp = I915_READ(FDI_RX_MISC(PIPE_A));
drm/i915: fix Haswell FDI link training code This commit makes hsw_fdi_link_train responsible for implementing everything described in the "Enable and train FDI" section from the Hawell CRT mode set sequence documentation. We completely rewrite hsw_fdi_link_train to match the documentation and we also call it in the right place. This patch was initially sent as a series of tiny patches fixing every little problem of the function, but since there were too many patches fixing the same function it got a little difficult to get the "big picture" of how the function would be in the end, so here we amended all the patches into a single big patch fixing the whole function. Problems we fixed: 1 - Train Haswell FDI at the right time. We need to train the FDI before enabling the pipes and planes, so we're moving the call from lpt_pch_enable to haswell_crtc_enable directly. We are also removing ironlake_fdi_pll_enable since the PLL enablement on Haswell is completely different and is also done during the link training steps. 2 - Use the right FDI_RX_CTL register on Haswell There is only one PCH transcoder, so it's always _FDI_RXA_CTL. Using "pipe" here is wrong. 3 - Don't rely on DDI_BUF_CTL previous values Just set the bits we want, everything else is zero. Also POSTING_READ the register before sleeping. 4 - Program the FDI RX TUSIZE register on hsw_fdi_link_train According to the mode set sequence documentation, this is the right place. According to the FDI_RX_TUSIZE register description, this is the value we should set. Also remove the code that sets this register from the old location: lpt_pch_enable. 5 - Properly program FDI_RX_MISC pwrdn lane values on HSW 6 - Wait only 35us for the FDI link training First we wait 30us for the FDI receiver lane calibration, then we wait 5us for the FDI auto training time. 7 - Remove an useless indentation level on hsw_fdi_link_train We already "break" when the link training succeeds. 8 - Disable FDI_RX_ENABLE, not FDI_RX_PLL_ENABLE When we fail the training. 9 - Change Haswell FDI link training error messages We shouldn't call DRM_ERROR when still looping through voltage levels since this is expected and not really a failure. So in this commit we adjust the error path to only DRM_ERROR when we really fail after trying everything. While at it, replace DRM_DEBUG_DRIVER with DRM_DEBUG_KMS since it's what we use everywhere. 10 - Try each voltage twice at hsw_fdi_link_train Now with Daniel Vetter's suggestion to use "/2" instead of ">>1". Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> [danvet: Applied tiny bikesheds: - mention in comment that we test each voltage/emphasis level twice - realing arguments of the only untouched reg write, it spilled over the 80 char limit ...] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2012-11-01 23:00:59 +00:00
temp &= ~(FDI_RX_PWRDN_LANE1_MASK | FDI_RX_PWRDN_LANE0_MASK);
temp |= FDI_RX_PWRDN_LANE1_VAL(2) | FDI_RX_PWRDN_LANE0_VAL(2);
I915_WRITE(FDI_RX_MISC(PIPE_A), temp);
POSTING_READ(FDI_RX_MISC(PIPE_A));
}
/* Enable normal pixel sending for FDI */
I915_WRITE(DP_TP_CTL(PORT_E),
DP_TP_CTL_FDI_AUTOTRAIN |
DP_TP_CTL_LINK_TRAIN_NORMAL |
DP_TP_CTL_ENHANCED_FRAME_ENABLE |
DP_TP_CTL_ENABLE);
}
static void intel_ddi_init_dp_buf_reg(struct intel_encoder *encoder)
{
struct intel_dp *intel_dp = enc_to_intel_dp(&encoder->base);
struct intel_digital_port *intel_dig_port =
enc_to_dig_port(&encoder->base);
intel_dp->DP = intel_dig_port->saved_port_bits |
DDI_BUF_CTL_ENABLE | DDI_BUF_TRANS_SELECT(0);
intel_dp->DP |= DDI_PORT_WIDTH(intel_dp->lane_count);
}
static struct intel_encoder *
intel_ddi_get_crtc_encoder(struct intel_crtc *crtc)
{
struct drm_device *dev = crtc->base.dev;
struct intel_encoder *encoder, *ret = NULL;
int num_encoders = 0;
for_each_encoder_on_crtc(dev, &crtc->base, encoder) {
ret = encoder;
num_encoders++;
}
if (num_encoders != 1)
WARN(1, "%d encoders on crtc for pipe %c\n", num_encoders,
pipe_name(crtc->pipe));
BUG_ON(ret == NULL);
return ret;
}
/* Finds the only possible encoder associated with the given CRTC. */
struct intel_encoder *
intel_ddi_get_crtc_new_encoder(struct intel_crtc_state *crtc_state)
{
struct intel_crtc *crtc = to_intel_crtc(crtc_state->base.crtc);
struct intel_encoder *ret = NULL;
struct drm_atomic_state *state;
struct drm_connector *connector;
struct drm_connector_state *connector_state;
int num_encoders = 0;
int i;
state = crtc_state->base.state;
for_each_new_connector_in_state(state, connector, connector_state, i) {
if (connector_state->crtc != crtc_state->base.crtc)
continue;
ret = to_intel_encoder(connector_state->best_encoder);
num_encoders++;
}
WARN(num_encoders != 1, "%d encoders on crtc for pipe %c\n", num_encoders,
pipe_name(crtc->pipe));
BUG_ON(ret == NULL);
return ret;
}
#define LC_FREQ 2700
drm/i915: Type safe register read/write Make I915_READ and I915_WRITE more type safe by wrapping the register offset in a struct. This should eliminate most of the fumbles we've had with misplaced parens. This only takes care of normal mmio registers. We could extend the idea to other register types and define each with its own struct. That way you wouldn't be able to accidentally pass the wrong thing to a specific register access function. The gpio_reg setup is probably the ugliest thing left. But I figure I'd just leave it for now, and wait for some divine inspiration to strike before making it nice. As for the generated code, it's actually a bit better sometimes. Eg. looking at i915_irq_handler(), we can see the following change: lea 0x70024(%rdx,%rax,1),%r9d mov $0x1,%edx - movslq %r9d,%r9 - mov %r9,%rsi - mov %r9,-0x58(%rbp) - callq *0xd8(%rbx) + mov %r9d,%esi + mov %r9d,-0x48(%rbp) callq *0xd8(%rbx) So previously gcc thought the register offset might be signed and decided to sign extend it, just in case. The rest appears to be mostly just minor shuffling of instructions. v2: i915_mmio_reg_{offset,equal,valid}() helpers added s/_REG/_MMIO/ in the register defines mo more switch statements left to worry about ring_emit stuff got sorted in a prep patch cmd parser, lrc context and w/a batch buildup also in prep patch vgpu stuff cleaned up and moved to a prep patch all other unrelated changes split out v3: Rebased due to BXT DSI/BLC, MOCS, etc. v4: Rebased due to churn, s/i915_mmio_reg_t/i915_reg_t/ Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Link: http://patchwork.freedesktop.org/patch/msgid/1447853606-2751-1-git-send-email-ville.syrjala@linux.intel.com
2015-11-18 13:33:26 +00:00
static int hsw_ddi_calc_wrpll_link(struct drm_i915_private *dev_priv,
i915_reg_t reg)
{
int refclk = LC_FREQ;
int n, p, r;
u32 wrpll;
wrpll = I915_READ(reg);
switch (wrpll & WRPLL_PLL_REF_MASK) {
case WRPLL_PLL_SSC:
case WRPLL_PLL_NON_SSC:
/*
* We could calculate spread here, but our checking
* code only cares about 5% accuracy, and spread is a max of
* 0.5% downspread.
*/
refclk = 135;
break;
case WRPLL_PLL_LCPLL:
refclk = LC_FREQ;
break;
default:
WARN(1, "bad wrpll refclk\n");
return 0;
}
r = wrpll & WRPLL_DIVIDER_REF_MASK;
p = (wrpll & WRPLL_DIVIDER_POST_MASK) >> WRPLL_DIVIDER_POST_SHIFT;
n = (wrpll & WRPLL_DIVIDER_FB_MASK) >> WRPLL_DIVIDER_FB_SHIFT;
/* Convert to KHz, p & r have a fixed point portion */
return (refclk * n * 100) / (p * r);
}
static int skl_calc_wrpll_link(struct drm_i915_private *dev_priv,
uint32_t dpll)
{
drm/i915: Type safe register read/write Make I915_READ and I915_WRITE more type safe by wrapping the register offset in a struct. This should eliminate most of the fumbles we've had with misplaced parens. This only takes care of normal mmio registers. We could extend the idea to other register types and define each with its own struct. That way you wouldn't be able to accidentally pass the wrong thing to a specific register access function. The gpio_reg setup is probably the ugliest thing left. But I figure I'd just leave it for now, and wait for some divine inspiration to strike before making it nice. As for the generated code, it's actually a bit better sometimes. Eg. looking at i915_irq_handler(), we can see the following change: lea 0x70024(%rdx,%rax,1),%r9d mov $0x1,%edx - movslq %r9d,%r9 - mov %r9,%rsi - mov %r9,-0x58(%rbp) - callq *0xd8(%rbx) + mov %r9d,%esi + mov %r9d,-0x48(%rbp) callq *0xd8(%rbx) So previously gcc thought the register offset might be signed and decided to sign extend it, just in case. The rest appears to be mostly just minor shuffling of instructions. v2: i915_mmio_reg_{offset,equal,valid}() helpers added s/_REG/_MMIO/ in the register defines mo more switch statements left to worry about ring_emit stuff got sorted in a prep patch cmd parser, lrc context and w/a batch buildup also in prep patch vgpu stuff cleaned up and moved to a prep patch all other unrelated changes split out v3: Rebased due to BXT DSI/BLC, MOCS, etc. v4: Rebased due to churn, s/i915_mmio_reg_t/i915_reg_t/ Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Link: http://patchwork.freedesktop.org/patch/msgid/1447853606-2751-1-git-send-email-ville.syrjala@linux.intel.com
2015-11-18 13:33:26 +00:00
i915_reg_t cfgcr1_reg, cfgcr2_reg;
uint32_t cfgcr1_val, cfgcr2_val;
uint32_t p0, p1, p2, dco_freq;
cfgcr1_reg = DPLL_CFGCR1(dpll);
cfgcr2_reg = DPLL_CFGCR2(dpll);
cfgcr1_val = I915_READ(cfgcr1_reg);
cfgcr2_val = I915_READ(cfgcr2_reg);
p0 = cfgcr2_val & DPLL_CFGCR2_PDIV_MASK;
p2 = cfgcr2_val & DPLL_CFGCR2_KDIV_MASK;
if (cfgcr2_val & DPLL_CFGCR2_QDIV_MODE(1))
p1 = (cfgcr2_val & DPLL_CFGCR2_QDIV_RATIO_MASK) >> 8;
else
p1 = 1;
switch (p0) {
case DPLL_CFGCR2_PDIV_1:
p0 = 1;
break;
case DPLL_CFGCR2_PDIV_2:
p0 = 2;
break;
case DPLL_CFGCR2_PDIV_3:
p0 = 3;
break;
case DPLL_CFGCR2_PDIV_7:
p0 = 7;
break;
}
switch (p2) {
case DPLL_CFGCR2_KDIV_5:
p2 = 5;
break;
case DPLL_CFGCR2_KDIV_2:
p2 = 2;
break;
case DPLL_CFGCR2_KDIV_3:
p2 = 3;
break;
case DPLL_CFGCR2_KDIV_1:
p2 = 1;
break;
}
dco_freq = (cfgcr1_val & DPLL_CFGCR1_DCO_INTEGER_MASK) * 24 * 1000;
dco_freq += (((cfgcr1_val & DPLL_CFGCR1_DCO_FRACTION_MASK) >> 9) * 24 *
1000) / 0x8000;
return dco_freq / (p0 * p1 * p2 * 5);
}
static int cnl_calc_wrpll_link(struct drm_i915_private *dev_priv,
uint32_t pll_id)
{
uint32_t cfgcr0, cfgcr1;
uint32_t p0, p1, p2, dco_freq, ref_clock;
cfgcr0 = I915_READ(CNL_DPLL_CFGCR0(pll_id));
cfgcr1 = I915_READ(CNL_DPLL_CFGCR1(pll_id));
p0 = cfgcr1 & DPLL_CFGCR1_PDIV_MASK;
p2 = cfgcr1 & DPLL_CFGCR1_KDIV_MASK;
if (cfgcr1 & DPLL_CFGCR1_QDIV_MODE(1))
p1 = (cfgcr1 & DPLL_CFGCR1_QDIV_RATIO_MASK) >>
DPLL_CFGCR1_QDIV_RATIO_SHIFT;
else
p1 = 1;
switch (p0) {
case DPLL_CFGCR1_PDIV_2:
p0 = 2;
break;
case DPLL_CFGCR1_PDIV_3:
p0 = 3;
break;
case DPLL_CFGCR1_PDIV_5:
p0 = 5;
break;
case DPLL_CFGCR1_PDIV_7:
p0 = 7;
break;
}
switch (p2) {
case DPLL_CFGCR1_KDIV_1:
p2 = 1;
break;
case DPLL_CFGCR1_KDIV_2:
p2 = 2;
break;
case DPLL_CFGCR1_KDIV_4:
p2 = 4;
break;
}
ref_clock = dev_priv->cdclk.hw.ref;
dco_freq = (cfgcr0 & DPLL_CFGCR0_DCO_INTEGER_MASK) * ref_clock;
dco_freq += (((cfgcr0 & DPLL_CFGCR0_DCO_FRACTION_MASK) >>
DPLL_CFGCR0_DCO_FRAC_SHIFT) * ref_clock) / 0x8000;
return dco_freq / (p0 * p1 * p2 * 5);
}
static void ddi_dotclock_get(struct intel_crtc_state *pipe_config)
{
int dotclock;
if (pipe_config->has_pch_encoder)
dotclock = intel_dotclock_calculate(pipe_config->port_clock,
&pipe_config->fdi_m_n);
else if (intel_crtc_has_dp_encoder(pipe_config))
dotclock = intel_dotclock_calculate(pipe_config->port_clock,
&pipe_config->dp_m_n);
else if (pipe_config->has_hdmi_sink && pipe_config->pipe_bpp == 36)
dotclock = pipe_config->port_clock * 2 / 3;
else
dotclock = pipe_config->port_clock;
drm/i915: prepare pipe for YCBCR420 output To get HDMI YCBCR420 output, the PIPEMISC register should be programmed to: - Generate YCBCR output (bit 11) - In case of YCBCR420 outputs, it should be programmed in full blend mode to use the scaler in 5x3 ratio (bits 26 and 27) This patch: - Adds definition of these bits. - Programs PIPEMISC for YCBCR420 outputs. - Adds readouts to compare HW and SW states. V2: rebase V3: rebase V4: rebase V5: added r-b from Ander V6: Handle only YCBCR420 outputs (ville) V7: rebase V8: Addressed review comments from Ville - Add readouts for state->ycbcr420 and 420 pixel_clock. - Handle warning due to mismatch in clock for ycbcr420 clock. - Rename PIPEMISC macros to match the Bspec. - Add a debug print stating if YCBCR 4:2:0 output enabled. Added r-b from Ville V9: Addressed review comments from Imre: - Add 420 mode clock adjustment in intel_hdmi_mode_valid to prevent 420_only modes getting rejected for high clock. - Add port clock adjustment for ycbcr420 modes in ddi_get_clock - Rename macros as per Ville's suggestion. - Remove unnecessary wl changes. V10: Added r-b from Imre V11: Fixed faulty dotclock handling, and addressed missing comment from previous set of review comments (Imre) V12: Fixed dotclock for 12bpc too, removed 420 check for GEN < 10 Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com> Cc: Daniel Vetter <daniel.vetter@intel.com> Cc: Imre Deak <imre.deak@intel.com> Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com> Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Shashank Sharma <shashank.sharma@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/1500904172-31717-1-git-send-email-shashank.sharma@intel.com Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2017-07-24 13:49:32 +00:00
if (pipe_config->ycbcr420)
dotclock *= 2;
if (pipe_config->pixel_multiplier)
dotclock /= pipe_config->pixel_multiplier;
pipe_config->base.adjusted_mode.crtc_clock = dotclock;
}
static void cnl_ddi_clock_get(struct intel_encoder *encoder,
struct intel_crtc_state *pipe_config)
{
struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
int link_clock = 0;
uint32_t cfgcr0, pll_id;
pll_id = intel_get_shared_dpll_id(dev_priv, pipe_config->shared_dpll);
cfgcr0 = I915_READ(CNL_DPLL_CFGCR0(pll_id));
if (cfgcr0 & DPLL_CFGCR0_HDMI_MODE) {
link_clock = cnl_calc_wrpll_link(dev_priv, pll_id);
} else {
link_clock = cfgcr0 & DPLL_CFGCR0_LINK_RATE_MASK;
switch (link_clock) {
case DPLL_CFGCR0_LINK_RATE_810:
link_clock = 81000;
break;
case DPLL_CFGCR0_LINK_RATE_1080:
link_clock = 108000;
break;
case DPLL_CFGCR0_LINK_RATE_1350:
link_clock = 135000;
break;
case DPLL_CFGCR0_LINK_RATE_1620:
link_clock = 162000;
break;
case DPLL_CFGCR0_LINK_RATE_2160:
link_clock = 216000;
break;
case DPLL_CFGCR0_LINK_RATE_2700:
link_clock = 270000;
break;
case DPLL_CFGCR0_LINK_RATE_3240:
link_clock = 324000;
break;
case DPLL_CFGCR0_LINK_RATE_4050:
link_clock = 405000;
break;
default:
WARN(1, "Unsupported link rate\n");
break;
}
link_clock *= 2;
}
pipe_config->port_clock = link_clock;
ddi_dotclock_get(pipe_config);
}
static void skl_ddi_clock_get(struct intel_encoder *encoder,
struct intel_crtc_state *pipe_config)
{
struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
int link_clock = 0;
uint32_t dpll_ctl1, dpll;
dpll = intel_get_shared_dpll_id(dev_priv, pipe_config->shared_dpll);
dpll_ctl1 = I915_READ(DPLL_CTRL1);
if (dpll_ctl1 & DPLL_CTRL1_HDMI_MODE(dpll)) {
link_clock = skl_calc_wrpll_link(dev_priv, dpll);
} else {
link_clock = dpll_ctl1 & DPLL_CTRL1_LINK_RATE_MASK(dpll);
link_clock >>= DPLL_CTRL1_LINK_RATE_SHIFT(dpll);
switch (link_clock) {
case DPLL_CTRL1_LINK_RATE_810:
link_clock = 81000;
break;
case DPLL_CTRL1_LINK_RATE_1080:
link_clock = 108000;
break;
case DPLL_CTRL1_LINK_RATE_1350:
link_clock = 135000;
break;
case DPLL_CTRL1_LINK_RATE_1620:
link_clock = 162000;
break;
case DPLL_CTRL1_LINK_RATE_2160:
link_clock = 216000;
break;
case DPLL_CTRL1_LINK_RATE_2700:
link_clock = 270000;
break;
default:
WARN(1, "Unsupported link rate\n");
break;
}
link_clock *= 2;
}
pipe_config->port_clock = link_clock;
ddi_dotclock_get(pipe_config);
}
static void hsw_ddi_clock_get(struct intel_encoder *encoder,
struct intel_crtc_state *pipe_config)
{
struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
int link_clock = 0;
u32 val, pll;
val = hsw_pll_to_ddi_pll_sel(pipe_config->shared_dpll);
switch (val & PORT_CLK_SEL_MASK) {
case PORT_CLK_SEL_LCPLL_810:
link_clock = 81000;
break;
case PORT_CLK_SEL_LCPLL_1350:
link_clock = 135000;
break;
case PORT_CLK_SEL_LCPLL_2700:
link_clock = 270000;
break;
case PORT_CLK_SEL_WRPLL1:
link_clock = hsw_ddi_calc_wrpll_link(dev_priv, WRPLL_CTL(0));
break;
case PORT_CLK_SEL_WRPLL2:
link_clock = hsw_ddi_calc_wrpll_link(dev_priv, WRPLL_CTL(1));
break;
case PORT_CLK_SEL_SPLL:
pll = I915_READ(SPLL_CTL) & SPLL_PLL_FREQ_MASK;
if (pll == SPLL_PLL_FREQ_810MHz)
link_clock = 81000;
else if (pll == SPLL_PLL_FREQ_1350MHz)
link_clock = 135000;
else if (pll == SPLL_PLL_FREQ_2700MHz)
link_clock = 270000;
else {
WARN(1, "bad spll freq\n");
return;
}
break;
default:
WARN(1, "bad port clock sel\n");
return;
}
pipe_config->port_clock = link_clock * 2;
ddi_dotclock_get(pipe_config);
}
static int bxt_calc_pll_link(struct drm_i915_private *dev_priv,
enum intel_dpll_id dpll)
{
struct intel_shared_dpll *pll;
struct intel_dpll_hw_state *state;
struct dpll clock;
/* For DDI ports we always use a shared PLL. */
if (WARN_ON(dpll == DPLL_ID_PRIVATE))
return 0;
pll = &dev_priv->shared_dplls[dpll];
state = &pll->state.hw_state;
clock.m1 = 2;
clock.m2 = (state->pll0 & PORT_PLL_M2_MASK) << 22;
if (state->pll3 & PORT_PLL_M2_FRAC_ENABLE)
clock.m2 |= state->pll2 & PORT_PLL_M2_FRAC_MASK;
clock.n = (state->pll1 & PORT_PLL_N_MASK) >> PORT_PLL_N_SHIFT;
clock.p1 = (state->ebb0 & PORT_PLL_P1_MASK) >> PORT_PLL_P1_SHIFT;
clock.p2 = (state->ebb0 & PORT_PLL_P2_MASK) >> PORT_PLL_P2_SHIFT;
return chv_calc_dpll_params(100000, &clock);
}
static void bxt_ddi_clock_get(struct intel_encoder *encoder,
struct intel_crtc_state *pipe_config)
{
struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
enum port port = intel_ddi_get_encoder_port(encoder);
uint32_t dpll = port;
pipe_config->port_clock = bxt_calc_pll_link(dev_priv, dpll);
ddi_dotclock_get(pipe_config);
}
void intel_ddi_clock_get(struct intel_encoder *encoder,
struct intel_crtc_state *pipe_config)
{
struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
if (INTEL_GEN(dev_priv) <= 8)
hsw_ddi_clock_get(encoder, pipe_config);
else if (IS_GEN9_BC(dev_priv))
skl_ddi_clock_get(encoder, pipe_config);
else if (IS_GEN9_LP(dev_priv))
bxt_ddi_clock_get(encoder, pipe_config);
else if (IS_CANNONLAKE(dev_priv))
cnl_ddi_clock_get(encoder, pipe_config);
}
void intel_ddi_set_pipe_settings(const struct intel_crtc_state *crtc_state)
{
struct intel_crtc *crtc = to_intel_crtc(crtc_state->base.crtc);
struct drm_i915_private *dev_priv = to_i915(crtc->base.dev);
struct intel_encoder *encoder = intel_ddi_get_crtc_encoder(crtc);
enum transcoder cpu_transcoder = crtc_state->cpu_transcoder;
int type = encoder->type;
uint32_t temp;
if (type == INTEL_OUTPUT_DP || type == INTEL_OUTPUT_EDP || type == INTEL_OUTPUT_DP_MST) {
WARN_ON(transcoder_is_dsi(cpu_transcoder));
temp = TRANS_MSA_SYNC_CLK;
switch (crtc_state->pipe_bpp) {
case 18:
temp |= TRANS_MSA_6_BPC;
break;
case 24:
temp |= TRANS_MSA_8_BPC;
break;
case 30:
temp |= TRANS_MSA_10_BPC;
break;
case 36:
temp |= TRANS_MSA_12_BPC;
break;
default:
drm/i915: precompute pipe bpp before touching the hw The procedure has now 3 steps: 1. Compute the bpp that the plane will output, this is done in pipe_config_set_bpp and stored into pipe_config->pipe_bpp. Also, this function clamps the pipe_bpp to whatever limit the EDID of any connected output specifies. 2. Adjust the pipe_bpp in the encoder and crtc functions, according to whatever constraints there are. 3. Decide whether to use dither by comparing the stored plane bpp with computed pipe_bpp. There are a few slight functional changes in this patch: - LVDS connector are now also going through the EDID clamping. But in a 2nd change we now unconditionally force the lvds bpc value - this shouldn't matter in reality when the panel setup is consistent, but better safe than sorry. - HDMI now forces the pipe_bpp to the selected value - I think that's what we actually want, since otherwise at least the pixelclock computations are wrong (I'm not sure whether the port would accept e.g. 10 bpc when in 12bpc mode). Contrary to the old code, we pick the next higher bpc value, since otherwise there's no way to make use of the 12 bpc mode (since the next patch will remove the 12bpc plane format, it doesn't exist). Both of these changes are due to the removal of the pipe_bpp = min(display_bpp, plane_bpp); statement. Another slight change is the reworking of the dp bpc code: - For the mode_valid callback it's sufficient to only check whether the mode would fit at the lowest bpc. - The bandwidth computation code is a bit restructured: It now walks all available bpp values in an outer loop and the codeblock that computes derived values (once a good configuration is found) has been moved out of the for loop maze. This is prep work to allow us to successively fall back on bpc values, and also correctly support bpc values != 8 or 6. v2: Rebased on top of Paulo Zanoni's little refactoring to use more drm dp helper functions. v3: Rebased on top of Jani's eDP bpp fix and Ville's limited color range work. v4: Remove the INTEL_MODE_DP_FORCE_6BPC #define, no longer needed. v5: Remove intel_crtc->bpp, too, and fix up the 12bpc check in the hdmi code. Also fixup the bpp check in intel_dp.c, it'll get reworked in a later patch though again. v6: Fix spelling in a comment. v7: Debug output improvements for the bpp computation. v8: Fixup 6bpc lvds check - dual-link and 8bpc mode are different things! v9: Reinstate the fix to properly ignore the firmware edp bpp ... this was lost in a rebase. v10: Both g4x and vlv lack 12bpc pipes, so don't enforce that we have that. Still unsure whether this is the way to go, but at least 6bpc for a 8bpc hdmi output seems to work. v11: And g4x/vlv also lack 12bpc hdmi support, so only support high depth on DP. Adjust the code. v12: Rebased. v13: Split out the introduction of pipe_config->dither|pipe_bpp, as requested from Jesse Barnes. v14: Split out the special 6BPC handling for DP, as requested by Jesse Barnes. Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2013-03-26 23:44:58 +00:00
BUG();
}
I915_WRITE(TRANS_MSA_MISC(cpu_transcoder), temp);
}
}
void intel_ddi_set_vc_payload_alloc(const struct intel_crtc_state *crtc_state,
bool state)
2014-05-02 04:02:48 +00:00
{
struct intel_crtc *crtc = to_intel_crtc(crtc_state->base.crtc);
struct drm_i915_private *dev_priv = to_i915(crtc->base.dev);
enum transcoder cpu_transcoder = crtc_state->cpu_transcoder;
2014-05-02 04:02:48 +00:00
uint32_t temp;
temp = I915_READ(TRANS_DDI_FUNC_CTL(cpu_transcoder));
if (state == true)
temp |= TRANS_DDI_DP_VC_PAYLOAD_ALLOC;
else
temp &= ~TRANS_DDI_DP_VC_PAYLOAD_ALLOC;
I915_WRITE(TRANS_DDI_FUNC_CTL(cpu_transcoder), temp);
}
void intel_ddi_enable_transcoder_func(const struct intel_crtc_state *crtc_state)
{
struct intel_crtc *crtc = to_intel_crtc(crtc_state->base.crtc);
struct intel_encoder *encoder = intel_ddi_get_crtc_encoder(crtc);
struct drm_i915_private *dev_priv = to_i915(crtc->base.dev);
enum pipe pipe = crtc->pipe;
enum transcoder cpu_transcoder = crtc_state->cpu_transcoder;
enum port port = intel_ddi_get_encoder_port(encoder);
int type = encoder->type;
uint32_t temp;
/* Enable TRANS_DDI_FUNC_CTL for the pipe to work in HDMI mode */
temp = TRANS_DDI_FUNC_ENABLE;
temp |= TRANS_DDI_SELECT_PORT(port);
switch (crtc_state->pipe_bpp) {
case 18:
temp |= TRANS_DDI_BPC_6;
break;
case 24:
temp |= TRANS_DDI_BPC_8;
break;
case 30:
temp |= TRANS_DDI_BPC_10;
break;
case 36:
temp |= TRANS_DDI_BPC_12;
break;
default:
drm/i915: precompute pipe bpp before touching the hw The procedure has now 3 steps: 1. Compute the bpp that the plane will output, this is done in pipe_config_set_bpp and stored into pipe_config->pipe_bpp. Also, this function clamps the pipe_bpp to whatever limit the EDID of any connected output specifies. 2. Adjust the pipe_bpp in the encoder and crtc functions, according to whatever constraints there are. 3. Decide whether to use dither by comparing the stored plane bpp with computed pipe_bpp. There are a few slight functional changes in this patch: - LVDS connector are now also going through the EDID clamping. But in a 2nd change we now unconditionally force the lvds bpc value - this shouldn't matter in reality when the panel setup is consistent, but better safe than sorry. - HDMI now forces the pipe_bpp to the selected value - I think that's what we actually want, since otherwise at least the pixelclock computations are wrong (I'm not sure whether the port would accept e.g. 10 bpc when in 12bpc mode). Contrary to the old code, we pick the next higher bpc value, since otherwise there's no way to make use of the 12 bpc mode (since the next patch will remove the 12bpc plane format, it doesn't exist). Both of these changes are due to the removal of the pipe_bpp = min(display_bpp, plane_bpp); statement. Another slight change is the reworking of the dp bpc code: - For the mode_valid callback it's sufficient to only check whether the mode would fit at the lowest bpc. - The bandwidth computation code is a bit restructured: It now walks all available bpp values in an outer loop and the codeblock that computes derived values (once a good configuration is found) has been moved out of the for loop maze. This is prep work to allow us to successively fall back on bpc values, and also correctly support bpc values != 8 or 6. v2: Rebased on top of Paulo Zanoni's little refactoring to use more drm dp helper functions. v3: Rebased on top of Jani's eDP bpp fix and Ville's limited color range work. v4: Remove the INTEL_MODE_DP_FORCE_6BPC #define, no longer needed. v5: Remove intel_crtc->bpp, too, and fix up the 12bpc check in the hdmi code. Also fixup the bpp check in intel_dp.c, it'll get reworked in a later patch though again. v6: Fix spelling in a comment. v7: Debug output improvements for the bpp computation. v8: Fixup 6bpc lvds check - dual-link and 8bpc mode are different things! v9: Reinstate the fix to properly ignore the firmware edp bpp ... this was lost in a rebase. v10: Both g4x and vlv lack 12bpc pipes, so don't enforce that we have that. Still unsure whether this is the way to go, but at least 6bpc for a 8bpc hdmi output seems to work. v11: And g4x/vlv also lack 12bpc hdmi support, so only support high depth on DP. Adjust the code. v12: Rebased. v13: Split out the introduction of pipe_config->dither|pipe_bpp, as requested from Jesse Barnes. v14: Split out the special 6BPC handling for DP, as requested by Jesse Barnes. Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2013-03-26 23:44:58 +00:00
BUG();
}
if (crtc_state->base.adjusted_mode.flags & DRM_MODE_FLAG_PVSYNC)
temp |= TRANS_DDI_PVSYNC;
if (crtc_state->base.adjusted_mode.flags & DRM_MODE_FLAG_PHSYNC)
temp |= TRANS_DDI_PHSYNC;
if (cpu_transcoder == TRANSCODER_EDP) {
switch (pipe) {
case PIPE_A:
/* On Haswell, can only use the always-on power well for
* eDP when not using the panel fitter, and when not
* using motion blur mitigation (which we don't
* support). */
if (IS_HASWELL(dev_priv) &&
(crtc_state->pch_pfit.enabled ||
crtc_state->pch_pfit.force_thru))
temp |= TRANS_DDI_EDP_INPUT_A_ONOFF;
else
temp |= TRANS_DDI_EDP_INPUT_A_ON;
break;
case PIPE_B:
temp |= TRANS_DDI_EDP_INPUT_B_ONOFF;
break;
case PIPE_C:
temp |= TRANS_DDI_EDP_INPUT_C_ONOFF;
break;
default:
BUG();
break;
}
}
if (type == INTEL_OUTPUT_HDMI) {
if (crtc_state->has_hdmi_sink)
temp |= TRANS_DDI_MODE_SELECT_HDMI;
else
temp |= TRANS_DDI_MODE_SELECT_DVI;
drm/i915: enable scrambling Geminilake platform sports a native HDMI 2.0 controller, and is capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec mendates scrambling for these higher clocks, for reduced RF footprint. This patch checks if the monitor supports scrambling, and if required, enables it during the modeset. V2: Addressed review comments from Ville: - Do not track scrambling status in DRM layer, track somewhere in driver like in intel_crtc_state. - Don't talk to monitor at such a low layer, set monitor scrambling in intel_enable_ddi() before enabling the port. V3: Addressed review comments from Jani - In comments, function names, use "sink" instead of "monitor", so that the implementation could be close to the language of HDMI spec. V4: Addressed review comment from Maarten - scrambling -> hdmi_scrambling - high_tmds_clock_ratio -> hdmi_high_tmds_clock_ratio V5: Addressed review comments from Ville and Ander - Do not modifiy the crtc_state after compute_config. Move all scrambling and tmds_clock_ratio calcutations to compute_config. - While setting scrambling for source/sink, do not check the conditions again, just go by the crtc_state flags. This will simplyfy the condition checks. V6: Addressed review comments from Ville - Do not add IS_GLK check in disable/enable function, instead add it in compute_config, while setting state flags. - Remove unnecessary paranthesis. - Simplyfy handle_sink_scrambling function as suggested. - Add readout code for scrambling status in get_ddi_config and add a check for the same in pipe_config_compare. V7: Addressed review comments from Ander/Ville - No separate function for source scrambling, make it inline - Align the last line of the macro TRANS_DDI_HDMI_SCRAMBLING_MASK - Do not add platform check while setting source scrambling - Use pipe_config instead of crtc->config to set sink scrambling - To readout scrambling status, Compare with SCRAMBLING_MASK not any of its bits - Remove platform check in intel_pipe_config_compare while checking scrambling status V8: Fixed mege conflict, Addressed review comments from Ander - Remove the desciption/comment about scrambling fom the caller, move it to the function - Move the IS_GLK check into scrambling function - Fix alignment V9: Fixed review comments from Ville, Ander - Pass the scrambling state variables as bool input to the sink_scrambling function and let the disable call be unconditional. - Fix alignments in function calls and debug messages. - Add kernel doc for function intel_hdmi_handle_sink_scrambling V10: Rebase Signed-off-by: Shashank Sharma <shashank.sharma@intel.com> Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1489404244-16608-6-git-send-email-shashank.sharma@intel.com
2017-03-13 11:24:03 +00:00
if (crtc_state->hdmi_scrambling)
temp |= TRANS_DDI_HDMI_SCRAMBLING_MASK;
if (crtc_state->hdmi_high_tmds_clock_ratio)
temp |= TRANS_DDI_HIGH_TMDS_CHAR_RATE;
} else if (type == INTEL_OUTPUT_ANALOG) {
temp |= TRANS_DDI_MODE_SELECT_FDI;
temp |= (crtc_state->fdi_lanes - 1) << 1;
} else if (type == INTEL_OUTPUT_DP ||
type == INTEL_OUTPUT_EDP) {
temp |= TRANS_DDI_MODE_SELECT_DP_SST;
temp |= DDI_PORT_WIDTH(crtc_state->lane_count);
2014-05-02 04:02:48 +00:00
} else if (type == INTEL_OUTPUT_DP_MST) {
temp |= TRANS_DDI_MODE_SELECT_DP_MST;
temp |= DDI_PORT_WIDTH(crtc_state->lane_count);
} else {
WARN(1, "Invalid encoder type %d for pipe %c\n",
encoder->type, pipe_name(pipe));
}
I915_WRITE(TRANS_DDI_FUNC_CTL(cpu_transcoder), temp);
}
void intel_ddi_disable_transcoder_func(struct drm_i915_private *dev_priv,
enum transcoder cpu_transcoder)
{
drm/i915: Type safe register read/write Make I915_READ and I915_WRITE more type safe by wrapping the register offset in a struct. This should eliminate most of the fumbles we've had with misplaced parens. This only takes care of normal mmio registers. We could extend the idea to other register types and define each with its own struct. That way you wouldn't be able to accidentally pass the wrong thing to a specific register access function. The gpio_reg setup is probably the ugliest thing left. But I figure I'd just leave it for now, and wait for some divine inspiration to strike before making it nice. As for the generated code, it's actually a bit better sometimes. Eg. looking at i915_irq_handler(), we can see the following change: lea 0x70024(%rdx,%rax,1),%r9d mov $0x1,%edx - movslq %r9d,%r9 - mov %r9,%rsi - mov %r9,-0x58(%rbp) - callq *0xd8(%rbx) + mov %r9d,%esi + mov %r9d,-0x48(%rbp) callq *0xd8(%rbx) So previously gcc thought the register offset might be signed and decided to sign extend it, just in case. The rest appears to be mostly just minor shuffling of instructions. v2: i915_mmio_reg_{offset,equal,valid}() helpers added s/_REG/_MMIO/ in the register defines mo more switch statements left to worry about ring_emit stuff got sorted in a prep patch cmd parser, lrc context and w/a batch buildup also in prep patch vgpu stuff cleaned up and moved to a prep patch all other unrelated changes split out v3: Rebased due to BXT DSI/BLC, MOCS, etc. v4: Rebased due to churn, s/i915_mmio_reg_t/i915_reg_t/ Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Link: http://patchwork.freedesktop.org/patch/msgid/1447853606-2751-1-git-send-email-ville.syrjala@linux.intel.com
2015-11-18 13:33:26 +00:00
i915_reg_t reg = TRANS_DDI_FUNC_CTL(cpu_transcoder);
uint32_t val = I915_READ(reg);
2014-05-02 04:02:48 +00:00
val &= ~(TRANS_DDI_FUNC_ENABLE | TRANS_DDI_PORT_MASK | TRANS_DDI_DP_VC_PAYLOAD_ALLOC);
val |= TRANS_DDI_PORT_NONE;
I915_WRITE(reg, val);
}
bool intel_ddi_connector_get_hw_state(struct intel_connector *intel_connector)
{
struct drm_device *dev = intel_connector->base.dev;
struct drm_i915_private *dev_priv = to_i915(dev);
struct intel_encoder *encoder = intel_connector->encoder;
int type = intel_connector->base.connector_type;
enum port port = intel_ddi_get_encoder_port(encoder);
enum pipe pipe = 0;
enum transcoder cpu_transcoder;
uint32_t tmp;
bool ret;
if (!intel_display_power_get_if_enabled(dev_priv,
encoder->power_domain))
return false;
if (!encoder->get_hw_state(encoder, &pipe)) {
ret = false;
goto out;
}
if (port == PORT_A)
cpu_transcoder = TRANSCODER_EDP;
else
cpu_transcoder = (enum transcoder) pipe;
tmp = I915_READ(TRANS_DDI_FUNC_CTL(cpu_transcoder));
switch (tmp & TRANS_DDI_MODE_SELECT_MASK) {
case TRANS_DDI_MODE_SELECT_HDMI:
case TRANS_DDI_MODE_SELECT_DVI:
ret = type == DRM_MODE_CONNECTOR_HDMIA;
break;
case TRANS_DDI_MODE_SELECT_DP_SST:
ret = type == DRM_MODE_CONNECTOR_eDP ||
type == DRM_MODE_CONNECTOR_DisplayPort;
break;
2014-05-02 04:02:48 +00:00
case TRANS_DDI_MODE_SELECT_DP_MST:
/* if the transcoder is in MST state then
* connector isn't connected */
ret = false;
break;
case TRANS_DDI_MODE_SELECT_FDI:
ret = type == DRM_MODE_CONNECTOR_VGA;
break;
default:
ret = false;
break;
}
out:
intel_display_power_put(dev_priv, encoder->power_domain);
return ret;
}
bool intel_ddi_get_hw_state(struct intel_encoder *encoder,
enum pipe *pipe)
{
struct drm_device *dev = encoder->base.dev;
struct drm_i915_private *dev_priv = to_i915(dev);
enum port port = intel_ddi_get_encoder_port(encoder);
u32 tmp;
int i;
bool ret;
if (!intel_display_power_get_if_enabled(dev_priv,
encoder->power_domain))
return false;
ret = false;
tmp = I915_READ(DDI_BUF_CTL(port));
if (!(tmp & DDI_BUF_CTL_ENABLE))
goto out;
if (port == PORT_A) {
tmp = I915_READ(TRANS_DDI_FUNC_CTL(TRANSCODER_EDP));
switch (tmp & TRANS_DDI_EDP_INPUT_MASK) {
case TRANS_DDI_EDP_INPUT_A_ON:
case TRANS_DDI_EDP_INPUT_A_ONOFF:
*pipe = PIPE_A;
break;
case TRANS_DDI_EDP_INPUT_B_ONOFF:
*pipe = PIPE_B;
break;
case TRANS_DDI_EDP_INPUT_C_ONOFF:
*pipe = PIPE_C;
break;
}
ret = true;
goto out;
}
2014-05-02 04:02:48 +00:00
for (i = TRANSCODER_A; i <= TRANSCODER_C; i++) {
tmp = I915_READ(TRANS_DDI_FUNC_CTL(i));
if ((tmp & TRANS_DDI_PORT_MASK) == TRANS_DDI_SELECT_PORT(port)) {
if ((tmp & TRANS_DDI_MODE_SELECT_MASK) ==
TRANS_DDI_MODE_SELECT_DP_MST)
goto out;
*pipe = i;
ret = true;
goto out;
}
}
DRM_DEBUG_KMS("No pipe for ddi port %c found\n", port_name(port));
out:
if (ret && IS_GEN9_LP(dev_priv)) {
tmp = I915_READ(BXT_PHY_CTL(port));
if ((tmp & (BXT_PHY_LANE_POWERDOWN_ACK |
BXT_PHY_LANE_ENABLED)) != BXT_PHY_LANE_ENABLED)
DRM_ERROR("Port %c enabled but PHY powered down? "
"(PHY_CTL %08x)\n", port_name(port), tmp);
}
intel_display_power_put(dev_priv, encoder->power_domain);
return ret;
}
static u64 intel_ddi_get_power_domains(struct intel_encoder *encoder)
{
struct intel_digital_port *dig_port = enc_to_dig_port(&encoder->base);
enum pipe pipe;
if (intel_ddi_get_hw_state(encoder, &pipe))
return BIT_ULL(dig_port->ddi_io_power_domain);
return 0;
}
void intel_ddi_enable_pipe_clock(const struct intel_crtc_state *crtc_state)
{
struct intel_crtc *crtc = to_intel_crtc(crtc_state->base.crtc);
struct drm_i915_private *dev_priv = to_i915(crtc->base.dev);
struct intel_encoder *encoder = intel_ddi_get_crtc_encoder(crtc);
enum port port = intel_ddi_get_encoder_port(encoder);
enum transcoder cpu_transcoder = crtc_state->cpu_transcoder;
if (cpu_transcoder != TRANSCODER_EDP)
I915_WRITE(TRANS_CLK_SEL(cpu_transcoder),
TRANS_CLK_SEL_PORT(port));
}
void intel_ddi_disable_pipe_clock(const struct intel_crtc_state *crtc_state)
{
struct drm_i915_private *dev_priv = to_i915(crtc_state->base.crtc->dev);
enum transcoder cpu_transcoder = crtc_state->cpu_transcoder;
if (cpu_transcoder != TRANSCODER_EDP)
I915_WRITE(TRANS_CLK_SEL(cpu_transcoder),
TRANS_CLK_SEL_DISABLED);
}
static void _skl_ddi_set_iboost(struct drm_i915_private *dev_priv,
enum port port, uint8_t iboost)
{
u32 tmp;
tmp = I915_READ(DISPIO_CR_TX_BMU_CR0);
tmp &= ~(BALANCE_LEG_MASK(port) | BALANCE_LEG_DISABLE(port));
if (iboost)
tmp |= iboost << BALANCE_LEG_SHIFT(port);
else
tmp |= BALANCE_LEG_DISABLE(port);
I915_WRITE(DISPIO_CR_TX_BMU_CR0, tmp);
}
static void skl_ddi_set_iboost(struct intel_encoder *encoder, u32 level)
{
struct intel_digital_port *intel_dig_port = enc_to_dig_port(&encoder->base);
struct drm_i915_private *dev_priv = to_i915(intel_dig_port->base.base.dev);
enum port port = intel_dig_port->port;
int type = encoder->type;
const struct ddi_buf_trans *ddi_translations;
uint8_t iboost;
uint8_t dp_iboost, hdmi_iboost;
int n_entries;
/* VBT may override standard boost values */
dp_iboost = dev_priv->vbt.ddi_port_info[port].dp_boost_level;
hdmi_iboost = dev_priv->vbt.ddi_port_info[port].hdmi_boost_level;
if (type == INTEL_OUTPUT_DP) {
if (dp_iboost) {
iboost = dp_iboost;
} else {
if (IS_KABYLAKE(dev_priv) || IS_COFFEELAKE(dev_priv))
ddi_translations = kbl_get_buf_trans_dp(dev_priv,
&n_entries);
else
ddi_translations = skl_get_buf_trans_dp(dev_priv,
&n_entries);
iboost = ddi_translations[level].i_boost;
}
} else if (type == INTEL_OUTPUT_EDP) {
if (dp_iboost) {
iboost = dp_iboost;
} else {
ddi_translations = skl_get_buf_trans_edp(dev_priv, &n_entries);
if (WARN_ON(port != PORT_A &&
port != PORT_E && n_entries > 9))
n_entries = 9;
iboost = ddi_translations[level].i_boost;
}
} else if (type == INTEL_OUTPUT_HDMI) {
if (hdmi_iboost) {
iboost = hdmi_iboost;
} else {
ddi_translations = skl_get_buf_trans_hdmi(dev_priv, &n_entries);
iboost = ddi_translations[level].i_boost;
}
} else {
return;
}
/* Make sure that the requested I_boost is valid */
if (iboost && iboost != 0x1 && iboost != 0x3 && iboost != 0x7) {
DRM_ERROR("Invalid I_boost value %u\n", iboost);
return;
}
_skl_ddi_set_iboost(dev_priv, port, iboost);
if (port == PORT_A && intel_dig_port->max_lanes == 4)
_skl_ddi_set_iboost(dev_priv, PORT_E, iboost);
}
static void bxt_ddi_vswing_sequence(struct drm_i915_private *dev_priv,
u32 level, enum port port, int type)
drm/i915/bxt: VSwing programming sequence VSwing programming sequence as specified in the updated BXT BSpec v2: Satheesh's review comments addressed. - clear value before setting into registers - move print statement to bxt function Other changes - since signal level will not be set into DDI_BUF_CTL, the value need not be returned to intel_dp_set_signal_levels(). Making the bxt specific function to return void and setting signal_levels = 0 for bxt inside intel_dp_set_signal_levels() - instead of signal levels, printing vswing level and pre-emphasis level - in case none of the pre-emphasis levels or vswing levels are set, setting default of 400mV + 0dB v3: Satheesh's review comments - Check for mask before printing signal_levels. - Removing redundant register writes - Call intel_prepare_ddi_buffers only for HAS_PCH_SPLIT - Making register write part generic as it will be required for HDMI as well. Re-structure the code to include an array for vswing related values, set signal levels v4: Satheesh's review comments - Rebase over latest renaming patches - use hsw_signal_levels for HAS_DDI Other changes - Modified vswing_sequence() func definition - Rebased on top of register macro definitions v5: Satheesh's review comments - Check ddi translation table size v6: Imre's review comments - removed comments in vswing sequence - added vswing, pre-emphasis prints in intel_dp_set_signal_levels - added comment explaining use of DP vswing values for eDP - initialize n_entries and ddi_transaltion table based on encoder type - create bxt_ddi_buf_trans structure and use decimal values - adding a flag in bxt buffer translation table to indicate def entry v7: (imre) - squash in Vandana's "VSwing register definition", "HDMI VSwing programming", "Re-enable vswing programming", "Fix vswing sequence" patches - use BXT_PORT_* regs directly instead of via a temp var - simplify BXT_PORT_* macro definitions - add code comment why we read lane while write group registers - fix readout of DP_TRAIN_PRE_EMPHASIS in debug message Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> (v6) Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2014-11-18 10:15:27 +00:00
{
const struct bxt_ddi_buf_trans *ddi_translations;
u32 n_entries, i;
if (type == INTEL_OUTPUT_EDP && dev_priv->vbt.edp.low_vswing) {
n_entries = ARRAY_SIZE(bxt_ddi_translations_edp);
ddi_translations = bxt_ddi_translations_edp;
} else if (type == INTEL_OUTPUT_DP
|| type == INTEL_OUTPUT_EDP) {
drm/i915/bxt: VSwing programming sequence VSwing programming sequence as specified in the updated BXT BSpec v2: Satheesh's review comments addressed. - clear value before setting into registers - move print statement to bxt function Other changes - since signal level will not be set into DDI_BUF_CTL, the value need not be returned to intel_dp_set_signal_levels(). Making the bxt specific function to return void and setting signal_levels = 0 for bxt inside intel_dp_set_signal_levels() - instead of signal levels, printing vswing level and pre-emphasis level - in case none of the pre-emphasis levels or vswing levels are set, setting default of 400mV + 0dB v3: Satheesh's review comments - Check for mask before printing signal_levels. - Removing redundant register writes - Call intel_prepare_ddi_buffers only for HAS_PCH_SPLIT - Making register write part generic as it will be required for HDMI as well. Re-structure the code to include an array for vswing related values, set signal levels v4: Satheesh's review comments - Rebase over latest renaming patches - use hsw_signal_levels for HAS_DDI Other changes - Modified vswing_sequence() func definition - Rebased on top of register macro definitions v5: Satheesh's review comments - Check ddi translation table size v6: Imre's review comments - removed comments in vswing sequence - added vswing, pre-emphasis prints in intel_dp_set_signal_levels - added comment explaining use of DP vswing values for eDP - initialize n_entries and ddi_transaltion table based on encoder type - create bxt_ddi_buf_trans structure and use decimal values - adding a flag in bxt buffer translation table to indicate def entry v7: (imre) - squash in Vandana's "VSwing register definition", "HDMI VSwing programming", "Re-enable vswing programming", "Fix vswing sequence" patches - use BXT_PORT_* regs directly instead of via a temp var - simplify BXT_PORT_* macro definitions - add code comment why we read lane while write group registers - fix readout of DP_TRAIN_PRE_EMPHASIS in debug message Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> (v6) Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2014-11-18 10:15:27 +00:00
n_entries = ARRAY_SIZE(bxt_ddi_translations_dp);
ddi_translations = bxt_ddi_translations_dp;
} else if (type == INTEL_OUTPUT_HDMI) {
n_entries = ARRAY_SIZE(bxt_ddi_translations_hdmi);
ddi_translations = bxt_ddi_translations_hdmi;
} else {
DRM_DEBUG_KMS("Vswing programming not done for encoder %d\n",
type);
return;
}
/* Check if default value has to be used */
if (level >= n_entries ||
(type == INTEL_OUTPUT_HDMI && level == HDMI_LEVEL_SHIFT_UNKNOWN)) {
for (i = 0; i < n_entries; i++) {
if (ddi_translations[i].default_index) {
level = i;
break;
}
}
}
bxt_ddi_phy_set_signal_level(dev_priv, port,
ddi_translations[level].margin,
ddi_translations[level].scale,
ddi_translations[level].enable,
ddi_translations[level].deemphasis);
drm/i915/bxt: VSwing programming sequence VSwing programming sequence as specified in the updated BXT BSpec v2: Satheesh's review comments addressed. - clear value before setting into registers - move print statement to bxt function Other changes - since signal level will not be set into DDI_BUF_CTL, the value need not be returned to intel_dp_set_signal_levels(). Making the bxt specific function to return void and setting signal_levels = 0 for bxt inside intel_dp_set_signal_levels() - instead of signal levels, printing vswing level and pre-emphasis level - in case none of the pre-emphasis levels or vswing levels are set, setting default of 400mV + 0dB v3: Satheesh's review comments - Check for mask before printing signal_levels. - Removing redundant register writes - Call intel_prepare_ddi_buffers only for HAS_PCH_SPLIT - Making register write part generic as it will be required for HDMI as well. Re-structure the code to include an array for vswing related values, set signal levels v4: Satheesh's review comments - Rebase over latest renaming patches - use hsw_signal_levels for HAS_DDI Other changes - Modified vswing_sequence() func definition - Rebased on top of register macro definitions v5: Satheesh's review comments - Check ddi translation table size v6: Imre's review comments - removed comments in vswing sequence - added vswing, pre-emphasis prints in intel_dp_set_signal_levels - added comment explaining use of DP vswing values for eDP - initialize n_entries and ddi_transaltion table based on encoder type - create bxt_ddi_buf_trans structure and use decimal values - adding a flag in bxt buffer translation table to indicate def entry v7: (imre) - squash in Vandana's "VSwing register definition", "HDMI VSwing programming", "Re-enable vswing programming", "Fix vswing sequence" patches - use BXT_PORT_* regs directly instead of via a temp var - simplify BXT_PORT_* macro definitions - add code comment why we read lane while write group registers - fix readout of DP_TRAIN_PRE_EMPHASIS in debug message Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> (v6) Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2014-11-18 10:15:27 +00:00
}
u8 intel_ddi_dp_voltage_max(struct intel_encoder *encoder)
{
struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
int n_entries;
if (encoder->type == INTEL_OUTPUT_EDP)
intel_ddi_get_buf_trans_edp(dev_priv, &n_entries);
else
intel_ddi_get_buf_trans_dp(dev_priv, &n_entries);
if (WARN_ON(n_entries < 1))
n_entries = 1;
if (WARN_ON(n_entries > ARRAY_SIZE(index_to_dp_signal_levels)))
n_entries = ARRAY_SIZE(index_to_dp_signal_levels);
return index_to_dp_signal_levels[n_entries - 1] &
DP_TRAIN_VOLTAGE_SWING_MASK;
}
static const struct cnl_ddi_buf_trans *
cnl_get_buf_trans_hdmi(struct drm_i915_private *dev_priv,
u32 voltage, int *n_entries)
{
if (voltage == VOLTAGE_INFO_0_85V) {
*n_entries = ARRAY_SIZE(cnl_ddi_translations_hdmi_0_85V);
return cnl_ddi_translations_hdmi_0_85V;
} else if (voltage == VOLTAGE_INFO_0_95V) {
*n_entries = ARRAY_SIZE(cnl_ddi_translations_hdmi_0_95V);
return cnl_ddi_translations_hdmi_0_95V;
} else if (voltage == VOLTAGE_INFO_1_05V) {
*n_entries = ARRAY_SIZE(cnl_ddi_translations_hdmi_1_05V);
return cnl_ddi_translations_hdmi_1_05V;
}
return NULL;
}
static const struct cnl_ddi_buf_trans *
cnl_get_buf_trans_dp(struct drm_i915_private *dev_priv,
u32 voltage, int *n_entries)
{
if (voltage == VOLTAGE_INFO_0_85V) {
*n_entries = ARRAY_SIZE(cnl_ddi_translations_dp_0_85V);
return cnl_ddi_translations_dp_0_85V;
} else if (voltage == VOLTAGE_INFO_0_95V) {
*n_entries = ARRAY_SIZE(cnl_ddi_translations_dp_0_95V);
return cnl_ddi_translations_dp_0_95V;
} else if (voltage == VOLTAGE_INFO_1_05V) {
*n_entries = ARRAY_SIZE(cnl_ddi_translations_dp_1_05V);
return cnl_ddi_translations_dp_1_05V;
}
return NULL;
}
static const struct cnl_ddi_buf_trans *
cnl_get_buf_trans_edp(struct drm_i915_private *dev_priv,
u32 voltage, int *n_entries)
{
if (dev_priv->vbt.edp.low_vswing) {
if (voltage == VOLTAGE_INFO_0_85V) {
*n_entries = ARRAY_SIZE(cnl_ddi_translations_edp_0_85V);
return cnl_ddi_translations_edp_0_85V;
} else if (voltage == VOLTAGE_INFO_0_95V) {
*n_entries = ARRAY_SIZE(cnl_ddi_translations_edp_0_95V);
return cnl_ddi_translations_edp_0_95V;
} else if (voltage == VOLTAGE_INFO_1_05V) {
*n_entries = ARRAY_SIZE(cnl_ddi_translations_edp_1_05V);
return cnl_ddi_translations_edp_1_05V;
}
return NULL;
} else {
return cnl_get_buf_trans_dp(dev_priv, voltage, n_entries);
}
}
static void cnl_ddi_vswing_program(struct drm_i915_private *dev_priv,
u32 level, enum port port, int type)
{
const struct cnl_ddi_buf_trans *ddi_translations = NULL;
u32 n_entries, val, voltage;
int ln;
/*
* Values for each port type are listed in
* voltage swing programming tables.
* Vccio voltage found in PORT_COMP_DW3.
*/
voltage = I915_READ(CNL_PORT_COMP_DW3) & VOLTAGE_INFO_MASK;
if (type == INTEL_OUTPUT_HDMI) {
ddi_translations = cnl_get_buf_trans_hdmi(dev_priv,
voltage, &n_entries);
} else if (type == INTEL_OUTPUT_DP) {
ddi_translations = cnl_get_buf_trans_dp(dev_priv,
voltage, &n_entries);
} else if (type == INTEL_OUTPUT_EDP) {
ddi_translations = cnl_get_buf_trans_edp(dev_priv,
voltage, &n_entries);
}
if (ddi_translations == NULL) {
MISSING_CASE(voltage);
return;
}
if (level >= n_entries) {
DRM_DEBUG_KMS("DDI translation not found for level %d. Using %d instead.", level, n_entries - 1);
level = n_entries - 1;
}
/* Set PORT_TX_DW5 Scaling Mode Sel to 010b. */
val = I915_READ(CNL_PORT_TX_DW5_LN0(port));
val &= ~SCALING_MODE_SEL_MASK;
val |= SCALING_MODE_SEL(2);
I915_WRITE(CNL_PORT_TX_DW5_GRP(port), val);
/* Program PORT_TX_DW2 */
val = I915_READ(CNL_PORT_TX_DW2_LN0(port));
val &= ~(SWING_SEL_LOWER_MASK | SWING_SEL_UPPER_MASK |
RCOMP_SCALAR_MASK);
val |= SWING_SEL_UPPER(ddi_translations[level].dw2_swing_sel);
val |= SWING_SEL_LOWER(ddi_translations[level].dw2_swing_sel);
/* Rcomp scalar is fixed as 0x98 for every table entry */
val |= RCOMP_SCALAR(0x98);
I915_WRITE(CNL_PORT_TX_DW2_GRP(port), val);
/* Program PORT_TX_DW4 */
/* We cannot write to GRP. It would overrite individual loadgen */
for (ln = 0; ln < 4; ln++) {
val = I915_READ(CNL_PORT_TX_DW4_LN(port, ln));
val &= ~(POST_CURSOR_1_MASK | POST_CURSOR_2_MASK |
CURSOR_COEFF_MASK);
val |= POST_CURSOR_1(ddi_translations[level].dw4_post_cursor_1);
val |= POST_CURSOR_2(ddi_translations[level].dw4_post_cursor_2);
val |= CURSOR_COEFF(ddi_translations[level].dw4_cursor_coeff);
I915_WRITE(CNL_PORT_TX_DW4_LN(port, ln), val);
}
/* Program PORT_TX_DW5 */
/* All DW5 values are fixed for every table entry */
val = I915_READ(CNL_PORT_TX_DW5_LN0(port));
val &= ~RTERM_SELECT_MASK;
val |= RTERM_SELECT(6);
val |= TAP3_DISABLE;
I915_WRITE(CNL_PORT_TX_DW5_GRP(port), val);
/* Program PORT_TX_DW7 */
val = I915_READ(CNL_PORT_TX_DW7_LN0(port));
val &= ~N_SCALAR_MASK;
val |= N_SCALAR(ddi_translations[level].dw7_n_scalar);
I915_WRITE(CNL_PORT_TX_DW7_GRP(port), val);
}
static void cnl_ddi_vswing_sequence(struct intel_encoder *encoder, u32 level)
{
struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
struct intel_dp *intel_dp = enc_to_intel_dp(&encoder->base);
enum port port = intel_ddi_get_encoder_port(encoder);
int type = encoder->type;
int width = 0;
int rate = 0;
u32 val;
int ln = 0;
if ((intel_dp) && (type == INTEL_OUTPUT_EDP || type == INTEL_OUTPUT_DP)) {
width = intel_dp->lane_count;
rate = intel_dp->link_rate;
} else if (type == INTEL_OUTPUT_HDMI) {
width = 4;
/* Rate is always < than 6GHz for HDMI */
} else {
MISSING_CASE(type);
return;
}
/*
* 1. If port type is eDP or DP,
* set PORT_PCS_DW1 cmnkeeper_enable to 1b,
* else clear to 0b.
*/
val = I915_READ(CNL_PORT_PCS_DW1_LN0(port));
if (type == INTEL_OUTPUT_EDP || type == INTEL_OUTPUT_DP)
val |= COMMON_KEEPER_EN;
else
val &= ~COMMON_KEEPER_EN;
I915_WRITE(CNL_PORT_PCS_DW1_GRP(port), val);
/* 2. Program loadgen select */
/*
* Program PORT_TX_DW4_LN depending on Bit rate and used lanes
* <= 6 GHz and 4 lanes (LN0=0, LN1=1, LN2=1, LN3=1)
* <= 6 GHz and 1,2 lanes (LN0=0, LN1=1, LN2=1, LN3=0)
* > 6 GHz (LN0=0, LN1=0, LN2=0, LN3=0)
*/
for (ln = 0; ln <= 3; ln++) {
val = I915_READ(CNL_PORT_TX_DW4_LN(port, ln));
val &= ~LOADGEN_SELECT;
if ((rate <= 600000 && width == 4 && ln >= 1) ||
(rate <= 600000 && width < 4 && (ln == 1 || ln == 2))) {
val |= LOADGEN_SELECT;
}
I915_WRITE(CNL_PORT_TX_DW4_LN(port, ln), val);
}
/* 3. Set PORT_CL_DW5 SUS Clock Config to 11b */
val = I915_READ(CNL_PORT_CL1CM_DW5);
val |= SUS_CLOCK_CONFIG;
I915_WRITE(CNL_PORT_CL1CM_DW5, val);
/* 4. Clear training enable to change swing values */
val = I915_READ(CNL_PORT_TX_DW5_LN0(port));
val &= ~TX_TRAINING_EN;
I915_WRITE(CNL_PORT_TX_DW5_GRP(port), val);
/* 5. Program swing and de-emphasis */
cnl_ddi_vswing_program(dev_priv, level, port, type);
/* 6. Set training enable to trigger update */
val = I915_READ(CNL_PORT_TX_DW5_LN0(port));
val |= TX_TRAINING_EN;
I915_WRITE(CNL_PORT_TX_DW5_GRP(port), val);
}
static uint32_t translate_signal_level(int signal_levels)
{
int i;
for (i = 0; i < ARRAY_SIZE(index_to_dp_signal_levels); i++) {
if (index_to_dp_signal_levels[i] == signal_levels)
return i;
}
WARN(1, "Unsupported voltage swing/pre-emphasis level: 0x%x\n",
signal_levels);
return 0;
}
uint32_t ddi_signal_levels(struct intel_dp *intel_dp)
{
struct intel_digital_port *dport = dp_to_dig_port(intel_dp);
struct drm_i915_private *dev_priv = to_i915(dport->base.base.dev);
struct intel_encoder *encoder = &dport->base;
uint8_t train_set = intel_dp->train_set[0];
int signal_levels = train_set & (DP_TRAIN_VOLTAGE_SWING_MASK |
DP_TRAIN_PRE_EMPHASIS_MASK);
enum port port = dport->port;
uint32_t level;
level = translate_signal_level(signal_levels);
if (IS_GEN9_BC(dev_priv))
skl_ddi_set_iboost(encoder, level);
else if (IS_GEN9_LP(dev_priv))
bxt_ddi_vswing_sequence(dev_priv, level, port, encoder->type);
else if (IS_CANNONLAKE(dev_priv)) {
cnl_ddi_vswing_sequence(encoder, level);
/* DDI_BUF_CTL bits 27:24 are reserved on CNL */
return 0;
}
return DDI_BUF_TRANS_SELECT(level);
}
static void intel_ddi_clk_select(struct intel_encoder *encoder,
struct intel_shared_dpll *pll)
{
struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
enum port port = intel_ddi_get_encoder_port(encoder);
uint32_t val;
if (WARN_ON(!pll))
return;
if (IS_CANNONLAKE(dev_priv)) {
/* Configure DPCLKA_CFGCR0 to map the DPLL to the DDI. */
val = I915_READ(DPCLKA_CFGCR0);
val |= DPCLKA_CFGCR0_DDI_CLK_SEL(pll->id, port);
I915_WRITE(DPCLKA_CFGCR0, val);
/*
* Configure DPCLKA_CFGCR0 to turn on the clock for the DDI.
* This step and the step before must be done with separate
* register writes.
*/
val = I915_READ(DPCLKA_CFGCR0);
val &= ~(DPCLKA_CFGCR0_DDI_CLK_OFF(port) |
DPCLKA_CFGCR0_DDI_CLK_SEL_MASK(port));
I915_WRITE(DPCLKA_CFGCR0, val);
} else if (IS_GEN9_BC(dev_priv)) {
/* DDI -> PLL mapping */
val = I915_READ(DPLL_CTRL2);
val &= ~(DPLL_CTRL2_DDI_CLK_OFF(port) |
DPLL_CTRL2_DDI_CLK_SEL_MASK(port));
val |= (DPLL_CTRL2_DDI_CLK_SEL(pll->id, port) |
DPLL_CTRL2_DDI_SEL_OVERRIDE(port));
I915_WRITE(DPLL_CTRL2, val);
} else if (INTEL_INFO(dev_priv)->gen < 9) {
I915_WRITE(PORT_CLK_SEL(port), hsw_pll_to_ddi_pll_sel(pll));
}
}
static void intel_ddi_pre_enable_dp(struct intel_encoder *encoder,
int link_rate, uint32_t lane_count,
struct intel_shared_dpll *pll,
bool link_mst)
{
struct intel_dp *intel_dp = enc_to_intel_dp(&encoder->base);
struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
enum port port = intel_ddi_get_encoder_port(encoder);
struct intel_digital_port *dig_port = enc_to_dig_port(&encoder->base);
WARN_ON(link_mst && (port == PORT_A || port == PORT_E));
intel_dp_set_link_params(intel_dp, link_rate, lane_count,
link_mst);
if (encoder->type == INTEL_OUTPUT_EDP)
intel_edp_panel_on(intel_dp);
intel_ddi_clk_select(encoder, pll);
intel_display_power_get(dev_priv, dig_port->ddi_io_power_domain);
intel_prepare_dp_ddi_buffers(encoder);
intel_ddi_init_dp_buf_reg(encoder);
intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_ON);
intel_dp_start_link_train(intel_dp);
if (port != PORT_A || INTEL_GEN(dev_priv) >= 9)
intel_dp_stop_link_train(intel_dp);
}
static void intel_ddi_pre_enable_hdmi(struct intel_encoder *encoder,
bool has_infoframe,
const struct intel_crtc_state *crtc_state,
const struct drm_connector_state *conn_state,
struct intel_shared_dpll *pll)
{
struct intel_digital_port *intel_dig_port = enc_to_dig_port(&encoder->base);
struct intel_hdmi *intel_hdmi = &intel_dig_port->hdmi;
struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
enum port port = intel_ddi_get_encoder_port(encoder);
int level = intel_ddi_hdmi_level(dev_priv, port);
struct intel_digital_port *dig_port = enc_to_dig_port(&encoder->base);
intel_dp_dual_mode_set_tmds_output(intel_hdmi, true);
intel_ddi_clk_select(encoder, pll);
intel_display_power_get(dev_priv, dig_port->ddi_io_power_domain);
intel_prepare_hdmi_ddi_buffers(encoder);
if (IS_GEN9_BC(dev_priv))
skl_ddi_set_iboost(encoder, level);
else if (IS_GEN9_LP(dev_priv))
bxt_ddi_vswing_sequence(dev_priv, level, port,
INTEL_OUTPUT_HDMI);
else if (IS_CANNONLAKE(dev_priv))
cnl_ddi_vswing_sequence(encoder, level);
intel_dig_port->set_infoframes(&encoder->base,
has_infoframe,
crtc_state, conn_state);
}
static void intel_ddi_pre_enable(struct intel_encoder *encoder,
struct intel_crtc_state *pipe_config,
struct drm_connector_state *conn_state)
{
int type = encoder->type;
if (type == INTEL_OUTPUT_DP || type == INTEL_OUTPUT_EDP) {
intel_ddi_pre_enable_dp(encoder,
pipe_config->port_clock,
pipe_config->lane_count,
pipe_config->shared_dpll,
intel_crtc_has_type(pipe_config,
INTEL_OUTPUT_DP_MST));
}
if (type == INTEL_OUTPUT_HDMI) {
intel_ddi_pre_enable_hdmi(encoder,
pipe_config->has_infoframe,
pipe_config, conn_state,
pipe_config->shared_dpll);
}
}
static void intel_ddi_post_disable(struct intel_encoder *intel_encoder,
struct intel_crtc_state *old_crtc_state,
struct drm_connector_state *old_conn_state)
{
struct drm_encoder *encoder = &intel_encoder->base;
struct drm_i915_private *dev_priv = to_i915(encoder->dev);
enum port port = intel_ddi_get_encoder_port(intel_encoder);
struct intel_digital_port *dig_port = enc_to_dig_port(encoder);
int type = intel_encoder->type;
uint32_t val;
bool wait = false;
/* old_crtc_state and old_conn_state are NULL when called from DP_MST */
drm/i915/ddi: Avoid long delays during system suspend / eDP disabling Atm disabling either DP or eDP outputs can generate a spurious short pulse interrupt. The reason is that after disabling the port the source will stop sending a valid stream data, while the sink expects either a valid stream or the idle pattern. Since neither of this is sent the sink assumes (after an arbitrary delay) that the link is lost and requests for link retraining with a short pulse. The spurious pulse is a real problem at least for eDP panels with long power-off / power-cycle delays: as part of disabling the output we disable the panel power. The subsequent spurious short pulse handling will have to turn the power back on, which means the driver has to do a redundant wait for the power-off and power-cycle delays. During system suspend this leads to an unnecessary delay up to ~1s on systems with such panels as reported by Rui. To fix this put the sink to DPMS D3 state before turning off the port. According to the DP spec in this state the sink should not request retraining. This is also what we do already on pre-ddi platforms. As an alternative I also tried configuring the port to send idle pattern - which is against BSPec - and leave the port in normal mode before turning off the port. Neither of these resolved the problem. Cc: Zhang Rui <rui.zhang@intel.com> Cc: David Weinehall <david.weinehall@linux.intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reported-and-tested-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1496250335-7627-1-git-send-email-imre.deak@intel.com
2017-05-31 17:05:35 +00:00
if (type == INTEL_OUTPUT_DP || type == INTEL_OUTPUT_EDP) {
struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
drm/i915/ddi: Avoid long delays during system suspend / eDP disabling Atm disabling either DP or eDP outputs can generate a spurious short pulse interrupt. The reason is that after disabling the port the source will stop sending a valid stream data, while the sink expects either a valid stream or the idle pattern. Since neither of this is sent the sink assumes (after an arbitrary delay) that the link is lost and requests for link retraining with a short pulse. The spurious pulse is a real problem at least for eDP panels with long power-off / power-cycle delays: as part of disabling the output we disable the panel power. The subsequent spurious short pulse handling will have to turn the power back on, which means the driver has to do a redundant wait for the power-off and power-cycle delays. During system suspend this leads to an unnecessary delay up to ~1s on systems with such panels as reported by Rui. To fix this put the sink to DPMS D3 state before turning off the port. According to the DP spec in this state the sink should not request retraining. This is also what we do already on pre-ddi platforms. As an alternative I also tried configuring the port to send idle pattern - which is against BSPec - and leave the port in normal mode before turning off the port. Neither of these resolved the problem. Cc: Zhang Rui <rui.zhang@intel.com> Cc: David Weinehall <david.weinehall@linux.intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reported-and-tested-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1496250335-7627-1-git-send-email-imre.deak@intel.com
2017-05-31 17:05:35 +00:00
intel_dp_sink_dpms(intel_dp, DRM_MODE_DPMS_OFF);
}
val = I915_READ(DDI_BUF_CTL(port));
if (val & DDI_BUF_CTL_ENABLE) {
val &= ~DDI_BUF_CTL_ENABLE;
I915_WRITE(DDI_BUF_CTL(port), val);
wait = true;
}
val = I915_READ(DP_TP_CTL(port));
val &= ~(DP_TP_CTL_ENABLE | DP_TP_CTL_LINK_TRAIN_MASK);
val |= DP_TP_CTL_LINK_TRAIN_PAT1;
I915_WRITE(DP_TP_CTL(port), val);
if (wait)
intel_wait_ddi_buf_idle(dev_priv, port);
if (type == INTEL_OUTPUT_HDMI) {
dig_port->set_infoframes(encoder, false,
old_crtc_state, old_conn_state);
}
if (type == INTEL_OUTPUT_DP || type == INTEL_OUTPUT_EDP) {
struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
drm/i915: finish off reverting eDP VDD changes This is a small follow-up fix to the series of eDP VDD back and forth we've had recently. This is effectively a combined revert of three commits: commit 2c2894f698fffd8ff53e1e1d3834f9e1035b1f39 Author: Paulo Zanoni <paulo.r.zanoni@intel.com> Date: Fri Mar 7 20:05:20 2014 -0300 drm/i915: properly disable the VDD when disabling the panel commit b3064154dfd37deb386b1e459c54e1ca2460b3d5 Author: Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Date: Tue Mar 4 00:42:44 2014 +0100 drm/i915: Don't just say it, actually force edp vdd commit dff392dbd258381a6c3164f38420593f2d291e3b Author: Paulo Zanoni <paulo.r.zanoni@intel.com> Date: Fri Dec 6 17:32:41 2013 -0200 drm/i915: don't touch the VDD when disabling the panel which shows that we're pretty close back to where we started already. The first two were basically reverting the last, but missing the WARN. Add that back. We also OCD the intel_ prefix back to intel_edp_panel_vdd_on() which was lost somewhere in between. The circle closes. For future reference, "drm/i915: don't touch the VDD when disabling the panel" failed to take into account commit 6cb49835da0426f69a2931bc2a0a8156344b0e41 Author: Daniel Vetter <daniel.vetter@ffwll.ch> Date: Sun May 20 17:14:50 2012 +0200 drm/i915: enable vdd when switching off the eDP panel and commit 35a38556d900b9cb5dfa2529c93944b847f8a8a4 Author: Daniel Vetter <daniel.vetter@ffwll.ch> Date: Sun Aug 12 22:17:14 2012 +0200 drm/i915: reorder edp disabling to fix ivb MacBook Air Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2014-03-17 14:43:36 +00:00
intel_edp_panel_vdd_on(intel_dp);
intel_edp_panel_off(intel_dp);
}
if (dig_port)
intel_display_power_put(dev_priv, dig_port->ddi_io_power_domain);
if (IS_CANNONLAKE(dev_priv))
I915_WRITE(DPCLKA_CFGCR0, I915_READ(DPCLKA_CFGCR0) |
DPCLKA_CFGCR0_DDI_CLK_OFF(port));
else if (IS_GEN9_BC(dev_priv))
I915_WRITE(DPLL_CTRL2, (I915_READ(DPLL_CTRL2) |
DPLL_CTRL2_DDI_CLK_OFF(port)));
else if (INTEL_GEN(dev_priv) < 9)
I915_WRITE(PORT_CLK_SEL(port), PORT_CLK_SEL_NONE);
if (type == INTEL_OUTPUT_HDMI) {
struct intel_hdmi *intel_hdmi = enc_to_intel_hdmi(encoder);
intel_dp_dual_mode_set_tmds_output(intel_hdmi, false);
}
}
void intel_ddi_fdi_post_disable(struct intel_encoder *encoder,
struct intel_crtc_state *old_crtc_state,
struct drm_connector_state *old_conn_state)
{
struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
uint32_t val;
/*
* Bspec lists this as both step 13 (before DDI_BUF_CTL disable)
* and step 18 (after clearing PORT_CLK_SEL). Based on a BUN,
* step 13 is the correct place for it. Step 18 is where it was
* originally before the BUN.
*/
val = I915_READ(FDI_RX_CTL(PIPE_A));
val &= ~FDI_RX_ENABLE;
I915_WRITE(FDI_RX_CTL(PIPE_A), val);
intel_ddi_post_disable(encoder, old_crtc_state, old_conn_state);
val = I915_READ(FDI_RX_MISC(PIPE_A));
val &= ~(FDI_RX_PWRDN_LANE1_MASK | FDI_RX_PWRDN_LANE0_MASK);
val |= FDI_RX_PWRDN_LANE1_VAL(2) | FDI_RX_PWRDN_LANE0_VAL(2);
I915_WRITE(FDI_RX_MISC(PIPE_A), val);
val = I915_READ(FDI_RX_CTL(PIPE_A));
val &= ~FDI_PCDCLK;
I915_WRITE(FDI_RX_CTL(PIPE_A), val);
val = I915_READ(FDI_RX_CTL(PIPE_A));
val &= ~FDI_RX_PLL_ENABLE;
I915_WRITE(FDI_RX_CTL(PIPE_A), val);
}
static void intel_enable_ddi(struct intel_encoder *intel_encoder,
struct intel_crtc_state *pipe_config,
struct drm_connector_state *conn_state)
{
struct drm_encoder *encoder = &intel_encoder->base;
struct drm_i915_private *dev_priv = to_i915(encoder->dev);
enum port port = intel_ddi_get_encoder_port(intel_encoder);
int type = intel_encoder->type;
if (type == INTEL_OUTPUT_HDMI) {
struct intel_digital_port *intel_dig_port =
enc_to_dig_port(encoder);
drm/i915: enable scrambling Geminilake platform sports a native HDMI 2.0 controller, and is capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec mendates scrambling for these higher clocks, for reduced RF footprint. This patch checks if the monitor supports scrambling, and if required, enables it during the modeset. V2: Addressed review comments from Ville: - Do not track scrambling status in DRM layer, track somewhere in driver like in intel_crtc_state. - Don't talk to monitor at such a low layer, set monitor scrambling in intel_enable_ddi() before enabling the port. V3: Addressed review comments from Jani - In comments, function names, use "sink" instead of "monitor", so that the implementation could be close to the language of HDMI spec. V4: Addressed review comment from Maarten - scrambling -> hdmi_scrambling - high_tmds_clock_ratio -> hdmi_high_tmds_clock_ratio V5: Addressed review comments from Ville and Ander - Do not modifiy the crtc_state after compute_config. Move all scrambling and tmds_clock_ratio calcutations to compute_config. - While setting scrambling for source/sink, do not check the conditions again, just go by the crtc_state flags. This will simplyfy the condition checks. V6: Addressed review comments from Ville - Do not add IS_GLK check in disable/enable function, instead add it in compute_config, while setting state flags. - Remove unnecessary paranthesis. - Simplyfy handle_sink_scrambling function as suggested. - Add readout code for scrambling status in get_ddi_config and add a check for the same in pipe_config_compare. V7: Addressed review comments from Ander/Ville - No separate function for source scrambling, make it inline - Align the last line of the macro TRANS_DDI_HDMI_SCRAMBLING_MASK - Do not add platform check while setting source scrambling - Use pipe_config instead of crtc->config to set sink scrambling - To readout scrambling status, Compare with SCRAMBLING_MASK not any of its bits - Remove platform check in intel_pipe_config_compare while checking scrambling status V8: Fixed mege conflict, Addressed review comments from Ander - Remove the desciption/comment about scrambling fom the caller, move it to the function - Move the IS_GLK check into scrambling function - Fix alignment V9: Fixed review comments from Ville, Ander - Pass the scrambling state variables as bool input to the sink_scrambling function and let the disable call be unconditional. - Fix alignments in function calls and debug messages. - Add kernel doc for function intel_hdmi_handle_sink_scrambling V10: Rebase Signed-off-by: Shashank Sharma <shashank.sharma@intel.com> Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1489404244-16608-6-git-send-email-shashank.sharma@intel.com
2017-03-13 11:24:03 +00:00
bool clock_ratio = pipe_config->hdmi_high_tmds_clock_ratio;
bool scrambling = pipe_config->hdmi_scrambling;
intel_hdmi_handle_sink_scrambling(intel_encoder,
conn_state->connector,
clock_ratio, scrambling);
/* In HDMI/DVI mode, the port width, and swing/emphasis values
* are ignored so nothing special needs to be done besides
* enabling the port.
*/
I915_WRITE(DDI_BUF_CTL(port),
intel_dig_port->saved_port_bits |
DDI_BUF_CTL_ENABLE);
} else if (type == INTEL_OUTPUT_EDP) {
struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
if (port == PORT_A && INTEL_GEN(dev_priv) < 9)
drm/i915: hsw: fix link training for eDP on port-A According to BSpec the link training sequence for eDP on HSW port-A should be as follows: 1. link training: clock recovery 2. link training: equalization 3. link training: set idle transmission mode 4. display pipe enable 5. link training: disable (set normal mode) Contrary to this at the moment we don't do step 3. and we do step 5. before step 4. Fix this by setting idle transmission mode for eDP at the end of intel_dp_complete_link_train and adding a new intel_dp_stop_link_training function to disable link training. With these changes we'll end up with the following functions corresponding to the above steps: intel_dp_start_link_train -> step 1. intel_dp_complete_link_train -> step 2., step 3. intel_dp_stop_link_train -> step 5. For port-A we'll call intel_dp_stop_link_train only after enabling the pipe, for everything else we'll call it right after intel_dp_complete_link_train to preserve the current behavior. Tested on HSW/HSW-ULT. In v2: - Due to a HW issue we must set idle transmission mode for port-A too before enabling the pipe. Thanks for Arthur Runyan for explaining this. - Update the patch subject to make it clear that it's an eDP fix, DP is not affected. v3: - rename intel_dp_link_train() to intel_dp_set_link_train(), use 'val' instead 'l' as var name. (Paulo) Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2013-05-03 09:57:41 +00:00
intel_dp_stop_link_train(intel_dp);
intel_edp_backlight_on(pipe_config, conn_state);
intel_psr_enable(intel_dp);
intel_edp_drrs_enable(intel_dp, pipe_config);
}
drm/i915: Fix POWER_DOMAIN_AUDIO refcounting. If the crtc was brought up with audio before the driver loads, then crtc_disable will remove a refcount to audio that doesn't exist before. Fortunately we already set power domains on readout, so we can just add the power domain handling to get_crtc_power_domains, which will update the power domains correctly in all cases. This was found when testing module reload on CI with the crtc enabled, which resulted in the following warn after module reload + modeset: [ 24.197041] ------------[ cut here ]------------ [ 24.197075] WARNING: CPU: 0 PID: 99 at drivers/gpu/drm/i915/intel_runtime_pm.c:1790 intel_display_power_put+0x134/0x140 [i915] [ 24.197076] Use count on domain AUDIO is already zero [ 24.197098] CPU: 0 PID: 99 Comm: kworker/u8:2 Not tainted 4.9.0-CI-Trybot_393+ #1 [ 24.197099] Hardware name: /NUC6i5SYB, BIOS SYSKLi35.86A.0042.2016.0409.1246 04/09/2016 [ 24.197102] Workqueue: events_unbound async_run_entry_fn [ 24.197105] ffffc900003c7688 ffffffff81435b35 ffffc900003c76d8 0000000000000000 [ 24.197107] ffffc900003c76c8 ffffffff8107e4d6 000006fe5dc36f28 ffff88025dc30054 [ 24.197109] ffff88025dc36f28 ffff88025dc30000 ffff88025dc30000 0000000000000015 [ 24.197110] Call Trace: [ 24.197113] [<ffffffff81435b35>] dump_stack+0x67/0x92 [ 24.197116] [<ffffffff8107e4d6>] __warn+0xc6/0xe0 [ 24.197118] [<ffffffff8107e53a>] warn_slowpath_fmt+0x4a/0x50 [ 24.197149] [<ffffffffa039b4b4>] intel_display_power_put+0x134/0x140 [i915] [ 24.197187] [<ffffffffa04217dd>] intel_disable_ddi+0x4d/0x80 [i915] [ 24.197223] [<ffffffffa03f388f>] intel_encoders_disable.isra.74+0x7f/0x90 [i915] [ 24.197257] [<ffffffffa03f6c05>] haswell_crtc_disable+0x55/0x170 [i915] [ 24.197292] [<ffffffffa03fec88>] intel_atomic_commit_tail+0x108/0xfd0 [i915] [ 24.197295] [<ffffffff810d47c6>] ? __lock_is_held+0x66/0x90 [ 24.197330] [<ffffffffa03fff79>] intel_atomic_commit+0x429/0x560 [i915] [ 24.197332] [<ffffffff81570186>] ?drm_atomic_add_affected_connectors+0x56/0xf0 [ 24.197334] [<ffffffff8156f726>] drm_atomic_commit+0x46/0x50 [ 24.197336] [<ffffffff81553f87>] restore_fbdev_mode+0x147/0x270 [ 24.197337] [<ffffffff81555bee>] drm_fb_helper_restore_fbdev_mode_unlocked+0x2e/0x70 [ 24.197339] [<ffffffff81555aa8>] drm_fb_helper_set_par+0x28/0x50 [ 24.197374] [<ffffffffa041c7d3>] intel_fbdev_set_par+0x13/0x70 [i915] [ 24.197376] [<ffffffff8149e07a>] fbcon_init+0x57a/0x600 [ 24.197379] [<ffffffff81514b71>] visual_init+0xd1/0x130 [ 24.197381] [<ffffffff8151603c>] do_bind_con_driver+0x1bc/0x3a0 [ 24.197384] [<ffffffff81516521>] do_take_over_console+0x111/0x180 [ 24.197386] [<ffffffff8149e152>] do_fbcon_takeover+0x52/0xb0 [ 24.197387] [<ffffffff814a12c3>] fbcon_event_notify+0x723/0x850 [ 24.197390] [<ffffffff810a4830>] ?__blocking_notifier_call_chain+0x30/0x70 [ 24.197392] [<ffffffff810a44a4>] notifier_call_chain+0x34/0xa0 [ 24.197394] [<ffffffff810a4848>] __blocking_notifier_call_chain+0x48/0x70 [ 24.197397] [<ffffffff810a4881>] blocking_notifier_call_chain+0x11/0x20 [ 24.197398] [<ffffffff814a4556>] fb_notifier_call_chain+0x16/0x20 [ 24.197400] [<ffffffff814a678c>] register_framebuffer+0x24c/0x330 [ 24.197402] [<ffffffff815558d9>] drm_fb_helper_initial_config+0x219/0x3c0 [ 24.197436] [<ffffffffa041d373>] intel_fbdev_initial_config+0x13/0x30 [i915] [ 24.197438] [<ffffffff810a5d44>] async_run_entry_fn+0x34/0x140 [ 24.197440] [<ffffffff8109c26c>] process_one_work+0x1ec/0x6b0 [ 24.197442] [<ffffffff8109c1e6>] ? process_one_work+0x166/0x6b0 [ 24.197445] [<ffffffff8109c779>] worker_thread+0x49/0x490 [ 24.197447] [<ffffffff8109c730>] ? process_one_work+0x6b0/0x6b0 [ 24.197448] [<ffffffff810a2a9b>] kthread+0xeb/0x110 [ 24.197451] [<ffffffff810a29b0>] ? kthread_park+0x60/0x60 [ 24.197453] [<ffffffff818241a7>] ret_from_fork+0x27/0x40 [ 24.197476] ---[ end trace bda64b683b8e8162 ]--- Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1481812185-19098-3-git-send-email-maarten.lankhorst@linux.intel.com Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2016-12-15 14:29:43 +00:00
if (pipe_config->has_audio)
intel_audio_codec_enable(intel_encoder, pipe_config, conn_state);
drm/i915/hdmi: convert to encoder->disable/enable I've picked hdmi as the first encoder to convert because it's rather simple: - no cloning possible - no differences between prepare/commit and dpms off/on switching. A few changes are required to do so: - Split up the dpms code into an enable/disable function and wire it up with the intel encoder. - Noop out the existing encoder prepare/commit functions used by the crtc helper - our crtc enable/disable code now calls back into the encoder enable/disable code at the right spot. - Create new helper functions to handle dpms changes. - Add intel_encoder->connectors_active to better track dpms state. Atm this is unused, but it will be useful to correctly disable the entire display pipe for cloned configurations. Also note that for now this is only useful in the dpms code - thanks to the crtc helper's dpms confusion across a modeset operation we can't (yet) rely on this having a sensible value in all circumstances. - Rip out the encoder helper dpms callback, if this is still getting called somewhere we have a bug. The slight issue with that is that the crtc helper abuses dpms off to disable unused functions. Hence we also need to implement a default encoder disable function to do just that with the new encoder->disable callback. - Note that we drop the cpt modeset verification in the commit callback, too. The right place to do this would be in the crtc's enable function, _after_ all the encoders are set up. But because not all encoders are converted yet, we can't do that. Hence disable this check temporarily as a minor concession to bisectability. v2: Squash the dpms mode to only the supported values - connector->dpms is for internal tracking only, we can hence avoid needless state-changes a bit whithout causing harm. v3: Apply bikeshed to disable|enable_ddi, suggested by Paulo Zanoni. Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2012-06-30 06:59:56 +00:00
}
static void intel_disable_ddi(struct intel_encoder *intel_encoder,
struct intel_crtc_state *old_crtc_state,
struct drm_connector_state *old_conn_state)
drm/i915/hdmi: convert to encoder->disable/enable I've picked hdmi as the first encoder to convert because it's rather simple: - no cloning possible - no differences between prepare/commit and dpms off/on switching. A few changes are required to do so: - Split up the dpms code into an enable/disable function and wire it up with the intel encoder. - Noop out the existing encoder prepare/commit functions used by the crtc helper - our crtc enable/disable code now calls back into the encoder enable/disable code at the right spot. - Create new helper functions to handle dpms changes. - Add intel_encoder->connectors_active to better track dpms state. Atm this is unused, but it will be useful to correctly disable the entire display pipe for cloned configurations. Also note that for now this is only useful in the dpms code - thanks to the crtc helper's dpms confusion across a modeset operation we can't (yet) rely on this having a sensible value in all circumstances. - Rip out the encoder helper dpms callback, if this is still getting called somewhere we have a bug. The slight issue with that is that the crtc helper abuses dpms off to disable unused functions. Hence we also need to implement a default encoder disable function to do just that with the new encoder->disable callback. - Note that we drop the cpt modeset verification in the commit callback, too. The right place to do this would be in the crtc's enable function, _after_ all the encoders are set up. But because not all encoders are converted yet, we can't do that. Hence disable this check temporarily as a minor concession to bisectability. v2: Squash the dpms mode to only the supported values - connector->dpms is for internal tracking only, we can hence avoid needless state-changes a bit whithout causing harm. v3: Apply bikeshed to disable|enable_ddi, suggested by Paulo Zanoni. Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2012-06-30 06:59:56 +00:00
{
struct drm_encoder *encoder = &intel_encoder->base;
int type = intel_encoder->type;
drm/i915: Fix POWER_DOMAIN_AUDIO refcounting. If the crtc was brought up with audio before the driver loads, then crtc_disable will remove a refcount to audio that doesn't exist before. Fortunately we already set power domains on readout, so we can just add the power domain handling to get_crtc_power_domains, which will update the power domains correctly in all cases. This was found when testing module reload on CI with the crtc enabled, which resulted in the following warn after module reload + modeset: [ 24.197041] ------------[ cut here ]------------ [ 24.197075] WARNING: CPU: 0 PID: 99 at drivers/gpu/drm/i915/intel_runtime_pm.c:1790 intel_display_power_put+0x134/0x140 [i915] [ 24.197076] Use count on domain AUDIO is already zero [ 24.197098] CPU: 0 PID: 99 Comm: kworker/u8:2 Not tainted 4.9.0-CI-Trybot_393+ #1 [ 24.197099] Hardware name: /NUC6i5SYB, BIOS SYSKLi35.86A.0042.2016.0409.1246 04/09/2016 [ 24.197102] Workqueue: events_unbound async_run_entry_fn [ 24.197105] ffffc900003c7688 ffffffff81435b35 ffffc900003c76d8 0000000000000000 [ 24.197107] ffffc900003c76c8 ffffffff8107e4d6 000006fe5dc36f28 ffff88025dc30054 [ 24.197109] ffff88025dc36f28 ffff88025dc30000 ffff88025dc30000 0000000000000015 [ 24.197110] Call Trace: [ 24.197113] [<ffffffff81435b35>] dump_stack+0x67/0x92 [ 24.197116] [<ffffffff8107e4d6>] __warn+0xc6/0xe0 [ 24.197118] [<ffffffff8107e53a>] warn_slowpath_fmt+0x4a/0x50 [ 24.197149] [<ffffffffa039b4b4>] intel_display_power_put+0x134/0x140 [i915] [ 24.197187] [<ffffffffa04217dd>] intel_disable_ddi+0x4d/0x80 [i915] [ 24.197223] [<ffffffffa03f388f>] intel_encoders_disable.isra.74+0x7f/0x90 [i915] [ 24.197257] [<ffffffffa03f6c05>] haswell_crtc_disable+0x55/0x170 [i915] [ 24.197292] [<ffffffffa03fec88>] intel_atomic_commit_tail+0x108/0xfd0 [i915] [ 24.197295] [<ffffffff810d47c6>] ? __lock_is_held+0x66/0x90 [ 24.197330] [<ffffffffa03fff79>] intel_atomic_commit+0x429/0x560 [i915] [ 24.197332] [<ffffffff81570186>] ?drm_atomic_add_affected_connectors+0x56/0xf0 [ 24.197334] [<ffffffff8156f726>] drm_atomic_commit+0x46/0x50 [ 24.197336] [<ffffffff81553f87>] restore_fbdev_mode+0x147/0x270 [ 24.197337] [<ffffffff81555bee>] drm_fb_helper_restore_fbdev_mode_unlocked+0x2e/0x70 [ 24.197339] [<ffffffff81555aa8>] drm_fb_helper_set_par+0x28/0x50 [ 24.197374] [<ffffffffa041c7d3>] intel_fbdev_set_par+0x13/0x70 [i915] [ 24.197376] [<ffffffff8149e07a>] fbcon_init+0x57a/0x600 [ 24.197379] [<ffffffff81514b71>] visual_init+0xd1/0x130 [ 24.197381] [<ffffffff8151603c>] do_bind_con_driver+0x1bc/0x3a0 [ 24.197384] [<ffffffff81516521>] do_take_over_console+0x111/0x180 [ 24.197386] [<ffffffff8149e152>] do_fbcon_takeover+0x52/0xb0 [ 24.197387] [<ffffffff814a12c3>] fbcon_event_notify+0x723/0x850 [ 24.197390] [<ffffffff810a4830>] ?__blocking_notifier_call_chain+0x30/0x70 [ 24.197392] [<ffffffff810a44a4>] notifier_call_chain+0x34/0xa0 [ 24.197394] [<ffffffff810a4848>] __blocking_notifier_call_chain+0x48/0x70 [ 24.197397] [<ffffffff810a4881>] blocking_notifier_call_chain+0x11/0x20 [ 24.197398] [<ffffffff814a4556>] fb_notifier_call_chain+0x16/0x20 [ 24.197400] [<ffffffff814a678c>] register_framebuffer+0x24c/0x330 [ 24.197402] [<ffffffff815558d9>] drm_fb_helper_initial_config+0x219/0x3c0 [ 24.197436] [<ffffffffa041d373>] intel_fbdev_initial_config+0x13/0x30 [i915] [ 24.197438] [<ffffffff810a5d44>] async_run_entry_fn+0x34/0x140 [ 24.197440] [<ffffffff8109c26c>] process_one_work+0x1ec/0x6b0 [ 24.197442] [<ffffffff8109c1e6>] ? process_one_work+0x166/0x6b0 [ 24.197445] [<ffffffff8109c779>] worker_thread+0x49/0x490 [ 24.197447] [<ffffffff8109c730>] ? process_one_work+0x6b0/0x6b0 [ 24.197448] [<ffffffff810a2a9b>] kthread+0xeb/0x110 [ 24.197451] [<ffffffff810a29b0>] ? kthread_park+0x60/0x60 [ 24.197453] [<ffffffff818241a7>] ret_from_fork+0x27/0x40 [ 24.197476] ---[ end trace bda64b683b8e8162 ]--- Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1481812185-19098-3-git-send-email-maarten.lankhorst@linux.intel.com Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2016-12-15 14:29:43 +00:00
if (old_crtc_state->has_audio)
intel_audio_codec_disable(intel_encoder);
drm/i915: enable scrambling Geminilake platform sports a native HDMI 2.0 controller, and is capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec mendates scrambling for these higher clocks, for reduced RF footprint. This patch checks if the monitor supports scrambling, and if required, enables it during the modeset. V2: Addressed review comments from Ville: - Do not track scrambling status in DRM layer, track somewhere in driver like in intel_crtc_state. - Don't talk to monitor at such a low layer, set monitor scrambling in intel_enable_ddi() before enabling the port. V3: Addressed review comments from Jani - In comments, function names, use "sink" instead of "monitor", so that the implementation could be close to the language of HDMI spec. V4: Addressed review comment from Maarten - scrambling -> hdmi_scrambling - high_tmds_clock_ratio -> hdmi_high_tmds_clock_ratio V5: Addressed review comments from Ville and Ander - Do not modifiy the crtc_state after compute_config. Move all scrambling and tmds_clock_ratio calcutations to compute_config. - While setting scrambling for source/sink, do not check the conditions again, just go by the crtc_state flags. This will simplyfy the condition checks. V6: Addressed review comments from Ville - Do not add IS_GLK check in disable/enable function, instead add it in compute_config, while setting state flags. - Remove unnecessary paranthesis. - Simplyfy handle_sink_scrambling function as suggested. - Add readout code for scrambling status in get_ddi_config and add a check for the same in pipe_config_compare. V7: Addressed review comments from Ander/Ville - No separate function for source scrambling, make it inline - Align the last line of the macro TRANS_DDI_HDMI_SCRAMBLING_MASK - Do not add platform check while setting source scrambling - Use pipe_config instead of crtc->config to set sink scrambling - To readout scrambling status, Compare with SCRAMBLING_MASK not any of its bits - Remove platform check in intel_pipe_config_compare while checking scrambling status V8: Fixed mege conflict, Addressed review comments from Ander - Remove the desciption/comment about scrambling fom the caller, move it to the function - Move the IS_GLK check into scrambling function - Fix alignment V9: Fixed review comments from Ville, Ander - Pass the scrambling state variables as bool input to the sink_scrambling function and let the disable call be unconditional. - Fix alignments in function calls and debug messages. - Add kernel doc for function intel_hdmi_handle_sink_scrambling V10: Rebase Signed-off-by: Shashank Sharma <shashank.sharma@intel.com> Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1489404244-16608-6-git-send-email-shashank.sharma@intel.com
2017-03-13 11:24:03 +00:00
if (type == INTEL_OUTPUT_HDMI) {
intel_hdmi_handle_sink_scrambling(intel_encoder,
old_conn_state->connector,
false, false);
}
if (type == INTEL_OUTPUT_EDP) {
struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
intel_edp_drrs_disable(intel_dp, old_crtc_state);
intel_psr_disable(intel_dp);
intel_edp_backlight_off(old_conn_state);
}
}
static void bxt_ddi_pre_pll_enable(struct intel_encoder *encoder,
struct intel_crtc_state *pipe_config,
struct drm_connector_state *conn_state)
{
uint8_t mask = pipe_config->lane_lat_optim_mask;
bxt_ddi_phy_set_lane_optim_mask(encoder, mask);
}
void intel_ddi_prepare_link_retrain(struct intel_dp *intel_dp)
{
struct intel_digital_port *intel_dig_port = dp_to_dig_port(intel_dp);
struct drm_i915_private *dev_priv =
to_i915(intel_dig_port->base.base.dev);
enum port port = intel_dig_port->port;
uint32_t val;
bool wait = false;
if (I915_READ(DP_TP_CTL(port)) & DP_TP_CTL_ENABLE) {
val = I915_READ(DDI_BUF_CTL(port));
if (val & DDI_BUF_CTL_ENABLE) {
val &= ~DDI_BUF_CTL_ENABLE;
I915_WRITE(DDI_BUF_CTL(port), val);
wait = true;
}
val = I915_READ(DP_TP_CTL(port));
val &= ~(DP_TP_CTL_ENABLE | DP_TP_CTL_LINK_TRAIN_MASK);
val |= DP_TP_CTL_LINK_TRAIN_PAT1;
I915_WRITE(DP_TP_CTL(port), val);
POSTING_READ(DP_TP_CTL(port));
if (wait)
intel_wait_ddi_buf_idle(dev_priv, port);
}
2014-05-02 04:02:48 +00:00
val = DP_TP_CTL_ENABLE |
DP_TP_CTL_LINK_TRAIN_PAT1 | DP_TP_CTL_SCRAMBLE_DISABLE;
if (intel_dp->link_mst)
2014-05-02 04:02:48 +00:00
val |= DP_TP_CTL_MODE_MST;
else {
val |= DP_TP_CTL_MODE_SST;
if (drm_dp_enhanced_frame_cap(intel_dp->dpcd))
val |= DP_TP_CTL_ENHANCED_FRAME_ENABLE;
}
I915_WRITE(DP_TP_CTL(port), val);
POSTING_READ(DP_TP_CTL(port));
intel_dp->DP |= DDI_BUF_CTL_ENABLE;
I915_WRITE(DDI_BUF_CTL(port), intel_dp->DP);
POSTING_READ(DDI_BUF_CTL(port));
udelay(600);
}
bool intel_ddi_is_audio_enabled(struct drm_i915_private *dev_priv,
struct intel_crtc *intel_crtc)
{
u32 temp;
if (intel_display_power_is_enabled(dev_priv, POWER_DOMAIN_AUDIO)) {
temp = I915_READ(HSW_AUD_PIN_ELD_CP_VLD);
if (temp & AUDIO_OUTPUT_ENABLE(intel_crtc->pipe))
return true;
}
return false;
}
void intel_ddi_get_config(struct intel_encoder *encoder,
struct intel_crtc_state *pipe_config)
{
struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
struct intel_crtc *intel_crtc = to_intel_crtc(encoder->base.crtc);
enum transcoder cpu_transcoder = pipe_config->cpu_transcoder;
struct intel_digital_port *intel_dig_port;
u32 temp, flags = 0;
/* XXX: DSI transcoder paranoia */
if (WARN_ON(transcoder_is_dsi(cpu_transcoder)))
return;
temp = I915_READ(TRANS_DDI_FUNC_CTL(cpu_transcoder));
if (temp & TRANS_DDI_PHSYNC)
flags |= DRM_MODE_FLAG_PHSYNC;
else
flags |= DRM_MODE_FLAG_NHSYNC;
if (temp & TRANS_DDI_PVSYNC)
flags |= DRM_MODE_FLAG_PVSYNC;
else
flags |= DRM_MODE_FLAG_NVSYNC;
pipe_config->base.adjusted_mode.flags |= flags;
switch (temp & TRANS_DDI_BPC_MASK) {
case TRANS_DDI_BPC_6:
pipe_config->pipe_bpp = 18;
break;
case TRANS_DDI_BPC_8:
pipe_config->pipe_bpp = 24;
break;
case TRANS_DDI_BPC_10:
pipe_config->pipe_bpp = 30;
break;
case TRANS_DDI_BPC_12:
pipe_config->pipe_bpp = 36;
break;
default:
break;
}
switch (temp & TRANS_DDI_MODE_SELECT_MASK) {
case TRANS_DDI_MODE_SELECT_HDMI:
pipe_config->has_hdmi_sink = true;
intel_dig_port = enc_to_dig_port(&encoder->base);
if (intel_dig_port->infoframe_enabled(&encoder->base, pipe_config))
pipe_config->has_infoframe = true;
drm/i915: enable scrambling Geminilake platform sports a native HDMI 2.0 controller, and is capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec mendates scrambling for these higher clocks, for reduced RF footprint. This patch checks if the monitor supports scrambling, and if required, enables it during the modeset. V2: Addressed review comments from Ville: - Do not track scrambling status in DRM layer, track somewhere in driver like in intel_crtc_state. - Don't talk to monitor at such a low layer, set monitor scrambling in intel_enable_ddi() before enabling the port. V3: Addressed review comments from Jani - In comments, function names, use "sink" instead of "monitor", so that the implementation could be close to the language of HDMI spec. V4: Addressed review comment from Maarten - scrambling -> hdmi_scrambling - high_tmds_clock_ratio -> hdmi_high_tmds_clock_ratio V5: Addressed review comments from Ville and Ander - Do not modifiy the crtc_state after compute_config. Move all scrambling and tmds_clock_ratio calcutations to compute_config. - While setting scrambling for source/sink, do not check the conditions again, just go by the crtc_state flags. This will simplyfy the condition checks. V6: Addressed review comments from Ville - Do not add IS_GLK check in disable/enable function, instead add it in compute_config, while setting state flags. - Remove unnecessary paranthesis. - Simplyfy handle_sink_scrambling function as suggested. - Add readout code for scrambling status in get_ddi_config and add a check for the same in pipe_config_compare. V7: Addressed review comments from Ander/Ville - No separate function for source scrambling, make it inline - Align the last line of the macro TRANS_DDI_HDMI_SCRAMBLING_MASK - Do not add platform check while setting source scrambling - Use pipe_config instead of crtc->config to set sink scrambling - To readout scrambling status, Compare with SCRAMBLING_MASK not any of its bits - Remove platform check in intel_pipe_config_compare while checking scrambling status V8: Fixed mege conflict, Addressed review comments from Ander - Remove the desciption/comment about scrambling fom the caller, move it to the function - Move the IS_GLK check into scrambling function - Fix alignment V9: Fixed review comments from Ville, Ander - Pass the scrambling state variables as bool input to the sink_scrambling function and let the disable call be unconditional. - Fix alignments in function calls and debug messages. - Add kernel doc for function intel_hdmi_handle_sink_scrambling V10: Rebase Signed-off-by: Shashank Sharma <shashank.sharma@intel.com> Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1489404244-16608-6-git-send-email-shashank.sharma@intel.com
2017-03-13 11:24:03 +00:00
if ((temp & TRANS_DDI_HDMI_SCRAMBLING_MASK) ==
TRANS_DDI_HDMI_SCRAMBLING_MASK)
pipe_config->hdmi_scrambling = true;
if (temp & TRANS_DDI_HIGH_TMDS_CHAR_RATE)
pipe_config->hdmi_high_tmds_clock_ratio = true;
/* fall through */
case TRANS_DDI_MODE_SELECT_DVI:
pipe_config->lane_count = 4;
break;
case TRANS_DDI_MODE_SELECT_FDI:
break;
case TRANS_DDI_MODE_SELECT_DP_SST:
case TRANS_DDI_MODE_SELECT_DP_MST:
pipe_config->lane_count =
((temp & DDI_PORT_WIDTH_MASK) >> DDI_PORT_WIDTH_SHIFT) + 1;
intel_dp_get_m_n(intel_crtc, pipe_config);
break;
default:
break;
}
pipe_config->has_audio =
intel_ddi_is_audio_enabled(dev_priv, intel_crtc);
if (encoder->type == INTEL_OUTPUT_EDP && dev_priv->vbt.edp.bpp &&
pipe_config->pipe_bpp > dev_priv->vbt.edp.bpp) {
/*
* This is a big fat ugly hack.
*
* Some machines in UEFI boot mode provide us a VBT that has 18
* bpp and 1.62 GHz link bandwidth for eDP, which for reasons
* unknown we fail to light up. Yet the same BIOS boots up with
* 24 bpp and 2.7 GHz link. Use the same bpp as the BIOS uses as
* max, not what it tells us to use.
*
* Note: This will still be broken if the eDP panel is not lit
* up by the BIOS, and thus we can't get the mode at module
* load.
*/
DRM_DEBUG_KMS("pipe has %d bpp for eDP panel, overriding BIOS-provided max %d bpp\n",
pipe_config->pipe_bpp, dev_priv->vbt.edp.bpp);
dev_priv->vbt.edp.bpp = pipe_config->pipe_bpp;
}
intel_ddi_clock_get(encoder, pipe_config);
if (IS_GEN9_LP(dev_priv))
pipe_config->lane_lat_optim_mask =
bxt_ddi_phy_get_lane_lat_optim_mask(encoder);
}
static bool intel_ddi_compute_config(struct intel_encoder *encoder,
struct intel_crtc_state *pipe_config,
struct drm_connector_state *conn_state)
{
struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
int type = encoder->type;
int port = intel_ddi_get_encoder_port(encoder);
int ret;
WARN(type == INTEL_OUTPUT_UNKNOWN, "compute_config() on unknown output!\n");
if (port == PORT_A)
pipe_config->cpu_transcoder = TRANSCODER_EDP;
if (type == INTEL_OUTPUT_HDMI)
ret = intel_hdmi_compute_config(encoder, pipe_config, conn_state);
else
ret = intel_dp_compute_config(encoder, pipe_config, conn_state);
if (IS_GEN9_LP(dev_priv) && ret)
pipe_config->lane_lat_optim_mask =
bxt_ddi_phy_calc_lane_lat_optim_mask(encoder,
pipe_config->lane_count);
return ret;
}
static const struct drm_encoder_funcs intel_ddi_funcs = {
.reset = intel_dp_encoder_reset,
.destroy = intel_dp_encoder_destroy,
};
static struct intel_connector *
intel_ddi_init_dp_connector(struct intel_digital_port *intel_dig_port)
{
struct intel_connector *connector;
enum port port = intel_dig_port->port;
connector = intel_connector_alloc();
if (!connector)
return NULL;
intel_dig_port->dp.output_reg = DDI_BUF_CTL(port);
if (!intel_dp_init_connector(intel_dig_port, connector)) {
kfree(connector);
return NULL;
}
return connector;
}
static struct intel_connector *
intel_ddi_init_hdmi_connector(struct intel_digital_port *intel_dig_port)
{
struct intel_connector *connector;
enum port port = intel_dig_port->port;
connector = intel_connector_alloc();
if (!connector)
return NULL;
intel_dig_port->hdmi.hdmi_reg = DDI_BUF_CTL(port);
intel_hdmi_init_connector(intel_dig_port, connector);
return connector;
}
void intel_ddi_init(struct drm_i915_private *dev_priv, enum port port)
{
struct intel_digital_port *intel_dig_port;
struct intel_encoder *intel_encoder;
struct drm_encoder *encoder;
bool init_hdmi, init_dp, init_lspcon = false;
int max_lanes;
if (I915_READ(DDI_BUF_CTL(PORT_A)) & DDI_A_4_LANES) {
switch (port) {
case PORT_A:
max_lanes = 4;
break;
case PORT_E:
max_lanes = 0;
break;
default:
max_lanes = 4;
break;
}
} else {
switch (port) {
case PORT_A:
max_lanes = 2;
break;
case PORT_E:
max_lanes = 2;
break;
default:
max_lanes = 4;
break;
}
}
init_hdmi = (dev_priv->vbt.ddi_port_info[port].supports_dvi ||
dev_priv->vbt.ddi_port_info[port].supports_hdmi);
init_dp = dev_priv->vbt.ddi_port_info[port].supports_dp;
if (intel_bios_is_lspcon_present(dev_priv, port)) {
/*
* Lspcon device needs to be driven with DP connector
* with special detection sequence. So make sure DP
* is initialized before lspcon.
*/
init_dp = true;
init_lspcon = true;
init_hdmi = false;
DRM_DEBUG_KMS("VBT says port %c has lspcon\n", port_name(port));
}
if (!init_dp && !init_hdmi) {
DRM_DEBUG_KMS("VBT says port %c is not DVI/HDMI/DP compatible, respect it\n",
port_name(port));
return;
}
intel_dig_port = kzalloc(sizeof(*intel_dig_port), GFP_KERNEL);
if (!intel_dig_port)
return;
intel_encoder = &intel_dig_port->base;
encoder = &intel_encoder->base;
drm_encoder_init(&dev_priv->drm, encoder, &intel_ddi_funcs,
DRM_MODE_ENCODER_TMDS, "DDI %c", port_name(port));
intel_encoder->compute_config = intel_ddi_compute_config;
intel_encoder->enable = intel_enable_ddi;
if (IS_GEN9_LP(dev_priv))
intel_encoder->pre_pll_enable = bxt_ddi_pre_pll_enable;
intel_encoder->pre_enable = intel_ddi_pre_enable;
intel_encoder->disable = intel_disable_ddi;
intel_encoder->post_disable = intel_ddi_post_disable;
intel_encoder->get_hw_state = intel_ddi_get_hw_state;
intel_encoder->get_config = intel_ddi_get_config;
intel_encoder->suspend = intel_dp_encoder_suspend;
intel_encoder->get_power_domains = intel_ddi_get_power_domains;
intel_dig_port->port = port;
intel_dig_port->saved_port_bits = I915_READ(DDI_BUF_CTL(port)) &
(DDI_BUF_PORT_REVERSAL |
DDI_A_4_LANES);
switch (port) {
case PORT_A:
intel_dig_port->ddi_io_power_domain =
POWER_DOMAIN_PORT_DDI_A_IO;
break;
case PORT_B:
intel_dig_port->ddi_io_power_domain =
POWER_DOMAIN_PORT_DDI_B_IO;
break;
case PORT_C:
intel_dig_port->ddi_io_power_domain =
POWER_DOMAIN_PORT_DDI_C_IO;
break;
case PORT_D:
intel_dig_port->ddi_io_power_domain =
POWER_DOMAIN_PORT_DDI_D_IO;
break;
case PORT_E:
intel_dig_port->ddi_io_power_domain =
POWER_DOMAIN_PORT_DDI_E_IO;
break;
default:
MISSING_CASE(port);
}
/*
* Bspec says that DDI_A_4_LANES is the only supported configuration
* for Broxton. Yet some BIOS fail to set this bit on port A if eDP
* wasn't lit up at boot. Force this bit on in our internal
* configuration so that we use the proper lane count for our
* calculations.
*/
if (IS_GEN9_LP(dev_priv) && port == PORT_A) {
if (!(intel_dig_port->saved_port_bits & DDI_A_4_LANES)) {
DRM_DEBUG_KMS("BXT BIOS forgot to set DDI_A_4_LANES for port A; fixing\n");
intel_dig_port->saved_port_bits |= DDI_A_4_LANES;
max_lanes = 4;
}
}
intel_dig_port->max_lanes = max_lanes;
intel_encoder->type = INTEL_OUTPUT_UNKNOWN;
intel_encoder->power_domain = intel_port_to_power_domain(port);
intel_encoder->port = port;
intel_encoder->crtc_mask = (1 << 0) | (1 << 1) | (1 << 2);
intel_encoder->cloneable = 0;
if (init_dp) {
if (!intel_ddi_init_dp_connector(intel_dig_port))
goto err;
intel_dig_port->hpd_pulse = intel_dp_hpd_pulse;
dev_priv->hotplug.irq_port[port] = intel_dig_port;
}
/* In theory we don't need the encoder->type check, but leave it just in
* case we have some really bad VBTs... */
if (intel_encoder->type != INTEL_OUTPUT_EDP && init_hdmi) {
if (!intel_ddi_init_hdmi_connector(intel_dig_port))
goto err;
}
if (init_lspcon) {
if (lspcon_init(intel_dig_port))
/* TODO: handle hdmi info frame part */
DRM_DEBUG_KMS("LSPCON init success on port %c\n",
port_name(port));
else
/*
* LSPCON init faied, but DP init was success, so
* lets try to drive as DP++ port.
*/
DRM_ERROR("LSPCON init failed on port %c\n",
port_name(port));
}
return;
err:
drm_encoder_cleanup(encoder);
kfree(intel_dig_port);
}