linux/drivers/iio/light/tsl2772.c

1948 lines
48 KiB
C
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0+
/*
* Device driver for monitoring ambient light intensity in (lux) and proximity
* detection (prox) within the TAOS TSL2571, TSL2671, TMD2671, TSL2771, TMD2771,
* TSL2572, TSL2672, TMD2672, TSL2772, and TMD2772 devices.
*
* Copyright (c) 2012, TAOS Corporation.
* Copyright (c) 2017-2018 Brian Masney <masneyb@onstation.org>
*/
#include <linux/delay.h>
#include <linux/errno.h>
#include <linux/i2c.h>
#include <linux/interrupt.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/mutex.h>
#include <linux/slab.h>
#include <linux/iio/events.h>
#include <linux/iio/iio.h>
#include <linux/iio/sysfs.h>
#include <linux/platform_data/tsl2772.h>
#include <linux/regulator/consumer.h>
/* Cal defs */
#define PROX_STAT_CAL 0
#define PROX_STAT_SAMP 1
#define MAX_SAMPLES_CAL 200
/* TSL2772 Device ID */
#define TRITON_ID 0x00
#define SWORDFISH_ID 0x30
#define HALIBUT_ID 0x20
/* Lux calculation constants */
#define TSL2772_LUX_CALC_OVER_FLOW 65535
/*
* TAOS Register definitions - Note: depending on device, some of these register
* are not used and the register address is benign.
*/
/* Register offsets */
#define TSL2772_MAX_CONFIG_REG 16
/* Device Registers and Masks */
#define TSL2772_CNTRL 0x00
#define TSL2772_ALS_TIME 0X01
#define TSL2772_PRX_TIME 0x02
#define TSL2772_WAIT_TIME 0x03
#define TSL2772_ALS_MINTHRESHLO 0X04
#define TSL2772_ALS_MINTHRESHHI 0X05
#define TSL2772_ALS_MAXTHRESHLO 0X06
#define TSL2772_ALS_MAXTHRESHHI 0X07
#define TSL2772_PRX_MINTHRESHLO 0X08
#define TSL2772_PRX_MINTHRESHHI 0X09
#define TSL2772_PRX_MAXTHRESHLO 0X0A
#define TSL2772_PRX_MAXTHRESHHI 0X0B
#define TSL2772_PERSISTENCE 0x0C
#define TSL2772_ALS_PRX_CONFIG 0x0D
#define TSL2772_PRX_COUNT 0x0E
#define TSL2772_GAIN 0x0F
#define TSL2772_NOTUSED 0x10
#define TSL2772_REVID 0x11
#define TSL2772_CHIPID 0x12
#define TSL2772_STATUS 0x13
#define TSL2772_ALS_CHAN0LO 0x14
#define TSL2772_ALS_CHAN0HI 0x15
#define TSL2772_ALS_CHAN1LO 0x16
#define TSL2772_ALS_CHAN1HI 0x17
#define TSL2772_PRX_LO 0x18
#define TSL2772_PRX_HI 0x19
/* tsl2772 cmd reg masks */
#define TSL2772_CMD_REG 0x80
#define TSL2772_CMD_SPL_FN 0x60
#define TSL2772_CMD_REPEAT_PROTO 0x00
#define TSL2772_CMD_AUTOINC_PROTO 0x20
#define TSL2772_CMD_PROX_INT_CLR 0X05
#define TSL2772_CMD_ALS_INT_CLR 0x06
#define TSL2772_CMD_PROXALS_INT_CLR 0X07
/* tsl2772 cntrl reg masks */
#define TSL2772_CNTL_ADC_ENBL 0x02
#define TSL2772_CNTL_PWR_ON 0x01
/* tsl2772 status reg masks */
#define TSL2772_STA_ADC_VALID 0x01
#define TSL2772_STA_PRX_VALID 0x02
#define TSL2772_STA_ADC_PRX_VALID (TSL2772_STA_ADC_VALID | \
TSL2772_STA_PRX_VALID)
#define TSL2772_STA_ALS_INTR 0x10
#define TSL2772_STA_PRX_INTR 0x20
/* tsl2772 cntrl reg masks */
#define TSL2772_CNTL_REG_CLEAR 0x00
#define TSL2772_CNTL_PROX_INT_ENBL 0X20
#define TSL2772_CNTL_ALS_INT_ENBL 0X10
#define TSL2772_CNTL_WAIT_TMR_ENBL 0X08
#define TSL2772_CNTL_PROX_DET_ENBL 0X04
#define TSL2772_CNTL_PWRON 0x01
#define TSL2772_CNTL_ALSPON_ENBL 0x03
#define TSL2772_CNTL_INTALSPON_ENBL 0x13
#define TSL2772_CNTL_PROXPON_ENBL 0x0F
#define TSL2772_CNTL_INTPROXPON_ENBL 0x2F
#define TSL2772_ALS_GAIN_TRIM_MIN 250
#define TSL2772_ALS_GAIN_TRIM_MAX 4000
#define TSL2772_MAX_PROX_LEDS 2
#define TSL2772_BOOT_MIN_SLEEP_TIME 10000
#define TSL2772_BOOT_MAX_SLEEP_TIME 28000
/* Device family members */
enum {
tsl2571,
tsl2671,
tmd2671,
tsl2771,
tmd2771,
tsl2572,
tsl2672,
tmd2672,
tsl2772,
tmd2772,
apds9930,
};
enum {
TSL2772_CHIP_UNKNOWN = 0,
TSL2772_CHIP_WORKING = 1,
TSL2772_CHIP_SUSPENDED = 2
};
enum {
TSL2772_SUPPLY_VDD = 0,
TSL2772_SUPPLY_VDDIO = 1,
TSL2772_NUM_SUPPLIES = 2
};
/* Per-device data */
struct tsl2772_als_info {
u16 als_ch0;
u16 als_ch1;
u16 lux;
};
struct tsl2772_chip_info {
int chan_table_elements;
struct iio_chan_spec channel_with_events[4];
struct iio_chan_spec channel_without_events[4];
const struct iio_info *info;
};
static const int tsl2772_led_currents[][2] = {
{ 100000, TSL2772_100_mA },
{ 50000, TSL2772_50_mA },
{ 25000, TSL2772_25_mA },
{ 13000, TSL2772_13_mA },
{ 0, 0 }
};
struct tsl2772_chip {
kernel_ulong_t id;
struct mutex prox_mutex;
struct mutex als_mutex;
struct i2c_client *client;
struct regulator_bulk_data supplies[TSL2772_NUM_SUPPLIES];
u16 prox_data;
struct tsl2772_als_info als_cur_info;
struct tsl2772_settings settings;
struct tsl2772_platform_data *pdata;
staging: iio: tsl2x7x: correct integration time and lux equation The integration_time sysfs attribute did not report the correct time. Changing the integration time would cause the reported lux to change wildly. Once the integration time was corrected, all of the equations, and lux tables needed to be corrected to match what the data sheets expected. This patch corrects all of this, and adds some more comments about how some of the constants were derived. Here are the results from testing a TSL2772 hooked up to a Raspberry Pi 2: # cat in_intensity0_integration_time 0.002730 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 # echo 0.65 > in_intensity0_integration_time # cat in_intensity0_integration_time 0.649740 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 with noticeable lag to lux changes in watch ; process. ; Now test the ALS calibration routine. # cat in_intensity0_calibbias 1000 # cat in_illuminance0_target_input 150 # echo 1 > in_illuminance0_calibrate # cat in_intensity0_calibbias 2777 # watch -n .1 cat in_illuminance0_input ; Lux now hovers around 150-155 The returned lux values were tested on a TSL2772 in various lighting conditions and the results are within the lux ranges described at https://en.wikipedia.org/wiki/Lux. The driver was primarily tested using a TSL2772, however some quick tests were also ran against the devices TSL2771, TSL2572, and TMD2772. Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-04 02:53:14 +00:00
int als_gain_time_scale;
int als_saturation;
int tsl2772_chip_status;
u8 tsl2772_config[TSL2772_MAX_CONFIG_REG];
const struct tsl2772_chip_info *chip_info;
const struct iio_info *info;
s64 event_timestamp;
/*
* This structure is intentionally large to accommodate
* updates via sysfs.
* Sized to 9 = max 8 segments + 1 termination segment
*/
struct tsl2772_lux tsl2772_device_lux[TSL2772_MAX_LUX_TABLE_SIZE];
};
staging: iio: tsl2x7x: correct integration time and lux equation The integration_time sysfs attribute did not report the correct time. Changing the integration time would cause the reported lux to change wildly. Once the integration time was corrected, all of the equations, and lux tables needed to be corrected to match what the data sheets expected. This patch corrects all of this, and adds some more comments about how some of the constants were derived. Here are the results from testing a TSL2772 hooked up to a Raspberry Pi 2: # cat in_intensity0_integration_time 0.002730 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 # echo 0.65 > in_intensity0_integration_time # cat in_intensity0_integration_time 0.649740 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 with noticeable lag to lux changes in watch ; process. ; Now test the ALS calibration routine. # cat in_intensity0_calibbias 1000 # cat in_illuminance0_target_input 150 # echo 1 > in_illuminance0_calibrate # cat in_intensity0_calibbias 2777 # watch -n .1 cat in_illuminance0_input ; Lux now hovers around 150-155 The returned lux values were tested on a TSL2772 in various lighting conditions and the results are within the lux ranges described at https://en.wikipedia.org/wiki/Lux. The driver was primarily tested using a TSL2772, however some quick tests were also ran against the devices TSL2771, TSL2572, and TMD2772. Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-04 02:53:14 +00:00
/*
* Different devices require different coefficents, and these numbers were
* derived from the 'Lux Equation' section of the various device datasheets.
* All of these coefficients assume a Glass Attenuation (GA) factor of 1.
* The coefficients are multiplied by 1000 to avoid floating point operations.
* The two rows in each table correspond to the Lux1 and Lux2 equations from
* the datasheets.
*/
static const struct tsl2772_lux tsl2x71_lux_table[TSL2772_DEF_LUX_TABLE_SZ] = {
staging: iio: tsl2x7x: correct integration time and lux equation The integration_time sysfs attribute did not report the correct time. Changing the integration time would cause the reported lux to change wildly. Once the integration time was corrected, all of the equations, and lux tables needed to be corrected to match what the data sheets expected. This patch corrects all of this, and adds some more comments about how some of the constants were derived. Here are the results from testing a TSL2772 hooked up to a Raspberry Pi 2: # cat in_intensity0_integration_time 0.002730 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 # echo 0.65 > in_intensity0_integration_time # cat in_intensity0_integration_time 0.649740 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 with noticeable lag to lux changes in watch ; process. ; Now test the ALS calibration routine. # cat in_intensity0_calibbias 1000 # cat in_illuminance0_target_input 150 # echo 1 > in_illuminance0_calibrate # cat in_intensity0_calibbias 2777 # watch -n .1 cat in_illuminance0_input ; Lux now hovers around 150-155 The returned lux values were tested on a TSL2772 in various lighting conditions and the results are within the lux ranges described at https://en.wikipedia.org/wiki/Lux. The driver was primarily tested using a TSL2772, however some quick tests were also ran against the devices TSL2771, TSL2572, and TMD2772. Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-04 02:53:14 +00:00
{ 53000, 106000 },
{ 31800, 53000 },
{ 0, 0 },
};
static const struct tsl2772_lux tmd2x71_lux_table[TSL2772_DEF_LUX_TABLE_SZ] = {
staging: iio: tsl2x7x: correct integration time and lux equation The integration_time sysfs attribute did not report the correct time. Changing the integration time would cause the reported lux to change wildly. Once the integration time was corrected, all of the equations, and lux tables needed to be corrected to match what the data sheets expected. This patch corrects all of this, and adds some more comments about how some of the constants were derived. Here are the results from testing a TSL2772 hooked up to a Raspberry Pi 2: # cat in_intensity0_integration_time 0.002730 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 # echo 0.65 > in_intensity0_integration_time # cat in_intensity0_integration_time 0.649740 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 with noticeable lag to lux changes in watch ; process. ; Now test the ALS calibration routine. # cat in_intensity0_calibbias 1000 # cat in_illuminance0_target_input 150 # echo 1 > in_illuminance0_calibrate # cat in_intensity0_calibbias 2777 # watch -n .1 cat in_illuminance0_input ; Lux now hovers around 150-155 The returned lux values were tested on a TSL2772 in various lighting conditions and the results are within the lux ranges described at https://en.wikipedia.org/wiki/Lux. The driver was primarily tested using a TSL2772, however some quick tests were also ran against the devices TSL2771, TSL2572, and TMD2772. Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-04 02:53:14 +00:00
{ 24000, 48000 },
{ 14400, 24000 },
{ 0, 0 },
};
static const struct tsl2772_lux tsl2x72_lux_table[TSL2772_DEF_LUX_TABLE_SZ] = {
staging: iio: tsl2x7x: correct integration time and lux equation The integration_time sysfs attribute did not report the correct time. Changing the integration time would cause the reported lux to change wildly. Once the integration time was corrected, all of the equations, and lux tables needed to be corrected to match what the data sheets expected. This patch corrects all of this, and adds some more comments about how some of the constants were derived. Here are the results from testing a TSL2772 hooked up to a Raspberry Pi 2: # cat in_intensity0_integration_time 0.002730 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 # echo 0.65 > in_intensity0_integration_time # cat in_intensity0_integration_time 0.649740 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 with noticeable lag to lux changes in watch ; process. ; Now test the ALS calibration routine. # cat in_intensity0_calibbias 1000 # cat in_illuminance0_target_input 150 # echo 1 > in_illuminance0_calibrate # cat in_intensity0_calibbias 2777 # watch -n .1 cat in_illuminance0_input ; Lux now hovers around 150-155 The returned lux values were tested on a TSL2772 in various lighting conditions and the results are within the lux ranges described at https://en.wikipedia.org/wiki/Lux. The driver was primarily tested using a TSL2772, however some quick tests were also ran against the devices TSL2771, TSL2572, and TMD2772. Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-04 02:53:14 +00:00
{ 60000, 112200 },
{ 37800, 60000 },
{ 0, 0 },
};
static const struct tsl2772_lux tmd2x72_lux_table[TSL2772_DEF_LUX_TABLE_SZ] = {
staging: iio: tsl2x7x: correct integration time and lux equation The integration_time sysfs attribute did not report the correct time. Changing the integration time would cause the reported lux to change wildly. Once the integration time was corrected, all of the equations, and lux tables needed to be corrected to match what the data sheets expected. This patch corrects all of this, and adds some more comments about how some of the constants were derived. Here are the results from testing a TSL2772 hooked up to a Raspberry Pi 2: # cat in_intensity0_integration_time 0.002730 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 # echo 0.65 > in_intensity0_integration_time # cat in_intensity0_integration_time 0.649740 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 with noticeable lag to lux changes in watch ; process. ; Now test the ALS calibration routine. # cat in_intensity0_calibbias 1000 # cat in_illuminance0_target_input 150 # echo 1 > in_illuminance0_calibrate # cat in_intensity0_calibbias 2777 # watch -n .1 cat in_illuminance0_input ; Lux now hovers around 150-155 The returned lux values were tested on a TSL2772 in various lighting conditions and the results are within the lux ranges described at https://en.wikipedia.org/wiki/Lux. The driver was primarily tested using a TSL2772, however some quick tests were also ran against the devices TSL2771, TSL2572, and TMD2772. Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-04 02:53:14 +00:00
{ 20000, 35000 },
{ 12600, 20000 },
{ 0, 0 },
};
static const struct tsl2772_lux apds9930_lux_table[TSL2772_DEF_LUX_TABLE_SZ] = {
{ 52000, 96824 },
{ 38792, 67132 },
{ 0, 0 },
};
static const struct tsl2772_lux *tsl2772_default_lux_table_group[] = {
[tsl2571] = tsl2x71_lux_table,
[tsl2671] = tsl2x71_lux_table,
[tmd2671] = tmd2x71_lux_table,
[tsl2771] = tsl2x71_lux_table,
[tmd2771] = tmd2x71_lux_table,
[tsl2572] = tsl2x72_lux_table,
[tsl2672] = tsl2x72_lux_table,
[tmd2672] = tmd2x72_lux_table,
[tsl2772] = tsl2x72_lux_table,
[tmd2772] = tmd2x72_lux_table,
[apds9930] = apds9930_lux_table,
};
static const struct tsl2772_settings tsl2772_default_settings = {
.als_time = 255, /* 2.72 / 2.73 ms */
.als_gain = 0,
.prox_time = 255, /* 2.72 / 2.73 ms */
.prox_gain = 0,
.wait_time = 255,
.als_prox_config = 0,
.als_gain_trim = 1000,
.als_cal_target = 150,
.als_persistence = 1,
.als_interrupt_en = false,
.als_thresh_low = 200,
.als_thresh_high = 256,
.prox_persistence = 1,
.prox_interrupt_en = false,
.prox_thres_low = 0,
.prox_thres_high = 512,
.prox_max_samples_cal = 30,
.prox_pulse_count = 8,
.prox_diode = TSL2772_DIODE1,
.prox_power = TSL2772_100_mA
};
static const s16 tsl2772_als_gain[] = {
1,
8,
16,
120
};
static const s16 tsl2772_prox_gain[] = {
1,
2,
4,
8
};
static const int tsl2772_int_time_avail[][6] = {
[tsl2571] = { 0, 2720, 0, 2720, 0, 696000 },
[tsl2671] = { 0, 2720, 0, 2720, 0, 696000 },
[tmd2671] = { 0, 2720, 0, 2720, 0, 696000 },
[tsl2771] = { 0, 2720, 0, 2720, 0, 696000 },
[tmd2771] = { 0, 2720, 0, 2720, 0, 696000 },
[tsl2572] = { 0, 2730, 0, 2730, 0, 699000 },
[tsl2672] = { 0, 2730, 0, 2730, 0, 699000 },
[tmd2672] = { 0, 2730, 0, 2730, 0, 699000 },
[tsl2772] = { 0, 2730, 0, 2730, 0, 699000 },
[tmd2772] = { 0, 2730, 0, 2730, 0, 699000 },
[apds9930] = { 0, 2730, 0, 2730, 0, 699000 },
};
static int tsl2772_int_calibscale_avail[] = { 1, 8, 16, 120 };
static int tsl2772_prox_calibscale_avail[] = { 1, 2, 4, 8 };
/* Channel variations */
enum {
ALS,
PRX,
ALSPRX,
PRX2,
ALSPRX2,
};
static const u8 device_channel_config[] = {
[tsl2571] = ALS,
[tsl2671] = PRX,
[tmd2671] = PRX,
[tsl2771] = ALSPRX,
[tmd2771] = ALSPRX,
[tsl2572] = ALS,
[tsl2672] = PRX2,
[tmd2672] = PRX2,
[tsl2772] = ALSPRX2,
[tmd2772] = ALSPRX2,
[apds9930] = ALSPRX2,
};
static int tsl2772_read_status(struct tsl2772_chip *chip)
{
int ret;
ret = i2c_smbus_read_byte_data(chip->client,
TSL2772_CMD_REG | TSL2772_STATUS);
if (ret < 0)
dev_err(&chip->client->dev,
"%s: failed to read STATUS register: %d\n", __func__,
ret);
return ret;
}
static int tsl2772_write_control_reg(struct tsl2772_chip *chip, u8 data)
{
int ret;
ret = i2c_smbus_write_byte_data(chip->client,
TSL2772_CMD_REG | TSL2772_CNTRL, data);
if (ret < 0) {
dev_err(&chip->client->dev,
"%s: failed to write to control register %x: %d\n",
__func__, data, ret);
}
return ret;
}
static int tsl2772_read_autoinc_regs(struct tsl2772_chip *chip, int lower_reg,
int upper_reg)
{
u8 buf[2];
int ret;
ret = i2c_smbus_write_byte(chip->client,
TSL2772_CMD_REG | TSL2772_CMD_AUTOINC_PROTO |
lower_reg);
if (ret < 0) {
dev_err(&chip->client->dev,
"%s: failed to enable auto increment protocol: %d\n",
__func__, ret);
return ret;
}
ret = i2c_smbus_read_byte_data(chip->client,
TSL2772_CMD_REG | lower_reg);
if (ret < 0) {
dev_err(&chip->client->dev,
"%s: failed to read from register %x: %d\n", __func__,
lower_reg, ret);
return ret;
}
buf[0] = ret;
ret = i2c_smbus_read_byte_data(chip->client,
TSL2772_CMD_REG | upper_reg);
if (ret < 0) {
dev_err(&chip->client->dev,
"%s: failed to read from register %x: %d\n", __func__,
upper_reg, ret);
return ret;
}
buf[1] = ret;
ret = i2c_smbus_write_byte(chip->client,
TSL2772_CMD_REG | TSL2772_CMD_REPEAT_PROTO |
lower_reg);
if (ret < 0) {
dev_err(&chip->client->dev,
"%s: failed to enable repeated byte protocol: %d\n",
__func__, ret);
return ret;
}
return le16_to_cpup((const __le16 *)&buf[0]);
}
/**
* tsl2772_get_lux() - Reads and calculates current lux value.
* @indio_dev: pointer to IIO device
*
* The raw ch0 and ch1 values of the ambient light sensed in the last
staging: iio: tsl2x7x: correct integration time and lux equation The integration_time sysfs attribute did not report the correct time. Changing the integration time would cause the reported lux to change wildly. Once the integration time was corrected, all of the equations, and lux tables needed to be corrected to match what the data sheets expected. This patch corrects all of this, and adds some more comments about how some of the constants were derived. Here are the results from testing a TSL2772 hooked up to a Raspberry Pi 2: # cat in_intensity0_integration_time 0.002730 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 # echo 0.65 > in_intensity0_integration_time # cat in_intensity0_integration_time 0.649740 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 with noticeable lag to lux changes in watch ; process. ; Now test the ALS calibration routine. # cat in_intensity0_calibbias 1000 # cat in_illuminance0_target_input 150 # echo 1 > in_illuminance0_calibrate # cat in_intensity0_calibbias 2777 # watch -n .1 cat in_illuminance0_input ; Lux now hovers around 150-155 The returned lux values were tested on a TSL2772 in various lighting conditions and the results are within the lux ranges described at https://en.wikipedia.org/wiki/Lux. The driver was primarily tested using a TSL2772, however some quick tests were also ran against the devices TSL2771, TSL2572, and TMD2772. Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-04 02:53:14 +00:00
* integration cycle are read from the device. The raw values are multiplied
* by a device-specific scale factor, and divided by the integration time and
* device gain. The code supports multiple lux equations through the lux table
* coefficients. A lux gain trim is applied to each lux equation, and then the
* maximum lux within the interval 0..65535 is selected.
*/
static int tsl2772_get_lux(struct iio_dev *indio_dev)
{
struct tsl2772_chip *chip = iio_priv(indio_dev);
struct tsl2772_lux *p;
staging: iio: tsl2x7x: correct integration time and lux equation The integration_time sysfs attribute did not report the correct time. Changing the integration time would cause the reported lux to change wildly. Once the integration time was corrected, all of the equations, and lux tables needed to be corrected to match what the data sheets expected. This patch corrects all of this, and adds some more comments about how some of the constants were derived. Here are the results from testing a TSL2772 hooked up to a Raspberry Pi 2: # cat in_intensity0_integration_time 0.002730 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 # echo 0.65 > in_intensity0_integration_time # cat in_intensity0_integration_time 0.649740 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 with noticeable lag to lux changes in watch ; process. ; Now test the ALS calibration routine. # cat in_intensity0_calibbias 1000 # cat in_illuminance0_target_input 150 # echo 1 > in_illuminance0_calibrate # cat in_intensity0_calibbias 2777 # watch -n .1 cat in_illuminance0_input ; Lux now hovers around 150-155 The returned lux values were tested on a TSL2772 in various lighting conditions and the results are within the lux ranges described at https://en.wikipedia.org/wiki/Lux. The driver was primarily tested using a TSL2772, however some quick tests were also ran against the devices TSL2771, TSL2572, and TMD2772. Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-04 02:53:14 +00:00
int max_lux, ret;
bool overflow;
mutex_lock(&chip->als_mutex);
if (chip->tsl2772_chip_status != TSL2772_CHIP_WORKING) {
dev_err(&chip->client->dev, "%s: device is not enabled\n",
__func__);
ret = -EBUSY;
goto out_unlock;
}
ret = tsl2772_read_status(chip);
if (ret < 0)
goto out_unlock;
if (!(ret & TSL2772_STA_ADC_VALID)) {
dev_err(&chip->client->dev,
"%s: data not valid yet\n", __func__);
ret = chip->als_cur_info.lux; /* return LAST VALUE */
goto out_unlock;
}
ret = tsl2772_read_autoinc_regs(chip, TSL2772_ALS_CHAN0LO,
TSL2772_ALS_CHAN0HI);
if (ret < 0)
goto out_unlock;
chip->als_cur_info.als_ch0 = ret;
ret = tsl2772_read_autoinc_regs(chip, TSL2772_ALS_CHAN1LO,
TSL2772_ALS_CHAN1HI);
if (ret < 0)
goto out_unlock;
chip->als_cur_info.als_ch1 = ret;
staging: iio: tsl2x7x: correct integration time and lux equation The integration_time sysfs attribute did not report the correct time. Changing the integration time would cause the reported lux to change wildly. Once the integration time was corrected, all of the equations, and lux tables needed to be corrected to match what the data sheets expected. This patch corrects all of this, and adds some more comments about how some of the constants were derived. Here are the results from testing a TSL2772 hooked up to a Raspberry Pi 2: # cat in_intensity0_integration_time 0.002730 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 # echo 0.65 > in_intensity0_integration_time # cat in_intensity0_integration_time 0.649740 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 with noticeable lag to lux changes in watch ; process. ; Now test the ALS calibration routine. # cat in_intensity0_calibbias 1000 # cat in_illuminance0_target_input 150 # echo 1 > in_illuminance0_calibrate # cat in_intensity0_calibbias 2777 # watch -n .1 cat in_illuminance0_input ; Lux now hovers around 150-155 The returned lux values were tested on a TSL2772 in various lighting conditions and the results are within the lux ranges described at https://en.wikipedia.org/wiki/Lux. The driver was primarily tested using a TSL2772, however some quick tests were also ran against the devices TSL2771, TSL2572, and TMD2772. Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-04 02:53:14 +00:00
if (chip->als_cur_info.als_ch0 >= chip->als_saturation) {
max_lux = TSL2772_LUX_CALC_OVER_FLOW;
staging: iio: tsl2x7x: correct integration time and lux equation The integration_time sysfs attribute did not report the correct time. Changing the integration time would cause the reported lux to change wildly. Once the integration time was corrected, all of the equations, and lux tables needed to be corrected to match what the data sheets expected. This patch corrects all of this, and adds some more comments about how some of the constants were derived. Here are the results from testing a TSL2772 hooked up to a Raspberry Pi 2: # cat in_intensity0_integration_time 0.002730 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 # echo 0.65 > in_intensity0_integration_time # cat in_intensity0_integration_time 0.649740 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 with noticeable lag to lux changes in watch ; process. ; Now test the ALS calibration routine. # cat in_intensity0_calibbias 1000 # cat in_illuminance0_target_input 150 # echo 1 > in_illuminance0_calibrate # cat in_intensity0_calibbias 2777 # watch -n .1 cat in_illuminance0_input ; Lux now hovers around 150-155 The returned lux values were tested on a TSL2772 in various lighting conditions and the results are within the lux ranges described at https://en.wikipedia.org/wiki/Lux. The driver was primarily tested using a TSL2772, however some quick tests were also ran against the devices TSL2771, TSL2572, and TMD2772. Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-04 02:53:14 +00:00
goto update_struct_with_max_lux;
}
if (!chip->als_cur_info.als_ch0) {
/* have no data, so return LAST VALUE */
ret = chip->als_cur_info.lux;
goto out_unlock;
}
staging: iio: tsl2x7x: correct integration time and lux equation The integration_time sysfs attribute did not report the correct time. Changing the integration time would cause the reported lux to change wildly. Once the integration time was corrected, all of the equations, and lux tables needed to be corrected to match what the data sheets expected. This patch corrects all of this, and adds some more comments about how some of the constants were derived. Here are the results from testing a TSL2772 hooked up to a Raspberry Pi 2: # cat in_intensity0_integration_time 0.002730 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 # echo 0.65 > in_intensity0_integration_time # cat in_intensity0_integration_time 0.649740 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 with noticeable lag to lux changes in watch ; process. ; Now test the ALS calibration routine. # cat in_intensity0_calibbias 1000 # cat in_illuminance0_target_input 150 # echo 1 > in_illuminance0_calibrate # cat in_intensity0_calibbias 2777 # watch -n .1 cat in_illuminance0_input ; Lux now hovers around 150-155 The returned lux values were tested on a TSL2772 in various lighting conditions and the results are within the lux ranges described at https://en.wikipedia.org/wiki/Lux. The driver was primarily tested using a TSL2772, however some quick tests were also ran against the devices TSL2771, TSL2572, and TMD2772. Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-04 02:53:14 +00:00
max_lux = 0;
overflow = false;
for (p = (struct tsl2772_lux *)chip->tsl2772_device_lux; p->ch0 != 0;
staging: iio: tsl2x7x: correct integration time and lux equation The integration_time sysfs attribute did not report the correct time. Changing the integration time would cause the reported lux to change wildly. Once the integration time was corrected, all of the equations, and lux tables needed to be corrected to match what the data sheets expected. This patch corrects all of this, and adds some more comments about how some of the constants were derived. Here are the results from testing a TSL2772 hooked up to a Raspberry Pi 2: # cat in_intensity0_integration_time 0.002730 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 # echo 0.65 > in_intensity0_integration_time # cat in_intensity0_integration_time 0.649740 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 with noticeable lag to lux changes in watch ; process. ; Now test the ALS calibration routine. # cat in_intensity0_calibbias 1000 # cat in_illuminance0_target_input 150 # echo 1 > in_illuminance0_calibrate # cat in_intensity0_calibbias 2777 # watch -n .1 cat in_illuminance0_input ; Lux now hovers around 150-155 The returned lux values were tested on a TSL2772 in various lighting conditions and the results are within the lux ranges described at https://en.wikipedia.org/wiki/Lux. The driver was primarily tested using a TSL2772, however some quick tests were also ran against the devices TSL2771, TSL2572, and TMD2772. Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-04 02:53:14 +00:00
p++) {
int lux;
lux = ((chip->als_cur_info.als_ch0 * p->ch0) -
(chip->als_cur_info.als_ch1 * p->ch1)) /
chip->als_gain_time_scale;
/*
* The als_gain_trim can have a value within the range 250..4000
* and is a multiplier for the lux. A trim of 1000 makes no
* changes to the lux, less than 1000 scales it down, and
* greater than 1000 scales it up.
*/
lux = (lux * chip->settings.als_gain_trim) / 1000;
if (lux > TSL2772_LUX_CALC_OVER_FLOW) {
staging: iio: tsl2x7x: correct integration time and lux equation The integration_time sysfs attribute did not report the correct time. Changing the integration time would cause the reported lux to change wildly. Once the integration time was corrected, all of the equations, and lux tables needed to be corrected to match what the data sheets expected. This patch corrects all of this, and adds some more comments about how some of the constants were derived. Here are the results from testing a TSL2772 hooked up to a Raspberry Pi 2: # cat in_intensity0_integration_time 0.002730 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 # echo 0.65 > in_intensity0_integration_time # cat in_intensity0_integration_time 0.649740 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 with noticeable lag to lux changes in watch ; process. ; Now test the ALS calibration routine. # cat in_intensity0_calibbias 1000 # cat in_illuminance0_target_input 150 # echo 1 > in_illuminance0_calibrate # cat in_intensity0_calibbias 2777 # watch -n .1 cat in_illuminance0_input ; Lux now hovers around 150-155 The returned lux values were tested on a TSL2772 in various lighting conditions and the results are within the lux ranges described at https://en.wikipedia.org/wiki/Lux. The driver was primarily tested using a TSL2772, however some quick tests were also ran against the devices TSL2771, TSL2572, and TMD2772. Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-04 02:53:14 +00:00
overflow = true;
continue;
}
staging: iio: tsl2x7x: correct integration time and lux equation The integration_time sysfs attribute did not report the correct time. Changing the integration time would cause the reported lux to change wildly. Once the integration time was corrected, all of the equations, and lux tables needed to be corrected to match what the data sheets expected. This patch corrects all of this, and adds some more comments about how some of the constants were derived. Here are the results from testing a TSL2772 hooked up to a Raspberry Pi 2: # cat in_intensity0_integration_time 0.002730 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 # echo 0.65 > in_intensity0_integration_time # cat in_intensity0_integration_time 0.649740 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 with noticeable lag to lux changes in watch ; process. ; Now test the ALS calibration routine. # cat in_intensity0_calibbias 1000 # cat in_illuminance0_target_input 150 # echo 1 > in_illuminance0_calibrate # cat in_intensity0_calibbias 2777 # watch -n .1 cat in_illuminance0_input ; Lux now hovers around 150-155 The returned lux values were tested on a TSL2772 in various lighting conditions and the results are within the lux ranges described at https://en.wikipedia.org/wiki/Lux. The driver was primarily tested using a TSL2772, however some quick tests were also ran against the devices TSL2771, TSL2572, and TMD2772. Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-04 02:53:14 +00:00
max_lux = max(max_lux, lux);
}
staging: iio: tsl2x7x: correct integration time and lux equation The integration_time sysfs attribute did not report the correct time. Changing the integration time would cause the reported lux to change wildly. Once the integration time was corrected, all of the equations, and lux tables needed to be corrected to match what the data sheets expected. This patch corrects all of this, and adds some more comments about how some of the constants were derived. Here are the results from testing a TSL2772 hooked up to a Raspberry Pi 2: # cat in_intensity0_integration_time 0.002730 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 # echo 0.65 > in_intensity0_integration_time # cat in_intensity0_integration_time 0.649740 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 with noticeable lag to lux changes in watch ; process. ; Now test the ALS calibration routine. # cat in_intensity0_calibbias 1000 # cat in_illuminance0_target_input 150 # echo 1 > in_illuminance0_calibrate # cat in_intensity0_calibbias 2777 # watch -n .1 cat in_illuminance0_input ; Lux now hovers around 150-155 The returned lux values were tested on a TSL2772 in various lighting conditions and the results are within the lux ranges described at https://en.wikipedia.org/wiki/Lux. The driver was primarily tested using a TSL2772, however some quick tests were also ran against the devices TSL2771, TSL2572, and TMD2772. Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-04 02:53:14 +00:00
if (overflow && max_lux == 0)
max_lux = TSL2772_LUX_CALC_OVER_FLOW;
staging: iio: tsl2x7x: correct integration time and lux equation The integration_time sysfs attribute did not report the correct time. Changing the integration time would cause the reported lux to change wildly. Once the integration time was corrected, all of the equations, and lux tables needed to be corrected to match what the data sheets expected. This patch corrects all of this, and adds some more comments about how some of the constants were derived. Here are the results from testing a TSL2772 hooked up to a Raspberry Pi 2: # cat in_intensity0_integration_time 0.002730 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 # echo 0.65 > in_intensity0_integration_time # cat in_intensity0_integration_time 0.649740 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 with noticeable lag to lux changes in watch ; process. ; Now test the ALS calibration routine. # cat in_intensity0_calibbias 1000 # cat in_illuminance0_target_input 150 # echo 1 > in_illuminance0_calibrate # cat in_intensity0_calibbias 2777 # watch -n .1 cat in_illuminance0_input ; Lux now hovers around 150-155 The returned lux values were tested on a TSL2772 in various lighting conditions and the results are within the lux ranges described at https://en.wikipedia.org/wiki/Lux. The driver was primarily tested using a TSL2772, however some quick tests were also ran against the devices TSL2771, TSL2572, and TMD2772. Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-04 02:53:14 +00:00
update_struct_with_max_lux:
chip->als_cur_info.lux = max_lux;
ret = max_lux;
out_unlock:
mutex_unlock(&chip->als_mutex);
return ret;
}
/**
* tsl2772_get_prox() - Reads proximity data registers and updates
* chip->prox_data.
*
* @indio_dev: pointer to IIO device
*/
static int tsl2772_get_prox(struct iio_dev *indio_dev)
{
struct tsl2772_chip *chip = iio_priv(indio_dev);
int ret;
mutex_lock(&chip->prox_mutex);
ret = tsl2772_read_status(chip);
if (ret < 0)
goto prox_poll_err;
switch (chip->id) {
case tsl2571:
case tsl2671:
case tmd2671:
case tsl2771:
case tmd2771:
if (!(ret & TSL2772_STA_ADC_VALID)) {
ret = -EINVAL;
goto prox_poll_err;
}
break;
case tsl2572:
case tsl2672:
case tmd2672:
case tsl2772:
case tmd2772:
case apds9930:
if (!(ret & TSL2772_STA_PRX_VALID)) {
ret = -EINVAL;
goto prox_poll_err;
}
break;
}
ret = tsl2772_read_autoinc_regs(chip, TSL2772_PRX_LO, TSL2772_PRX_HI);
if (ret < 0)
goto prox_poll_err;
chip->prox_data = ret;
prox_poll_err:
mutex_unlock(&chip->prox_mutex);
return ret;
}
static int tsl2772_read_prox_led_current(struct tsl2772_chip *chip)
{
struct device_node *of_node = chip->client->dev.of_node;
int ret, tmp, i;
ret = of_property_read_u32(of_node, "led-max-microamp", &tmp);
if (ret < 0)
return ret;
for (i = 0; tsl2772_led_currents[i][0] != 0; i++) {
if (tmp == tsl2772_led_currents[i][0]) {
chip->settings.prox_power = tsl2772_led_currents[i][1];
return 0;
}
}
dev_err(&chip->client->dev, "Invalid value %d for led-max-microamp\n",
tmp);
return -EINVAL;
}
static int tsl2772_read_prox_diodes(struct tsl2772_chip *chip)
{
struct device_node *of_node = chip->client->dev.of_node;
int i, ret, num_leds, prox_diode_mask;
u32 leds[TSL2772_MAX_PROX_LEDS];
ret = of_property_count_u32_elems(of_node, "amstaos,proximity-diodes");
if (ret < 0)
return ret;
num_leds = ret;
if (num_leds > TSL2772_MAX_PROX_LEDS)
num_leds = TSL2772_MAX_PROX_LEDS;
ret = of_property_read_u32_array(of_node, "amstaos,proximity-diodes",
leds, num_leds);
if (ret < 0) {
dev_err(&chip->client->dev,
"Invalid value for amstaos,proximity-diodes: %d.\n",
ret);
return ret;
}
prox_diode_mask = 0;
for (i = 0; i < num_leds; i++) {
if (leds[i] == 0)
prox_diode_mask |= TSL2772_DIODE0;
else if (leds[i] == 1)
prox_diode_mask |= TSL2772_DIODE1;
else {
dev_err(&chip->client->dev,
"Invalid value %d in amstaos,proximity-diodes.\n",
leds[i]);
return -EINVAL;
}
}
return 0;
}
static void tsl2772_parse_dt(struct tsl2772_chip *chip)
{
tsl2772_read_prox_led_current(chip);
tsl2772_read_prox_diodes(chip);
}
/**
* tsl2772_defaults() - Populates the device nominal operating parameters
* with those provided by a 'platform' data struct or
* with prefined defaults.
*
* @chip: pointer to device structure.
*/
static void tsl2772_defaults(struct tsl2772_chip *chip)
{
/* If Operational settings defined elsewhere.. */
if (chip->pdata && chip->pdata->platform_default_settings)
memcpy(&chip->settings, chip->pdata->platform_default_settings,
sizeof(tsl2772_default_settings));
else
memcpy(&chip->settings, &tsl2772_default_settings,
sizeof(tsl2772_default_settings));
/* Load up the proper lux table. */
staging: iio: tsl2x7x: correct integration time and lux equation The integration_time sysfs attribute did not report the correct time. Changing the integration time would cause the reported lux to change wildly. Once the integration time was corrected, all of the equations, and lux tables needed to be corrected to match what the data sheets expected. This patch corrects all of this, and adds some more comments about how some of the constants were derived. Here are the results from testing a TSL2772 hooked up to a Raspberry Pi 2: # cat in_intensity0_integration_time 0.002730 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 # echo 0.65 > in_intensity0_integration_time # cat in_intensity0_integration_time 0.649740 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 with noticeable lag to lux changes in watch ; process. ; Now test the ALS calibration routine. # cat in_intensity0_calibbias 1000 # cat in_illuminance0_target_input 150 # echo 1 > in_illuminance0_calibrate # cat in_intensity0_calibbias 2777 # watch -n .1 cat in_illuminance0_input ; Lux now hovers around 150-155 The returned lux values were tested on a TSL2772 in various lighting conditions and the results are within the lux ranges described at https://en.wikipedia.org/wiki/Lux. The driver was primarily tested using a TSL2772, however some quick tests were also ran against the devices TSL2771, TSL2572, and TMD2772. Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-04 02:53:14 +00:00
if (chip->pdata && chip->pdata->platform_lux_table[0].ch0 != 0)
memcpy(chip->tsl2772_device_lux,
chip->pdata->platform_lux_table,
sizeof(chip->pdata->platform_lux_table));
else
memcpy(chip->tsl2772_device_lux,
tsl2772_default_lux_table_group[chip->id],
TSL2772_DEFAULT_TABLE_BYTES);
tsl2772_parse_dt(chip);
}
/**
* tsl2772_als_calibrate() - Obtain single reading and calculate
* the als_gain_trim.
*
* @indio_dev: pointer to IIO device
*/
static int tsl2772_als_calibrate(struct iio_dev *indio_dev)
{
struct tsl2772_chip *chip = iio_priv(indio_dev);
int ret, lux_val;
ret = i2c_smbus_read_byte_data(chip->client,
TSL2772_CMD_REG | TSL2772_CNTRL);
if (ret < 0) {
dev_err(&chip->client->dev,
"%s: failed to read from the CNTRL register\n",
__func__);
return ret;
}
if ((ret & (TSL2772_CNTL_ADC_ENBL | TSL2772_CNTL_PWR_ON))
!= (TSL2772_CNTL_ADC_ENBL | TSL2772_CNTL_PWR_ON)) {
dev_err(&chip->client->dev,
"%s: Device is not powered on and/or ADC is not enabled\n",
__func__);
return -EINVAL;
} else if ((ret & TSL2772_STA_ADC_VALID) != TSL2772_STA_ADC_VALID) {
dev_err(&chip->client->dev,
"%s: The two ADC channels have not completed an integration cycle\n",
__func__);
return -ENODATA;
}
lux_val = tsl2772_get_lux(indio_dev);
if (lux_val < 0) {
dev_err(&chip->client->dev,
"%s: failed to get lux\n", __func__);
return lux_val;
}
if (lux_val == 0)
return -ERANGE;
ret = (chip->settings.als_cal_target * chip->settings.als_gain_trim) /
lux_val;
if (ret < TSL2772_ALS_GAIN_TRIM_MIN || ret > TSL2772_ALS_GAIN_TRIM_MAX)
return -ERANGE;
chip->settings.als_gain_trim = ret;
return ret;
}
static void tsl2772_disable_regulators_action(void *_data)
{
struct tsl2772_chip *chip = _data;
regulator_bulk_disable(ARRAY_SIZE(chip->supplies), chip->supplies);
}
static int tsl2772_chip_on(struct iio_dev *indio_dev)
{
struct tsl2772_chip *chip = iio_priv(indio_dev);
staging: iio: tsl2x7x: correct integration time and lux equation The integration_time sysfs attribute did not report the correct time. Changing the integration time would cause the reported lux to change wildly. Once the integration time was corrected, all of the equations, and lux tables needed to be corrected to match what the data sheets expected. This patch corrects all of this, and adds some more comments about how some of the constants were derived. Here are the results from testing a TSL2772 hooked up to a Raspberry Pi 2: # cat in_intensity0_integration_time 0.002730 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 # echo 0.65 > in_intensity0_integration_time # cat in_intensity0_integration_time 0.649740 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 with noticeable lag to lux changes in watch ; process. ; Now test the ALS calibration routine. # cat in_intensity0_calibbias 1000 # cat in_illuminance0_target_input 150 # echo 1 > in_illuminance0_calibrate # cat in_intensity0_calibbias 2777 # watch -n .1 cat in_illuminance0_input ; Lux now hovers around 150-155 The returned lux values were tested on a TSL2772 in various lighting conditions and the results are within the lux ranges described at https://en.wikipedia.org/wiki/Lux. The driver was primarily tested using a TSL2772, however some quick tests were also ran against the devices TSL2771, TSL2572, and TMD2772. Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-04 02:53:14 +00:00
int ret, i, als_count, als_time_us;
u8 *dev_reg, reg_val;
/* Non calculated parameters */
chip->tsl2772_config[TSL2772_ALS_TIME] = chip->settings.als_time;
chip->tsl2772_config[TSL2772_PRX_TIME] = chip->settings.prox_time;
chip->tsl2772_config[TSL2772_WAIT_TIME] = chip->settings.wait_time;
chip->tsl2772_config[TSL2772_ALS_PRX_CONFIG] =
chip->settings.als_prox_config;
chip->tsl2772_config[TSL2772_ALS_MINTHRESHLO] =
(chip->settings.als_thresh_low) & 0xFF;
chip->tsl2772_config[TSL2772_ALS_MINTHRESHHI] =
(chip->settings.als_thresh_low >> 8) & 0xFF;
chip->tsl2772_config[TSL2772_ALS_MAXTHRESHLO] =
(chip->settings.als_thresh_high) & 0xFF;
chip->tsl2772_config[TSL2772_ALS_MAXTHRESHHI] =
(chip->settings.als_thresh_high >> 8) & 0xFF;
chip->tsl2772_config[TSL2772_PERSISTENCE] =
(chip->settings.prox_persistence & 0xFF) << 4 |
(chip->settings.als_persistence & 0xFF);
chip->tsl2772_config[TSL2772_PRX_COUNT] =
chip->settings.prox_pulse_count;
chip->tsl2772_config[TSL2772_PRX_MINTHRESHLO] =
(chip->settings.prox_thres_low) & 0xFF;
chip->tsl2772_config[TSL2772_PRX_MINTHRESHHI] =
(chip->settings.prox_thres_low >> 8) & 0xFF;
chip->tsl2772_config[TSL2772_PRX_MAXTHRESHLO] =
(chip->settings.prox_thres_high) & 0xFF;
chip->tsl2772_config[TSL2772_PRX_MAXTHRESHHI] =
(chip->settings.prox_thres_high >> 8) & 0xFF;
/* and make sure we're not already on */
if (chip->tsl2772_chip_status == TSL2772_CHIP_WORKING) {
/* if forcing a register update - turn off, then on */
dev_info(&chip->client->dev, "device is already enabled\n");
return -EINVAL;
}
/* Set the gain based on tsl2772_settings struct */
chip->tsl2772_config[TSL2772_GAIN] =
(chip->settings.als_gain & 0xFF) |
((chip->settings.prox_gain & 0xFF) << 2) |
(chip->settings.prox_diode << 4) |
(chip->settings.prox_power << 6);
staging: iio: tsl2x7x: correct integration time and lux equation The integration_time sysfs attribute did not report the correct time. Changing the integration time would cause the reported lux to change wildly. Once the integration time was corrected, all of the equations, and lux tables needed to be corrected to match what the data sheets expected. This patch corrects all of this, and adds some more comments about how some of the constants were derived. Here are the results from testing a TSL2772 hooked up to a Raspberry Pi 2: # cat in_intensity0_integration_time 0.002730 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 # echo 0.65 > in_intensity0_integration_time # cat in_intensity0_integration_time 0.649740 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 with noticeable lag to lux changes in watch ; process. ; Now test the ALS calibration routine. # cat in_intensity0_calibbias 1000 # cat in_illuminance0_target_input 150 # echo 1 > in_illuminance0_calibrate # cat in_intensity0_calibbias 2777 # watch -n .1 cat in_illuminance0_input ; Lux now hovers around 150-155 The returned lux values were tested on a TSL2772 in various lighting conditions and the results are within the lux ranges described at https://en.wikipedia.org/wiki/Lux. The driver was primarily tested using a TSL2772, however some quick tests were also ran against the devices TSL2771, TSL2572, and TMD2772. Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-04 02:53:14 +00:00
/* set chip time scaling and saturation */
als_count = 256 - chip->settings.als_time;
als_time_us = als_count * tsl2772_int_time_avail[chip->id][3];
staging: iio: tsl2x7x: correct integration time and lux equation The integration_time sysfs attribute did not report the correct time. Changing the integration time would cause the reported lux to change wildly. Once the integration time was corrected, all of the equations, and lux tables needed to be corrected to match what the data sheets expected. This patch corrects all of this, and adds some more comments about how some of the constants were derived. Here are the results from testing a TSL2772 hooked up to a Raspberry Pi 2: # cat in_intensity0_integration_time 0.002730 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 # echo 0.65 > in_intensity0_integration_time # cat in_intensity0_integration_time 0.649740 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 with noticeable lag to lux changes in watch ; process. ; Now test the ALS calibration routine. # cat in_intensity0_calibbias 1000 # cat in_illuminance0_target_input 150 # echo 1 > in_illuminance0_calibrate # cat in_intensity0_calibbias 2777 # watch -n .1 cat in_illuminance0_input ; Lux now hovers around 150-155 The returned lux values were tested on a TSL2772 in various lighting conditions and the results are within the lux ranges described at https://en.wikipedia.org/wiki/Lux. The driver was primarily tested using a TSL2772, however some quick tests were also ran against the devices TSL2771, TSL2572, and TMD2772. Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-04 02:53:14 +00:00
chip->als_saturation = als_count * 768; /* 75% of full scale */
chip->als_gain_time_scale = als_time_us *
tsl2772_als_gain[chip->settings.als_gain];
/*
* TSL2772 Specific power-on / adc enable sequence
* Power on the device 1st.
*/
ret = tsl2772_write_control_reg(chip, TSL2772_CNTL_PWR_ON);
if (ret < 0)
return ret;
/*
* Use the following shadow copy for our delay before enabling ADC.
* Write all the registers.
*/
for (i = 0, dev_reg = chip->tsl2772_config;
i < TSL2772_MAX_CONFIG_REG; i++) {
int reg = TSL2772_CMD_REG + i;
ret = i2c_smbus_write_byte_data(chip->client, reg,
*dev_reg++);
if (ret < 0) {
dev_err(&chip->client->dev,
"%s: failed to write to register %x: %d\n",
__func__, reg, ret);
return ret;
}
}
/* Power-on settling time */
usleep_range(3000, 3500);
reg_val = TSL2772_CNTL_PWR_ON | TSL2772_CNTL_ADC_ENBL |
TSL2772_CNTL_PROX_DET_ENBL;
if (chip->settings.als_interrupt_en)
reg_val |= TSL2772_CNTL_ALS_INT_ENBL;
if (chip->settings.prox_interrupt_en)
reg_val |= TSL2772_CNTL_PROX_INT_ENBL;
ret = tsl2772_write_control_reg(chip, reg_val);
if (ret < 0)
return ret;
ret = i2c_smbus_write_byte(chip->client,
TSL2772_CMD_REG | TSL2772_CMD_SPL_FN |
TSL2772_CMD_PROXALS_INT_CLR);
if (ret < 0) {
dev_err(&chip->client->dev,
"%s: failed to clear interrupt status: %d\n",
__func__, ret);
return ret;
}
chip->tsl2772_chip_status = TSL2772_CHIP_WORKING;
return ret;
}
static int tsl2772_chip_off(struct iio_dev *indio_dev)
{
struct tsl2772_chip *chip = iio_priv(indio_dev);
/* turn device off */
chip->tsl2772_chip_status = TSL2772_CHIP_SUSPENDED;
return tsl2772_write_control_reg(chip, 0x00);
}
static void tsl2772_chip_off_action(void *data)
{
struct iio_dev *indio_dev = data;
tsl2772_chip_off(indio_dev);
}
/**
* tsl2772_invoke_change - power cycle the device to implement the user
* parameters
* @indio_dev: pointer to IIO device
*
* Obtain and lock both ALS and PROX resources, determine and save device state
* (On/Off), cycle device to implement updated parameter, put device back into
* proper state, and unlock resource.
*/
static int tsl2772_invoke_change(struct iio_dev *indio_dev)
{
struct tsl2772_chip *chip = iio_priv(indio_dev);
int device_status = chip->tsl2772_chip_status;
int ret;
mutex_lock(&chip->als_mutex);
mutex_lock(&chip->prox_mutex);
if (device_status == TSL2772_CHIP_WORKING) {
ret = tsl2772_chip_off(indio_dev);
if (ret < 0)
goto unlock;
}
ret = tsl2772_chip_on(indio_dev);
unlock:
mutex_unlock(&chip->prox_mutex);
mutex_unlock(&chip->als_mutex);
return ret;
}
static int tsl2772_prox_cal(struct iio_dev *indio_dev)
{
struct tsl2772_chip *chip = iio_priv(indio_dev);
int prox_history[MAX_SAMPLES_CAL + 1];
int i, ret, mean, max, sample_sum;
if (chip->settings.prox_max_samples_cal < 1 ||
chip->settings.prox_max_samples_cal > MAX_SAMPLES_CAL)
return -EINVAL;
for (i = 0; i < chip->settings.prox_max_samples_cal; i++) {
usleep_range(15000, 17500);
ret = tsl2772_get_prox(indio_dev);
if (ret < 0)
return ret;
prox_history[i] = chip->prox_data;
}
sample_sum = 0;
max = INT_MIN;
for (i = 0; i < chip->settings.prox_max_samples_cal; i++) {
sample_sum += prox_history[i];
max = max(max, prox_history[i]);
}
mean = sample_sum / chip->settings.prox_max_samples_cal;
chip->settings.prox_thres_high = (max << 1) - mean;
return tsl2772_invoke_change(indio_dev);
}
static int tsl2772_read_avail(struct iio_dev *indio_dev,
struct iio_chan_spec const *chan,
const int **vals, int *type, int *length,
long mask)
{
struct tsl2772_chip *chip = iio_priv(indio_dev);
switch (mask) {
case IIO_CHAN_INFO_CALIBSCALE:
if (chan->type == IIO_INTENSITY) {
*length = ARRAY_SIZE(tsl2772_int_calibscale_avail);
*vals = tsl2772_int_calibscale_avail;
} else {
*length = ARRAY_SIZE(tsl2772_prox_calibscale_avail);
*vals = tsl2772_prox_calibscale_avail;
}
*type = IIO_VAL_INT;
return IIO_AVAIL_LIST;
case IIO_CHAN_INFO_INT_TIME:
*length = ARRAY_SIZE(tsl2772_int_time_avail[chip->id]);
*vals = tsl2772_int_time_avail[chip->id];
*type = IIO_VAL_INT_PLUS_MICRO;
return IIO_AVAIL_RANGE;
}
return -EINVAL;
}
static ssize_t in_illuminance0_target_input_show(struct device *dev,
struct device_attribute *attr,
char *buf)
{
struct tsl2772_chip *chip = iio_priv(dev_to_iio_dev(dev));
return scnprintf(buf, PAGE_SIZE, "%d\n", chip->settings.als_cal_target);
}
static ssize_t in_illuminance0_target_input_store(struct device *dev,
struct device_attribute *attr,
const char *buf, size_t len)
{
struct iio_dev *indio_dev = dev_to_iio_dev(dev);
struct tsl2772_chip *chip = iio_priv(indio_dev);
u16 value;
int ret;
if (kstrtou16(buf, 0, &value))
return -EINVAL;
chip->settings.als_cal_target = value;
ret = tsl2772_invoke_change(indio_dev);
if (ret < 0)
return ret;
return len;
}
static ssize_t in_illuminance0_calibrate_store(struct device *dev,
struct device_attribute *attr,
const char *buf, size_t len)
{
struct iio_dev *indio_dev = dev_to_iio_dev(dev);
bool value;
int ret;
if (kstrtobool(buf, &value) || !value)
return -EINVAL;
ret = tsl2772_als_calibrate(indio_dev);
if (ret < 0)
return ret;
ret = tsl2772_invoke_change(indio_dev);
if (ret < 0)
return ret;
return len;
}
static ssize_t in_illuminance0_lux_table_show(struct device *dev,
struct device_attribute *attr,
char *buf)
{
struct tsl2772_chip *chip = iio_priv(dev_to_iio_dev(dev));
int i = 0;
int offset = 0;
while (i < TSL2772_MAX_LUX_TABLE_SIZE) {
offset += scnprintf(buf + offset, PAGE_SIZE - offset, "%u,%u,",
chip->tsl2772_device_lux[i].ch0,
chip->tsl2772_device_lux[i].ch1);
if (chip->tsl2772_device_lux[i].ch0 == 0) {
/*
* We just printed the first "0" entry.
* Now get rid of the extra "," and break.
*/
offset--;
break;
}
i++;
}
offset += scnprintf(buf + offset, PAGE_SIZE - offset, "\n");
return offset;
}
static ssize_t in_illuminance0_lux_table_store(struct device *dev,
struct device_attribute *attr,
const char *buf, size_t len)
{
struct iio_dev *indio_dev = dev_to_iio_dev(dev);
struct tsl2772_chip *chip = iio_priv(indio_dev);
int value[ARRAY_SIZE(chip->tsl2772_device_lux) * 2 + 1];
int n, ret;
get_options(buf, ARRAY_SIZE(value), value);
/*
* We now have an array of ints starting at value[1], and
* enumerated by value[0].
staging: iio: tsl2x7x: correct integration time and lux equation The integration_time sysfs attribute did not report the correct time. Changing the integration time would cause the reported lux to change wildly. Once the integration time was corrected, all of the equations, and lux tables needed to be corrected to match what the data sheets expected. This patch corrects all of this, and adds some more comments about how some of the constants were derived. Here are the results from testing a TSL2772 hooked up to a Raspberry Pi 2: # cat in_intensity0_integration_time 0.002730 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 # echo 0.65 > in_intensity0_integration_time # cat in_intensity0_integration_time 0.649740 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 with noticeable lag to lux changes in watch ; process. ; Now test the ALS calibration routine. # cat in_intensity0_calibbias 1000 # cat in_illuminance0_target_input 150 # echo 1 > in_illuminance0_calibrate # cat in_intensity0_calibbias 2777 # watch -n .1 cat in_illuminance0_input ; Lux now hovers around 150-155 The returned lux values were tested on a TSL2772 in various lighting conditions and the results are within the lux ranges described at https://en.wikipedia.org/wiki/Lux. The driver was primarily tested using a TSL2772, however some quick tests were also ran against the devices TSL2771, TSL2572, and TMD2772. Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-04 02:53:14 +00:00
* We expect each group of two ints to be one table entry,
* and the last table entry is all 0.
*/
n = value[0];
staging: iio: tsl2x7x: correct integration time and lux equation The integration_time sysfs attribute did not report the correct time. Changing the integration time would cause the reported lux to change wildly. Once the integration time was corrected, all of the equations, and lux tables needed to be corrected to match what the data sheets expected. This patch corrects all of this, and adds some more comments about how some of the constants were derived. Here are the results from testing a TSL2772 hooked up to a Raspberry Pi 2: # cat in_intensity0_integration_time 0.002730 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 # echo 0.65 > in_intensity0_integration_time # cat in_intensity0_integration_time 0.649740 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 with noticeable lag to lux changes in watch ; process. ; Now test the ALS calibration routine. # cat in_intensity0_calibbias 1000 # cat in_illuminance0_target_input 150 # echo 1 > in_illuminance0_calibrate # cat in_intensity0_calibbias 2777 # watch -n .1 cat in_illuminance0_input ; Lux now hovers around 150-155 The returned lux values were tested on a TSL2772 in various lighting conditions and the results are within the lux ranges described at https://en.wikipedia.org/wiki/Lux. The driver was primarily tested using a TSL2772, however some quick tests were also ran against the devices TSL2771, TSL2572, and TMD2772. Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-04 02:53:14 +00:00
if ((n % 2) || n < 4 ||
n > ((ARRAY_SIZE(chip->tsl2772_device_lux) - 1) * 2))
return -EINVAL;
staging: iio: tsl2x7x: correct integration time and lux equation The integration_time sysfs attribute did not report the correct time. Changing the integration time would cause the reported lux to change wildly. Once the integration time was corrected, all of the equations, and lux tables needed to be corrected to match what the data sheets expected. This patch corrects all of this, and adds some more comments about how some of the constants were derived. Here are the results from testing a TSL2772 hooked up to a Raspberry Pi 2: # cat in_intensity0_integration_time 0.002730 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 # echo 0.65 > in_intensity0_integration_time # cat in_intensity0_integration_time 0.649740 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 with noticeable lag to lux changes in watch ; process. ; Now test the ALS calibration routine. # cat in_intensity0_calibbias 1000 # cat in_illuminance0_target_input 150 # echo 1 > in_illuminance0_calibrate # cat in_intensity0_calibbias 2777 # watch -n .1 cat in_illuminance0_input ; Lux now hovers around 150-155 The returned lux values were tested on a TSL2772 in various lighting conditions and the results are within the lux ranges described at https://en.wikipedia.org/wiki/Lux. The driver was primarily tested using a TSL2772, however some quick tests were also ran against the devices TSL2771, TSL2572, and TMD2772. Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-04 02:53:14 +00:00
if ((value[(n - 1)] | value[n]) != 0)
return -EINVAL;
if (chip->tsl2772_chip_status == TSL2772_CHIP_WORKING) {
ret = tsl2772_chip_off(indio_dev);
if (ret < 0)
return ret;
}
/* Zero out the table */
memset(chip->tsl2772_device_lux, 0, sizeof(chip->tsl2772_device_lux));
memcpy(chip->tsl2772_device_lux, &value[1], (value[0] * 4));
ret = tsl2772_invoke_change(indio_dev);
if (ret < 0)
return ret;
return len;
}
static ssize_t in_proximity0_calibrate_store(struct device *dev,
struct device_attribute *attr,
const char *buf, size_t len)
{
struct iio_dev *indio_dev = dev_to_iio_dev(dev);
bool value;
int ret;
if (kstrtobool(buf, &value) || !value)
return -EINVAL;
ret = tsl2772_prox_cal(indio_dev);
if (ret < 0)
return ret;
ret = tsl2772_invoke_change(indio_dev);
if (ret < 0)
return ret;
return len;
}
static int tsl2772_read_interrupt_config(struct iio_dev *indio_dev,
const struct iio_chan_spec *chan,
enum iio_event_type type,
enum iio_event_direction dir)
{
struct tsl2772_chip *chip = iio_priv(indio_dev);
if (chan->type == IIO_INTENSITY)
return chip->settings.als_interrupt_en;
else
return chip->settings.prox_interrupt_en;
}
static int tsl2772_write_interrupt_config(struct iio_dev *indio_dev,
const struct iio_chan_spec *chan,
enum iio_event_type type,
enum iio_event_direction dir,
int val)
{
struct tsl2772_chip *chip = iio_priv(indio_dev);
if (chan->type == IIO_INTENSITY)
chip->settings.als_interrupt_en = val ? true : false;
else
chip->settings.prox_interrupt_en = val ? true : false;
return tsl2772_invoke_change(indio_dev);
}
static int tsl2772_write_event_value(struct iio_dev *indio_dev,
const struct iio_chan_spec *chan,
enum iio_event_type type,
enum iio_event_direction dir,
enum iio_event_info info,
int val, int val2)
{
struct tsl2772_chip *chip = iio_priv(indio_dev);
int ret = -EINVAL, count, persistence;
u8 time;
switch (info) {
case IIO_EV_INFO_VALUE:
if (chan->type == IIO_INTENSITY) {
switch (dir) {
case IIO_EV_DIR_RISING:
chip->settings.als_thresh_high = val;
ret = 0;
break;
case IIO_EV_DIR_FALLING:
chip->settings.als_thresh_low = val;
ret = 0;
break;
default:
break;
}
} else {
switch (dir) {
case IIO_EV_DIR_RISING:
chip->settings.prox_thres_high = val;
ret = 0;
break;
case IIO_EV_DIR_FALLING:
chip->settings.prox_thres_low = val;
ret = 0;
break;
default:
break;
}
}
break;
case IIO_EV_INFO_PERIOD:
if (chan->type == IIO_INTENSITY)
time = chip->settings.als_time;
else
time = chip->settings.prox_time;
count = 256 - time;
persistence = ((val * 1000000) + val2) /
(count * tsl2772_int_time_avail[chip->id][3]);
if (chan->type == IIO_INTENSITY) {
/* ALS filter values are 1, 2, 3, 5, 10, 15, ..., 60 */
if (persistence > 3)
persistence = (persistence / 5) + 3;
chip->settings.als_persistence = persistence;
} else {
chip->settings.prox_persistence = persistence;
}
ret = 0;
break;
default:
break;
}
if (ret < 0)
return ret;
return tsl2772_invoke_change(indio_dev);
}
static int tsl2772_read_event_value(struct iio_dev *indio_dev,
const struct iio_chan_spec *chan,
enum iio_event_type type,
enum iio_event_direction dir,
enum iio_event_info info,
int *val, int *val2)
{
struct tsl2772_chip *chip = iio_priv(indio_dev);
int filter_delay, persistence;
u8 time;
switch (info) {
case IIO_EV_INFO_VALUE:
if (chan->type == IIO_INTENSITY) {
switch (dir) {
case IIO_EV_DIR_RISING:
*val = chip->settings.als_thresh_high;
return IIO_VAL_INT;
case IIO_EV_DIR_FALLING:
*val = chip->settings.als_thresh_low;
return IIO_VAL_INT;
default:
return -EINVAL;
}
} else {
switch (dir) {
case IIO_EV_DIR_RISING:
*val = chip->settings.prox_thres_high;
return IIO_VAL_INT;
case IIO_EV_DIR_FALLING:
*val = chip->settings.prox_thres_low;
return IIO_VAL_INT;
default:
return -EINVAL;
}
}
break;
case IIO_EV_INFO_PERIOD:
if (chan->type == IIO_INTENSITY) {
time = chip->settings.als_time;
persistence = chip->settings.als_persistence;
/* ALS filter values are 1, 2, 3, 5, 10, 15, ..., 60 */
if (persistence > 3)
persistence = (persistence - 3) * 5;
} else {
time = chip->settings.prox_time;
persistence = chip->settings.prox_persistence;
}
filter_delay = persistence * (256 - time) *
tsl2772_int_time_avail[chip->id][3];
*val = filter_delay / 1000000;
*val2 = filter_delay % 1000000;
return IIO_VAL_INT_PLUS_MICRO;
default:
return -EINVAL;
}
}
static int tsl2772_read_raw(struct iio_dev *indio_dev,
struct iio_chan_spec const *chan,
int *val,
int *val2,
long mask)
{
struct tsl2772_chip *chip = iio_priv(indio_dev);
switch (mask) {
case IIO_CHAN_INFO_PROCESSED:
switch (chan->type) {
case IIO_LIGHT:
tsl2772_get_lux(indio_dev);
*val = chip->als_cur_info.lux;
return IIO_VAL_INT;
default:
return -EINVAL;
}
case IIO_CHAN_INFO_RAW:
switch (chan->type) {
case IIO_INTENSITY:
tsl2772_get_lux(indio_dev);
if (chan->channel == 0)
*val = chip->als_cur_info.als_ch0;
else
*val = chip->als_cur_info.als_ch1;
return IIO_VAL_INT;
case IIO_PROXIMITY:
tsl2772_get_prox(indio_dev);
*val = chip->prox_data;
return IIO_VAL_INT;
default:
return -EINVAL;
}
break;
case IIO_CHAN_INFO_CALIBSCALE:
if (chan->type == IIO_LIGHT)
*val = tsl2772_als_gain[chip->settings.als_gain];
else
*val = tsl2772_prox_gain[chip->settings.prox_gain];
return IIO_VAL_INT;
case IIO_CHAN_INFO_CALIBBIAS:
*val = chip->settings.als_gain_trim;
return IIO_VAL_INT;
case IIO_CHAN_INFO_INT_TIME:
staging: iio: tsl2x7x: correct integration time and lux equation The integration_time sysfs attribute did not report the correct time. Changing the integration time would cause the reported lux to change wildly. Once the integration time was corrected, all of the equations, and lux tables needed to be corrected to match what the data sheets expected. This patch corrects all of this, and adds some more comments about how some of the constants were derived. Here are the results from testing a TSL2772 hooked up to a Raspberry Pi 2: # cat in_intensity0_integration_time 0.002730 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 # echo 0.65 > in_intensity0_integration_time # cat in_intensity0_integration_time 0.649740 # watch -n .1 cat in_illuminance0_input ; Lux hovers around 55 with noticeable lag to lux changes in watch ; process. ; Now test the ALS calibration routine. # cat in_intensity0_calibbias 1000 # cat in_illuminance0_target_input 150 # echo 1 > in_illuminance0_calibrate # cat in_intensity0_calibbias 2777 # watch -n .1 cat in_illuminance0_input ; Lux now hovers around 150-155 The returned lux values were tested on a TSL2772 in various lighting conditions and the results are within the lux ranges described at https://en.wikipedia.org/wiki/Lux. The driver was primarily tested using a TSL2772, however some quick tests were also ran against the devices TSL2771, TSL2572, and TMD2772. Signed-off-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-05-04 02:53:14 +00:00
*val = 0;
*val2 = (256 - chip->settings.als_time) *
tsl2772_int_time_avail[chip->id][3];
return IIO_VAL_INT_PLUS_MICRO;
default:
return -EINVAL;
}
}
static int tsl2772_write_raw(struct iio_dev *indio_dev,
struct iio_chan_spec const *chan,
int val,
int val2,
long mask)
{
struct tsl2772_chip *chip = iio_priv(indio_dev);
switch (mask) {
case IIO_CHAN_INFO_CALIBSCALE:
if (chan->type == IIO_INTENSITY) {
switch (val) {
case 1:
chip->settings.als_gain = 0;
break;
case 8:
chip->settings.als_gain = 1;
break;
case 16:
chip->settings.als_gain = 2;
break;
case 120:
chip->settings.als_gain = 3;
break;
default:
return -EINVAL;
}
} else {
switch (val) {
case 1:
chip->settings.prox_gain = 0;
break;
case 2:
chip->settings.prox_gain = 1;
break;
case 4:
chip->settings.prox_gain = 2;
break;
case 8:
chip->settings.prox_gain = 3;
break;
default:
return -EINVAL;
}
}
break;
case IIO_CHAN_INFO_CALIBBIAS:
if (val < TSL2772_ALS_GAIN_TRIM_MIN ||
val > TSL2772_ALS_GAIN_TRIM_MAX)
return -EINVAL;
chip->settings.als_gain_trim = val;
break;
case IIO_CHAN_INFO_INT_TIME:
if (val != 0 || val2 < tsl2772_int_time_avail[chip->id][1] ||
val2 > tsl2772_int_time_avail[chip->id][5])
return -EINVAL;
chip->settings.als_time = 256 -
(val2 / tsl2772_int_time_avail[chip->id][3]);
break;
default:
return -EINVAL;
}
return tsl2772_invoke_change(indio_dev);
}
static DEVICE_ATTR_RW(in_illuminance0_target_input);
static DEVICE_ATTR_WO(in_illuminance0_calibrate);
static DEVICE_ATTR_WO(in_proximity0_calibrate);
static DEVICE_ATTR_RW(in_illuminance0_lux_table);
/* Use the default register values to identify the Taos device */
static int tsl2772_device_id_verif(int id, int target)
{
switch (target) {
case tsl2571:
case tsl2671:
case tsl2771:
return (id & 0xf0) == TRITON_ID;
case tmd2671:
case tmd2771:
return (id & 0xf0) == HALIBUT_ID;
case tsl2572:
case tsl2672:
case tmd2672:
case tsl2772:
case tmd2772:
case apds9930:
return (id & 0xf0) == SWORDFISH_ID;
}
return -EINVAL;
}
static irqreturn_t tsl2772_event_handler(int irq, void *private)
{
struct iio_dev *indio_dev = private;
struct tsl2772_chip *chip = iio_priv(indio_dev);
s64 timestamp = iio_get_time_ns(indio_dev);
int ret;
ret = tsl2772_read_status(chip);
if (ret < 0)
return IRQ_HANDLED;
/* What type of interrupt do we need to process */
if (ret & TSL2772_STA_PRX_INTR) {
iio_push_event(indio_dev,
IIO_UNMOD_EVENT_CODE(IIO_PROXIMITY,
0,
IIO_EV_TYPE_THRESH,
IIO_EV_DIR_EITHER),
timestamp);
}
if (ret & TSL2772_STA_ALS_INTR) {
iio_push_event(indio_dev,
IIO_UNMOD_EVENT_CODE(IIO_LIGHT,
0,
IIO_EV_TYPE_THRESH,
IIO_EV_DIR_EITHER),
timestamp);
}
ret = i2c_smbus_write_byte(chip->client,
TSL2772_CMD_REG | TSL2772_CMD_SPL_FN |
TSL2772_CMD_PROXALS_INT_CLR);
if (ret < 0)
dev_err(&chip->client->dev,
"%s: failed to clear interrupt status: %d\n",
__func__, ret);
return IRQ_HANDLED;
}
static struct attribute *tsl2772_ALS_device_attrs[] = {
&dev_attr_in_illuminance0_target_input.attr,
&dev_attr_in_illuminance0_calibrate.attr,
&dev_attr_in_illuminance0_lux_table.attr,
NULL
};
static struct attribute *tsl2772_PRX_device_attrs[] = {
&dev_attr_in_proximity0_calibrate.attr,
NULL
};
static struct attribute *tsl2772_ALSPRX_device_attrs[] = {
&dev_attr_in_illuminance0_target_input.attr,
&dev_attr_in_illuminance0_calibrate.attr,
&dev_attr_in_illuminance0_lux_table.attr,
NULL
};
static struct attribute *tsl2772_PRX2_device_attrs[] = {
&dev_attr_in_proximity0_calibrate.attr,
NULL
};
static struct attribute *tsl2772_ALSPRX2_device_attrs[] = {
&dev_attr_in_illuminance0_target_input.attr,
&dev_attr_in_illuminance0_calibrate.attr,
&dev_attr_in_illuminance0_lux_table.attr,
&dev_attr_in_proximity0_calibrate.attr,
NULL
};
static const struct attribute_group tsl2772_device_attr_group_tbl[] = {
[ALS] = {
.attrs = tsl2772_ALS_device_attrs,
},
[PRX] = {
.attrs = tsl2772_PRX_device_attrs,
},
[ALSPRX] = {
.attrs = tsl2772_ALSPRX_device_attrs,
},
[PRX2] = {
.attrs = tsl2772_PRX2_device_attrs,
},
[ALSPRX2] = {
.attrs = tsl2772_ALSPRX2_device_attrs,
},
};
#define TSL2772_DEVICE_INFO(type)[type] = \
{ \
.attrs = &tsl2772_device_attr_group_tbl[type], \
.read_raw = &tsl2772_read_raw, \
.read_avail = &tsl2772_read_avail, \
.write_raw = &tsl2772_write_raw, \
.read_event_value = &tsl2772_read_event_value, \
.write_event_value = &tsl2772_write_event_value, \
.read_event_config = &tsl2772_read_interrupt_config, \
.write_event_config = &tsl2772_write_interrupt_config, \
}
static const struct iio_info tsl2772_device_info[] = {
TSL2772_DEVICE_INFO(ALS),
TSL2772_DEVICE_INFO(PRX),
TSL2772_DEVICE_INFO(ALSPRX),
TSL2772_DEVICE_INFO(PRX2),
TSL2772_DEVICE_INFO(ALSPRX2),
};
static const struct iio_event_spec tsl2772_events[] = {
{
.type = IIO_EV_TYPE_THRESH,
.dir = IIO_EV_DIR_RISING,
.mask_separate = BIT(IIO_EV_INFO_VALUE),
}, {
.type = IIO_EV_TYPE_THRESH,
.dir = IIO_EV_DIR_FALLING,
.mask_separate = BIT(IIO_EV_INFO_VALUE),
}, {
.type = IIO_EV_TYPE_THRESH,
.dir = IIO_EV_DIR_EITHER,
.mask_separate = BIT(IIO_EV_INFO_PERIOD) |
BIT(IIO_EV_INFO_ENABLE),
},
};
static const struct tsl2772_chip_info tsl2772_chip_info_tbl[] = {
[ALS] = {
.channel_with_events = {
{
.type = IIO_LIGHT,
.indexed = 1,
.channel = 0,
.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
}, {
.type = IIO_INTENSITY,
.indexed = 1,
.channel = 0,
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
BIT(IIO_CHAN_INFO_INT_TIME) |
BIT(IIO_CHAN_INFO_CALIBSCALE) |
BIT(IIO_CHAN_INFO_CALIBBIAS),
.info_mask_separate_available =
BIT(IIO_CHAN_INFO_INT_TIME) |
BIT(IIO_CHAN_INFO_CALIBSCALE),
.event_spec = tsl2772_events,
.num_event_specs = ARRAY_SIZE(tsl2772_events),
}, {
.type = IIO_INTENSITY,
.indexed = 1,
.channel = 1,
},
},
.channel_without_events = {
{
.type = IIO_LIGHT,
.indexed = 1,
.channel = 0,
.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
}, {
.type = IIO_INTENSITY,
.indexed = 1,
.channel = 0,
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
BIT(IIO_CHAN_INFO_INT_TIME) |
BIT(IIO_CHAN_INFO_CALIBSCALE) |
BIT(IIO_CHAN_INFO_CALIBBIAS),
.info_mask_separate_available =
BIT(IIO_CHAN_INFO_INT_TIME) |
BIT(IIO_CHAN_INFO_CALIBSCALE),
}, {
.type = IIO_INTENSITY,
.indexed = 1,
.channel = 1,
},
},
.chan_table_elements = 3,
.info = &tsl2772_device_info[ALS],
},
[PRX] = {
.channel_with_events = {
{
.type = IIO_PROXIMITY,
.indexed = 1,
.channel = 0,
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
.event_spec = tsl2772_events,
.num_event_specs = ARRAY_SIZE(tsl2772_events),
},
},
.channel_without_events = {
{
.type = IIO_PROXIMITY,
.indexed = 1,
.channel = 0,
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
},
},
.chan_table_elements = 1,
.info = &tsl2772_device_info[PRX],
},
[ALSPRX] = {
.channel_with_events = {
{
.type = IIO_LIGHT,
.indexed = 1,
.channel = 0,
.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
}, {
.type = IIO_INTENSITY,
.indexed = 1,
.channel = 0,
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
BIT(IIO_CHAN_INFO_INT_TIME) |
BIT(IIO_CHAN_INFO_CALIBSCALE) |
BIT(IIO_CHAN_INFO_CALIBBIAS),
.info_mask_separate_available =
BIT(IIO_CHAN_INFO_INT_TIME) |
BIT(IIO_CHAN_INFO_CALIBSCALE),
.event_spec = tsl2772_events,
.num_event_specs = ARRAY_SIZE(tsl2772_events),
}, {
.type = IIO_INTENSITY,
.indexed = 1,
.channel = 1,
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
}, {
.type = IIO_PROXIMITY,
.indexed = 1,
.channel = 0,
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
.event_spec = tsl2772_events,
.num_event_specs = ARRAY_SIZE(tsl2772_events),
},
},
.channel_without_events = {
{
.type = IIO_LIGHT,
.indexed = 1,
.channel = 0,
.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
}, {
.type = IIO_INTENSITY,
.indexed = 1,
.channel = 0,
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
BIT(IIO_CHAN_INFO_INT_TIME) |
BIT(IIO_CHAN_INFO_CALIBSCALE) |
BIT(IIO_CHAN_INFO_CALIBBIAS),
.info_mask_separate_available =
BIT(IIO_CHAN_INFO_INT_TIME) |
BIT(IIO_CHAN_INFO_CALIBSCALE),
}, {
.type = IIO_INTENSITY,
.indexed = 1,
.channel = 1,
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
}, {
.type = IIO_PROXIMITY,
.indexed = 1,
.channel = 0,
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
},
},
.chan_table_elements = 4,
.info = &tsl2772_device_info[ALSPRX],
},
[PRX2] = {
.channel_with_events = {
{
.type = IIO_PROXIMITY,
.indexed = 1,
.channel = 0,
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
BIT(IIO_CHAN_INFO_CALIBSCALE),
.info_mask_separate_available =
BIT(IIO_CHAN_INFO_CALIBSCALE),
.event_spec = tsl2772_events,
.num_event_specs = ARRAY_SIZE(tsl2772_events),
},
},
.channel_without_events = {
{
.type = IIO_PROXIMITY,
.indexed = 1,
.channel = 0,
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
BIT(IIO_CHAN_INFO_CALIBSCALE),
.info_mask_separate_available =
BIT(IIO_CHAN_INFO_CALIBSCALE),
},
},
.chan_table_elements = 1,
.info = &tsl2772_device_info[PRX2],
},
[ALSPRX2] = {
.channel_with_events = {
{
.type = IIO_LIGHT,
.indexed = 1,
.channel = 0,
.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
}, {
.type = IIO_INTENSITY,
.indexed = 1,
.channel = 0,
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
BIT(IIO_CHAN_INFO_INT_TIME) |
BIT(IIO_CHAN_INFO_CALIBSCALE) |
BIT(IIO_CHAN_INFO_CALIBBIAS),
.info_mask_separate_available =
BIT(IIO_CHAN_INFO_INT_TIME) |
BIT(IIO_CHAN_INFO_CALIBSCALE),
.event_spec = tsl2772_events,
.num_event_specs = ARRAY_SIZE(tsl2772_events),
}, {
.type = IIO_INTENSITY,
.indexed = 1,
.channel = 1,
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
}, {
.type = IIO_PROXIMITY,
.indexed = 1,
.channel = 0,
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
BIT(IIO_CHAN_INFO_CALIBSCALE),
.info_mask_separate_available =
BIT(IIO_CHAN_INFO_CALIBSCALE),
.event_spec = tsl2772_events,
.num_event_specs = ARRAY_SIZE(tsl2772_events),
},
},
.channel_without_events = {
{
.type = IIO_LIGHT,
.indexed = 1,
.channel = 0,
.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
}, {
.type = IIO_INTENSITY,
.indexed = 1,
.channel = 0,
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
BIT(IIO_CHAN_INFO_INT_TIME) |
BIT(IIO_CHAN_INFO_CALIBSCALE) |
BIT(IIO_CHAN_INFO_CALIBBIAS),
.info_mask_separate_available =
BIT(IIO_CHAN_INFO_INT_TIME) |
BIT(IIO_CHAN_INFO_CALIBSCALE),
}, {
.type = IIO_INTENSITY,
.indexed = 1,
.channel = 1,
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
}, {
.type = IIO_PROXIMITY,
.indexed = 1,
.channel = 0,
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
BIT(IIO_CHAN_INFO_CALIBSCALE),
.info_mask_separate_available =
BIT(IIO_CHAN_INFO_CALIBSCALE),
},
},
.chan_table_elements = 4,
.info = &tsl2772_device_info[ALSPRX2],
},
};
static int tsl2772_probe(struct i2c_client *clientp,
const struct i2c_device_id *id)
{
struct iio_dev *indio_dev;
struct tsl2772_chip *chip;
int ret;
indio_dev = devm_iio_device_alloc(&clientp->dev, sizeof(*chip));
if (!indio_dev)
return -ENOMEM;
chip = iio_priv(indio_dev);
chip->client = clientp;
i2c_set_clientdata(clientp, indio_dev);
chip->supplies[TSL2772_SUPPLY_VDD].supply = "vdd";
chip->supplies[TSL2772_SUPPLY_VDDIO].supply = "vddio";
ret = devm_regulator_bulk_get(&clientp->dev,
ARRAY_SIZE(chip->supplies),
chip->supplies);
if (ret < 0)
return dev_err_probe(&clientp->dev, ret, "Failed to get regulators\n");
ret = regulator_bulk_enable(ARRAY_SIZE(chip->supplies), chip->supplies);
if (ret < 0) {
dev_err(&clientp->dev, "Failed to enable regulators: %d\n",
ret);
return ret;
}
ret = devm_add_action_or_reset(&clientp->dev,
tsl2772_disable_regulators_action,
chip);
if (ret < 0) {
dev_err(&clientp->dev, "Failed to setup regulator cleanup action %d\n",
ret);
return ret;
}
usleep_range(TSL2772_BOOT_MIN_SLEEP_TIME, TSL2772_BOOT_MAX_SLEEP_TIME);
ret = i2c_smbus_read_byte_data(chip->client,
TSL2772_CMD_REG | TSL2772_CHIPID);
if (ret < 0)
return ret;
if (tsl2772_device_id_verif(ret, id->driver_data) <= 0) {
dev_info(&chip->client->dev,
"%s: i2c device found does not match expected id\n",
__func__);
return -EINVAL;
}
ret = i2c_smbus_write_byte(clientp, TSL2772_CMD_REG | TSL2772_CNTRL);
if (ret < 0) {
dev_err(&clientp->dev,
"%s: Failed to write to CMD register: %d\n",
__func__, ret);
return ret;
}
mutex_init(&chip->als_mutex);
mutex_init(&chip->prox_mutex);
chip->tsl2772_chip_status = TSL2772_CHIP_UNKNOWN;
chip->pdata = dev_get_platdata(&clientp->dev);
chip->id = id->driver_data;
chip->chip_info =
&tsl2772_chip_info_tbl[device_channel_config[id->driver_data]];
indio_dev->info = chip->chip_info->info;
indio_dev->modes = INDIO_DIRECT_MODE;
indio_dev->name = chip->client->name;
indio_dev->num_channels = chip->chip_info->chan_table_elements;
if (clientp->irq) {
indio_dev->channels = chip->chip_info->channel_with_events;
ret = devm_request_threaded_irq(&clientp->dev, clientp->irq,
NULL,
&tsl2772_event_handler,
IRQF_TRIGGER_FALLING |
IRQF_ONESHOT,
"TSL2772_event",
indio_dev);
if (ret) {
dev_err(&clientp->dev,
"%s: irq request failed\n", __func__);
return ret;
}
} else {
indio_dev->channels = chip->chip_info->channel_without_events;
}
tsl2772_defaults(chip);
ret = tsl2772_chip_on(indio_dev);
if (ret < 0)
return ret;
ret = devm_add_action_or_reset(&clientp->dev,
tsl2772_chip_off_action,
indio_dev);
if (ret < 0)
return ret;
return devm_iio_device_register(&clientp->dev, indio_dev);
}
static int tsl2772_suspend(struct device *dev)
{
struct iio_dev *indio_dev = dev_get_drvdata(dev);
struct tsl2772_chip *chip = iio_priv(indio_dev);
int ret;
ret = tsl2772_chip_off(indio_dev);
regulator_bulk_disable(ARRAY_SIZE(chip->supplies), chip->supplies);
return ret;
}
static int tsl2772_resume(struct device *dev)
{
struct iio_dev *indio_dev = dev_get_drvdata(dev);
struct tsl2772_chip *chip = iio_priv(indio_dev);
int ret;
ret = regulator_bulk_enable(ARRAY_SIZE(chip->supplies), chip->supplies);
if (ret < 0)
return ret;
usleep_range(TSL2772_BOOT_MIN_SLEEP_TIME, TSL2772_BOOT_MAX_SLEEP_TIME);
return tsl2772_chip_on(indio_dev);
}
static const struct i2c_device_id tsl2772_idtable[] = {
{ "tsl2571", tsl2571 },
{ "tsl2671", tsl2671 },
{ "tmd2671", tmd2671 },
{ "tsl2771", tsl2771 },
{ "tmd2771", tmd2771 },
{ "tsl2572", tsl2572 },
{ "tsl2672", tsl2672 },
{ "tmd2672", tmd2672 },
{ "tsl2772", tsl2772 },
{ "tmd2772", tmd2772 },
{ "apds9930", apds9930},
{}
};
MODULE_DEVICE_TABLE(i2c, tsl2772_idtable);
static const struct of_device_id tsl2772_of_match[] = {
{ .compatible = "amstaos,tsl2571" },
{ .compatible = "amstaos,tsl2671" },
{ .compatible = "amstaos,tmd2671" },
{ .compatible = "amstaos,tsl2771" },
{ .compatible = "amstaos,tmd2771" },
{ .compatible = "amstaos,tsl2572" },
{ .compatible = "amstaos,tsl2672" },
{ .compatible = "amstaos,tmd2672" },
{ .compatible = "amstaos,tsl2772" },
{ .compatible = "amstaos,tmd2772" },
{ .compatible = "avago,apds9930" },
{}
};
MODULE_DEVICE_TABLE(of, tsl2772_of_match);
static const struct dev_pm_ops tsl2772_pm_ops = {
.suspend = tsl2772_suspend,
.resume = tsl2772_resume,
};
static struct i2c_driver tsl2772_driver = {
.driver = {
.name = "tsl2772",
.of_match_table = tsl2772_of_match,
.pm = &tsl2772_pm_ops,
},
.id_table = tsl2772_idtable,
.probe = tsl2772_probe,
};
module_i2c_driver(tsl2772_driver);
MODULE_AUTHOR("J. August Brenner <Jon.Brenner@ams.com>");
MODULE_AUTHOR("Brian Masney <masneyb@onstation.org>");
MODULE_DESCRIPTION("TAOS tsl2772 ambient and proximity light sensor driver");
MODULE_LICENSE("GPL");