Add throttling control via MSR when T-states uses
the FixHW Control Status registers.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Previously _PDC was evaluated later, and thus we'd not get
the chance to tell the BIOS that we can suport FixedHW registers (MSRs)
and the BIOS would always ask us to use System I/O access
for throttling.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
_TSS was erroneously ignored, in favor of the FADT.
When TSS is used, the access width is included in the PTC control/status
register. So it is unnecessary that the access bit width is multiplied by 8.
At the same time the bit_offset should be considered for system I/O Access.
It should be checked the bit_width and bit_offset of PTC regsiter in order to
avoid the failure of system I/O access. It means that bit_width plus
bit_offset can't be greater than 32.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Change the function interface for throttling control via PTC.
The following functions are concerned:
acpi_read_throttling_status()
acpi_write_throttling_state()
acpi_get_throttling_value()
acpi_get_throttling_state()
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Factor out legacy FADT.duty_width code
and run it only in the non _TSS case.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We've run into BIOS that hand us 4-bit access width requests
for T-state control when the code expected only multipls of 8-bits.
Round up.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When a T-state limit change notification is received,
Linux must evaluate _TPC and change its current
T-state immediately to comply with the new limit.
Previously, Linux would notice the new limit
only upon the next throttling change.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This code harks back to the days when we didn't count dirty mapped
pages, which led us to try to balance the number of dirty unmapped pages
by how much unmapped memory there was in the system.
That makes no sense any more, since now the dirty counts include the
mapped pages. Not to mention that the math doesn't work with HIGHMEM
machines anyway, and causes the unmapped_ratio to potentially turn
negative (which we do catch thanks to clamping it at a minimum value,
but I mention that as an indication of how broken the code is).
The code also was written at a time when the default dirty ratio was
much larger, and the unmapped_ratio logic effectively capped that large
dirty ratio a bit. Again, we've since lowered the dirty ratio rather
aggressively, further lessening the point of that code.
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NETFILTER]: Fix NULL pointer dereference in nf_nat_move_storage()
[SUNHME]: VLAN support for sunhme
[CHELSIO]: Fix skb->dev setting.
[NETFILTER]: fix compat_nf_sockopt typo
[INET]: Fix potential kfree on vmalloc-ed area of request_sock_queue
[VIA_VELOCITY]: Don't oops on MTU change.
iwl4965: fix not correctly dealing with hotunplug
rt2x00: Fix chipset revision validation
iwl3945: place CCK rates in front of OFDM for supported rates
mac80211: Fix queuing of scan containing a SSID
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] N32 needs to use the compat version of sys_nfsservctl.
[MIPS] irq_cpu: use handle_percpu_irq handler to avoid dropping interrupts.
[MIPS] Sibyte: Fix name of clocksource.
[MIPS] SNI: s/achknowledge/acknowledge/
[MIPS] Makefile: Fix canonical system names
[MIPS] vpe: handle halting TCs in an errata safe way.
[MIPS] Sibyte: Stop timers before programming next even.
[MIPS] Sibyte: Increase minimum oneshot timer interval to two ticks.
[MIPS] Lasat: Fix overlap of interrupt number ranges.
[MIPS] SNI PCIT CPLUS: workaround for b0rked irq wiring of onboard PCI bus 1
[MIPS] Fix shadow register support.
[MIPS] Change get_cycles to always return 0.
[MIPS] Fix typo in R3000 TRACE_IRQFLAGS code
[MIPS] Sibyte: Replace use of removed IO_SPACE_BASE with IOADDR.
[MIPS] iounmap if in vr41xx_pciu_init() pci clock is over 33MHz
[MIPS] BCM1480: Remove duplicate acknowledge of timer interrupt.
[MIPS] Sibyte: pin timer interrupt to their cores.
[MIPS] Qemu: Add early printk, your friend in a cold night.
[MIPS] Convert reference to mem_map to pfn_to_page().
[MIPS] Sibyte: resurrect old cache hack.
Reported by Chuck Ebbert as:
https://bugzilla.redhat.com/show_bug.cgi?id=259501#c14
This routine is called each time hash should be replaced, nf_conn has
extension list which contains pointers to connection tracking users
(like nat, which is right now the only such user), so when replace takes
place it should copy own extensions. Loop above checks for own
extension, but tries to move higer-layer one, which can lead to above
oops.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables VLAN support on sunhme by increasing BMAC_TXMAX/BMAC_RXMAX
and allocating extra space via skb_put for the VLAN header.
Signed-off-by: Chris Poon <dev-null@telus.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This matters to any sort of device that is wired to one of the CPU
interrupt pins on an SMP system. Typically the scenario is most easily
triggered with the count/compare timer interrupt where the same interrupt
number and thus irq_desc is used on each processor.
CPU A CPU B
do_IRQ()
generic_handle_irq()
handle_level_irq()
spin_lock(desc_lock)
set IRQ_INPROGRESS
spin_unlock(desc_lock)
do_IRQ()
generic_handle_irq()
handle_level_irq()
spin_lock(desc_lock)
IRQ_INPROGRESS set => bail out
spin_lock(desc_lock)
clear IRQ_INPROGRESS
spin_unlock(desc_lock)
In case of the cp0 compare interrupt this means the interrupt will be
acked and not handled or re-armed on CPU b, so there won't be any timer
interrupt until the count register wraps around.
With kernels 2.6.20 ... 2.6.23 we usually were lucky that things were just
working right on VSMP because the count registers are synchronized on
bootup so it takes something that disables interrupts for a long time on
one processor to trigger this one.
For scenarios where an interrupt is multicasted or broadcasted over several
CPUs the existing code was safe and the fix will break it. There is no
way to know in the interrupt controller code because it is abstracted from
the platform code. I think we do not have such a setup currently, so this
should be ok.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The GNU `config.guess' uses "linux-gnu" as the canonical system name.
Fix the list of compiler prefixes checked to spell it correctly.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Adds a JR.HB after halting a TC, to ensure that the TC has really halted.
only modifies the TCSTATUS register when the TC is safely halted.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We have no guarantee by the generic time code that the timer is stopped
when the ->next_event method is called. Modifying the Timer Initial Count
register while the timer is enabled has UNPREDICTABLE effect according to
the BCM1250/BCM1125/BCM1125H User Manual. So stop the timer before
reprogramming.
This is a paranoia fix; no ill effects have been observed previously.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For the old minimum of a single tick a value of zero would be programmed
into the init value register which in the BCM1250/BCM1125/BCM1125H User
Manual in the Timer Special Cases section is documented to have
UNPREDICTABLE effect.
Observable sympthoms of this bug were hangs of several seconds on the
console during bootup and later if both dyntick and highres timer options
were activated.
In theory contiguous mode of the timers is also affected but in an act of
hopeless lack of realism I'll assume nobody will ever configure a KERNEL
for HZ > 500kHz but if so I leave that to evolution to sort out.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The range of MIPS_CPU IRQ and the range of LASAT IRQ overlap.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Shadow register support would not possibly have worked on multicore
systems. The support code for it was also depending not on MIPS R2 but
VSMP or SMTC kernels even though it makes perfect sense with UP kernels.
SR sets are a scarce resource and the expected usage pattern is that
users actually hardcode the register set numbers in their code. So fix
the allocator by ditching it. Move the remaining CPU probe bits into
the generic CPU probe.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This avoids us executing an mfc0 c0_count instruction on processors which
don't have but also on certain R4000 and R4400 versions where reading from
the count register just in the very moment when its value equals
c0_compare will result in the timer interrupt getting lost.
There is still a number of users of get_cycles remaining outside the
arch code:
crypto/tcrypt.c: start = get_cycles();
crypto/tcrypt.c: end = get_cycles();
crypto/tcrypt.c: start = get_cycles();
crypto/tcrypt.c: end = get_cycles();
crypto/tcrypt.c: start = get_cycles();
crypto/tcrypt.c: end = get_cycles();
drivers/char/hangcheck-timer.c: return get_cycles();
drivers/char/hangcheck-timer.c: printk("Hangcheck: Using get_cycles().\n");
drivers/char/random.c: sample.cycles = get_cycles();
drivers/input/joystick/analog.c:#define GET_TIME(x) do { x = get_cycles(); }
include/linux/arcdevice.h: _x = get_cycles(); \
include/linux/arcdevice.h: _y = get_cycles(); \
mm/slub.c: if (!s->defrag_ratio || get_cycles() % 1024 > s->defrag_ratio)
mm/slub.c: p += 64 + (get_cycles() & 0xff) * sizeof(void *);
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
iounmap if pci clock is over 33MHz. Cosmetic because the iomap() in this
case is just a bit of address magic.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The recent switch of the Sibyte SOCs from the processor specific cache
managment code in c-sb1.c to c-r4k.c lost this old hack
[MIPS] Hack for SB1 cache issues
Removing flush_icache_page a while ago broke SB1 which was using an empty
flush_data_cache_page function. This glues things well enough so a more
efficient but also more intrusive solution can be found later.
Signed-Off-By: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
in the hope it was no longer needed. As it turns it still is so resurrect
it until there is a better solution.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
eth_type_trans() now sets skb->dev. Access skb->def after it gets
set.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It should pass opt to the ->get/->set functions, not ops.
Tested-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
cpu_down() code is ok wrt sched_idle_next() placing the 'idle' task not
at the beginning of the queue.
So get rid of activate_idle_task() and make use of activate_task() instead.
It is the same as activate_task(), except for the update_rq_clock(rq) call
that is redundant.
Code size goes down:
text data bss dec hex filename
47853 3934 336 52123 cb9b sched.o.before
47828 3934 336 52098 cb82 sched.o.after
Signed-off-by: Dmitry Adamushko <dmitry.adamushko@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Grant Wilson has reported rare SCHED_FAIR_USER crashes on his quad-core
system, which crashes can only be explained via runqueue corruption.
there is a narrow SMP race in __set_task_cpu(): after ->cpu is set up to
a new value, task_rq_lock(p, ...) can be successfuly executed on another
CPU. We must ensure that updates of per-task data have been completed by
this moment.
this bug has been hiding in the Linux scheduler for an eternity (we never
had any explicit barrier for task->cpu in set_task_cpu() - so the bug was
introduced in 2.5.1), but only became visible via set_task_cfs_rq() being
accidentally put after the task->cpu update. It also probably needs a
sufficiently out-of-order CPU to trigger.
Reported-by: Grant Wilson <grant.wilson@zen.co.uk>
Signed-off-by: Dmitry Adamushko <dmitry.adamushko@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Suppose that the SCHED_FIFO task does
switch_uid(new_user);
Now, p->se.cfs_rq and p->se.parent both point into the old
user_struct->tg because sched_move_task() doesn't call set_task_cfs_rq()
for !fair_sched_class case.
Suppose that old user_struct/task_group is freed/reused, and the task
does
sched_setscheduler(SCHED_NORMAL);
__setscheduler() sets fair_sched_class, but doesn't update
->se.cfs_rq/parent which point to the freed memory.
This means that check_preempt_wakeup() doing
while (!is_same_group(se, pse)) {
se = parent_entity(se);
pse = parent_entity(pse);
}
may OOPS in a similar way if rq->curr or p did something like above.
Perhaps we need something like the patch below, note that
__setscheduler() can't do set_task_cfs_rq().
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently the scheduler checks for PF_VCPU to decide if this timeslice
has to be accounted as guest time. On s390 host interrupts are not
disabled during guest execution. This causes theses interrupts to be
accounted as guest time if CONFIG_VIRT_CPU_ACCOUNTING is set. Solution
is to check if an interrupt triggered account_system_time. As the tick
is timer interrupt based, we have to subtract hardirq_offset.
I tested the patch on s390 with CONFIG_VIRT_CPU_ACCOUNTING and on
x86_64. Seems to work.
CC: Avi Kivity <avi@qumranet.com>
CC: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c/eeprom: Recognize VGN as a valid Sony Vaio name prefix
i2c/eeprom: Hide Sony Vaio serial numbers
i2c-pasemi: Fix NACK detection
i2c-pasemi: Replace obsolete "driverfs" reference with "sysfs"
i2c: Make i2c_check_addr static
i2c-dev: Unbound new-style i2c clients aren't busy
i2c-dev: "how does it work" comments
Recent (i.e. 2005 and later) Sony Vaio laptops have names beginning
with VGN rather than PCG. Update the eeprom driver so that it
recognizes these.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The sysfs interface to DMI data takes care to not make the system
serial number and UUID world-readable, presumably due to privacy
concerns. For consistency, we should not let the eeprom driver
export these same strings to the world on Sony Vaio laptops.
Instead, only make them readable by root, as we already do for BIOS
passwords.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Turns out we don't actually check the status to see if there was a
device out there to talk to, just if we had a timeout when doing so.
Add the proper check, so we don't falsly think there are devices
on the bus that are not there, etc.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
i2c_check_addr is only used inside i2c-core now, so we can make it
static and stop exporting it. Thanks to David Brownell for noticing.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Let i2c-dev deal properly with new-style i2c clients. Instead of
considering them always busy, it needs to check wether a driver is
bound to them or not.
This is still not completely correct, as the client could become
busy later, but the same problem already existed before new-style
clients were introduced. We'll want to fix it someday.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
This adds some "how does this work" comments to the i2c-dev driver,
plus separators between the three main components:
- The parallel list of i2c_adapters ("i2c_dev_list"), each of which
gets a "struct i2c_dev" and a /dev/i2c-X character special file.
- An i2cdev_driver gets adapter add/remove notifications, which are
used to maintain that list of adapters.
- Special file operations, which let userspace talk either directly to
the adapter (for i2c_msg operations) or through cached addressing info
using an anonymous i2c_client (never registered anywhere).
Plus there's the usual module load/unload record keeping.
After making sense of this code, I think that the anonymous i2c_client
is pretty shady. But since it's never registered, using this code with
a system set up for "new style" I2C drivers is no more complicated than
always using the I2C_SLAVE_FORCE ioctl (instead of I2C_SLAVE).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This reverts commit 7fb7ac2411.
Heikki Orsila reports that it causes a regression:
"Doing
nc host port < /dev/zero
on a sending machine (not skge) to an skge machine that is receiving:
nc -l -p port >/dev/null
with ~60 MiB/s speed, causes the interface go malfunct. A slow
transfer doesn't cause a problem."
See
http://bugzilla.kernel.org/show_bug.cgi?id=9321
for some more information.
There is a workaround (also reported by Heikki):
"After some fiddling, I noticed that not changing the register write
order on patch:
+ skge_write32(hw, RB_ADDR(q, RB_END), end);
skge_write32(hw, RB_ADDR(q, RB_WP), start);
skge_write32(hw, RB_ADDR(q, RB_RP), start);
- skge_write32(hw, RB_ADDR(q, RB_END), end);
fixes the visible effect.. Possibly not the root cause of the
problem, but changing the order back fixes networking here."
but that has yet to be ack'ed or tested more widely, so the whole
problem-causing commit gets reverted until this is resolved properly.
Bisected-and-requested-by: Heikki Orsila <shdl@zakalwe.fi>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
