pm_runtime_get_if_in_use() returns -EINVAL if runtime PM is disabled. This
should not be considered an error. Generally the driver has enabled
runtime PM already so getting this error due to runtime PM being disabled
will not happen.
Instead of checking for lesser or equal to zero, check for zero only.
Address this for drivers where this pattern exists.
This patch has been produced using the following command:
$ git grep -l pm_runtime_get_if_in_use -- drivers/media/i2c/ | \
xargs perl -i -pe 's/(pm_runtime_get_if_in_use\(.*\)) \<\= 0/!$1/'
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Replace the calls to pm_runtime_get_noresume() and pm_runtime_put() with
pm_runtime_idle() in the driver's probe function. This will have the same
effect with fewer calls. pm_runtime_disable() in remove is sufficient as
the device is already in RPM_SUSPENDED state.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
An older version of the driver patches were merged accidentally which
resulted in missing the array_size parameter that tells the length of the
array that contains the different supported sizes.
Bring it back to v4l2_find_nearest size and make the corresponding change
for the drivers using it as well.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are some troubles on this driver with respect to the usage
of __be16 and __b32 macros:
drivers/media/i2c/ov5670.c:1857:27: warning: incorrect type in initializer (different base types)
drivers/media/i2c/ov5670.c:1857:27: expected unsigned short [unsigned] [usertype] reg_addr_be
drivers/media/i2c/ov5670.c:1857:27: got restricted __be16 [usertype] <noident>
drivers/media/i2c/ov5670.c:1880:16: warning: cast to restricted __be32
drivers/media/i2c/ov5670.c:1880:16: warning: cast to restricted __be32
drivers/media/i2c/ov5670.c:1880:16: warning: cast to restricted __be32
drivers/media/i2c/ov5670.c:1880:16: warning: cast to restricted __be32
drivers/media/i2c/ov5670.c:1880:16: warning: cast to restricted __be32
drivers/media/i2c/ov5670.c:1880:16: warning: cast to restricted __be32
drivers/media/i2c/ov5670.c:1901:13: warning: incorrect type in assignment (different base types)
drivers/media/i2c/ov5670.c:1901:13: expected unsigned int [unsigned] [usertype] val
drivers/media/i2c/ov5670.c:1901:13: got restricted __be32 [usertype] <noident>
Fix them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use v4l2_find_nearest_size instead of a driver specific function to find
nearest matching size.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Parse async sub-devices related to the sensor by switching the async
sub-device registration function.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Previously, the sensor was not streaming after resume from suspend,
i.e. on S0->S3->S0 transition. Due to this, camera app preview appeared
as stuck.
Now, handle streaming state correctly in case of suspend-resume.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Previously, images were relatively darker due to non-optimal
settings for black target level and bias.
Now, use recommended settings for black target level and output bias
as default values. The same default settings apply to all the resolutions.
Given these recommeneded settings do not change dynamically, add these to
existing mode register settings.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Previously, vblank range given to user was too big, falling outside
of permissible range for a given resolution. Sometimes, too low vblank
resulted in errors.
Now, limit vblank to only permissible range for a given resolution.
This change limits lower-bounds of vblank, doesn't affect upper bounds.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Previously, pixel-rate/(pixels-per-line * lines-per-frame) was
yielding incorrect frame timing for the user.
OV sensor is using internal timing and this requires
conversion (internal timing -> PPL) for correct HBLANK calculation.
Now, change pixels-per-line domain from internal sensor clock to
pixels domain. Set HBLANK read-only because fixed PPL is used for all
resolutions. And, use more accurate link-frequency 422.4MHz instead of
rounding down to 420MHz.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Provides single source pad with up to 2592x1944 pixels at 10-bit raw
bayer format over MIPI CSI2 two lanes at 840Mbps/lane.
The driver supports following features:
- up to 30fps at 5M pixels
- manual exposure
- digital/analog gain
- V-blank/H-blank
- test pattern
- media controller
- runtime pm
[mchehab@s-opensource.com: fix a trivial merge conflict at Makefile]
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
