When not using MSIs, there is no guarantee that DMA from the device
has been fully flushed to point where it's visible to the CPU when
taking an interrupt. To get this guarantee, we need to perform an
MMIO read from the device, which will flush all outstanding DMAs
from bridges between the device and the system.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The writeback ring pointer and IH ring pointer are read using le32_to_cpu
so we do not want the chip to byteswap them on big-endian.
We still want to byteswap the ring itself and the IBs, so we don't touch
that but we remove setting of the byteswap bits in CP_RB_RPTR_ADDR and
IH_CNTL.
In general, for things like that where we control all the accessors easily,
we are better off doing the swap in SW rather than HW. Paradoxally, it does
keep the code closer to x86 and avoid using poorly tested HW features.
I also changed the use of RADEON_ to R600_ in a couple of cases to be more
consistent with the surrounding code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Michel Dänzer <michel@daenzer.net>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just defining rdev->rmmio properly in the first place should do
the trick. In some cases, the cast were also complete dups as
the original variable was already of the right type.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These small changes should allow GEM to be used with non shmem objects as
well as shmem objects. In the GMA500 case it allows the base framebuffer to
appear as a GEM object and thus acquire a handle and work with KMS.
For i915 it ought to be trivial to get back the wasted memory but putting the
system fb back into stolen RAM and in general I can imagine it allowing the
use of GEM and thus KMS with all the older cards that have their framebuffer
firmly placed in video RAM.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Tested-by: Rob Clark <rob@ti.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The video= parameter of the DRM drivers supports some additional flags that
the normal fb drivers do not have. They also allow to limit these flags to
specific outputs. Both things were previously undocumented.
Also the parsing of the line had some oddities:
-A lot of misplaced options were silently ignored or partly rejected instead
of stopping the parsing immediately
-The 'R' option is documented to follow the 'M' option if specified. It is not
documented that 'M' is needed to specify 'R' (also this is the case for normal
fb drivers). In fact the code is correct for normal fb drivers but wrong for
DRM ones.
The old code allowed 'R' only _before_ 'M' (since it parses backwards) and only
if 'M' is given at all which is not needed for the DRM drivers.
-the margins option ('m') was parsed but later ignored even if the later
functions support it.
-specifying multiple enable options at the same time did not lead to an error.
-specifying something bogus for horizontal resolution (i.e. other things as
digits) did not lead to an error but an invalid resolution was used.
If any errors are encountered the position of the faulting string is now
printed to the user and the complete mode is ignored. This gives much
more consistent error behaviour.
I also removed some useless assignments and changed the local flag variables
to be bool.
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
WARNING: drivers/gpu/drm/radeon/radeon.o(.text+0x5d1fc): Section mismatch in reference from the function radeon_get_clock_info() to the function .devinit.text:radeon_read_clocks_OF()
The function radeon_get_clock_info() references
the function __devinit radeon_read_clocks_OF().
This is often because radeon_get_clock_info lacks a __devinit
annotation or the annotation of radeon_read_clocks_OF is wrong.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Also disable the ascii dump and remove the literal printing of the
KERN_ERR macro in the log:
[drm:drm_edid_block_valid] *ERROR* Raw EDID:
<3>00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
v2: Remove the trailing empty line as well.
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/gr: disable fifo access and idle before suspend ctx unload
drm/nouveau: pass flag to engine fini() method on suspend
drm/nouveau: replace nv04_graph_fifo_access() use with direct reg bashing
drm/nv40/gr: rewrite/split context takedown functions
drm/nouveau: detect disabled device in irq handler and return IRQ_NONE
drm/nouveau: ignore connector type when deciding digital/analog on DVI-I
drm/nouveau: Add a quirk for Gigabyte NX86T
drm/nouveau: do not leak in nv20_graph_create
drm/nv50/dp: fix hack to work for macbooks booted via EFI
It may not be necessary to fail in certain cases (such as failing to idle)
on module unload, whereas on suspend it's important to ensure a consistent
state can be restored on resume.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
It's completely pointless to save the PGRAPH context when destroying a
channel, so don't bother.
This commit should also fix kernel.org bug 39422, where the DRM channel
state was incorrectly being saved because we left PGRAPH FIFO access
enabled while running the ctxprog.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
If the connector table is lying, which it often does on the boards of a
particular manufacturer, we may end up doing the wrong thing. Listen
to the encoder table instead, it's more reliable.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The connector table lies, the card has DVI-I not HDMI
Fixes bug https://bugs.freedesktop.org/show_bug.cgi?id=35675
v2: Mention the bugreport
Signed-off-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
If we return due to an unknown chipset in
drivers/gpu/drm/nouveau/nv20_graph.c:nv20_graph_create() we'll leak the
memory allocated to 'pgraph'.
This patch should fix the leak.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Reviewed-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The 3D driver need to get the pipe to backend
map to certain things. Add a query to get the
info.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Include the device id in the bus-id to give userspace a way to open
the correct "cardN" when there are multiple device instances.
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use the fence of the new frontbuffer, if any.
Generating a new fence could cause us to wait for completely unrelated
rendering to finish before performing the flip.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-intel-next' of ssh://master.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6: (52 commits)
drm/i915: provide module parameter description
drm/i915: add module parameter compiler hints
drm/i915/bios: Avoid temporary allocation whilst searching for downclock
drm/i915: Cache GT fifo count for SandyBridge
i915: Fix opregion notifications
drm/i915: TVDAC_STATE_CHG does not indicate successful load-detect
drm/i915: Select correct pipe during TV detect
drm/i915/ringbuffer: Idling requires waiting for the ring to be empty
Revert "drm/i915: enable rc6 by default"
drm/i915: Clean up i915_driver_load failure path
drm/i915: Enable i915 frame buffer compression by default
drm/i915: Share the common work of disabling active FBC before updating
drm/i915: Perform intel_enable_fbc() from a delayed task
drm/i915: Disable FBC across page-flipping
drm/i915: Set persistent-mode for ILK/SNB framebuffer compression
drm/i915: Use of a CPU fence is mandatory to update FBC regions upon CPU writes
drm/i915: Remove vestigial pitch from post-gen2 FBC control routines
drm/i915: Replace direct calls to vfunc.disable_fbc with intel_disable_fbc()
drm/i915: Only export the generic intel_disable_fbc() interface
drm/i915: Enable GPU reset on Ivybridge.
...
Alan Cox reported a missing check on the kmalloc return value for the
allocation of a temporary mode used for searching for the LVDS downlock
frequency. This allocation is roughly 200 bytes, a little too large to
friviously place on the stack. However, we can simply use the few bytes
we need stored within the original DVO timing data, skip the translation
and do the compare directly between the timing data rather than on a
mode, thus avoiding the need for any temporary allocations.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
The read back of the available FIFO entries is vital for system
stability, but extremely costly. However, we only need a guide so as to
avoid eating into the reserved entries and since we are the only
consumer we can cache the read of the count from the last write.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
opregion-based platforms will send ACPI video event 0x80 for a range of
notification types for legacy compatibility. This is interpreted as a
display switch event, which may not be appropriate in the circumstances.
When we receive such an event we should make sure that the platform is
genuinely requesting a display switch before passing that event through
to userspace.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Tested-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Do not use this bit to indicate that load detection has completed,
instead just wait for vblank, at which point the load registers will
have been updated.
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Yi Sun <yi.sun@intel.com>
drm_pci_device_is_pcie duplicates the funcationality of pci_is_pcie.
Convert callers of the former to the latter. This has the side benefit
of removing an unnecessary search in the PCI configuration space due to
using a saved PCIe capability offset.
[airlied: update for new callsite]
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Dave Airlie <airlied@redhat.com>
...which is measured by the size and not the amount of space remaining.
Waiting upon size-8, did one of two things. In the common case with more
than 8 bytes available to write into the ring, it would return
immediately. Otherwise, it would timeout given the impossible condition
of waiting for more space than is available in the ring, leading to
warnings such as:
[drm:intel_cleanup_ring_buffer] *ERROR* failed to quiesce render ring
whilst cleaning up: -16
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
This reverts commit a51f7a66fb.
We still have a few Ironlake and Sandybridge machines which fail when
RC6 is enabled. Better luck next release?
Signed-off-by: Keith Packard <keithp@keithp.com>
i915_driver_load adds a write-combining MTRR region for the GTT
aperture to improve memory speeds through the aperture. If
i915_driver_load fails after this, it would not have cleaned up the
MTRR. This shouldn't cause any problems, except for consuming an MTRR
register. Still, it's best to clean up completely in the failure path,
which is easily done by calling mtrr_del if the mtrr was successfully
allocated.
i915_driver_load calls i915_gem_load which register
i915_gem_inactive_shrink. If i915_driver_load fails after calling
i915_gem_load, the shrinker will be left registered. When called, it
will access freed memory and crash. The fix is to unregister the shrinker in the
failure path using code duplicated from i915_driver_unload.
i915_driver_load also has some incorrect gotos in the error cleanup
paths:
* After failing to initialize the GTT (which cannot happen, btw,
intel_gtt_get returns a fixed (non-NULL) value), it tries to
free the uninitialized WC IO mapping. Fixed this by changing the
target from out_iomapfree to out_rmmap
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Lin Ming <ming.m.lin@intel.com>
That file harkens back to the days of the big 2.4 -> 2.6 version jump,
and was based even then on older versions. Some of it is just obsolete,
and Jesper Juhl points out that it talks about kernel versions 2.6 and
should be updated to 3.0.
Remove some obsolete text, and re-phrase some other to not be 2.6-specific.
Reported-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] msp3400: fill in v4l2_tuner based on vt->type field
[media] tuner-core.c: don't change type field in g_tuner or g_frequency
[media] cx18/ivtv: fix g_tuner support
[media] tuner-core: power up tuner when called with s_power(1)
[media] v4l2-ioctl.c: check for valid tuner type in S_HW_FREQ_SEEK
[media] tuner-core: simplify the standard fixup
[media] tuner-core/v4l2-subdev: document that the type field has to be filled in
[media] v4l2-subdev.h: remove unused s_mode tuner op
[media] feature-removal-schedule: change in how radio device nodes are handled
[media] bttv: fix s_tuner for radio
[media] pvrusb2: fix g/s_tuner support
[media] v4l2-ioctl.c: prefill tuner type for g_frequency and g/s_tuner
[media] tuner-core: fix tuner_resume: use t->mode instead of t->type
[media] tuner-core: fix s_std and s_tuner
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: drop spinlock before calling cifs_put_tlink
cifs: fix expand_dfs_referral
cifs: move bdi_setup_and_register outside of CONFIG_CIFS_DFS_UPCALL
cifs: factor smb_vol allocation out of cifs_setup_volume_info
cifs: have cifs_cleanup_volume_info not take a double pointer
cifs: fix build_unc_path_to_root to account for a prefixpath
cifs: remove bogus call to cifs_cleanup_volume_info
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86:
hp-wmi: fix use after free
dell-laptop - using buffer without mutex_lock
Revert: "dell-laptop: Toggle the unsupported hardware killswitch"
platform-drivers-x86: set backlight type to BACKLIGHT_PLATFORM
thinkpad-acpi: handle HKEY 0x4010, 0x4011 events
drivers/platform/x86: Fix memory leak
thinkpad-acpi: handle some new HKEY 0x60xx events
acer-wmi: fix bitwise bug when set device state
acer-wmi: Only update rfkill status for associated hotkey events
Since we removed sti()/cli() and related, how about removing it from
Documentation/spinlocks.txt?
Signed-off-by: Muthukumar R <muthur@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[ 191.310008] WARNING: kmemcheck: Caught 32-bit read from freed memory (f0d25f14)
[ 191.310011] c056d2f088000000105fd2f00000000050415353040000000000000000000000
[ 191.310020] i i i i f f f f f f f f f f f f f f f f f f f f f f f f f f f f
[ 191.310027] ^
[ 191.310029]
[ 191.310032] Pid: 737, comm: modprobe Not tainted 3.0.0-rc5+ #268 Hewlett-Packard HP Compaq 6005 Pro SFF PC/3047h
[ 191.310036] EIP: 0060:[<f80b3104>] EFLAGS: 00010286 CPU: 0
[ 191.310039] EIP is at hp_wmi_perform_query+0x104/0x150 [hp_wmi]
[ 191.310041] EAX: f0d25601 EBX: f0d25f00 ECX: 000121cf EDX: 000121ce
[ 191.310043] ESI: f0d25f10 EDI: f0f97ea8 EBP: f0f97ec4 ESP: c173f34c
[ 191.310045] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[ 191.310046] CR0: 8005003b CR2: f540c000 CR3: 30f30000 CR4: 000006d0
[ 191.310048] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[ 191.310050] DR6: ffff4ff0 DR7: 00000400
[ 191.310051] [<f80b317b>] hp_wmi_dock_state+0x2b/0x40 [hp_wmi]
[ 191.310054] [<f80b6093>] hp_wmi_init+0x93/0x1a8 [hp_wmi]
[ 191.310057] [<c10011f0>] do_one_initcall+0x30/0x170
[ 191.310061] [<c107ab9f>] sys_init_module+0xef/0x1a60
[ 191.310064] [<c149f998>] sysenter_do_call+0x12/0x28
[ 191.310067] [<ffffffff>] 0xffffffff
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This reverts commit a3d77411e8,
as it causes a mess in the wireless rfkill status on some models.
It is probably a bad idea to toggle the rfkill for all dell models
without the respect to the claim that it is hardware-controlled.
Cc: stable@kernel.org
Signed-off-by: Keng-Yu Lin <kengyu@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
