Johan Hedberg says:
====================
pull request: bluetooth-next 2015-08-28
One more bunch of Bluetooth patches for 4.3:
- Crash fix for hci_bcm driver
- Enhancements to hci_intel driver (e.g. baudrate configuration)
- Fix for SCO link type after multiple connect attempts
- Cleanups & minor fixes in a few other places
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Benc says:
====================
tunnels: fix incorrect IPv4/v6 headers interpretation
With tunneling, it is currently possible to get an IPv6 header and interpret
it as an IPv4 header, or to interpret an IPv6 address as an IPv4 address
(and vice versa). This leads to things like sending packets to incorrect
address, IPv6 flow label being interpreted as IP packet length, etc.
Fix several places where this can happen.
Most of this is net-next only. The third patch affects net, too, but it
doesn't seem there's anything in user space that sets the attribute at all
currently, thus net-next is fine.
Changelog:
v2: fixed geneve after incorrect rebase on top of Pravin's patches
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
By default (subject to the sysctl settings), IPv6 sockets listen also for
IPv4 traffic. Vxlan is not prepared for that and expects IPv6 header in
packets received through an IPv6 socket.
In addition, it's currently not possible to have both IPv4 and IPv6 vxlan
tunnel on the same port (unless bindv6only sysctl is enabled), as it's not
possible to create and bind both IPv4 and IPv6 vxlan interfaces and there's
no way to specify both IPv4 and IPv6 remote/group IP addresses.
Set IPV6_V6ONLY on vxlan sockets to fix both of these issues. This is not
done globally in udp_tunnel, as l2tp and tipc seems to work okay when
receiving IPv4 packets on IPv6 socket and people may rely on this behavior.
The other tunnels (geneve and fou) do not support IPv6.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fou does not really support IPv6 encapsulation. After an UDP socket is
created in fou_create, the encap_rcv callback is set either to fou_udp_recv
or to gue_udp_recv. Both of those unconditionally assume that the received
packet has an IPv4 header and access the data at network_header as it was an
IPv4 header. This leads to IPv6 flow label being interpreted as IP packet
length, etc.
Disallow fou tunnel to be configured as IPv6 until real IPv6 support is
added to fou.
CC: Tom Herbert <tom@herbertland.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's currently nothing preventing directing packets with IPv6
encapsulation data to IPv4 tunnels (and vice versa). If this happens,
IPv6 addresses are incorrectly interpreted as IPv4 ones.
Track whether the given ip_tunnel_key contains IPv4 or IPv6 data. Store this
in ip_tunnel_info. Reject packets at appropriate places if they are supposed
to be encapsulated into an incompatible protocol.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mode field holds a single bit of information only (whether the
ip_tunnel_info struct is for rx or tx). Change the mode field to bit flags.
This allows more mode flags to be added.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few useful tracepoints developing VRF driver.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix build with !CONFIG_NF_CONNTRACK_MARK && CONFIG_OPENVSWITCH_CONNTRACK
Fixes: 182e304 ("openvswitch: Allow matching on conntrack mark")
Reported-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Tested-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next tree.
In sum, patches to address fallout from the previous round plus updates from
the IPVS folks via Simon Horman, they are:
1) Add a new scheduler to IPVS: The weighted overflow scheduling algorithm
directs network connections to the server with the highest weight that is
currently available and overflows to the next when active connections exceed
the node's weight. From Raducu Deaconu.
2) Fix locking ordering in IPVS, always take rtnl_lock in first place. Patch
from Julian Anastasov.
3) Allow to indicate the MTU to the IPVS in-kernel state sync daemon. From
Julian Anastasov.
4) Enhance multicast configuration for the IPVS state sync daemon. Also from
Julian.
5) Resolve sparse warnings in the nf_dup modules.
6) Fix a linking problem when CONFIG_NF_DUP_IPV6 is not set.
7) Add ICMP codes 5 and 6 to IPv6 REJECT target, they are more informative
subsets of code 1. From Andreas Herz.
8) Revert the jumpstack size calculation from mark_source_chains due to chain
depth miscalculations, from Florian Westphal.
9) Calm down more sparse warning around the Netfilter tree, again from Florian
Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
support for '%s' in bpf_trace_printk
v2->v3:
fix the comment to mention that strncpy_from_unsafe() returns
the length of the string including the trailing NUL.
v1->v2:
patch 1: generalize FETCH_FUNC_NAME(memory, string) into
strncpy_from_unsafe()
patch 2: use it in bpf_trace_printk
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
generalize FETCH_FUNC_NAME(memory, string) into
strncpy_from_unsafe() and fix sparse warnings that were
present in original implementation.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure we catch future netpoll_send_udp users who use it without
disabling irqs and also as a hint for poll_controller users.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov says:
====================
Some phylib simplifications
Here's 2 patches against DaveM's 'net-next.git' repo. We simplify a bogus
string of type casts in the 1st patch and make the code respect some coding
standards of the networking code in the 2nd one. I may follow with fixing of
checkpatch.pl's complaints. if I have time..
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix scripts/checkpatch.pl's messages like:
CHECK: Comparison to NULL could be written "!phydrv->read_mmd_indirect"
BTW, it doesn't detect the reversed comparisons (which I've fixed as well).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the bogus string of type casts where ERR_PTR() is enough.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just some minor noise follow-up to address some stylistic issues of
commit 3b3ae88026 ("net: sched: consolidate tc_classify{,_compat}").
Accidentally v1 instead of v2 of that commit got applied, so this
patch adds the relative diff.
Suggested-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, the driver would refuse to load if it couldn't secure
enough VIs from the MC to fulfill its RSS requirements.
This was causing probe to fail on later functions in
configurations where we'd run out of VIs, such as having many
VFs.
This change allows the driver to load with fewer VIs, down to a
minimum of 2. A warning will be printed saying that RSS
requirements were not met, possibly affecting performance.
efx->max_tx_channels needs to be set to avoid going down the
failure path in efx_probe_nic() immediately in the loop after the
probe() NIC-type function.
Also, Set rc=ENOSPC when bombing out of efx_probe_nic due to lack
of VIs.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Forcing uninitialized state allows us to upgrade and reinitialize
the adapter.
FW_VERSION_T4 = 1.4.0.0
FW_VERSION_T5 = 0.0.0.0
FW_VERSION_T6 = 0.0.0.0
At this point driver supports above and greater than above version.
If FW in adapter < min FW_VERSION driver supports tries to upgrade the FW
If FW in adapter >= FW_VERSION driver supports then it follows normal path
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- code beautification
- remove obsolete 'deleted' attribute for bat-gw node
- increase internal version number
- prevent potential access to netdev object after deregistration
- set needed_head/tail_room for batman virtual interface
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=KKXM
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Antonio Quartulli says:
====================
Included changes:
- code beautification
- remove obsolete 'deleted' attribute for bat-gw node
- increase internal version number
- prevent potential access to netdev object after deregistration
- set needed_head/tail_room for batman virtual interface
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix typo in conntrack.c
s/CONFIG_NF_CONNTRACK_LABEL/CONFIG_NF_CONNTRACK_LABELS/
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern says:
====================
net: Refactor inetpeer cache and add support for VRFs
Per Dave's comment on the version 1 patch adding VRF support to inetpeer
cache by explicitly making the address + index a key. Refactored the
inetpeer code in the process; mostly impacts the use by tcp_metrics.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
inetpeer caches based on address only, so duplicate IP addresses within
a namespace return the same cached entry. Enhance the ipv4 address key
to contain both the IPv4 address and VRF device index.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the inetpeer_addr_base union to inetpeer_addr and drop
inetpeer_addr_base.
Both the a6 and in6_addr overlays are not needed; drop the __be32 version
and rename in6 to a6 for consistency with ipv4. Add a new u32 array to
the union which removes the need for the typecast in the compare function
and the use of a consistent arg for both ipv4 and ipv6 addresses which
makes the compare function more readable.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_metrics and inetpeer both have functions to compare inetpeer
addresses. Consolidate into 1 version.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use inetpeer set,get helpers in tcp_metrics rather than peeking into
the inetpeer_addr struct.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactors a common line into helper function.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change to use a custom dst broke tcpdump captures on the VRF device:
$ tcpdump -n -i vrf10
...
05:32:29.009362 IP 10.2.1.254 > 10.2.1.2: ICMP echo request, id 21989, seq 1, length 64
05:32:29.009855 00:00:40:01:8d:36 > 45:00:00:54:d6:6f, ethertype Unknown (0x0a02), length 84:
0x0000: 0102 0a02 01fe 0000 9181 55e5 0001 bd11 ..........U.....
0x0010: da55 0000 0000 bb5d 0700 0000 0000 1011 .U.....]........
0x0020: 1213 1415 1617 1819 1a1b 1c1d 1e1f 2021 ...............!
0x0030: 2223 2425 2627 2829 2a2b 2c2d 2e2f 3031 "#$%&'()*+,-./01
0x0040: 3233 3435 3637 234567
Local packets going through the VRF device are missing an ethernet header.
Fix by adding one and then stripping it off before pushing back to the IP
stack. With this patch you get the expected dumps:
...
05:36:15.713944 IP 10.2.1.254 > 10.2.1.2: ICMP echo request, id 23795, seq 1, length 64
05:36:15.714160 IP 10.2.1.2 > 10.2.1.254: ICMP echo reply, id 23795, seq 1, length 64
...
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The range of addresses between 224.0.0.0 and 224.0.0.255 inclusive, is
reserved for the use of routing protocols and other low-level topology
discovery or maintenance protocols, such as gateway discovery and
group membership reporting. Multicast routers should not forward any
multicast datagram with destination addresses in this range,
regardless of its TTL.
Currently, IGMP reports are generated for this reserved range of
addresses even though a router will ignore this information since it
has no purpose. However, the presence of reserved group addresses in
an IGMP membership report uses up network bandwidth and can also
obscure addresses of interest when inspecting membership reports using
packet inspection or debug messages.
Although the RFCs for the various version of IGMP (e.g.RFC 3376 for
v3) do not specify that the reserved addresses be excluded from
membership reports, it should do no harm in doing so. In particular
there should be no adverse effect in any IGMP snooping functionality
since 224.0.0.x is specifically excluded as per RFC 4541 (IGMP and MLD
Snooping Switches Considerations) section 2.1.2. Data Forwarding
Rules:
2) Packets with a destination IP (DIP) address in the 224.0.0.X
range which are not IGMP must be forwarded on all ports.
IGMP reports for local multicast groups can now be optionally
inhibited by means of a system control variable (by setting the value
to zero) e.g.:
echo 0 > /proc/sys/net/ipv4/igmp_link_local_mcast_reports
To retain backwards compatibility the previous behaviour is retained
by default on system boot or reverted by setting the value back to
non-zero e.g.:
echo 1 > /proc/sys/net/ipv4/igmp_link_local_mcast_reports
Signed-off-by: Philip Downey <pdowney@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The multicast hardware counter on 8168/8111 chips is only 32 bit while the
statistics in struct rtnl_link_stats64 are 64 bit. Given that statistics
are requested on an irregular basis, an overflow of the hardware counter
can go unnoticed. To count even very large numbers of multicast packets
reliably, add a software counter and remove previously applied code to
fill the multicast field requested by @rtl8169_get_stats64 with the values
read from the rx_multicast hardware counter.
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If bcm_suspend is called whithout device opened there is a crash as
it tries to use bdev->hu which is NULL.
Rename bcm_device_list_lock to bcm_device_lock as it does not only apply
to bcm_device_list.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
bridge/netfilter/ebtables.c:290:26: warning: incorrect type in assignment (different modifiers)
-> remove __pure annotation.
ipv6/netfilter/ip6t_SYNPROXY.c:240:27: warning: cast from restricted __be16
-> switch ntohs to htons and vice versa.
netfilter/core.c:391:30: warning: symbol 'nfq_ct_nat_hook' was not declared. Should it be static?
-> delete it, got removed
net/netfilter/nf_synproxy_core.c:221:48: warning: cast to restricted __be32
-> Use __be32 instead of u32.
Tested with objdiff that these changes do not affect generated code.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This reverts commit 98d1bd802c.
mark_source_chains will not re-visit chains, so
*filter
:INPUT ACCEPT [365:25776]
:FORWARD ACCEPT [0:0]
:OUTPUT ACCEPT [217:45832]
:t1 - [0:0]
:t2 - [0:0]
:t3 - [0:0]
:t4 - [0:0]
-A t1 -i lo -j t2
-A t2 -i lo -j t3
-A t3 -i lo -j t4
# -A INPUT -j t4
# -A INPUT -j t3
# -A INPUT -j t2
-A INPUT -j t1
COMMIT
Will compute a chain depth of 2 if the comments are removed.
Revert back to counting the number of chains for the time being.
Reported-by: Cong Wang <cwang@twopensource.com>
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
A platform device can be used to provide some specific resources in
order to manage the controller. In this first patch we retrieve the
reset gpio which is used to power on/off the controller.
The main issue is to match the current tty with the correct pdev.
In case of ACPI, we can easily find the right tty/pdev pair because
they are both child of the same UART port.
If controller is powered-on from the driver, we need to wait for a
HCI boot event before being able to send any command.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The iBT 3.0 controllers need intel/ibt-11-5.sfi and intel/ibt-11-5.ddc
firmware files from linux-firmware repository.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Implement the set_baudrate callback for hci_intel.
- Controller requires a read Intel version command before updating
its baudrate.
- The operation consists in an async cmd since the controller does
not respond at the same speed.
- Wait 100ms to let the controller change its baudrate.
- Clear RTS until we change our own UART speed
Manage speed change in the setup function, we need to restore the oper
speed once chip has booted on patched firmware.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Packets with a variable length value equal to zero were not received.
Since no more data expected (and input buffer entirely consumed), we
need to complete/forward the packet immediately instead of waiting for
more data.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
So far we handled boolean input by forcing them with !! and assigning
them into a bool. This allowed userspace to send values > 1 which were
used as 1. We should be stricter here and return -EINVAL for all but
0 or 1.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This makes the function sco_conn_del have a return type of void now
due to this function always running successfully and thus never
needing to signal its caller when a non recoverable internal failure
occurs by returning a error code to its respective caller.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change ensures we will get driver name as 'btmrvl_sdio'
in udev event.
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
- Fix MSI/MSI-X on pseries from Guilherme
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qDdb
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Fix MSI/MSI-X on pseries from Guilherme"
* tag 'powerpc-4.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/PCI: Disable MSI/MSI-X interrupts at PCI probe time in OF case
PCI: Make pci_msi_setup_pci_dev() non-static for use by arch code
Pull networking fixes from David Miller:
"Some straggler bug fixes here:
1) Netlink_sendmsg() doesn't check iterator type properly in mmap
case, from Ken-ichirou MATSUZAWA.
2) Don't sleep in atomic context in bcmgenet driver, from Florian
Fainelli.
3) The pfkey_broadcast() code patch can't actually ever use anything
other than GFP_ATOMIC. And the cases that right now pass
GFP_KERNEL or similar will currently trigger an RCU splat. Just
use GFP_ATOMIC unconditionally. From David Ahern.
4) Fix FD bit timings handling in pcan_usb driver, from Marc
Kleine-Budde.
5) Cache dst leaked in ip6_gre tunnel removal, fix from Huaibin Wang.
6) Traversal into drivers/net/ethernet/renesas should be triggered by
CONFIG_NET_VENDOR_RENESAS, not a particular driver's config
option. From Kazuya Mizuguchi.
7) Fix regression in handling of igmp_join errors in vxlan, from
Marcelo Ricardo Leitner.
8) Make phy_{read,write}_mmd_indirect() properly take the mdio_lock
mutex when programming the registers. From Russell King.
9) Fix non-forced handling in u32_destroy(), from WANG Cong.
10) Test the EVENT_NO_RUNTIME_PM flag before it is cleared in
usbnet_stop(), from Eugene Shatokhin.
11) In sfc driver, don't fetch statistics firmware isn't capable of,
from Bert Kenward.
12) Verify ASCONF address parameter location in SCTP, from Xin Long"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
sctp: donot reset the overall_error_count in SHUTDOWN_RECEIVE state
sctp: asconf's process should verify address parameter is in the beginning
sfc: only use vadaptor stats if firmware is capable
net: phy: fixed: propagate fixed link values to struct
usbnet: Get EVENT_NO_RUNTIME_PM bit before it is cleared
drivers: net: xgene: fix: Oops in linkwatch_fire_event
cls_u32: complete the check for non-forced case in u32_destroy()
net: fec: use reinit_completion() in mdio accessor functions
net: phy: add locking to phy_read_mmd_indirect()/phy_write_mmd_indirect()
vxlan: re-ignore EADDRINUSE from igmp_join
net: compile renesas directory if NET_VENDOR_RENESAS is configured
ip6_gre: release cached dst on tunnel removal
phylib: Make PHYs children of their MDIO bus, not the bus' parent.
can: pcan_usb: don't provide CAN FD bittimings by non-FD adapters
net: Fix RCU splat in af_key
net: bcmgenet: fix uncleaned dma flags
net: bcmgenet: Avoid sleeping in bcmgenet_timeout
netlink: mmap: fix tx type check
Pull nvdimm fixlet from Dan Williams:
"This is a libnvdimm ABI fixup.
I pushed back on this change quite hard given the late date, that it
appears to be purely cosmetic, sysfs is not necessarily meant to be a
user friendly UI, and the kernel interprets the reversed polarity of
the ACPI_NFIT_MEM_ARMED flag correctly. When this flag is set, the
energy source of an NVDIMM is not armed and any new writes to the DIMM
may not be preserved.
However, Bob Moore warned me that it is important to get these things
named correctly wherever they appear otherwise we run the risk of a
less than cautious firmware engineer implementing the polarity the
wrong way. Once a mistake like that escapes into production platforms
the flag becomes useless and we need to move to a new bit position.
Bob has agreed to take a change through ACPICA to rename
ACPI_NFIT_MEM_ARMED to ACPI_NFIT_MEM_NOT_ARMED, and the patch below
from Toshi brings the sysfs representation of these flags in line with
their respective polarities.
Please pull for 4.2 as this is the first kernel to expose the ACPI
NFIT sysfs representation, and this is likely a kernel that firmware
developers will be using for checking out their NVDIMM enabling"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit: Clarify memory device state flags strings
Phil Sutter says:
====================
fixup IFF_NO_QUEUE conversion
This series serves two purposes:
On one hand it fixes a quite embarrassing bug around the warning I added for
drivers still setting tx_queue_len = 0 to achieve noqueue operation. It turned
out to be quite useless as due to using alloc_netdev(), many in-kernel drivers
fell into the trap by accident, as well. Instead this place serves pretty well
as a sanitizing point to set IFF_NO_QUEUE for drivers not initializing
tx_queue_len, which in turn allows to drop all special treatment of the latter
being zero since that can not happen anymore without IFF_NO_QUEUE being set.
On the other hand, it provides a better solution for Eric Dumazet's concern
regarding how to assign noqueue to an interface which does not default to it
already. In order to make this possible, noqueue is being registered so users
can 'tc qd add dev eth0 root noqueue'. In addition, it resolves the ugly
situation of 'tc qd show' not showing noqueue. Finally, the former changes
allow for some code cleanup.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that noqueue qdisc can be attached just like any other qdisc, no
special treatment is necessary anymore when attaching it as default
qdisc.
This change has the added benefit that 'tc qdisc show' prints noqueue
instead of nothing for devices defaulting to noqueue.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
This way users can attach noqueue just like any other qdisc using tc
without having to mess with tx_queue_len first.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
