This patch (as961) fixes a couple of bugs in the disconnect pathway of
usb-storage.
The first problem, which apparently has been around for a while
although nobody noticed it, shows up when an aborted command is still
pending when a disconnect occurs. The SCSI error-handler will
continue to wait in command_abort() until the us->notify completion is
signalled. Thus quiesce_and_remove_host() needs to signal it.
The second problem was introduced recently along with autosuspend
support. Since usb_stor_scan_thread() now calls
usb_autopm_put_interface() before exiting, we can't simply leave the
scanning thread running after a disconnect; we must wait until the
thread exits. This is solved by adding a new struct completion to the
private data structure. Fortuitously, it allows the removal of the
rather clunky mechanism used in the past to insure that all threads
have finished before the module is unloaded.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some devices have a bug which causes them to send a 1-byte reply to
Get-Device-Status requests instead of 2 bytes as required by the
spec. This doesn't play well with autosuspend, since we look for a
valid status reply to make sure the device is still present when it
resumes. Without both bytes, we assume the device has been
disconnected.
Lack of the second byte shouldn't matter much, since the spec requires
it always to be equal to 0. Hence this patch (as959) causes
finish_port_resume() to accept a 1-byte reply as valid.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The oti6858 usb serial driver should use kernel_termios_to_user_termios/
user_termios_to_kernel_termios to avoid segfaults because the kernel
uses a structure differing from that of user space with a different
size.
Signed-off-by: Thomas Viehmann <tv@beamnet.de>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as958) removes an unneeded and unwanted #define line from
dummy_hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If, in em28xx_usb_probe() the memory allocation
dev->alt_max_pkt_size = kmalloc(32*
dev->num_alt,GFP_KERNEL);
fails, then we'll bail out and return -ENOMEM.
The problem is that in that case we don't free the storage allocated
to 'dev', thus causing a memory leak.
This patch fixes the leak by freeing 'dev' before we return -ENOMEM.
This fixes Coverity bug #647.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The attached (mostly trivial) patches adds support for the Evolution
Scorpion Robots.
Evolution Robotics supplies a patch against 2.6.8 with their
software. My patch is based on their work, so I don't know if I can
sign it off, or if you need some Evolution people to do this (which
might be hard).
The patch adds device ID's for some robots which is trivial.
From: Søren Hauberg <hauberg@gmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Søren
It appears that one reason the "iConnect"-labeled multi-card reader was
on sale for only $5 is that it doesn't handle suspend/resume correctly.
Other than that, it was a good deal for a highspeed MMC/SD bridge.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently when registration fails we're left with a stray reference to
release_mem_region(), this leads to the following case:
r8a66597_hcd r8a66597_hcd: irq 13, io base 0x18040000
drivers/usb/host/r8a66597-hcd.c: register access fail.
r8a66597_hcd r8a66597_hcd: startup error -6
r8a66597_hcd r8a66597_hcd: USB bus 1 deregistered
drivers/usb/host/r8a66597-hcd.c: Failed to add hcd
Trying to free nonexistent resource <0000000018040000-0000000018040000>
This fixes it up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Previous boards were likely seeing USB_ARCH_HAS_HCD selected by way
of PCMCIA or PCI, though none of those are required for hcd support
on SH. Enable support unconditionally.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dell Wireless Broadband ExpressCards are rebrands of Novatel's cards.
Add all of their known PCI IDs to date along with their mapping to the exact
Novatel model to the Option driver which already claims to support them.
Signed-off-by: Faidon Liambotis <paravoid@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I noticed this warning with CONFING_PM=n
...
drivers/usb/host/u132-hcd.c:1525: warning: 'port_power' defined but not used
...
Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix typo in safe_serial.c to match the actual CONFIG variable.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the File Storage Gadget stall the control endpoint
when a MSC class request is made with wValue != 0. This change makes
some MSC compliance test warnings disappear.
Signed-off-by: Luis Lloret <luislloret@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch contains two fixes submitted by Ondrej Palkovsky:
- the 'ACK' packet is sent after the transfer of the USB packet is
completed, i.e. in the write_callback function. Because the close
function sends the 'abort' command, a parameter is added that allows
the caller of garmin_write_bulk to specify, if the 'ack' should be
propagated to the serial link or dimissed.
This fixes the problem with gpsbabel, it has sent several packets that
were acknowledged before they were sent to the GPS and GpsBabel closed
the device - thus effectively cancelled all outstanding requests in the
queue.
- removed the APP_RESP_SEEN and APP_REQ_SEEN flags and changed
them into counters. It evades USB reset of the gps on every device close.
Signed-off-by: Hermann Kneissel <hermann.kneissel@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as950) fixes a bug in the cdc-acm driver. It doesn't keep
track of which interface (control or data) the sysfs attributes get
registered for, and as a result, during disconnect it will sometimes
attempt to remove the attributes from the wrong interface. The
left-over attributes can cause a crash later on, particularly if the driver
module has been unloaded.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
git commit b2bbb20b37 added direct
support for PXA GPIO D+ pullup as alternative to the older udc_command
ops method. This was done by introduction of the pxa2xx_udc_mach_info
member "gpio_pullup" which, if initialized, is now used in (almost)
all places where udc_command used to be called.
This patch fixes two places where checks for availability of D+ pullup
control still only honor udc_command.
Signed-off-by: Uli Luckas <u.luckas@road.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] Add support for 1533 bridge to alim1535_wdt
[WATCHDOG] Add a 00-INDEX file to Documentation/watchdog/
[WATCHDOG] Eurotechwdt.c - clean-up comments
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[IRDA] irda_nl_get_mode: always results in failure
[PPP]: Fix output buffer size in ppp_decompress_frame().
[IRDA]: Avoid a label defined but not used warning in irda_init()
[IPV6]: Fix kernel panic while send SCTP data with IP fragments
[SNAP]: Check packet length before reading
[DCCP]: Allocation in atomic context
When a vmur device is removed due to a detach of the device, currently the
ur device structure is freed. Unfortunately it can happen, that there is
still a user of the device structure, when the character device is open
during the detach process. To fix this, reference counting for the vmur
structure is introduced.
In addition to that, the online, offline, probe and remove functions are
serialized now using a global mutex.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
There are several s390 diagnose calls, which must be executed below the
2GB memory boundary. In order to enforce this, those diagnoses must be
compiled into the kernel. Currently diag 14 can be called within the
vmur kernel module from addresses above 2GB. This leads to specification
exceptions. This patch moves diag10, diag14 and diag210 into the new
diag.c file.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Hipersocket Multicast queue works asynchronously. When sending buffers,
the buffer state change may happen delayed. The tasklet for checking
changes in the outbound queue excluded IQDIO async queues from this
process. This created either a hang situation when the queue ran full,
or presented a hang situation a interface close time.
The tasklet processing is changed to include IQDIO async queues when
requesting buffer state refresh.
Signed-off-by: Klaus D. Wacker <kdwacker@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
QDIO returned from EQBS instruction in any case after return code
CCQ=96 was issued regardless whether buffer states for at least one
buffer were extracted or not.
This caused FCP devices to hang when running under z/VM and having
QIOASSASIST=ON and having high I/O rates.
In order to fix this qdio return code processing of EQBS instruction
after CCQ=96 is changed that buffers are returned and if no buffers
where extracted the instruction is repeated at once.
Signed-off-by: Klaus D. Wacker <kdwacker@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
cmf currently prints a message that more than 4096 channels are not
allowed in basic mode - however, this can only be enforced if cmf was
a module (which is no longer possible). It makes much more sense to
not check the specified number of channels and just print a message if
the block for basic mode could not be allocated (which may happen for
any number of specified channels).
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch addresses the issue with "osize too small" errors in mppe
encryption. The patch fixes the issue with wrong output buffer size
being passed to ppp decompression routine.
--------------------
As pointed out by Suresh Mahalingam, the issue addressed by
ppp-fix-osize-too-small-errors-when-decoding patch is not fully resolved yet.
The size of allocated output buffer is correct, however it size passed to
ppp->rcomp->decompress in ppp_generic.c if wrong. The patch fixes that.
--------------------
Signed-off-by: Konstantin Sharlaimov <konstantin.sharlaimov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are special PHY settings available on Yukon EC-U chip that
should not get cleared. This should solve mysterious errors on some
motherboards (like Gigabyte DS-3).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes handling of USB ISO completion error -EXDEV and includes
several other changes to current CVS version at isdn4linux.de (changes
in debug flags, style of code remarks, etc)
Signed-off-by: Martin Bachem <info@colognechip.com>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 196705c9bb. It was
reported to cause a regression by Daniel Exner, and Arjan van de Ven
points out that we actually already have infrastructure in place for
setting limits on acceptable DMA latency that would be the much more
correct fix for the problem with some Broadcom EHCI controllers.
Fixed up trivial conflicts due to the changes to support big-endian host
controller descriptors in drivers/usb/host/{ehci-sched.c,ehci.h}.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
V4L/DVB (6028): Turn an unnecessary mdelay() into msleep().
V4L/DVB (6027): Get rid of an ill-behaved msleep in i2c write
V4L/DVB (6026): Avoid powering up the camera on resume
V4L/DVB (6016): get_dvb_firmware: update script for new location of tda10046 firmware
V4L/DVB (5991): dvb-pll: Set minimum and maximum frequency properly
V4L/DVB (5969): ivtv: report ivtv version in status log
V4L/DVB (5967): ivtv: fix VIDIOC_S_FBUF:new OSD values where never set
V4L/DVB (5968): videodev2.h: remove superfluous FBUF GLOBAL_INV_ALPHA support
This disk reports total number of sectors instead of maximum sector address
in response to READ_NATIVE_MAX_ADDRESS command and also happily accepts
SET_MAX_ADDRESS command with the bogus value. This results in +1 sector
capacity being used and errors on attempts to use the last sector.
...
hdd: Host Protected Area detected.
    current capacity is 78165360 sectors (40020 MB)
    native  capacity is 78165361 sectors (40020 MB)
hdd: Host Protected Area disabled.
...
hdd: reading: block=78165360, sectors=1, buffer=0xc1e63000
hdd: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdd: dma_intr: error=0x10 { SectorIdNotFound }, LBAsect=78165360, sector=78165360
...
Add hpa_list[] table and workaround the issue in idedisk_check_hpa().
v2:
* Add missing export and improve patch description a bit.
v3:
* Add list termination. (From Mikko)
Fixes kernel bugzilla bug #8816.
Thanks to Mikko for investigating the issue and helping with this patch.
Cc: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Programming DMA mode may destroy current PIO mode setting so if
CONFIG_HPT34X_AUTODMA=n (the default case) make ide_tune_dma() fail
early by disabling all host DMA masks and re-tune PIO mode.
This fix doesn't help with the driver being broken but is needed
for some other changes.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks
shouldn't be initialized or bad things will happen.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks
shouldn't be initialized or bad things will happen.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks
shouldn't be initialized or bad things will happen.
Also this host driver requires valid PCI BAR4 for normal operation so
check it in ->init_chipset and fail initialization if not set.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks
shouldn't be initialized or bad things will happen.
Also this host driver requires valid PCI BAR4 for normal operation so
check it in ->init_chipset and fail initialization if not set.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use ->OUTBSYNC instead of ->OUTB when writing command register
(needed for scc_pata and pmac host drivers).
* Don't check DRDY bit of the status register on ATAPI devices
(ATAPI devices are free to ignore DRDY bit).
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Cc: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move ide_in_drive_list() from ide-dma.c to ide-iops.c.
* Add ivb_list[] table for listening early UDMA66 devices which don't conform
to ATA4 standard wrt cable detection (bit14 is zero, only bit13 is valid)
and use only device side cable detection for them since host side cable
detection may be unreliable.
* Add model "QUANTUM FIREBALLlct10 05" with firwmare "A03.0900" to the list
(from Craig's bugreport).
v2:
* Improve kernel message basing on suggestion from Sergei.
v3:
* Don't print kernel message when no device side cable detection is done,
plus some minor fixes. (Noticed by Sergei)
Thanks to Craig for testing this patch.
Cc: Craig Block <chblock3@yahoo.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
pmac_ide_tune_chipset() don't set drive->init_speed.
Fix it by setting drive->{current,init}_speed in pmac_ide_do_setfeature()
and clean up pmac_ide_{tune_chipset,mdma_enable,udma_enable}().
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add DMA blacklist checking (->ide_dma_on check probably can go now).
* Add ->atapi_dma flag checking and remove no longer needed
ns87415_ide_dma_check() from ns87415 host driver.
* Remove now needless __ide_dma_check() wrapper and symbol export.
* Check drive->autodma instead of hwif->autodma (there should be no changes in
behavior as all users of config_drive_for_dma() set both ->autodma flags).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Some host drivers depend on CONFIG_IDE_GENERIC to do the probing but their
config options lack explicit dependencies on IDE_GENERIC. In the long-term
these host drivers should be fixed to do the probing themselves but for now
fix them by making their config options select CONFIG_IDE_GENERIC.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
These days, CONFIG_IDE_GENERIC causes more confusion and
misconfiguration than it helps. Especially so because libata is
linked after the generic driver. Default to N.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: "P.C.Chan" <pc.chan@alcatel-lucent.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Configuring the OLPC camera requires something over 150 register
writes. Unfortunately, querying the CAFE i2c controller too
soon after a write causes the hardware to flake. The problem had
been "solved" with an msleep() call, but, between the number of
registers and how msleep() behaves, that resulted in a 3-second
delay on camera initialization. Instead, we hand-code a wait for
the completion interrupt which avoids reading the status registers.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The tuner maximum frequency wasn't being set, while the minimum
frequency was set to what the maximum should have been.
If a future patch were to enforce these limits, dvb-pll would be
effectively broken.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
ivtv: fix VIDIOC_S_FBUF support: new OSD values where never actually set.
The values set with VIDIOC_S_FBUF were not actually used until the next
VIDIOC_S_FMT. Fixed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When taking a cpu down, we need to hardware_disable() it.
Unfortunately, the CPU_DYING notifier is called with interrupts
disabled, which means we can't use smp_call_function_single().
Fortunately, the CPU_DYING notifier is always called on the dying cpu,
so we don't need to use the function at all and can simply call
hardware_disable() directly.
Tested-by: Paolo Ornati <ornati@fastwebnet.it>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the forcedeth driver receives too much work in an interrupt, it
assumes it has a broken hardware with stuck IRQ. It works around the
problem by disabling interrupts on the nic but makes a printk while
holding device spinlog - which isn't smart thing to do if you have
netconsole on the same nic.
This patch moves the printk's out of the spinlock protected area.
Without this patch the machine hangs hard. With this patch everything
still works even when there is significant increase on CPU usage while
using the nic.
Signed-off-by: Timo Jantunen <jeti@iki.fi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The lguest block device only requests one minor, which means
partitions don't work (eg "root=/dev/lgba1").
Let's follow the crowd and ask for 16.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Incorrect semicolon after if statement
mlx4_core: Wait 1 second after reset before accessing device
IPoIB: Fix leak in ipoib_transport_dev_init() error path
IB/mlx4: Fix opcode returned in RDMA read completion
IB/srp: Add OUI for new Cisco targets
IB/srp: Wrap OUI checking for workarounds in helper functions
RDMA/cxgb3: Always call low level send function via cxgb3_ofld_send()
IB: Move the macro IB_UMEM_MAX_PAGE_CHUNK() to umem.c
IB: Include <linux/list.h> and <linux/rwsem.h> from <rdma/ib_verbs.h>
IB: Include <linux/list.h> from <rdma/ib_mad.h>
IB/mad: Fix address handle leak in mad_rmpp
IB/mad: agent_send_response() should be void
IB/mad: Fix memory leak in switch handling in ib_mad_recv_done_handler()
IB/mad: Fix error path if response alloc fails in ib_mad_recv_done_handler()
IB/sa: Don't need to check for default P_Key twice
IB/core: Ignore membership bit in ib_find_pkey()
From: Andrey Borzenkov <arvidjaar@mail.ru>
They are apparently pretty close (even lspci combines them). The patch
adds support for 0x1533 bridge in addition to 0x1535.
Tested on Toshiba Portege 4000 with
00:07.0 ISA bridge [0601]: ALi Corporation M1533/M1535 PCI to ISA Bridge
[Aladdin IV/V/V+] [10b9:1533]
00:08.0 Bridge [0680]: ALi Corporation M7101 Power Management Controller
[PMU] [10b9:7101]
with result
[ 2090.906736] PCI: Enabling device 0000:00:08.0 (0000 -> 0001)
[ 2090.914034] ALi_M1535: initialized. timeout=3D60 sec (nowayout=3D0)
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Clean-up history and add a comment about the fact that
the watchdog is actually part of the SMSC FDC 37B782
super I/O chipset.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
A stray semicolon makes us inadvertently ignore the value of err.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Adjust libata to ignore errors after spinup
This patch is to ignore errors from the spinup attempt if the drive is
in the "standby id" state.
Signed-off-by: Ryan Power <rpower@sysreset.com>
Acked-by: Mark Lord <liml@rtr.ca>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add TECRA M7 to broken suspend list. Reported by Marie Koreen.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Marie Koreen <kbug@koreen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix several inconsistencies in these drivers WRT reporting the clocks:
- when using DPLL mode, 'pata_hpt37x' driver reported the DPLL frequency as the
PCI clock -- make it properly report both clocks and add the same ability to
the 'pata_hpt3x2n' driver;
- both drivers sometimes use "pata_hpt3*:" and sometimes "hpt3*:" in the
messages -- make them use only the former one;
- the message about failed DPLL stablizatios deserves KERN_ERR and a bang. :-)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The DPLL tuning code always set up it for 66 MHz due to wrong UltraDMA mask
including mode 5 used to check for the necessity of 66 MHz clocking -- this
caused 66 MHz clock to be used for HPT374 chip that does not tolerate it.
While fixing this, also remove PLL mode from the TODO list -- I don't think
it's still a relevant item.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Maximum supported UDMA mode for AEC6280[R] is UDMA5 (not UDMA4)
and for AEC6880[R] it is UDMA6 (not UDMA5):
* Fix the problem by adding missing struct ata_port_info to artop_init_one().
* Use the right naming (s/626/628/).
* Bump driver version.
Fixes IDE->libata regression, problem was never present in IDE aec62xx driver.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Underneath all the HPT packaging, PCI identifiers, binary driver modules
and stuff you find that ...
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This reverts commit 3bd92ba19a.
It is no longer necessary, and it opens up a race.
Acked-by: Vladimir Lebedev <vladimir.p.lebedev@gmail.com>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Some hardware will malfunction at a temperature below
the BIOS provided critical shutdown threshold.
This hook allows moving the critical trip points down
to a temperature which provokes a graceful shutdown
before the hardware malfunction.
http://bugzilla.kernel.org/show_bug.cgi?id=8884
WARNING: A trip-point override will not get noticed
until the system delivers a temperature change event,
or unless thermal zone polling is enabled.
eg. "thermal.tzp=10"
Signed-off-by: Len Brown <len.brown@intel.com>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c-s3c2410: Build fix
i2c/menelaus: Build fix
i2c-mv64xxx: Reinitialize hw and driver on I2C bus hang
i2c-mpc: Don't disable I2C module on stop condition
i2c-iop3xx: Set I2C_CLASS_HWMON to adapter class
i2c/isp1301_omap: Build fixes, whitespace
i2c-mpc: Pass correct dev_id to free_irq on error path
i2c-i801: Typo: erroneous
Fixup the include files after the arch moves that
where included in 2.6.23.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Under certain conditions, the mv64xxx I2C bus can hang preventing
further operation. To make the driver more robust, we now reset
the I2C hardware and the driver state machine when such hangs are
detected.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Disabling module on stop doesn't work on some CPUs (ie. mpc8241,
as reported by Guennadi Liakhovetski), so remove that.
Disable I2C module on errors/interrupts to prevent it from
locking up on mpc5200b.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
In order to be able to use sensors on the IOP3xx SoCs, one needs to set
the adapter class to I2C_CLASS_HWMON.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Build fixes for isp1301_omap driver. I think an earlier version
of this must have gotten lost somewhere, or maybe it only went
into the Linux-OMAP tree.
Also, some whitespace fixes to bring this more into sync with the
version of this found in the Linux-OMAP tree. (That version has
updates for the OTG controller on the OMAP 1710 which break that
functionality on OMAP 161x boards like the H2, so merging all of
it is not currently an option.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[IPVS]: Use IP_VS_WAIT_WHILE when encessary.
[NET]: Share correct feature code between bridging and bonding
[ATM] drivers/atm/iphase.c: mostly kmalloc + memset conversion to kzalloc
[IRDA] irda-usb.c: mostly kmalloc + memset conversion to k[cz]alloc
[WAN] drivers/net/wan/hdlc_fr.c: kmalloc + memset conversion to kzalloc
[DCCP]: fix memory leak and clean up style - dccp_feat_empty_confirm()
[DCCP]: fix theoretical ccids_{read,write}_lock() race
[XFRM]: Clean up duplicate includes in net/xfrm/
[TIPC]: Clean up duplicate includes in net/tipc/
[SUNRPC]: Clean up duplicate includes in net/sunrpc/
[PKT_SCHED]: Clean up duplicate includes in net/sched/
[IPV6]: Clean up duplicate includes in net/ipv6/
[IPV4]: Clean up duplicate includes in net/ipv4/
[ATM]: Clean up duplicate includes in net/atm/
[ATM]: Clean up duplicate includes in drivers/atm/
[IPCONFIG]: ip_auto_config fix
[ATM]: fore200e_param_bs_queue() must be __devinit
This patch adds support for 2 new board variants:
- A Quad port fiber 82571 board
- A blade version of the 82571 quad copper board
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
http://bugzilla.kernel.org/show_bug.cgi?id=8797 shows that the
bonding driver may produce bogus combinations of the checksum
flags and SG/TSO.
For example, if you bond devices with NETIF_F_HW_CSUM and
NETIF_F_IP_CSUM you'll end up with a bonding device that
has neither flag set. If both have TSO then this produces
an illegal combination.
The bridge device on the other hand has the correct code to
deal with this.
In fact, the same code can be used for both. So this patch
moves that logic into net/core/dev.c and uses it for both
bonding and bridging.
In the process I've made small adjustments such as only
setting GSO_ROBUST if at least one constituent device
supports it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up duplicate includes in
drivers/atm/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
WARNING: drivers/built-in.o(.text+0x6203bb): Section mismatch: reference to .init.text:fore200e_param_bs_queue (between 'fore200e_initialize' and 'fore200e_monitor_putc')
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
xennet_tx_bug_gc can free the skb before we use it, so make sure we don't.
Signed-off-by: Keir Fraser <keir@xensource.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A special sequence of ifconfig up/down and plug/unplug the cable can break
the duplex configuration of the driver.
Setting
vp->mii.full_duplex = vp->full_duplex
in vortex_up should fix this.
Addresses Bug 8575 3c59x duplex configuration broken
http://bugzilla.kernel.org/show_bug.cgi?id=8575
Cc: Martin Buck <mb-tmp-ohtmvyyn.xreary.bet@gromit.dyndns.org>
Signed-off-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Cc: Natalie Protasevich <protasnb@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When a detailed netdev error is counted, we also must account for it in the
aggregated error count.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=8106
Cc: Tim Hockin <thockin@hockin.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Chongfeng Hu <loveminix@yahoo.com.cn>
Cc: Natalie Protasevich <protasnb@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/net/ax88796.c: In function `ax_probe':
drivers/net/ax88796.c:825: warning: size_t format, different type arg (arg 4)
drivers/net/ax88796.c:825: warning: size_t format, different type arg (arg 5)
resource_size_t isn't size_t.
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the pause counter to avoid a needless device reset, and
print a message telling the admin that our link partner is
flow controlling us down to 0 pkts/sec.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patch to disable the rx_copybreak feature on hardware architectures that
don't allow unaligned DMA access.
#ifdef code taken from tulip_core.c. Problem pointed out by Ivan
Kokshaysky.
Signed-off-by: Dustin Marquess <jailbird@alcatraz.fdf.net>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Put a 1000 msec delay after resetting the device before attempting to
do config cycles on it. Not waiting causes system hangs on some
chipsets, e.g. Intel E7520, when the driver is loaded.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The smsc47m1 driver no longer creates the name attribute used by
libsensors to identify chip types. It was lost during the conversion
to a platform driver. I was fooled by the fact that we do have a
group with all attributes, but only to delete them all at once. The
group is not used to create the attributes, so we have to explicitly
create the name attribute.
This fixes lm-sensors ticket #2236:
http://lm-sensors.org/ticket/2236
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Don't assume that the default bank is 0. For one thing, we don't even
set it to 0 when the driver is loaded, so the initial state might be
different. For another, something (say, the BIOS) might access the chip
and leave with the bank set to something different, so assuming that
the bank value is 0 is not safe.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch forces the driver to read the fan divider values during early init.
Otherwise, a call to store_fan_min() could access uninitialized variables.
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use DMI to:
1. enable polling (BIOS thermal events are broken)
2. disable active trip points (BIOS fan control is broken)
3. disable passive trip point (BIOS hard-codes it too low)
The actual temperature reading does work,
and with the aid of polling, the critical
trip point should work too.
http://bugzilla.kernel.org/show_bug.cgi?id=8842
Signed-off-by: Len Brown <len.brown@intel.com>
thermal.act=-1 disables all active trip points
in all ACPI thermal zones.
thermal.act=C, where C > 0, overrides all lowest temperature
active trip points in all thermal zones to C degrees Celsius.
Raising this trip-point may allow you to keep your system silent
up to a higher temperature. However, it will not allow you to
raise the lowest temperature trip point above the next higher
trip point (if there is one). Lowering this trip point may
kick in the fan sooner.
Note that overriding this trip-point will disable any BIOS attempts
to implement hysteresis around the lowest temperature trip point.
This may result in the fan starting and stopping frequently
if temperature frequently crosses C.
WARNING: raising trip points above the manufacturer's defaults
may cause the system to run at higher temperature and shorten
its life.
Signed-off-by: Len Brown <len.brown@intel.com>
thermal.nocrt=1 disables actions on _CRT and _HOT
ACPI thermal zone trip-points. They will be marked
as <disabled> in /proc/acpi/thermal_zone/*/trip_points.
There are two cases where this option is used:
1. Debugging a hot system crossing valid trip point.
If your system fan is spinning at full speed,
be sure that the vent is not clogged with dust.
Many laptops have very fine thermal fins that are easily blocked.
Check that the processor fan-sink is properly seated,
has the proper thermal grease, and is really spinning.
Check for fan related options in BIOS SETUP.
Sometimes there is a performance vs quiet option.
Defaults are generally the most conservative.
If your fan is not spinning, yet /proc/acpi/fan/
has files in it, please file a Linux/ACPI bug.
WARNING: you risk shortening the lifetime of your
hardware if you use this parameter on a hot system.
Note that this refers to all system components,
including the disk drive.
2. Working around a cool system crossing critical
trip point due to erroneous temperature reading.
Try again with CONFIG_HWMON=n
There is known potential for conflict between the
the hwmon sub-system and the ACPI BIOS.
If this fixes it, notify lm-sensors@lm-sensors.org
and linux-acpi@vger.kernel.org
Otherwise, file a Linux/ACPI bug, or notify
just linux-acpi@vger.kernel.org.
Signed-off-by: Len Brown <len.brown@intel.com>
"thermal.psv=-1" disables passive trip points
for all ACPI thermal zones.
"thermal.psv=C", where 'C' is degrees Celsius,
overrides all existing passive trip points
for all ACPI thermal zones.
thermal.psv is checked at module load time,
and in response to trip-point change events.
Note that if the system does not deliver thermal zone
temperature change events near the new trip-point,
then it will not be noticed. To force your custom
trip point to be noticed, you may need to enable polling:
eg. thermal.tzp=3000 invokes polling every 5 minutes.
Note that once passive thermal throttling is invoked,
it has its own internal Thermal Sampling Period (_TSP),
that is unrelated to _TZP.
WARNING: disabling or raising a thermal trip point
may result in increased running temperature and
shorter hardware lifetime on some systems.
Signed-off-by: Len Brown <len.brown@intel.com>
Thermal Zone Polling frequency (_TZP) is an optional ACPI object
recommending the rate that the OS should poll the associated thermal zone.
If _TZP is 0, no polling should be used.
If _TZP is non-zero, then the platform recommends that
the OS poll the thermal zone at the specified rate.
The minimum period is 30 seconds.
The maximum period is 5 minutes.
(note _TZP and thermal.tzp units are in deci-seconds,
so _TZP = 300 corresponds to 30 seconds)
If _TZP is not present, ACPI 3.0b recommends that the
thermal zone be polled at an "OS provided default frequency".
However, common industry practice is:
1. The BIOS never specifies any _TZP
2. High volume OS's from this century never poll any thermal zones
Ie. The OS depends on the platform's ability to
provoke thermal events when necessary, and
the "OS provided default frequency" is "never":-)
There is a proposal that ACPI 4.0 be updated to reflect
common industry practice -- ie. no _TZP, no polling.
The Linux kernel already follows this practice --
thermal zones are not polled unless _TZP is present and non-zero.
But thermal zone polling is useful as a workaround for systems
which have ACPI thermal control, but have an issue preventing
thermal events. Indeed, some Linux distributions still
set a non-zero thermal polling frequency for this reason.
But rather than ask the user to write a polling frequency
into all the /proc/acpi/thermal_zone/*/polling_frequency
files, here we simply document and expose the already
existing module parameter to do the same at system level,
to simplify debugging those broken platforms.
Note that thermal.tzp is a module-load time parameter only.
Signed-off-by: Len Brown <len.brown@intel.com>
"thermal.off=1" disables all ACPI thermal support at boot time.
CONFIG_ACPI_THERMAL=n can do this at build time.
"# rmmod thermal" can do this at run time,
as long as thermal is built as a module.
WARNING: On some systems, disabling ACPI thermal support
will cause the system to run hotter and reduce the
lifetime of the hardware.
Signed-off-by: Len Brown <len.brown@intel.com>
Make the needlessly global "acpi_event_seqnum" static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Send key=value pair along with the uevent instead of a plain value so that
userspace (udev) can handle it like common environment variables.
Signed-off-by: Holger Macht <hmacht@suse.de>
Acked-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Stephan Berberig <s.berberig@arcor.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
There must not be a new-line character in the uevent. Otherwise, udev gets
confused. Thanks to Kay Sievers for pointing it out.
Signed-off-by: Stephan Berberig <s.berberig@arcor.de>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] monwriter: Serialization bug for multithreaded applications.
[S390] vmur: diag14 only works with buffers below 2GB
[S390] vmur: add "top of queue" sanity check for reader open
[S390] vmur: reject open on z/VM reader files with status HOLD
[S390] vmur: use DECLARE_COMPLETION_ONSTACK to keep lockdep happy
[S390] vmur: allocate single record buffers instead of one big data buffer
[S390] remove DEFAULT_MIGRATION_COST
[S390] qdio: make sure data structures are correctly aligned.
[S390] hypfs: implement show_options
[S390] cio: avoid memory leak on error in css_alloc_subchannel().
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
BLOCK: Hide the contents of linux/bio.h if CONFIG_BLOCK=n
sysace: HDIO_GETGEO has it's own method for ages
drivers/block/cpqarray.c: better error handling and kmalloc + memset conversion to k[cz]alloc
drivers/block/cciss.c: kmalloc + memset conversion to kzalloc
Clean up duplicate includes in drivers/block/
Fix remap handling by blktrace
[PATCH] remove mm/filemap.c:file_send_actor()
Fix following section mismatch warning:
WARNING: drivers/built-in.o(.text+0x73d0): Section mismatch: reference to .init.data: (between 'pxafb_setup' and 'pxafb_init')
The warning are caused by __devinit pxafb_setup() that refers to a
variable marked __initdata. In a hotplug scenario we would have a
reference to the freed .init.data section. Fix this by declaring
g_options __devinitdata.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 19d36ccdc3 "x86: Fix alternatives
and kprobes to remap write-protected kernel text" uses code which is
being patched for patching.
In particular, paravirt_ops does patching in two stages: first it
calls paravirt_ops.patch, then it fills any remaining instructions
with nop_out(). nop_out calls text_poke() which calls
lookup_address() which calls pgd_val() (aka paravirt_ops.pgd_val):
that call site is one of the places we patch.
If we always do patching as one single call to text_poke(), we only
need make sure we're not patching the memcpy in text_poke itself.
This means the prototype to paravirt_ops.patch needs to change, to
marshal the new code into a buffer rather than patching in place as it
does now. It also means all patching goes through text_poke(), which
is known to be safe (apply_alternatives is also changed to make a
single patch).
AK: fix compilation on x86-64 (bad rusty!)
AK: fix boot on x86-64 (sigh)
AK: merged with other patches
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Files using bits from paravirt.h should explicitly include it rather than
relying on it being pulled in by something else.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gcc-4.2 is a lot more picky about its symbol handling. EXPORT_SYMBOL no
longer works on symbols that are undefined or defined with static scope.
For example, with CONFIG_PROFILE off, I see:
kernel/profile.c:206: error: __ksymtab_profile_event_unregister causes a section type conflict
kernel/profile.c:205: error: __ksymtab_profile_event_register causes a section type conflict
This patch moves the EXPORTs inside the #ifdef CONFIG_PROFILE, so we
only try to export symbols that are defined.
Also, in kernel/kprobes.c there's an EXPORT_SYMBOL_GPL() for
jprobes_return, which if CONFIG_JPROBES is undefined is a static
inline and gives the same error.
And in drivers/acpi/resources/rsxface.c, there's an
ACPI_EXPORT_SYMBOPL() for a static symbol. If it's static, it's not
accessible from outside the compilation unit, so should bot be exported.
These three changes allow building a zx1_defconfig kernel with gcc 4.2
on IA64.
[akpm@linux-foundation.org: export jpobe_return properly]
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Git rid of "warning: passing arg 2 of `access_ok' makes pointer from integer
without a cast" reported on SH ... most architectures use macros in that
test, SH uses inlined functions.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sh:
drivers/mtd/mtdchar.c: In function `mtd_mmap':
drivers/mtd/mtdchar.c:817: error: dereferencing pointer to incomplete type
drivers/mtd/mtdchar.c:817: error: `VM_SHARED' undeclared (first use in this function)
drivers/mtd/mtdchar.c:817: error: (Each undeclared identifier is reported only once
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch c5c34d4862 (tty: flush flip buffer on
ldisc input queue flush) introduces a race condition which can lead to memory
leaks.
The problem can be triggered when tcflush() is called when data are being
pushed to the line discipline driver by flush_to_ldisc().
flush_to_ldisc() releases tty->buf.lock when calling the line discipline
receive_buf function. At that poing tty_buffer_flush() kicks in and sets both
tty->buf.head and tty->buf.tail to NULL. When flush_to_ldisc() finishes, it
restores tty->buf.head but doesn't touch tty->buf.tail. This corrups the
buffer queue, and the next call to tty_buffer_request_room() will allocate a
new buffer and overwrite tty->buf.head. The previous buffer is then lost
forever without being released.
(Thanks to Laurent for the above text, for finding, disgnosing and reporting
the bug)
- Use tty->flags bits for the flush status.
- Wait for the flag to clear again before returning
- Fix the doc error noted
- Fix flush of empty queue leaving stale flushpending
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Paul Fulghum <paulkf@microgate.com>
Cc: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Long ago I've noticed (but didn't pay much attention) that
spi_mpc83xx using PM calculations that differs from what
specs describe. I.e.
u8 pm = mpc83xx_spi->spibrg / (spi->max_speed_hz * 4);
While specs says: "The SPI baud rate generator clock source (either
system clock or system clock divided by 16, depending on DIV16 bit) is
divided by 4 * ([PM] + 1), a range from 4 to 64.".
Thus " - 1" is missing in the spi_mpc83xx's formula.
Why nobody noticed that bug? Probably because sysclk usually less then
user expects, e.g. you expect 200 MHz, but real clock is 198 MHz,
and integer rounding helps when this formula is used.
Suppose it's SPI in QE, SYSCLK at 198 MHz, thus SPIBRG at 99MHz, 25 MHz
requested.
PM = (99MHz / ( 25 MHz * 4 )), PM == 0, output SPICLK will be 24.75 MHz
At lower frequencies this bug is more noticeable, though.
And this bug shows itself in all its beauty if SYSCLK is equal or a bit
more than you expect (200 MHz SYSCLK, 100 MHz SPIBRG):
PM = (100MHz / ( 25 MHz * 4 )), PM == 1, output SPICLK will be 12.625 MHz!
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For MPC8349E input to the SPI Baud Rate Generator is SYSCLK, but it's
SYSCLK/2 for MPC8323E (SPI in QE). Fix this, and remove confusion by
renaming the mpc83xx_spi->sysclk member as mpc83xx_spi->spibrg.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cm4000_cs.c and cm4040_cs.c call the internal release function with
an argument of wrong type. this fixes bug #8485
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Bill McConnaughey <mcconnau@biochem.wustl.edu>
Cc: Natalie Protasevich <protasnb@gmail.com>
Cc: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This builds upon my previous attempts to resolve some jitter problems seen
with the Matrox G450 and G550 -based cards, including odd disparities observed
between x86 and Power -based machines in a somewhat less hackish way (removing
the hacked ifdefs).
Apparently, preference should be given to use the DVI PLL when frequencies
permit, the Standard PLL otherwise. The max pixel clock for the panellink
interface is extracted from the PInS information on the card and used as a
limit to determine which PLL to use.
Signed-off-by: Paul A. Clarke <pc@us.ibm.com>
Acked-by: Petr Vandrovec <petr@vandrovec.name>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- better handling of the pvr2 registers based on more up to date information.
Testing shows that it seems to work pretty well at 16bpp, 24bpp and 32bpp -
including proper rendering of the boot logo at all levels (previously this was
a bit broken even at 16bpp) and giving white against black text. Really
detailed testing (eg with X11) requires support for the maple bus - which
isn't (currently - next project assuming this is okay) available, but I have
no reason to think this is broken.
Signed-off by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported by: Adrian McMenamin <adrianmcmenamin@gmail.com>
This driver will oops when the pseudo_palette[] is written as u32 but not when
written as u16. When written as u32, it corrupts the adjacent 'mmio_base'
field of struct pvr2fb_par. Fix by using framebuffer_alloc()/release() to
allocate struct fb_info and struct pvr2fb_par, and create the pseudo_palette[]
as part of struct pvr2fb_par.
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix compile warning ('map_override unused') if fbcon is compiled as a module
and CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=n.
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Visualize-EG, Graffiti and A4450A graphics cards on PARISC can
be configured in double-buffer and standard mode, but the stifb
driver supports standard mode only.
This patch detects double-buffered cards more reliable.
It is a real bugfix for a very nasty problem for all parisc users which have
wrongly configured their graphic card. The problem: The stifb graphics driver
will not detect that the card is wrongly configured and then nevertheless just
enables the graphics mode, which it shouldn't. In the end, the user will see
no further updates / boot messages on the screen.
We had documented this problem already on our FAQ
(http://parisc-linux.org/faq/index.html#viseg "Why do I get corrupted graphics
with my Vis-EG/Graffiti/A4450A card?") but people still run into this problem.
So having this fix in as early as possible can help us.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Cc: <stable@kernel.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The way this driver tries to implement HDIO_GETGEO it'll never be called.
Then again on ppc it probably will never be called anyway because it's
utterly pointless.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch removes some redundant casts, does the kmalloc + memset to
k[cz]alloc conversion and it changes the error path to use goto (to avoid code
duplication).
drivers/block/cpqarray.c | 49567 -> 48623 (-944 bytes)
drivers/block/cpqarray.o | 178820 -> 178288 (-532 bytes)
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch cleans up duplicate includes in
drivers/block/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Satyam Sharma <satyam.sharma@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch provides more information concerning REMAP operations on block
IOs. The additional information provides clearer details at the user level,
and supports post-processing analysis in btt.
o Adds in partition remaps on the same device.
o Fixed up the remap information in DM to be in the right order
o Sent up mapped-from and mapped-to device information
Signed-off-by: Alan D. Brunelle <alan.brunelle@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Commit 348753379a introduced a regression that
caused temp2 and temp3 sensor type settings to be written to temp1 instead.
The result is that temp sensor readings could be way off.
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Locking added so that multithreaded applications can now do writes
from different threads without the risk of storage corruption.
Signed-off-by: Melissa Howland <melissah@us.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If memory buffers above 2GB are used, diagnose 14 raises a specification
exception. This fix ensures that buffer allocation is done below the 2GB
boundary.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the z/VM reader is already open, it can happen that after opening the
Linux reader device, not the topmost file is processed. According the
semantics of the Linux z/VM unit record device driver, always the topmost
file has to be processed. With this fix an error is returned if that is
not the case.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If a reader file with HOLD status is at the top of the reader queue, currently
all read requests will return data of the second file in the queue. But the
semantics of vmur is that always the topmost file is read. With this fix
-EPERM is returned on open, if the topmost reader file is in HOLD status.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
vmur allocates one contiguous kernel buffer to copy user data when creating
ccw programs for punch or printer. If big block sizes are used, under memory
pressure it can happen, that we do not get memory in one chunk. Now we
allocate memory for each single record to avoid high order allocations.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The slsb structure contained at the beginning of the qdio_q structure
must start on a 256 byte boundary. To make sure this is the case even
if slab debugging is turned on create an own slab cache for qdio_q
structures.
Besides that don't use the slab allocator to allocate whole pages. Use
the page allocator instead.
Also fix a few memory leaks in error handling code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
sch->lock has been allocated in cio_validate_subchannel(), it must be
freed if cio_modify() fails.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
mmc: at91_mci: remove whitespace at the end of lines
mmc: reorganize bounce buffer init
wbsd: fix section mismatch warnings
If a Guest makes hypercall which sets a GDT entry to not present, we
currently set any segment registers using that GDT entry to 0.
Unfortunately, this is not sufficient: there are other ways of
altering GDT entries which will cause a fault.
The correct solution to do what Linux does: let them set any GDT value
they want and handle the #GP when popping causes a fault. This has
the added benefit of making our Switcher slightly more robust in the
case of any other bugs which cause it to fault.
We kill the Guest if it causes a fault in the Switcher: it's the
Guest's responsibility to make sure it's not using segments when it
changes them.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
lguest uses a host-supplied wallclock-based clocksource when the TSC
is not reliable. As this is already in nanoseconds, I naively used a
multiplier of 1 and a shift of 0.
But update_wall_time() in its infinite wisdom decides to adjust the
clock a little (where does it think it's getting a more accurate time
from?)
It will happily tweak the multiplier... to 0, then -1.
So the "fix" is to use a shift of 22 like everyone else, and a
multiplier of 1 << 22.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some cleanup with whitespace/tab at the end of lines.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Reorganize the code that initializes mmc_block's bounce buffer in
order to avoid warnings when MMC_BLOCK_BOUNCE isn't used.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch fixes the following section mismatch warnings
...
WARNING: vmlinux.o(.init.text+0x29d40): Section mismatch: reference to .exit.text:wbsd_release_resources (between 'wbsd_init' and 'wbsd_probe')
WARNING: vmlinux.o(.init.text+0x29d49): Section mismatch: reference to .exit.text:wbsd_free_mmc (between 'wbsd_init' and 'wbsd_probe')
WARNING: vmlinux.o(.init.text+0x29f28): Section mismatch: reference to .exit.text:wbsd_free_mmc (between 'wbsd_init' and 'wbsd_probe')
...
Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch addresses some issues in x86/x86-64 acpi-cpufreq driver:
1. Current memory allocation for acpi_perf_data is actually open-coded
alloc_percpu(). The patch defines and handles acpi_perf_data as percpu
data. The code will be cleaner and easier to be maintained with this
change.
2. Won't load driver in acpi_cpufreq_early_init() failure case.
3. Add __init for acpi_cpufreq_early_init().
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
> >> Looks like memset() is zeroing wrong nr of bytes.
> >
> > Good catch, however, I think we can just remove this memset altogether
> > since the memory gets allocated via kzalloc.
>
> Correct, that memset() is superfluous.
Ok. Then this should do it.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
drivers/net/ibmveth.c | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use shorter method to determine whether adapter has configured ports
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sis190 driver assumes to find ISA only on SiS965.
similar fix is in sis900 driver, see bug report
http://bugs.debian.org/435547
Signed-off-by: maximilian attems <max@stro.at>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
use the simpler spin_trylock_irqsave() API to get the adapter lock.
[ this is also a fix for -rt where adapter->lock is a sleeping lock. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
SH boards in general only wire this up in 8 or 16-bit mode, and
as we never had the wrappers for 32-bit mode defined, SMC_CAN_USE_32BIT
caused build failure for the non-Solution Engine boards. This gets it
building again.
Also kill off the straggling set_irq_type() definition, this is left
over cruft that was missed when the rest of it switched to IRQ flags.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
--
drivers/net/smc91x.h | 4 +---
1 file changed, 1 insertion(+), 3 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ipoib_transport_dev_init() calls ipoib_cm_dev_init(), so it needs to
call ipoib_cm_dev_cleanup() to unwind that on the error path.
Found by Dotan Barak of Mellanox.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Enable C3 without bm control only for CST based C3.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The current kconfig help text was misleading users. Also, the default for
an input-layer-optimized support caused way too many problems without
up-to-date userspace in place.
So, rework the help text, and change the default to N. Note that
distributions are supposed to enable this option as soon as they update HAL
to a version that handles the thinkpad-acpi new input layer interface.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Lguest drivers need to default to "Y" otherwise they're never selected
for new builds. (We don't bother prompting, because they're less than
4k combined, and implied by selecting lguest support).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
More fallout from the writeback fixes: debug register transfer
instructions do their own writeback and thus need to disable the general
writeback mechanism.
This fixes oopses and some guest failures on AMD machines (the Intel
variant decodes the instruction in hardware and thus does not need
emulation).
Cc: Alistair John Strachan <alistair@devzero.co.uk>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NETFILTER]: Add xt_statistic.h to the header list for usermode programs
[BNX2]: Fix suspend/resume problem.
[TG3]: Fix suspend/resume problem.
This 965G and above chipsets moved the batch buffer non-secure bits to
another place. This means that previous drm's allowed in-secure batchbuffers
to be submitted to the hardware from non-privileged users who are logged
into X and and have access to direct rendering.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Theory : though needless, it should not have hurt.
Practice: it does not play nice with DEBUG_SHIRQ + LOCKDEP + UP
(see https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=242572).
The patch makes sense in itself but I should dig why it has an effect
on #242572 (assuming that NAPI do not change in a near future).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Fix extracted from Realtek's driver (8.002.00/20070713) for the PHY
attached to 8111/8168b chipsets.
The check against mac_version is just usual paranoia during the bugfix
period of the kernel cycle. -- FR
Tested on Asus M2A-VM motherboard by Roger So.
No regression on my Asrock 945G DVI either (built-in 8168 + 2x8169).
Signed-off-by: Roger So <roger.so@gmail.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
While filling the control set the driver tests for a PSPOLL frame.
But it tested only the subtype of the packet. The full type needs
to be tested to identify those packets reliably.
[dsd@gentoo.org: backport to mainline]
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
conf->mac_addr is not guaranteed to be set. This ensures priv->hwaddr is
always set to a valid mac address. Thanks to Johannes Berg
<johannes@sipsolutions.net> for finding this problem.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 77548f5807.
David Woodhouse wrote:
>This broke my shinybook. I seem to get absolutely _no_ outgoing packets,
>although I can receive OK.
Larry Finger wrote:
>Please revert this patch.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alan Cox suggested that the solution to the FIXMEs in pata_icside is
to use a private postreset method to detect the lack of devices on a
port, and in such a case, disable the interrupt for the port.
This patch implements such a method, and removes the hard coded
disable of port 0. Tested as working.
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
(This is a resend of a patch originally submitted on 24-Jul-2007 00:14)
Ok, this is something the coverity checker found (CID: 1813).
I'm not at all intimate with this code, so I'm not sure if this
attempt at a fix is correct (but at least it compiles).
Please look it over and NACK if bad or merge if good ;-)
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
If the driver fails to allocate the contiguous (DMAable) memory for
system reasons, we fail to load the instance, but then we try to free
the <nul> allocation in the cleanup code and we get a panic in
pci_free_consistent(). This is reported against an older kernel, hope
this is relevant for latest/greatest.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
And finally this is the regular !use_sg cleanup
and use of data accessors.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
check_condition code-path was similar but more
complicated to Reset. It went like this:
1. extra space was allocated at aha152x_scdata for mirroring
scsi_cmnd members.
2. At aha152x_internal_queue() every not check_condition
(REQUEST_SENSE) command was copied to above members in
case of error.
3. At busfree_run() in the DONE_CS phase if a Status of
SAM_STAT_CHECK_CONDITION was detected. The command was
re-queued Internally using aha152x_internal_queue(,,check_condition,)
The old command members are over written with the
REQUEST_SENSE info.
4. At busfree_run() in the DONE_CS phase again. If it is a
check_condition command, info was restored from mirror
made at first call to aha152x_internal_queue() (see 2)
and the command is completed.
What I did is:
1. Allocate less space in aha152x_scdata only for the 16-byte
original command. (which is actually not needed by scsi-ml
anymore at this stage. But this is to much knowledge of scsi-ml)
2. If Status == SAM_STAT_CHECK_CONDITION, then like before
re-queue a REQUEST_SENSE command. But only now save original
command members. (Less of them)
3. In aha152x_internal_queue(), just like for Reset, use the
check_condition hint to set differently the working members.
execute the command.
4. At busfree_run() in the DONE_CS phase again. restore needed
members.
While at it. This patch fixes a BUG. Old code when sending
a REQUEST_SENSE for a failed command. Would than return with
cmd->resid == 0 which was the status of the REQUEST_SENSE.
The failing command resid was lost. And when would resid
be interesting if not on a failing command?
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
What Reset code was doing: Save command's important/dangerous
Info on stack. NULL those members from scsi_cmnd.
Issue a Reset. wait for it to finish than restore members
and return.
What I do is save or NULL nothing. But use the "resetting"
hint in aha152x_internal_queue() to NULL out working members
and leave struct scsi_cmnd alone.
The indent here looks funny but it will change/drop in last
patch and it is clear this way what changed.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
hunk by hunk:
- CHECK_CONDITION is what happens to cmnd->status >> 1
or after status_byte() macro. But here it is used
directly on status which means 0x1 which is an undefined
bit in the standard. And is a status that will never
return from a target.
- in busfree_run at the DONE_SC phase we have 3 distinct
operation:
1-if(DONE_SC->SCp.phase & check_condition)
The REQUEST_SENSE command return.
- Restore original command
- Than continue to operation 3.
2-if(DONE_SC->SCp.Status==SAM_STAT_CHECK_CONDITION)
A regular command returned with a status.
- Internally re-Q a REQUEST_SENSE.
- Do not do operation 3.
3-
- Complete the command and return it to scsi-ml
So the 0x2 in both these operations (1,2) means the scsi
check-condition status, hence SAM_STAT_CHECK_CONDITION
- Here the code asks about !(DONE_SC->SCp.Status & not_issued)
but "not_issued" is an enum belonging to the "phase" member
and not to the Status returned from target. The reason this
works is because not_issued==1 and Also CHECK_CONDITION==1
(remember from hunk 1). So actually the code was asking
!(DONE_SC->SCp.Status & CHECK_CONDITION). Which means
"Has the status been read from target yet?"
Staus is read at status_run(). "not_issued" is
cleared in seldo_run() which is usually earlier than
status_run().
So this patch does nothing as far as assembly is concerned
but it does let the reader understand what is going on.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cause highmem buffers to be bounced to low memory until this
driver supports highmem addresses. Otherwise it just oopses
on NULL buffer addresses.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The symbol <debug_locks> conflicts with the rather global one in
include/linux/locks.h.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Our current implementation has a generic set of barrier functions that
go through the SCSI driver model. Realistically, this is unnecessary,
because the only device that can use barriers (sd) can set the flush
functions up at probe or revalidate time. This patch pulls the barrier
functions out of the mid layer and scsi driver model and relocates them
directly in sd.
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The device would not resume properly if it was shutdown before the system
was suspended. In such scenario where the netif_running state is 0,
bnx2_suspend() would not save the PCI state and so the memory enable bit
and bus master enable bit would be lost.
We fix this by always saving and restoring the PCI state in
bnx2_suspend() and bnx2_resume() regardless of netif_running() state.
Update version to 1.6.4.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joachim Deguara <joachim.deguara@amd.com> reported that tg3 devices
would not resume properly if the device was shutdown before the system
was suspended. In such scenario where the netif_running state is 0,
tg3_suspend() would not save the PCI state and so the memory enable bit
and bus master enable bit would be lost.
We fix this by always saving and restoring the PCI state in
tg3_suspend() and tg3_resume() regardless of netif_running() state.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove dead code spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch fixes an obvious use-after-free introduced by
commit 837012ede1.
Spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
* wrong argument passed to pci_unmap_single() on failure
exit paths
* leak in the same area
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
the early setup function serial8250_console_early_setup() can be called
from non __init code (eg. hotpluggable serial ports like serial_cs) so
remove the __init from the call chain to avoid crashes.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some ASUS laptops fail to use boot time EC
and need to eventually switch to one described in DSDT.
http://bugzilla.kernel.org/show_bug.cgi?id=8709
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Some ASUS laptops access EC space from device _INI methods, but do not
provide ECDT for early EC setup. In order to make them function properly,
there is a need to find EC is DSDT before any _INI is called.
Similar functionality was turned on by acpi_fake_ecdt=1 command line
before. Now it is on all the time.
http://bugzilla.kernel.org/show_bug.cgi?id=8598
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Current code has a cut-and-paste error and returns IB_WC_SEND when it
should return IB_WC_RDMA_READ.
Signed-off-by: Vu Pham <vu@mellanox.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ACPI: EC: Handler for query 0x57 is not found!
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch fixes memory size detection on the CG6 card.
The 1MB TGX card has dblbuf property set to 0.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Renninger reports that if one tries to load thinkpad-acpi in a
non-thinkpad, one gets:
Call Trace:
[<ffffffff802fa57d>] kref_get+0x2f/0x36
[<ffffffff802f97f7>] kobject_get+0x12/0x17
[<ffffffff8036dfd7>] get_driver+0x14/0x1a
[<ffffffff8036dfee>] driver_remove_file+0x11/0x32
[<ffffffff8823b9be>] :thinkpad_acpi:thinkpad_acpi_module_exit+0xa8/0xfc
[<ffffffff8824b8a0>] :thinkpad_acpi:thinkpad_acpi_module_init+0x74a/0x776
[<ffffffff8024f968>] __link_module+0x0/0x25
[<ffffffff80252269>] sys_init_module+0x162c/0x178f
[<ffffffff8020bc2e>] system_call+0x7e/0x83
So, track if the platform driver and its driver attributes were registered,
and only deallocate them in that case.
This patch is based on Thomas Renninger's patch for the issue.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
ids member of struct acpi_driver is of type struct acpi_device_id, not a
character array.
Signed-off-by: Eugene Teo <eugeneteo@kernel.sg>
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Len Brown <len.brown@intel.com>
New Cisco IB SRP targets use the Cisco OUI 00-1b-0d but still need the
Topspin workarounds. Add this OUI to srp_target_is_topspin().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Wrap the checking for Mellanox and Topspin OUIs to decide whether to
use a workaround into helper functions. This will make it cleaner to
add a new OUI to check (as we need to do now that some targets with a
Cisco OUI still need the Topspin workarounds).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
After moving the definition of struct ib_umem_chunk from ib_verbs.h to
ib_umem.h there isn't any reason for the macro IB_UMEM_MAX_PAGE_CHUNK
to stay in ib_verbs.h. Move the macro to umem.c, the only place where
it is used.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The address handle associated with dual-sided RMPP direction switch
ACKs is never destroyed. Free the AH for ACKs which fall into this
category.
Problem was reported by Dotan Barak <dotanb@dev.mellanox.co.il>.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Nothing looks at the return value of agent_send_response(), so there's
no point in returning anything.
Signed-off-by: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If agent_send_response() returns an error, we shouldn't do anything
differently than if it succeeds; setting response to NULL just means
that the response buffer gets leaked.
Signed-off-by: Suresh Shelvapille <suri@baymicrosystems.com>
Signed-off-by: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If ib_mad_recv_done_handler() fails to allocate response, then it just
printed a warning and continued, which leads to an oops if the MAD is
being handled for a switch device, because the switch code uses
response without checking for NULL. Fix this by bailing out of the
function if the allocation fails.
Signed-off-by: Suresh Shelvapille <suri@baymicrosystems.com>
Signed-off-by: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Now that ib_find_pkey() ignores the membership bit of P_Keys, there's no
need for ib_sa to look for both 0x7fff and 0xffff in a port's P_Key table.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ib_find_pkey() is used as a replacement for ib_find_cached_pkey(), and
the original function ignored the membership bit when searching for a
P_Key, so ib_find_pkey() should ignore the bit too.
In particular, IPoIB turns on the P_Key membership bit of limited
membership P_Keys when creating a child interface and looks for the
full membership P_key. This broke if a port was a partial member of a
partition when IPoIB switched from ib_find_cached_pkey() to
ib_find_pkey(), and this change fixes things again.
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
It was pointed out by Boaz Harrosh <bharrosh@panasas.com> that our
8.2.2 lpfc patches revert a change to using SCSI command accessor
functions.
This patch, to be applied on top of the 8.2.2. patches, updates the
driver for the accessor functions.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We want drivers/mtd/{mtdcore, mtdsuper, mtdpart}.c to be built and linked
into the same mtd.ko module. Fix the Makefile to ensure this, and remove
duplicate MODULE_ declarations in mtdpart.c, as mtdcore.c already has them.
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This is needed because commit 313674afa8
inlines the generic function to the caller.
Signed-off-by: Jan Altenberg <jan.altenberg@linutronix.de>
Signed-off-by: Li Yang <leoli@freescale.com>
This fix section mismatch:
reference to .exit.text:uec_mdio_exit (between 'ucc_geth_init' and 'uec_mdio_init')
void __exit uec_mdio_exit(void) is called from
- static int __init ucc_geth_init(void)
- static void __exit ucc_geth_exit(void)
First one would make error path more than just an error.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Li Yang <leoli@freescale.com>
The nand_base.c driver implicitly casts the uint32_t
eccpos array to 'int *', which is not only not guaranteed
to be the same sign as the source, but is not guaranteed
to be the same size.
Fix by changing nand_base.c to use uint32_t
referencing the eccpos fields.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The patch below fixes nand driver for AT91 boards which do not have NAND
R/B signal connected to gpio (rdy_pin is not connected).
Signed-off-by: Ivan Kuten <ivan.kuten@promwad.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
When we mark block bad we have to get chip because this involves
writing to the page's OOB. We hit this bug in UBI - we observed
random obscure crashes when it marks block bad from the background
thread and there is some parallel task which utilizes flash.
This patch also adds a TODO note about BBT table protection which
it seems does not exist.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The patch ensures that the current code (kernel 2.6.22) uses the bits
like the code prior to the refactoring. The variable "bits" is employed
in a useful way now.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This fixes a leak in the !mtd->erasesize error path (Coverity 1765).
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
As far as I know, all CardBus FireWire 400 adapters have a maximum
payload of 1024 bytes which is less than the speed-dependent limit of
2048 bytes. Fw-sbp2 has to take the host adapter's limit into account.
This apparently fixes Juju's incompatibility with my CardBus cards, a
NEC based card and a VIA based card.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Kristian Høgsberg <krh@redhat.com>
Make the option SBP2_PHYS_DMA available on all architectures where it
compiles. This includes x86-64 where I runtime-tested it successfully.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Revert commit 0555659d63 from 2.6.22-rc1.
The dma_set_mask call somehow failed on a PowerMac G5, PPC64:
http://lkml.org/lkml/2007/8/1/344
Should there ever occur a DMA mapping beyond the physical DMA range, a
proper SBP-2 firmware will report transport errors. So let's leave it
at that.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Tested-by: Olaf Hering <olh@suse.de>
Change a printk sequencing issue where <6> ... was coming up in the middle
of a line when scsi_add_host was being called.
Reduce the length of some printk messages and make the messages
more consistant. All cosmetic but it makes it easier to read as it
scrolles off the screen during boot.
Signed-off-by: Mark Fortescue <mark@mtfhpc.demon.co.uk>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If, in usb_hid_configure(), we fail to allocate storage for 'usbhid',
"if (!(usbhid = kzalloc(sizeof(struct usbhid_device), GFP_KERNEL)))",
then we'll jump to the 'fail:' label where we have this code:
usb_free_urb(usbhid->urbin);
usb_free_urb(usbhid->urbout);
usb_free_urb(usbhid->urbctrl);
Since we got here because we couldn't allocate storage for 'usbhid',
what we have here is a NULL pointer dereference - ouch...
This patch solves that little problem by adding a new
'fail_no_usbhid:' label after the problematic calls to
usb_free_urb() and jumps to that one instead, in the problem case.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
