I was hoping we could detect I2C devices at a given address without
actually writing data into them, but apparently some DDC slaves get
confused with 0-bytes transactions. Put the good old test back.
Reported-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
BIOS scripts usually make an attempt to reset the AGP controller,
however on some nv4x cards doing it properly involves switching FW off
and on: if we do that without updating the AGP bridge settings
accordingly (e.g. with the corresponding calls to agp_enable()) we
will be locking ourselves out of the card MMIO space. Do it from
nouveau_mem_reset_agp() before the init scripts are executed.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes the randomly flashing vertical lines seen on some nv3x after a
cold-boot.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes suspend+multihead on some boards that also use BIOS scripts for
modesetting.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Locking only makes sense in the VBIOS parsing code as it's executed
before CRTC init.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Clean up and move the external TV encoder detection code to
nouveau_i2c.c, it's also going to be useful for external TMDS and DDC
detection.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Init-compute-mem was the last piece missing for nv0x-nv3x card
cold-booting. This implementation is somewhat lacking but it's been
reported to work on most chipsets it was tested in. Let me know if it
breaks suspend to RAM for you.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Tested-by: Patrice Mandin <patmandin@gmail.com>
Tested-by: Ben Skeggs <bskeggs@redhat.com>
Tested-by: Xavier Chantry <chantry.xavier@gmail.com>
Tested-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Also collect all the PFB registers in a single place and remove some
duplicated definitions.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Rescaling interlaced modes isn't going to work correctly, and even if
it did, come on, interlaced flat panels? are you pulling my leg?
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
A previous commit started additionally using the SOR link when trying to
match the correct output script. However, we never fill in this field
for LVDS so we can never match a script at all.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There's a report of this quirk breaking modesetting on at least one board.
After discussion with Francisco Jerez, we've decided to remove it:
<darktama> it's not worth limiting the quirk to just where we know it can
work? i'm happy either way really :)
<curro> hmm, don't think so, most if not all DCB15 cards have just one DAC
<curro> and with that quirk there's no way to tell if the load comes from
the VGA or DVI port
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Acked-by: Francisco Jerez <currojerez@riseup.net>
On nv50 it became impossible to attempt a PCI ROM shadow of the VBIOS,
which will break some setups.
This patch also removes the different ordering of shadow methods for
pre-nv50 chipsets. The reason for the different ordering was paranoia,
but it should hopefully be OK to try shadowing PRAMIN first.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
On older cards (<nv17) scanout gets blocked when the ROM is being
accessed. PROM access usually comes out enabled from suspend, switch
it off.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
In some situations it's possible we can receive a spurious hotplug IRQ
before we're ready to handle it, leading to an oops.
Calling the display init before enabling interrupts should clear any
pending IRQs on the GPU and prevent this from happening.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
It seems on some chipsets that doing this from the 0x20 handler causes the
display engine to not ever signal the final 0x40 stage.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This removes the previous prepare_access() and finish_access() hooks, and
replaces it with a much simpler flush() hook.
All the chipset-specific code before nv50 has its use removed completely,
as it's not required there at all.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The previous handler basically worked correctly for a full-blown mode
change. However, it did nothing at all when a partial (encoder only)
reconfiguation was necessary, leading to the display hanging on certain
types of mode switch.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
