Add support for Analog Devices LT7182S Dual Channel 6A, 20V PolyPhase
Step-Down Silent Switcher with Digital Power System Management.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Several of the chips supported by this driver support configuring the
number of samples (or the fault queue depth) necessary before a fault
or alarm is reported. This is done either with a bit in the configuration
register or with a separate "consecutive alert" register. Support this
functionality with the temp_samples attribute.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add table with device names and known register values for supported
devices from Analog / ON Semiconductor.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NE1618 is similar to NE1617 but supports manufacturer and chip ID
registers as well as 11 bit external temperature resolution.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It was observed that the alert handler may be called from the i2c core
even after alerts have already been disabled. Only disable alerts if
they have not already been disabled.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ADT7421 is similar to ADT7461A but supports configurable Beta Compensation.
Packet Error Checking (PEC) is supported but undocumented.
A devicetree node is not added for the added chip since it is quite
unlikely that such an old chip will ever be used in a devicetree based
system. It can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT218 is compatible to NCT72 and NCT214. It also supports PEC (packet
error checking). Similar to NCT72 and NCT214, PEC support is undocumented.
Unlike NCT214 and NCT72, NCT218 does not support the undocumented secondary
chip and manufacturer ID registers at 0x3e and 0x3f and returns 0x00 when
reading those registers. The value for the chip revision register is not
documented but was observed to be 0xca. Use that information to improve
chip detection accuracy.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT214 and NCT72 are compatible to ADT7461/ADT7461A but have full
PEC (packet error checking) support. PEC support is undocumented.
Both chips support the undocumented secondary chip and manufacturer
ID registers at 0x3e and 0x3f, and return 0x61 as chip ID. Use this
information to improve the accuracy of chip detection code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Unlike ADM1023 and compatible chips, NCT210 does not support a temperature
offset register. A real chip was found to have a chip revision of 0x3f.
Use it to detect NCT210 explicitly.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LM86 and LM90 support exactly the same features, so there is no need
to keep their configuration options separate. Combine to reduce data
size.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
All chips supported by the ADM1021 driver are also supported by the LM90
driver. Make that support official.
After this change, the adm1021 driver is only needed if the lm90 driver
is disabled. Also, the adm1021 driver misdetects a variety of chips as
MAX1617A, which is unwanted if any of those chips is in the system.
For this reason. make the adm1021 driver dependent on !SENSORS_LM90 to
show that it is not needed if the lm90 driver is enabled, and to avoid
misdetection if a chip supported by the lm90 driver is in the system.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Both chips are quite similar to other chips of this series, so add
support for them to the lm90 driver. Also mention ON Semiconductor NCT210,
which is pin and register compatible to ADM1021A.
None of the chips support the secondary manufacturer and chip ID registers
at 0x3e and 0x3f, but return 0 when reading from those registers.
Use that information to improve the accuracy of chip detection code.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX1617 and LM84 are stripped-down versions of LM90, so they can easily
be supported by the LM90 driver. The most difficult part is chip detection,
since those old chips do not support manufacturer ID or chip ID registers.
The "alarms" attribute is enabled for both chips to match the functionality
of the adm1021 driver. Chip detection was improved and is less prone to
misdetection than the chip detection in the adm1021 driver.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Simplify the code a bit by handling single-register read operations
in lm90_read16(). All we need to do is to skip the low-byte read
operation if the register address is 0.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX6642 is a reduced version of LM90 with no low limits and no conversion
rate register. Its alert functionality is broken, similar to many other
chips supported by the lm90 driver.
After this change, the stand-alone max6642 driver is only needed if the
lm90 driver is disabled. Make it dependent on SENSORS_LM90=n to show that
it is not needed if the lm90 driver is enabled.
A devicetree node is not added for this chip since it is quite unlikely
that such an old chip will ever be used in a devicetree based system.
It can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A flag indicating support for setting the conversion rate doesn't cost
much and will enable us to add support for MAX6642 to the lm90 driver.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A flag indicating support for minimum temperature limits doesn't cost much
and will enable us to add support for MAX6642 to the lm90 driver.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX6690 is all but identical to MAX6654. Revision 1 of its
datasheet lists the same chip ID as MAX6654, and a chip labeled
MAX6654 was found to have the chip ID listed as MAX6690 chip ID
in Revision 2 of its datasheet.
A devicetree node is not added for this chip since it is quite unlikely
that such an old chip will ever be used in a devicetree based system.
It can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ADT7461A and NCT1008 support the undocumented manufacturer and chip ID
registers at 0x3e and 0x3f, and return 0x61 as chip ID. ADM1032 and
ADT7461 do not support those registers but return 0 when reading them.
Use this information to improve the accuracy of the chip detection code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ADT7481, ADT7482, and ADT7483 are similar to ADT7461, but support two
external temperature sensors, similar to MAX6695/6696. They support an
extended temperature range similar to ADT7461. Registers for the second
external channel can be accessed directly or by using the same method as
used by MAX6695/6696. For simplicity, the access method implemented for
MAX6695/6696 is used.
The chips support PEC (packet error checking). Set the PEC feature flag
and let the user decide if it should be enabled or not (it is by default
disabled).
Even though it is only documented for ADT7483, all three chips support a
secondary manufacturer ID register at 0x3e and a chip ID register at 0x3f.
Use the contents of those registers register for improved chip detection
accuracy. Add the same check to the ADT7461A detection code since this chip
also supports the same (undocumented) registers.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Reviewed-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Unlike MAX6646/MAX6647/MAX6649, MAX6648 and MAX6692 only support
a temperature range of 0..127 degrees C. Separate support for the
two sets of chips to be able to support maximum temperature ranges
correctly for all chips. Introduce new feature flag to indicate
temperature support up to 255 degrees C.
Since the chips are almost identical except for the supported temperature
range, automatic chip detection is limited. Effectively this means that
MAX6648 may be mis-detected as MAX6649 when auto-detected, but there is
nothing we can do about that.
Devicetree nodes are not added for the added chips since it is quite
unlikely that such old chips will ever be used in a devicetree based
system. They can be added later if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We don't want to support the obsolete 'alarms' attribute for new
chips supported by this driver. Add flag to indicate 'alarms' attribute
support and use it for existing chips. This flag will not be set for
additional chips supported by this driver in the future.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When support for G781 was added, chips with ID 0x01 were found at I2C
addresses 0x4c and 0x4d. The G781 datasheet (version 1.3 from October 2003)
says that the device ID for G781-1 is 0x03, not 0x01. Also, the datasheet
states that the chip at I2C address is G781 and the chip at I2C address
0x4d is G781-1.
A G781-1 at I2C address 0x4d was now found to have a chip ID of 0x03
as suggested by the datasheet. Accept both 0x01 and 0x03 chip IDs at both
addresses to ensure that all variants of G781 are detected properly.
While at it, improve chip detection accuracy by reading two additional
registers and ensuring that only expected bits are set in those registers.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The NCT1008 datasheet, Revision 3, states that its chip revision is
0x57. This matches the ADT7461A chip revision, and NCT1008 is therefore
detected as ADT7461A. In revision 6 of the datasheet, the chip revision
register is no longer documented. Multiple samples of NCT1008 were found
to report a chip revision of 0x54. As it turns out, one of the patches
submitted to add NCT1008 support to the lm90 driver already included a
check for chip revision 0x54. Unfortunately, that patch never made it into
the kernel. Remedy the situation and explicitly detect chips with revision
0x54 as NCT1008.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The detect function is getting larger and larger and difficult to
understand or review. Split it into per-manufacturer detect functions
to improve readability.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since temperature conversion functions are now unified, there is no need
to keep "the chip supports a configurable extended temperature range" and
"the chip has extended temperature range enabled" flags separate.
Use a single flag instead to reflect both.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
While most LM90 compatible chips support a temperature sensor resolution
of 11 bit, this is not the case for all chips. ADT7461 only supports a
resolution of 10 bit, and TMP451/TMP461 support a resolution of 12 bit.
Add support for various temperature sensor resolutions. To do this,
model all temperature sensors as 16 bit sensors, and use unified
temperature conversion functions which take the sensor resolution
as parameter.
While enhancing functionality, this has the positive side effect of
reducing code size by about 5%.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When reading 16-bit volatile registers, the code uses a trick to
determine if a temperature is consistent: It reads the high part
of the register twice. If the values are the same, the code assumes
that the reading is consistent. If the value differs, the code
re-reads the second register as well and assumes that it now has
correct values.
This is only necessary for volatile registers. Add a parameter to
lm90_read16() to indicate if the register is volatile to avoid the
extra overhead for non-volatile registers.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ADT7461 and TMP451 temperature sensors support extended temperature ranges.
If standard temperature range is selected, the temperature range is
unsigned and limited to 0 .. 127 degrees C. For TMP461, the standard
temperature range is -128000 ... 127000 degrees C. Distinguish between
the two chips by introducing a feature flag indicating if the standard
temperature range is signed or unsigned. Use the same flag for MAX6646/
MAX6647 as well since those chips also support unsigned temperatures.
Note that while the datasheet for ADT7461 suggests that the default
temperature range is unsigned, tests with a real chip suggest that this
is not the case: If the temperature offset is set to a value << 0,
the temperature register does report negative values.
Tests with real chips show that MAX6680/MAX6681 and SA56004 report
temperatures of 128 degrees C and higher as negative temperatures.
Add respective comments to the code.
Also use clamp_val() and DIV_ROUND_CLOSEST where appropriate in
calculations.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Experiments show that ADT7461A and NCT1008 support PEC, even though it is
not documented. Enable support for it in the driver. Since ADT7461 only
supports partial PEC, this means that the configuration for ADT7461A
needs to be separated from ADT7461.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Revision 0 of the ADT7461 datasheet suggests that the chip supports PEC
(packet error checking). This information is gone in later versions of the
datasheet. Experiments show that PEC support on ADT7461 is similar to PEC
support in ADM1032, ie it is only supported for read operations. Add
support for it to the driver.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
PEC (packet error checking) support for ADM1032 is currently only enabled
if the chip was auto-detected, but not if a chip is instantiated
explicitly. Always enable PEC support by introducing a chip feature flag
indicating partial PEC support. Also, for consistency, disable PEC support
by default to match existing functionality if the chip was not auto-
detected.
At the same time, introduce generic support for PEC with a separate feature
flag. This will be used when support for chips with full PEC functionality
is added.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The register write address either matches the read address, or it is the
read address plus 6. Simplify the code and resolve the write address
programmatically instead of having two defines for each register.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Handling bit shifts necessary to extract status bits during compile time
reduces code and data size by almost 5% when building for x86_64.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reorder chip enumeration in alphabetical order to make it easier to
see which chips are supported, and to clarify where to add support
new chip types. No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reorder include files in alphabetical order to reduce the chance of
duplicates and to make it clear where new include files should be
added. Drop the unnecessary include of linux/sysfs.h. Include
linux/device.h instead because that is what is actually used.
No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Many chips supported by this driver clear status registers after it
is read and update it in the next measurement cycle. Normally this falls
under the radar because all registers are only read once per measurement
cycle. However, there is an exception: Status registers are always read
during interrupt and laert handling. This can result in invalid status
reports if userspace reads an alarm attribute immediately afterwards.
Rework alarm/status handling by keeping a shadow register with 'current'
alarms, and by ensuring that the register is either only updated once per
measurement cycle or not cleared.
A second problem is related to alert handling: Alert handling is disabled
for chips with broken alert after an alert was reported, but only
re-enabled if attributes are read by the user. This means that alert
conditions may appear and disappear unnoticed. Remedy the situation
by introducing a worker to periodically read the status register(s) while
alert handling is disabled, and re-enable alerts after the alert condition
clears.
Yet another problem is that sysfs and udev events are currently only
reported to userspace if an alarm is raised, but not if an alarm condition
clears. Use the new worker to detect that situation and also generate
sysfs and udev events in that case.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
So far the driver only generated sysfs and udev events for minimum and
maximum alarms. Also generate events for critical and emergency alarms.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Enabling and disabling PEC for PMBus devices is currently only supported
with a debugfs attribute, which requires debugfs to be enabled and is
thus less than perfect. Take the lm90 driver as example and add a 'pec'
attribute to the I2C device if both the I2C adapter and the PMBus device
support it. Remove the now obsolete 'pec' attribute from debugfs.
Cc: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If platform_device_add() fails, it no need to call platform_device_del(), split
platform_device_unregister() into platform_device_del/put(), so platform_device_put()
can be called separately.
Fixes: 8808a793f0 ("ibmaem: new driver for power/energy/temp meters in IBM System X hardware")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220701074153.4021556-1-yangyingliang@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Drop the redundant word 'the' in the comments following
/*
* Set PHASE registers on all pages to 0xff to ensure that phase
* specific commands will apply to all phases of a given page (rail).
* This only affects the READ_IOUT and READ_TEMPERATURE2 registers.
* READ_IOUT will return the sum of currents of all phases of a rail,
* and READ_TEMPERATURE2 will return the maximum temperature detected
* for the [the - DROP] phases of the rail.
*/
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Link: https://lore.kernel.org/r/20220622063231.20612-1-jiangjian@cdjrlc.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Currently, the response to the power cap command overwrites the
first eight bytes of the poll response, since the commands use
the same buffer. This means that user's get the wrong data between
the time of sending the power cap and the next poll response update.
Fix this by specifying a different buffer for the power cap command
response.
Fixes: 5b5513b880 ("hwmon: Add On-Chip Controller (OCC) hwmon driver")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20220628203029.51747-1-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This fixes a regression where coma lead to concatenating board names
and broke module loading for C8H.
Fixes: 5b4285c57b ("hwmon: (asus-ec-sensors) fix Formula VIII definition")
Signed-off-by: Michael Carns <mike@carns.com>
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20220615122544.140340-1-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Unbinding the driver or removing the parent device at the same time
as using the OCC active sysfs file can cause the driver to unregister
the hwmon device twice. Prevent this by locking the occ mutex in the
shutdown function.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20220606185455.21126-1-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If no memory can be allocated, some resources still need to be released as
already done in the other error handling paths.
Fixes: 752b927951 ("hwmon: (aquacomputer_d5next) Add support for Aquacomputer Octo")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/be6b955d50de140fcc96bd116150b435021bf567.1653225250.git.christophe.jaillet@wanadoo.fr
Reviewed-by: Aleksa Savic <savicaleksa83@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Make sure that the support of PEC is determined before the read of other
registers. Otherwise the validation of PEC can trigger an error on the read
of STATUS_BYTE or STATUS_WORD registers.
The problematic scenario is the following. A device with enabled PEC
support is up and running and a kernel driver is loaded.
Then the driver is unloaded (or device unbound), the HW device
is reconfigured externally (e.g. by i2cset) to advertise itself as not
supporting PEC. Without the move of the code, at the second load of
the driver (or bind) the STATUS_BYTE or STATUS_WORD register is always
read with PEC enabled, which is likely to cause a read error resulting
with fail of a driver load (or bind).
Signed-off-by: Adam Wujek <dev_public@wujek.eu>
Link: https://lore.kernel.org/r/20220519233334.438621-1-dev_public@wujek.eu
Fixes: 75d2b2b06b ("hwmon: (pmbus) disable PEC if not enabled")
Fixes: 4e5418f787 ("hwmon: (pmbus_core) Check adapter PEC support")
[groeck: Added Fixes: tags, dropped continuation line]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Building arm:allmodconfig may fail with the following error.
In function 'fortify_memcpy_chk',
inlined from 'bitmap_copy' at include/linux/bitmap.h:261:2,
inlined from 'bitmap_copy_clear_tail' at include/linux/bitmap.h:270:2,
inlined from 'bitmap_from_u64' at include/linux/bitmap.h:622:2,
inlined from 'check_populated_dimms' at
drivers/hwmon/peci/dimmtemp.c:284:2:
include/linux/fortify-string.h:344:25: error:
call to '__write_overflow_field' declared with attribute warning:
detected write beyond size of field (1st parameter)
The problematic code is
bitmap_from_u64(priv->dimm_mask, dimm_mask);
dimm_mask is declared as u64, but the bitmap in priv->dimm_mask is only
24 bit wide. On 32-bit systems, this results in writes over the end of
the bitmap.
Fix the problem by using u32 instead of u64 for dimm_mask. This is
currently sufficient, and a compile time check to ensure that the number
of dimms does not exceed the bit map size is already in place.
Fixes: 73bc1b885d ("hwmon: peci: Add dimmtemp driver")
Cc: Iwona Winiarska <iwona.winiarska@intel.com>
Reviewed-by: Iwona Winiarska <iwona.winiarska@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some lm90 compatible devices can operate in an extended temperature mode.
This feature is now enabled if the property is set in the corresponding
device tree node.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220517135614.8185-2-holger.brunck@hitachienergy.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use ida_alloc()/ida_free() instead of deprecated
ida_simple_get()/ida_simple_remove() .
Signed-off-by: keliu <liuke94@huawei.com>
Link: https://lore.kernel.org/r/20220517063126.2142637-2-liuke94@huawei.com
[groeck: Updated subject to include driver name]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@s@
identifier i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@r@
initializer list elements;
identifier s.i;
@@
-u32 i[] = {
- elements,
- 0
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the coccinelle script.
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@s@
identifier i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@r@
initializer list elements;
identifier s.i;
@@
-u32 i[] = {
- elements,
- 0
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the coccinelle script.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@s@
identifier i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@r@
initializer list elements;
identifier s.i;
@@
-u32 i[] = {
- elements,
- 0
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the coccinelle script.
Cc: Iwona Winiarska <iwona.winiarska@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@s@
identifier i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@r@
initializer list elements;
identifier s.i;
@@
-u32 i[] = {
- elements,
- 0
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the coccinelle script.
Cc: Iwona Winiarska <iwona.winiarska@intel.com>
Reviewed-by: Iwona Winiarska <iwona.winiarska@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@s@
identifier i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@r@
initializer list elements;
identifier s.i;
@@
-u32 i[] = {
- elements,
- 0
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the coccinelle script.
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@s@
identifier i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@r@
initializer list elements;
identifier s.i;
@@
-u32 i[] = {
- elements,
- 0
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the coccinelle script.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.
The conversion was done automatically with coccinelle. The semantic patch
used to make this change is as follows.
@s@
identifier i,j,ty;
@@
-struct hwmon_channel_info j = {
- .type = ty,
- .config = i,
-};
@r@
initializer list elements;
identifier s.i;
@@
-u32 i[] = {
- elements,
- 0
-};
@script:ocaml t@
ty << s.ty;
elements << r.elements;
shorter;
elems;
@@
shorter :=
make_ident (List.hd(List.rev (Str.split (Str.regexp "_") ty)));
elems :=
make_ident
(String.concat ","
(List.map (fun x -> Printf.sprintf "\n\t\t\t %s" x)
(Str.split (Str.regexp " , ") elements)))
@@
identifier s.j,t.shorter;
identifier t.elems;
@@
- &j
+ HWMON_CHANNEL_INFO(shorter,elems)
This patch does not introduce functional changes. Many thanks to
Julia Lawall for providing the coccinelle script.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Various attempts were made recently to "convert" the old
hwmon_device_register() API to devm_hwmon_device_register_with_info()
by just changing the function name without actually converting the
driver. Prevent this from happening by making the 'chip' parameter of
devm_hwmon_device_register_with_info() mandatory.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The thermal subsystem registers a hwmon driver without providing
chip or sysfs group information. This is for legacy reasons and
would be difficult to change. At the same time, we want to enforce
that chip information is provided when registering a hwmon device
using hwmon_device_register_with_info(). To enable this, introduce
a special API for use only by the thermal subsystem.
Acked-by: Rafael J . Wysocki <rafael@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adds support for the ROG STRIX X570-E GAMING WIFI II board and
simplifies formatting for the list of supported models.
Signed-off-by: Debabrata Banerjee <dbavatar@gmail.com>
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20220505073351.123753-1-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver provides an i2c I/O mechanism for the core nct6775 driver,
as might be used by a BMC. Because the Super I/O chip is shared with
the host CPU in such a scenario (and the host should ultimately be in
control of it), the i2c driver is strictly read-only to avoid
interfering with any usage by the host (aside from the bank-select
register, which seems to be replicated for the i2c interface).
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Tested-by: Renze Nicolai <renze@rnplus.nl>
Link: https://lore.kernel.org/r/20220428012707.24921-3-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Boards such as
* PRO H410T
* PRIME H410M-R
* ROG STRIX X570-E GAMING WIFI II
have got a nct6775 chip, but by default there's no use of it
because of resource conflict with WMI method.
This commit adds such boards to the WMI monitoring list.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=204807
Signed-off-by: Denis Pauk <pauk.denis@gmail.com>
Reported-by: renedis <renedis@hotmail.com>
Reported-by: Dmitrii Levchenko <e_dimas@rambler.ru>
Reported-by: Hubert Banas <hubert.banas@gmail.com>
Link: https://lore.kernel.org/r/20220507072933.3013-1-pauk.denis@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some include directives are no longer necessary due to previous driver
changes. Remove them now to further improve driver code clarity.
Mutex usage has ceased since commit 719af4f1a4 ("hwmon: (lm83) Use
regmap").
Ever since commit a0ac840d99 ("hwmon: (lm83) Convert to use
devm_hwmon_device_register_with_groups") functions sysfs_create_group
and sysfs_remove_group are no longer used by the driver.
Signed-off-by: Karl Mehltretter <kmehltretter@gmail.com>
Link: https://lore.kernel.org/r/20220508144601.22796-1-kmehltretter@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The pmbus core does not have operations for getting or setting voltage.
Add functions get/set voltage for the dynamic regulator framework.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20220503104631.3515715-5-marten.lindahl@axis.com
[groeck: cosmetic alignment / empty line fixes]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some pmbus device drivers have device tree support and
may want to use of-thermal to register a thermal zone
OF sensor for those device drivers.
This way we allow describing device tree thermal zones
for pmbus device drivers with device tree support.
This patch achieves this by registering pmbus sensors
with thermal subsystem if they are PSC_TEMPERATURE
and are providing _input hwmon interface.
Cc: Guenter Roeck <linux@roeck-us.net> (maintainer:PMBUS HARDWARE MONITORING DRIVERS)
Cc: Jean Delvare <jdelvare@suse.com> (maintainer:HARDWARE MONITORING)
Cc: linux-hwmon@vger.kernel.org (open list:PMBUS HARDWARE MONITORING DRIVERS)
Cc: linux-kernel@vger.kernel.org (open list)
Signed-off-by: Eduardo Valentin <eduval@amazon.com>
Signed-off-by: Eduardo Valentin <evalenti@kernel.org>
Link: https://lore.kernel.org/r/20220428174926.2150-1-eduval@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Make use of enum chips and use a switch statement in load_attenuators()
so that the compiler can tell us if we've failed to cater for a
supported chip.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220323034056.260455-4-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The adt7473, adt7475, adt7476 and adt7490 have pins that can be used for
different functions. On the adt7473 and adt7475 this is pins 5 and 9.
On the adt7476 and adt7490 this is pins 10 and 14.
The first pin can either be PWM2(default) or SMBALERT#. The second pin
can be TACH4(default), THERM#, SMBALERT# or GPIO.
The adt7475 driver has always been able to detect the configuration if
it had been done by an earlier boot stage. Add support for configuring
the pins based on the hardware description in the device tree.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220323034056.260455-3-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the temperatur sensor and the fan controller on the
Microchip LAN966x SoC. Apparently, an Analog Bits PVT sensor is used
which can measure temperature and process voltages. But only a forumlae
for the temperature sensor is known. Additionally, the SoC support a fan
tacho input as well as a PWM signal to control the fan.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220401214032.3738095-5-michael@walle.cc
[groeck: Added missing reference in Documentation/hwmon/index.rst]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The polynomial calculation function was moved into lib/ to be able to
reuse it. Move over to this one.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220401214032.3738095-3-michael@walle.cc
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Several of the manuals for devices supported by this driver describes
the need for a minimum wait time before the chip is ready to receive
next command.
This wait time is already implemented in the driver as a ltc_wait_ready
function with a driver defined wait time of 100 ms, and is considered
for specific devices before reading/writing data on the pmbus.
Since this driver uses the default pmbus_regulator_ops for the enable/
disable/is_enabled functions we should add a driver specific callback
for write_byte_data to prevent bypassing the wait time recommendations
for the following devices: ltc3880/ltc3882/ltc3883/ltc3884/ltc3886/
ltc3887/ltc3889/ltm4664/ltm4675/ltm4676/ltm4677/ltm4678/ltm4680/ltm4686/
ltm4700/ltc7880.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20220428144039.2464667-4-marten.lindahl@axis.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some of the pmbus core functions uses pmbus_read_byte_data, which does
not support driver callbacks for chip specific write operations. This
could potentially influence some specific regulator chips that for
example need a time delay before each data access.
Lets use _pmbus_read_byte_data with callback check.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20220428144039.2464667-3-marten.lindahl@axis.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some of the pmbus core functions uses pmbus_write_byte_data, which does
not support driver callbacks for chip specific write operations. This
could potentially influence some specific regulator chips that for
example need a time delay before each data access.
Lets add support for driver callback with _pmbus_write_byte_data.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20220428144039.2464667-2-marten.lindahl@axis.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
DSDT code for AMD 400-series chipset shows that sensor addresses differ
for this generation from those for the AMD 500-series boards.
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20220427143001.1443605-4-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We need to keep some more information about the current board than just
the sensors set, and with more boards to add the dmi id array grows
quickly. Our probe code is always the same so let's switch to a custom
test code and a custom board info array. That allows us to omit board
vendor string (ASUS uses two strings that differ in case) in the board
info and use case-insensitive comparison, and also do not duplicate
sensor definitions for such board variants as " (WI-FI)" when sensors
are identical to the base variant.
Also saves a quarter of the module size by replacing big dmi_system_id
structs with smaller ones.
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20220427143001.1443605-2-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Instead of registering the hwmon device at probe time, use the
existing "occ_active" sysfs file to control when the driver polls
the OCC for sensor data and registers with hwmon. The reason for
this change is that the SBE, which is the device by which the
driver communicates with the OCC, cannot handle communications
during certain system state transitions, resulting in
unrecoverable system errors.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20220427140443.11428-1-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This splits the nct6775 driver into an interface-independent core and
a separate platform driver that wraps inb/outb port I/O (or asuswmi
methods) around that core.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Tested-by: Renze Nicolai <renze@rnplus.nl>
Link: https://lore.kernel.org/r/20220427010154.29749-7-zev@bewilderbeest.net
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Checkpatch has been warning about these for a while; the octal
versions are both more comprehensible and more concise.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20220427010154.29749-6-zev@bewilderbeest.net
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When enabled, all write bits are removed from the modes of all sysfs
attribute files. This provides a bit of infrastructure for the
upcoming i2c version of this driver, which should generally avoid
writes to device registers so as not to interfere with simultaneous
use of the device via the LPC interface.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20220427010154.29749-5-zev@bewilderbeest.net
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We now track the number of attribute groups in nct6775_data, as a
measure to simplify handling differences in the set of enabled
attribute groups between nct6775 drivers (platform & i2c). As a side
effect, we also reduce the amount of IS_ERR()/PTR_ERR() boilerplate a
bit.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20220427010154.29749-4-zev@bewilderbeest.net
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This replaces the nct6775_data->{read,write}_value function pointers
with a regmap.
The major difference is that the regmap access functions may fail, and
hence require checking at each call site. While the existing WMI
register-access code had potential failure paths, they were masked by
the fact that the read_value() function returned the register value
directly, and hence squashed errors undetectably by simply returning
zero, and while the write_value() functions were capable of reporting
errors, all callers ignored them.
This improves the robustness of the existing code, and also prepares
the driver for an i2c version to be added soon, for which register
accesses are much more likely to actually fail.
The conversion of the register-access call sites is largely mechanical
(reading a register now returns the value via an out-param pointer,
and returned errors must be checked for and propagated to callers),
though the nct6775_write_fan_div() function is refactored slightly to
avoid duplicating nearly identical (and now lengthier) code in each
switch case.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20220427010154.29749-3-zev@bewilderbeest.net
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If a particular SMM call takes a very long time to execute,
the user might experience audio problems. Print a warning
if a particular SMM call took over 0.250 seconds to execute,
so the user can check whether or not possible audio problems
are caused by this driver.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20220426213154.724708-4-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The default values for i8k_fan_mult and i8k_fan_max
should be assigend only if the values specified as
module params or in DMI are invalid/missing.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20220426213154.724708-3-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When the driver tries to detect the fan multiplier during
module initialisation, it issues one SMM call for each fan.
Those SMM calls are however redundant and also try to query
fans which may not be present.
Fix that by detecting the fan multiplier during hwmon
initialisation when no extra SMM calls are needed.
Also dont assume the last nominal speed entry to be the
biggest and instead check all entries.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20220426213154.724708-2-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When ti,n-factor, ti,beta-compentation are not defined in devicetree,
of_property_read_u32|s32 returns -EINVAL. In this case,
tmp401_init_client should return 0 instead of simply pass ret to its
caller.
Signed-off-by: Camel Guo <camel.guo@axis.com>
Link: https://lore.kernel.org/r/20220425100019.562781-1-camel.guo@axis.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adding another MAX16602 chip support to MAX16601 driver
Tested with MAX16602 works as expected.
Signed-off-by: Atif Ofluoglu <atif.ofluoglu@maximintegrated.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend aquacomputer_d5next driver to expose hardware
temperature sensors of the Aquacomputer Farbwerk RGB controller, which
communicates through a proprietary USB HID protocol.
Four temperature sensors are available. Additionally, serial number and
firmware version are exposed through debugfs.
Also, add Jack Doan to MAINTAINERS for this driver.
Signed-off-by: Jack Doan <me@jackdoan.com>
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/YmTcrq8Gzel0zYYD@jackdesk
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
S-34TS04A is a JC42 compatible 2-wire serial EEPROM with temperature sensor
from Seiko Instruments/ABLIC.
Signed-off-by: Oleksandr Shamray <oleksandrs@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
tmp401 driver supports TMP401, TMP411 and TMP43X temperature sensors.
According to their datasheet:
- all of them support extended temperature range feature;
- TMP411 and TPM43X support n-factor correction feature;
- TMP43X support beta compensation feature.
In order to support setting them during bootup, this commit reads
ti,extended-range-enable, ti,n-factor and ti,beta-compensation and set
the corresponding registers during probing.
Signed-off-by: Camel Guo <camel.guo@axis.com>
Link: https://lore.kernel.org/r/20220414075824.2634839-3-camel.guo@axis.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Until now, only the temperature sensors where exported thru
the thermal subsystem. Export the fans as "dell-smm-fan[1-3]" too
to make them available as cooling devices.
Also update Documentation and fix a minor issue with the alphabetic
ordering of the includes.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20220410163935.7840-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Instead of open-coding the bad characters replacement in the hwmon name,
use the new devm_hwmon_sanitize_name().
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Xu Yilun <yilun.xu@intel.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20220405092452.4033674-3-michael@walle.cc
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
More and more drivers will check for bad characters in the hwmon name
and all are using the same code snippet. Consolidate that code by adding
a new hwmon_sanitize_name() function.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20220405092452.4033674-2-michael@walle.cc
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend aquacomputer_d5next driver to expose hardware temperature sensors
and fans of the Aquacomputer Octo fan controller, which communicates
through a proprietary USB HID protocol.
Four temperature sensors and eight PWM controllable fans are available.
Additionally, serial number, firmware version and power-on count are
exposed through debugfs.
This driver has been tested on x86_64.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20220404134212.9690-1-savicaleksa83@gmail.com
[groeck: Add missing "select CRC16"]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use devm_delayed_work_autocancel() instead of hand writing it. This is
less verbose and saves a few lines of code.
devm_delayed_work_autocancel() uses devm_add_action() instead of
devm_add_action_or_reset(). This is fine, because if the underlying memory
allocation fails, no work has been scheduled yet. So there is nothing to
undo.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Iwona Winiarska <iwona.winiarska@intel.com>
Link: https://lore.kernel.org/r/fd277a708ede3882d7df6831f02d2e3c0cb813b8.1644781718.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add a thermal zone interface to the devices added
under jc42 driver. This way, thermal zones described
in device tree can make use of the of nodes of these
devices.
Cc: Guenter Roeck <linux@roeck-us.net> (maintainer:JC42.4 TEMPERATURE SENSOR DRIVER)
Cc: Jean Delvare <jdelvare@suse.com> (maintainer:HARDWARE MONITORING)
Cc: linux-hwmon@vger.kernel.org (open list:JC42.4 TEMPERATURE SENSOR DRIVER)
Cc: linux-kernel@vger.kernel.org (open list)
Signed-off-by: Eduardo Valentin <eduval@amazon.com>
Signed-off-by: Eduardo Valentin <evalenti@kernel.org>
Link: https://lore.kernel.org/r/20220318233011.13980-1-eduval@amazon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Building with SENSORS_LTQ_CPUTEMP=y with SOC_FALCON=y causes build
errors since FALCON does not support the same features as XWAY.
Change this symbol to depend on SOC_XWAY since that provides the
necessary interfaces.
Repairs these build errors:
../drivers/hwmon/ltq-cputemp.c: In function 'ltq_cputemp_enable':
../drivers/hwmon/ltq-cputemp.c:23:9: error: implicit declaration of function 'ltq_cgu_w32'; did you mean 'ltq_ebu_w32'? [-Werror=implicit-function-declaration]
23 | ltq_cgu_w32(ltq_cgu_r32(CGU_GPHY1_CR) | CGU_TEMP_PD, CGU_GPHY1_CR);
../drivers/hwmon/ltq-cputemp.c:23:21: error: implicit declaration of function 'ltq_cgu_r32'; did you mean 'ltq_ebu_r32'? [-Werror=implicit-function-declaration]
23 | ltq_cgu_w32(ltq_cgu_r32(CGU_GPHY1_CR) | CGU_TEMP_PD, CGU_GPHY1_CR);
../drivers/hwmon/ltq-cputemp.c: In function 'ltq_cputemp_probe':
../drivers/hwmon/ltq-cputemp.c:92:31: error: 'SOC_TYPE_VR9_2' undeclared (first use in this function)
92 | if (ltq_soc_type() != SOC_TYPE_VR9_2)
Fixes: 7074d0a927 ("hwmon: (ltq-cputemp) add cpu temp sensor driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Florian Eckert <fe@dev.tdt.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: linux-hwmon@vger.kernel.org
Link: https://lore.kernel.org/r/20220509234740.26841-1-rdunlap@infradead.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver doesn't have of_match_table. This makes the kernel module
tmp401.ko lack alias patterns (e.g: of:N*T*Cti,tmp411) to match DT node
of the supported devices hence this kernel module will not be
automatically loaded.
After adding of_match_table to this driver, the folllowing alias will be
added into tmp401.ko.
$ modinfo drivers/hwmon/tmp401.ko
filename: drivers/hwmon/tmp401.ko
......
author: Hans de Goede <hdegoede@redhat.com>
alias: of:N*T*Cti,tmp435C*
alias: of:N*T*Cti,tmp435
alias: of:N*T*Cti,tmp432C*
alias: of:N*T*Cti,tmp432
alias: of:N*T*Cti,tmp431C*
alias: of:N*T*Cti,tmp431
alias: of:N*T*Cti,tmp411C*
alias: of:N*T*Cti,tmp411
alias: of:N*T*Cti,tmp401C*
alias: of:N*T*Cti,tmp401
......
Fixes: af503716ac ("i2c: core: report OF style module alias for devices registered via OF")
Signed-off-by: Camel Guo <camel.guo@axis.com>
Link: https://lore.kernel.org/r/20220503114333.456476-1-camel.guo@axis.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
CLEAR_FAULTS commands can apparently sometimes trigger catastrophic
power output glitches on the ahe-50dc, so block them from being sent
at all.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220427035109.3819-1-zev@bewilderbeest.net
Fixes: d387d88ed0 ("hwmon: (pmbus) Add Delta AHE-50DC fan control module driver")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Explicitly disable PEC when the client does not support it.
The problematic scenario is the following. A device with enabled PEC
support is up and running and a kernel driver is loaded.
Then the driver is unloaded (or device unbound), the HW device
is reconfigured externally (e.g. by i2cset) to advertise itself as not
supporting PEC. Without a new code, at the second load of the driver
(or bind) the "flags" variable is not updated to avoid PEC usage. As a
consequence the further communication with the device is done with
the PEC enabled, which is wrong and may fail.
The implementation first disable the I2C_CLIENT_PEC flag, then the old
code enable it if needed.
Fixes: 4e5418f787 ("hwmon: (pmbus_core) Check adapter PEC support")
Signed-off-by: Adam Wujek <dev_public@wujek.eu>
Link: https://lore.kernel.org/r/20220420145059.431061-1-dev_public@wujek.eu
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
All temperature of Fintek superio hwmonitor that using 1-byte reg will use
2's complement.
In show_temp()
temp = data->temp[nr] * 1000;
When data->temp[nr] read as 255, it indicate -1C, but this code will report
255C to userspace. It'll be ok when change to:
temp = ((s8)data->temp[nr]) * 1000;
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Link: https://lore.kernel.org/r/20220418090706.6339-1-hpeter+linux_kernel@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When removing the adt7470 module, a warning might be printed:
do not call blocking ops when !TASK_RUNNING; state=1
set at [<ffffffffa006052b>] adt7470_update_thread+0x7b/0x130 [adt7470]
This happens because adt7470_update_thread() can leave the kthread in
TASK_INTERRUPTIBLE state when the kthread is being stopped before
the call of set_current_state(). Since kthread_exit() might sleep in
exit_signals(), the warning is printed.
Fix that by using schedule_timeout_interruptible() and removing
the call of set_current_state().
This causes TASK_INTERRUPTIBLE to be set after kthread_should_stop()
which might cause the kthread to exit.
Reported-by: Zheyu Ma <zheyuma97@gmail.com>
Fixes: 93cacfd41f (hwmon: (adt7470) Allow faster removal)
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Tested-by: Zheyu Ma <zheyuma97@gmail.com>
Link: https://lore.kernel.org/r/20220407101312.13331-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
0-day reports:
drivers/hwmon/pmbus/xdpe12284.c:127:36: warning:
unused variable 'xdpe122_reg_desc'
This is seen if CONFIG_SENSORS_XDPE122_REGULATOR is not enabled.
Mark xdpe122_reg_desc as __maybe_unused to fix the problem.
Fixes: f53bfe4d69 ("hwmon: (xdpe12284) Add regulator support")
Reported-by: kernel test robot <lkp@intel.com>
Cc: Marcello Sylvester Bauer <sylv@sylv.io>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
There will be two merge conflicts with your tree, one in MAINTAINERS
which is obvious to fix up, and one in drivers/phy/freescale/Kconfig
which also should be easy to resolve.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYkG3fQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykNEgCfaRG8CRxewDXOO4+GSeA3NGK+AIoAnR89donC
R4bgCjfg8BWIBcVVXg3/
=WWXC
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (556 commits)
firmware: google: Properly state IOMEM dependency
kgdbts: fix return value of __setup handler
firmware: sysfb: fix platform-device leak in error path
firmware: stratix10-svc: add missing callback parameter on RSU
arm64: dts: qcom: add non-secure domain property to fastrpc nodes
misc: fastrpc: Add dma handle implementation
misc: fastrpc: Add fdlist implementation
misc: fastrpc: Add helper function to get list and page
misc: fastrpc: Add support to secure memory map
dt-bindings: misc: add fastrpc domain vmid property
misc: fastrpc: check before loading process to the DSP
misc: fastrpc: add secure domain support
dt-bindings: misc: add property to support non-secure DSP
misc: fastrpc: Add support to get DSP capabilities
misc: fastrpc: add support for FASTRPC_IOCTL_MEM_MAP/UNMAP
misc: fastrpc: separate fastrpc device from channel context
dt-bindings: nvmem: brcm,nvram: add basic NVMEM cells
dt-bindings: nvmem: make "reg" property optional
nvmem: brcm_nvram: parse NVRAM content into NVMEM cells
nvmem: dt-bindings: Fix the error of dt-bindings check
...
- Add support for Maxim MAX77714 PMIC
- Remove Drivers
- Remove support for ST-Ericsson AB8500 DebugFS
- New Device Support
- Add support for Silergy SY7636A to Simple MFD I2C
- Add support for MediaTek MT6366 PMIC to MT6358 IRQ
- Add support for Charger to Intel PMIC CRC
- Add support for Raptor Lake to Intel LPSS PCI
- New Functionality
- Add support for Reboot to Rockchip RK808
- Fix-ups
- Device Tree changes (inc. YAML conversion); silergy,sy7636a, maxim,max77843,
google,cros-ec, maxim,max14577, maxim,max77802,
maxim,max77714, qcom,tcsr, qcom,spmi-pmic,
stericsson,ab8500, stericsson,db8500-prcmu,
samsung,exynos5433-lpass, mt6397, syscon, brcm,cru
- Visible to menuconfig; simple-mfd-i2c
- Clean-up or clarify code; max77686, intel_soc_pmic_crc
- Improve error handling; mc13xxx-core, stmfx, asic3
- Pass device information to child devices; iqs62x, intel-lpss-acpi
- Individually identify IRQ domains; intel_soc_pmic_core
- Remove superfluous code; dbx500-prcmu, exynos-lpass
- Staticify and constify; arizona-i2c
- Mark sometimes used data as __maybe_unused; atmel-flexcom
- Account for different ACPI tables on AOSP/Windows platforms; arizona-spi
- Use provided (platform) APIs; ab8500-core
- Trivial (whitespace, spelling); rohm-bd9576
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEdrbJNaO+IJqU8IdIUa+KL4f8d2EFAmI9n1YACgkQUa+KL4f8
d2F59RAAi3zTun+i7NEvaPs4awcXgUv9ZFJmP/AcCTvKwmAnom4JHc56c86yE/Fz
IwQ/yug60AQPMe05jw4+KxD87URLGKb/IDTzmRvnC29gwg1FR5A2bFNJ+wveK6od
cN0r40lvHCzVASwOeF2E63RzXcWHFg+tuNq6qm+HQ6LX31MpMe/dfMOCvVm+1A50
aOn2cnEiUw7mhEiEy0CPtd01hjBEu4QS8xzZwGu/4lHEbInDxpAakQP8ixYE0THF
KEvR2gFS6G6wYHO3ZQOJHQJnnzL1nmLtsUX3q+5+DIKnLcY/1xofdxloHAH18i+9
8e9nDB4TVPAHCpiSVFmPtzS7TR5ofkaYIvpxKlolBVgXGkAivYrtcQUMPEG6ZbNL
wpe6j2IB7EeQeh0z8k9mzr6zZ3Dw5EGcytvAMP3SZAsHpy+uiZ0TOqPdFs1NXLJ7
7rlpUhlgn2Ar5TI+z5DLeZsKSO8Lb9+X6BlXfblT0dNBclmh52suWwp1yx7hCehD
mFm7JfkU7+/9XlzkxYqyyl/3qmmuiXfrxf5Uc96kwcczFkXli8z2Q5Jli6dmCq5+
LE9hkLk6JC5m5QpRv8cg06sHraDbPbTnrrhf5w6txukU+HsldxcQNaJMqLhHCPQ4
CUYWRImr0no8PJZQkslIgWaqkpQejS5UzPQbFnkQblvP2XMvOFU=
=1xnI
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for Maxim MAX77714 PMIC
Removed Drivers:
- Remove support for ST-Ericsson AB8500 DebugFS
New Device Support:
- Add support for Silergy SY7636A to Simple MFD I2C
- Add support for MediaTek MT6366 PMIC to MT6358 IRQ
- Add support for Charger to Intel PMIC CRC
- Add support for Raptor Lake to Intel LPSS PCI
New Functionality:
- Add support for Reboot to Rockchip RK808
Fix-ups:
- Device Tree changes (includcing YAML conversion) for
silergy,sy7636a, maxim,max77843, google,cros-ec, maxim,max14577,
maxim,max77802, maxim,max77714, qcom,tcsr, qcom,spmi-pmic,
stericsson,ab8500, stericsson,db8500-prcmu,
samsung,exynos5433-lpass, mt6397, syscon, brcm,cru
- Visible to menuconfig; simple-mfd-i2c
- Clean-up or clarify code; max77686, intel_soc_pmic_crc
- Improve error handling; mc13xxx-core, stmfx, asic3
- Pass device information to child devices; iqs62x, intel-lpss-acpi
- Individually identify IRQ domains; intel_soc_pmic_core
- Remove superfluous code; dbx500-prcmu, exynos-lpass
- Staticify and constify; arizona-i2c
- Mark sometimes used data as __maybe_unused; atmel-flexcom
- Account for different ACPI tables on AOSP/Windows platforms; arizona-spi
- Use provided (platform) APIs; ab8500-core
- Trivial (whitespace, spelling); rohm-bd9576"
* tag 'mfd-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (50 commits)
dt-bindings: mfd: syscon: Add microchip,lan966x-cpu-syscon compatible
mfd: bd9576: fix typos in comments
mfd: Use platform_get_irq() to get the interrupt
mfd: db8500-prcmu: Remove unused inline function
mfd: arizona-spi: Add Android board ACPI table handling
mfd: arizona-spi: Split Windows ACPI init code into its own function
mfd: asic3: Add missing iounmap() on error asic3_mfd_probe
MAINTAINERS: Rectify entry for ROHM MULTIFUNCTION BD9571MWV-M PMIC DEVICE DRIVERS
mfd: intel-lpss: Provide an SSP type to the driver
dt-bindings: mfd: brcm,cru: Rename pinctrl node
dt-bindings: Add compatibles for undocumented trivial syscons
mfd: atmel-flexcom: Fix compilation warning
dt-bindings: mfd: Add compatible for the MediaTek MT6366 PMIC
dt-bindings: mfd: samsung,exynos5433-lpass: Convert to dtschema
mfd: exynos-lpass: Drop unneeded syscon.h include
mfd: intel-lpss: Add Intel Raptor Lake PCH-S PCI IDs
mfd: ab8500: Drop debugfs module
mfd: sta2x11: Use GFP_KERNEL instead of GFP_ATOMIC
mfd: ab8500: Rewrite bindings in YAML
mfd: qcom-spmi-pmic: Add pm8953 compatible
...
The overwhelming bulk of this pull request is a change from Uwe
Kleine-König which changes the return type of the remove() function to
void as part of some wider work he's doing to do this for all bus types,
causing updates to most SPI device drivers. The branch with that on has
been cross merged with a couple of other trees which added new SPI
drivers this cycle, I'm not expecting any build issues resulting from
the change.
Otherwise it's been a relatively quiet release with some new device
support, a few minor features and the welcome completion of the
conversion of the subsystem to use GPIO descriptors rather than numbers:
- Change return type of remove() to void.
- Completion of the conversion of SPI controller drivers to use GPIO
descriptors rather than numbers.
- Quite a few DT schema conversions.
- Support for multiple SPI devices on a bus in ACPI systems.
- Big overhaul of the PXA2xx SPI driver.
- Support for AMD AMDI0062, Intel Raptor Lake, Mediatek MT7986 and
MT8186, nVidia Tegra210 and Tegra234, Renesas RZ/V2L, Tesla FSD and
Sunplus SP7021.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmI4b+8ACgkQJNaLcl1U
h9AB+Qf/WhPzDSCdhK1repnSmEpRNs/J6hItmY2H6pTQaWALpfTB0+p1Nb5tAotg
fHbu6a2AsiiwWt+tDal44GFYhS0CDSOT4hqgLV8msyDDPPJqqr7A2dbu7YrCjTVI
TgNZNwxW7c2LgqBXR9GV7NPWYoxYxveoYh+L+05MSuSQxSOvPl6LUZiZPnPufQM6
dCpEh19atrtasFg3rFnslWBd2C3h8hb6YT7vUZs9gxhg3FvSgpYQwzz5SfFgHXK6
Rg07m8fDTSjf2qo1C4pc/d1Ni1xBe7aHKMtjtR3jJ4q8QqiawfCcvvOep/Iaec1+
s3qnDthohWMJoF1W6ERf3HiAgNIfhg==
=4tlR
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The overwhelming bulk of this pull request is a change from Uwe
Kleine-König which changes the return type of the remove() function to
void as part of some wider work he's doing to do this for all bus
types, causing updates to most SPI device drivers. The branch with
that on has been cross merged with a couple of other trees which added
new SPI drivers this cycle, I'm not expecting any build issues
resulting from the change.
Otherwise it's been a relatively quiet release with some new device
support, a few minor features and the welcome completion of the
conversion of the subsystem to use GPIO descriptors rather than
numbers:
- Change return type of remove() to void.
- Completion of the conversion of SPI controller drivers to use GPIO
descriptors rather than numbers.
- Quite a few DT schema conversions.
- Support for multiple SPI devices on a bus in ACPI systems.
- Big overhaul of the PXA2xx SPI driver.
- Support for AMD AMDI0062, Intel Raptor Lake, Mediatek MT7986 and
MT8186, nVidia Tegra210 and Tegra234, Renesas RZ/V2L, Tesla FSD and
Sunplus SP7021"
[ And this is obviously where that spi change that snuck into the
regulator tree _should_ have been :^]
* tag 'spi-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (124 commits)
spi: fsi: Implement a timeout for polling status
spi: Fix erroneous sgs value with min_t()
spi: tegra20: Use of_device_get_match_data()
spi: mediatek: add ipm design support for MT7986
spi: Add compatible for MT7986
spi: sun4i: fix typos in comments
spi: mediatek: support tick_delay without enhance_timing
spi: Update clock-names property for arm pl022
spi: rockchip-sfc: fix platform_get_irq.cocci warning
spi: s3c64xx: Add spi port configuration for Tesla FSD SoC
spi: dt-bindings: samsung: Add fsd spi compatible
spi: topcliff-pch: Prevent usage of potentially stale DMA device
spi: tegra210-quad: combined sequence mode
spi: tegra210-quad: add acpi support
spi: npcm-fiu: Fix typo ("npxm")
spi: Fix Tegra QSPI example
spi: qup: replace spin_lock_irqsave by spin_lock in hard IRQ
spi: cadence: fix platform_get_irq.cocci warning
spi: Update NXP Flexspi maintainer details
dt-bindings: mfd: maxim,max77802: Convert to dtschema
...
Sadly, while firmware 1.5 fixed temperature labels on my
Inspiron 3505, it also caused fan type calls to take
ca. 4 seconds with the fan being at full speed.
Fix the resulting delays by adding the model to the
blacklist.
Tested on a Dell Inspiron 3505.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20220318183408.13286-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If there is an input undervoltage fault, reported in STATUS_INPUT
command response, there is quite likely a "Unit Off For Insufficient
Input Voltage" condition as well.
Add a constant for bit 3 of STATUS_INPUT. Update the Vin limit
attributes to include both bits in the mask for clearing faults.
If an input undervoltage fault occurs, causing a unit off for
insufficient input voltage, but the unit is off bit is not cleared, the
STATUS_WORD will not be updated to clear the input fault condition.
Including the unit is off bit (bit 3) allows for the input fault
condition to completely clear.
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Link: https://lore.kernel.org/r/20220317232123.2103592-1-bjwyman@gmail.com
Fixes: b4ce237b7f ("hwmon: (pmbus) Introduce infrastructure to detect sensors and limit registers")
[groeck: Dropped unnecessary ()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use of_device_get_match_data() to simplify the code.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Link: https://lore.kernel.org/r/20220315023412.2118415-1-chi.minghao@zte.com.cn
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for Texas Instruments TMP464 and TMP468 temperature sensor
ICs.
TI's TMP464 is an I2C temperature sensor chip. This chip is similar
to TI's TMP421 chip, but with 16bit-wide registers (instead of
8bit-wide registers). The chip has one local sensor and four remote
sensors. TMP468 is similar to TMP464 but has one local and eight
remote sensors.
Originally-from: Agathe Porte <agathe.porte@nokia.com>
Cc: Agathe Porte <agathe.porte@nokia.com>
Cc: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Tested-by: Agathe Porte <agathe.porte@nokia.com>
Link: https://lore.kernel.org/r/20220222223610.23098-2-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Current driver assume PWR_AVG and VI_AVG as 1 by default, and user needs
to set sample averaging via sysfs manually.
This patch parses the properties "adi,power-sample-average" and
"adi,volt-curr-sample-average" from device tree, and setting sample
averaging during probe. Input value must be one of value in the
list [1, 2, 4, 8, 16, 32, 64, 128].
Signed-off-by: Potin Lai <potin.lai@quantatw.com>
Link: https://lore.kernel.org/r/20220302123817.27025-2-potin.lai@quantatw.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for another Infineon Multi-phase controller chip. The
xdpe11280 uses linear instead of vid data format for VOUT. Detect
VOUT_MODE format during identification and skip the xdpe122 related
adaptions in case it is linear.
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Link: https://lore.kernel.org/r/fa6a4b636a05ecb337d132824efca2545188a2a2.1646214248.git.sylv@sylv.io
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend aquacomputer_d5next driver to expose hardware temperature sensors
of the Aquacomputer Farbwerk 360 RGB controller, which communicates through
a proprietary USB HID protocol.
Four temperature sensors are available. Additionally, serial number and
firmware version are exposed through debugfs.
This driver has been tested on x86_64.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
After doing some research, it seems that Fujitsu's
hardware monitoring solution exports data describing
which temperature sensors affect which fans, similar
to the data in fan_source of the ftsteutates driver.
Writing 0 into these registers forces the fans to
full speed.
Export this data with standard attributes.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20220224061210.16452-3-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pwm[1-*]_auto_channels_temp is documented as an official
hwmon sysfs attribute, yet there is no support for it in
the new with_info-API. Fix that.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20220224061210.16452-2-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The TMP125 is a 2 degree Celsius accurate Digital
Temperature Sensor with a SPI interface.
The temperature register is a 16-bit, read-only register.
The MSB (Bit 15) is a leading zero and never set. Bits 14
to 5 are the 1+9 temperature data bits in a two's
complement format. Bits 4 to 0 are useless copies of
Bit 5 value and therefore ignored.
This was tested on a Aerohive HiveAP-350.
Bonus: lm70 supports TMP122/TMP124 as well.
I added them to the Kconfig module description.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://lore.kernel.org/r/43b19cbd4e7f51e9509e561b02b5d8d0e7079fac.1645175187.git.chunkeey@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Export the power caps data for the soft minimum power cap through hwmon.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20220215151022.7498-5-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add regulator supply into PWBUS_REGULATOR macro. This makes it optional
to define a vin-supply in DT. Not defining a supply will add a dummy
regulator supply instead and only cause the following debug output:
```
Looking up vin-supply property in node [...] failed
```
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Link: https://lore.kernel.org/r/58f2ff7b90233fad3d7ae2e9d66d5192e2c1ac01.1645437439.git.sylv@sylv.io
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On the Dell Inspiron 3505, three temperature sensors are
available through the SMM interface. However since they
do not have an associated type, they are not detected.
Probe for those sensors in case no type was detected.
_i8k_get_temp() is used instead of i8k_get_temp()
since it is sometimes faster and the result is
easier to check (no -ENODATA) since we do not
care about the actual temp value.
Tested on a Dell Inspiron 3505.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20220215191113.16640-5-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Right now, we only use bits 0 to 7 of the fan/temp sensor number
by doing number & 0xff. Passing the value as a u8 makes this
step unnecessary. Also add checks to the ioctl handler since
users might get confused when passing 0x00000101 does the same
as passing 0x00000001.
Tested on a Dell Inspiron 3505.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20220215191113.16640-4-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When enabling said module parameter, the driver ignores
all feature blacklists on relevant models, which has the
potential for strange side effects. Also there seems to
be a slight chance for unsupported devices to behave
badly when probed for features.
In such cases, the kernel should be tainted to inform
people that these issues might have been caused by
the dell_smm_hwmon driver with "force" enabled.
Also reword the parameter description to remind users
that enabling "force" also enables blacklisted features.
Tested on a Dell Inspiron 3505.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20220215191113.16640-8-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add sysfs entries for DVFS due to a VRM Vdd over-temperature condition,
and add the GPU throttling condition bits (such that if bit 1 is set,
GPU1 is throttling).
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20220215151022.7498-4-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
BMC control applications need to check the OCC mode returned by the
OCC poll response, so export it in sysfs with the other OCC-specific
data.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20220215151022.7498-3-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
BMC control applications need to check the Idle Power Saver status
byte returned by the OCC poll response, so export it in sysfs with
the other OCC-specific data.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20220215151022.7498-2-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Remove the call to dev_info() from the board detection function, which
is called from probe(), not only to be in line with hwmon driver rules, but
also because the message duplicates the error code returned from probe()
for that case (ENODEV).
Changes in:
- v2: add missing newline (style).
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20220217194318.2960472-1-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
While these chips aren't strictly advertised as voltage regulators per
se, they (aside from the lm25056) support the PMBus OPERATION command
to enable and disable their outputs and have status bits for reporting
various warnings and faults, and can hence usefully support all the
pmbus_regulator_ops operations.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20220219000742.20126-1-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The various PMBus status bits don't all map perfectly to the more
limited set of REGULATOR_ERROR_* flags, but there's a reasonable
number where they correspond well enough.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20220219000359.19985-1-zev@bewilderbeest.net
[groeck: Added missing locking]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reading DSDT code for ASUS X470-based boards (the ones served by the
asus_wmi_Sensors driver), where ASUS put hardware monitoring functions
into the WMI code, reveals that fan and current sensors data is
unsigned. For the current sensor that was confirmed by a user who showed
high enough current value for overflow.
Thus let's assume that the signedness of the sensors is determined by its
type and that only temperature ones provide signed numbers.
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20220211164855.265698-1-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adds thermal_cooling device support to the tc654/tc655
driver. This make it possible to integrate it into a
device-tree supported thermal-zone node as a
cooling device.
I have been using this patch as part of the Netgear WNDR4700
Centria NAS Router support within OpenWrt since 2016.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://lore.kernel.org/r/20220213004733.2421193-1-chunkeey@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It is not the laptops, but the /proc/i8k interface that is legacy (or so
I think was the intention of the help text author). The old description
was confusing, fix this.
The phrase "Say Y if you intend to run this kernel on old Dell laptops
or want to use userspace package i8kutils." was introduced in 2015, in
commit 039ae58503 ("hwmon: Allow to compile dell-smm-hwmon driver without /proc/i8k")
I think that "old laptops" was about hotkey and Fn key support - this
driver in the 2.4 kernels' era apparently had these capabilities
(see: https://github.com/vitorafsr/i8kutils , description of
"repeat_rate" kernel module parameter).
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Cc: Pali Rohár <pali@kernel.org>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Mark Gross <markgross@kernel.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20220212125654.357408-2-mat.jonczyk@o2.pl
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In Kconfig, inside the "Processor type and features" menu, there is
the CONFIG_I8K option: "Dell i8k legacy laptop support". This is
very confusing - enabling CONFIG_I8K is not required for the kernel to
support old Dell laptops. This option is specific to the dell-smm-hwmon
driver, which mostly exports some hardware monitoring information and
allows the user to change fan speed.
This option is misplaced, so move CONFIG_I8K to drivers/hwmon/Kconfig,
where it belongs.
Also, modify the dependency order - change
select SENSORS_DELL_SMM
to
depends on SENSORS_DELL_SMM
as it is just a configuration option of dell-smm-hwmon. This includes
changing the option type from tristate to bool. It was tristate because
it could select CONFIG_SENSORS_DELL_SMM=m .
When running "make oldconfig" on configurations with
CONFIG_SENSORS_DELL_SMM enabled , this change will result in an
additional question (which could be printed several times during
bisecting). I think that tidying up the configuration is worth it,
though.
Next patch tweaks the description of CONFIG_I8K.
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Cc: Pali Rohár <pali@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Mark Gross <markgross@kernel.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220212125654.357408-1-mat.jonczyk@o2.pl
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A user discovered [1] the CPU Core voltage sensor, which spans 2
registers and provides output in mV. Althroug the discovery was made
with a X470 chipset, the sensor is present in X570 (tested with C8H).
For now simply add it to each board with the CPU current sensor present.
[1] https://github.com/zeule/asus-ec-sensors/issues/12
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Denis Pauk <pauk.denis@gmail.com>
Link: https://lore.kernel.org/r/20220208094244.1106312-1-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Describe the only available channel, implement read, write
and is_visible callbacks.
Also, pass name to core driver for the i2c device so that
it can be used to register hwmon device.
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Link: https://lore.kernel.org/r/20211221215841.2641417-4-demonsingur@gmail.com
[groeck: Adjusted to use regmap]
Tested-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Reviewed-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Using regmap lets us use the regmap subsystem for SPI vs. I2C register
accesses. It lets us hide access differences in backend code and lets
the common code just access registers without knowing their size.
We can also use regmap for register caching.
Tested-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Reviewed-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Temperature sensor readings are signed, which is hinted by their blank
value (oxd8, 216 as unsigned and -40 as signed). T_Sensor, Crosshair
VIII Hero, and a freezer were used to confirm that.
Here we read fan sensors as signed too, because with their typical
values and 2-byte width, I can't tell a difference between signed and
unsigned, as I don't have a high speed chipset fan.
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20220204163045.576903-1-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There is no such struct as "asus_ec_sensors", it was supposed to be
"ec_sensors_data". This typo does not affect either build or runtime.
Fixes: c4b1687d6897 ("hwmon: (asus-ec-sensors) add driver for ASUS EC")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220205092015.GA612@kili
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Recently 'cur_state' user space 'sysfs' interface 'sysfs' has been
deprecated. This interface is used in Nvidia systems for setting fan
speed limit. Currently fan speed limit is set from the user space by
setting 'sysfs' 'cur_state' attribute to 'max_state + n', where 'n' is
required limit, for example: 15 for 50% speed limit, 20 for full fan
speed enforcement.
The purpose of this feature is to provides ability to limit fan speed
according to some system wise considerations, like absence of some
replaceable units (PSU or line cards), high system ambient temperature,
unreliable transceivers temperature sensing or some other factors which
indirectly impacts system's airflow.
The motivation is to support fan low limit feature through 'hwmon'
interface.
Use 'hwmon' 'pwm' attribute for setting low limit for fan speed in
case 'thermal' subsystem is configured in kernel. In this case setting
fan speed through 'hwmon' will never let the 'thermal' subsystem to
select a lower duty cycle than the duty cycle selected with the 'pwm'
attribute.
From other side, fan speed is to be updated in hardware through 'pwm'
only in case the requested fan speed is above last speed set by
'thermal' subsystem, otherwise requested fan speed will be just stored
with no PWM update.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20220126141825.13545-1-vadimp@nvidia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver provides the same data as the asus_wmi_ec_sensors driver
(and gets it from the same source) but does not use WMI, polling
the ACPI EC directly.
That provides two enhancements: sensor reading became quicker (on some
systems or kernel configuration it took almost a full second to read
all the sensors, that transfers less than 15 bytes of data), the driver
became more flexible. The driver now relies on ACPI mutex to lock access
to the EC in the same way as the WMI code does.
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20220124015658.687309-2-eugene.shalygin@gmail.com
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Denis Pauk <pauk.denis@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If the watchdog was already enabled by the BIOS after booting, the
watchdog infrastructure needs to regularly send keepalives to
prevent a unexpected reset.
WDOG_ACTIVE only serves as an status indicator for userspace,
we want to use WDOG_HW_RUNNING instead.
Since my Fujitsu Esprimo P720 does not support the watchdog,
this change is compile-tested only.
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Fixes: fb551405c0 (watchdog: sch56xx: Use watchdog core)
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20220131211935.3656-5-W_Armin@gmx.de
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
msleep(1) will often sleep more than 20ms, slowing down sensor
and watchdog reads/writes. Use usleep_range() as recommended
in timers-howto.rst to fix that.
Tested on a Fujitsu Esprimo P720.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20220131211935.3656-4-W_Armin@gmx.de
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch enables the sch56xx-common module to get automatically
loaded on supported machines.
If a machine supports Fujitsu's SCH56XX-based hardware monitoring
solutions, it contains a "Antiope"/" Antiope" dmi onboard device
in case of the sch5627 or a "Theseus"/" Theseus" dmi onboard device
in case of the sch5636.
Since some machines like the Esprimo C700 have a seemingly faulty
DMI table containing both onboard devices, the driver still needs
to probe for the individual superio chip, which in presence of at
least one DMI onboard device however can be considered safe.
Also add a module parameter allowing for bypassing the
DMI check.
Tested on a Fujitsu Esprimo P720.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20220131211935.3656-3-W_Armin@gmx.de
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Right now, when sch56xx-common has detected a SCH5627/SCH5636
superio chip, the corresponding module is not automatically
loaded.
Fix that by adding the necessary device tables to both modules.
Tested on a Fujitsu Esprimo P720.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20220131211935.3656-2-W_Armin@gmx.de
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The recent addition of the label attribute added some code that read the
"label" device property, without checking first that "dev" was non-NULL.
Fix this issue by first checking that "dev" is non-NULL.
Fixes: ccd98cba6a18 ("hwmon: Add "label" attribute")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds support for Lattice's POWR1014 power manager IC.
Read access to all the ADCs on the chip are supported through
the "hwmon" "sysfs" files.
The main differences of POWR1014 compared to POWR1220 are
amount of VMON input lines: 10 on POWR1014 and 12 lines on POWR1220 and
number of output control signals: 14 on POWR1014 and 20 on POWR1220.
Signed-off-by: Michael Shych <michaelsh@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20220118075611.10665-4-michaelsh@nvidia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reduce code by using devm_hwmon_device_register_with_groups() API by
devm_hwmon_device_register_with_info() API.
The motivation is to reduce code and to allow easy support for similar
devices by the same driver.
Signed-off-by: Michael Shych <michaelsh@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20220118075611.10665-3-michaelsh@nvidia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ASUS ROG STRIX B450-F GAMING II has support of the same WMI
monitoring method as ASUS ROG STRIX B450-F GAMING.
This commit adds "ASUS ROG STRIX B450-F GAMING II" to
the list of boards that can be monitored using ASUS WMI.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=204807
Signed-off-by: Denis Pauk <pauk.denis@gmail.com>
Tested-by: Aleksa Savic <savicaleksa83@gmail.com>
Link: https://lore.kernel.org/r/20220112214917.11662-1-pauk.denis@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Asus Prime X570-Pro motherboards have a T_Sensor header that can be
connected to an optional temperature probe.
Signed-off-by: Anthony DeRossi <ajderossi@gmail.com>
Link: https://lore.kernel.org/r/20220111051842.25634-1-ajderossi@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Asus PRIME B550-PLUS motherboards have got an nct6775 chip. Its resource
range is covered by the \AMW0.SHWM OpRegion, so the chip is unusable
when using SIO. However ASUS WMI access works.
Add PRIME B550-PLUS to the list of motherboards using ASUS WMI to read
data.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220110024712.753492-1-dmitry.baryshkov@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ASUS Pro B550M-C/PRIME B550M-A boards have got an nct6775 chip, but
by default there's no use of it because of resource conflict with WMI
method.
This commit adds "Pro B550M-C" and "PRIME B550M-A" to
the list of boards that can be monitored using ASUS WMI.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=204807
Signed-off-by: Denis Pauk <pauk.denis@gmail.com>
Tested-by: Gregory P. Smith <greg@krypto.org>
Tested-by: Joel Wirāmu <jwp@redhat.com>
Tested-by: Jonathan Farrugia <jonfarr87@gmail.com>
Link: https://lore.kernel.org/r/20220112215013.11694-1-pauk.denis@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If a label is defined in the device tree for this device add that
to the device specific attributes. This is useful for userspace to
be able to identify an individual device when multiple identical
chips are present in the system.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Link: https://lore.kernel.org/r/20220110182256.30763-3-paul@crapouillou.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These registers report CPU temperatures (and, depending on the system,
sometimes chipset temperatures) via the TSI interface on AMD systems.
They're distinct from most of the other Super-IO temperature readings
(CPUTIN, SYSTIN, etc.) in that they're not a selectable source for
monitoring and are in a different (higher resolution) format, but can
still provide useful temperature data.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Tested-by: Renze Nicolai <renze@rnplus.nl>
Link: https://lore.kernel.org/r/20220113164629.21924-1-zev@bewilderbeest.net
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
According to the March 2013 revision of the LM82 datasheet, the latest
LM82 die revision is 0x03. This was confirmed and observed with a real
chip. Further details in this revision of the LM82 datasheet suggest that
LM82 is now just a repackaged LM83. Such versions of LM82 will be detected
as LM83. Add comment to the code explaining why this may happen.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There should be no message in the kernel function if the detect function
fails to identify a chip; this is perfectly normal and does not warrant
a kernel log entry. Demote message to debug.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Using local caching in this driver had few benefits. It used cached values
for two seconds and then re-read all registers from the chip even if the
user only accessed a single attribute. On top of that, alarm attributes
were stale for up to four seconds (the first status register read reports
and clears an alarm, the second reports it cleared). Use regmap instead
for caching. Do not re-read non-volatile registers, and do not cache
volatile registers.
As part of this change, handle register read and write address differences
in regmap code. This is necessary to avoid problems with caching in the
regmap core, and ultimately simplifies the code.
Also, errors observed when reading from and writing to registers are no
longer ignored.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It has no value to name a variable 'new_client' in probe and detect
functions; it is obvious that the client is new. Use 'client' as
variable name instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There is no need to keep lm83_id at the end of the driver. Move it
forward to where it is needed to avoid a forward declaration.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Up to now udev events only report the affected hwmon device if an alert
is reported. This requires userspace to read all attributes if it wants
to know what triggered the event. Provide the attribute name with the
NAME property to help userspace find the attribute causing the event.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On PMBUS devices with multiple pages, the regulator ops need to be
protected with the update mutex. This prevents accidentally changing
the page in a separate thread while operating on the PMBUS_OPERATION
register.
Tested on Infineon xdpe11280 while a separate thread polls for sensor
data.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Link: https://lore.kernel.org/r/b991506bcbf665f7af185945f70bf9d5cf04637c.1645804976.git.sylv@sylv.io
Fixes: ddbb4db4ce ("hwmon: (pmbus) Add regulator support")
Cc: Alan Tull <atull@opensource.altera.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Almost all fault/warning bits in pmbus status registers remain set even
after fault/warning condition are removed. As per pmbus specification
these faults must be cleared by user.
Modify hwmon behavior to clear fault/warning bit after fetching data if
fault/warning bit was set. This allows to get fresh data in next read.
Signed-off-by: Vikash Chandola <vikash.chandola@linux.intel.com>
Link: https://lore.kernel.org/r/20220222131253.2426834-1-vikash.chandola@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If an attempt is made to a sensor with a thermal zone and it fails,
the call to devm_thermal_zone_of_sensor_register() may return -ENODEV.
This may result in crashes similar to the following.
Unable to handle kernel NULL pointer dereference at virtual address 00000000000003cd
...
Internal error: Oops: 96000021 [#1] PREEMPT SMP
...
pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : mutex_lock+0x18/0x60
lr : thermal_zone_device_update+0x40/0x2e0
sp : ffff800014c4fc60
x29: ffff800014c4fc60 x28: ffff365ee3f6e000 x27: ffffdde218426790
x26: ffff365ee3f6e000 x25: 0000000000000000 x24: ffff365ee3f6e000
x23: ffffdde218426870 x22: ffff365ee3f6e000 x21: 00000000000003cd
x20: ffff365ee8bf3308 x19: ffffffffffffffed x18: 0000000000000000
x17: ffffdde21842689c x16: ffffdde1cb7a0b7c x15: 0000000000000040
x14: ffffdde21a4889a0 x13: 0000000000000228 x12: 0000000000000000
x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000000
x8 : 0000000001120000 x7 : 0000000000000001 x6 : 0000000000000000
x5 : 0068000878e20f07 x4 : 0000000000000000 x3 : 00000000000003cd
x2 : ffff365ee3f6e000 x1 : 0000000000000000 x0 : 00000000000003cd
Call trace:
mutex_lock+0x18/0x60
hwmon_notify_event+0xfc/0x110
0xffffdde1cb7a0a90
0xffffdde1cb7a0b7c
irq_thread_fn+0x2c/0xa0
irq_thread+0x134/0x240
kthread+0x178/0x190
ret_from_fork+0x10/0x20
Code: d503201f d503201f d2800001 aa0103e4 (c8e47c02)
Jon Hunter reports that the exact call sequence is:
hwmon_notify_event()
--> hwmon_thermal_notify()
--> thermal_zone_device_update()
--> update_temperature()
--> mutex_lock()
The hwmon core needs to handle all errors returned from calls
to devm_thermal_zone_of_sensor_register(). If the call fails
with -ENODEV, report that the sensor was not attached to a
thermal zone but continue to register the hwmon device.
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Cc: Dmitry Osipenko <digetx@gmail.com>
Fixes: 1597b374af ("hwmon: Add notification support")
Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The sysfs does not like that we name the thermistor something
that contains a dash:
ntc-thermistor thermistor: hwmon: 'ssg1404-001221' is not a valid
name attribute, please fix
Fix it up by switching to an underscore.
Fixes: e13e979b2b ("hwmon: (ntc_thermistor) Add Samsung 1404-001221 NTC")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220205005804.123245-1-linus.walleij@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The value returned by an spi driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Claudius Heine <ch@denx.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220123175201.34839-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Add peci-dimmtemp driver for Temperature Sensor on DIMM readings that
are accessible via the processor PECI interface.
The main use case for the driver (and PECI interface) is out-of-band
management, where we're able to obtain thermal readings from an external
entity connected with PECI, e.g. BMC on server platforms.
Co-developed-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
Link: https://lore.kernel.org/r/20220208153639.255278-12-iwona.winiarska@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add peci-cputemp driver for Digital Thermal Sensor (DTS) thermal
readings of the processor package and processor cores that are
accessible via the PECI interface.
The main use case for the driver (and PECI interface) is out-of-band
management, where we're able to obtain the DTS readings from an external
entity connected with PECI, e.g. BMC on server platforms.
Co-developed-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
Link: https://lore.kernel.org/r/20220208153639.255278-11-iwona.winiarska@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a multi-function device to interface with the sy7636a
EPD PMIC chip from Silergy.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Paweł Marciniak reports the following crash, observed when clearing
the chassis intrusion alarm.
BUG: kernel NULL pointer dereference, address: 0000000000000028
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 3 PID: 4815 Comm: bash Tainted: G S 5.16.2-200.fc35.x86_64 #1
Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./Z97 Extreme4, BIOS P2.60A 05/03/2018
RIP: 0010:clear_caseopen+0x5a/0x120 [nct6775]
Code: 68 70 e8 e9 32 b1 e3 85 c0 0f 85 d2 00 00 00 48 83 7c 24 ...
RSP: 0018:ffffabcb02803dd8 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000002 RCX: 0000000000000000
RDX: ffff8e8808192880 RSI: 0000000000000000 RDI: ffff8e87c7509a68
RBP: 0000000000000000 R08: 0000000000000001 R09: 000000000000000a
R10: 000000000000000a R11: f000000000000000 R12: 000000000000001f
R13: ffff8e87c7509828 R14: ffff8e87c7509a68 R15: ffff8e88494527a0
FS: 00007f4db9151740(0000) GS:ffff8e8ebfec0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000028 CR3: 0000000166b66001 CR4: 00000000001706e0
Call Trace:
<TASK>
kernfs_fop_write_iter+0x11c/0x1b0
new_sync_write+0x10b/0x180
vfs_write+0x209/0x2a0
ksys_write+0x4f/0xc0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
The problem is that the device passed to clear_caseopen() is the hwmon
device, not the platform device, and the platform data is not set in the
hwmon device. Store the pointer to sio_data in struct nct6775_data and
get if from there if needed.
Fixes: 2e7b988696 ("hwmon: (nct6775) Use superio_*() function pointers in sio_data.")
Cc: Denis Pauk <pauk.denis@gmail.com>
Cc: Bernhard Seibold <mail@bernhard-seibold.de>
Reported-by: Paweł Marciniak <pmarciniak@lodz.home.pl>
Tested-by: Denis Pauk <pauk.denis@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
