Problem:
pch_udc continues operation even if VBUS becomes Low.
pch_udc performs D+ pulling up before VBUS becomes High.
USB device should be controlled according to VBUS state.
Root cause:
The current pch_udc is not always monitoring VBUS.
Solution:
The change of VBUS is detected using an interrupt of GPIO.
If VBUS became Low, pch_udc handles 'disconnect'.
After VBUS became High, a pull improves D+, and pch_udc
handles 'connect'.
[ balbi@ti.com : make it actually compile ]
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Problem:
In USB Suspend, pch_udc handles 'disconnect'.
Root cause:
The current pch_udc is not monitoring VBUS.
When USB cable is disconnected, USB Device Controller generates
an interrupt of USB Suspend.
pch_udc cannot distinguish it is USB Suspend or disconnect.
Therefore, pch_udc handles 'disconnect' after an interrupt of
USB Suspend happend.
Solution:
VBUS is detected through GPIO.
After an interrupt produced USB Suspend, if VBUS is Low,
pch_udc handles 'disconnect'.
If VBUS is High, pch_udc handles 'suspend'.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
_ep to ep is a pointer substraction so ep won't be zero unless _ep was
8. This was not intendent by the author, it was probably a typo while
checking for NULL of the argument.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If the stream check fails then we leave ep->desc assigend but we return
with an error code. The caller assumes the endpoint is not enabled
(which is the case) but it can not enable it again due to this
assigment.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Following removal announce and addition to feature-removal-schedule.txt,
here is the actual source code deletion for Atmel CAP9 family.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add IAD to bind the two interfaces of ECM so that it works properly
in composite gadget mode.
Signed-off-by: Thirupathi <thirupathi.chippakurthy@stericsson.com>
Signed-off-by: Praveena Nadahally <praveen.nadahally@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ab943a2e12 (USB: gadget: gadget zero uses new suspend/resume hooks)
introduced a copy-paste error where f_loopback.c writes to a variable
declared in f_sourcesink.c. This prevents one from creating gadgets
that only have a loopback function.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Timo Juhani Lindfors <timo.lindfors@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix the following build warnings:
CC [M] drivers/usb/gadget/acm_ms.o
drivers/usb/gadget/acm_ms.c: In function ‘__check_ro’:
drivers/usb/gadget/acm_ms.c:119: warning: return from incompatible pointer type
drivers/usb/gadget/acm_ms.c: In function ‘__check_removable’:
drivers/usb/gadget/acm_ms.c:119: warning: return from incompatible pointer type
drivers/usb/gadget/acm_ms.c: In function ‘__check_cdrom’:
drivers/usb/gadget/acm_ms.c:119: warning: return from incompatible pointer type
drivers/usb/gadget/acm_ms.c: In function ‘__check_nofua’:
drivers/usb/gadget/acm_ms.c:119: warning: return from incompatible pointer type
drivers/usb/gadget/acm_ms.c: In function ‘__check_stall’:
drivers/usb/gadget/acm_ms.c:119: warning: return from incompatible pointer type
CC [M] drivers/usb/gadget/mass_storage.o
drivers/usb/gadget/mass_storage.c: In function ‘__check_ro’:
drivers/usb/gadget/mass_storage.c:94: warning: return from incompatible pointer type
drivers/usb/gadget/mass_storage.c: In function ‘__check_removable’:
drivers/usb/gadget/mass_storage.c:94: warning: return from incompatible pointer type
drivers/usb/gadget/mass_storage.c: In function ‘__check_cdrom’:
drivers/usb/gadget/mass_storage.c:94: warning: return from incompatible pointer type
drivers/usb/gadget/mass_storage.c: In function ‘__check_nofua’:
drivers/usb/gadget/mass_storage.c:94: warning: return from incompatible pointer type
drivers/usb/gadget/mass_storage.c: In function ‘__check_stall’:
drivers/usb/gadget/mass_storage.c:94: warning: return from incompatible pointer type
Declare the fsg_module_parameters fields as "bool" so that they can match the types
passed in FSG_MODULE_PARAM_ARRAY macro.
Since commit 493c90ef (module_param: check that bool parameters really are bool.),
moduleparam.h was changed in a way that the "bool" parameter type now really
requires "bool" type and no longer allows "unsigned int".
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Currently the UASP gadget fails to bind on an UDC which does not provide
stream support. This is true for all udc in tree except for dummy and
dwc3 since they don't support SuperSpeed.
There is no need to test for the availability of stream support on those
UDCs because we will never even try to use them. I think it is sane to
assume that StreamSupport is always available on SuperSpeed since it is
one of the key features.
The host side will only allocate on SS so this part is also fine.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The max_ep is the number of endpoint * 2.
But in dtd_complete_irq, it does again * 2, it will deference wrong memory
after scanning max_ep - 1.
The another similar problem is at USB_REQ_SET_FEATURE (the pipe number
should be 0 and max_ep - 1).
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Matthieu castet <matthieu.castet@parrot.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
SuperSpeed Isoc endpoints also use the bMaxBurst value from the
companion descriptor. See section 9.6.7 in the USB 3.0 spec.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
UDC core will call disconnect() and unbind() for us upon the gadget
removal, so we should not do it ourselves. Otherwise, a composite
gadget will explode, for example. Others might too.
This was introduced during conversion to new style gadget in 2c7f0989
(usb: gadget: langwell: convert to new style).
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: stable@vger.kernel.org # v3.2
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since there is no working (or even compilable) OTG_TRANSCEIVER support
for this driver, remove the dead code which depends on it at compile
time.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: stable@vger.kernel.org # v2.6.31+
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove one define of FSG_NO_INTR_EP and we still have that we can use.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The m.nazarewicz@samsung.com email address is no longer valid,
so this commit replaces it with mina86@mina86.com which is
employer-agnostic and thus should be valid for foreseeable
feature.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch makes use of usb_endpoint_type() instead of the open coding.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dummy_hcd provides (alloc|free)_stream() callbacks but there are not
doing anything. The transfer side also lacks matching of streams. This
patch changes this and implements stream allocation / de-allocation
support and proper urb <=> req matching.
The UDC side exposes a limit of 16 streams. DWC3, the only USB3 UDC has
no limitations in this regard except that it _needs_ to know that
streams will be used at the ep_enable time. At the host side, there is
no real limit either: XHCI can allocate any number of streams as long as
it does not run out of memory. The UAS gadget currently requests 16
streams and the UAS host side fallbacks from the requested 256 down to
16 which is fine.
From the UASP point of view (the only specified user), the number of
used streams does not really matter. The only limitation is that the
host may not use a higher stream than the gadget requested and can deal
with.
The dummy stream support has been modelled after current UAS + XHCI +
DWC3 + UASP usage which helps me testing:
- the device announces that each ep supports 16 streams (even it could
more than that).
- the device side looks into Companion descriptor at ep_enable time and
enables them according to it.
- the host side tries to enable the requested number of streams but the
upper limit is the Comanion descriptor. None (zero streams) is an
error condition, less is okay.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ISSUE:
Adding debugging messages.
CAUSE:
The debugging messages are added to make sure of that major interrupt events
are occurring.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ISSUE:
USB Suspend interrupts occur frequently.
CAUSE:
When it is called pch_udc_reconnect() in USB Suspend, it repeats reset and
Suspend.
SOLUTION:
pch_udc_reconnect() does not enable all interrupts. When an enumeration event
occurred the driver enables all interrupts.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ISSUE:
After a USB cable is connect/disconnected, the system rarely freezes.
CAUSE:
Since the USB device controller cannot know to disconnect the USB cable, when
it is used without detecting VBUS by GPIO, the UDC driver does not notify to
USB Gadget.
Since USB Gadget cannot know to disconnect, a false setting occurred when the
USB cable is connected/disconnect repeatedly.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ISSUE:
After USB Suspend, a system rarely freezes.
CAUSE:
When USB Suspend occurred, the driver is not notifying
a gadget of the event.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ISSUE:
If the return value of pch_udc_pcd_init() is False, the return value of
this function is unsettled.
Since pch_udc_pcd_init() always returns 0, there is not actually the issue.
CAUSE:
If pch_udc_pcd_init() is True, the variable, retval, is not set for an
appropriate value.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ISSUE:
When the driver notifies a gadget of a disconnect event, a system
rarely freezes.
CAUSE:
When the driver calls dev->driver->disconnect(), it is not calling
spin_unlock().
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This will enable the system to check for activity of the usb gadget
and also in a later patch to control the usbphy power-domain.
When handling the power domain there, it will be possible to remove
another reference to architecture code.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The helper functions were definied but never used until now.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We've dereferenced req already, and we checked for bogus parameters at
the start of the function.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is no reason why dummy_alloc_streams() and dummy_free_streams()
are global. Make them static instead.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This renames a function so "update" is spelled properly.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds sg support to dummy_hcd. It seems that uas is not able
to work with a hcd which does not support sg only based transfers.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch moves the part of the code which does the bare transfer into
its function. It is a preparion for the implementation of sg support.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
While playing with uasp I noticed that it does not work with dummy_hcd.
The problem is that uasp requires a stream capable endpoint which it is
requesting at bind time like every other gadget. dummy_hcd however
initializes the max_stream value after connect once it knows if it runs
at SS or not.
I don't think that it is might be wrong to initialize the stream
capability even at HS speed. The gadget may not use this descriptor at
HS speed so it should not cause any damage.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cleanup patches for various ARM platforms and some of their associated
drivers, the bulk of these is for mach-91.
I ended up pulling in the restart branch from Russell in order to
fix up some simple but annoying merge conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=9q+1
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Cleanups on various subarchitectures
Cleanup patches for various ARM platforms and some of their associated
drivers, the bulk of these is for mach-91.
Arnd ended up pulling in the restart branch from Russell in order to
fix up some simple but annoying merge conflicts.
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
arm/at91: fix build of stamp9g20
ARM: u300: delete memory.h
MAINTAINERS: add maintainer entry for Picochip picoxcell
ARM: picoxcell: move io mappings to common.c
ARM: picoxcell: don't reserve irq_descs
ARM: picoxcell: remove mach/memory.h
ARM: at91: delete the pcontrol_g20_defconfig
arm/tegra: Remove code that's ifndef CONFIG_ARM_GIC
arm/tegra: remove unused defines
arm/tegra: fix variable formatting in makefile
ARM: davinci: vpif: move code to driver core header from platform
ARM: at91/gpio: fix display of number of irq setuped
ARM: at91/gpio: drop PIN_BASE
ARM: at91/udc: use gpio_is_valid to check the gpio
ARM: at91/ohci: use gpio_is_valid to check the gpio
ARM: at91/nand: use gpio_is_valid to check the gpio
ARM: at91/mmc: use gpio_is_valid to check the gpio
ARM: at91/ide: use gpio_is_valid to check the gpio
ARM: at91/pata: use gpio_is_valid to check the gpio
ARM: at91/soc: use gpio_is_valid to check the gpio
...
* if you do dput() of root dentry, do *not* follow that with iput() of root
inode.
* while we are at it, don't do that dput() at all - you are leaving the pointer
in ->s_root and your ->kill_sb() will be very unhappy with that. It will do
proper dput(), though, so the easiest way is to leave that to it entirely.
* freeing ->s_fs_info is also best left to ->kill_sb() (which will do it
anyway), especially since we leave the pointer in place.
* that xchg() in ->kill_sb() is not a bug per se, but it's a plain and simple
masturbation with fewer excuses than Onan had...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (53 commits)
Kconfig: acpi: Fix typo in comment.
misc latin1 to utf8 conversions
devres: Fix a typo in devm_kfree comment
btrfs: free-space-cache.c: remove extra semicolon.
fat: Spelling s/obsolate/obsolete/g
SCSI, pmcraid: Fix spelling error in a pmcraid_err() call
tools/power turbostat: update fields in manpage
mac80211: drop spelling fix
types.h: fix comment spelling for 'architectures'
typo fixes: aera -> area, exntension -> extension
devices.txt: Fix typo of 'VMware'.
sis900: Fix enum typo 'sis900_rx_bufer_status'
decompress_bunzip2: remove invalid vi modeline
treewide: Fix comment and string typo 'bufer'
hyper-v: Update MAINTAINERS
treewide: Fix typos in various parts of the kernel, and fix some comments.
clockevents: drop unknown Kconfig symbol GENERIC_CLOCKEVENTS_MIGR
gpio: Kconfig: drop unknown symbol 'CS5535_GPIO'
leds: Kconfig: Fix typo 'D2NET_V2'
sound: Kconfig: drop unknown symbol ARCH_CLPS7500
...
Fix up trivial conflicts in arch/powerpc/platforms/40x/Kconfig (some new
kconfig additions, close to removed commented-out old ones)
Conflicts:
arch/arm/mach-at91/at91cap9.c
arch/arm/mach-at91/at91sam9260.c
arch/arm/mach-at91/at91sam9261.c
arch/arm/mach-at91/at91sam9263.c
arch/arm/mach-at91/at91sam9g45.c
arch/arm/mach-at91/at91sam9rl.c
arch/arm/mach-exynos/cpu.c
arch/arm/mach-shmobile/board-kota2.c
This resolves a bunch of conflicts between the arm-soc tree
and changes from the arm tree that have gone upstream.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
net/bluetooth/l2cap_core.c
Just two overlapping changes, one added an initialization of
a local variable, and another change added a new local variable.
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead use container_of to retrieve the s3c_hsudc from the
struct usb_gadget pointer.
[ balbi@ti.com : changed verbose container_of() into
an already provided helper 'to_hsudc()' ]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As the memory region is requested through request_mem_region
use the correct paired method to release it in the error path
and don't go "beneath the API".
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The udc has three supplies: vdda (3.3V), vddi (1.2V) and vddosc (1.8-3.3V).
Turn these on and off on start and stop calls.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
udc_start and udc_stop reduce code duplication in comparison to
start and stop generalising calls done by all drivers
(i.e. bind and unbind) and moving these calls to common code.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Instead of adding and deleting the gadget device in the start and stop
invocations. Use device_register in the probe method to initialize
and add the gadget device.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Gadget drivers should be compilable on all architectures.
This patch removes one dependency on architecture-specific code.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch do the following things:
1. Change the Kconfig information.
2. Rename the driver name.
3. Don't do any type cast to io memory.
4. Add dummy stub for clk framework.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to ChipIdea's SPEC, we cannot touch curr_dtd_ptr in dqh
directly, use prime endpoint instead.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We should not change gadget driver's descriptors just
because we think it's right to do so.
There are several of reasons which would support this
statement but it suffices to say that this was probably
never tested because it updates bmAttributes without
asking the driver if it's ok to do so.
This means that e.g. on UASP gadget it would enable
stream support even for the command endpoint which must
not have stream support enabled.
In fact, this change is fixing the bug introduced by
commit a59d6b9 (usb: gadget: add streams support to
the gadget framework) which was caught when testing
UASP gadget with dwc3 driver.
Cc: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Rewrite function queue_dtd according to ChipIdea's reference manual.
Remove all unnecessary logic, it will enhance the performance.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Release superspeed mass storage descriptors memory
when the function is unbind.
Signed-off-by: Yu Xu <yuxu@marvell.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch impletments system suspend/resume functions for Marvell
otg controller.
If OTG is enabled, OTG driver will do most of the work.
If not, we will check clock gating.
If clock gating is enabled, the UDC will be start/stop automatically.
If not, UDC will be start/stop in suspend/resume functions.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Split the clock relative code from clock gating solution.
Then we can remove some duplicate code, make the code more clean.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When device is stopped, there is no need to handle ISR.
Especially when otg switch to HOST mode.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add otg relative code, make it possible to switch between host and
device.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The advantage of kcalloc is, that will prevent integer overflows which could
result from the multiplication of number of elements and size and it is also
a bit nicer to read.
The semantic patch that makes this change is available
in https://lkml.org/lkml/2011/11/25/107
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: Michal Nazarewicz <[4]mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This commit renames the “speed” field of the usb_gadget_driver
structure to “max_speed”. This is so that to make it more
apparent that the field represents the maximum speed gadget
driver can support.
This also make the field look more like fields with the same
name in usb_gadget and usb_composite_driver structures. All
of those represent the *maximal* speed given entity supports.
After this commit, there are the following fields in various
structures:
* usb_gadget::speed - the current connection speed,
* usb_gadget::max_speed - maximal speed UDC supports,
* usb_gadget_driver::max_speed - maximal speed gadget driver
supports, and
* usb_composite_driver::max_speed - maximal speed composite
gadget supports.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This commit replaces usb_gadget's is_dualspeed field with
a max_speed field.
[ balbi@ti.com : Fixed DWC3 driver ]
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
With Peiyu's patch "gadget: mass_storage: adapt logic block size to bound block
devices" (http://www.spinics.net/lists/linux-usb/msg50791.html), now mass storage
can adjust logic block size dynamically based on real devices.
Then there is one issue caused by it, if two luns have different logic block size,
mass storage can't work.
Let's check the current software flow:
1. get_next_command(): call received_cbw();
2. received_cbw(): update common->lun = cbw->Lun, but common->curlen is not updated;
3. do_scsi_command(): in READ_X and WRITE_X commands, common->data_size_from_cmnd is
updated by common->curlun->blkbits;
4. check_command(): update common->curlun according to common->lun
As you can see, the step 3 uses wrong common->curlun, then wrong common->curlun->blkbits.
If the two luns have same blkbits, there isn't issue. Otherwise, both will fail.
This patch moves the common->curlun update to step 1, then make sure step 3 gets right
blkbits and data_size_from_cmnd.
Cc: Peiyu Li <peiyu.li@csr.com>
Signed-off-by: YuPing Luo <yuping.luo@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The ci13xxx_udc driver checks the number of endpoints in the udc
controller, however some routines expect that the hardware has 16
bidirectional endpoints.
This patch improves the driver to work on controllers with less than
16 endpoints like the udc controller found on freescale's
mx23 and mx28.
Tested-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some gadget drivers don't implement suspend and/or resume functions.
Instead of changing the gadget drivers, make suspend and resume in
ci13xxx_udc (following other udc drivers) optional.
Tested-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The original implementation of dequeuing a request in progress
is not correct. Change to use a correct process and also clean
up the related functions a little bit.
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In order to support multiple SoC kernel image, compile-time dependency
on a specific SoC type should be avoided.
fsl_udc_clk_finalize is already protected by cpu_is_mx35(), so remove
the compile-time check for CONFIG_SOC_IMX35.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following build error:
CC [M] drivers/usb/gadget/fsl_mxc_udc.o
drivers/usb/gadget/fsl_mxc_udc.c: In function 'fsl_udc_clk_finalize':
drivers/usb/gadget/fsl_mxc_udc.c:98: error: implicit declaration of function 'readl'
drivers/usb/gadget/fsl_mxc_udc.c💯 error: implicit declaration of function 'writel'
This error is caused by the follwing commit:
(16fcb63: arm/imx: remove mx31_setup_weimcs( ) from mx31.h)
,which removed '#include <linux/io.h>' from mx31.h.
fsl_mxc_udc.c includes <mach/hardware.h>, which in turns includes mx31.h, so
that's the reason fsl_mxc_udc.c built fine previously.
Instead of relying on the indirect inclusion of the linux/io.h header file,
include it directly in fsl_mxc_udc.c.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some ISO gadgets, like audio, has SYNC attribute as well as
USB_ENDPOINT_XFER_ISOC for their bmAttributes at ISO endpoint
descriptor. So, it needs to use usb_endpoint_xfer_isoc to judge
ISO XFER.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Several UDC drivers had a gadget driver's speed sanity check of the
form of:
driver->speed != USB_SPEED_HIGH
or:
driver->speed != USB_SPEED_HIGH && driver->speed != USB_SPEED_FULL
As more and more gadget drivers support USB SuperSpeed, driver->speed
may be set to USB_SPEED_SUPER and UDC driver should handle such gadget
correctly. The above checks however fail to recognise USB_SPEED_SUPER
as a valid speed.
This commit changes the two checks to:
driver->speed < USB_SPEED_HIGH
or:
driver->speed < USB_SPEED_FULL
respectively.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit "usb: gadget: use config_ep_by_speed() instead of
ep_choose()" broke g_serial in "non ACM nor OBEX"
mode. Apply a trivial fix on usb endpoints discovery.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts the drivers in drivers/usb/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This pulls in the latest USB bugfixes and helps a few of the drivers
merge nicer in the future due to changes in both branches.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Given we dont use anymore the struct net_device *dev argument, and this
interface brings litle benefit, remove netdev_{alloc|free}_page(), to
debloat include/linux/skbuff.h a bit.
(Some drivers used a mix of these interfaces and alloc_pages())
When allocating a page given to device for DMA transfer (device to
memory), it makes sense to use a cold one (__GFP_COLD)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (48 commits)
USB: Fix Corruption issue in USB ftdi driver ftdi_sio.c
USB: option: add PID of Huawei E173s 3G modem
OHCI: final fix for NVIDIA problems (I hope)
USB: option: release new PID for ZTE 3G modem
usb: Netlogic: Fix HC_LENGTH call in ehci-xls.c
USB: storage: ene_ub6250: fix compile warnings
USB: option: add id for 3G dongle Model VT1000 of Viettel
USB: serial: pl2303: rm duplicate id
USB: pch_udc: Change company name OKI SEMICONDUCTOR to LAPIS Semiconductor
USB: pch_udc: Support new device LAPIS Semiconductor ML7831 IOH
usb-storage: Accept 8020i-protocol commands longer than 12 bytes
USB: quirks: adding more quirky webcams to avoid squeaky audio
powerpc/usb: fix type cast for address of ioremap to compatible with 64-bit
USB: at91: at91-ohci: fix set/get power
USB: cdc-acm: Fix disconnect() vs close() race
USB: add quirk for Logitech C600 web cam
USB: EHCI: fix HUB TT scheduling issue with iso transfer
USB: XHCI: resume root hubs when the controller resumes
USB: workaround for bug in old version of GCC
USB: ark3116 initialisation fix
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (86 commits)
ipv4: fix redirect handling
ping: dont increment ICMP_MIB_INERRORS
sky2: fix hang in napi_disable
sky2: enforce minimum ring size
bonding: Don't allow mode change via sysfs with slaves present
f_phonet: fix page offset of first received fragment
stmmac: fix pm functions avoiding sleep on spinlock
stmmac: remove spin_lock in stmmac_ioctl.
stmmac: parameters auto-tuning through HW cap reg
stmmac: fix advertising 1000Base capabilties for non GMII iface
stmmac: use mdelay on timeout of sw reset
sky2: version 1.30
sky2: used fixed RSS key
sky2: reduce default Tx ring size
sky2: rename up/down functions
sky2: pci posting issues
sky2: fix hang on shutdown (and other irq issues)
r6040: fix check against MCRO_HASHEN bit in r6040_multicast_list
MAINTAINERS: change email address for shemminger
pch_gbe: Move #include of module.h
...
This patch (as1502) removes the UTF8-to-UTF16 conversion routine in
the USB gadget library and replaces it with a call to the equivalent
function in the NLS library.
The only downside worth noting is that the NLS library routine
requires the output buffer to be 16-bit aligned. This is always true
in the gadget code, because the output buffer is always a
usb_request buffer being used to send a string descriptor.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We pull one byte (the MAC header) from the first fragment before the
fragment is actually appended. So the socket buffer length is 1, not 0.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On October 1 in 2011,
OKI SEMICONDUCTOR Co., Ltd. changed the company name in to LAPIS Semiconductor Co., Ltd.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Below are codes for accessing usb sysif_regs in driver:
usb_sys_regs = (struct usb_sys_interface *)
((u32)dr_regs + USB_DR_SYS_OFFSET);
these codes work in 32-bit, but in 64-bit, use u32 to type cast the address
of ioremap is not right, and accessing members of 'usb_sys_regs' will cause
call trace, so use (void *) for both 32-bit and 64-bit.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since commit "193ab2a usb: gadget: allow multiple gadgets to be built"
the udc controllers can be compiled as a module. The ci13xxx_msm driver
is missing the MODULE_LICENSE statement, so loading fails with:
ci13xxx_msm: module license 'unspecified' taints kernel.
ci13xxx_msm: Unknown symbol dev_set_name (err 0)
ci13xxx_msm: Unknown symbol platform_get_irq (err 0)
ci13xxx_msm: Unknown symbol device_unregister (err 0)
ci13xxx_msm: Unknown symbol usb_add_gadget_udc (err 0)
ci13xxx_msm: Unknown symbol put_device (err 0)
ci13xxx_msm: Unknown symbol platform_driver_register (err 0)
ci13xxx_msm: Unknown symbol platform_get_resource (err 0)
ci13xxx_msm: Unknown symbol device_register (err 0)
ci13xxx_msm: Unknown symbol usb_del_gadget_udc (err 0)
This patch adds the missing MODULE_LICENSE statement with GPL v2 according
to the header of the driver.
Tested-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the following compile errors that show up if switching
on the debug trace code:
drivers/usb/gadget/ci13xxx_udc.c: In function 'ci13xxx_wakeup':
drivers/usb/gadget/ci13xxx_udc.c:2517:3: error: 'dev' undeclared (first use in this function)
drivers/usb/gadget/ci13xxx_udc.c:2517:3: note: each undeclared identifier is reported only once for each function it appears in
drivers/usb/gadget/ci13xxx_udc.c: In function 'udc_probe':
drivers/usb/gadget/ci13xxx_udc.c:2867:2: error: 'name' undeclared (first use in this function)
Tested-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The inline documentation of _gadget_stop_activity() states that the
function should be called holding the udc->lock. This however will
result in a deadlock, because _gadget_stop_activity() takes the udc->lock.
During normal operation _gadget_stop_activity() is always called unlocked,
but in ci13xxx_stop() it's called locked, this results in the following
deadlock during rmmod of a gadget driver.
This patch fixes the deadlock by calling _gadget_stop_activity() always
unlocked, the inline documentation is adjusted accordingly.
=============================================
[ INFO: possible recursive locking detected ]
3.1.0-rc6+ #159
---------------------------------------------
rmmod/121 is trying to acquire lock:
(udc_lock){-.-...}, at: [<c0229048>] _gadget_stop_activity+0x18/0x154
but task is already holding lock:
(udc_lock){-.-...}, at: [<c02291e0>] ci13xxx_stop+0x5c/0x164
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(udc_lock);
lock(udc_lock);
*** DEADLOCK ***
May be due to missing lock nesting notation
2 locks held by rmmod/121:
#0: (udc_lock#2){+.+.+.}, at: [<c02286c0>] usb_gadget_unregister_driver+0x34/0x88
#1: (udc_lock){-.-...}, at: [<c02291e0>] ci13xxx_stop+0x5c/0x164
stack backtrace:
[<c000d41c>] (unwind_backtrace+0x0/0xf0) from [<c0056f94>] (check_deadlock.clone.24+0x284/0x2c4)
[<c0056f94>] (check_deadlock.clone.24+0x284/0x2c4) from [<c00589ac>] (validate_chain.clone.25+0x430/0x6fc)
[<c00589ac>] (validate_chain.clone.25+0x430/0x6fc) from [<c0059bac>] (__lock_acquire+0x494/0x8f0)
[<c0059bac>] (__lock_acquire+0x494/0x8f0) from [<c005a698>] (lock_acquire+0x98/0x1a8)
[<c005a698>] (lock_acquire+0x98/0x1a8) from [<c02f12a4>] (_raw_spin_lock_irqsave+0x64/0xa0)
[<c02f12a4>] (_raw_spin_lock_irqsave+0x64/0xa0) from [<c0229048>] (_gadget_stop_activity+0x18/0x154)
[<c0229048>] (_gadget_stop_activity+0x18/0x154) from [<c0229234>] (ci13xxx_stop+0xb0/0x164)
[<c0229234>] (ci13xxx_stop+0xb0/0x164) from [<c022867c>] (usb_gadget_remove_driver+0x88/0x98)
[<c022867c>] (usb_gadget_remove_driver+0x88/0x98) from [<c02286f4>] (usb_gadget_unregister_driver+0x68/0x88)
[<c02286f4>] (usb_gadget_unregister_driver+0x68/0x88) from [<c0065f2c>] (sys_delete_module+0x1fc/0x26c)
[<c0065f2c>] (sys_delete_module+0x1fc/0x26c) from [<c00092a0>] (ret_fast_syscall+0x0/0x38)
BUG: spinlock lockup on CPU#0, rmmod/121, c05b1644
[<c000d41c>] (unwind_backtrace+0x0/0xf0) from [<c01da000>] (do_raw_spin_lock+0x128/0x144)
[<c01da000>] (do_raw_spin_lock+0x128/0x144) from [<c02f12c8>] (_raw_spin_lock_irqsave+0x88/0xa0)
[<c02f12c8>] (_raw_spin_lock_irqsave+0x88/0xa0) from [<c0229048>] (_gadget_stop_activity+0x18/0x154)
[<c0229048>] (_gadget_stop_activity+0x18/0x154) from [<c0229234>] (ci13xxx_stop+0xb0/0x164)
[<c0229234>] (ci13xxx_stop+0xb0/0x164) from [<c022867c>] (usb_gadget_remove_driver+0x88/0x98)
[<c022867c>] (usb_gadget_remove_driver+0x88/0x98) from [<c02286f4>] (usb_gadget_unregister_driver+0x68/0x88)
[<c02286f4>] (usb_gadget_unregister_driver+0x68/0x88) from [<c0065f2c>] (sys_delete_module+0x1fc/0x26c)
[<c0065f2c>] (sys_delete_module+0x1fc/0x26c) from [<c00092a0>] (ret_fast_syscall+0x0/0x38)
Tested-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current driver sets the request's dma addr (mReq->req.dma) to 0 to
mark the DMA address as not valid. However some gadget drivers
(e.g. gadgetfs) set the request's dma addr to DMA_ADDR_INVALID to mark
the address as invalid. This leads to bogus data send because the
ci13xxx_udc driver assumes the request has already been mapped.
This patch fixes the problem, by using DMA_ADDR_INVALID instead of 0
to mark the request's DMA address as invalid.
Tested-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Under certain circumstances lockdep finds an inconsistent lock state in
gadgetfs. The problem can be reproduced with a hardware using the
ci13xxx_udc driver and the gadgetfs test program (needs a patch to support
the ci13xxx_udc, though):
http://www.linux-usb.org/gadget/usb.c
Start the test program, wait to initialize, then press Ctrl+c.
This patch fixes the following problem by using spin_lock_irqsave()
instead of spin_lock().
=================================
[ INFO: inconsistent lock state ]
3.1.0-rc6+ #158
---------------------------------
inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
usb/113 [HC0[0]:SC0[0]:HE1:SE1] takes:
(&(&dev->lock)->rlock){?.....}, at: [<bf000340>] gadgetfs_disconnect+0x14/0x80 [gadgetfs]
{IN-HARDIRQ-W} state was registered at:
[<c00596b8>] mark_irqflags+0x14c/0x1ac
[<c0059bf8>] __lock_acquire+0x4e0/0x8f0
[<c005a698>] lock_acquire+0x98/0x1a8
[<c02f10e0>] _raw_spin_lock+0x54/0x8c
[<bf000340>] gadgetfs_disconnect+0x14/0x80 [gadgetfs]
[<c0229104>] _gadget_stop_activity+0xd4/0x154
[<c022b130>] isr_reset_handler+0x34/0x1c0
[<c022c320>] udc_irq+0x204/0x228
[<c0069018>] handle_irq_event_percpu+0x64/0x3a0
[<c0069390>] handle_irq_event+0x3c/0x5c
[<c006ae5c>] handle_level_irq+0x8c/0x10c
[<c0068a34>] generic_handle_irq+0x30/0x44
[<c0009b2c>] handle_IRQ+0x30/0x84
[<c0008ef8>] __irq_svc+0x38/0x60
[<c0009c58>] default_idle+0x30/0x34
[<c0009e30>] cpu_idle+0x9c/0xd8
[<c04056f4>] start_kernel+0x278/0x2bc
irq event stamp: 6412
hardirqs last enabled at (6412): [<c02f1cd0>] _raw_spin_unlock_irqrestore+0x30/0x5c
hardirqs last disabled at (6411): [<c02f1278>] _raw_spin_lock_irqsave+0x20/0xa0
softirqs last enabled at (6381): [<c002833c>] irq_exit+0xa0/0xa8
softirqs last disabled at (6372): [<c002833c>] irq_exit+0xa0/0xa8
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&dev->lock)->rlock);
<Interrupt>
lock(&(&dev->lock)->rlock);
*** DEADLOCK ***
1 lock held by usb/113:
#0: (udc_lock#2){+.+.+.}, at: [<c02286c0>] usb_gadget_unregister_driver+0x34/0x88
stack backtrace:
[<c000d41c>] (unwind_backtrace+0x0/0xf0) from [<c0058e98>] (print_usage_bug+0x144/0x1c4)
[<c0058e98>] (print_usage_bug+0x144/0x1c4) from [<c0059144>] (mark_lock_irq+0x22c/0x274)
[<c0059144>] (mark_lock_irq+0x22c/0x274) from [<c00592d4>] (mark_lock+0x148/0x3e0)
[<c00592d4>] (mark_lock+0x148/0x3e0) from [<c0059668>] (mark_irqflags+0xfc/0x1ac)
[<c0059668>] (mark_irqflags+0xfc/0x1ac) from [<c0059bf8>] (__lock_acquire+0x4e0/0x8f0)
[<c0059bf8>] (__lock_acquire+0x4e0/0x8f0) from [<c005a698>] (lock_acquire+0x98/0x1a8)
[<c005a698>] (lock_acquire+0x98/0x1a8) from [<c02f10e0>] (_raw_spin_lock+0x54/0x8c)
[<c02f10e0>] (_raw_spin_lock+0x54/0x8c) from [<bf000340>] (gadgetfs_disconnect+0x14/0x80 [gadgetfs])
[<bf000340>] (gadgetfs_disconnect+0x14/0x80 [gadgetfs]) from [<c0229104>] (_gadget_stop_activity+0xd4/0x154)
[<c0229104>] (_gadget_stop_activity+0xd4/0x154) from [<c0229240>] (ci13xxx_stop+0xbc/0x17c)
[<c0229240>] (ci13xxx_stop+0xbc/0x17c) from [<c022867c>] (usb_gadget_remove_driver+0x88/0x98)
[<c022867c>] (usb_gadget_remove_driver+0x88/0x98) from [<c02286f4>] (usb_gadget_unregister_driver+0x68/0x88)
[<c02286f4>] (usb_gadget_unregister_driver+0x68/0x88) from [<bf0003e8>] (dev_release+0x14/0x48 [gadgetfs])
[<bf0003e8>] (dev_release+0x14/0x48 [gadgetfs]) from [<c00cc158>] (__fput+0xa4/0x1f0)
[<c00cc158>] (__fput+0xa4/0x1f0) from [<c00c7f28>] (filp_close+0x5c/0x74)
[<c00c7f28>] (filp_close+0x5c/0x74) from [<c00c7fe8>] (sys_close+0xa8/0x150)
[<c00c7fe8>] (sys_close+0xa8/0x150) from [<c00092a0>] (ret_fast_syscall+0x0/0x38)
Tested-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The dynamic jack allocation of the MIDI gadget currently links all
external jacks to one single instance of an embedded jack. According to
the spec, this is only valid if these streams always carry the same data
stream, as described in the USB MIDI 1.0 spec, chapter 3.3.1.
Also, genius Windows 7(tm) terminates it's life cycle instantly with a
blue screen of death once a device with more than one input and output
port with the current implementation is connected.
While at it, and because it grew again by this change, allocate the
temporary function pointer list on the heap, not on the stack.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB-IF CV compliance tester is getting stricter, and it would
be valid for it to fail a mass-storage device that accepts an
invalid USB_BULK_RESET_REQUEST request. Although it doesn't do
that yet, let's be proactive and fix that now.
Suggested by Alan Stern.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The latest USB-IF CV tester checks for a valid length for this
request.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix compile error in file drivers/usb/gadget/fsl_udc_core.c.
drivers/usb/gadget/fsl_udc_core.c: In function 'portscx_device_speed':
drivers/usb/gadget/fsl_udc_core.c:1720: error: 'speed' undeclared (first
use in this function)
Introduced in commit e538dfdae8
(usb: Provide usb_speed_string() function)
Signed-off-by: Alexander Aring <a.aring@phytec.de>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The "BCLR" in CFIFOCTR/DnFIFOCTR can flush the fifo of "CPU side" only.
To flush the fifo of "SIE side", we have to use the "ACLRM" in PIPEnCTR.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The udc-newstyle needs device_register in probe() of platform_device.
If it doesn't call, kernel panic happens in the sysfs_create_dir() when
we run modprobe a gadget driver.
[ balbi@ti.com : fix compile warning introduced by this patch ]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Those are simply giving information about the current
state of the UDC, nothing really fancy. We can let
everybody read those.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb_gadget_disconnect() is responsible of removing
data pullups. Before doing that we must, first, tell
gadget driver we're disconnecting (by calling disconnect
method on gadget driver structure), unbind the gadget
driver and stop the controller.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We should not be using dev_get_drvdata() because we
never call dev_set_drvdata(). Let's use container_of()
as all other sysfs attributes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is no Kconfig symbol named USB_GADGET_S3C_HSOTG_PIO. The select
statement for that symbol is a nop. Drop it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
With module.h being implicitly everywhere via device.h, the absence
of explicitly including something for EXPORT_SYMBOL went unnoticed.
Since we are heading to fix things up and clean module.h from the
device.h file, we need to explicitly include these files now.
Use the lightweight version of the header that has just THIS_MODULE
and EXPORT_SYMBOL variants.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The situation up to this point meant that module.h was pretty
much everywhere, regardless of whether you asked for it or not.
We are fixing that, so give the USB folks who want it an actual
include of it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (260 commits)
usb: renesas_usbhs: fixup inconsistent return from usbhs_pkt_push()
usb/isp1760: Allow to optionally trigger low-level chip reset via GPIOLIB.
USB: gadget: midi: memory leak in f_midi_bind_config()
USB: gadget: midi: fix range check in f_midi_out_open()
QE/FHCI: fixed the CONTROL bug
usb: renesas_usbhs: tidyup for smatch warnings
USB: Fix USB Kconfig dependency problem on 85xx/QoirQ platforms
EHCI: workaround for MosChip controller bug
usb: gadget: file_storage: fix race on unloading
USB: ftdi_sio.c: Use ftdi async_icount structure for TIOCMIWAIT, as in other drivers
USB: ftdi_sio.c:Fill MSR fields of the ftdi async_icount structure
USB: ftdi_sio.c: Fill LSR fields of the ftdi async_icount structure
USB: ftdi_sio.c:Fill TX field of the ftdi async_icount structure
USB: ftdi_sio.c: Fill the RX field of the ftdi async_icount structure
USB: ftdi_sio.c: Basic icount infrastructure for ftdi_sio
usb/isp1760: Let OF bindings depend on general CONFIG_OF instead of PPC_OF .
USB: ftdi_sio: Support TI/Luminary Micro Stellaris BD-ICDI Board
USB: Fix runtime wakeup on OHCI
xHCI/USB: Make xHCI driver have a BOS descriptor.
usb: gadget: add new usb gadget for ACM and mass storage
...
There is a small memory leak on the error paths.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
! has higher precedence than >= and since neither 0 nor 1 are greater
than 8 the condition is always false.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a race, reproduced rarely if you unload the module
when host finishes mass storage device initialization (reading
partition table and so on): fsg_unbind() code first closes
lun files then waits for worker thread to finish its work, as
the result the thread may operate on already closed device
with an oops and backtrace:
[ 484.937225] [<b00e403c>] (touch_atime+0x4/0x140) from [<b00a1498>] (generic_file_aio_read+0x678/0x6f0)
[ 484.946563] [<b00a1498>] (generic_file_aio_read+0x678/0x6f0) from [<b00d08c4>] (do_sync_read+0xb0/0xf4)
[ 484.955963] [<b00d08c4>] (do_sync_read+0xb0/0xf4) from [<b00d1478>] (vfs_read+0xac/0x144)
[ 484.964172] [<b00d1478>] (vfs_read+0xac/0x144) from [<af24c6a8>] (fsg_setup+0x7f4/0x900 [g_file_storage])
[ 484.973785] [<af24c6a8>] (fsg_setup+0x7f4/0x900 [g_file_storage]) from [<af24da14>] (fsg_main_thread+0x85c/0x175c [g_file_storage])
[ 484.985626] [<af24da14>] (fsg_main_thread+0x85c/0x175c [g_file_storage]) from [<b0077c48>] (kthread+0x7c/0x84)
[ 484.995666] [<b0077c48>] (kthread+0x7c/0x84) from [<b002f950>] (kernel_thread_exit+0x0/0x8)
[ 485.004028] Code: eaffffd0 e28dd008 e8bd8df0 e92d40f7 (e591400c)
Change the order in unbind: wait for the thread first, then close
the files.
Signed-off-by: Yauheni Kaliuta <yauheni.kaliuta@nokia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver provides two functions in one configuration:
a mass storage, and a ACM (serial port) link.
Heavily based on multi.c and cdc2.c
Signed-off-by: Klaus Schwarzkopf <schwarzkopf@sensortherm.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
| drivers/usb/gadget/mv_udc_core.c: In function 'handle_setup_packet':
| drivers/usb/gadget/mv_udc_core.c:1556:6: warning: 'status' may be \
used uninitialized in this function
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch is going to support clock gating when vbus detection is
posible. Clock and phy will be on only when usb gadget is used(vbus valid).
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
use DMA API for status_req's dma address, it is needed by dtd.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The controller will prime failure sometimes when do the iperf test.
Add delay to wait controller release dtd dma before we free it.
Then the issue is gone.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch is going to correct the ep0 state, and the unexpected
ep0 package warning can be removed.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
1: Add parameter check.
2: For controller endpoint, we need to flush in and out directions.
3: delete redundant code, make it more readable.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to the comment right above the code, we should use
USB_ENDPOINT_XFER_BULK instead.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The ep enable / disable functions can be called from interrupt
context, and they are not race safe on SMP systems. The critical
data can be modified in more than one routing.
Make them race safe by using IRQ-safe spinlock functions.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For the code doesn't restrict controller ep must be ep0, so we will go
through all the eps and check if there is a setup package received.
And also we just need to acknowledge the corresponding bit in
ENDPTSETUPSTAT register.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Set next dtd ptr to EP_QUEUE_HEAD_NEXT_TERMINATE for dqh when init ep0.
It means the dQH is empty.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to ChipIdea datasheet, there is no toggle flag for ep0.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The max size of data payload is in bit0 - bit10, so we need use 0x7ff
as the bitmask to fetch from usb_endpoint_descriptor.wMaxPacketSize.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some platforms will use usb to download images, the controller may not
be stopped correctly when start kernel. In some cases, it may have some
pending interrupts, and they will be triggered immediately when we finish
requesting irq in function probe. But we haven't finished the device
initialization at this time. So let's stop udc here to avoid this case
occurred.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Tag the probe function as __devinit.
Tag the remove function as __devexit.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch do the following things:
1. Add header and Copyright for marvell usb driver.
2. Add mv_usb.h in include/linux/platform_data, make the driver
fits all the marvell platform using the same ChipIdea usb ip.
3. Some SOC may has mutiple clock sources, so let me define it
in mv_usb_platform_data and give two helper functions named
udc_clock_enable/udc_clock_disable to deal with the clocks.
4. Different SOCs will have some difference in PHY initialization,
so we will remove file mv_udc_phy.c and add two funtions in
mv_usb_platform_data, let the platform relative driver to realize it.
5. Rewrite probe function according to the modification list above. Find
it will kernel panic when probe failed. The root cause is as follows:
When probe failed, the error handle may call device_unregister()
which in return will call gadget_release.In current code,
gadget_release have two issues:
1: the_controller is a NULL pointer.
2: if we free udc here, then the following code in probe
will access NULL pointer.
Signed-off-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch adds superspeed descriptors for the
storage gadgets.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
While being there, change C++ style comments to /* */.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
A recent commit obsoleted the is_vbus_present function, so
we must not use it any more.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The Synopsys USB device controller requires all OUT transfer request
lengths to be aligned to max packet size. The mass storage gadgets do
not meet this requirement for Super Speed. The gadgets already have a
function which performs this alignment for CBW packets, so use it for
data packets too.
The alternative would be to implement bounce buffers in the DWC3
driver, but that could have a significant impact on performance.
This version is based upon a more-correct patch written by Alan
Stern.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The code in the MIDI gadget was already sort of prepared for multi-port
configuration, so the streaming logic itself didn't need much tweaking.
However, the descriptors change when the number of ports do, and so some
rework of the the preparation algorithms were necessary.
Successfully tested on Linux and Max OS X hosts for both input and
output streams.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make use of the newly added MIDI function in f_midi.c and strip down
the MIDI gadget code radically. Also use the generic framework function
to avoid code duplication and rename some symbols to bring them in sync
with other code in the gadget framework.
[ balbi@ti.com : fix Section mismatch warnings.
rebased on top of usb_speed_string() patch to
avoid conflicts. ]
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds f_midi.c to implement a USB gadget function that works
with the composite framework, so it can be combined with other USB
functions.
The code for the ALSA/MIDI logic was taken from the midi device gadget,
other parts have been rewritten to benefit from the dynamic descriptor
allocation features.
This was successfully tested on an OMAP3 board.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move function to fix langwell_udc.c build error:
drivers/usb/gadget/langwell_udc.c: In function 'show_langwell_udc':
drivers/usb/gadget/langwell_udc.c:1693:3: error: implicit declaration of function 'lpm_device_speed'
drivers/usb/gadget/langwell_udc.c: At top level:
drivers/usb/gadget/langwell_udc.c:2637:37: error: conflicting types for 'lpm_device_speed'
drivers/usb/gadget/langwell_udc.c:1693:20: note: previous implicit declaration of 'lpm_device_speed' was here
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: linux-usb@vger.kernel.org
SH7757 has a USB function with internal DMA controller (SUDMAC).
This patch supports the SUDMAC. The SUDMAC is incompatible with
general-purpose DMAC. So, it doesn't use dmaengine.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch also fix the balance of braces.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
R8A66597 has the pin of WR0 and WR1. So, if one write-pin of CPU
connects to the pins, we have to change the setting of FIFOSEL
register in the controller. If we don't change the setting,
the controller cannot send the data of odd length.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We should not be using dev_get_drvdata() because we
never call dev_set_drvdata(). Let's use container_of()
as all other sysfs attributes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The allocated chardevice region range is only 1 device but on
unregister it currently tries to deregister 2.
Found this while doing a insmod/rmmod/insmod/rm... of the module
which seemed to eat major numbers.
Signed-off-by: Fabian Godehardt <fg@emlix.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a transceiver is available use otg_set_power to submit
the target current to it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In a few places in the kernel, the code prints
a human-readable USB device speed (eg. "high speed").
This involves a switch statement sometimes wrapped
around in ({ ... }) block leading to code repetition.
To mitigate this issue, this commit introduces
usb_speed_string() function, which returns
a human-readable name of provided speed.
It also changes a few places switch was used to use
this new function. This changes a bit the way the
speed is printed in few instances at the same time
standardising it.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It was pointed out by 'make versioncheck' that linux/version.h was not
always being included where needed and sometimes included needlessly
in drivers/usb/.
This patch fixes up the includes.
For the UVC gadget driver bits, this was ACK'ed by Laurent Pinchart.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is a resend from the original, changing the title from PATCH to
RFC(since this is a review for commit, and I should have put that the first go around).
and also removing some of the commit's with ia64 and bash since it is significant.
let me know if I might have missed anything etc..
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
remove the following two paragraphs as they are not needed:
This program is distributed in the hope that it will be useful, but
WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
License for more details.
You should have received a copy of the GNU General Public License along with
this program; if not, write to the Free Software Foundation, Inc.,59
Temple Place - Suite 330, Boston, MA 02111-1307, USA.
Signed-off-by: Klaus Schwarzkopf <schwarzkopf@sensortherm.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On Audio class, the wLength field of the Setup
packet, contains the data payload size of the
following Data phase. Instead of harcoding values,
use wLength.
This also fixes a bug where Gadget driver had to
receive 3 bytes, but it was queueing a ZLP.
Signed-off-by: Felipe Balbi <balbi@ti.com>
While testing g_audio with HighSpeed UDC on a
FS Hub, we had no configurations to present to
the host. That's because both speeds where
mutually exclusive.
Signed-off-by: Felipe Balbi <balbi@ti.com>
FSG_NUM_BUFFERS is set to 2 as default.
Usually 2 buffers are enough to establish a good buffering pipeline.
The number may be increased in order to compensate a for bursty VFS
behaviour.
Here follows a description of system that may require more than
2 buffers.
* CPU ondemand governor active
* latency cost for wake up and/or frequency change
* DMA for IO
Use case description.
* Data transfer from MMC via VFS to USB.
* DMA shuffles data from MMC and to USB.
* The CPU wakes up every now and then to pass data in and out from VFS,
which cause the bursty VFS behaviour.
Test set up
* Running dd on the host reading from the mass storage device
* cmdline: dd if=/dev/sdb of=/dev/null bs=4k count=$((256*100))
* Caches are dropped on the host and on the device before each run
Measurements on a Snowball board with ondemand_governor active.
FSG_NUM_BUFFERS 2
104857600 bytes (105 MB) copied, 5.62173 s, 18.7 MB/s
104857600 bytes (105 MB) copied, 5.61811 s, 18.7 MB/s
104857600 bytes (105 MB) copied, 5.57817 s, 18.8 MB/s
FSG_NUM_BUFFERS 4
104857600 bytes (105 MB) copied, 5.26839 s, 19.9 MB/s
104857600 bytes (105 MB) copied, 5.2691 s, 19.9 MB/s
104857600 bytes (105 MB) copied, 5.2711 s, 19.9 MB/s
There may not be one optimal number for all boards. This is why
the number is added to Kconfig. If selecting USB_GADGET_DEBUG_FILES
this value may be set by a module parameter as well.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch (as1481) fixes a problem affecting g_file_storage and
g_mass_storage when running at SuperSpeed. The two drivers currently
assume that the bulk-out maxpacket size can evenly divide the SCSI
block size, which is 512 bytes. But SuperSpeed bulk endpoints have a
maxpacket size of 1024, so the assumption is no longer true.
This patch removes that assumption from the drivers, by getting rid of
a small optimization (they try to align VFS reads and writes on page
cache boundaries). If a command's starting logical block address is
512 bytes below the end of a page, it's not okay to issue a USB
command for just those 512 bytes when the maxpacket size is 1024 -- it
would result in either babble (for an OUT transfer) or a short packet
(for an IN transfer).
Also, for backward compatibility, the test for writes extending beyond
the end of the backing storage has to be changed. If the host tries
to do this, we should accept the data that fits in the backing storage
and ignore the rest. Because the storage's end may not align with a
USB packet boundary, this means we may have to accept a USB OUT
transfer that extends beyond the end of the storage and then write out
only the part of the data that fits.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now the mass storage driver has fixed logic block size of 512 bytes.
The mass storage gadget read/write bound devices only through VFS, so the
bottom level devices actually are just RAW devices to the driver and connected
PC. As a RAW, hosts can always format, read and write it right in 512 bytes
logic block and don't care about the actual logic block size of devices bound
to the gadget.
But if we want to share the bound block device partition between target board
and PC, in case the logic block size of the bound block device is 4KB, we
execute the following steps:
1. connect a board with mass storage gadget to PC(the board has set one
partition of on-board block device as file name of the mass storage)
2. PC format the mass storage to VFAT by default logic block size and
read/write it
3. disconnect boards from PC
4. target board mount the partition as VFAT
Step 4 will fail since kernel on target thinks the logic block size of the
bound partition as 4KB.
A typical error is "FAT: logical sector size too small for device (logical
sector size = 512)"
If we execute opposite steps:
1. format the partition to VFAT on target board and read/write this partition
2. connect the board to Windows PC as usb mass storage gadget, windows will
think the disk is not formatted
So the conclusion is that only as a gadget, the mass storage driver has no any
problem. But being shared VFAT or other filesystem on PC and target board, it
will fail.
This patch adapts logic block size to bound block devices and fix the issue.
Cc: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peiyu Li <peiyu.li@csr.com>
Signed-off-by: Xianglong Du <xianglong.du@csr.com>
Signed-off-by: Huayi Li <huayi.li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The ARCH_MX1 scheduled for removal. Instead, depend on ARCH_MXC
and make clear in the Kconfig text that only i.MX1 has this
hardware.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now ${LINUX}/drivers/usb/* can use usb_endpoint_maxp(desc) to get maximum packet size
instead of le16_to_cpu(desc->wMaxPacketSize).
This patch fix it up
Cc: Armin Fuerst <fuerst@in.tum.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Johannes Erdfelt <johannes@erdfelt.com>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: David Kubicek <dave@awk.cz>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Brad Hards <bhards@bigpond.net.au>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Thomas Dahlmann <dahlmann.thomas@arcor.de>
Cc: David Brownell <david-b@pacbell.net>
Cc: David Lopo <dlopo@chipidea.mips.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Xie Xiaobo <X.Xie@freescale.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Jiang Bo <tanya.jiang@freescale.com>
Cc: Yuan-hsin Chen <yhchen@faraday-tech.com>
Cc: Darius Augulis <augulis.darius@gmail.com>
Cc: Xiaochen Shen <xiaochen.shen@intel.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: OKI SEMICONDUCTOR, <toshiharu-linux@dsn.okisemi.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Herbert Pötzl <herbert@13thfloor.at>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Roman Weissgaerber <weissg@vienna.at>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: Florian Floe Echtler <echtler@fs.tum.de>
Cc: Christian Lucht <lucht@codemercs.com>
Cc: Juergen Stuber <starblue@sourceforge.net>
Cc: Georges Toth <g.toth@e-biz.lu>
Cc: Bill Ryder <bryder@sgi.com>
Cc: Kuba Ober <kuba@mareimbrium.org>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Makes it possible to use i.e. gpio-vbus to handle vbus events.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usb-interrupt is requested before the endpoints are initalised.
If an interrupt happens in the time between request_irq and the init
of the endpoint-data (as seen on the Qisda ESx00 ebook-platforms),
it is therefore possible for the interrupt handler to access endpoint-
data before its creation resulting in a null-pointer dereference.
This patch simply moves the irq request below the endpoint init.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The DesignWare USB3 is a highly
configurable IP Core which can be
instantiated as Dual-Role Device (DRD),
Peripheral Only and Host Only (XHCI)
configurations.
Several other parameters can be configured
like amount of FIFO space, amount of TX and
RX endpoints, amount of Host Interrupters,
etc.
The current driver has been validated with
a virtual model of version 1.73a of that core
and with an FPGA burned with version 1.83a
of the DRD core. We have support for PCIe
bus, which is used on FPGA prototyping, and
for the OMAP5, more adaptation (or glue)
layers can be easily added and the driver
is half prepared to handle any possible
configuration the HW engineer has chosen
considering we have the information on
one of the GHWPARAMS registers to do
runtime checking of certain features.
More runtime checks can, and should, be added
in order to make this driver even more flexible
with regards to number of endpoints, FIFO sizes,
transfer types, etc.
While this supports only the device side, for
now, we will add support for Host side (xHCI -
see the updated series Sebastian has sent [1])
and OTG after we have it all stabilized.
[1] http://marc.info/?l=linux-usb&m=131341992020339&w=2
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch to fix an issue with the HID gadget which, at the moment,
returns STALL on a HID descriptor request. Essentially, the patch changes
the hid gadget such that a request for the HID descriptor is handled by
copying the descriptor into the response buffer, rather than falling
through the default case, in which the request is answered by a STALL.
Signed-off-by: Sebastian Bauer <mail@sebastianbauer.info>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After 622859634 (usb: musb: drop a gigantic amount of ifdeferry):
- USB_GADGET_MUSB_HDRC is no longer selectable because it
depends on the removed USB_MUSB_PERIPHERAL and USB_MUSB_OTG
options
- The Kconfig comment still says "Enable Host or Gadget support
to see Inventra options", even though you now need to enable
both of them to see Inventra options.
Fix the dependency and drop the anyway unnecessary comment.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For bMaxPacketSize0 we usually take what is specified in ep0->maxpacket.
This is fine in most cases, however on SuperSpeed bMaxPacketSize0
specifies the exponent instead of the actual size in bytes. The only
valid value on SS is 9 which denotes 512 bytes.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The code in this block is unused and the Author is fine with removing:
| These functions were used to debug unstable hw fifo while developing
| fusb300. It's much more stable now.
| So these functions can be removed.
Cc: "Wendy Yuan-Hsin Chen" <yhchen@faraday-tech.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
platform_device_id structures need a NULL terminating
entry, add it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
<linux/irq.h> states:
* Please do not include this file in generic code. There is currently
* no requirement for any architecture to implement anything held
* within this file.
prefetch() and prefetchw() need <linux/prefetch.h> on m68k:
drivers/usb/gadget/net2272.c: In function ‘net2272_write_fifo’:
drivers/usb/gadget/net2272.c:468: error: implicit declaration of function ‘prefetch’
drivers/usb/gadget/net2272.c: In function ‘net2272_read_fifo’:
drivers/usb/gadget/net2272.c:574: error: implicit declaration of function ‘prefetchw’
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch to fix an issue with the HID gadget which, at the moment,
returns STALL on a HID descriptor request. Essentially, the patch changes
the hid gadget such that a request for the HID descriptor is handled by
copying the descriptor into the response buffer, rather than falling
through the default case, in which the request is answered by a STALL.
Signed-off-by: Sebastian Bauer <mail@sebastianbauer.info>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After 622859634 (usb: musb: drop a gigantic amount of ifdeferry):
- USB_GADGET_MUSB_HDRC is no longer selectable because it
depends on the removed USB_MUSB_PERIPHERAL and USB_MUSB_OTG
options
- The Kconfig comment still says "Enable Host or Gadget support
to see Inventra options", even though you now need to enable
both of them to see Inventra options.
Fix the dependency and drop the anyway unnecessary comment.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For bMaxPacketSize0 we usually take what is specified in ep0->maxpacket.
This is fine in most cases, however on SuperSpeed bMaxPacketSize0
specifies the exponent instead of the actual size in bytes. The only
valid value on SS is 9 which denotes 512 bytes.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The code in this block is unused and the Author is fine with removing:
| These functions were used to debug unstable hw fifo while developing
| fusb300. It's much more stable now.
| So these functions can be removed.
Cc: "Wendy Yuan-Hsin Chen" <yhchen@faraday-tech.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
platform_device_id structures need a NULL terminating
entry, add it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (430 commits)
[media] ir-mce_kbd-decoder: include module.h for its facilities
[media] ov5642: include module.h for its facilities
[media] em28xx: Fix DVB-C maxsize for em2884
[media] tda18271c2dd: Fix saw filter configuration for DVB-C @6MHz
[media] v4l: mt9v032: Fix Bayer pattern
[media] V4L: mt9m111: rewrite set_pixfmt
[media] V4L: mt9m111: fix missing return value check mt9m111_reg_clear
[media] V4L: initial driver for ov5642 CMOS sensor
[media] V4L: sh_mobile_ceu_camera: fix Oops when USERPTR mapping fails
[media] V4L: soc-camera: remove soc-camera bus and devices on it
[media] V4L: soc-camera: un-export the soc-camera bus
[media] V4L: sh_mobile_csi2: switch away from using the soc-camera bus notifier
[media] V4L: add media bus configuration subdev operations
[media] V4L: soc-camera: group struct field initialisations together
[media] V4L: soc-camera: remove now unused soc-camera specific PM hooks
[media] V4L: pxa-camera: switch to using standard PM hooks
[media] NetUP Dual DVB-T/C CI RF: force card hardware revision by module param
[media] Don't OOPS if videobuf_dvb_get_frontend return NULL
[media] NetUP Dual DVB-T/C CI RF: load firmware according card revision
[media] omap3isp: Support configurable HS/VS polarities
...
Fix up conflicts:
- arch/arm/mach-omap2/board-rx51-peripherals.c:
cleanup regulator supply definitions in mach-omap2
vs
OMAP3: RX-51: define vdds_csib regulator supply
- drivers/staging/tm6000/tm6000-alsa.c (trivial)
The driver had to decide how many events to allocate when the v4l2_fh struct
was created. It was possible to add more events afterwards, but there was no
way to ensure that you wouldn't miss important events if the event queue
would fill up for that filehandle.
In addition, once there were no more free events, any new events were simply
dropped on the floor.
For the control event in particular this made life very difficult since
control status/value changes could just be missed if the number of allocated
events and the speed at which the application read events was too low to keep
up with the number of generated events. The application would have no idea
what the latest state was for a control since it could have missed the latest
control change.
So this patch makes some major changes in how events are allocated. Instead
of allocating events per-filehandle they are now allocated when subscribing an
event. So for that particular event type N events (determined by the driver)
are allocated. Those events are reserved for that particular event type.
This ensures that you will not miss events for a particular type altogether.
In addition, if there are N events in use and a new event is raised, then
the oldest event is dropped and the new one is added. So the latest event
is always available.
This can be further improved by adding the ability to merge the state of
two events together, ensuring that no data is lost at all. This will be
added in the next patch.
This also makes it possible to allow the user to determine the number of
events that will be allocated. This is not implemented at the moment, but
would be trivial.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers that supported events used to be rare, but now that controls can also
raise events this will become much more common since almost all drivers have
controls.
This means that keeping struct v4l2_events as a separate struct make no more
sense. Merging it into struct v4l2_fh simplifies things substantially as it
is now an integral part of the filehandle struct.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (115 commits)
EHCI: fix direction handling for interrupt data toggles
USB: serial: add IDs for WinChipHead USB->RS232 adapter
USB: OHCI: fix another regression for NVIDIA controllers
usb: gadget: m66592-udc: add pullup function
usb: gadget: m66592-udc: add function for external controller
usb: gadget: r8a66597-udc: add pullup function
usb: renesas_usbhs: support multi driver
usb: renesas_usbhs: inaccessible pipe is not an error
usb: renesas_usbhs: care buff alignment when dma handler
USB: PL2303: correctly handle baudrates above 115200
usb: r8a66597-hcd: fixup USB_PORT_STAT_C_SUSPEND shift
usb: renesas_usbhs: compile/config are rescued
usb: renesas_usbhs: fixup comment-out
usb: update email address in ohci-sh and r8a66597-hcd
usb: r8a66597-hcd: add function for external controller
EHCI: only power off port if over-current is active
USB: mon: Allow to use usbmon without debugfs
USB: EHCI: go back to using the system clock for QH unlinks
ehci: add pci quirk for Ordissimo and RM Slate 100 too
ehci: refactor pci quirk to use standard dmi_check_system method
...
Fix up trivial conflicts in Documentation/feature-removal-schedule.txt
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (107 commits)
vfs: use ERR_CAST for err-ptr tossing in lookup_instantiate_filp
isofs: Remove global fs lock
jffs2: fix IN_DELETE_SELF on overwriting rename() killing a directory
fix IN_DELETE_SELF on overwriting rename() on ramfs et.al.
mm/truncate.c: fix build for CONFIG_BLOCK not enabled
fs:update the NOTE of the file_operations structure
Remove dead code in dget_parent()
AFS: Fix silly characters in a comment
switch d_add_ci() to d_splice_alias() in "found negative" case as well
simplify gfs2_lookup()
jfs_lookup(): don't bother with . or ..
get rid of useless dget_parent() in btrfs rename() and link()
get rid of useless dget_parent() in fs/btrfs/ioctl.c
fs: push i_mutex and filemap_write_and_wait down into ->fsync() handlers
drivers: fix up various ->llseek() implementations
fs: handle SEEK_HOLE/SEEK_DATA properly in all fs's that define their own llseek
Ext4: handle SEEK_HOLE/SEEK_DATA generically
Btrfs: implement our own ->llseek
fs: add SEEK_HOLE and SEEK_DATA flags
reiserfs: make reiserfs default to barrier=flush
...
Fix up trivial conflicts in fs/xfs/linux-2.6/xfs_super.c due to the new
shrinker callout for the inode cache, that clashed with the xfs code to
start the periodic workers later.
Btrfs needs to be able to control how filemap_write_and_wait_range() is called
in fsync to make it less of a painful operation, so push down taking i_mutex and
the calling of filemap_write_and_wait() down into the ->fsync() handlers. Some
file systems can drop taking the i_mutex altogether it seems, like ext3 and
ocfs2. For correctness sake I just pushed everything down in all cases to make
sure that we keep the current behavior the same for everybody, and then each
individual fs maintainer can make up their mind about what to do from there.
Thanks,
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
M66592 has the pin of WR0 and WR1. So, if one write-pin of CPU
connects to the pins, we have to change the setting of FIFOSEL
register in the controller. If we don't change the setting,
the controller cannot send the data of odd length.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch rescues renesas_usbhs compile from
commit 193ab2a (usb: gadget: allow multiple gadgets to be built)
CONFIG_USB_RENESAS_USBHS compile renesas_usbhs main code which
is shared between Host/Gadget.
CONFIG_USB_RENESAS_USBHS_UDC add mod_gadget to it.
It had lost USB_GADGET_DUALSPEED
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds SuperSpeed descriptors to the
g_zero gadget.
The SuperSpeed descriptors were added both for
f_soursesink and f_loopback function drivers.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Amit Blay <ablay@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add SuperSpeed descriptors to the Network USB
function drivers.
This has been lightly tested using a Linux host.
I was able to ssh from device to host and host to
device, no obvious problems seen.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The USB high speed device must support the TEST_MODE, but the driver
didn't support it. When we sent the SET_FEATURE for TEST_MODE to
the driver, the request was successful, but the module didn't enter
the TEST_MODE.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The USB high speed device must support the TEST_MODE, but the driver
didn't support it. When we sent the SET_FEATURE for TEST_MODE to
the driver, the request was successful, but the module didn't enter
the TEST_MODE.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
BUSWAIT is a 4-bit-wide value that controls the number of access waits
from the CPU to on-chip USB module. b'0000 inserts 0 wait (2 access
cycles) and b'1111 inserts 15 waits (17 access cycles, hardware
initial value), respectively.
BUSWAIT value depends on peripheral clock frequency supplied to on-chip
of each CPU, hence should be configurable through platform data.
Note that this patch assumes that b'0000 (0 wait, 2 access cycles) is
rerely used and considered as invalid. If valid 'buswait' data is not
provided by platform, initial b'1111 (15 waits, 17 access cycles) will
be applied as a safe default.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When we run rmmod a gadget driver, the driver will call
disable_controller(). Then, because the bit of USBE in SYSCFG0 was
cleared in on_chip=1 mode, we could not connect the usb when we run
insmod a gadget driver next time.
This patch also cleans up probe() and ->stop() about unnecessary
init_controller().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Both fusb300 and langwell udcs seem to only
work with 32-bit address space.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
- remove pointer u32 abuse in fusb300_fill_idma_prdtbl().
It is assigned the dma_addr to a pointer and then back.
Poor families may have to recycle variables but we don't
- don't free req.buf in error case. We don't do it in the
ok case so it is probably wrong to do it in error case.
- return in error case. There is no reason to continue
without data and performing ops on an invalid pointer.
- The if (d) statement is bogus since an invalid DMA pointer
is ~0 on some architecutres. And since we return for the
invalid case we don't need it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix the following compile warning:
| usb/gadget/ci13xxx_udc.c: In function 'show_registers':
| usb/gadget/ci13xxx_udc.c:1242:1: warning: the frame size of 2064 bytes is larger than 1024 bytes
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the following compile warnings:
drivers/usb/gadget/net2272.c: In function ‘net2272_kick_dma’:
drivers/usb/gadget/net2272.c:740:2: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 6 has type ‘dma_addr_t’ [-Wformat]
drivers/usb/gadget/net2272.c: In function ‘net2272_queue’:
drivers/usb/gadget/net2272.c:859:2: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 8 has type ‘dma_addr_t’ [-Wformat]
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the following compile warnings:
drivers/usb/gadget/langwell_udc.c: In function ‘queue_dtd’:
drivers/usb/gadget/langwell_udc.c:596:2: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/usb/gadget/langwell_udc.c: In function ‘langwell_udc_probe’:
drivers/usb/gadget/langwell_udc.c:3274:2: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ [-Wformat]
drivers/usb/gadget/langwell_udc.c:3289:2: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ [-Wformat]
drivers/usb/gadget/langwell_udc.c: In function ‘langwell_udc_resume’:
drivers/usb/gadget/langwell_udc.c:3473:2: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ [-Wformat]
drivers/usb/gadget/langwell_udc.c:3487:2: warning: format ‘%d’ expects argument of type ‘int’, but argument 4 has type ‘size_t’ [-Wformat]
Signed-off-by: Felipe Balbi <balbi@ti.com>
that code has been dead forever. Since the
first commit (0fe6f1d1) the use of that code
has been commented out. Let's drop the dead
code already and fix the following compile
warning:
| drivers/usb/gadget/fusb300_udc.c: At top level:
| drivers/usb/gadget/fusb300_udc.c:771:13: warning: ‘fusb300_wrfifo’ defined but not used [-Wunused-function]
| drivers/usb/gadget/fusb300_udc.c:1027:13: warning: ‘fusb300_set_ep_bycnt’ defined but not used [-Wunused-function]
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a bug in Samsung's UDC driver, which is completely disabling
the USB device when a custom UDC command is used.
Following patch seems to get the right behavior (e.g. enabling pull-up
instead of disabling then Vcc is applied).
Signed-off-by: Viliam Mateicka <viliam.mateicka@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A compilation warning was added by the patch
"usb: gadget: use config_ep_by_speed() instead of ep_choose()".
This patch fixed it.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The recent commit 2edb11cbac fixed req->length in the composite_setup()
function, but that will cause all g_zero tests to fail like:
root#> ./testusb -D /proc/bus/usb/002/021 -t14 -c 15000 -s 256 -v 1
unknown speed /proc/bus/usb/002/021
/proc/bus/usb/002/021 test 14 --> 32 (Broken pipe)
We need to fix req->length in sourcesink_setup() as well to avoid this.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This was somehow forgotten.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
bind() and pull is moved to udc core, call callbacks are verified by the
upper layer.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
udc_start() should only trigger the internal state machine and make
minimal house keeping. Before that call udc-core calls the bind()
callback and after the callback the pullup().
udc_stop() is simillar, udc-core calls pullup(), unbind() and finally
udc_stop().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The configuration is static however we only know the speed after we have
connected with the other side.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This value is now assigned during bind(). The configuration depends on
static values assigned by dummy driver itself. So there is no need to
defer this assigment until one know the actuall speed since the
configuration is static and known early.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is only required to be done once. There is no counter part to this
in ->stop() so there is no need to re-do it next time. While here also
init the max_stream size to 0 on SS speed.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
maxpacket is set by the udc driver for ep0 very early. This value is
copied by the function gadget used later for the USB_DT_DEVICE and
USB_DT_DEVICE_QUALIFIER query. This seems to work fine so far. For USB3
we need set a different value here. In SS speed it is 2^x with x=9 and
in HS we set something <= 64. If the UDC starts in SS and continues in
HS after the cable has been plugged it will report a too small value.
There setting of this value is defered and taken automaticly from the
ep0 pointer where the UDC driver can update it according to the speed it
detected _after_ a cable has been plugged.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
now that we have the udc class, we can allow
multiple gadget controller drivers to be
compiled as modules. This will allow for
distro-like kernels for embedded devices.
With this patch, I managed to build an x86
kernel with support for many of the controllers
enabled:
CONFIG_USB_FUSB300=m
CONFIG_USB_R8A66597=m
CONFIG_USB_M66592=m
CONFIG_USB_AMD5536UDC=m
CONFIG_USB_CI13XXX_PCI=m
CONFIG_USB_NET2272=m
CONFIG_USB_NET2280=m
CONFIG_USB_GOKU=m
CONFIG_USB_LANGWELL=m
CONFIG_USB_EG20T=m
Also an ARM kernel with support for many controllers:
CONFIG_USB_FUSB300=m
CONFIG_USB_OMAP=m
CONFIG_USB_R8A66597=m
CONFIG_USB_GADGET_MUSB_HDRC=m
CONFIG_USB_M66592=m
CONFIG_USB_NET2272=m
CONFIG_USB_DUMMY_HCD=m
The next step would be to get rid of the
direct access to arch/ and mach/ directories
on some gadget controllers so that we can
build all of them without depending on their
respective ARCH_* symbols.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This function has no user in my tree. It looks like it belongs to
net2280 but it somehow morphed into the dummy_hcd. So I remove it
before it spreads into more drivers.
After some digging I figured out that the only user was removed in
|commit 9079e91b5b
|Author: David Brownell <david-b@pacbell.net>
|Date: Wed May 7 16:00:36 2008 -0700
|
| USB: serial gadget: cleanup/reorg
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Taking the correct struct once avoids doing the speed dance.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
gadget_to_dummy_hcd() already does the speed check, so
it's unnecessary to unroll that all the time.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Before commit 53832daea ("usb: gadget: dummy_hcd: use the shared_hcd
infrastructure") the is_otg field was set in dummy_udc_probe(). It seems
to me that this field is used in gadget's bind function. Therefore I'm
moving it before the bind() callback is called.
Cc: Tatyana Brokhman <tlinder@codeaurora.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The removed code does the same thing as dummy_pullup(). The only
difference is that in dummy_udc_stop() the first dummy_pullup()
did not call usb_hcd_poll_rh_status().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the gadget controller number is only used
during bind() to update descriptors and/or
check that a particular controller can support
a particular gadget driver.
Because of that, we can remove the ifdef
trickery as it's a rather small optimization
anyway.
While at that, also sort the entries
alphabetically and add a comment stating we
want to keep the list ordered alphabetically.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 72c973d (usb: gadget: add usb_endpoint_descriptor
to struct usb_ep) has introduced a compile error to
ci13xxx_udc. Fix it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This also fixes the error path: If the second device fails to register
we never remove the first one.
This is compile-tested only. I don't see any difference between those
two. Maybe we should just use one name instead?
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Without it udev won't be able to load the driver once it notices the
device unbound.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In case pci_register_driver() fails it error will be 0 in case
platform_driver_register() was fine. Also without PCI
pci_register_driver() evaluates to 1 which is well, special. If
platform_driver_register() returns EINVAL or EBUSY we end up with 0.
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a new module parameter to dummy_hcd
called is_high_speed.
When set to false the connected device will be forced
to operate in full-speed mode. By default, this parameter
is set to 'true'.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds SS support to the dummy hcd module.
It may be used to test SS device when no (SS) HW is
available.
USB 3.0 hub includes 2 hubs - one HS and one SS. This
patch adds support for a SS root hub in the dummy_hcd
module.
A new module parameter was added: is_super_speed. When
set to true, a SS root hub will also be registered and
the connected device will be enumerated over the SS
root hub. The default of this parameter is false.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
[ balbi@ti.com : slight change to commit log
fixed one coding style issue ]
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is a preparation for adding SuperSpeed
support to dummy hcd.
It takes the master side fields out of the struct
dummy to a separate structure. The init process
was also modified to resemble the way it is
done by xHCI.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SuperSpeed USB has defined a new descriptor, called
the Binary Device Object Store (BOS) Descriptor. It
has also changed a bit the definition of SET_FEATURE
and GET_STATUS requests to add USB3-specific details.
This patch implements both changes to the Composite
Gadget Framework.
[ balbi@ti.com : slight changes to commit log
fixed a compile error on ARM ]
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This field is used by the Gadget drivers to specify
the maximum speed they support, meaning: the maximum
speed they can provide descriptors for.
The driver speed will be set in consideration of this
value.
[ balbi@ti.com : dropped the ifdeffery ]
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 09ba0def (USB: fsl_udc_core: prepare for SoCs with
BE registers and descriptors) introduced build breakage
on ARM arch. Fix it by setting accessors using a static
inline function which is a nop when compiling the driver
for ARM arch.
Commit 2ea6698 (USB: fsl_udc_core: support device mode of
MPC5121E DR USB Controller) caused another breakage on ARM
by using flush_dcache_range(). Don't use it, convert to the
DMA API usage instead. USB2.0CV Halt Endpoint Test succeeds
on PPC. Tested both on ARM i.MX31 and mpc5121 PPC, also with
CONFIG_DMA_API_DEBUG enabled.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch defines necessary fields to support
streaming for USB3.0.
It implements a new function, called
usb_ep_autoconfig_ss(), to be used instead of the
existing usb_ep_autoconfig() when working in
SuperSpeed mode and there is a need to search for
an endpoint according to the number of required
streams.
[ balbi@ti.com : slight changes to commit log ]
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fix the coding style of a few switches on the
gadget framework.
[ balbi@ti.com : add a commit log ]
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
