When the bonding module is loaded, it creates bond0 by default.
Then, when attempting to create bond0, the following messages
are printed to syslog:
kernel: bonding: bond0 is being created...
kernel: bonding: Bond creation failed.
Which seems to indicate a problem, when in reality there is no
problem. Since the actual error code is passed down from bond_create,
make use of it to print a bit less ominous message:
kernel: bonding: bond0 is being created...
kernel: bond0 already exists.
Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bringing up a bond interface with all network cables disconnected
does not properly set the interface as DOWN because the call to
netif_carrier_off occurs too early in bond_init. The call needs
to occur after register_netdevice has set dev->reg_state to
NETREG_REGISTERED, so that netif_carrier_off will trigger the
call to linkwatch_fire_event.
Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When packets come in from a device with >= 16 receive queues
headed out a bonding interface, syslog gets filled with this:
kernel: bond0 selects TX queue 16, but real number of TX queues is 16
because queue_mapping is offset by 1. Adjust return value
to account for the offset.
This is a revision of my earlier patch (which did not use the
skb_rx_queue_* helpers - thanks to Ben for the suggestion).
Andy submitted a similar patch which emits a pr_warning on
invalid queue selection, but I believe the log spew is
not useful. We can revisit that question in the future,
but in the interim I believe fixing the core problem is
worthwhile.
Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
ECN support incorrectly maps ECN BESTEFFORT packets to TC_PRIO_FILLER
(1) instead of TC_PRIO_BESTEFFORT (0)
This means ECN enabled flows are placed in pfifo_fast/prio low priority
band, giving ECN enabled flows [ECT(0) and CE codepoints] higher drop
probabilities.
This is rather unfortunate, given we would like ECN being more widely
used.
Ref : http://www.coverfire.com/archives/2011/03/13/pfifo_fast-and-ecn/
Signed-off-by: Dan Siemon <dan@coverfire.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Dave Täht <d@taht.net>
Cc: Jonathan Morton <chromatix99@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function should return 0 in case of error, 1 if OK
commit 452edd598f (xfrm: Return dst directly from xfrm_lookup())
got it wrong.
Reported-and-bisected-by: Michael Smith <msmith@cbnco.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Status of UDP packet detection not getting populated in RX completion
structure. This is required in csum_passed() routine.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the pipe uses aligned-mode data packets, we must reserve 4 bytes
instead of 3 for the pipe protocol header. Otherwise the Phonet header
would not be aligned, resulting in potentially corrupted headers with
later unaligned memory writes.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Enable setting speed and auto negotiation parameters for GbE ports.
o Hardware do not support half duplex setting currently.
David Miller:
Amit please update your patch to silently reject link setting
attempts that are unsupported by the device.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes build error when SMSC_TRACE() used.
Signed-off-by: Jeongtae Park <jtp.park@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel will refuse certain types that do not work in ipv6 mode.
We can then add these features incrementally without risk of userspace
breakage.
Signed-off-by: Florian Westphal <fwestphal@astaro.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Followup patch will add ipv6 support.
ipt_addrtype.h is retained for compatibility reasons, but no longer used
by the kernel.
Signed-off-by: Florian Westphal <fwestphal@astaro.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Structures ip6t_replace, compat_ip6t_replace, and xt_get_revision are
copied from userspace. Fields of these structs that are
zero-terminated strings are not checked. When they are used as argument
to a format string containing "%s" in request_module(), some sensitive
information is leaked to userspace via argument of spawned modprobe
process.
The first bug was introduced before the git epoch; the second was
introduced in 3bc3fe5e (v2.6.25-rc1); the third is introduced by
6b7d31fc (v2.6.15-rc1). To trigger the bug one should have
CAP_NET_ADMIN.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Structures ipt_replace, compat_ipt_replace, and xt_get_revision are
copied from userspace. Fields of these structs that are
zero-terminated strings are not checked. When they are used as argument
to a format string containing "%s" in request_module(), some sensitive
information is leaked to userspace via argument of spawned modprobe
process.
The first and the third bugs were introduced before the git epoch; the
second was introduced in 2722971c (v2.6.17-rc1). To trigger the bug
one should have CAP_NET_ADMIN.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Structures ipt_replace, compat_ipt_replace, and xt_get_revision are
copied from userspace. Fields of these structs that are
zero-terminated strings are not checked. When they are used as argument
to a format string containing "%s" in request_module(), some sensitive
information is leaked to userspace via argument of spawned modprobe
process.
The first bug was introduced before the git epoch; the second is
introduced by 6b7d31fc (v2.6.15-rc1); the third is introduced by
6b7d31fc (v2.6.15-rc1). To trigger the bug one should have
CAP_NET_ADMIN.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
A potential race condition when generating connlimit_rnd is also fixed.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
We use the reply tuples when limiting the connections by the destination
addresses, however, in SNAT scenario, the final reply tuples won't be
ready until SNAT is done in POSTROUING or INPUT chain, and the following
nf_conntrack_find_get() in count_tem() will get nothing, so connlimit
can't work as expected.
In this patch, the original tuples are always used, and an additional
member addr is appended to save the address in either end.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This feature adds messaging to the link status change to notify
the user if the device returned from a downshift or power off
event due to the Thermal Sensor feature in i350 parts. Feature
is only available on internal copper ports.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hardware timestamping for Intel 82580 didn't work in either 2.6.36 or
2.6.37. Comparing it to Intel's igb-2.4.12 I found that the
timecounter_init clock/counter initialization was done too early.
Signed-off-by: Anders Berggren <andfers@halon.se>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
commit e9a799ea4a (xen: netfront: ethtool stats fields should be
unsigned long) made rx_gso_checksum_fixup an unsigned long.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Break out the portions of __ip_vs_control_init() and
__ip_vs_control_cleanup() where aren't necessary when
CONFIG_SYSCTL is undefined.
Signed-off-by: Simon Horman <horms@verge.net.au>
ip_vs_lblc_table and ip_vs_lblcr_table, and code that uses them
are unnecessary when CONFIG_SYSCTL is undefined.
Signed-off-by: Simon Horman <horms@verge.net.au>
Much of ip_vs_leave() is unnecessary if CONFIG_SYSCTL is undefined.
I tried an approach of breaking the now #ifdef'ed portions out
into a separate function. However this appeared to grow the
compiled code on x86_64 by about 200 bytes in the case where
CONFIG_SYSCTL is defined. So I have gone with the simpler though
less elegant #ifdef'ed solution for now.
Signed-off-by: Simon Horman <horms@verge.net.au>
ip_vs_conntrack_enabled() becomes a noop when CONFIG_SYSCTL is undefined.
In preparation for not including sysctl_conntrack in
struct netns_ipvs when CONFIG_SYCTL is not defined.
Signed-off-by: Simon Horman <horms@verge.net.au>
In preparation for not including sysctl_lblc{r}_expiration in
struct netns_ipvs when CONFIG_SYCTL is not defined.
Signed-off-by: Simon Horman <horms@verge.net.au>
In preparation for not including sysctl_expire_quiescent_template in
struct netns_ipvs when CONFIG_SYCTL is not defined.
Signed-off-by: Simon Horman <horms@verge.net.au>
In preparation for not including sysctl_expire_nodest_conn in
struct netns_ipvs when CONFIG_SYCTL is not defined.
Signed-off-by: Simon Horman <horms@verge.net.au>
In preparation for not including sysctl_sync_ver in
struct netns_ipvs when CONFIG_SYCTL is not defined.
Signed-off-by: Simon Horman <horms@verge.net.au>
In preparation for not including sysctl_sync_threshold in
struct netns_ipvs when CONFIG_SYCTL is not defined.
Signed-off-by: Simon Horman <horms@verge.net.au>
In preparation for not including sysctl_nat_icmp_send in
struct netns_ipvs when CONFIG_SYCTL is not defined.
Signed-off-by: Simon Horman <horms@verge.net.au>
In preparation for not including sysctl_snat_reroute in
struct netns_ipvs when CONFIG_SYCTL is not defined.
Signed-off-by: Simon Horman <horms@verge.net.au>
Rename ip_vs_new_estimator to ip_vs_start_estimator
and ip_vs_kill_estimator to ip_vs_stop_estimator to better
match their logic.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Move the estimator reading from estimation_timer to user
context. ip_vs_read_estimator() will be used to decode the rate
values. As the decoded rates are not set by estimation timer
there is no need to reset them in ip_vs_zero_stats.
There is no need ip_vs_new_estimator() to encode stats
to rates, if the destination is in trash both the stats and the
rates are inactive.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Remove ustats_seq, IPVS_STAT_INC and IPVS_STAT_ADD
because they are not used. They were replaced with u64_stats.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Currently, the new percpu counters are not zeroed and
the zero commands do not work as expected, we still show the old
sum of percpu values. OTOH, we can not reset the percpu counters
from user context without causing the incrementing to use old
and bogus values.
So, as Eric Dumazet suggested fix that by moving all overhead
to stats reading in user context. Do not introduce overhead in
timer context (estimator) and incrementing (packet handling in
softirqs).
The new ustats0 field holds the zero point for all
counter values, the rates always use 0 as base value as before.
When showing the values to user space just give the difference
between counters and the base values. The only drawback is that
percpu stats are not zeroed, they are accessible only from /proc
and are new interface, so it should not be a compatibility problem
as long as the sum stats are correct after zeroing.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
The global tot_stats contains cpustats field just like the
stats for dest and svc, so better use it to simplify the usage
in estimation_timer. As tot_stats is registered as estimator
we can remove the special ip_vs_read_cpu_stats call for
tot_stats. Fix ip_vs_read_cpu_stats to be called under
stats lock because it is still used as synchronization between
estimation timer and user context (the stats readers).
Also, make sure ip_vs_stats_percpu_show reads properly
the u64 stats from user context.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Remove include/net/netns/ip_vs.h because it depends on
structures from include/net/ip_vs.h. As ipvs is pointer in
struct net it is better to move struct netns_ipvs into
include/net/ip_vs.h, so that we can easily use other structures
in struct netns_ipvs.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
There's no sense to 'ct = ct = ' in ip_vs_notrack(). Just assign
nf_ct_get()'s return value directly to the pointer variable 'ct' once.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Simon Horman <horms@verge.net.au>
