As the mioa701 board has a M-Systems DiskOnChip G3 chip, add
it to the platform resources of the board.
Signed-off-by: Robert Jarzmik <robert.jarzmik@atosorigin.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Instead of reshuffling what functions in the pinmux paths should be
__init and thus could keep references to __initdata, let's just remove
the annotations for now -- the tables are moving to device tree in the
next version anyway and the whole subsystem is being wired up. We will
go back and re-annotate where appropriate once things settle down.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Currently, the Tegra pinmux is initialized at different times when booting
with and without device tree:
Without device tree:
1) Pinmux and GPIO drivers are registered.
2) Pinmux is configured.
3) All other drivers are registered.
With device tree:
1) All drivers are registered and probed, including pinmux and GPIO.
2) Pinmux is configured.
This change modifies board-pinmux.c to detect pinmux and GPIO driver
registration using bus notifiers. This allows pinmux configuration to
happen immediately after the pinmux driver is probed, irrespective of
whether the pinmux driver is manually registered by board-pinmux.c, or
if it's instantiated during device tree parsing.
To support this with device tree, the pinmux init functions must be
called prior to instantiating devices from device tree, so that the
notifiers are set up before-hand.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This moves the implementation of *_pinmux_init() into a single location.
The board-specific pinmux data is left in each board's own file. This
will allow future changes that set up the pinmux in a more complex
fashion to do so without duplicating that code in each board's pinmux
file.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pin group PTA does not support function RSVD3. However, the current
pinmux driver doesn't check this when setting RSVD functions, and ends
up writing 3 to the HW register. 3 is actually represented by function
GMI, so update the pinmux table to request that instead in order to
obtain the same register programming without requesting invalid
configurations.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Rather than modifying seaboard_pinmux[] using ventana_pinmux[], split
seaboard_pinmux[] into common_pinmux[] and seaboard_pinmux[], and then
actually apply common_pinmux[] always, followed by the appopriate one
of seaboard_pinmux[] or ventana_pinmux[].
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Some of the entries in ventana_pinmux[] are identical to what's already in
seaboard_pinmux[]. Remove the overrides from the Ventana table.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The Harmony pinmux table is already set up to mux the PCIe signals onto
the appropriate pin groups. Don't manually fiddle with the pinmux in the
Harmony PCIe setup code.
Merge note: This will have a merge conflict with Peter De Schrijver's
"arm/tegra: prepare pinmux code for multiple tegra variants" due to
context. When merging the two, make sure to also remove the include
of <mach/pinmux-tegra20.h> that his patch added, since it's no longer
needed after this patch.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The pinctrl device name is included in the pinctrl map table, and used
as a parameter to pin_config_*() functions. Hence, it must be the same
for non-DT and DT kernels. Add AUXDATA to cause this.
The GPIO device name will be used by the pinmux/GPIO initialization code
in a later patch, and needs to stay constant.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Seaboard and Ventana share some GPIOs, but others are different. Split the
GPIO table into common, seaboard-specific, and ventana-specific tables, so
that only the correct ones are enabled for each board. Add a few missing
audio-related GPIOs for Ventana.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
* samsung/board:
ARM: S3C64XX: Hook up VDDINT on Cragganmore
ARM: S3C2440: Add new LCD (W35i) support for Mini2440 board
ARM: S3C64XX: Power gate unused domains
ARM: S3C64XX: Hook up Littlemill audio card on Cragganmore
ARM: S3C64XX: Hook up platform data for Kilchomin module on Cragganmore
ARM: S3C64XX: Run Tobermory interrupts in the default mode
ARM: S3C64XX: Improve logging of unknown Cragganmore module types
ARM: S3C64XX: Configure WM1250 EV1 GPIOs on Cragganmore
ARM: S3C64XX: Use software initiated powerdown for Cragganmore
ARM: S3C64XX: Raise the frequency of the second I2C bus on Cragganmore
ARM: S3C64XX: Correct reservation of GPIOs for CPU module on Cragganmore
ARM: SAMSUNG: Fix GPIO space reservation for S3C64xx platforms
ARM: S3C64XX: Update for conversion to SAMSUNG_GPIO_EXTRA
Conflicts:
arch/arm/mach-s3c64xx/mach-crag6410.c
The Sabreauto board was renamed to Armadillo2 recently. To avoid
confusion, rename Sabreauto to Armadillo2/arm2.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The default phy RGMII pad settings can not work, tune pad skew.
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
UART1/UART2/... is more readable than UART0/UART1/... .
Remove redundant UART comments.
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
GPIO1/GPIO2/... is more readable than GPIO0/GPIO1/... .
Remove redundant gpio comments.
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Adding musb support in ti816 EVM board file.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding ti81xx_musb_phy_power() which will be used by musb driver through
its function pointer in board_data.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Added musb support for ti81xx platform which has two instances of musb
interface and uses CPPI4.1 DMA. The current patch set adds support for
single instance and in PIO mode only.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds minimal support and build configuration for TI8148 EVM. Also
adds support for low level debugging on UART1 console on the EVM.
Note that existing TI8168 EVM file (board-ti8168evm.c) is updated with machine
info for TI8148 EVM.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4 SDP/Blaze boards have onboard digital microphones.
Register the platform device for the dmic-codec to be
able to use the microphones.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add memory timing info regarding the 200 MHz memory in sdram-nokia.
Note that 100 MHz mode uses these same timings too.
Signed-off-by: Igor Dmitriev <ext-dmitriev.igor@nokia.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
[tony@atomide.com: updated comments for 100 MHz timings]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable TSC2005 touchscreen driver on the RX-51 board by providing the
needed platform data.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Reviewed-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP pin mux configuration API has been used incorrectly resulting
in wrong mux mode set for several DSS pins.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
USB hub is not functional until is reset.
Reset the USB hub on SB-T35.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[tony@atomide.com: updated subject]
Signed-off-by: Tony Lindgren <tony@atomide.com>
TWL4030 audio codec is not being registered if no platform data is
supplied. Provide platform data for the TWL4030 audio codec.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[tony@atomide.com: updated subject]
Signed-off-by: Tony Lindgren <tony@atomide.com>
cm-t35 DSS suplies are connected to VIO.
In fact, TPS65930 does not have VPLL2.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[tony@atomide.com: updated subject]
Signed-off-by: Tony Lindgren <tony@atomide.com>
ads7846 driver fails to find the regulator supply and
as a result the touchscreen is not working.
Fix this by adding a regulator supply for the ads7846 driver.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[tony@atomide.com: updated subject]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds cpu type, macros for identification of TI814X device.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
[tony@atomide.com: left out CK_TI814X for now]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates existing macros, functions used for TI816X, to enable
addition of other SoCs belonging to TI81XX family (e.g., TI814X).
The approach taken is to use TI81XX/ti81xx for code/data going to be common
across all TI81XX devices.
cpu_is_ti81xx() is introduced to handle code common across TI81XX devices.
In addition, ti8168_evm_map_io() is now replaced with ti81xx_map_io() and moved
in mach-omap2/common.c as same will be used for TI814X and is not board
specific.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
allow for the omap4430 es2.3 revision to be recognized in the
omap4_check_revision() function.
most aspects of all omap4430 es2.x versions are identical, however
a number of small variations such as default pullup or pulldown
resistor configurations vary between revisions.
detailed information on silicon errata for omap4430 revisions can
be found at http://focus.ti.com/pdfs/wtbu/swpz009D.pdf
Signed-off-by: David Anders <x0132446@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates the common machine specific source files for
support for AM33XX/AM335x with cpu type, macros for identification of
AM33XX/AM335X device.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
[tony@atomide.com: updated for map_io and common.h changes, dropped CK_AM33XX]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates the common platform files with AM335X device
support (AM33XX family).
The approach taken in this patch is,
AM33XX device will be considered as OMAP3 variant, and a separate
SoC class created for AM33XX family of devices with a subclass type
for AM335X device, which is newly added device in the family.
This means, cpu_is_omap34xx(), cpu_is_am33xx() and cpu_is_am335x()
checks will return success on AM335X device.
A kernel config option CONFIG_SOC_OMAPAM33XX is added under OMAP3
to include support for AM33XX build.
Also, cpu_mask and RATE_IN_XXX flags have crossed 8 bit hence
struct clksel_rate.flags, struct prcm_config.flags and cpu_mask
are changed to u16 from u8.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Hemant Pedanekar <hemantp@ti.com>
[tony@atomide.com: left out CK_AM33XX for now]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that there is a common way to reset the machine, let's use it
instead of reinventing the wheel in the kexec backend.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Sending IPI_CPU_STOP to a CPU causes it to execute a busy cpu_relax
loop forever. This makes it impossible to kexec successfully on an SMP
system since the secondary CPUs do not reset.
This patch adds a callback to platform_cpu_kill, defined when
CONFIG_HOTPLUG_CPU=y, from the ipi_cpu_stop handling code. This function
currently just returns 1 on all platforms that define it but allows them
to do something more sophisticated in the future.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Tools such as kexec and CPU hotplug require a way to reset the processor
and branch to some code in physical space. This requires various bits of
jiggery pokery with the caches and MMU which, when it goes wrong, tends
to lock up the system.
This patch fleshes out the soft_restart implementation so that it
branches to the reset code using the identity mapping. This requires us
to change to a temporary stack, held within the kernel image as a static
array, to avoid conflicting with the new view of memory.
Signed-off-by: Will Deacon <will.deacon@arm.com>
When disabling the MMU, it is necessary to take out a 1:1 identity map
of the reset code so that it can safely be executed with and without
the MMU active. To avoid the situation where the physical address of the
reset code aliases with the virtual address of the active stack (which
cannot be included in the 1:1 mapping), it is desirable to change to a
new stack at a location which is less likely to alias.
This code adds a new lib function, call_with_stack:
void call_with_stack(void (*fn)(void *), void *arg, void *sp);
which changes the stack to point at the sp parameter, before invoking
fn(arg) with the new stack selected.
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When probing the VIC, the ST variant has a different probing method to
account for the extra interrupts which meant we didn't previously call
vic_register() which registered the irq_domain.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
