The RTC hwmod on AM335x family of SoCs is unique in that the
clkctrl_offs in the PRCM is 0. We rely on a clkctrl_offs of zero as
indicating no clkctrl is present so we must flag this hwmod with
HWMOD_OMAP4_ZERO_CLKCTRL_OFFSET to indicate the 0 clkctrl_offs is in
fact valid in this case.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Nearly all modules on OMAP4 and newer platforms have clkctrl offsets
that are non-zero except for the RTC on am335x. Because we rely on a
clkctrl_offset of zero to indicate no clkctrl_offset being present,
lets add a HWMOD_OMAP4_ZERO_CLKCTRL_OFFSET flag to use to indicate
hwmods that have a valid clkctrl_offset of 0.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add missing sysconfig/sysstatus information
to OMAP3 hwmod. The information has been
checked against OMAP34xx and OMAP36xx TRM.
Without this change DSI block is not reset
during boot, which is required for working
Nokia N950 display.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
If the module has no clkctrl register defined, module_wait_ready should
not try to access this. This can potentially cause an illegal register
access, and result in bad idle reporting also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The previous implementation was racy in many locations, where the current
status of the clockdomain was read out, some operations were executed,
and the previous status info was used afterwards to decide next state
for the clockdomain. Instead, fix the implementation of the allow_idle /
deny_idle APIs to properly have usecounting support. This allows clean
handling internally within the clockdomain core, and simplifies the
usage also within hwmod.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the introduction of hwmod module clocks, the name of the hwmod
main clk may not be available before hwmod setup, as hwmod setup
may lookup the main clock dynamically based on the hwmod name.
Thus, change the order of hwmod setup and main clock handling for
the timer code, to make sure the main clock is going to be
available.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the transition to hwmod module clocks, all hwmods will have
their main clocks named <hwmod_name>_mod_ck. Use this info to
fetch main_clk, and use it if found.
Also, if a main_clk is found based on the hwmod name, disable
the direct PRCM modulemode access from hwmod.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This avoids the need to add most of the clock aliases under
drivers/clk/ti/clk-xyz.c files.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I found one more make randconfig build error with the recent
SMP kexec changes. We need the mpuss now always available early.
Fixes: 0573b957fc ("ARM: OMAP4+: Prevent CPU1 related hang
with kexec")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like I only partially fixed up things if CONFIG_SMP
is not set for the recent kexec changes. We don't have
boot_secondary available without SMP as reported by Arnd.
Fixes: 0573b957fc ("ARM: OMAP4+: Prevent CPU1 related hang with kexec")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to reset CPU1 properly for kexec when booting different
kernel versions. Otherwise CPU1 will attempt to boot the the
previous kernel's start_secondary(). Note that the restctrl
register is different from the low-power mode wakeup register
CPU1_WAKEUP_NS_PA_ADDR. We need to configure both.
Let's fix the issue by defining SoC specific data to initialize
things in a more generic way. And let's also standardize omap-smp.c
to use soc_is instead of cpu_is while at it.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Kexec booted kernels on omap4 will hang early during the boot if the
booted kernel is different version from the previous kernel.
This is because the previous kernel may have configured low-power mode
using CPU1_WAKEUP_NS_PA_ADDR. In that case it points to the previous
kernel's omap4_secondary_startup(), and CPU1 can be in low power mode
from the previous kernel. When the new kernel configures the CPU1
clockdomain, CPU1 can wake from low power state prematurely during
omap44xx_clockdomains_init() running random code.
Let's fix the issue by configuring CPU1_WAKEUP_NS_PA_ADDR before we
call omap44xx_clockdomains_init(). Note that this is very early during
the init, and we will do proper CPU1 reset during SMP init a bit later
on in omap4_smp_prepare_cpus(). And we need to do this when SMP is
not enabled as the previous kernel may have had it enabled.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Prepare things for making kexec work on SMP omap variants by initializing
SARM RAM base early. This allows us to configure CPU1 for kexec in case
the previous kernel has put CPU1 in low power mode.
Note that this should not prevent moving other SAR RAM code to live
under drivers. However for kexec, we will need this very early.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per the TRM: http://www.ti.com/lit/ug/spruh73m/spruh73m.pdf
offset 0x4 is reserved for PRM_PER. Hence removing the wrongly
defined address offset.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The ti81xx_rtc_hwmod is not exported, or declared outside the file
arch/arm/mach-omap2/omap_hwmod_81xx_data.c so make it static to
avoid the following warning:
arch/arm/mach-omap2/omap_hwmod_81xx_data.c:246:19: warning: symbol 'ti81xx_rtc_hwmod' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
pruss hwmod RSTST register wrongly points to PWRSTCTRL register in case of
am43xx. Fix the RSTST register offset value.
This can lead to setting of wrong power state values for PER domain.
Fixes: 1c7e224d ("ARM: OMAP2+: hwmod: AM335x: runtime register update")
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The addresses for DSS are provided in the DT data, so they can be
removed from the hwmod.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
QSPI address space information is passed from device tree. Therefore
remove legacy way of passing address space via hwmod data.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The new pdata callback (force_ick_on) is now used by the driver and the old
callback related code can be removed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The McBSP sidetone (in OMAP3 McBSP2 and 3 module) is working with the
module's interface clock. When the sidetone is enabled the iclk must not
idle because it will result in choppy sidetone.
Switch to use the new callback for handling the iclk allow/deny idle
configuration.
For this the driver needs to get the module's ick clock and pass the clk
pointer to the callback.
In DT boot, the pdata-quirk is going to set up the callback for the driver
so save it if it is set in the pdata of the device.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The function will do more then removing the sysfs files in the future.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McBSP2/3 module's sidetone module operates using the module's ICLK clock.
When the Sidetone is in use the interface clock of the module must not
idle. To prevent the iclk idling the driver expects to have pdata callback
to call. With this patch the callback is going to be set up for DT boot
also.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McBSP2/3 module's sidetone module operates using the module's ICLK clock.
When the Sidetone is in use the interface clock of the module must not
idle. The new callback expects to receive the *clk of the module's ick and
not the id number of the McBSP. This will allow us more cleanups and going
to simplify the ICLK handling.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The McBSPLP's sidetone main clock is the McBSPLP's ICLK, not FCLK as the
sidetone only receives the ICLK from the main McBSP module.
Since the McBSP and sidetone is using the very same clock from PRCM level
the sidetone must not have the prcm section to check the clock status since
the sidetone is only used when McBSP is already configured.
If two separate hwmods looking at the same bit and they would use
pm_runtime in nested way (as it must happen with McBSP and it's ST module)
the hwmod would warn, because the idlest will not match what it is expected
after enable/disable of the clocks.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Devices that utilize the OCP registers and/or PRCM registers and
register bit fields should be modeled using hwmod. Since eQEP, ePWM and
eCAP don't fall under this category, remove their hwmod entries.
Instead these clocks simply use the clock that is passed through by its
parent PWMSS. Therefore, PWMSS handles the clock for itself and its
subdevices.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add tblck to the pwm nodes. This insures that the ehrpwm driver has access
to the time-based clk.
Do not remove similar entries for ehrpwm node. Later patches will switch
from using ehrpwm node name to pwm. But to maintain ABI compatibility we
shouldn't remove the old entries.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Instead of the full omapdss internal header, include only the platform_data
header.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The omap_display_init() is implemented in the mach-omap2/display.c so the
declaration should have been there as well.
Change the board files to include display.h to avoid build breakage at the
same time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
OMAP_DSS_VENC_TYPE_COMPOSITE is 0. There is no need to explicitly set the
connector_type.
This change is needed for the omapdss header cleanup.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The self-test was updated to cover zero-length strings; the function
needs to be updated, too.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: George Spelvin <linux@sciencehorizons.net>
Fixes: fcfd2fbf22 ("fs/namei.c: Add hashlen_string() function")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The original name was simply hash_string(), but that conflicted with a
function with that name in drivers/base/power/trace.c, and I decided
that calling it "hashlen_" was better anyway.
But you have to do it in two places.
[ This caused build errors for architectures that don't define
CONFIG_DCACHE_WORD_ACCESS - Linus ]
Signed-off-by: George Spelvin <linux@sciencehorizons.net>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Fixes: fcfd2fbf22 ("fs/namei.c: Add hashlen_string() function")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The HPFS filesystem used generic_show_options to produce string that is
displayed in /proc/mounts. However, there is a problem that the options
may disappear after remount. If we mount the filesystem with option1
and then remount it with option2, /proc/mounts should show both option1
and option2, however it only shows option2 because the whole option
string is replaced with replace_mount_options in hpfs_remount_fs.
To fix this bug, implement the hpfs_show_options function that prints
options that are currently selected.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit c8f33d0bec ("affs: kstrdup() memory handling") checks if the
kstrdup function returns NULL due to out-of-memory condition.
However, if we are remounting a filesystem with no change to
filesystem-specific options, the parameter data is NULL. In this case,
kstrdup returns NULL (because it was passed NULL parameter), although no
out of memory condition exists. The mount syscall then fails with
ENOMEM.
This patch fixes the bug. We fail with ENOMEM only if data is non-NULL.
The patch also changes the call to replace_mount_options - if we didn't
pass any filesystem-specific options, we don't call
replace_mount_options (thus we don't erase existing reported options).
Fixes: c8f33d0bec ("affs: kstrdup() memory handling")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit ce657611ba ("hpfs: kstrdup() out of memory handling") checks if
the kstrdup function returns NULL due to out-of-memory condition.
However, if we are remounting a filesystem with no change to
filesystem-specific options, the parameter data is NULL. In this case,
kstrdup returns NULL (because it was passed NULL parameter), although no
out of memory condition exists. The mount syscall then fails with
ENOMEM.
This patch fixes the bug. We fail with ENOMEM only if data is non-NULL.
The patch also changes the call to replace_mount_options - if we didn't
pass any filesystem-specific options, we don't call
replace_mount_options (thus we don't erase existing reported options).
Fixes: ce657611ba ("hpfs: kstrdup() out of memory handling")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Various builds (such as i386:allmodconfig) fail with
fs/binfmt_aout.c:133:2: error: expected identifier or '(' before 'return'
fs/binfmt_aout.c:134:1: error: expected identifier or '(' before '}' token
[ Oops. My bad, I had stupidly thought that "allmodconfig" covered this
on x86-64 too, but it obviously doesn't. Egg on my face. - Linus ]
Fixes: 5d22fc25d4 ("mm: remove more IS_ERR_VALUE abuses")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull string hash improvements from George Spelvin:
"This series does several related things:
- Makes the dcache hash (fs/namei.c) useful for general kernel use.
(Thanks to Bruce for noticing the zero-length corner case)
- Converts the string hashes in <linux/sunrpc/svcauth.h> to use the
above.
- Avoids 64-bit multiplies in hash_64() on 32-bit platforms. Two
32-bit multiplies will do well enough.
- Rids the world of the bad hash multipliers in hash_32.
This finishes the job started in commit 689de1d6ca ("Minimal
fix-up of bad hashing behavior of hash_64()")
The vast majority of Linux architectures have hardware support for
32x32-bit multiply and so derive no benefit from "simplified"
multipliers.
The few processors that do not (68000, h8/300 and some models of
Microblaze) have arch-specific implementations added. Those
patches are last in the series.
- Overhauls the dcache hash mixing.
The patch in commit 0fed3ac866 ("namei: Improve hash mixing if
CONFIG_DCACHE_WORD_ACCESS") was an off-the-cuff suggestion.
Replaced with a much more careful design that's simultaneously
faster and better. (My own invention, as there was noting suitable
in the literature I could find. Comments welcome!)
- Modify the hash_name() loop to skip the initial HASH_MIX(). This
would let us salt the hash if we ever wanted to.
- Sort out partial_name_hash().
The hash function is declared as using a long state, even though
it's truncated to 32 bits at the end and the extra internal state
contributes nothing to the result. And some callers do odd things:
- fs/hfs/string.c only allocates 32 bits of state
- fs/hfsplus/unicode.c uses it to hash 16-bit unicode symbols not bytes
- Modify bytemask_from_count to handle inputs of 1..sizeof(long)
rather than 0..sizeof(long)-1. This would simplify users other
than full_name_hash"
Special thanks to Bruce Fields for testing and finding bugs in v1. (I
learned some humbling lessons about "obviously correct" code.)
On the arch-specific front, the m68k assembly has been tested in a
standalone test harness, I've been in contact with the Microblaze
maintainers who mostly don't care, as the hardware multiplier is never
omitted in real-world applications, and I haven't heard anything from
the H8/300 world"
* 'hash' of git://ftp.sciencehorizons.net/linux:
h8300: Add <asm/hash.h>
microblaze: Add <asm/hash.h>
m68k: Add <asm/hash.h>
<linux/hash.h>: Add support for architecture-specific functions
fs/namei.c: Improve dcache hash function
Eliminate bad hash multipliers from hash_32() and hash_64()
Change hash_64() return value to 32 bits
<linux/sunrpc/svcauth.h>: Define hash_str() in terms of hashlen_string()
fs/namei.c: Add hashlen_string() function
Pull out string hash to <linux/stringhash.h>
This will improve the performance of hash_32() and hash_64(), but due
to complete lack of multi-bit shift instructions on H8, performance will
still be bad in surrounding code.
Designing H8-specific hash algorithms to work around that is a separate
project. (But if the maintainers would like to get in touch...)
Signed-off-by: George Spelvin <linux@sciencehorizons.net>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: uclinux-h8-devel@lists.sourceforge.jp
