The bonding driver calls ndo_vlan_rx_register() while holding bond->lock.
The bnx2 driver calls bnx2_netif_stop() to stop the rx handling while
changing the vlgrp. The call also stops the cnic driver which sleeps
while the bond->lock is held and cause the warning.
This code path only needs to stop the NAPI rx handling while we are
changing the vlgrp. Since no reset is going to occur, there is no need
to stop cnic in this case. By adding a parameter to bnx2_netif_stop()
to skip stopping cnic, we can avoid the warning.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It has been reported that under certain heavy traffic conditions in MSI-X
mode, the driver can lose an MSI-X vector causing all packets in the
associated rx/tx ring pair to be dropped. The problem is caused by
the chip dropping the write to unmask the MSI-X vector by the kernel
(when migrating the IRQ for example).
This can be prevented by increasing the GRC timeout value for these
register read and write operations.
Thanks to Dell for helping us debug this problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some Power7 platforms, when using VIOS (Virtual I/O Server), we
need to wait longer for control packets to finish transfer during
initialization.
Without this change, initialization may fail prematurely.
Signed-off-by: Wen Xiong <wenxiong@us.ibm.com>
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prompted by a previous patch submitted by Matthew Garret <mjg@redhat.com>,
further digging into errata documentation reveals the current enabling or
disabling of ASPM L0s and L1 states for certain parts supported by this
driver are incorrect. 82571 and 82572 should always disable L1. For
standard frames, 82573/82574/82583 can enable L1 but L0s must be disabled,
and for jumbo frames 82573/82574 must disable L1. This allows for some
parts to enable L1 in certain configurations leading to better power
savings.
Also according to the same errata, Early Receive (ERT) should be disabled
on 82573 when using jumbo frames.
Cc: Matthew Garret <mjg@redhat.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY laser is still on during driver init. It's allowing
garbage to hit our FIFO, which eventually can cause the entire
device to die. Power down the laser while setting up the device,
and re-enable the laser before getting link.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
78f1cd0245 ("fix broken register writes")
does not work for Al Viro's r8169 (XID 18000000).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Few (6) network drivers enable mwi explicitly. Fewer worry about a
failure.
It is not a fix but it should avoid some annoyance like
http://bugzilla.kernel.org/show_bug.cgi?id=15454
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Conrad Kostecki <conikost@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even with commit 32dec5dd02 ("bridge
br_multicast: Don't refer to BR_INPUT_SKB_CB(skb)->mrouters_only
without IGMP snooping."), BR_INPUT_SKB_CB(skb)->mrouters_only is
not appropriately initialized if IGMP snooping support is
compiled and disabled, so we can see garbage.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trying to run izlisten (from lowpan-tools tests) on a device that does not
exists I got the oops below. The problem is that we are using get_dev_by_name
without checking if we really get a device back. We don't in this case and
writing to dev->type generates this oops.
[Oops code removed by Dmitry Eremin-Solenikov]
If possible this patch should be applied to the current -rc fixes branch.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3: Fix INTx fallback when MSI fails
MSI setup changes the value of irq_vec in struct tg3 *tp.
This attribute must be taken into account and restored before
we try to do a new request_irq for INTx fallback.
In powerpc, the original code was leading to an EINVAL return within
request_irq, because the driver was trying to use the disabled MSI
virtual irq number instead of tp->pdev->irq.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit fda48a0d7a (tcp: bind() fix when many ports are bound)
introduced a bug on IPV6 part.
We should not call ipv6_addr_any(inet6_rcv_saddr(sk2)) but
ipv6_addr_any(inet6_rcv_saddr(sk)) because sk2 can be IPV4, while sk is
IPV6.
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing stops the workqueue being left to run in parallel with close or a
few other operations. This causes double unmaps and the like.
See kerneloops.org #1041230 for an example
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gianfar driver may pass NULL pointer to the of_translate_address(),
which may lead to a kernel oops. Fix this by using of_iomap(), which
is also much simpler and shorter.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Old P1020RDB device trees were not specifing tbipa address for
MDIO nodes, which is now causing this kernel oops:
...
eth2: TX BD ring size for Q[6]: 256
eth2: TX BD ring size for Q[7]: 256
Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc0015504
Oops: Kernel access of bad area, sig: 11 [#1]
...
NIP [c0015504] memcpy+0x3c/0x9c
LR [c000a9f8] __of_translate_address+0xfc/0x21c
Call Trace:
[df839e00] [c000a94c] __of_translate_address+0x50/0x21c (unreliable)
[df839e50] [c01a33e8] get_gfar_tbipa+0xb0/0xe0
...
The old device trees are buggy, though having a dead ethernet is
better than a dead kernel, so fix the issue by using of_iomap().
Also, a somewhat similar issue exist in the probe() routine, though
there the oops is only a possibility. Nonetheless, fix it too.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port autoselection done by kernel only works when number of bound
sockets is under a threshold (typically 30000).
When this threshold is over, we must check if there is a conflict before
exiting first loop in inet_csk_get_port()
Change inet_csk_bind_conflict() to forbid two reuse-enabled sockets to
bind on same (address,port) tuple (with a non ANY address)
Same change for inet6_csk_bind_conflict()
Reported-by: Gaspar Chilingarov <gasparch@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original code, the "goto out" calls "rdma_destroy_id(cm_id);"
That isn't needed here and would cause problems because "cm_id" is an
ERR_PTR. The new code just returns directly.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original code, if rtnl_create_link() returned an ERR_PTR then that
would get passed to rtnl_configure_link() which dereferences it.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The issue raises when having 2 NICs both assigned the same
IPv6 global address.
If a sender binds to a particular NIC (SO_BINDTODEVICE),
the outgoing traffic is being sent via the first found.
The bonded device is thus not taken into an account during the
routing.
From the ip6_route_output function:
If the binding address is multicast, linklocal or loopback,
the RT6_LOOKUP_F_IFACE bit is set, but not for global address.
So binding global address will neglect SO_BINDTODEVICE-binded device,
because the fib6_rule_lookup function path won't check for the
flowi::oif field and take first route that fits.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Scott Otto <scott.otto@alcatel-lucent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to RFC2460, PMTU is set to the IPv6 Minimum Link
MTU (1280) and a fragment header should always be included
after a node receiving Too Big message reporting PMTU is
less than the IPv6 Minimum Link MTU.
After receiving a ICMPv6 Too Big message reporting PMTU is
less than the IPv6 Minimum Link MTU, sctp *can't* send any
data/control chunk that total length including IPv6 head
and IPv6 extend head is less than IPV6_MIN_MTU(1280 bytes).
The failure occured in p6_fragment(), about reason
see following(take SHUTDOWN chunk for example):
sctp_packet_transmit (SHUTDOWN chunk, len=16 byte)
|------sctp_v6_xmit (local_df=0)
|------ip6_xmit
|------ip6_output (dst_allfrag is ture)
|------ip6_fragment
In ip6_fragment(), for local_df=0, drops the the packet
and returns EMSGSIZE.
The patch fixes it with adding check length of skb->len.
In this case, Ipv6 not to fragment upper protocol data,
just only add a fragment header before it.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new driver to use tethering with an iPhone device. After initial submission,
apply fixes to fit the new driver into the kernel standards.
There are still a couple of minor (almost cosmetic-level) issues, but the driver
is fully functional right now.
Signed-off-by: L. Alberto Giménez <agimenez@sysvalve.es>
Signed-off-by: Diego Giagio <diego@giagio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I encountered an issue that not to link up on cxgb3 fabric.
I bisected and found that this regression was introduced by
0f07c4ee8c.
Correct to pass phy_addr to cphy_init() at t3_xaui_direct_phy_prep().
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1, An X25 program binds and listens
2, calls arrive waiting to be accepted
3, Program exits without accepting
4, Sockets time out but don't get correctly cleaned up
5, cat /proc/net/x25/socket shows the dead sockets with bad inode fields.
This line borrowed from AX25 sets the dying socket so the timers clean up later.
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix NULL pointer dereference in ks8851_tx_work by checking if dequeued
list is already empty before writing the packet to TX FIFO
Unable to handle kernel NULL pointer dereference at virtual address 00000050
PC is at ks8851_tx_work+0xdc/0x1b0
LR is at wait_for_common+0x148/0x164
pc : [<c01c0df4>] lr : [<c025a980>] psr: 20000013
Backtrace:
ks8851_tx_work+0x0/0x1b0
worker_thread+0x0/0x190
kthread+0x0/0x90
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the stats counter calculation in 3c574_cs, similar
to the method used in 3c589_cs. This corrects the contents
of the counter on tests using a "Megahertz 574B" card.
[linux@dominikbrodowski.net: clean up commit message]
Signed-off-by: Alexander Kurz <linux@kbdbabel.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building a bundle, we set dst.dev and rt6.rt6i_idev.
We must ensure to set the same device for both fields.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ems_usb_probe(), a pointer is dereferenced after making sure it is NULL...
This patch replaces netdev->dev.parent with &intf->dev in dev_err() calls to
avoid this.
Signed-off-by: "Hans J. Koch" <hjk@linutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My recent patch to remove the open-coded checksum sequence in
tcp_v6_send_response broke it as we did not set the transport
header pointer on the new packet.
Actually, there is code there trying to set the transport
header properly, but it sets it for the wrong skb ('skb'
instead of 'buff').
This bug was introduced by commit
a8fdf2b331 ("ipv6: Fix
tcp_v6_send_response(): it didn't set skb transport header")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
grec_nsrcs is in network order, we should convert to host horder in
br_multicast_igmp3_report()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make __DQUOT_PARANOIA define from the old days a standard config option
and turn it off by default.
This gets rid of a quota warning about writes before quota is turned on
for systems with ext4 root filesystem. Currently there's no way to legally
solve this because /etc/mtab has to be written before quota is turned on
on most systems.
Signed-off-by: Jan Kara <jack@suse.cz>
* 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: fix error handling in cm4000_cs.c
drivers/pcmcia: Add missing local_irq_restore
serial_cs: MD55x support (PCMCIA GPRS/EDGE modem) (kernel 2.6.33)
pcmcia: avoid late calls to pccard_validate_cis
pcmcia: fix ioport size calculation in rsrc_nonstatic
pcmcia: re-start on MFC override
pcmcia: fix io_probe due to parent (PCI) resources
pcmcia: use previously assigned IRQ for all card functions
Before commit e28cbf2293 ("improve
sys_newuname() for compat architectures") 64-bit x86 had a private
implementation of sys_uname which was just called sys_uname, which other
architectures used for the old uname.
Due to some merge issues with the uname refactoring patches we ended up
calling the old uname version for both the old and new system call
slots, which lead to the domainname filed never be set which caused
failures with libnss_nis.
Reported-and-tested-by: Andy Isaacson <adi@hexapodia.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We can overflow the hardirq stack if we set the %pil here
so early, just let the normal control flow do it.
This is fine as we are allowed to do the actual IRQ enable
at any point after we call trace_hardirqs_on.
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers may use vblank calls now (e.g. drm_vblank_off) in their unload
paths, so don't clean up the vblank related structures until after
driver unload.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The recent anon_vma fixes cause many anonymous pages to end up
in the parent process anon_vma, even when the page is exclusively
owned by the current process.
Adding exclusively owned anonymous pages to the top anon_vma
reduces rmap scanning overhead, especially in workloads with
forking servers.
This patch adds a parameter to __page_set_anon_rmap that can
be used to indicate whether or not the added page is exclusively
owned by the current process.
Pages added through page_add_new_anon_rmap are exclusively
owned by the current process, and can be added to the top
anon_vma.
Pages added through page_add_anon_rmap can be either shared
or exclusively owned, so we do the conservative thing and
add it to the oldest anon_vma.
A next step would be to add the exclusive parameter to
page_add_anon_rmap, to be used from functions where we do
know for sure whether a page is exclusively owned.
Signed-off-by: Rik van Riel <riel@redhat.com>
Reviewed-by: Johannes Weiner <hannes@cmpxchg.org>
Lightly-tested-by: Borislav Petkov <bp@alien8.de>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
[ Edited to look nicer - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ecryptfs/ecryptfs-2.6:
eCryptfs: Turn lower lookup error messages into debug messages
eCryptfs: Copy lower directory inode times and size on link
ecryptfs: fix use with tmpfs by removing d_drop from ecryptfs_destroy_inode
ecryptfs: fix error code for missing xattrs in lower fs
eCryptfs: Decrypt symlink target for stat size
eCryptfs: Strip metadata in xattr flag in encrypted view
eCryptfs: Clear buffer before reading in metadata xattr
eCryptfs: Rename ecryptfs_crypt_stat.num_header_bytes_at_front
eCryptfs: Fix metadata in xattr feature regression
Since "mac80211: make off-channel work generic" drivers have not been
notified of configuration changes after association or authentication. This
caused more dependence on current state to ensure driver will be notified
when configuration changes occur. One such problem arises if off-channel is
in progress when HT information changes. Since HT is only enabled on the
"oper_channel" the driver will never be notified of this change. Usually
the driver is notified soon after of a BSS information change
(BSS_CHANGED_HT) ... but since the driver did not get a notification that
this is a HT channel the new BSS information does not make sense.
Fix this by also changing the off-channel information when HT is enabled
and thus cause driver to be notified correctly.
This fixes a problem in 4965 when associated with 5GHz 40MHz channel.
Without this patch the system can associate but is unable to transfer any
data, not even ping.
See http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2158
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the addba timer expires but has no work to do,
it should not affect the state machine. If it does,
TX will not see the successfully established and we
can also crash trying to re-establish the session.
Cc: stable@kernel.org [2.6.32, 2.6.33]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vaugue warnings about ENAMETOOLONG errors when looking up an encrypted
file name have caused many users to become concerned about their data.
Since this is a rather harmless condition, I'm moving this warning to
only be printed when the ecryptfs_verbosity module param is 1.
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
