Patch from Andrew Victor
This patch removes the now unnecessary
include/asm-arm/arch-at91rm9200/pio.h file. The pin configuration is
now handled in the platform-device setup code
(arch/arm/mach-at91rm9200/devices.c).
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch includes a number of updates to the AT91RM9200 serial driver.
Changes include:
1. Conversion to a platform_driver. [Ivan Kokshaysky]
2. Replaced all references to AT91RM9200 with AT91. This driver can now
also be used for the AT91SAM9216.
3. Allow TIOCM_LOOP to configure local loopback mode.
4. Cleaned up the 'read_status_mask' usage and interrupt handler code.
[Chip Coldwell]
5. Suspend/resume support. [David Brownell]
There are a few 'unused variable' warning when compiling this - I
removed the new DMA support to keep this first patch simpler.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch includes the structures and exported functions required for
the platform-device support (added in patch 3585/1).
Also adds the arch_identify() function for run-time detection of which
AT91 processor the code is running on. [Original patch from Ivan
Kokshaysky]
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch updates the support for the Atmel DK and EK boards.
The changes include:
1. Use the new at91_uart_config structure and device registration
functions for the UARTs.
2. Registration of I2C and SPI platform devices.
3. The USB Device pullup line is connected to reset, so multidrive needs
to be enabled on the line. [Patch from David Brownell].
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch updates the support for the Cogent CSB337 and CSB637 boards.
The changes include:
1. Use the new at91_uart_config structure and device registration
functions for the UARTs.
2. Registration of I2C and SPI platform devices.
3. The CSB337 board uses PB0 & PB1 (and not PB2) for the LEDs. [Patch
from David Brownell]
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
These headers define the registers and bits for the SPI (Serial
Peripheral Interface), SSC (Synchronous Serial), TC (Timer/Counter) and
UDP (USB Device) peripherals integrated in the AT91RM9200 processor.
(They will probably also be usable for the AT91SAM9 series of SoC
processors)
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
Added definition for the bits in the Chip ID register.
Corrected the capitalization of AT91_RTC_AMPM register name.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch updates the platform device support for the AT91RM9200.
The changes include:
1. USB Host device renamed to "at91_ohci" since the driver is also
usable on the AT91SAM9261 processor.
2. Enabling multidrive on the USB Device's pullup pin should not be done
for all boards. Moved into board-specific files. [Patch from David
Brownell]
3. Move enabling of PCMCIA/Compact Flash pins out of the driver.
4. Added SPI device and resources.
5. Added Watchdog device and resources. [Patch from David Brownell]
6. Added UART device and resources.
7. The simple devices (watchdog, rtc, i2c) are now automatically
registered and don't have to be registered separately in each
board-specific file. [Patch from David Brownell]
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch adds suspend/resume/set_wake support for the AT91RM9200's
GPIO interrupts.
Original patch from David Brownell.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
Added suspend/resume/set_wake support for the AT91RM9200's AIC interrupt
controller.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
The AIC interrupt controller's set_irq_type() can also be used for
internal interrupts. IRQT_LOW and IRQT_FALLING are the only options not
supported for the internal interrupts.
[Original patch from Karl Olsen]
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch maps the AT91RM9200's internal SRAM into the virtual memory
address space - just below the internal peripheral registers.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
Added suspend/resume support for the AT91RM9200 timer.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
Use a global variable 'last_crtr' to store the time of the last timer
tick instead of the ST_RTAR register.
It's faster, frees up the ST_RTAR register for other uses, and hopefully
makes the code more understandable. [Patch from Peter Menzebach]
Also add the SA_TIMER flag to Timer IRQ. (It seems to be required for
the realtime preempt patch).
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
Some updates to the clock infrastructure for the AT91RM9200.
1. Hard-coded values replaced with names defined in at91rm9200_sys.h.
2. Added the four PIO clocks, which are enabled at startup.
3. At startup, disable all unused clocks.
4. Minor bugfix for usage counts associated with MCK. [Patch from David
Brownell]
5. Added at91_clock_associate() function to associate device & function
with a particular clock. [Patch from David Brownell]
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Set the default triggers for the LOCOMO LED driver.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Core support for the Samsung S3C2442, and the
serial port driver update to allow the serial
port blocks to be used.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
All the S3C24XX based devices currently have similar
uart blocks, in the same location. Make the process
of adding new uart blocks easier by commonising the
device definitions and adding a new init function
for the cpu code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Platform devices for the LEDs on all the SMDK24XX boards
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from David Brownell
This adds the platform device for SSP/SPI controller, and declares
the ads7846 device hooked up to it. Not all Lubbock boards appear
to populate the connector needed to use this instead of the ucb1400
chip, but it can always be used as a temperature sensor.
In short, this is probably most useful as an example of how to
provide the configuration data used by the pxa2xx_spi driver.
(Last tested against a slightly earlier version of that driver.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch fixes some dyntick locking issues on ARM as pointed
out by Russell King.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Move the printk of the CPU information and IDCODE
before the checking of the table entry validity
to aide in debugging new cpu entries.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Using the low-level debug routines early in the
kernel debug cause the 1:1 mapping to get into
the TLB, which is not flushed until after the
CPU detection process (which needs the GPIO VA).
This patch moves the VA for the GPIO to the
same offset as the physical offset of the UART
to the GPIO.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
If CONFIG_CPU_DCACHE_WRITETHOUGH is set, then the
S3C24XX PM code fails to compile, as there is no
need to flush the D-cache, the flush function
arm920_flush_kern_cache_all() is not compiled.
Fix the code to not use this if the config is set.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The default serial port-mapping for the Osiris has
the port 2 mapped onto the first serial port, and
no port1. Correct this so port 1 is port.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
This code was still using the old format for the ARMv6 CPU id and it wasn't
flushing the caches on the MPCore CPU (and other ARM1176 cores). The patch
changes the mask bits to cope with the new id format.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Paul Brook
The old-abi sys_syscall syscall is broken when called from Thumb mode. It
assumes the syscall number is an Arm syscall number (ie. starts from
__NR_OABI_SYSCALL_BASE). In thumb mode syscall numbers start from zero.
The patch below fixes this by clearing the nigh bits of the syscall number
instead of inverting them. Technically this means we accept some invalid
syscall numbers, but I can't see how that could be a problem. The two sets of
numbers far apart that unimplemented syscalls should still be rejected.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vitaly Wool
This patch adds default configuration file PNX4008 ARM platform.
It\'s basically the same as the previos one.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Dmitry Pervushin <dpervushin@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vitaly Wool
This patch adds basic chip support for PNX4008 ARM platform.
It's basically the same as the previous one, but with the rmk's
comments taken into account.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Dmitry Pervushin <dpervushin@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vitaly Wool
This patch adds kernel headers for PNX4008 ARM platform.
It's basically the same as the previos one, but with the rmk's comments taken into account.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Dmitry Pervushin <dpervushin@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc Singer
New documentation for the touchscreen controllers and LCD panels.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc Singer
Reworking of the adaptation macros to allow driver to compile again
for the lpd7x's. Also, support added for the lh79520 so it may use
the smc91x.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc Singer
Driver for operating SSP devices through LPD7A40X CPLD chip. This
driver is used by the audio codecs.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc Singer
Board support and LCD panel configurations to integrate lh7a40x's with
the amba clcd driver.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc Singer
Revised default configuration files.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc Singer
The serial driver now sets up the third UART when it is to be used.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc Singer
Updates to the lpd7a40x_platform files. Includes support for new
architecture, lpd7a400.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc Singer
Updates to the lpd7a40x platform headers. Includes support for new
architecture, lpd7a400.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reflect the fact that the Cell Broadband Engine supports 64k
pages by adding the bit to the CPU features.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The page size encoding passed to tlbie is incorrect for new-style
large pages. This fixes it. This doesn't affect anything on older
machines because mmu_psize_defs[psize].penc (the page size encoding)
is 0 for 4k and 16M pages (the two are distinguished by a separate "is
a large page" bit).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arm_timer() checks PF_EXITING to prevent BUG_ON(->exit_state)
in run_posix_cpu_timers().
However, for some reason it does so only for CPUCLOCK_PERTHREAD
case (which is imho wrong).
Also, this check is not reliable, PF_EXITING could be set on
another cpu without any locks/barriers just after the check,
so it can't prevent from attaching the timer to the exiting
task.
The previous patch makes this check unneeded.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
do_exit() clears ->it_##clock##_expires, but nothing prevents
another cpu to attach the timer to exiting process after that.
arm_timer() tries to protect against this race, but the check
is racy.
After exit_notify() does 'write_unlock_irq(&tasklist_lock)' and
before do_exit() calls 'schedule() local timer interrupt can find
tsk->exit_state != 0. If that state was EXIT_DEAD (or another cpu
does sys_wait4) interrupted task has ->signal == NULL.
At this moment exiting task has no pending cpu timers, they were
cleanuped in __exit_signal()->posix_cpu_timers_exit{,_group}(),
so we can just return from irq.
John Stultz recently confirmed this bug, see
http://marc.theaimsgroup.com/?l=linux-kernel&m=115015841413687
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the local timer interrupt happens just after do_exit() sets PF_EXITING
(and before it clears ->it_xxx_expires) run_posix_cpu_timers() will call
check_process_timers() with tasklist_lock + ->siglock held and
check_process_timers:
t = tsk;
do {
....
do {
t = next_thread(t);
} while (unlikely(t->flags & PF_EXITING));
} while (t != tsk);
the outer loop will never stop.
Actually, the window is bigger. Another process can attach the timer
after ->it_xxx_expires was cleared (see the next commit) and the 'if
(PF_EXITING)' check in arm_timer() is racy (see the one after that).
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A couple of fixes that should prevent crashes when using netconsole and
suspend/resume. First, netconsole poll routine shouldn't run unless the
device is up; second, the NAPI poll should be disabled during suspend.
This is only an issue on sky2, because it has to have one NAPI poll
routine for both ports on dual port boards. Normal drivers use
netif_rx_schedule_prep and that checks for netif_running.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If get_user_pages() returns less pages than what we asked for, we jump
to out_unmap which will return ERR_PTR(ret). But ret can contain a
positive number just smaller than local_nr_pages, so be sure to set it
to -EFAULT always.
Problem found and diagnosed by Damien Le Moal <damien@sdl.hitachi.co.jp>
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some time ago the cdrom open routine was changed so that we call the
driver's open routine before checking to see if it is read only. However,
if we discovered that a read write open was not possible and the open
flags required a writable open, we just returned -EROFS without calling
the driver's release routine. This seems to work for most cdrom drivers,
but breaks the Powerpc iSeries virtual cdrom rather badly.
This just inserts the release call in the error path to balance the call
to "->open()" done by "open_for_data()".
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We don't clear the seek stat values in cfq_alloc_io_context(), and if
->seek_mean is unlucky enough to be set to -36 by chance, the first
invocation of cfq_update_io_seektime() will oops with a divide by zero
in do_div().
Just memset the entire cic instead of filling invididual values
independently.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If flock_lock_file() failed to allocate flock with locks_alloc_lock()
then "error = 0" is returned. Need to return some non-zero.
Signed-off-by: Pavel Emelianov <xemul@openvz.org>
Signed-off-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The resume bug was caused not by an early interrupt but because the idle
timeout was not being stopped on suspend. Also disable hardware IRQ's
on suspend. Will need to revisit this with hotplug?
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
