Because the value of CONFIG_SERIAL_SH_SCI_NR_UARTS is 3.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All 1st cut silicon in the wild has been replaced by the 2nd cut, so it's
safe to replace all of the 1st cut references and support.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Newer parts need NR_IRQS > 256, so simply bump this up to 512 across the
board. At this point sparseirq is used unconditionally across all CPUs,
so this introduces minimal overhead.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When CONFIG_PMB enable, ITLB is not cleared by reset of watchdog timer.
This should use trigger_address_error().
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This provides a sledgehammer approach for clearing the TLBs, only to be
used in cases where we know we will never want to use the mappings again
and have no interest in preserving state. This also destroys wired
entries.
The primary use for this is when we are either entering or exiting the
kernel completely, in the latter case as a precursor for CPU reset by
MMU.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This typo seems to have been copy and pasted in the PCI initialization
code. Replace 'intialization' with 'initialization'.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
page_table_range_init() presently allocates a PUD page for the 3-level
page table case on X2 TLB configurations on each successive call. This
results in the previous PUD page being trampled when PMDs with an
overlapping PUD are initialized. This case was triggered by putting
persistent kmaps immediately below the fixmap range for highmem.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There was an off-by-1 in the begin/end of the ioremap fixmaps, leaving us
with a spurious entry. In practice this wasn't a problem since we aligned
on a PMD boundary anyways, but this makes it consistent with the
intention and the other fixmaps.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch series adds support for ITO Co., Ltd.'s SH-2007 reference
platform (A PC-104 based SH7780 platform).
This is a direct port of the out-of-tree board support from the vendor's
kernel, originally located at:
http://ms-n.org/sh-linux/kernel/
More information on the board and the vendor can be obtained from the
vendor's site at:
http://www.itonet.co.jp/
Presently supported peripherals are CF and ethernet, with support for
the on-board IDE still pending further testing.
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Hitoshi Mitake <mitake@dcl.info.waseda.ac.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The function begins and ends with a read_lock. The latter is changed to a
read_unlock.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@locked@
expression E1;
position p;
@@
read_lock(E1@p,...);
@r exists@
expression x <= locked.E1;
expression locked.E1;
expression E2;
identifier lock;
position locked.p,p1,p2;
@@
*lock@p1 (E1@p,...);
... when != E1
when != \(x = E2\|&x\)
*lock@p2 (E1,...);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the FDPIC relocations have been given fixed numbers upstream,
switch to using those. The previous values only applied to experimental
toolchains that never made it in to the wild, so the impact remains
minimal.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently kprobes support relies on several saved opcode variables for
saving and restoring state, without any specific locking. This is
inherently racy on SMP, and given that we already use per-CPU variables
for everything else, convert these over too.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
asm/ptrace.h is getting a bit messy, with the _32/_64-specific changes
being fairly insular. This splits out the header accordingly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the x86/ppc changes for kprobe-based event tracing on sh.
While kprobes is only supported on 32-bit sh, we provide the API for
HAVE_REGS_AND_STACK_ACCESS_API for both 32 and 64-bit.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Since now all modification to event->count (and ->prev_count
and ->period_left) are local to a cpu, change then to local64_t so we
avoid the LOCK'ed ops.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On 64bit, local_t is of size long, and thus we make local64_t an alias.
On 32bit, we fall back to atomic64_t. (architecture can provide optimized
32-bit version)
(This new facility is to be used by perf events optimizations.)
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: linux-arch@vger.kernel.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
pcibios_fixup_device_resources() presently skips over resources flagged
with IORESOURCE_PCI_FIXED, which is a remnant of the old PCI-auto code.
The only user for this at present is the Dreamast GAPSPCI code which
can't tolerate any adjustments to the BARs, but a combination of the
IORESOURCE_PCI_FIXED and zeroed out hose offsets does the right thing for
this case already, so we simply kill off the special casing.
Reported-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (23 commits)
sh: Make intc messages consistent via pr_fmt.
sh: make sure static declaration on ms7724se
sh: make sure static declaration on mach-migor
sh: make sure static declaration on mach-ecovec24
sh: make sure static declaration on mach-ap325rxa
clocksource: sh_cmt: compute mult and shift before registration
clocksource: sh_tmu: compute mult and shift before registration
sh: PIO disabling for x3proto and urquell.
sh: mach-sdk7786: conditionally disable PIO support.
sh: support for platforms without PIO.
usb: r8a66597-hcd pio to mmio accessor conversion.
usb: gadget: r8a66597-udc pio to mmio accessor conversion.
usb: gadget: m66592-udc pio to mmio accessor conversion.
sh: add romImage MMCIF boot for sh7724 and Ecovec V2
sh: add boot code to MMCIF driver header
sh: prepare MMCIF driver header file
sh: allow romImage data between head.S and the zero page
sh: Add support MMCIF for ecovec
sh: remove duplicated #include
input: serio: disable i8042 for non-cayman sh platforms.
...
urquell only provides PIO in the PCI case, while the x3proto board never
had a working PCIe controller, so it can simply disable it outright.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This extends some of the existing special casing for HAS_IOPORT
platforms and gets it to the point where platforms can begin to
conditionally select it.
The major changes here are that the PIO routines themselves go away
completely, including all of the machvec port mapping wrappers. With this
in place it's possible for any non-machvec abusing platform to disable
PIO completely. At present this is left as an opt-in until the abusers
are the odd ones out instead of the majority.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'for-35' of git://repo.or.cz/linux-kbuild: (81 commits)
kbuild: Revert part of e8d400a to resolve a conflict
kbuild: Fix checking of scm-identifier variable
gconfig: add support to show hidden options that have prompts
menuconfig: add support to show hidden options which have prompts
gconfig: remove show_debug option
gconfig: remove dbg_print_ptype() and dbg_print_stype()
kconfig: fix zconfdump()
kconfig: some small fixes
add random binaries to .gitignore
kbuild: Include gen_initramfs_list.sh and the file list in the .d file
kconfig: recalc symbol value before showing search results
.gitignore: ignore *.lzo files
headerdep: perlcritic warning
scripts/Makefile.lib: Align the output of LZO
kbuild: Generate modules.builtin in make modules_install
Revert "kbuild: specify absolute paths for cscope"
kbuild: Do not unnecessarily regenerate modules.builtin
headers_install: use local file handles
headers_check: fix perl warnings
export_report: fix perl warnings
...
This patch is V2 of the MMCIF romImage boot support
for sh7724 and the Ecovec board. With this patch
applied and CONFIG_ROMIMAGE_MMCIF selected the
romImage kernel image can be written to a MMC card
and booted directly by the sh7724 cpu.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Extend the romImage code to allow putting data between
the head.S file and the empty_zero_page. Needed in the
case of more advanced loader code in a separate C file.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds MMCIF platform data for the Ecovec board.
Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There are only two ways to define sg_dma_len(); use sg->dma_length or
sg->length. This patch introduces NEED_SG_DMA_LENGTH that enables
architectures to choose sg->dma_length or sg->length.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Blackfin/FRV/SuperH guys all have the same exact FDPIC ptrace code in
their arch handlers (since they were probably copied & pasted). Since
these ptrace interfaces are an arch independent aspect of the FDPIC code,
unify them in the common ptrace code so new FDPIC ports don't need to copy
and paste this fundamental stuff yet again.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Roland McGrath <roland@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit b3b77c8cae, which was
also totally broken (see commit 0d2daf5cc8 that reverted the crc32
version of it). As reported by Stephen Rothwell, it causes problems on
big-endian machines:
> In file included from fs/jfs/jfs_types.h:33,
> from fs/jfs/jfs_incore.h:26,
> from fs/jfs/file.c:22:
> fs/jfs/endian24.h:36:101: warning: "__LITTLE_ENDIAN" is not defined
The kernel has never had that crazy "__BYTE_ORDER == __LITTLE_ENDIAN"
model. It's not how we do things, and it isn't how we _should_ do
things. So don't go there.
Requested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linux does not define __BYTE_ORDER in its endian header files which makes
some header files bend backwards to get at the current endian. Lets
#define __BYTE_ORDER in big_endian.h/litte_endian.h to make it easier for
header files that are used in user space too.
In userspace the convention is that
1. _both_ __LITTLE_ENDIAN and __BIG_ENDIAN are defined,
2. you have to test for e.g. __BYTE_ORDER == __BIG_ENDIAN.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The dwarf unwinder ties in to an early initcall, but it's possible that
return_address() calls will be made prior to that. This implements some
additional error handling in to the dwarf unwinder as well as an exit
path in the return_address() case to bail out if the unwinder hasn't come
up yet.
This fixes a NULL pointer deref in early boot when mempool_alloc() blows
up on the not-yet-ready mempool via dwarf_unwind_stack().
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The build scripts inadvertently dropped this down to 29-bit, fix it
back up.
Reported-by: Raul Porcel <armin76@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
kfr2r09 board has a micro-SD card slot, therefore card write-protection
detection cannot work there, disable it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a list of SCIF and SDHI DMA slave definitions to sh7724.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SuperH SDHI controllers can use DMA, add slave definitions to sh7722.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that DMA slave IDs are only used used in platform specific code and have
become opaque cookies for the rest of the code, we can make the, CPU specific
too.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Ecovec uses the AK8813 video envoder similarly to the ms7724se platform with
the only difference, that on ecovec GPIOs are used for resetting and powering
up and down the chip.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.infradead.org/iommu-2.6:
intel-iommu: Set a more specific taint flag for invalid BIOS DMAR tables
intel-iommu: Combine the BIOS DMAR table warning messages
panic: Add taint flag TAINT_FIRMWARE_WORKAROUND ('I')
panic: Allow warnings to set different taint flags
intel-iommu: intel_iommu_map_range failed at very end of address space
intel-iommu: errors with smaller iommu widths
intel-iommu: Fix boot inside 64bit virtualbox with io-apic disabled
intel-iommu: use physfn to search drhd for VF
intel-iommu: Print out iommu seq_id
intel-iommu: Don't complain that ACPI_DMAR_SCOPE_TYPE_IOAPIC is not supported
intel-iommu: Avoid global flushes with caching mode.
intel-iommu: Use correct domain ID when caching mode is enabled
intel-iommu mistakenly uses offset_pfn when caching mode is enabled
intel-iommu: use for_each_set_bit()
intel-iommu: Fix section mismatch dmar_ir_support() uses dmar_tbl.
Implement kgdb_arch_pc() which adjusts the pc if it needs to be
adjusted after a software breakpoint trap.
Implement kgdb_arch_set_pc() which is a new required function in the
kgdb debug core.
When processing a single step return zero in the error exception field
so that the debug core can distinguish between a single step trap and
a breakpoint trap generically.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (44 commits)
vlynq: make whole Kconfig-menu dependant on architecture
add descriptive comment for TIF_MEMDIE task flag declaration.
EEPROM: max6875: Header file cleanup
EEPROM: 93cx6: Header file cleanup
EEPROM: Header file cleanup
agp: use NULL instead of 0 when pointer is needed
rtc-v3020: make bitfield unsigned
PCI: make bitfield unsigned
jbd2: use NULL instead of 0 when pointer is needed
cciss: fix shadows sparse warning
doc: inode uses a mutex instead of a semaphore.
uml: i386: Avoid redefinition of NR_syscalls
fix "seperate" typos in comments
cocbalt_lcdfb: correct sections
doc: Change urls for sparse
Powerpc: wii: Fix typo in comment
i2o: cleanup some exit paths
Documentation/: it's -> its where appropriate
UML: Fix compiler warning due to missing task_struct declaration
UML: add kernel.h include to signal.c
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (127 commits)
sh: update defconfigs.
sh: Fix up the NUMA build for recent LMB changes.
sh64: provide a stub per_cpu_trap_init() definition.
sh: fix up CONFIG_KEXEC=n build.
sh: fixup the docbook paths for clock framework shuffling.
driver core: Early dev_name() depends on slab_is_available().
sh: simplify WARN usage in SH clock driver
sh: Check return value of clk_get on ms7724
sh: Check return value of clk_get on ecovec24
sh: move sh clock-cpg.c contents to drivers/sh/clk-cpg.c
sh: move sh clock.c contents to drivers/sh/clk.
sh: move sh asm/clock.h contents to linux/sh_clk.h V2
sh: remove unused clock lookup
sh: switch boards to clkdev
sh: switch sh4-202 to clkdev
sh: switch shx3 to clkdev
sh: switch sh7757 to clkdev
sh: switch sh7763 to clkdev
sh: switch sh7780 to clkdev
sh: switch sh7786 to clkdev
...
WARN() is used in some places to report firmware or hardware bugs that
are then worked-around. These bugs do not affect the stability of the
kernel and should not set the flag for TAINT_WARN. To allow for this,
add WARN_TAINT() and WARN_TAINT_ONCE() macros that take a taint number
as argument.
Architectures that implement warnings using trap instructions instead
of calls to warn_slowpath_*() now implement __WARN_TAINT(taint)
instead of __WARN().
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Helge Deller <deller@gmx.de>
Tested-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (311 commits)
perf tools: Add mode to build without newt support
perf symbols: symbol inconsistency message should be done only at verbose=1
perf tui: Add explicit -lslang option
perf options: Type check all the remaining OPT_ variants
perf options: Type check OPT_BOOLEAN and fix the offenders
perf options: Check v type in OPT_U?INTEGER
perf options: Introduce OPT_UINTEGER
perf tui: Add workaround for slang < 2.1.4
perf record: Fix bug mismatch with -c option definition
perf options: Introduce OPT_U64
perf tui: Add help window to show key associations
perf tui: Make <- exit menus too
perf newt: Add single key shortcuts for zoom into DSO and threads
perf newt: Exit browser unconditionally when CTRL+C, q or Q is pressed
perf newt: Fix the 'A'/'a' shortcut for annotate
perf newt: Make <- exit the ui_browser
x86, perf: P4 PMU - fix counters management logic
perf newt: Make <- zoom out filters
perf report: Report number of events, not samples
perf hist: Clarify events_stats fields usage
...
Fix up trivial conflicts in kernel/fork.c and tools/perf/builtin-record.c
Now that the node 0 initialization code has been overhauled, kill off the
now obsolete setup_memory() bits.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is needed to fix up the build at the moment. Gradually this will be
reworked to follow the 32-bit initialization path and deal with delayed
VBR initialization.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The reserve_crashkernel() definition is in asm/kexec.h which is only
dragged in via linux/kexec.h if CONFIG_KEXEC is set. Just switch over to
asm/kexec.h unconditionally to fix up the build.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
In preparation for removing volatile from the atomic_t definition, this
patch adds a volatile cast to all the atomic read functions.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the CPG helpers to drivers/sh/clk-cpg.c V2.
This to allow SH-Mobile ARM to share the code with
SH. All functions except the legacy CPG stuff is moved.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is V2 of the SH clock framework move from
arch/sh/kernel/cpu/clock.c to drivers/sh/clk.c. All
code except the following functions are moved:
clk_init(), clk_get() and clk_put().
The init function is still kept in clock.c since it
depends on the SH-specific machvec implementation.
The symbols clk_get() and clk_put() already exist in
the common ARM clkdev code, those symbols are left in
the SH tree to avoid duplicating them for SH-Mobile ARM.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is V2 of the clock framework move from
arch/sh/include/asm/clock.h to include/linux/sh_clk.h
and updates the include paths for files that will be
shared between SH and SH-Mobile ARM.
The file asm/clock.h is still kept in this version,
this to depend on as few files as possible at this
point. We keep SH specific stuff in there.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now when all clocks are registered using clkdev,
get rid of the special SH-specific clock lookup.
Also ditch the unused module ref counting code.
This patch syncs the SH behaviour with ARM.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the remaining board clocks
to use clkdev for lookup if needed. The unused
name and id from struct clk are also removed.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the remaining sh4-202 clocks
to use clkdev for lookup. The now unused name
and id from struct clk are also removed.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the remaining shx3 clocks
to use clkdev for lookup. The now unused name
and id from struct clk are also removed.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the remaining sh7757 clocks
to use clkdev for lookup. The now unused name
and id from struct clk are also removed.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the remaining sh7763 clocks
to use clkdev for lookup. The now unused name
and id from struct clk are also removed.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the remaining sh7780 clocks
to use clkdev for lookup. The now unused name
and id from struct clk are also removed.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the remaining sh7786 clocks
to use clkdev for lookup. The now unused name
and id from struct clk are also removed.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the remaining sh7785 clocks
to use clkdev for lookup. The now unused name
and id from struct clk are also removed.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the remaining sh7366 clocks
to use clkdev for lookup. The now unused name
and id from struct clk are also removed.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the remaining sh7343 clocks
to use clkdev for lookup. The now unused name
and id from struct clk are also removed.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the remaining sh7722 clocks
to use clkdev for lookup. The now unused name
and id from struct clk are also removed.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the remaining sh7723 clocks
to use clkdev for lookup. The now unused name
and id from struct clk are also removed.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the remaining sh7724 clocks
to use clkdev for lookup. The now unused name
and id from struct clk are also removed.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the legacy clocks to register
using clkdev. Also the clock name is removed.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove the name parameter from SH_CLK_DIV4() and
adjust the processor specific code. The lookup
happens using clkdev so the name is unused.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the div4 set_parent() callback to use the
flags instead of name to determine parent index.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove the name and the id from SH_CLK_MSTP32().
Now when lookups are handled by clkdev they are
not needed anymore.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds sh7786 MSTP enums for mstp_clks[] index.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds sh7785 MSTP enums for mstp_clks[] index.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds sh7366 MSTP enums for mstp_clks[] index.
The MSTP bit for the SIU is removed as well since it is
not included in the documentation. Most likely an old
copy paste error from sh7722.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds sh7343 MSTP enums for mstp_clks[] index.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
In the NUMA or memory hot-add case where system memory has been
partitioned up, we immediately run in to a situation where the existing
PMB entry doesn't cover the new range (primarily as a result of the entry
size being shrunk to match the node size early in the initialization). In
order to fix this up it's necessary to preload a PMB mapping for the new
range prior to activation in order to circumvent reset by MMU.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The minimum section size for the PMB is 16M, so just always error
out early if the specified size is too small. This permits us to
unconditionally call in to pmb_bolt_mapping() with variable sizes
without wasting a TLB and cache flush for the range.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This reworks much of the bootmem setup and initialization code allowing
us to get rid of duplicate work between the NUMA and non-NUMA cases. The
end result is that we end up with a much more flexible interface for
supporting more complex topologies (fake NUMA, highmem, etc, etc.) which
is entirely LMB backed. This is an incremental step for more NUMA work as
well as gradually enabling migration off of bootmem entirely.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Rewinding each debugfs entries to unregister if an error happens.
Based on the commit ca4caa4e1d
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Get rid of div6 clock names on
sh7343/sh7366/sh7722/sh7723/sh7724
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use clkdev for div6 lookup on SH-Mobile processors:
sh7343/sh7366/sh7722/sh7723/sh7724
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove the clock name from sh7722/sh7723/sh7724
hwblk clocks. Lookup is handled by clkdev.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Modify the SuperH clock code to support struct clk
with NULL as name. Such clocks will not be hooked
up to debugfs.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use clkdev for lookup of hwblk clocks on
sh7722/sh7723/sh7724.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Modify sh7722/sh7723/sh7724 to use clkdev for
TMU and SCIF clock lookups.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Rework the sh7722/sh7723/sh7724 hwblk code to use the
hwblk id as index in the mstp clock array.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This reworks the memory limit handling to tie in through the available
LMB infrastructure. This requires a bit of reordering as we need to have
all of the LMB reservations taken care of prior to establishing the
limits.
While we're at it, the crash kernel reservation semantics are reworked
so that we allocate from the bottom up and reduce the risk of having
to disable the memory limit due to a clash with the crash kernel
reservation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This plugs in a memory init callback in the machvec to permit boards to
wire up various bits of memory directly in to LMB. A generic machvec
implementation is provided that simply wraps around the normal
Kconfig-derived memory start/size.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The elfcorehdr parsing was just tossed in setup.c, but nothing outside of
the crash dump code/vmcore bits require it, so we just move it out of the
way, as per ppc.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There's still quite a bit of shootdown logic that needs to be hacked up
to support SMP for kdump properly, so just add in a BROKEN_ON_SMP
dependency for now.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This bumps up the extra LMB reservations in ordering so that they're
accounted for prior to iterating over the region list. This ensures that
reservations are visible both within the LMB and bootmem context.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Various boot loaders go to various extents to thwart the initrd detection
logic (mostly on account of not being able to be bothered with adhering
to the established boot ABI), so we make the detection logic a bit more
robust. This makes it possible to work around the SDK7786's firmware's
attempts to thwart compressed image booting. Victory is mine.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The breakpoint generic layer assumes that archs always know in advance
the static number of address registers available to host breakpoints
through the HBP_NUM macro.
However this is not true for every archs. For example Arm needs to get
this information dynamically to handle the compatiblity between
different versions.
To solve this, this patch proposes to drop the static HBP_NUM macro
and let the arch provide the number of available slots through a
new hw_breakpoint_slots() function. For archs that have
CONFIG_HAVE_MIXED_BREAKPOINTS_REGS selected, it will be called once
as the number of registers fits for instruction and data breakpoints
together.
For the others it will be called first to get the number of
instruction breakpoint registers and another time to get the
data breakpoint registers, the targeted type is given as a
parameter of hw_breakpoint_slots().
Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Cc: K. Prasad <prasad@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
There are two outstanding fashions for archs to implement hardware
breakpoints.
The first is to separate breakpoint address pattern definition
space between data and instruction breakpoints. We then have
typically distinct instruction address breakpoint registers
and data address breakpoint registers, delivered with
separate control registers for data and instruction breakpoints
as well. This is the case of PowerPc and ARM for example.
The second consists in having merged breakpoint address space
definition between data and instruction breakpoint. Address
registers can host either instruction or data address and
the access mode for the breakpoint is defined in a control
register. This is the case of x86 and Super H.
This patch adds a new CONFIG_HAVE_MIXED_BREAKPOINTS_REGS config
that archs can select if they belong to the second case. Those
will have their slot allocation merged for instructions and
data breakpoints.
The others will have a separate slot tracking between data and
instruction breakpoints.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Cc: K. Prasad <prasad@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@elte.hu>
The current policies of breakpoints in x86 and SH are the following:
- task bound breakpoints can only break on userspace addresses
- cpu wide breakpoints can only break on kernel addresses
The former rule prevents ptrace breakpoints to be set to trigger on
kernel addresses, which is good. But as a side effect, we can't
breakpoint on kernel addresses for task bound breakpoints.
The latter rule simply makes no sense, there is no reason why we
can't set breakpoints on userspace while performing cpu bound
profiles.
We want the following new policies:
- task bound breakpoint can set userspace address breakpoints, with
no particular privilege required.
- task bound breakpoints can set kernelspace address breakpoints but
must be privileged to do that.
- cpu bound breakpoints can do what they want as they are privileged
already.
To implement these new policies, this patch checks if we are dealing
with a kernel address breakpoint, if so and if the exclude_kernel
parameter is set, we tell the user that the breakpoint is invalid,
which makes a good generic ptrace protection.
If we don't have exclude_kernel, ensure the user has the right
privileges as kernel breakpoints are quite sensitive (risk of
trap recursion attacks and global performance impacts).
[ Paul Mundt: keep addr space check for sh signal delivery and fix
double function declaration]
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Cc: K. Prasad <prasad@linux.vnet.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Tag ptrace breakpoints with the exclude_kernel attribute set. This
will make it easier to set generic policies on breakpoints, when it
comes to ensure nobody unpriviliged try to breakpoint on the kernel.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Cc: K. Prasad <prasad@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@elte.hu>
arch/sh/kernel/smp.c:164: error: conflicting types for 'native_cpu_disable'
/home/matt/src/kernels/sh-2.6/arch/sh/include/asm/smp.h:48: error: previous declaration of 'native_cpu_disable' was here
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add CONFIG_VIRTUALIZATION to the SH architecture
and include the virtio code there. Used to enable
the virtio drivers under QEMU.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The UP dependency was inherited from ARM, which seems to have run in to
it due to the stacktrace code not being available for SMP in certain
cases, as we don't have this particular limitation there is no specific
need to block on the SMP dependency.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This wires up CPU hotplug for SH-X3 SMP CPUs. Presently only secondary
cores can be hotplugged given that the boot CPU has to contend with the
broadcast timer. When real local timers are implemented this restriction
can be lifted.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This provides a cache of the secondary CPUs idle loop for the cases where
hotplug simply enters a low power state instead of resetting or powering
off the core.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
smp_store_cpu_info() is presently flagged as __init, but is called by
start_secondary() which is __cpuinit, fix it up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This iterates over the maximum number of CPUs we plan to support and
makes sure they're all set in the present CPU map.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This converts from cpu_set() for the online map to set_cpu_online().
The two online map modifiers were the last remaining manual map
manipulation bits, with this in place everything now goes through
cpumask.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the platform ops migration, the definitions still need to be
included in the CONFIG_SMP=n case, so make the asm/smp.h include
explicit.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When registering CPUs in the topology initialization ensure that all of
the present CPUs are flagged as hotpluggable.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that compressed image loading is possible for sdk7786, drop the
vmlinux.bin default image target and update the defconfig accordingly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the sh7751 pci code to handle io ports
correctly. The code is based on the sh7788x implementation.
Tested on a R2D-1 board with CONFIG_8139TOO_PIO=y.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the R2D defconfigs to bump up the maximum
number of SCIF ports on the system.
Fixes a broken serial console regression added
by cd5f107628.
Reported-by: Shin-ichiro KAWASAKI <kawasaki@juno.dti.ne.jp>
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Alexandre Courbot <alex@dcl.info.waseda.ac.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
CHCR_TS_HIGH_SHIFT is defined as a shift of TS high bits in CHCR register,
relative to low bits. The TS_INDEX2VAL() macro has to take this into account.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/mfleming/sh-2.6:
sh: Use correct mask when comparing PMB DATA array values
sh: Do not try merging two 128MB PMB mappings
sh: Fix zImage load address when CONFIG_32BIT=y
sh: Fix address to decompress at when CONFIG_32BIT=y
sh: Assembly friendly __pa and __va definitions
Lists of DMA channels and slaves are not changed, make them constant. Besides,
SH7724 channel and slave configuration of both DMA controllers is identical,
remove the extra copy of the configuration data.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
As explained in commit 1c0fe6e3bd, we want to call the architecture independent
oom killer when getting an unexplained OOM from handle_mm_fault, rather than
simply killing current.
Cc: linux-sh@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Previously we were masking the PMB DATA array values with the value of
__MEMORY_START | PMB_V, which misses some PFN bits off the mask.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
There is a logic error in pmb_merge() that means we will incorrectly try
to merge two 128MB PMB mappings into one mapping. However, 256MB isn't a
valid PMB map size and pmb_merge() will actually drop the second 128MB
mapping.
This patch allows my SDK7786 board to boot when configured with
CONFIG_MEMORY_SIZE=0x10000000.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
We can't necessarily use the P1SEG region to access RAM when running in
32BIT mode, so use CONFIG_MEMORY_START as the base address.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
When running in 32BIT mode the P1SEG region doesn't necessarily provide
a window onto RAM (it depends how the bootloader setup the PMB). The
correct location to place the decompressed kernel is the physical
address of _text.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
This patch defines ___pa and ___va which return the physical and virtual
address of an address, respectively. These macros are suitable for
calling from assembly because they don't include the C casts required by
__pa and __va.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
This cribs the MIPS plat_smp_ops approach for wrapping up the platform
ops. This will allow for mixing and matching different ops on the same
platform in the future.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This does a detect_cpu_and_cache_system() -> cpu_probe() rename, tidies
up the unused return value, and stuffs it under __cpuinit in preparation
for CPU hotplug.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the x86 change and kills off the unthrottle stub. As the x86
change killed off the generic callback it isn't used anymore anyways.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This zeroes out the number of cache aliases in the cache info descriptors
when hardware alias avoidance is enabled. This cuts down on the amount of
flushing taken care of by common code, and also permits coherency control
to be disabled for the single CPU and 4k page size case.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Previously the struct module definition was pulled in from other headers,
but we want the reference to be explicit. Fixes up randconfig build
issues.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This enables support for the hardware synonym avoidance handling on SH-X3
CPUs for the case where dcache aliases are possible. icache handling is
retained, but we flip on broadcasting of the block invalidations due to
the lack of coherency otherwise on SMP.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements support for hardware-managed IRQ balancing as implemented
by SH-X3 cores (presently only hooked up for SH7786, but can probably be
carried over to other SH-X3 cores, too).
CPUs need to specify their distribution register along with the mask
definitions, as these follow the same format. Peripheral IRQs that don't
opt out of balancing will be automatically distributed at the whim of the
hardware block, while each CPU needs to verify whether it is handling the
IRQ or not, especially before clearing the mask.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Make sure that the timer IRQs and IPIs aren't enabled for IRQ balancing.
IPIs are disabled as a result of being percpu while the timers simply
disable balancing outright.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for hardware-assisted userspace irq masking for
special priority levels. Due to the SR.IMASK interactivity, only some
platforms implement this in hardware (including but not limited to
SH-4A interrupt controllers, and ARM-based SH-Mobile CPUs). Each CPU
needs to wire this up on its own, for now only SH7786 is wired up as an
example.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently address translation is default-enabled regardless of whether
CONFIG_MMU is set or not in the SH-4 case, this fixes it up, and also
makes the control init word a bit more readable in the process.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
While the MMUCR.URB and ITLB/UTLB differentiation works fine for all SH-4
and later TLBs, these features are absent on SH-3. This splits out
local_flush_tlb_all() in to SH-4 and PTEAEX copies while restoring the
old SH-3 one, subsequently fixing up the build.
This will probably want some further reordering and tidying in the
future, but that's out of scope at present.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Now with the lookup aliases in place there is no longer any need to
provide the clock string, kill it off for all legacy CPG CPUs.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
For the CPUs that have not yet been converted off of legacy CPG we
provide some pclk aliases in order to make driver migration easier.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This plugs in clkdev lookups for the SH7786 clocks and migrates off of
clock string usage for the TMU clocks.
Previously the TMU clocks were aliased to the peripheral clock, so this
gets the driver actually toggling the proper clocks now as well.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Export the status of the utlb and itlb entries through debugfs.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
For the boot, enable_mmu() is called from setup_arch() but we don't call
setup_arch() for any of the other cpus. So turn on the non-boot cpu's
mmu inside of start_secondary().
I noticed this bug on an SMP board when trying to map I/O memory
(smsc911x registers) into the kernel address space. Since the Address
Translation bit in MMUCR wasn't set, accessing the virtual address where
the smsc911x registers were supposedly mapped actually performed a
physical address access.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Cc: stable@kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Ensure that the aux table is properly initialized, even when optional
features are missing. Without this, the FDPIC loader did not work.
Signed-off-by: Andrew Stubbs <ams@codesourcery.com>
Cc: stable@kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use set_cpus_allowed_ptr rather than set_cpus_allowed.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E1,E2;
@@
- set_cpus_allowed(E1, cpumask_of_cpu(E2))
+ set_cpus_allowed_ptr(E1, cpumask_of(E2))
@@
expression E;
identifier I;
@@
- set_cpus_allowed(E, I)
+ set_cpus_allowed_ptr(E, &I)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently the TLB wiring code depends on MMUCR.URB for working out where
to place the wired entry, but fails to take the replacment counter in to
consideration. This fixes up the wiring logic and ensures that wired
entries remain so.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Create a common platform data header file for the
shdma dmaengine driver. This is done by moving
common structures from sh asm/dmaengine.h to
linux/sh_dma.h. DMA registers are also copied from
sh asm/dma-register.h to make the code architecture
independent.
The sh header file asm/dmaengine.h is still kept
with the slave id enum. This allows us to keep the
old processor specific code as is and slowly move
over to slave id enums in per-processor headers.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Move SHDMA_SLAVE_NUMBER from asm/dmaengine.h to
shdma.h. Set it to 256 to support a wide range
of processors. The amount of memory consumed by
this change is limited to 256 bits.
While at it, rename to SH_DMA_SLAVE_NUMBER to
match with the rest of the file.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch replaces the sh_dmae_slave_chan_id enum
with an unsigned int. The purpose of this chainge is
to make it possible to separate the slave id enums
from the dmaengine header.
The slave id enums varies with processor model, so in
the future it makes sense to put these in the processor
specific headers together with the pinmux enums.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The parent rb_node needs to be initialized to shut up the compiler, even
though we're unlikely to ever hit this issue at run time.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
select_idle_routine() and register_sh_pmu() both needed their annotations
fixed up to silence section mismatch warnings.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
set_pmb_entry() is now only used by a function that is wrapped in #ifdef
CONFIG_PM, so wrap set_pmb_entry() in CONFIG_PM too.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Setting the TI in MMUCR causes all the TLB bits in MMUCR to be
cleared. Unfortunately, the TLB wired bits are also cleared when setting
the TI bit, causing any wired TLB entries to become unwired.
Use local_flush_tlb_all() which implements TLB flushing in a safer
manner by using the memory-mapped TLB registers. As each CPU has its own
PMB the modifications in pmb_init() only affect the local CPU, so only
flush the local CPU's TLB.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
flush_tlb_page() can be used to flush TLB entries that map executable
pages. Therefore, we need to ensure that the ITLB is also flushed in
local_flush_tlb_page().
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
interruptible_sleep_on() is referenced for use in the mid_sched macro
which is not used anywhere. Remove reference and macro as well as the
comment which appears to belong with them.
Signed-off-by: Andreas Bombe <aeb@debian.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
i2c_put_adapter is needed after i2c_get_adapter
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
serial: sh-sci: remove duplicated #include
sh: Export uncached helper symbols.
sh: Fix up NUMA build for 29-bit.
serial: sh-sci: Fix build failure for non-sh architectures.
sh: Fix up uncached offset for legacy 29-bit mode.
sh: Support CPU affinity masks for INTC controllers.
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (35 commits)
perf: Fix unexported generic perf_arch_fetch_caller_regs
perf record: Don't try to find buildids in a zero sized file
perf: export perf_trace_regs and perf_arch_fetch_caller_regs
perf, x86: Fix hw_perf_enable() event assignment
perf, ppc: Fix compile error due to new cpu notifiers
perf: Make the install relative to DESTDIR if specified
kprobes: Calculate the index correctly when freeing the out-of-line execution slot
perf tools: Fix sparse CPU numbering related bugs
perf_event: Fix oops triggered by cpu offline/online
perf: Drop the obsolete profile naming for trace events
perf: Take a hot regs snapshot for trace events
perf: Introduce new perf_fetch_caller_regs() for hot regs snapshot
perf/x86-64: Use frame pointer to walk on irq and process stacks
lockdep: Move lock events under lockdep recursion protection
perf report: Print the map table just after samples for which no map was found
perf report: Add multiple event support
perf session: Change perf_session post processing functions to take histogram tree
perf session: Add storage for seperating event types in report
perf session: Change add_hist_entry to take the tree root instead of session
perf record: Add ID and to recorded event data when recording multiple events
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (56 commits)
doc: fix typo in comment explaining rb_tree usage
Remove fs/ntfs/ChangeLog
doc: fix console doc typo
doc: cpuset: Update the cpuset flag file
Fix of spelling in arch/sparc/kernel/leon_kernel.c no longer needed
Remove drivers/parport/ChangeLog
Remove drivers/char/ChangeLog
doc: typo - Table 1-2 should refer to "status", not "statm"
tree-wide: fix typos "ass?o[sc]iac?te" -> "associate" in comments
No need to patch AMD-provided drivers/gpu/drm/radeon/atombios.h
devres/irq: Fix devm_irq_match comment
Remove reference to kthread_create_on_cpu
tree-wide: Assorted spelling fixes
tree-wide: fix 'lenght' typo in comments and code
drm/kms: fix spelling in error message
doc: capitalization and other minor fixes in pnp doc
devres: typo fix s/dev/devm/
Remove redundant trailing semicolons from macros
fix typo "definetly" -> "definitely" in comment
tree-wide: s/widht/width/g typo in comments
...
Fix trivial conflict in Documentation/laptops/00-INDEX
All the architectures properly set NEED_DMA_MAP_STATE now so we can safely
add linux/pci-dma.h to linux/pci.h and remove the linux/pci-dma.h
inclusion in arch's asm/pci.h
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While in theory user_enable_single_step/user_disable_single_step/
user_enable_blockstep could also be provided as an inline or macro there's
no good reason to do so, and having the prototype in one places keeps code
size and confusion down.
Roland said:
The original thought there was that user_enable_single_step() et al
might well be only an instruction or three on a sane machine (as if we
have any of those!), and since there is only one call site inlining
would be beneficial. But I agree that there is no strong reason to care
about inlining it.
As to the arch changes, there is only one thought I'd add to the
record. It was always my thinking that for an arch where
PTRACE_SINGLESTEP does text-modifying breakpoint insertion,
user_enable_single_step() should not be provided. That is,
arch_has_single_step()=>true means that there is an arch facility with
"pure" semantics that does not have any unexpected side effects.
Inserting a breakpoint might do very unexpected strange things in
multi-threaded situations. Aside from that, it is a peculiar side
effect that user_{enable,disable}_single_step() should cause COW
de-sharing of text pages and so forth. For PTRACE_SINGLESTEP, all these
peculiarities are the status quo ante for that arch, so having
arch_ptrace() itself do those is one thing. But for building other
things in the future, it is nicer to have a uniform "pure" semantics
that arch-independent code can expect.
OTOH, all such arch issues are really up to the arch maintainer. As
of today, there is nothing but ptrace using user_enable_single_step() et
al so it's a distinction without a practical difference. If/when there
are other facilities that use user_enable_single_step() and might care,
the affected arch's can revisit the question when someone cares about
the quality of the arch support for said new facility.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add generic implementations of the old and really old uname system calls.
Note that sh only implements sys_olduname but not sys_oldolduname, but I'm
not going to bother with another ifdef for that special case.
m32r implemented an old uname but never wired it up, so kill it, too.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: James Morris <jmorris@namei.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a generic implementation of the ipc demultiplexer syscall. Except for
s390 and sparc64 all implementations of the sys_ipc are nearly identical.
There are slight differences in the types of the parameters, where mips
and powerpc as the only 64-bit architectures with sys_ipc use unsigned
long for the "third" argument as it gets casted to a pointer later, while
it traditionally is an "int" like most other paramters. frv goes even
further and uses unsigned long for all parameters execept for "ptr" which
is a pointer type everywhere. The change from int to unsigned long for
"third" and back to "int" for the others on frv should be fine due to the
in-register calling conventions for syscalls (we already had a similar
issue with the generic sys_ptrace), but I'd prefer to have the arch
maintainers looks over this in details.
Except for that h8300, m68k and m68knommu lack an impplementation of the
semtimedop sub call which this patch adds, and various architectures have
gets used - at least on i386 it seems superflous as the compat code on
x86-64 and ia64 doesn't even bother to implement it.
[akpm@linux-foundation.org: add sys_ipc to sys_ni.c]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: James Morris <jmorris@namei.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the hw_perf_event_*() hotplug hooks in favour of per PMU hotplug
notifiers. This has the advantage of reducing the static weak interface
as well as exposing all hotplug actions to the PMU.
Use this to fix x86 hotplug usage where we did things in ONLINE which
should have been done in UP_PREPARE or STARTING.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: paulus@samba.org
Cc: eranian@google.com
Cc: robert.richter@amd.com
Cc: fweisbec@gmail.com
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
LKML-Reference: <20100305154128.736225361@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This fixes up some of the I/D/F clock ambiguity in the sh-sci driver.
The interface clock in most cases just wraps back to the peripheral
clock, while the function clock wraps in to the MSTP bits. As the logic
was somewhat inverted, this cleans that up, and also enables all CPUs
with SCI MSTP bits to match function clocks through clkdev lookup.
As a result, this gets rid of the clk string abuse on the sh side, and
the clock string will be killed off once the ARM code has had a chance to
sync up. This also enables MSTP gating on CPUs like 7786 which had never
wired it up before. Impacted CPUs are primarily all SH-Mobiles, SH7785,
and SH7786.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
pmb_bolt_mapping() is undefined on 29-bit builds, so provide a stub.
This fixes up the NUMA build on platforms lacking PMB support.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that dev_name() can be used early, we no longer require a static
string. Kill off all of the superfluous timer names.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
early platform devices and the like may need to set up clock aliases,
which require an allocation at a time well before the slab allocators
are available. The clock framework comes up after bootmem, so using
bootmem as a fallback should be sufficient.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This rolls in the remainder of the clkdev API bits from the ARM tree.
This can more or less be used verbatim, so we just copy it over and nuke
our local version.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The uncached_start was being set up properly for 32-bit but managed to
break 29-bit in the process, fix it up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Constify struct sysfs_ops.
This is part of the ops structure constification
effort started by Arjan van de Ven et al.
Benefits of this constification:
* prevents modification of data that is shared
(referenced) by many other structure instances
at runtime
* detects/prevents accidental (but not intentional)
modification attempts on archs that enforce
read-only kernel data at runtime
* potentially better optimized code as the compiler
can assume that the const data cannot be changed
* the compiler/linker move const data into .rodata
and therefore exclude them from false sharing
Signed-off-by: Emese Revfy <re.emese@gmail.com>
Acked-by: David Teigland <teigland@redhat.com>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts the sh architecture to use the generic
read_persistent_clock and update_persistent_clock interfaces, reducing
the amount of arch specific code we have to maintain, and allowing for
further cleanups in the future.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
... so the "sh_debugfs_root" is already available. Previously it
wasn't and in result its path was "/sys/kernel/debug/pmb" instead of
"/sys/kernel/debug/sh/pmb".
Signed-off-by: Pawel Moll <pawel.moll@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
flush_cache_all() uses broadcast IPIs, so we can't wrap in to that when
IRQs are disabled. The local cache flush manages to do what we need here
anyways, so just switch to that.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently we run in to issues with the MMU resetting the CPU when
variable sized mappings are employed. This takes a slightly more
aggressive approach to keeping the TLB and cache state sane before
establishing the mappings in order to cut down on races observed on
SMP configurations.
At the same time, we bump the VMA range up to the 0xb000...0xc000 range,
as there still seems to be some undocumented behaviour in setting up
variable mappings in the 0xa000...0xb000 range, resulting in reset by the
TLB.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
In the case of NUMA emulation when in range PPNs are being used for
secondary nodes, we need to make sure that the PMB has a mapping for it
before setting up the pgdat. This prevents the MMU from resetting.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When entries are being bolted unconditionally it's possible that the boot
loader has established mappings that are within range that we don't want
to clobber. Perform some basic validation to ensure that the new mapping
is out of range before allowing the entry setup to take place.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This moves the pmb_remap_caller() mapping logic out in to
pmb_bolt_mapping(), which enables us to establish fixed mappings in
places such as the NUMA code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This plugs in an early_param for permitting transparent PMB-backed
ioremapping to be enabled/disabled. For the time being, we use a
default-disabled policy.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements a fairly significant overhaul of the dynamic PMB mapping
code. The primary change here is that the PMB gets its own VMA that
follows the uncached mapping and we attempt to be a bit more intelligent
with dynamic sizing, multi-entry mapping, and so forth.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch extends the .device_terminate_all() method of the shdma driver
to return number of bytes transfered in the current descriptor.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
DMA CHCR register layout is equal on sh7722 and sh7724, reuse definitions.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Separate SH DMA headers into ones, commonly used by both drivers, and ones,
specific to each of them. This will make the future development of the
dmaengine driver easier.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The shdma dmaengine driver currently uses numerous macros to support various
platforms, selected by ifdef's. Convert it to use platform device resources and
lists of channel descriptors to specify register locations, interrupt numbers
and other system-specific configuration variants. Unavoidably, we have to
simultaneously convert all shdma users to provide those resources.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Configure SIU port B pins and register the WM8978 audio codec.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is required to use the SIU ASoC driver on sh7722 systems.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
