The BCP bit in TCR4/RCR4 register rules as followings:
0 Bit clock is active high with drive outputs on rising edge
and sample inputs on falling edge.
1 Bit clock is active low with drive outputs on falling edge
and sample inputs on rising edge.
For all formats currently supported in the fsl_sai driver, they're exactly
sending data on the falling edge and sampling on the rising edge.
However, the driver clears this BCP bit for all of them which results click
noise when working with SGTL5000 and big noise with WM8962.
Thus this patch corrects the BCP settings for all the formats here to fix
the nosie issue.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Acked-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
It's quite cricial to clear error flags because SAI might hang if getting
FIFO underrun during playback (I haven't confirmed the same issue on Rx
overflow though).
So this patch enables those irq and adds isr() to clear the flags so as to
keep playback entirely safe.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch add .xlate_tdm_slot_mask support for IMX SSI, and this
will generate the TDM slot TX and RX masks.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch add .xlate_tdm_slot_mask support for ESAI, and this will
generate the TDM slot TX and RX masks.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch add fsl_asoc_xlate_tdm_slot_mask() support for utils.
For the some spcified DAI driver, this will be used to generate the
TDM slot TX/RX mask. And the TX/RX mask will use a 0 bit for an active
slot as default, and the default active bits are at the LSB of
the masks.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now that AIC23 supports two control interfaces all existing I2C users
should select I2C variant.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no point in using FIQ if DMA is available (it is selected) and
selecting FIQ currently breaks the build on non-i.MX platforms. If FIQ
is actually required the build will need to be restricted or have a
select for the relevant FIQ code adding.
Signed-off-by: Mark Brown <broonie@linaro.org>
Use table based setup to register the DAPM widgets and routes. This on one hand
makes the code a bit shorter and cleaner and on the other hand the board level
DAPM elements get registered in the card's DAPM context rather than in the
CODEC's DAPM context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: alsa-devel@alsa-project.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
o Add SND_SOC_DAIFMT_DSP_A support.
o Add SND_SOC_DAIFMT_DSP_B support.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
o Fix some bugs of fsl_sai_set_dai_fmt_tr().
o Add SND_SOC_DAIFMT_LEFT_J support.
o Add SND_SOC_DAIFMT_CBS_CFM support.
o Add SND_SOC_DAIFMT_CBM_CFS support.
o And SND_SOC_DAIFMT_RIGHT_J need to be done in the future.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Instead of jumping to the 'out' label, just return the error code immediately.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For most platforms, the CPU and ESAI device is in the same endianess
mode. While for the LS1 platform, the CPU is in LE mode and the ESAI
is in BE mode.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For most platforms, the CPU and SPDIF device is in the same endianess
mode. While for the LS1 platform, the CPU is in LE mode and the SPDIF
is in BE mode.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since the Freescale SAI, ESAI and SPDIF are using the regmap-mmio,
there needs a select of REGMAP_MMIO in the Kconfig to ensure that
regmap-mmio is actually enabled.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The commit 1abe729 (ASoC: fsl: Add missing pm to current machine
drivers) enables pm support for a few IMX machine drivers. But it does
not update dev drvdata to be the pointer to 'card'. This causes the
kernel dump below in system suspend, because snd_soc_suspend() expects
that the dev drvdata points to 'card', while it still points to the
private data of machine driver.
This patch fixes imx-sgtl5000 and imx-wm8962 by attaching 'card' to dev
drvdata and private data to card drvdata. For imx-mc13783, I simply
revert the pm change because it must be broken for the same reason and
I don't have hardware to test pm enabling code.
$ echo mem > /sys/power/state
PM: Syncing filesystems ... done.
PM: Preparing system for mem sleep
mmc1: card e624 removed
Freezing user space processes ... (elapsed 0.002 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.002 seconds) done.
PM: Entering mem sleep
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 0 PID: 1861 Comm: bash Not tainted 3.14.0-rc1+ #1648
Backtrace:
[<80012144>] (dump_backtrace) from [<800122e4>] (show_stack+0x18/0x1c)
r6:8079c77c r5:00000c5a r4:00000000 r3:00000000
[<800122cc>] (show_stack) from [<80637ac0>] (dump_stack+0x78/0x94)
[<80637a48>] (dump_stack) from [<80028918>] (warn_slowpath_common+0x6c/0x8c)
r4:bdb21c38 r3:be62df00
[<800288ac>] (warn_slowpath_common) from [<800289dc>] (warn_slowpath_fmt+0x38/0x40)
r8:be62e3a8 r7:bf122960 r6:00000005 r5:00000000 r4:00000000
[<800289a8>] (warn_slowpath_fmt) from [<8006518c>] (__lock_acquire+0x1ae0/0x1ce0)
r3:8079d598 r2:80799e70
[<800636ac>] (__lock_acquire) from [<80065894>] (lock_acquire+0x68/0x7c)
r10:bdb20000 r9:be62df00 r8:00000000 r7:00000000 r6:60000013 r5:bdb20000
r4:00000000
[<8006582c>] (lock_acquire) from [<8063c938>] (mutex_lock_nested+0x5c/0x3b8)
r7:00000000 r6:80dfc78c r5:804be444 r4:bf122928
[<8063c8dc>] (mutex_lock_nested) from [<804be444>] (snd_soc_suspend+0x34/0x42c)
r10:00000000 r9:00000000 r8:00000000 r7:bf1c4444 r6:bf1c4410 r5:be978150
r4:be978010
[<804be410>] (snd_soc_suspend) from [<8034392c>] (platform_pm_suspend+0x34/0x64)
r10:00000000 r8:00000000 r7:bf1c4444 r6:bf1c4410 r5:803438f8 r4:bf1c4410
[<803438f8>] (platform_pm_suspend) from [<80348e18>] (dpm_run_callback.isra.7+0x34/0x6c)
[<80348de4>] (dpm_run_callback.isra.7) from [<80349354>] (__device_suspend+0x10c/0x220)
r9:808dd974 r8:808c4a5c r6:00000002 r5:80e5001c r4:bf1c4410
[<80349248>] (__device_suspend) from [<8034a338>] (dpm_suspend+0x60/0x220)
r7:bf1c4410 r6:808dd90c r5:80e5001c r4:bf1c44c0
[<8034a2d8>] (dpm_suspend) from [<8034a790>] (dpm_suspend_start+0x60/0x68)
r10:8079a818 r9:00000000 r8:00000004 r7:80dfbe90 r6:80641eec r5:00000000
r4:00000002
[<8034a730>] (dpm_suspend_start) from [<8006a788>] (suspend_devices_and_enter+0x74/0x318)
r4:00000003 r3:80dfbe98
[<8006a714>] (suspend_devices_and_enter) from [<8006abd8>] (pm_suspend+0x1ac/0x244)
r10:8079a818 r8:00000004 r7:00000003 r6:80641eec r5:00000000 r4:00000003
[<8006aa2c>] (pm_suspend) from [<80069a4c>] (state_store+0x70/0xc0)
r5:00000003 r4:bd85ea40
[<800699dc>] (state_store) from [<80294034>] (kobj_attr_store+0x1c/0x28)
r10:beb9fe08 r8:00000000 r7:bdb21f78 r6:bd85ea40 r5:00000004 r4:beb9fe00
[<80294018>] (kobj_attr_store) from [<80140f90>] (sysfs_kf_write+0x54/0x58)
[<80140f3c>] (sysfs_kf_write) from [<8014474c>] (kernfs_fop_write+0xc4/0x160)
r6:bd85ea40 r5:beb9fe00 r4:00000004 r3:80140f3c
[<80144688>] (kernfs_fop_write) from [<800dfa14>] (vfs_write+0xbc/0x184)
r10:00000000 r9:00000000 r8:00000000 r7:bdb21f78 r6:00500c08 r5:00000004
r4:be782600
[<800df958>] (vfs_write) from [<800dfe00>] (SyS_write+0x48/0x70)
r10:00000000 r8:00000000 r7:00000004 r6:00500c08 r5:00000000 r4:be782600
[<800dfdb8>] (SyS_write) from [<8000e800>] (ret_fast_syscall+0x0/0x48)
r9:bdb20000 r8:8000e9c4 r7:00000004 r6:00500c08 r5:00000004 r4:76eb65e0
Fixes: 1abe729 (ASoC: fsl: Add missing pm to current machine drivers)
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The big chunks here are the updates for oxygen driver for Xonar DG
devices, which were slipped from the previous pull request. They are
device-specific and thus not too dangerous.
Other than that, all patches are small bug fixes, mainly for Samsung
build fixes, a few HD-audio enhancements, and other misc ASoC fixes.
(And this time ASoC merge is less than Octopus, lucky seven :)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=QB98
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The big chunks here are the updates for oxygen driver for Xonar DG
devices, which were slipped from the previous pull request. They are
device-specific and thus not too dangerous.
Other than that, all patches are small bug fixes, mainly for Samsung
build fixes, a few HD-audio enhancements, and other misc ASoC fixes.
(And this time ASoC merge is less than Octopus, lucky seven :)"
* tag 'sound-fix-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (42 commits)
ALSA: hda/hdmi - allow PIN_OUT to be dynamically enabled
ALSA: hda - add headset mic detect quirks for another Dell laptop
ALSA: oxygen: Xonar DG(X): cleanup and minor changes
ALSA: oxygen: Xonar DG(X): modify high-pass filter control
ALSA: oxygen: Xonar DG(X): modify input select functions
ALSA: oxygen: Xonar DG(X): modify capture volume functions
ALSA: oxygen: Xonar DG(X): use headphone volume control
ALSA: oxygen: Xonar DG(X): modify playback output select
ALSA: oxygen: Xonar DG(X): capture from I2S channel 1, not 2
ALSA: oxygen: Xonar DG(X): move the mixer code into another file
ALSA: oxygen: modify CS4245 register dumping function
ALSA: oxygen: modify adjust_dg_dac_routing function
ALSA: oxygen: Xonar DG(X): modify DAC/ADC parameters function
ALSA: oxygen: Xonar DG(X): modify initialization functions
ALSA: oxygen: Xonar DG(X): add new CS4245 SPI functions
ALSA: oxygen: additional definitions for the Xonar DG/DGX card
ALSA: oxygen: change description of the xonar_dg.c file
ALSA: oxygen: export oxygen_update_dac_routing symbol
ALSA: oxygen: add mute mask for the OXYGEN_PLAY_ROUTING register
ALSA: oxygen: modify the SPI writing function
...
Pull slave-dma updates from Vinod Koul:
- new driver for BCM2835 used in R-pi
- new driver for MOXA ART
- dma_get_any_slave_channel API for DT based systems
- minor fixes and updates spread acrooss driver
[ The fsl-ssi dual fifo mode support addition clashed badly with the
other changes to fsl-ssi that came in through the sound merge. I did
a very rough cut at fixing up the conflict, but Nicolin Chen (author
of both sides) will need to verify and check things ]
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (36 commits)
dmaengine: mmp_pdma: fix mismerge
dma: pl08x: Export pl08x_filter_id
acpi-dma: align documentation with kernel-doc format
dma: fix vchan_cookie_complete() debug print
DMA: dmatest: extend the "device" module parameter to 32 characters
drivers/dma: fix error return code
dma: omap: Set debug level to debugging messages
dmaengine: fix kernel-doc style typos for few comments
dma: tegra: add support for Tegra148/124
dma: dw: use %pad instead of casting dma_addr_t
dma: dw: join split up messages
dma: dw: fix style of multiline comment
dmaengine: k3dma: fix sparse warnings
dma: pl330: Use dma_get_slave_channel() in the of xlate callback
dma: pl330: Differentiate between submitted and issued descriptors
dmaengine: sirf: Add device_slave_caps interface
DMA: Freescale: change BWC from 256 bytes to 1024 bytes
dmaengine: Add MOXA ART DMA engine driver
dmaengine: Add DMA_PRIVATE to BCM2835 driver
dma: imx-sdma: Assign a default script number for ROM firmware cases
...
New drivers
- Samsung Maxim 14577; Micro USB, Regulator, IRQ Controller and Battery Charger
- TI/National Semiconductor LP3943 I2C GPIO Expander and PWM Generator
Existing driver adaptions
- Expansion of Wolfson Arizona DSP and High-Pass filter controls
- TI TWL6040 default Regmap support and Regcache addition/bypass
- Some nice Smatch catch fixes
- Conversion of TI OMAP-USB and TI TWL6030 to endian neutralness
- ChromeOS EC timing (delay) adaptions and added dependency on OF
- Many constifications of 'struct {mfd_cell,regmap_irq,et. al}'
- Watchdog support added for NVIDIA AS3722
- Convert functions to static in TI AM335x
- Realigned previously defeated functionality in TI AM335x
- IIO ADC-TSC concurrency dead-lock/timeout resolution
- Addition of Power Management and Clock support for Samsung core
- DEFINE_PCI_DEVICE_TABLE macro removal from MFD Subsystem
- Greater use of irqdomain functionality in ST-E AB8500
- Removal of 'include/linux/mfd/abx500/ab8500-gpio.h'
- Wolfson WM831x PMIC Power Management changes s/poweroff/shutdown/
- Device Tree documentation added for TI/Nat Semi LP3943
- Version detection and voltage tables for TI TPS6586x PMIC devices
- Simplification of Freescale MC13XXX (de-)initialisation routines
- Clean-up and simplification of the Realtek parent driver
- Added support for RTL8402 Realtek PCI-Express card reader
- Resource leak fix for Maxim 77686
- Possible suspend BUG() fix in OMAP USB TLL
- Support for new Wolfson WM5110 Revision (D)
- Testing of automatic assignment of of_node in mfd_add_device()
- Reversion of the above when it started to cause issues
- Remove legacy Platform Data from;
TI TWL Core, Qualcomm SSBI and ST-E ABx500 Pinctrl
- Clean-ups; tabbing issues, function name changes, 'drvdata = NULL' removal,
unused uninitialised warning mitigation, error message clarity,
removal of redundant/duplicate checks, licensing (GPL -> GPL2),
coding consistency, duplicate function declaration, ret checks,
commit corrections, redundant of_match_ptr() helper removal,
spelling, #if-deffery removal and header guards name changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=PuTE
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.14-1' of git://git.linaro.org/people/ljones/mfd
Pull MFD changes from Lee Jones:
"New drivers
- Samsung Maxim 14577; Micro USB, Regulator, IRQ Controller and
Battery Charger
- TI/National Semiconductor LP3943 I2C GPIO Expander and PWM
Generator
Existing driver adaptions
- Expansion of Wolfson Arizona DSP and High-Pass filter controls
- TI TWL6040 default Regmap support and Regcache addition/bypass
- Some nice Smatch catch fixes
- Conversion of TI OMAP-USB and TI TWL6030 to endian neutralness
- ChromeOS EC timing (delay) adaptions and added dependency on OF
- Many constifications of 'struct {mfd_cell,regmap_irq,et.al}'
- Watchdog support added for NVIDIA AS3722
- Convert functions to static in TI AM335x
- Realigned previously defeated functionality in TI AM335x
- IIO ADC-TSC concurrency dead-lock/timeout resolution
- Addition of Power Management and Clock support for Samsung core
- DEFINE_PCI_DEVICE_TABLE macro removal from MFD Subsystem
- Greater use of irqdomain functionality in ST-E AB8500
- Removal of 'include/linux/mfd/abx500/ab8500-gpio.h'
- Wolfson WM831x PMIC Power Management changes s/poweroff/shutdown/
- Device Tree documentation added for TI/Nat Semi LP3943
- Version detection and voltage tables for TI TPS6586x PMIC devices
- Simplification of Freescale MC13XXX (de-)initialisation routines
- Clean-up and simplification of the Realtek parent driver
- Added support for RTL8402 Realtek PCI-Express card reader
- Resource leak fix for Maxim 77686
- Possible suspend BUG() fix in OMAP USB TLL
- Support for new Wolfson WM5110 Revision (D)
- Testing of automatic assignment of of_node in mfd_add_device()
- Reversion of the above when it started to cause issues
- Remove legacy Platform Data from;
TI TWL Core, Qualcomm SSBI and ST-E ABx500 Pinctrl
- Clean-ups; tabbing issues, function name changes, 'drvdata = NULL'
removal, unused uninitialised warning mitigation, error
message clarity, removal of redundant/duplicate checks,
licensing (GPL -> GPL2), coding consistency, duplicate
function declaration, ret checks, commit corrections,
redundant of_match_ptr() helper removal, spelling,
#if-deffery removal and header guards name changes"
* tag 'mfd-3.14-1' of git://git.linaro.org/people/ljones/mfd: (78 commits)
mfd: wm5110: Add register patch for rev D chip
mfd: omap-usb-tll: Don't hold lock during pm_runtime_get/put_sync()
gpio: lp3943: Remove redundant of_match_ptr helper
mfd: sta2x11-mfd: Use named constants for pci_power_t values
Documentation: mfd: Fix LDO index in s2mps11.txt
mfd: Cleanup mfd-mcp-sa11x0.h header
mfd: max8997: Use "IS_ENABLED(CONFIG_OF)" for DT code.
mfd: twl6030: Fix endianness problem in IRQ handler
mfd: sec-core: Add cells for S5M8767-clocks
mfd: max14577: Remove redundant of_match_ptr helper
mfd: twl6040: Fix sparse non static symbol warning
mfd: Revert "mfd: Always assign of_node in mfd_add_device()"
mfd: rtsx: Fix sparse non static symbol warning
mfd: max77693: Set proper maximum register for MUIC regmap
mfd: max77686: Fix regmap resource leak on driver remove
mfd: Represent correct filenames in file headers
mfd: rtsx: Add support for card reader rtl8402
mfd: rtsx: Add set pull control macro and simplify rtl8411
mfd: max8997: Enforce mfd_add_devices() return value check
mfd: mc13xxx: Simplify probe() & remove()
...
Currently everytime we get the following message on boot:
fsl-ssi-dai 202c000.ssi: could not get baud clock: -2
This is not really useful information to get on every boot, so make it a debug
message instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit aafa85e71a (ASoC: fsl_ssi: Add DAI master mode support for SSI on
i.MX series) master mode is supported, so update the comments and code to
reflect that.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Symbol MFD_MC13783 always selected by MFD_MC13XXX, so no need
to keep additional symbol.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
SNDRV_PCM_RATE_CONTINUOUS means that all rates (possibly limited to a certain
interval) are supported. There is no need to manually set other rate bits.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch implements a device-tree-only CPU DAI driver for Freescale ESAI
controller that supports:
- 12 channels playback and 8 channels record.
[ Some of the inner transmitters and receivers are sharing same group of
pins. So the maxmium 12 output or 8 input channels are only valid if
there is no pin conflict occurring to it. ]
- Independent (asynchronous mode) or shared (synchronous mode) transmit and
receive sections with separate or shared internal/external clocks and frame
syncs, operating in Master or Slave mode.
[ Current ALSA seems not to allow CPU DAI drivers to configure DAI format
separately for PLAYBACK and CAPTURE. So this first version only supports
the case that uses the same DAI format for both directions. ]
- Various DAI formats: I2S, Left-Justified, Right-Justified, DSP-A and DSP-B.
- Programmable word length (8, 16, 20 or 24bits)
- Flexible selection between system clock or external oscillator as input
clock source, programmable internal clock divider and frame sync generation.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For those platforms using DAI master mode like I2S, it's better to pre-set
a default slot number so that there's no need for these common cases to set
the slot number from its machine driver any more.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add the missing clk_disable_unprepare() before return from
fsl_ssi_probe() in the request irq error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
single_open requires a function with signature
'int (*)(struct seq_file *, void *)'. This patch fixes the warning by
fixing the wrong return type of fsl_ssi_stats_show.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The normal trigger function can now be used for AC97. Drop AC97 trigger
function.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch defines the appropriate register values for different
oparation modes and IP versions. We have to handle DMA/FIQ, AC97,
DEBUG-IRQs and offline/online configuration support.
With this patch we cleanup some driver code that was not reference
manual conform and try to cleanup the whole trigger function to seperate
the actual register values from the enable/disable logic, which is now
hidden in fsl_ssi_config helpers.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds a struct 'fsl_ssi_rxtx_reg_val' which holds register
values necessary to enable rx/tx. Based on those preset register values,
the added configuration functions will cleanly enable/disable different
parts of the SSI IP while supporting online/offline configuration.
Different operating modes can be setup directly as different register
values in fsl_ssi_reg_val.
These functions and structs will help to cleanup and simplify the
trigger function to support many different IP versions (online/offline
configuration) and different operating modes.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
imx50-ssi and later versions of this IP support online reconfiguration
of all registers. The reference manual does not list any registers that
can only be configured while the SSI unit is disabled. This patch
introduces the flag for later use.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
irqs should only be requested/released with enabled DMA. Previously
interrupt statistics where disabled for IMX Processors because of
different writeable SISR bits.
This patch introduces support for irqstats on imx processors again by
creating a sisr writeback mask and introducing a imx35-ssi compatible.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is a small but significant difference between imx21-ssi and
imx51-ssi and above. imx21-ssi does not allow online reconfiguration of
some registers. They have to be configured at the beginning.
imx51-ssi has to reconfigure the SSI unit while it is running. Otherwise
it would not be possible to have two streams in parallel. The new SDMA
unit in imx51 and above has to be configured before the first DMA
request arrives. Therefor we need to setup TDMAE/RDMAE just before
starting the stream.
This patch introduces distinct imx51-ssi as compatible and adds
of_device_id matching in the probe function.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Interrupt statistics of fsl_ssi are mainly for debugging purpose. Most
of those interrupts show error states, e.g. under/overflow.
The stats should be exposed via debugfs instead of sysfs.
This patch moves the statistics file to debugfs.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch fixes the error handling in the fsl-ssi probe function.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 6873ee464a (ASoC: fsl_ssi: Fix printing return code on clk error) caused
the following build warning:
sound/soc/fsl/fsl_ssi.c: In function 'fsl_ssi_probe':
sound/soc/fsl/fsl_ssi.c:1196:6: warning: format '%d' expects argument of type 'int', but argument 3 has type 'long int' [-Wformat]
Fix it by using '%ld' to print the 'long int' format.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
