Only initialize force feedback for devices that actually support it (Sixaxis and
Dualshock 4) to prevent calls to schedule_work() with an uninitialized work
queue.
Move the cancel_work_sync() call out of sony_destroy_ff() since the state worker
is used for the LEDs even when force-feedback is disabled.
Remove the sony_destroy_ff() function since it is no longer used.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Convert multi-line comments to comply with the kernel coding style.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a SIXAXIS_CONTROLLER macro to simplify conditionals where the
connection type is irrelevant.
Enable the LED and force feedback controls for Sixaxis controllers connected via
Bluetooth.
Send Sixaxis Bluetooth output reports on the control channel.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The battery_charging and cable_state flags were backwards on the Sixaxis.
The low bit of report byte 30 is 0 when charging and 1 when not.
Bit 5 of byte 31 is 0 when a USB cable is connected and 1 when not.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add the conditionals to enable rumble, battery reporting, LED and touchpad
support for the Dualshock 4 in Bluetooth mode.
Add dualshock4_set_operational_bt to initialize the controller to the proper
operational state.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Set the initial battery level to 100% to avoid false low battery warnings if
the battery state is polled before a report with the actual battery level is
received.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add Dualshock 4 battery and touchpad parsing for Bluetooth reports.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add formating for the Dualshock 4 output report data in Bluetooth mode.
In Bluetooth mode the Dualshock 4 wants output reports sent on the control
channel.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
By default, the Dualshock 4 sends controller data via report 1. Once a valid
output report 0x11 is received or a feature report of type 0x02 is requested the
controller changes from sending data in report 1 to sending data in report 17,
which is unmapped in the default descriptor. The mappings have to be moved to
report 17 to let the HID driver properly process the incoming reports.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Switch to the low-level transport driver functions.
sony_set_output_report is removed since it is no longer used.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a helper to access hdev->hid_output_raw_report().
To convert the drivers, use the following snippets:
for i in drivers/hid/*.c
do
sed -i.bak "s/[^ \t]*->hid_output_raw_report(/hid_output_raw_report(/g" $i
done
Then manually fix for checkpatch.pl
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
dev->hid_get_raw_report(X) and hid_hw_raw_request(X, HID_REQ_GET_REPORT)
are strictly equivalent. Switch the hid subsystem to the hid_hw notation
and remove the field .hid_get_raw_report in struct hid_device.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Well, no use to keep twice the same code.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
All the different transport drivers use now the generic event handling
in hid-input. We can remove the handler definitively now.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hid-logitech-dj uses its own ->hidinput_input_event() instead of
the generic binding in hid-input.
Moving the handling of LEDs towards logi_dj_output_hidraw_report()
allows two things:
- remove hidinput_input_event in struct hid_device
- hidraw user space programs can also set the LEDs
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Dualshock4 controller contains a RGB LED, which is enabled via
the '/sys/class/leds' interface. At present the driver only returns
whether each of the RGB LEDs is lit (ie not off), but no indication
of it's brightness.
This patch fixes the reading of the current brightnes so that it
returns the value (rather than just off=0, on=LED_FULL).
Tested on the DS4 and SixAxis (for compatibility).
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Update the HID_SONY config with 'select POWER_SUPPLY' to fix build issues
relating to undefined references to the power_supply_* functions in
certain build configurations.
Update the description text to reflect that Playstation 4 controllers are now
supported.
[jkosina@suse.cz: drop the POWER_SUPPLY hunk, as I've already fixed that]
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Sony driver now makes use of power supply support. Make kernel
config aware of it.
Reported-by: fengguang.wu@intel.com
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add the uhid_output_report transport-driver function to the uhid driver.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Acked-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add raw_request, set_raw_report and output_report transport-driver functions to
the USB HID driver.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Acked-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add output events for the multi-touch pad on the Dualshock 4.
The touchpad has a resolution of 1920x940 and is capable of 2 simultaneous
touches. A 'Type B' stateful slot protocol is implemented as defined in
Documentation/input/multi-touch-protocol.txt
Applications can use the touchpad data by processing the ABS_MT_SLOT,
ABS_MT_TRACKING_ID, ABS_MT_POSITION_X and ABS_MT_POSITION_Y events.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add battery status reporting for the Sixaxis and Dualshock 4 controllers.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use the naming scheme 'devicename:colour' for the Dualshock 4
LED lightbar controls as specified in Documentation/leds/leds-class.txt
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Retrieve and cache the output report for the Dualshock 4 in sony_probe()
instead of repeatedly walking the report list in the worker function.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use a modified HID descriptor for the Dualshock 4 to assign the gyroscope
sensors and accelerometers to axes.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use regular HID output reports instead of raw reports in the
dualshock4_state_worker function. (Thanks Simon Mungewell)
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use separate identifiers for Dualshock 4 controllers connected via USB and
Bluetooth.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This addresses regression caused by commit id "751d17e23a9f7"
iio: hid-sensors: Fix power and report state.
This commit removed a quirk, to change the enumeration base
to 1 from 0 based on an CONFIG paramter. There was objection to
add more changes under this quirk, instead suggested to add an
HID quirk. But there is no easy way to add HID qurik as the
reports are not properly using collection class.
The solution was to use logical minimum, which is a correct way.
There were changes done in firmware to address this.
Unfortunately some devices, still use old FW and can't be upgraded
to newer version on Linux devices as there is no FW upgrade tool
available for Linux devices. So we need to fix report descriptors,
for such devices. This will not have any impact, if the FW uses
logical 1 as minimum.
In this patch we look for usage id for "power and report state", and
modify logical minimum value to 1.
Background on enum:
In the original HID sensor hub firmwares all Named array enums were
to 0-based. But the most recent hub implemented as 1-based,
because of the implementation by one of the major OS vendor.
Using logical minimum for the field as the base of enum. So we add
logical minimum to the selector values before setting those fields.
Some sensor hub FWs already changed logical minimum from 0 to 1
to reflect this and hope every other vendor will follow.
There is no easy way to add a common HID quirk for NAry elements,
even if the standard specifies these field as NAry, the collection
used to describe selectors is still just "logical".
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This fix (not very clean though) should fix the long time USB3
issue that was spotted last year. The rational has been given by
Hans de Goede:
----
I think the most likely cause for this is a firmware bug
in the unifying receiver, likely a race condition.
The most prominent difference between having a USB-2 device
plugged into an EHCI (so USB-2 only) port versus an XHCI
port will be inter packet timing. Specifically if you
send packets (ie hid reports) one at a time, then with
the EHCI controller their will be a significant pause
between them, where with XHCI they will be very close
together in time.
The reason for this is the difference in EHCI / XHCI
controller OS <-> driver interfaces.
For non periodic endpoints (control, bulk) the EHCI uses a
circular linked-list of commands in dma-memory, which it
follows to execute commands, if the list is empty, it
will go into an idle state and re-check periodically.
The XHCI uses a ring of commands per endpoint, and if the OS
places anything new on the ring it will do an ioport write,
waking up the XHCI making it send the new packet immediately.
For periodic transfers (isoc, interrupt) the delay between
packets when sending one at a time (rather then queuing them
up) will be even larger, because they need to be inserted into
the EHCI schedule 2 ms in the future so the OS driver can be
sure that the EHCI driver does not try to start executing the
time slot in question before the insertion has completed.
So a possible fix may be to insert a delay between packets
being send to the receiver.
----
I tested this on a buggy Haswell USB 3.0 motherboard, and I always
get the notification after adding the msleep.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Rename sony_state_worker to sixaxis_state_worker since the function is now
sixaxis specific.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add LED lightbar controls for the Dualshock 4.
The Dualshock 4 light bar has 3 separate RGB LEDs that can range in
brightness from 0 to 255 so a full byte is now needed to store each LED's
state
Changed the module to support an arbitrary number of LEDs instead of being
hardcoded to 4.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds the Dualshock 4 to the HID device list and enables force-feedback.
Adds a Dualshock 4 specific worker function since the Dualshock 4 needs a
different report than the Sixaxis.
The right motor in the Dualshock 4 is variable so the full rumble value
is now passed to the worker function and clamped there if necessary.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently the return variable ret is always 0. Set it to other values in
error cases, as used in the direct return.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
we used to set the parent of the input device as the parent of
the hid bus. This was introduced when we created hid as a real bus, and
to keep backward compatibility. Now, it's time to proper set the parent
so that sysfs has an idea of which input device is attached to
which hid device.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add labels for BTN_DPAD_UP, BTN_DPAD_DOWN, BTN_DPAD_LEFT, BTN_DPAD_RIGHT and
BTN_TOOL_QUADTAP.
[jkosina@suse.cz: make changelog more verbose]
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
For 0xff05 usage in MS ergonomy keyboard quirk, we are falling through
and returning 0 instread of properly (because we've performed new mapping)
returning 1. Fix that.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix kernel warning and failure to register sensor hub devices with MFD. Now
many devices has in-built sensor hubs. So by default this HID hub, is properly
parsed and register individual sensors as platform device using MFD framework.
But if a second sensor hub is attached via USB, which has same sensors, it will
result in kernel warning and failure to register MFD cell as the platform
device sysfs file name will be same as created by in-built sensor hubs. This
patch sets MFD cell id to PLATFORM_DEVID_AUTO. In this way there will never be
duplicate sysfs file names.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2 fixes here.
* The gp2ap020a00f is a simple missing kconfig dependency.
* The hid sensors hub fix is a work around for an issue introduced by hardware
changes due to a certain large software vendor having an 'interesting'
interpretation of the specification and hence indexing some arrays from 1
rather than 0. The fix takes advantage of the logical min and max reading
facilities introduced by the precursor patch to figure out whether we have
a 0 indexed or 1 indexed device and to adjust appropriately. It also
drops a previous kconfig option that allowed this issue to be worked around
at build time.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=BgVg
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-3.13b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second round of IIO fixes for the 3.13 cycle.
2 fixes here.
* The gp2ap020a00f is a simple missing kconfig dependency.
* The hid sensors hub fix is a work around for an issue introduced by hardware
changes due to a certain large software vendor having an 'interesting'
interpretation of the specification and hence indexing some arrays from 1
rather than 0. The fix takes advantage of the logical min and max reading
facilities introduced by the precursor patch to figure out whether we have
a 0 indexed or 1 indexed device and to adjust appropriately. It also
drops a previous kconfig option that allowed this issue to be worked around
at build time.
hid-logitech-dj.c driver needs hidraw to work correctly. Without
hidraw, hid-logitech-dj.c fails during probe() and Logitech
Unifying devices HID reports aren't recognized.
The unifying receiver has 3 usb interfaces. When hid-logitech-dj driver is
loaded, interfaces 0 and 1 are discarded.
Interface 2 consists of a hid class interface with 3 collections, each of
which sports the 'vendor' usage, thus, there is no reason for hid_input to
claim any of them. On the other hand, hidraw has no issue in claiming the
collections, even if they are 'vendor'. As of today, hid-logitech-dj uses
hidraw api to send configuration/control reports to interface 2 of the
Unifying receiver.
Without the hid-logitech-dj driver, interfaces 0 and 1 are claimed by
hid-input, as they correspond to a keyboard and a mouse. But that is not
relevant to the discussion.
[jkosina@suse.cz: make the changelog more verbose, thanks to Nestor]
Signed-off-by: Olivier Gay <ogay@logitech.com>
Signed-off-by: Nestor Lopez Casado <nlopezcasad@logitech.com>
Signed-off-by: Mathieu Meisser <mmeisser@logitech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
I have two Logitech Dual Action gamepads, both have same Vendor/Device id pair.
Newest gamepad (A) can switch between old mode (HID) and XBox gamepad emulation
mode. Old gamepad (B) can only work in HID mode. In HID mode gamepad A sends
many EPIPE errors during initialization and was disconnected immediately after
connect to usb port. It works fine in Win and Mac. After adding NOGET quirk in
driver, it was working properly. Gamepad B works fine before and after
changes. I tested both gamepads with 3.8.0 and 3.11.6 kernels with modified
driver. Follow patch can apply for current git kernel version. I can send pcap
log from usb bus with both gamepads or any other additional information if it
is needed
Signed-off-by: Vitaly Katraew <zawullon@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Exporting logical minimum and maximum of HID fields as part of the
hid sensor attribute info. This can be used for range checking and
to calculate enumeration base for NAry fields of HID sensor hub.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
