Add/clarify comments and debug messages for interrupt used only for uCode load
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Invoke workaround to avoid instability in L0->L0S->L1 transition on PCIe bus.
Workaround disables L0S state so device moves directly from L0->L1.
Workaround needed on all devices since and including 4965; add to 6000/1000.
Describe bug and workaround better in comments.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To save power, don't run apm_ops.init() until needed at "up" time.
EEPROM (5000 and earlier devices) may be read without running apm_ops.init(),
but OTP reads (6000 and newer devices) require a powered-up chip.
Therefore, remove apm_ops.init() from the general path in XXXX_pci_probe(),
and call it only if device uses OTP. Once done with OTP read, call
apm_ops.stop() to reset chip and save power until "up" time comes around.
NOTE: This patch depends on removal of priv->lock from iwl_apm_stop();
lock does not get initialized until later in flow. See patch
"remove unneeded locks from apm_stop()".
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since priv->reg_lock was added to keep multi-access register manipulation
atomic, priv->lock protection is no longer needed. Remove this from
iwl_apm_stop_master() and iwl_apm_stop().
Add warning of timeout when polling for busmaster disablement confirmation,
and some comments.
NOTE: This is needed to enable use of apm_ops.stop() within iwl_eeprom_init();
priv->lock does not get initialized until after this flow. See patch
"remove power-wasting calls to apm_ops.init()"
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By setting the firmware version in wiphy it is possible to obtain this
information via ethtool. Some examples,
# ethtool -i wlan1
driver: iwlagn
version: 2.6.32-rc5-wl-56840-g26d8540
firmware-version: 228.57.2.23
bus-info: 0000:03:00.0
# ethtool -i wlan0
driver: iwl3945
version: 2.6.32-rc5-wl-56840-g26d8540
firmware-version: 15.28.2.8
bus-info: 0000:02:00.0
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the WLAN_PRE80211 drivers moved to drivers/staging, this
distinction becomes unnecessary.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'COEX_PRIORITY_TABLE_CMD' host command will be supported for 5000 series
and up.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add unconditional call to apm_ops.stop() to reset device to low power state
when unloading driver. Some paths have existed to unload driver *without*
resetting device, therefore some errors have persisted through multiple
load/unload cycles, until the whole platform gets rebooted; this is an
attempt to remedy some of those situations. Sorry, I can't seem to find
a bughost.org bug that specifically has these symptoms, but I had it happen
recently here.
Note that this will *not* fix situations in which the PCI express bus has
crashed (evidenced by register reads showing "0xffffffff"), e.g. bughost.org
1855 and 2096; device is unreachable from driver in those cases.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For 6x00 and 6x50 series devices, APIv4 is the lowest firmware version
driver can support. This is also the lowest API version available to the
public so there is no need for backward compatibility support for the
earlier API versions.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Duplicated define for listen interval (IWL_CONN_MAX_LISTEN_INTERVAL and
IWL_CONN_LISTEN_INTERVAL), remove IWL_CONN_LISTEN_INTERVAL
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Reported-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For notification packets and SKBs that fail to rx correctly, add
them back into the rx_free list so that the pages can be reused
later. This avoids allocating new rx pages unnecessarily.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
parameters "len" is not used in both iwl_tx_queue_free() and
iwl_cmd_queue_free() functions
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX_FREE_BUFFERS and RX_LOW_WATERMARK are currently defined in four places.
Based on how files are included we only need the definition in iwl-fh.h
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reported-by: Frans Pop <elendil@planet.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Support "channel switch" request by issue "channel switch" host command
to uCode.
There is no separated "channel switch" indication from mac80211,
when detected "IEEE80211_CONF_CHANGE_CHANNEL" flag in iwl_mac_config(),
if the station is in "associated" state, then assume "channel switch
announcement" IE was received by mac80211.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using device configuration structure to decide how to configure
ct_kill host command.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using device configuration structure to decide the type of thermal
throttle method for the device.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Increase the size of TFD_MAX_PAYLOAD_SIZE (the size of iwl_device_cmd)
to accommodate iwl6000_channel_switch_cmd data structure.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Acked-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the paged rx patch (4854fde2), I introduced a bug that could possibly
touch an already freed page. It is fixed by avoiding the access in this
patch. I've also added some comments so that other people touching the
code won't make the same mistake. In the future, if we cannot avoid
access the page after being handled to the upper layer, we can use
get_page/put_page to handle it. For now, it's just not necessary.
It also fixed a debug message print bug reported by Stanislaw Gruszka
<sgruszka@redhat.com>.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Specify both Tx and Rx chain in device configuration structure instead
of hard code in set_hw_params() for 4965
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Detach led background task from statistic notification routine. if led
blinking is required; the blink rate is based on the traffic condition.
It do not relate to statistics notification. In addition to that, there is
not a requirement for statistics notification has to occur all the time.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Consolidate most iwlXXXX_apm_init() functions into single iwl_apm_init().
Keep iwl3945_apm_init(), but leverage iwl_apm_init() for most functionality.
Update 4965 init sequence to follow most recent factory recommendations.
Add following members to struct iwl_cfg to guide the init sequence:
pll_cfg_val (replaces needs_pll_cfg), set_l0s, use_bsm
Move L0S enable/disable from nic_config() functions to iwl_apm_init().
This satisifies the "FIXME: put here L1A -L0S w/a" notice, and complies
with factory-recommended sequence.
Add debug info message in iwl_apm_init(), and symmetrical message
in iwl_apm_stop().
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In Rx gain balancing (chain noise) computation for 5000 series and up,
the delta gain calculation should use the average noise of default
chain, not "chain 0" which do not exist for all the devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Two commands missing from list of commands such that when debug is
enabled, these commands are shown as UNKNOWN.
Missing commands are TX_ANT_CONFIGURATION_CMD and
TEMPERATURE_NOTIFICATION.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For static power save, the actual intervals are calculated by driver based on
the default table and DTIM flag, then sent to uCode when the scheme
is changed.
Three tables are defined based on DTIM period.
1. DTIM 0 - 2
2. DTIM 3 - 10
3. DTIM > 11
The actual number of DTIM a station may miss may not exceed the
following:
. Only 1 DTIM may be skipped at PI=4 when allowed
. Only 2 DTIMs may be skipped at PI=5 when allowed
. DTIM may be skipped only 5 sec after last activity
. DTIM may be skipped only 30 sec after connection establishment
Only allow user to override the power_level when rf is ready to make sure
power level gets changed upon request.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For initial bring up of 6x50 series NICs, no chain noise support in
uCode, this feature will be added in the later stage of development.
Two chain noise related functions are removed from 6x50 series:
1. gain computation
2. chain noise reset
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For 6x00 and 6x50 series NIC with OTP shadow RAM, set auto clock gate
disable bit when initializing OTP access.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently mac80211 initializes the rate scaling before notifying the driver
of the station's existence. The driver dealt with this by not relying on
mac80211's station notifications and instead mixing this functionality with
the rate scaling code and other places. To clean this up the driver needs
to do rate scaling initialization after being notified of the station, this
can be done if the rate scaling information forms part of the station
information passed from mac80211 to driver.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move to header file so they can be included and used in other parts of the
driver.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function is only used in iwlagn so there is no need to have it in
iwlcore.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For 6x50 series, number of OTP blocks is different from 6x00 series
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding support for 6x50 series EEPROM version check, 6x50 is wifi/wimax
combo device which has different EEPROM map
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Power save request is sent from driver to uCode, but there is no
indication from uCode about the current device power save state.
Reading GP_CNTRL register bit 25:24 to show the current power save
status
00: no power save
01: MAC power down
10: PHY power down
11: Error
The uCode could switch in and out of power save mode in the order of
once per 100-300 ms in many cases. The reading here should just be used for
reference on the current uCode power save status. Do not confuse this
reading with the PowerSave set by driver and mac80211.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable the all the tx fifos while stopping the tx queues.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This switches the iwlwifi driver to use paged skb from linear skb for Rx
buffer. So that it relieves some Rx buffer allocation pressure for the
memory subsystem. Currently iwlwifi (4K for 3945) requests 8K bytes for
Rx buffer. Due to the trailing skb_shared_info in the skb->data,
alloc_skb() will do the next order allocation, which is 16K bytes. This
is suboptimal and more likely to fail when the system is under memory
usage pressure. Switching to paged Rx skb lets us allocate the RXB
directly by alloc_pages(), so that only order 1 allocation is required.
It also adjusts the area spin_lock (with IRQ disabled) protected in the
tasklet because tasklet guarentees to run only on one CPU and the new
unprotected code can be preempted by the IRQ handler. This saves us from
spawning another workqueue to make skb_linearize/__pskb_pull_tail happy
(which cannot be called in hard irq context).
Finally, mac80211 doesn't support paged Rx yet. So we linearize the skb
for all the management frames and software decryption or defragmentation
required data frames before handed to mac80211. For all the other frames,
we __pskb_pull_tail 64 bytes in the linear area of the skb for mac80211
to handle them properly.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Channel switch host command has different data structure for
different devices. Adding additional structures to support 5000 and 6000
NICs. unlike 4965, starting with 5000 series, the tx power is managed by
uCode, there is no tx power db information need to be passing from driver to
uCode; but the space needs to be reserved to match uCode expection.
1000 NIC do not support channel switch operation since it is 'bgn'
device, there is no need to have data structure defined for it.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rearrange the code and groups setting of
retry_limit and data_retry_limits code together.
Make 'data_retry_limit' setting similar to iwlwifi
for better readability.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the ununsed variable data_retry_limit
from priv.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 and 4965 share the functionality for setting RTS and CTS to
the tx_cmd. Unify these functions and move the common
functionality to core.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding accumulative statistics counters in iwlwifi driver.
Statistics counters are reported by uCode every beacon interval; but can
be reset by uCode when needed. The accumulative statistics counters is
maintained by driver to keep track of the history of all the counters.
Update the ucode stats files in debugfs to display both latest and
accumulative counters.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of always allocate the max number of tx queue structure,
use dynamic allocation based on the number of queues in device
configuration. With these changes, device does not have to allocate more
memory than the h/w can support.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl_power_initialize() initializes driver data (not device hardware), and does
not need to execute more than once (when the driver initializes). Therefore, it
does not belong in iwl3945_apm_init(), which initializes hardware, and may run
more than once.
Move it to iwl3945_pci_probe(), where it will run only once. This agrees
with similar placement in iwl-agn.c's iwl_pci_probe(), although placement
under "services" seemed more appropriate than under "mac80211".
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl3945_rfkill_poll() has been silently calling wiphy_rfkill_set_hw_state()
every 2 seconds, regardless of whether hardware RF KILL switch changed state.
Call wiphy_rfkill_set_hw_state() only when RFKILL switch changes.
Add IWL_DEBUG_RF_KILL log message and documentation.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sleep_level_override debugfs file is used by the user to request a
static power index instead of the dynamic sleep values. Users are expected
to provide value from 1 to 5 as an index or -1 to disable it.
The problem at the moment is that users can also provide 0 to this file
which, together with the value 1, is translated to index 1. This is
confusing and even more so when users write 0 to sleep_level_override and
then read 1 from it afterwards.
Modify checking to treat 0 as invalid.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add more items to sensitivity range table to avoid using hardcoded values.
Initialize the table per device since unique per device information is
required to perform sensitivity calibration.
additional items in sensitivity range table:
.barker_corr_th_min: Barker correlation threshold minimum
.barker_corr_th_min_mrc: Barker correlation threshold minimum for MRC
.nrg_th_cca: Energy threshold for Clear Channel Assessment
Barker codes are a technique used in WLAN encoding for transmission.
MRC is "Maximal Ratio Combining", a technique for optimally combining the
signals from 2 or more receivers to achieve a better signal.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"IWL_CMD_QUEUE_NUM" is being defined in multiple places and used by all
the devices. move it to iwl-dev.h file and shared by all the devices.
Remove "IWL_CMD_FIFO_NUM", replaced by "IWL49_CMD_FIFO_NUM" and IWL50_CMD_FIFO_NUM"
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean up device-specific apm_reset() functions and library infrastructure,
now that these reset() functions are no longer being used.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that we're unconditionally using apm_ops.stop() to reset and power-down
the device in __iwl3945_down(), the apm_ops.reset() is redundant. Removing
this call will also allow us to remove iwl3945_apm_reset().
Remove unneeded iwl_clear_bit(CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ) because
this bit will be set again very soon in iwl3945_hw_txq_ctx_stop() and other
following calls.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some cases (e.g. when mac80211 calls iwl_mac_stop() for suspend or user
no longer wants device active), device has not been going into low power state
via __iwl_down(). apm_ops.reset() does not put device into low power state;
instead it resets the device, then puts it into a powered-up state ready to be
re-loaded with uCode and re-started. This has needlessly warmed up user's
laptops and drained batteries.
With current architecture in which mac80211 controls device up/down (including
resetting device after firmware errors), there is no need for apm_ops.reset()
any more; apm_ops.reset() is basically a combination of apm_ops.stop() and
apm_ops.init().
Instead, __iwl_down() now unconditionally places the device into a low-power
state via apm_ops.stop(). Device may be re-started via __iwl_up() calling
apm_ops.init() as soon as it may be needed (e.g. quickly for firmware errors),
but in the meantime, device will stop wasting energy.
Note that, even in this low power state, if driver re-enables interrupts,
the device retains the ability to sense the hardware RF-KILL switch, and
(except for 3945) interrupt the host when it changes.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
