Commit 40ed51a4b (usb: chipidea: host: add vbus regulator
control) introduced a smatch complaint because regulator_disable() is called
without checking whether ci->platdata->reg_vbus is not NULL.
Fix this by adding the check.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
The correct way for a driver to specify the coherent DMA mask is
not to directly access the field in the struct device, but to use
dma_set_coherent_mask(). Only arch and bus code should access this
member directly.
Convert all direct write accesses to using the correct API.
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If the user chooses peripheral mode for this controller, the vbus
regulator doesn't need to get, since the host will supply the vbus,
it can save one vbus pin for other usage.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Frank Li <frank.li@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like http://marc.info/?l=linux-usb&m=138200449428874&w=2 said:
two more things are needed to be done:
- If host_start fails, the host_stop should not be called, so we
add check that ci->hcd is not NULL.
- if the host_start fails at the beginning, we need to consider
regulator mismatch issue.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CMA fails to initialize in v3.12-rc4, the chipidea driver oopses
the kernel while trying to remove and put the HCD which doesn't exist:
WARNING: CPU: 0 PID: 6 at /home/rmk/git/linux-rmk/arch/arm/mm/dma-mapping.c:511
__dma_alloc+0x200/0x240()
coherent pool not initialised!
Modules linked in:
CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G W 3.12.0-rc4+ #56
Workqueue: deferwq deferred_probe_work_func
Backtrace:
[<c001218c>] (dump_backtrace+0x0/0x10c) from [<c0012328>] (show_stack+0x18/0x1c)
r6:c05fd9cc r5:000001ff r4:00000000 r3:df86ad00
[<c0012310>] (show_stack+0x0/0x1c) from [<c05f3a4c>] (dump_stack+0x70/0x8c)
[<c05f39dc>] (dump_stack+0x0/0x8c) from [<c00230a8>] (warn_slowpath_common+0x6c/0x8c)
r4:df883a60 r3:df86ad00
[<c002303c>] (warn_slowpath_common+0x0/0x8c) from [<c002316c>] (warn_slowpath_fmt+0x38/0x40)
r8:ffffffff r7:00001000 r6:c083b808 r5:00000000 r4:df2efe80
[<c0023134>] (warn_slowpath_fmt+0x0/0x40) from [<c00196bc>] (__dma_alloc+0x200/0x240)
r3:00000000 r2:c05fda00
[<c00194bc>] (__dma_alloc+0x0/0x240) from [<c001982c>] (arm_dma_alloc+0x88/0xa0)
[<c00197a4>] (arm_dma_alloc+0x0/0xa0) from [<c03e2904>] (ehci_setup+0x1f4/0x438)
[<c03e2710>] (ehci_setup+0x0/0x438) from [<c03cbd60>] (usb_add_hcd+0x18c/0x664)
[<c03cbbd4>] (usb_add_hcd+0x0/0x664) from [<c03e89f4>] (host_start+0xf0/0x180)
[<c03e8904>] (host_start+0x0/0x180) from [<c03e7c34>] (ci_hdrc_probe+0x360/0x670
)
r6:df2ef410 r5:00000000 r4:df2c3010 r3:c03e8904
[<c03e78d4>] (ci_hdrc_probe+0x0/0x670) from [<c0311044>] (platform_drv_probe+0x20/0x24)
[<c0311024>] (platform_drv_probe+0x0/0x24) from [<c030fcac>] (driver_probe_device+0x9c/0x234)
...
---[ end trace c88ccaf3969e8422 ]---
Unable to handle kernel NULL pointer dereference at virtual address 00000028
pgd = c0004000
[00000028] *pgd=00000000
Internal error: Oops: 17 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G W 3.12.0-rc4+ #56
Workqueue: deferwq deferred_probe_work_func
task: df86ad00 ti: df882000 task.ti: df882000
PC is at usb_remove_hcd+0x10/0x150
LR is at host_stop+0x1c/0x3c
pc : [<c03cacec>] lr : [<c03e88e4>] psr: 60000013
sp : df883b50 ip : df883b78 fp : df883b74
r10: c11f4c54 r9 : c0836450 r8 : df30c400
r7 : fffffff4 r6 : df2ef410 r5 : 00000000 r4 : df2c3010
r3 : 00000000 r2 : 00000000 r1 : df86b0a0 r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c53c7d Table: 2f29404a DAC: 00000015
Process kworker/u2:0 (pid: 6, stack limit = 0xdf882240)
Stack: (0xdf883b50 to 0xdf884000)
...
Backtrace:
[<c03cacdc>] (usb_remove_hcd+0x0/0x150) from [<c03e88e4>] (host_stop+0x1c/0x3c)
r6:df2ef410 r5:00000000 r4:df2c3010
[<c03e88c8>] (host_stop+0x0/0x3c) from [<c03e8aa0>] (ci_hdrc_host_destroy+0x1c/0x20)
r5:00000000 r4:df2c3010
[<c03e8a84>] (ci_hdrc_host_destroy+0x0/0x20) from [<c03e7c80>] (ci_hdrc_probe+0x3ac/0x670)
[<c03e78d4>] (ci_hdrc_probe+0x0/0x670) from [<c0311044>] (platform_drv_probe+0x20/0x24)
[<c0311024>] (platform_drv_probe+0x0/0x24) from [<c030fcac>] (driver_probe_device+0x9c/0x234)
[<c030fc10>] (driver_probe_device+0x0/0x234) from [<c030ff28>] (__device_attach+0x44/0x48)
...
---[ end trace c88ccaf3969e8423 ]---
Fix this so at least we can continue booting and get to a shell prompt.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Also clean up the last item of the pci id list to be "cleaner".
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This API is used to let the PHY enter/leave low power mode.
Before the controller going to work(at probe/resume), it needs to let
the PHY leave low power mode.
After the controller stopping working(at remove/suspend), it needs to
let the PHY enter low power mode to save power consumption.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the PHY operations are moved to core, delete the related
code at glue layer.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PHY operations are common, so move them to core.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If NO_DMA=y:
drivers/built-in.o: In function `dma_set_coherent_mask':
include/linux/dma-mapping.h:93: undefined reference to `dma_supported'
Reviewed-and-tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a pending TD which is not freed after request finishes,
we do this due to a controller bug. This TD needs to be freed when
the driver is removed. It prints below error message when unload
chipidea driver at current code:
"ci_hdrc ci_hdrc.0: dma_pool_destroy ci_hw_td, b0001000 busy"
It indicates the buffer at dma pool are still in use.
This commit will free the pending TD at driver's removal procedure,
it can fix the problem described above.
Acked-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If not, the PHY will be active even the controller is not in use.
We find this issue due to the PHY's clock refcount is not correct
due to -EPROBE_DEFER return after phy's init.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It needs to free ci->hw_bank.regmap explicitly since it is not managed
resource.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like vbus, the dr_mode and phy_mode are also got from glue layer's
platform data or device node.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The udc-core will call gadget's driver->disconnect, so we should avoid
calling gadget's disconnect again at ci_udc_stop in case the gadget's
unbind free some structs which is still used at gadget's disconnect.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a pending TD which is not freed after request finishes,
we do this due to a controller bug. This TD needs to be freed when
the driver is removed. It prints below error message when unload
chipidea driver at current code:
"ci_hdrc ci_hdrc.0: dma_pool_destroy ci_hw_td, b0001000 busy"
It indicates the buffer at dma pool are still in use.
This commit will free the pending TD at driver's removal procedure,
it can fix the problem described above.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The chipidea i.MX driver is split into two drivers. The ci_hdrc_imx driver
handles the chipidea cores and the usbmisc_imx driver handles the noncore
registers common to all chipidea cores (but SoC specific). Current flow is:
- usbmisc sets an ops pointer in the ci_hdrc_imx driver during probe
- ci_hdrc_imx checks if the pointer is valid during probe, if yes calls
the functions in the ops pointer.
- usbmisc_imx calls back into the ci_hdrc_imx driver to get additional
data
This is overly complicated and has problems if the drivers are compiled
as modules. In this case the usbmisc_imx driver can be unloaded even if
the ci_hdrc_imx driver still needs usbmisc functionality.
This patch changes this by letting the ci_hdrc_imx driver calling functions
from the usbmisc_imx driver. This way the symbol resolving during module
load makes sure the ci_hdrc_imx driver depends on the usbmisc_imx driver.
Also instead of letting the usbmisc_imx driver call back into the ci_hdrc_imx
driver, pass the needed data in the first place.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For chipidea, the IP must know vbus before the controller
begins to run. So the .pullup should only be called when
the vbus is there.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the controller only runs when the ci->vbus_active is true.
So the flag CI_HDRC_PULLUP_ON_VBUS is useless no longer.
If the user doesn't have otgsc, he/she needs to change ci_handle_vbus_change
to update ci->vbus_active.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CI_HDRC_REGS_SHARED stands for the controller registers is shared
with other USB drivers, if all USB drivers are at chipidea/, it doesn't
needed to be set.
CI_HDRC_PULLUP_ON_VBUS stands for pullup dp when the vbus is on. This
flag doesn't need to be set if the vbus is always on for gadget
since dp has always pulled up after the gadget has initialized.
So, the current code seems to misuse this two flags.
- When the gadget initializes, the controller doesn't need to run if
it depends on vbus (CI_HDRC_PULLUP_ON_VBUS), it does not relate to
shared register.
- When the gadget starts (load one gadget module), the controller
can run if vbus is on (CI_HDRC_PULLUP_ON_VBUS), it also does not
relate to shared register.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the gadget role starts, we need to make sure the vbus is lower
than OTGSC_BSV, or there will be an vbus interrupt since we use
B_SESSION_VALID as vbus interrupt to indicate connect and disconnect.
When the host role starts, it may not be useful to wait vbus to lower
than OTGSC_BSV, but it can indicate some hardware problems like the
vbus is still higher than OTGSC_BSV after we disconnect to host some
time later (5000 milliseconds currently), which is obvious not correct.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We add vbus interrupt handler at ci_otg_work, it uses OTGSC_BSV(at otgsc)
to know it is connect or disconnet event.
Meanwhile, we introduce two flags id_event and b_sess_valid_event to
indicate it is an id interrupt or a vbus interrupt.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move otg related things to otg file.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During the initialization, it needs to disable all interrupts
enable bit as well as clear all interrupts status bits to avoid
exceptional interrupt.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we need otgsc to know vbus's status at some chipidea
controllers even it is peripheral-only mode. Besides, some
SoCs (eg, AR9331 SoC) don't have otgsc register even
the DCCPARAMS_DC and DCCPARAMS_HC are both 1 at CAP_DCCPARAMS.
We inroduce flag CI_HDRC_DUAL_ROLE_NOT_OTG to indicate if the
controller is dual role, but not supports OTG. If this flag is
not set, we follow the rule that if DCCPARAMS_DC and DCCPARAMS_HC
are both 1 at CAP_DCCPARAMS, then this controller is otg capable.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- The role's init will be called at probe procedure.
- The role's destroy will be called at fail patch
at probe and driver's removal.
- The role's start/stop will be called when specific
role has started.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This file is mainly used to access otgsc currently, it may
add otg related things in the future.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is useless at below cases:
- If we implement both usb host and device at chipidea driver.
- If we don't need phy->otg.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For boards which have board level vbus control (eg, through gpio), we
need to vbus operation according to below rules:
- For host, we need open vbus before start hcd, and close it
after remove hcd.
- For otg, the vbus needs to be on/off when usb role switches.
When the host roles begins, it opens vbus; when the host role
finishes, it closes vbus.
We put vbus operation to host as host is the only vbus user,
When we are at host mode, the vbus is on, when we are not at
host mode, vbus should be off.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vbus regulator is a common element for USB vbus operation,
So, move it from glue layer to core.
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the rename to ci_hdrc we ended up with two MODULE_ALIAS entries, so
remove the old one.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 40dcd0e ("usb: chipidea: add PTW, PTS and STS handling") introduced
the following code to the ci_hdrc_probe() function:
+ if (!dev->of_node && dev->parent)
+ dev->of_node = dev->parent->of_node;
This inadvertently associates the ci_hdrc device with the ci_hdrc_imx
driver (which created the ci_hdrc device in the first place).
This results in ci_hdrc_imx_probe() being run for the ci_hdrc device
if ci_hdrc_probe() fails for some reason.
ci_hdrc_imx_probe() will happily create a new ci_hdrc platform_device
whose probing will likewise fail and trigger a new invocation of
ci_hdrc_imx_probe() ... ad nauseam.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Reviewed-and-tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a role fails to start, propagate the error code up the call stack
from probe.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This prevents the USB PHY refcount to be decremented below zero upon
unloading the ci-hdrc-imx module.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch provides a cleaner solution to the problem described in
commit 20a677fd ("usb: chipidea: improve kconfig").
The goal to be achieved is to force USB_CHIPIDEA=m if either
USB_EHCI_HCD=m or USB_GADGET=m.
If both are 'y' USB_CHIPIDEA may be selected to be 'm' or 'y'.
The old patch had the drawback, that USB_CHIPIDEA could be chosen as
'y' though USB_EHCI_HCD or USB_GADGET (or both) were 'm' leading to a
situation where USB_CHIPIDEA_HOST or USB_CHIPIDEA_UDC vanished from
the config options producing a compilable but dysfunctional driver.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Reviewed-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove an unused macro leftover from the old initialization code.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently hw_phymode_configure() is located inside hw_device_reset(), which is
only called by chipidea udc driver.
When operating in host mode, we also need to call hw_phymode_configure() in
order to properly configure the PHY mode, so move this function into probe.
After this change, USB Host1 port on mx53qsb board is functional.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Reviewed-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'res' is not used anywhere, so let's get rid of it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All patches here have been pending on linux-usb
and sitting in linux-next for a while now.
The biggest things in this tag are:
DWC3 learned proper usage of threaded IRQ
handlers and now we spend very little time
in hardirq context.
MUSB now has proper support for BeagleBone and
Beaglebone Black.
Tegra's USB support also got quite a bit of love
and is learning to use PHY layer and generic DT
attributes.
Other than that, the usual pack of cleanups and
non-critical fixes follow.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=3NS9
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.12 merge window
All patches here have been pending on linux-usb
and sitting in linux-next for a while now.
The biggest things in this tag are:
DWC3 learned proper usage of threaded IRQ
handlers and now we spend very little time
in hardirq context.
MUSB now has proper support for BeagleBone and
Beaglebone Black.
Tegra's USB support also got quite a bit of love
and is learning to use PHY layer and generic DT
attributes.
Other than that, the usual pack of cleanups and
non-critical fixes follow.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/usb/gadget/udc-core.c
drivers/usb/host/ehci-tegra.c
drivers/usb/musb/omap2430.c
drivers/usb/musb/tusb6010.c
The has_hostpc capability bit indicates that the host controller has the
HOSTPC register extensions, but at the same time enables clock disabling
power saving features with the PHY Low Power Clock Disable (PHCD) bit.
However, some host controllers have the HOSTPC extensions but don't
support the low-power feature, so the PHCD bit must not be set on those
controllers. Add a separate capability bit for the low-power feature
instead, and change all existing users of has_hostpc to use this new
capability bit.
The idea for this commit is taken from an old 2012 commit that never got
merged ("disociate chipidea PHY low power suspend control from hostpc")
Inspired-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using below configs, the compile will have error:
ERROR: "ehci_init_driver" undefined!
.config:
CONFIG_USB_CHIPIDEA=m
CONFIG_USB_CHIPIDEA_HOST=y
CONFIG_USB_CHIPIDEA_DEBUG=y
The reason is chipidea host uses symbol from ehci, but ehci
is not compiled. Let the chipidea host depend on
ehci even it is built as module.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following build warnings on x86:
drivers/usb/chipidea/core.c: In function 'hw_phymode_configure':
drivers/usb/chipidea/core.c:226:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/usb/chipidea/core.c:230:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/usb/chipidea/core.c:243:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/usb/chipidea/core.c:246:3: warning: large integer implicitly truncated to unsigned type [-Woverflow]
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This branch contains the following changes:
- Removal of CONFIG_OF_DEVICE, it is always enabled by CONFIG_OF
- Remove #ifdef from linux/of_platform.h to increase compiler syntax
coverage
- Bug fix for address decoding on Bimini and js2x powerpc platforms.
- miscellaneous binding changes
One note on the above. The binding changes going in from all kinds of
different trees has gotten rather out of hand. I picked up some during
this cycle, but even going though my tree isn't a great fit. Ian
Campbell has prototyped splitting the bindings and .dtb files into a
separate repository. The plan is to migrate to using that sometime in
the next few kernel releases which should get rid of a lot of the churn
on binding docs and .dts files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=CndB
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux
Pull device tree updates from Grant Likely:
"This branch contains the following changes:
- Removal of CONFIG_OF_DEVICE, it is always enabled by CONFIG_OF
- Remove #ifdef from linux/of_platform.h to increase compiler syntax
coverage
- Bug fix for address decoding on Bimini and js2x powerpc platforms.
- miscellaneous binding changes
One note on the above. The binding changes going in from all kinds of
different trees has gotten rather out of hand. I picked up some
during this cycle, but even going though my tree isn't a great fit.
Ian Campbell has prototyped splitting the bindings and .dtb files into
a separate repository. The plan is to migrate to using that sometime
in the next few kernel releases which should get rid of a lot of the
churn on binding docs and .dts files"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
of: Fix address decoding on Bimini and js2x machines
of: remove CONFIG_OF_DEVICE
usb: chipidea: depend on CONFIG_OF instead of CONFIG_OF_DEVICE
of: remove of_platform_driver
ibmebus: convert of_platform_driver to platform_driver
driver core: move to_platform_driver to platform_device.h
mfd: DT bindings for the palmas family MFD
ARM: dts: omap3-devkit8000: fix NAND memory binding
of/base: fix typos
of: remove #ifdef from linux/of_platform.h
commit ea1418b5f1 (usb: chipidea: i.MX: use devm_usb_get_phy_by_phandle to get
phy) causes the USB host to miss the disconnect/connect events.
In order to reproduce this problem:
- Insert a USB thumb into the USB host port (connection is detected)
- Remove it (no disconnect event will be reported)
- Insert the USB thumb again (connection is not detected)
Fix this problem by accessing the usb_phy structure using the private data
instead of accessing a local structure.
Tested on a mx28evk board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"ci13xxx" is bad for at least the following reasons:
* people often mistype it
* it doesn't add any informational value to the names it's used in
* it needlessly attracts mail filters
This patch replaces it with "ci_hdrc", "ci_udc" or "ci_hw", depending
on the situation. Modules with ci13xxx prefix are also renamed accordingly
and aliases are added for compatibility. Otherwise, no functional changes.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow udev to autoload the module when booting with device-tree
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since someone has added camelcase detection to checkpatch.pl, chipidea
udc patches have been very noisy. To make everybody's life easier, this
patch changes camelcase names into something more appropriate to the
coding style. No functional changes.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes error path cleaner and probe function tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As drvdata is cleared to NULL at probe failure or at removal by the driver
core, we don't have to call pci_set_drvdata(pci, NULL) any longer in each
driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch converts the driver to use devm_usb_get_phy_by_phandle
which makes the code smaller and a bit simpler.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch converts the driver to use the module_platform_driver
macro which makes the code smaller and a bit simpler.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pdata structure gets copied anyway inside ci13xxx_add_device
by platform_device_add. We don't need to have it static.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even if a chipidea core is otg capable the board may not be. This allows
to explicitly set the core to host/peripheral mode. Without these flags
the driver falls back to the old behaviour.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes it possible to configure the PTW, PTS and STS bits
inside the portsc register for host and device mode before the driver
starts and the phy can be addressed as hardware implementation is
designed.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the restriction of having a limited amount of only
four active tds on one endpoint. We use the linked list implementation
to manage all tds which get added and removed by hardware_{en,de}queue.
The removal of this restriction adds the driver to run into a hardware
errata. It's possible that the hardware will still address an transfer
descriptor that already got cleaned up. To solve this the patch also
postpone the cleanup of processed tds by one.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of having a limited number of usable tds in the udc we use a
linked list to support dynamic amount of needed tds for all special
gadget types. This improves throughput.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Randy Dunlap <rdunlap@infradead.org> reported this problem
on i386:
> drivers/built-in.o: In function `ci_hdrc_host_init':
> (.text+0x2ce75c): undefined reference to `ehci_init_driver'
>
> When USB_EHCI_HCD=m and USB_CHIPIDEA=y.
In fact, this problem is existed on all platforms which are using
chipidea driver. The root cause of this problem is the chipidea host
uses symbol exported from ehci-hcd, but chipidea core
does not depends on USB_EHCI_HCD. So, chipidea driver
will not be compiled as module if USB_EHCI_HCD=m.
It is very hard to give a perfect solution since chipidea core
depends on USB || USB_GADGET, and chipdiea host depends on
both USB_EHCI_HCD and USB_CHIPIDEA, the same problem exists for
gadget.
To fix this problem, we had to have below assumptions:
- If USB_EHCI_HCD=y && USB_GADGET=y, USB_CHIPIDEA can be 'y'.
- If USB_EHCI_HCD=m && USB_GADGET=y, USB_CHIPIDEA=m
or USB_CHIPIDEA_HOST can't be seen if USB_CHIPIDEA=y.
It will cause compile error due to no glue layer for ehci:
> error: #error "missing bus glue for ehci-hcd"
So, we had to compile USB_CHIPIDEA=m if USB_EHCI_HCD=m,
current ehci hcd core guarantee it.
- If USB_EHCI_HCD=y && USB_GADGET=m, USB_CHIPIDEA=m
or USB_CHIPIDEA_UDC can't be seen if USB_CHIPIDEA=y.
Of cos, the gadget will out of working at this situation,
so the user had to compile USB_CHIPIDEA=m.
- USB_EHCI_HCD=m && USB_GADGET=m, we can't see
USB_CHIPIDEA_HOST and USB_CHIPIDEA_UDC unless
USB_CHIPIDEA=m.
The reason why it has above assumptions:
- If both ehci core and gadget core build as module,
the chipidea has to build as module.
- If one of ehci core or gadget core is built in, another
is built as module, we can only enable the function which
is built in, or enable both roles as modules (USB_CHIPIDEA=m),
since chipidea core driver takes care of both host and device roles.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to keep a local 'phy_np' as we can directly use the private
structure in data->phy_np.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similarly as it is done in ci13xxx_imx_remove(), only calls of_node_put if
data->phy_np is not NULL.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to keep a 'reg_vbus' indirection, so get rid of it.
The motivation for doing this change is that in the case of error, the current
code only sets the local reg_vbus to NULL instead of updating the private
structure 'data->reg_vbus'.
Updating only the local reg_vbus is wrong, since we currently check for
data->reg_vbus in the ci13xxx_imx_remove() function.
In order to avoid such issue, just use 'data->reg_vbus' directly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If usbmisc_ops->post() fails it should point the error path to release all
previously acquired resources, so adjust it to call ci13xxx_remove_device().
While at it, remove the unnecessary 'plat_ci' indirection, as we can directly
use the private structure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds iso endpoint support to the device controller.
It makes use of the multiplication bits in the maxpacket field
of the endpoint and calculates the multiplier bits for each
transfer description on every request.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following sparse warnings:
drivers/usb/chipidea/usbmisc_imx.c:246:5: warning: symbol 'usbmisc_imx_drv_init' was not declared. Should it be static?
drivers/usb/chipidea/usbmisc_imx.c:252:6: warning: symbol 'usbmisc_imx_drv_exit' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for handling pinctrl.
So remove devm_pinctrl_get_select_default() from the driver.
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_OF_DEVICE is going away, so use CONFIG_OF instead. It does not
appear that CONFIG_OF_DEVICE was the correct dependency either.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Re-enable chipidea irq even if there's no role changing to do. This is
a problem since b183c19f ("USB: chipidea: re-order irq handling to avoid
unhandled irqs"); when it manifests, chipidea irq gets disabled for good.
Cc: stable@vger.kernel.org # v3.7
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since usb phy code does return ERR_PTR() values, make sure that we don't
end up dereferencing them. This is a problem, for example, on platforms
that don't register a phy for chipidea since b7fa5c2a ("usb: phy: return
-ENXIO when PHY layer isn't enabled").
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pci_enable_device() will set device power state to D0,
so it's no need to do it again in ci13xxx_pci_probe().
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are a number of tiny USB bugfixes / new device ids for 3.10-rc2
The majority of these are USB gadget fixes, but they are all small.
Other than that, some USB host controller fixes, and USB serial driver
fixes for problems reported with them.
Also hopefully a fixed up USB_OTG Kconfig dependancy, that one seems to
be almost impossible to get right for all of the different platforms
these days.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlGeP/gACgkQMUfUDdst+ykXygCfeIL5/HMREhUSHQgb6IiIDR81
QHAAn0zJfRAyWUz4AtbrRsLSVfk3Q9vm
=DQIq
-----END PGP SIGNATURE-----
Merge tag 'usb-3.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are a number of tiny USB bugfixes / new device ids for 3.10-rc2
The majority of these are USB gadget fixes, but they are all small.
Other than that, some USB host controller fixes, and USB serial driver
fixes for problems reported with them.
Also hopefully a fixed up USB_OTG Kconfig dependancy, that one seems
to be almost impossible to get right for all of the different
platforms these days."
* tag 'usb-3.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (56 commits)
USB: cxacru: potential underflow in cxacru_cm_get_array()
USB: ftdi_sio: Add support for Newport CONEX motor drivers
USB: option: add device IDs for Dell 5804 (Novatel E371) WWAN card
usb: ohci: fix goto wrong tag in err case
usb: isp1760-if: fix memleak when platform_get_resource fail
usb: ehci-s5p: fix memleak when fallback to pdata
USB: serial: clean up chars_in_buffer
USB: ti_usb_3410_5052: fix chars_in_buffer overhead
USB: io_ti: fix chars_in_buffer overhead
USB: ftdi_sio: fix chars_in_buffer overhead
USB: ftdi_sio: clean up get_modem_status
USB: serial: add generic wait_until_sent implementation
USB: serial: add wait_until_sent operation
USB: set device dma_mask without reference to global data
USB: Blacklisted Cinterion's PLxx WWAN Interface
usb: option: Add Telewell TW-LTE 4G
USB: EHCI: remove bogus #error
USB: reset resume quirk needed by a hub
USB: usb-stor: realtek_cr: Fix compile error
usb, chipidea: fix link error when USB_EHCI_HCD is a module
...
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Marek Vasut <marex@denx.de>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many USB host drivers contain code such as:
if (!pdev->dev.dma_mask)
pdev->dev.dma_mask = &tegra_ehci_dma_mask;
... where tegra_ehci_dma_mask is a global. I suspect this code originated
in commit 4a53f4e "USB: ehci-tegra: add probing through device tree" and
was simply copied everywhere else.
This works fine when the code is built-in, but can cause a crash when the
code is in a module. The first module load sets up the dma_mask pointer,
but if the module is removed and re-inserted, the value is now non-NULL,
and hence is not updated to point at the new location, and hence points
at a stale location within the previous module load address, which in
turn causes a crash if the pointer is de-referenced.
The simplest way of solving this seems to be to copy the code from
ehci-platform.c, which uses the coherent_dma_mask as the target for the
dma_mask pointer.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes link error when USB_EHCI_HCD=m and USB_CHIPIDEA_HOST=y:
drivers/built-in.o: In function `ci_hdrc_host_init':
drivers/usb/chipidea/host.c:104: undefined reference to `ehci_init_driver'
as a result of commit 09f6ffde2e ("USB: EHCI: fix build error by making
ChipIdea host a normal EHCI driver").
Cc: stable@vger.kernel.org [v3.7+]
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big Gadget & PHY pull request. Many of us have
been really busy lately getting multiple drivers to a better
position.
Since this pull request is so large, I will divide it in sections
so it's easier to grasp what's included.
- cleanups:
. UDC drivers no longer touch gadget->dev, that's now udc-core
responsibility
. Many more UDC drivers converted to usb_gadget_map/unmap_request()
. UDC drivers no longer initialize DMA-related fields from gadget's
device structure
. UDC drivers don't touch gadget.dev.driver directly
. UDC drivers don't assign gadget.dev.release directly
. Removal of some unused DMA_ADDR_INVALID
. Introduction of CONFIG_USB_PHY
. All phy drivers have been moved to drivers/usb/phy and renamed to
a common naming scheme
. Fix PHY layer so it never returns a NULL pointer, also fix all
callers to avoid using IS_ERR_OR_NULL()
. Sparse fixes all over the place
. drivers/usb/otg/ has been deleted
. Marvel drivers (mv_udc, ehci-mv, mv_otg and mv_u3d) improved clock
usage
- new features:
. UDC core now provides a generic way for tracking and reporting
UDC's state (not attached, resuming, suspended, addressed,
default, etc)
. twl4030-usb learned that it shouldn't be enabled during init
. Full DT support for DWC3 has been implemented
. ab8500-usb learned about pinctrl framework
. nop PHY learned about DeviceTree and regulators
. DWC3 learned about suspend/resume
. DWC3 can now be compiled in host-only and gadget-only (as well as
DRD) configurations
. UVC now enables streaming endpoint based on negotiated speed
. isp1301 now implements the PHY API properly
. configfs-based interface for gadget drivers which will lead to
the removal of all code which just combines functions together
to build functional gadget drivers.
. f_serial and f_obex were converted to new configfs interface while
maintaining old interface around.
- non-critical fixes:
. UVC gadget driver got fixes for Endpoint usage and stream calculation
. ab8500-usb fixed unbalanced clock and regulator API usage
. twl4030-usb got a fix for when OMAP3 is booted with cable connected
. fusb300_udc got a fix for DMA usage
. UVC got fixes for two assertions of the USB Video Class Compliance
specification revision 1.1
. build warning issues caused by recent addition of __must_check to
regulator API
These are all changes which deserve a mention, all other changes are related
to these one or minor spelling fixes and other similar tasks.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=aF4r
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.10 merge window
Here is the big Gadget & PHY pull request. Many of us have
been really busy lately getting multiple drivers to a better
position.
Since this pull request is so large, I will divide it in sections
so it's easier to grasp what's included.
- cleanups:
. UDC drivers no longer touch gadget->dev, that's now udc-core
responsibility
. Many more UDC drivers converted to usb_gadget_map/unmap_request()
. UDC drivers no longer initialize DMA-related fields from gadget's
device structure
. UDC drivers don't touch gadget.dev.driver directly
. UDC drivers don't assign gadget.dev.release directly
. Removal of some unused DMA_ADDR_INVALID
. Introduction of CONFIG_USB_PHY
. All phy drivers have been moved to drivers/usb/phy and renamed to
a common naming scheme
. Fix PHY layer so it never returns a NULL pointer, also fix all
callers to avoid using IS_ERR_OR_NULL()
. Sparse fixes all over the place
. drivers/usb/otg/ has been deleted
. Marvel drivers (mv_udc, ehci-mv, mv_otg and mv_u3d) improved clock
usage
- new features:
. UDC core now provides a generic way for tracking and reporting
UDC's state (not attached, resuming, suspended, addressed,
default, etc)
. twl4030-usb learned that it shouldn't be enabled during init
. Full DT support for DWC3 has been implemented
. ab8500-usb learned about pinctrl framework
. nop PHY learned about DeviceTree and regulators
. DWC3 learned about suspend/resume
. DWC3 can now be compiled in host-only and gadget-only (as well as
DRD) configurations
. UVC now enables streaming endpoint based on negotiated speed
. isp1301 now implements the PHY API properly
. configfs-based interface for gadget drivers which will lead to
the removal of all code which just combines functions together
to build functional gadget drivers.
. f_serial and f_obex were converted to new configfs interface while
maintaining old interface around.
- non-critical fixes:
. UVC gadget driver got fixes for Endpoint usage and stream calculation
. ab8500-usb fixed unbalanced clock and regulator API usage
. twl4030-usb got a fix for when OMAP3 is booted with cable connected
. fusb300_udc got a fix for DMA usage
. UVC got fixes for two assertions of the USB Video Class Compliance
specification revision 1.1
. build warning issues caused by recent addition of __must_check to
regulator API
These are all changes which deserve a mention, all other changes are related
to these one or minor spelling fixes and other similar tasks.
Signed-of-by: Felipe Balbi <balbi@ti.com>
In hardware_enqueue code adds one extra td with dma_pool_alloc if
mReq->req.zero is true. When _ep_nuke will be called for that endpoint,
dma_pool_free will not be called to free that memory again. That patch
fixes this.
Cc: stable <stable@vger.kernel.org> # v3.5
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The udc uses an shared dma memory space between hard and software. This
memory layout is described in ci13xxx_qh and ci13xxx_td which are marked
with the attribute ((packed)).
The compiler currently does not know about the alignment of the memory
layout, and will create strb and ldrb operations.
The Datasheet of the synopsys core describes, that some operations on
the mapped memory need to be atomic double word operations. I.e. the
next pointer addressing in the qhead, as otherwise the hardware will
read wrong data and totally stuck.
This is also possible while working with the current active td queue,
and preparing the td->ptr.next in software while the hardware is still
working with the current active td which is supposed to be changed:
writeb(0xde, &td->ptr.next + 0x0); /* strb */
writeb(0xad, &td->ptr.next + 0x1); /* strb */
<----- hardware reads value of td->ptr.next and get stuck!
writeb(0xbe, &td->ptr.next + 0x2); /* strb */
writeb(0xef, &td->ptr.next + 0x3); /* strb */
This appeares on armv5 machines where the hardware does not support
unaligned 32bit operations.
This patch adds the attribute ((aligned(4))) to the structures to tell
the compiler to use 32bit operations. It also adds an wmb() for the
prepared TD data before it gets enqueued into the qhead.
Cc: stable <stable@vger.kernel.org> # v3.5
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A static count of transfer descriptors was used everywhere in the driver
with the fixed number 5. This patch adds a define, named TD_PAGE_COUNT,
and replaces all users of this value. This way its possible to have only
one parameter to change and limit the amount of buffer pointers per TD.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to call ep_queue unlocked inside the own driver. We
move its functionionality into an unlocked version.
This patch removes potential unlocked timeslots inside
isr_setup_status_phase and isr_get_status_response, in which the lock
got released just before acquired again inside usb_ep_queue.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is not safe to truncate requests to the maximum possible size the
controller can handle with one td and to keep working. That patch fixes
that with proper error handling instead.
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch changes the read of the td status to one atomic operation to
analyse coherent bits.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
[Alex: fixed backwards endianness conversion]
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Its not necessary and also not specified in the datasheet to change the
ZLT flag before every ep_prime. This patch moves this to the ep_enable
and applies it only for non configuration endpoints.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch reworks the cap value from several read
and write operations to one single operation.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
[Alex: removed useless isoc-related bit of code]
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The datasheet of the synopsys core describes only to overwrite the
active and halted bits in the qhead before priming any endpoint.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
[Alex: fixed a case of line-too-long]
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert between big-endian and little-endian format when accessing the usb
controller structures which are little-endian by specification.
Fix cases where the little-endian memory layout is taken for granted.
The patch doesn't have any effect on the already supported little-endian
architectures.
Signed-off-by: Svetoslav Neykov <svetoslav@neykov.name>
[Alex: minor cosmetic fixes]
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI chipideas' platform datas are not static as all such things should
be. Fix it.
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds a post handling routine which is called after
ci13xxx_add_device was called. The first user is the mx25, which has to
disable the external-vbus-divider after the udc has started.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
[Alex: also fixed a signed one-bit bitfield a whitespace error and yet
another set of line-too-long and void pointer casting errors]
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds mx53 as the next user of the usbmisc driver and makes it
possible to disable the overcurrent-detection of the internal phy.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
[Alex: fixed another set of line-too-long and void pointer cast]
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This attaches the usbmisc_ops to the of_device_id data and
makes it possible to define special functions per soc.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
[Alex: fixed one case of line-too-long and one bogus cast to void ptr]
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a potential race condition where the ci13xxx_imx glue code
could be fast enough to call one of the usbmisc_ops before he got a
valid value on the static usbmisc pointer. To fix that we first set
usbmisc, then call usbmisc_set_ops().
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe function checks usbmisc to be NULL in the beginning. Without
this patch the can only be loaded once.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver will be used for every Freescale SoC which has this misc
memory layout to control the basic usb handling. So better name this
driver, function and struct names in a more generic way.
Reported-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
chipidea's ffs_nr() is pretty much what __ffs() does.
Use that one instead.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[rebased on top of debug infrastructure rework]
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The intent here was to have parenthesis around the (ci->hw_ep_max / 2)
so that it counts like "0 1 2 0 1 2". In the current code, the mod
operation happens first so it counts like "0 0 1 1 2 2".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[rebased on top of debug.c changes]
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create and remove debugfs entries in hdrc probe/remove instead of
start/stop of the device controller. Gadget specific will not export
anything while the controller is in host mode.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Manual role switching function is there for debugging purposes, so has
to move to debugfs.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, we have a bunch of files in sysfs that display all sorts of
debugging information for the device controller, so they have to move to
debugfs where they belong. The "registers" interface have been removed,
since it doesn't fit into the current driver design as is and it's hardly
a good idea to touch the registers from userspace anyway.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As part of the legacy from the original driver design, we retain home-grown
tracing infrastructure, complete with own ring buffer and timestamps,
which among other things has a performance penalty. This patch removes it.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are several problems with this patch:
+ in introduces a sparse warning for a condition that's always negative,
+ and because of that, it actually doesn't do anything useful,
+ and vbus detection belongs to otg, not device function anyway.
This reverts commit 8c4fc03195.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
[Alex: amended the above text]
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
switch over to the newly added devm_ioremap_resource
which provides more consistent error messages.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some headers included in the chipidea controller core are not needed,
remove them.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some headers included in udc core code are not actually needed, remove
them and add irqreturn.h, which was implicitly included via irq.h.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
debug.c is carrying a lot of includes that aren't needed there, although
they implicitly include the ones that are actually needed. Replace the
former with the latter.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is to pick up the fixes in that branch, and let Alan fix the merge
error in drivers/usb/host/ehci-timer.c better than I just did (as I know
I messed it up...)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't need the ->register_my_device flag
anymore because all UDC drivers have been
properly converted.
Let's remove every history of it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Staticize usbmisc_imx6q_drv_init/exit() to fix the following sparse warnings:
drivers/usb/chipidea/usbmisc_imx6q.c:147:12: warning: symbol 'usbmisc_imx6q_drv_init' was not declared. Should it be static?
drivers/usb/chipidea/usbmisc_imx6q.c:153:13: warning: symbol 'usbmisc_imx6q_drv_exit' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull core locking changes from Ingo Molnar:
"The biggest change is the rwsem lock-steal improvements, both to the
assembly optimized and the spinlock based variants.
The other notable change is the clean up of the seqlock implementation
to be based on the seqcount infrastructure.
The rest is assorted smaller debuggability, cleanup and continued -rt
locking changes."
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rwsem-spinlock: Implement writer lock-stealing for better scalability
futex: Revert "futex: Mark get_robust_list as deprecated"
generic: Use raw local irq variant for generic cmpxchg
lockdep: Selftest: convert spinlock to raw spinlock
seqlock: Use seqcount infrastructure
seqlock: Remove unused functions
ntp: Make ntp_lock raw
intel_idle: Convert i7300_idle_lock to raw_spinlock
locking: Various static lock initializer fixes
lockdep: Print more info when MAX_LOCK_DEPTH is exceeded
rwsem: Implement writer lock-stealing for better scalability
lockdep: Silence warning if CONFIG_LOCKDEP isn't set
watchdog: Use local_clock for get_timestamp()
lockdep: Rename print_unlock_inbalance_bug() to print_unlock_imbalance_bug()
locking/stat: Fix a typo
Here's the big USB merge for 3.9-rc1
Nothing major, lots of gadget fixes, and of course, xhci stuff.
All of this has been in linux-next for a while, with the exception of
the last 3 patches, which were reverts of patches in the tree that
caused problems, they went in yesterday.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZ/kACgkQMUfUDdst+ylEhwCgyM0JEOgLuW7M8D+oNcitZn51
g7oAniD0IkLG8RCB8plLj+82AvthalCo
=bHSs
-----END PGP SIGNATURE-----
Merge tag 'usb-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here's the big USB merge for 3.9-rc1
Nothing major, lots of gadget fixes, and of course, xhci stuff.
All of this has been in linux-next for a while, with the exception of
the last 3 patches, which were reverts of patches in the tree that
caused problems, they went in yesterday."
* tag 'usb-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (190 commits)
Revert "USB: EHCI: make ehci-vt8500 a separate driver"
Revert "USB: EHCI: make ehci-orion a separate driver"
Revert "USB: update host controller Kconfig entries"
USB: update host controller Kconfig entries
USB: EHCI: make ehci-orion a separate driver
USB: EHCI: make ehci-vt8500 a separate driver
USB: usb-storage: unusual_devs update for Super TOP SATA bridge
USB: ehci-omap: Fix autoloading of module
USB: ehci-omap: Don't free gpios that we didn't request
USB: option: add Huawei "ACM" devices using protocol = vendor
USB: serial: fix null-pointer dereferences on disconnect
USB: option: add Yota / Megafon M100-1 4g modem
drivers/usb: add missing GENERIC_HARDIRQS dependencies
USB: storage: properly handle the endian issues of idProduct
testusb: remove all mentions of 'usbfs'
usb: gadget: imx_udc: make it depend on BROKEN
usb: omap_control_usb: fix compile warning
ARM: OMAP: USB: Add phy binding information
ARM: OMAP2: MUSB: Specify omap4 has mailbox
ARM: OMAP: devices: create device for usb part of control module
...
The static lock initializers want to be fed the proper name of the
lock and not some random string. In mainline random strings are
obfuscating the readability of debug output, but for RT they prevent
the spinlock substitution. Fix it up.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Delete successive tests to the same location. In this case res has already
been tested for being NULL, and calling devm_request_and_ioremap will not
make it NULL. On the other hand, devm_request_and_ioremap can return NULL
on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@s exists@
local idexpression y;
expression x,e;
@@
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
... when != \(y = e\|y += e\|y -= e\|y |= e\|y &= e\|y++\|y--\|&y\)
when != \(XT_GETPAGE(...,y)\|WMI_CMD_BUF(...)\)
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When running a scp transfer using a USB/Ethernet adapter the following crash
happens:
$ scp test.tar.gz fabio@192.168.1.100:/home/fabio
fabio@192.168.1.100's password:
test.tar.gz 0% 0 0.0KB/s --:-- ETA
------------[ cut here ]------------
WARNING: at net/sched/sch_generic.c:255 dev_watchdog+0x2cc/0x2f0()
NETDEV WATCHDOG: eth0 (asix): transmit queue 0 timed out
Modules linked in:
Backtrace:
[<80011c94>] (dump_backtrace+0x0/0x10c) from [<804d3a5c>] (dump_stack+0x18/0x1c)
r6:000000ff r5:80412388 r4:80685dc0 r3:80696cc0
[<804d3a44>] (dump_stack+0x0/0x1c) from [<80021868>]
(warn_slowpath_common+0x54/0x6c)
[<80021814>] (warn_slowpath_common+0x0/0x6c) from [<80021924>]
(warn_slowpath_fmt+0x38/0x40)
...
Setting SDIS (Stream Disable Mode- bit 4 of USBMODE register) fixes the problem.
However, in current code CI13XXX_DISABLE_STREAMING flag is only set in udc mode,
so allow disabling streaming also in host mode.
Tested on a mx6qsabrelite board.
Suggested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pointer to a platform_device struct must not be dereferenced after
the device has been unregistered.
This bug produces a crash when unloading the ci13xxx kernel module
compiled with CONFIG_PAGE_POISONING enabled.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Cc: stable <stable@vger.kernel.org> # 3.6
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinitdata is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Olav Kongas <ok@artecdesign.ee>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1630) cleans up a few minor items resulting from the
split-up of the ehci-hcd driver:
Remove the product_desc string from the ehci_driver_overrides
structure. All drivers will use the generic "EHCI Host
Controller" string. (This was requested by Felipe Balbi.)
Allow drivers to pass a NULL pointer to ehci_init_driver()
if they don't have to override any settings.
Remove a #define symbol that is no longer used from the
ChipIdea host driver.
Rename overrides to pci_overrides in ehci-pci.c, for
consistency with ehci-platform.c.
Mark the *_overrides structures as __initdata.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
renesas_usbhs implements ->pullup() method, switches over
to devm_request_irq(), adds support for DMA Engine and
got a few miscelaneous cleanups.
The NCM gadget got an endianness fix and the Ethernet
gadget a frame size fix.
We're finally removing the g_file_storage gadget and
sticking to g_mass_storage and the new tcm_usb_gadget
gadgets since that was a huge duplicaton of effort anyway.
While removing g_file_storage, we also had to fix a bunch
of defconfigs which were still pointing to the old gadget.
There's a big series getting us closer to being able to
introduce our configfs interface. The series converts
functions into loadable modules which will, eventually,
be registered to the configfs interface.
Other than that there's the usual typo fixes and miscelaneous
cleanups all over the place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=umtl
-----END PGP SIGNATURE-----
Merge tag 'gadget-for-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
USB gadget patches from Felipe:
"usb: gadget: patches for v3.8
renesas_usbhs implements ->pullup() method, switches over
to devm_request_irq(), adds support for DMA Engine and
got a few miscelaneous cleanups.
The NCM gadget got an endianness fix and the Ethernet
gadget a frame size fix.
We're finally removing the g_file_storage gadget and
sticking to g_mass_storage and the new tcm_usb_gadget
gadgets since that was a huge duplicaton of effort anyway.
While removing g_file_storage, we also had to fix a bunch
of defconfigs which were still pointing to the old gadget.
There's a big series getting us closer to being able to
introduce our configfs interface. The series converts
functions into loadable modules which will, eventually,
be registered to the configfs interface.
Other than that there's the usual typo fixes and miscelaneous
cleanups all over the place."
This commit removes the /sys/devices/platform/<UDC>/udc/<UDC>/is_dualspeed
file and is_dualspeeed line from /sys/devices/platform/ci13xxx_*/udc/device
file.
The is_dualspeed file is superseded by maximum_speed in the same directory
and is_dualspeed line in device file is superseded by max_speed line in
the same file.
The maximum_speed/max_speed specifies maximum speed supported by UDC.
To check if dualspeeed is supported, check if the value is >= 3.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch (as1629) fixes a build error in the ChipIdea host driver
when compiled for the ARM architecture. The error was introduced
by commit 99f91934a9 (USB: EHCI: make
ehci-platform a separate driver).
The fix is simple; an additional header-file #include is needed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1627) splits the ehci-hcd core code, which has become a
separate library module, out from the ChipIdea host driver. Instead
of #include-ing ehci-hcd.c directly, the ChipIdea module will now use
the ehci-hcd library in a normal fashion.
This fixes a build error caused by commit
3e02320399 (USB: EHCI: prepare to make
ehci-hcd a library module); I had forgotten about the unorthodox way
the ChipIdea driver uses the ehci-hcd code.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1623) removes the ehci_port_power() routine and all the
places that call it. There's no reason for ehci-hcd to change the
port power settings; the hub driver takes care of all that stuff.
There is one exception: When the controller is resumed from
hibernation or following a loss of power, the ports that are supposed
to be handed over to a companion controller must be powered on first.
Otherwise the handover won't work. This process is not visible to the
hub driver, so it has to be handled in ehci-hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- let role driver handle irq before ID change check; this gives the
role driver a chance to handle disconnect;
- disable irq during switch role; no role driver to handle irq in
the period.
Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch turns on debugging output if CONFIG_USB_CHIPIDEA_DEBUG is
enabled.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using vbus valid interrupt to detect vbus.
Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to avoid re-queueing of the role changing work, we need to clear
the ID change interrupt bit right in the irq handler.
Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ID pin needs 1ms debounce time, even at probe time. We delay 2ms
to be on the safe side.
Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some controllers may not need to setup pinctrl, so we don't fail the
probe if pinctrl get/select failed.
Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i.MX usb controllers share non-core registers, which may include
SoC specific controls. We turn it into a usbmisc device and usbmisc
driver set operations needed by ci13xxx_imx driver.
For example, Sabrelite board has bad over-current design, we can
usbmisc to disable over-current detection.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These chipidea stable patches are needed for other chipidea patches to be
applied properly.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When attaching an imx28 or imx53 in USB gadget mode to a Windows host and
starting a rndis connection we see this message every 4-10 seconds:
g_ether gadget: high speed config #2: RNDIS
Analysis shows that each time this message is printed, the rndis connection is
re-establish due to a reset because of a stalled endpoint (ep 0, dir 1). The
endpoint is stalled because the reqeust complete bit on that endpoint is set,
but in isr_tr_complete_low() the endpoint request list (mEp->qh.queue) is
empty.
This patch removed this check, because the code doesn't take the following
situation into account:
The loop over all endpoints in isr_tr_complete_handler() will call ep_nuke() on
both ep0/dir0 and ep/dir1 in the first loop. Pending reqeusts will be flushed
and completed here. There seems to be a race condition, the request is nuked,
but the request complete bit will be set, too. The subsequent check (in
ep0/dir1's loop cycle) for endpoint request list (mEp->qh.queue) empty will
fail.
Both other mainline chipidea drivers (mv_udc_core.c and fsl_udc_core.c) don't
have this check.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If udc_start() fails the qh_pool dma-pool cannot be closed because
it's still in use. This patch factors out the dma_pool_free() loop
into destroy_eps() and calls it in the error path of udc_start(),
too.
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the error path of udc_start(). Now NULL is used to
unset the peripheral with otg_set_peripheral().
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add function to physicaly enable or disable of pullup connection on the USB-D+
line. The uvc gaget will fail, if this function is not implemented.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch changes the setup of the endpoint maxpacket size. All non control
endpoints are initialized with an undefined ((unsigned short)~0) maxpacket
size. The maxpacket size of Endpoint 0 will be kept at CTRL_PAYLOAD_MAX.
Some gadget drivers check for the maxpacket size before they enable the
endpoint, which leads to a wrong state in these drivers.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This pull request is large but the biggest part is the first part
of the cleanup on the gadget framework so we have a saner setup
to add configfs support for v3.8.
We have also some more conversions to the new udc_start/udc_stop
which makes us closer from dropping the old interfaces.
USB_GADGET_DUALSPEED and USB_GADGET_SUPERSPEED are finally gone,
thanks to Michal for his awesome work.
Other than that, we have the usual set of miscellaneous changes
and cleanups involving improvements to debug messages, removal
of duplicated includes, moving dereference after NULL test,
making renesas_hsbhs' irq handler Shared, unused code being dropped,
prevention of sleep-inside-spinlock bugs and a race condition fix
on udc-core.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=T3kf
-----END PGP SIGNATURE-----
Merge tag 'gadget-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: gadget: patches for v3.7 merge window
This pull request is large but the biggest part is the first part
of the cleanup on the gadget framework so we have a saner setup
to add configfs support for v3.8.
We have also some more conversions to the new udc_start/udc_stop
which makes us closer from dropping the old interfaces.
USB_GADGET_DUALSPEED and USB_GADGET_SUPERSPEED are finally gone,
thanks to Michal for his awesome work.
Other than that, we have the usual set of miscellaneous changes
and cleanups involving improvements to debug messages, removal
of duplicated includes, moving dereference after NULL test,
making renesas_hsbhs' irq handler Shared, unused code being dropped,
prevention of sleep-inside-spinlock bugs and a race condition fix
on udc-core.
This commit removes USB_GADGET_DUALSPEED and USB_GADGET_SUPERSPEED
Kconfig options. Since now kernel allows many UDC drivers to be
compiled, those options may turn to no longer be valid. For
instance, if someone decides to build UDC that supports super
speed and UDC that supports high speed only, the latter will be
"assumed" to support super speed since USB_GADGET_SUPERSPEED will
be selected by the former.
The test of whether CONFIG_USB_GADGET_*SPEED was defined was just
an optimisation which removed otherwise dead code (ie. if UDC is
not dual speed, there is no need to handle cases that can happen
if speed is high). This commit removes those checks.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since commit "5e0aa49 usb: chipidea: use generic map/unmap routines",
the udc part of the chipidea driver needs the generic usb gadget helper
functions. If the chipidea driver with udc support is built into the
kernel and usb gadget is built a module, the linking of the kernel
fails with:
drivers/built-in.o: In function `_hardware_dequeue':
drivers/usb/chipidea/udc.c:527:
undefined reference to `usb_gadget_unmap_request'
drivers/usb/chipidea/udc.c:1269:
undefined reference to `usb_gadget_unmap_request'
drivers/usb/chipidea/udc.c:1821:
undefined reference to `usb_del_gadget_udc'
drivers/usb/chipidea/udc.c:443:
undefined reference to `usb_gadget_map_request'
drivers/usb/chipidea/udc.c:1774:
undefined reference to `usb_add_gadget_udc'
This patch changes the dependencies, so that udc support can only be
activated if the linux gadget support (USB_GADGET) is builtin or both
chipidea driver and USB_GADGET are modular. Same dependencies for the
chipidea host support and the linux host side USB support (USB).
While there, fix the indention of chipidea the help text.
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch supports only the host-mode functionality so far.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peter Chen <peter.chen@freescale.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Tested-by: Subodh Nijsure <snijsure@grid-net.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes, the driver bindings may know what phy they use.
For example, when using device tree, the usb controller may have a
phandler pointing to usb phy.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Subodh Nijsure <snijsure@grid-net.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We use ida_simple_get and ida_simple_remove to manage the ids.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Platform drivers do the similar things to add/remove ci13xxx device, so
create a unified one.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct ci13xxx represent the controller, which may be device or host,
so name its variables as ci.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch rename struct ci13xxx_udc_driver and var with the type.
ci13xxx_platform_data reflect it's passed from platfrom driver.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
allow this driver to be removed too.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No functional changes, it will just free up some
code if we don't have hotplug.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
msm glue layer compiles on all arches just
fine. Let's drop the unnecessary ARCH check
so we have easier compile tests.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As reported by Dan Carpenter, there is a NULL check in udc_start() that
follows a dereference of the pointer that's being checked. However, at
that point udc pointer shouldn't ever be NULL and if it is, the dereference
should cause an oops.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_get_phy will return -ENODEV if it's not able to find the phy. Hence
fixed all the callers of usb_get_phy to check for this error condition
instead of relying on a non-zero value as success condition.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add a linked list for keeping multiple PHY instances with different
types so that we can have separate USB2 and USB3 PHYs on one single
board. _get_phy_ has been changed so that the controller gets
the transceiver by type. _remove_phy_ has been added to let the phy
be removed from the phy list.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
_transceiver() in otg.c is replaced with _phy. usb_set_transceiver is
replaced with usb_add_phy to make it similar to other usb standard
function names like usb_add_hcd.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It's 0 for host only device.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use usb_put_hcd() call instead of usb_remove_hcd() as that's the appropriate
call to drop hcd which failed registration.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was used as a shorthand for gadget's device in request mapping/unmapping
code, but now it's not used any more.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We're one of the remaining drivers to map/unmap requests by hand. Switch
to using generic gadget routines for that instead.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some implementations need this limitation to work correctly.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds EHCI host support to the chipidea driver. We want it to be
part of the hdrc driver and not a standalone (sub-)driver module, as
the structure of ehci-hcd.c suggests, so for chipidea controller we
hack it to not provide platform-related code, but only the ehci hcd.
The ehci-platform driver won't work for us here too, because the
controller uses the same registers for both device and host mode and
also otg-related bits, so it's not really possible to put ehci registers
into a separate resource.
This is not a pretty solution, but the alternative is exporting symbols
from the chipidea driver to a ehci-chipidea driver and doing all the
module refcounting.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the bits of USBMODE register are defined in <usb/ehci_def.h>,
use them instead of having our own definitions.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These definitions are unused, and the same registers are also defined
in <linux/usb/msm_hsusb_hw.h>.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, gadget can't be NULL in _gadget_stop_activity().
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Reported-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move spin_lock under the done label, so the
lock will also be pulled in the error paths.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
[rebased on top of the patchset]
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get rid of trailing comments in the structure definitions in favor of
kernel-doc.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The old implementation used global hw_bank, the new implementation uses
udc-local hw_bank. This field seems to be a leftover from previous coding
experiments.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add some generic code for roles and implement simple role switching
based on ID pin state and/or a sysfs file. At this, we also rename
the device to ci_hdrc, which is what it is.
The "manual" switch is made into a sysfs file and not debugfs, because
it might be useful even in non-debug context. For some boards, like
sheevaplug, it seems to be the only way to switch roles without modifying
the hardware, since the ID pin is always grounded.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since chipidea is a dual role controller, it makes sense to move it
to its own directory, where we can also have host, otg and platform
code related to this controller. It also makes sense to break out
the driver into several compilation units like udc, host, debugging
code, etc.
Firstly, let's move the udc and platform code to drivers/usb/chipidea.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
