This makes the function hw_alloc_repmap be declared to have a return
type of void now due to this particular function never returning
a error code to its caller due to this function always running
successfully to completion nor it's caller putting the return
value into a variable in order to check if a error code is passed
from the function hw_alloc_repmap when calling this function.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
The struct ci_hdrc is the drvdata for hcd device, so we don't
need to introduce extra ci_hdrc structure for ehci.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
ITC (Interrupt Threshold Control) is used to set the maximum rate at which
the host/device controller will issue interrupts. The default value is 8 (1ms)
for it. EHCI core will modify it to 1, but device mode keeps it as default
value.
In some use cases like Android ADB, it only has one usb request for each
direction, and maximum payload data is only 4KB, so the speed is 4MB/s
at most, it needs controller to trigger interrupt as fast as possible
to increase the speed. The USB performance will be better if the interrupt
can be triggered faster.
Reduce ITC value is benefit for USB performance, but the interrupt number
is increased at the same time, it may increase cpu utilization too.
Most of use case cares about performance, but some may care about
cpu utilization, so, we leave a platform interface for user.
We set ITC as 1 (1 micro-frame) as default value which is aligned
with ehci core default value.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
It is used to configure controller parameters according to
platform data, like speed, stream mode, etc, both host and
device's initialization need it, most of code are the
same for both roles, with this new interface, it can reduce
the duplicated code and be easy to maintain in future.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
We can support USB OTG 1.3 USB_DEVICE_A_HNP_SUPPORT request when
the driver supports OTG FSM mode.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
For i.mx platform, set ttctrl.ttha with non-zero value only affects
sitd, and ehci core makes sure the schedule is not full when accepts
new request, so it will not occur the transaction which will acorss
the SoF.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
The register of ttctrl.ttha describes like below:
- Internal TT Hub Address Representation
- RW
- Default = 0000000b
This field is used to match against the Hub Address field in QH & siTD
to determine if the packet is routed to the internal TT for directly
attached FS/LS devices. If the Hub Address in the QH or siTD does not
match this address then the packet will be broadcast on the High Speed
ports destined for a downstream High Speed hub with the address in the QH/siTD.
In silicon RTL, this entry only affects QH and siTD, and the hub.addr at
both QH and siTD are 0 in ehci core for chipidea (with hcd->has_tt = 1).
So, for QH, if the "usage_tt" flag at RTL is 0, set CI_HDRC_SET_NON_ZERO_TTHA
will not affect QH (with non-hs device); for siTD, set this flag
will change remaining space requirement for the last transaction from 1023
bytes to 188 bytes, it can increase the number of transactions within one
frame, ehci periodic schedule code will not queue the packet if the frame space
is full, so it is safe to set this flag for siTD.
With this flag, it can fix the problem Alan Stern reported below:
http://www.spinics.net/lists/linux-usb/msg123125.html
And may fix Michael Tessier's problem too.
http://www.spinics.net/lists/linux-usb/msg118679.html
CC: stern@rowland.harvard.edu
CC: michael.tessier@axiontech.ca
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Just a minor change for code style
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVdQexAAoJEEhZKYFQ1nG7/M0H/3gZcnjvF2nN6NYBUhFpz33r
BAIDYumRhAPOVbnmXYZOh24+yPEhKYTWaZycjQeJXBVd23r8EFGP4Vl+K6vCTtJX
jIQZ+73ntPwDBgvDfPN1Lk+Kj2G3dPl6b+ZmmAj1lS1ea2ewDR5Q+OM3/bX6kscN
zccMIMv/++jLOvAeOvoa5Hk7JZdQK+DQaSCLRZAfEfID40I0A7j6OcWP3B8qebGD
faYc9XfA+Li/C1q7qvUFWTWHcVkQT56syffLXetts3sOuo7EzPlyyBT6zreKi//a
MHWv+VBkoQvqDYej7fLqfpRBy221beEfFXH5DAcDRr7q1ikKUIPWxiqwUOnJ4P0=
=Yq7y
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-work
Peter writes:
USB Chipidea update for v4.2-rc1
Just a minor change for code style
The Marvell 28nm HSIC PHY requires the port to be forced to HS mode after
the port power is applied. This is done using the test mode in the PORTSC
register.
As HSIC is always HS, this work-around should be safe to do with all HSIC
PHYs and has been tested on i.MX6S.
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Peter Chen <Peter.Chen@freescale.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, ci_default_pdata is common to all instances of the driver and
gets modified by the core driver code. This is bad if there are multiple
instances of the device with different settings such as the phy type. Fix
this by making a copy of the default platform_data.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Peter Chen <Peter.Chen@freescale.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unneeded semicolon.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/semicolon.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
A string written by the user may not be zero terminated.
sscanf may read memory beyond the buffer if no zero byte
is found.
For testing build with CONFIG_USB_CHIPIDEA=y, CONFIG_USB_CHIPIDEA_DEBUG=y.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Wrongly release mutex lock during otg_statemachine may result in re-enter
otg_statemachine, which is not allowed, we should do next state transtition
after previous one completed.
Fixes: 826cfe751f ("usb: chipidea: add OTG fsm operation functions implementation")
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the required clock to access registers is gated off in low power mode,
add ci->in_lpm check before try to dump registers value.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
By pass pullup DP in OTG fsm mode when do gadget connect, to let it handled
by OTG state machine.
This patch can fix the problem you found with my HNP polling patchset after
below 3 patches introduced:
467a78c usb: chipidea: udc: apply new usb_udc_vbus_handler interface
628ef0d usb: udc: add usb_udc_vbus_handler
dfea9c9 usb: udc: store usb_udc pointer in struct usb_gadget
Problem:
- Connect USB cable and MicroAB cable between two boards
- Boot up two boards
- load g_mass_storage at B-device side, the enumeration will success,
and A will see a usb mass-storage device
- load g_mass_storage at A-device side, the problem has occurred, the
connection will be lost at the beginning, then connect again.
This patch is based on
commit eff933c1d3a2e046492b3dfc86db813856553a29
(chipidea: pci: make it depends on NOP_USB_XCEIV)
on branch peter-usb-dev of
git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb.git
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
After commit ba1aff67f9 (chipidea: pci: register nop PHY) the PCI glue driver
requires nop-PHY to be selected. Thus, make it an explicit dependency.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: ba1aff67f9 (chipidea: pci: register nop PHY)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces USB_CHIPIDEA_PCI and USB_CHIPIDEA_OF Kconfig options, one
per each specific glue driver. This is needed to provide different dependencies
they have.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current otg fsm timers are using controller 1ms irq and count it, this patch
is to replace it with hrtimer solution, use one hrtimer for all otg timers.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
B_DATA_PLS(data-line pulse time) and B_SSEND_SRP(session end to SRP init) are
also from OTG&EH 2.0 Specification and they are not chipidea specific.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since BSV irq is enabled for B-device all the time, so B_SESS_VLD timer
is not required, and also no need to check BSV status when B_ASE0_BRST
timer timeout.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As usual, a big pile of commits. This time a total
of 111 non-merge commits.
Other than the usual set of cleanups and non-critical
fixes, we have some interesting work for AM335x's MUSB
babble recovery. Now that takes a lot less time and we
don't have to Reset MUSB all the time.
The printer gadget has been converted to configfs interface
and the atmel udc has learned suspend/resume with wakeup.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=U+M2
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.1 merge window
As usual, a big pile of commits. This time a total
of 111 non-merge commits.
Other than the usual set of cleanups and non-critical
fixes, we have some interesting work for AM335x's MUSB
babble recovery. Now that takes a lot less time and we
don't have to Reset MUSB all the time.
The printer gadget has been converted to configfs interface
and the atmel udc has learned suspend/resume with wakeup.
Signed-off-by: Felipe Balbi <balbi@ti.com>
It can move all pullup/pulldown operation control to udc-core
through usb_gadget_connect/usb_gadget_disconnect according to
vbus status.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds runtime power management support for otg fsm mode, since
A-device in a_idle state cannot detect data pulse irq after suspended, here
enable wakeup by connection before suspend to make it can be resumed by DP;
and handle wakeup from that state like SRP.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CI_HDRC_TURN_VBUS_EARLY_ON is set, turn on vbus before adding hcd, so it
will not set reg_vbus of ehci_ci_priv, then vbus will not be handled by ehci core.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some usb PHYs need power supply from vbus to make it work, eg mxs-phy, if
there is no vbus, USB PHY will not in correct state when the controller starts
to work, for host, this requires vbus should be turned on before setting port
power(PP) of ehci, to work with this kind of USB PHY design, this patch adds
a flag CI_HDRC_TURN_VBUS_EARLY_ON, can be checked by host driver to turn on
vbus while start host.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since PHY for ChipIdea is optional (not all SoCs having PHY for ChipIdea should
be programmed), we register 'nop' PHY for platforms that do not have
programmable PHY.
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For chipidea, its resume sequence is not-EHCI compatible, see
below description for FPR at portsc. So in order to send SoF in
time for remote wakeup sequence(within 3ms), the RUN/STOP bit must
be set before the resume signal is ended, but the usb resume
code may run after resume signal is ended, so we had to set it
at suspend path.
Force Port Resume - RW. Default = 0b.
1= Resume detected/driven on port.
0=No resume (K-state) detected/driven on port.
Host mode:
Software sets this bit to one to drive resume signaling. The Controller sets this bit to '1' if
a J-to-K transition is detected while the port is in the Suspend state. When this bit
transitions to a '1' because a J-to-K transition is detected, the Port Change Detect bit in
the USBSTS register is also set to '1'. This bit will automatically change to '0' after the
resume sequence is complete. This behavior is different from EHCI where the controller
driver is required to set this bit to a '0' after the resume duration is timed in the driver.
Note that when the controller owns the port, the resume sequence follows the defined
sequence documented in the USB Specification Revision 2.0. The resume signaling
(Full-speed 'K') is driven on the port as long as this bit remains a '1'. This bit will remain
a '1' until the port has switched to idle. Writing a '0' has no affect because the port
controller will time the resume operation, clear the bit and the port control state switches
to HS or FS idle.
This field is '0' if Port Power(PP) is '0' in host mode.
This bit is not-EHCI compatible.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PORTSC_PFSC is not set on entering host mode which means the USB OTG
controller will attempt to enumerate USB devices at high speed even when the
CI_HDRC_FORCE_FULLSPEED flag is set in the platform data.
This patch ensures it is set right before host mode operations begin if needed.
Signed-off-by: Daniel Tang <dt.tangr@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At chipidea revision 2.40a, there is a below errata:
9000531823 B2-Medium Adding a dTD to a Primed Endpoint May Not Get Recognized
Title: Adding a dTD to a Primed Endpoint May Not Get Recognized
Impacted Configuration: All device mode configurations.
Description:
There is an issue with the add dTD tripwire semaphore (ATDTW bit in USBCMD register)
that can cause the controller to ignore a dTD that is added to a primed endpoint.
When this happens, the software can read the tripwire bit and the status bit at '1'
even though the endpoint is unprimed.
After executing a dTD, the device controller endpoint state machine executes a final
read of the dTD terminate bit to check if the application added a dTD to the linked
list at the last moment. This read is done in the finpkt_read_latest_next_td (44) state.
After the read is performed, if the terminate bit is still set, the state machine moves
to unprime the endpoint. The decision to unprime the endpoint is done in the
checkqh_decision (59) state, based on the value of the terminate bit.
Before reaching the checkqh_decision state, the state machine traverses the
writeqhtd_status (57), writeqh_status (56), and release_prime_mask (42) states.
As shown in the waveform, the ep_addtd_tripwire_clr signal is not set to clear
the tripwire bit in these states.
Workaround:
The software must implement a periodic poll cycle, and check for each dTD
pending on execution (Active = 1), if the enpoint is primed. It can do this by reading
the corresponding bits in the ENDPTPRIME and ENDPTSTAT registers. If these bits are
read at 0, the software needs to re-prime the endpoint by writing 1 to the corresponding
bit in the ENDPTPRIME register. This can be done for every microframe, every frame or
with a larger interval, depending on the urgency of transfer execution for the application.
Tested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Define ci_get_revision API to know the controller revision
information according to chipidea 1.1a, 2.0a and 2.5a spec.
Besides, add one entry at struct ci_hdrc to indicate revision
information, it can be used for adding different code for
revisions, eg kinds of errata.
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using hw_write_id_reg and hw_read_id_reg to write and read identification
registers contents, they can be used to get controller information, change
some system configurations, and so on.
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Except the same process with earlier imx6, it has below two features:
- Choose which vbus voltage as vbus wakeup source
We choose B_SESSION_VALID as vbus wakeup source since when the system
goes to suspend, the vbus comparator can't compare the vbus voltage
for VBUS_VALID.
- Disable dp/dm (linestate) change as wakeup source at device mode
when the vbus is not there, we don't expect dp/dm change waking up
usb controller at this situation.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to do it for all otg capable controller, not only peripheral
featured otg capable controller, otherwise, the host-only role, but
otg capable controller may be responded by otg interrupt.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable USB as system wakeup source, and each platform needs to implement
imx_usbmisc_set_wakeup in usbmisc_imx.c to support.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB signal can be system wakeup source, this patch add the
support, for how to enable it, see Documentation/usb/chipidea.txt.
Since USB wakeup enable logic is vendor/platform specific, the
glue layer needs to implement it to support this feature.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add runtime pm support for imx, only imx6 series are supported and tested.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This API is used to enable/disable usb wakeup, only imx6 series are
added, since I don't have other imx hardware on hand. Other imx users
can add their API according to reference manual after testing.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move struct imx_usbmisc_data NULL pointer judgement from caller to
each API, it can simplify the caller.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All imx usb controller's non core registers uses the same clock gate with
core registers, the usbmisc_imx is the library for imx glue driver, the
glue keeps clock on when it calls usbmisc_imx API to change non-core register.
Besides, we will support runtime pm in the future, it also needs to
close this clock when the usb is not in use.
Philipp Zabel also verifies it at imx6q platform, see
http://www.spinics.net/lists/linux-usb/msg118491.html
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is meaningless the glue layer driver has its own platform flag
which is the same meaning with common platform flag.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some gadget driver (like uac1) will try to enable endpoint again even
the ep is not empty, it will cause the ep reset again and may affect
the dTD list which has already queued.
It returns -EBUSY immediately, and indicate the endpoint is in use.
In this way, the ep's behavior will not be affected, and the gadget
driver is also notified.
Cc: Xuebing Wang <xbing6@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds response to a_alt_hnp_support set feature request from legacy
A device, that is, B-device can provide a message to the user indicating that
the user needs to connect the B-device to an alternate port on the A-device.
A device sets this feature indicates to the B-device that it is connected
to an A-device port that is not capable of HNP, but that the A-device does have
an alternate port that is capable of HNP.
[Peter]
Without this patch, the OTG B device can't be enumerated on
non-HNP port at A device, see below log:
[ 2.287464] usb 1-1: Dual-Role OTG device on non-HNP port
[ 2.293105] usb 1-1: can't set HNP mode: -32
[ 2.417422] usb 1-1: new high-speed USB device number 4 using ci_hdrc
[ 2.460635] usb 1-1: Dual-Role OTG device on non-HNP port
[ 2.466424] usb 1-1: can't set HNP mode: -32
[ 2.587464] usb 1-1: new high-speed USB device number 5 using ci_hdrc
[ 2.630649] usb 1-1: Dual-Role OTG device on non-HNP port
[ 2.636436] usb 1-1: can't set HNP mode: -32
[ 2.641003] usb usb1-port1: unable to enumerate USB device
Cc: stable <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big pull request for Gadgets and PHYs. It's
a total of 217 non-merge commits with pretty much everything
being touched.
The most important bits are a ton of new documentation for
almost all usb gadget functions, a new isp1760 UDC driver,
several improvements to the old net2280 UDC driver, and
some minor tracepoint improvements to dwc3.
Other than that, a big list of minor cleanups, smaller bugfixes
and new features all over the place.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bGMq
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.20 merge window
Here's the big pull request for Gadgets and PHYs. It's
a total of 217 non-merge commits with pretty much everything
being touched.
The most important bits are a ton of new documentation for
almost all usb gadget functions, a new isp1760 UDC driver,
several improvements to the old net2280 UDC driver, and
some minor tracepoint improvements to dwc3.
Other than that, a big list of minor cleanups, smaller bugfixes
and new features all over the place.
Signed-off-by: Felipe Balbi <balbi@ti.com>
