On HSW enabling a plane on a disabled pipe may hang the entire system.
And there's no good reason for doing it ever, so just don't.
v2: Move the crtc active checks to intel_crtc_cursor_{set,move} to
avoid confusing people during modeset
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The cursor is disabled before crtc mode set in crtc disable (and we
assert this is the case), and enabled afterwards in crtc enable. Do not
update it in crtc mode set.
On HSW enabling a plane on a disabled pipe may hang the entire system.
And there's no good reason for doing it ever, so just don't.
v2: Add note about HSW hangs - vsyrjala
Cc: stable@vger.kernel.org
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Sometimes I see the "non asle set request??" message on my Haswell
machine, so I decided to get the spec and see if some bits are missing
from the mask. We do have some bits missing from the mask, so this
patch adds them, and the corresponding code to print "unsupported"
messages just like we do with the other bits we don't support.
But I still see the "non asle set request??" message on my machine :(
Also use the proper ASLC name to indicate the registers we're talking
about.
v2: - Properly set the new FAILED bits
- Rename the old FAILED bits
- Print everything we don't support
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reduces dmesg noise when there's a glitch on the hpd line, or there
are more than one connectors on the same hpd line and only one of them
changes.
While at it, switch to use the friendly status names instead of numbers.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So far we control everything and nothing exceeds the current limits,
but (i) we never think about these limits when reviewing patches, (ii)
not all the callers check the return values and (iii) if we ever hit
any of these messages, we'll have to fix the code that added the bad
message.
The current limit for these messages is 20 since we only have 5 data
registers on all the current gens.
The checks inside intel_dp_aux_native_{write,read} are to prevent
buffer overflows. The check inside intel_dp_aux_ch is to prevent
writing past our 5 data registers.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Double wide mode is only available on pipe A, except on GDG where
pipe B is also double wide capable.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pipe horizontal source size must be even when either LVDS dual channel
mode, DVO ganged mode, or pipe double wide mode is used.
We must round it down since we can never increase the user specified
viewport size.
The actual error from an odd pipe source width looks like a diagonal
shift, like you might get from a bad stride.
v2: s/ganaged/ganged/
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't want to try to push the hardware beyond it's capabilities,
so check the pixel clock against the display core clock limit. Do
it for pre-gen4 for now since that's where we alread have the double
wide pixel clock limit check.
Let's assume that when double wide mode is enabled the max
pixel clock limit is also doubled.
FIXME: panel fitter downscaling probably affects the limit on
non-pch platforms too, so we'd need another version of
ilk_pipe_pixel_rate() to figure that out.
FIXME: should check the limits on all platforms. Also sprites
affect the max allowed pixel rate on some platforms, so we need
to eventually tie all the planes and pipes into one check in
the future. But we need plane state pre-compute before that can
happen.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Read the double wide pipe information from hardware in
i9xx_get_pipe_config(), and check it in intel_pipe_config_compare()
For gen4+ double_wide is always false so the comparison can be done
on all platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Determine the need for double wide mode already in compute_config
stage as we need that information to figure out if horizontal
coordinates need to be adjusted.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Simply inline the 100MHz default we're using. Having gunk around that
has leftover LVDS support on a platform that just doesn't have this
isn't of any use.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
First of all we should not be looking at fb->{width,height} as those do
not tell us what the actual pipe size is. Second of all we need to use
>= for the comparison.
So fix the comparison, and make use of the new pipe_src_{w,h} to
determine the real pipe source dimensions.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When the cursor x coordinate is exactly -cursor_width, the cursor is
invisible. And obviously the same holds for the y coordinate and
cursor_height.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Try to clarify the purpose of requested_mode.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Especially intel_gmch_panel_fitting was shifting way too much over the
right edge and also was way too long. So extract two helpers, one for
gen4+ and one for gen2/3. Now the entire thing is again almost
readable ...
Spurred by checkpatch freaking out about a Ville's pipeconfig rework
in intel_panel.c
Otherwise just two lines that needed appropriate breaking.
Not functional change in this patch.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rather that mess about with hdisplay/vdisplay from requested_mode, add
explicit pipe src size information to pipe config.
Now requested_mode is only really relevant for dvo/sdvo output timings.
For everything else either adjusted_mode or pipe src size should be
used.
In many places where we end up using pipe source size, we should
actually use the primary plane size, but we don't currently store
that information explicitly. As long as we treat primaries as full
screen only, we can get away with this. Eventually when we move
primaries over to drm_plane, we need to fix it all up.
v2: Add a comment to explain what pipe_src_{w,h} are
Add a note about primary planes to commit message
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
adjusted_mode contains our real timings, not requested_mode. Use the
correct thing in DSI PLL code.
Also constify adjusted_mode since we don't change it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rather than dig up the pipe source size from crtc->mode, use
intel_crtc->config.requested_mode.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move intel_crtc_active() to intel_display.c and make it available
elsewhere as well.
intel_edp_psr_match_conditions() already has one open coded copy,
so replace that one with a call to intel_crtc_active().
v2: Copy paste a big comment from danvet's mail explaining
when we can ditch the extra checks
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_edp_psr_match_conditions() currently looks at crtc->mode
when it really needs to look at adjusted_mode. Fix it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The clock in crtc->mode doesn't necessarily mean anything. Let's look
at the clock in adjusted_mode instead.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently most of the watermark code looks at crtc->mode which is the
user requested mode. The only piece of information there that is
relevant is hdisplay, the rest must come from adjusted_mode. Convert
all of the code to use requested_mode and adjusted_mode from
pipe config appropriately.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Check the mode flags from the adjusted_mode, not user requested mode.
The hdisplay/vdisplay check actually checkes the primary plane size,
so those still need to come from the user requested mode.
Extract both modes from pipe config instead of the drm_crtc.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The pixel clock should come from adjusted_mode not requested_mode.
In this case the two should be the same as we don't currently
overwrite the clock in the case of HDMI. But let's make the code
safe against such things happening in the future.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
lpt_program_iclkip() wants to know the pixel clock. It should get that
information from adjusted_mode, not crtc->mode.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
i9xx_set_pipeconf() attempts to get the current pixel clock from
requested_mode. requested_mode.clock may be totally bogus, so the
clock should come from adjusted_mode.
v2: Dropped the intel_compute_config() hunk due to killing of the
INTEL_FDI_FREQ check
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Check and dump for port_clock.
v2: Also dump port_clock
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a new pipe config check macro PIPE_CONF_CHECK_CLOCK_FUZZY() to make
it trivial and error proof to compare clocks in a fuzzy manner.
v2: Drop extra curly braces
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that adjusted_mode.clock no longer contains the pixel_multiplier, we
can kill the get_clock() callback and instead do the clock readout
in get_pipe_config().
Also i9xx_crtc_clock_get() can now extract the frequency of the PCH
DPLL, so use it to populate port_clock accurately for PCH encoders.
For DP in port A the encoder is still responsible for filling in
port_clock. The FDI adjusted_mode.clock extraction is kept in place
for some extra sanity checking, but we no longer need to pretend it's
also the port_clock.
In the encoder get_config() functions fill out adjusted_mode.clock
based on port_clock and other details such as the DP M/N values,
HDMI 12bpc and SDVO pixel_multiplier. For PCH encoders we will then
do an extra sanity check to make sure the dotclock we derived from
the FDI configuratiuon matches the one we derive from port_clock.
DVO doesn't exist on PCH platforms, so it doesn't need to anything
but assign adjusted_mode.clock=port_clock. And DDI is HSW only, so
none of the changes apply there.
v2: Use hdmi_reg color format to detect 12bpc HDMI case
v3: Set adjusted_mode.clock for LVDS too
v4: Rename ironlake_crtc_clock_get to ironlake_pch_clock_get,
eliminate the useless link_freq variable.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add the 120MHz refernce clock case for PCH DPLLs.
Also determine the reference clock frequency more accurately by
checking for the PLLB_REF_INPUT_SPREADSPECTRUMIN refclk input
mode. The gen2 code already checked it, but it stil assumed a
fixed 66MHz refclk. Instead we need to consult the VBT for the
real value.
v2: Fix refclk for SSC panel case
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already extract the DPLL state to pipe_config, so let's make use of
it in i9xx_crtc_clock_get() and avoid the register reads.
This will also make the function closer to being useable with PCH DPLL
since the registers for those live in a different address.
Also kill the useless adjusted_mode.clock zeroing. It's already zero at
this point.
v2: Read out DPLL state in intel_crtc_mode_get()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Extract the code to calculate the dotclock from the link clock and M/N
values into a new function from ironlake_crtc_clock_get().
The new function can be used to calculate the dotclock for both FDI and
DP cases.
Also simplify the code a bit along the way.
v2: Don't forget about non-pch encoders in ironlake_crtc_clock_get()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In case of error, the function drm_prime_pages_to_sg() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Now that DRM_EXYNOS depends on OF, we do not need individual
drivers to depend on it.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Putting everything into VRAM seems to help.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
We were using the wrong set_properly callback so we always
ended up with Full scaling even if something else (Center or
Full aspect) was selected.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Calling force_performance_level() from set_power_state()
doesn't work on some asics because the current power
state pointer has not been properly updated at that point.
Move the calls to force_performance_level() out of the
asic specific set_power_state() functions and into
the main power state sequence.
Fixes dpm resume on SI.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
I keep making that one, so checked if I was the only one. Apparently
not.
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If the low and high sclks within a power state are the same,
there no need to enable sclk scaling. Enabling sclk scaling
can cause display stability issues on some boards.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
If the low and high sclks are the same, there is no need to
enable sclk scaling. This causes display stability issues on
certain boards.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=60857
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Christian König <christian.koenig@amd.com>
Since the clock scaling is based on fb divider adjustments,
make sure the other pll parameters are the same.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
This very much looks like copypasta from drm/i915's fault handler.
It was used there to duct-tape over issues around gpu reset handling.
Since that can't ever happen for udl and there's seemingly no other
reason for this just drop it.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Radeon drm fixes for 3.12. All over the place (display, dpm, uvd, etc.).
Also adds a couple more berlin pci ids.
* 'drm-fixes-3.12' of git://people.freedesktop.org/~agd5f/linux: (25 commits)
drm/radeon/dpm: add bapm callback for kb/kv
drm/radeon/dpm: add bapm callback for trinity
drm/radeon/dpm: add infrastructure to properly handle bapm
drm/radeon/dpm: handle bapm on kb/kv
drm/radeon/dpm: handle bapm on trinity
drm/radeon: expose DPM thermal thresholds through sysfs
drm/radeon: simplify driver data retrieval
drm/radeon/atom: workaround vbios bug in transmitter table on rs880 (v2)
drm/radeon/dpm: fix fallback for empty UVD clocks
drm/radeon: add command submission tracepoint
drm/radeon: remove stale radeon_fence_retire tracepoint
drm/radeon/r6xx: add a stubbed out set_uvd_clocks callback
drm/radeon: fix typo in PG flags
drm/radeon: add some additional berlin pci ids
drm/radeon/cik: update gpu_init for an additional berlin gpu
drm/radeon: add spinlocks for indirect register accesss
drm/radeon: protect concurrent smc register access with a spinlock
drm/radeon: dpm updates for KV
drm/radeon: signedness bug in kv_dpm.c
drm/radeon: clean up r600_free_extended_power_table()
...
We don't seem to be using the pointer after it's unmapped, so this
patch doesn't fix any bug I can reproduce.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The cursor is supposed to be disabled during crtc mode set (disabled by
ctrc disable). Assert this is the case.
v2: move cursor disabled assert next to plane asserts (Ville)
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The buf pointer used during l3_write is just char *, therefore it does
not require the silly any addition of offset.
v2: Also fix i915_l3_read with a suggested logic from Ville
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We always read a register for l3 parity reads, and we don't really want
to ever let userspace trick us into giving back less than the dword.
Writes are okay because we assume everything will be 0 filled, and as
such, if a user really wants to write less than a dword, let them.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Sadly, this isn't the first time we've done this:
http://lists.freedesktop.org/archives/intel-gfx/2013-June/029065.html
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to do fuzzy clock checks for other things besides
adjusted_mode.clock, so just pass two two clocks to compare
to intel_fuzzy_clock_check().
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add functions to read out the CPU and PCH transcoder M/N values,
and use them to fill out the pipe config dp_m_n information. And
while at it populate has_dp_encoder too.
Also refactor ironlake_get_fdi_m_n_config() to simply call the new
intel_cpu_transcoder_get_m_n() function.
v2: Remember the DDI
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On CTG+ read out the pipe bpp setting from hardware and fill it into
pipe config. Also check it appropriately.
v2: Don't do the pipe_bpp extraction inside the PCH only code block on
ILK+.
Avoid the PIPECONF read as we already have read it for the
PIPECONF_EANBLE check.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It would be easier if adjusted_mode.clock would be the pipe pixel clock,
and it actually is, except for the cases where pixel_multiplier > 1.
So let's change intel_sdvo to use port_clock as the multiplied clock,
and then we can leave adjusted_mode.clock as pipe pixel clock.
v2: Improve port_clock documentation
Rebased on top of SDVO pixel_multiplier fixes
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We feed the non-multiplied clock to intel_link_compute_m_n(), so the
opposite operation should use the same order of operations. So we just
multiply by pixel_multiplier in the end now.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because this PCI config register doesn't exist on Gen5+.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Both callers had code to sanitize the uncore and restore the GTT
mappings just before calling __i915_drm_thaw, so Chris suggested I
should unify the code.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull vfs pile 4 from Al Viro:
"list_lru pile, mostly"
This came out of Andrew's pile, Al ended up doing the merge work so that
Andrew didn't have to.
Additionally, a few fixes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (42 commits)
super: fix for destroy lrus
list_lru: dynamically adjust node arrays
shrinker: Kill old ->shrink API.
shrinker: convert remaining shrinkers to count/scan API
staging/lustre/libcfs: cleanup linux-mem.h
staging/lustre/ptlrpc: convert to new shrinker API
staging/lustre/obdclass: convert lu_object shrinker to count/scan API
staging/lustre/ldlm: convert to shrinkers to count/scan API
hugepage: convert huge zero page shrinker to new shrinker API
i915: bail out earlier when shrinker cannot acquire mutex
drivers: convert shrinkers to new count/scan API
fs: convert fs shrinkers to new scan/count API
xfs: fix dquot isolation hang
xfs-convert-dquot-cache-lru-to-list_lru-fix
xfs: convert dquot cache lru to list_lru
xfs: rework buffer dispose list tracking
xfs-convert-buftarg-lru-to-generic-code-fix
xfs: convert buftarg LRU to generic code
fs: convert inode and dentry shrinking to be node aware
vmscan: per-node deferred work
...
This is just a remnant from the old days when our reset handling was
horribly racy, suffered from terribly locking issues and often happily
live-locked. Those days are now gone so we can drop the hacks and just
rip the reschedule-point out.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When reserving objects during execbuf, it is possible to come across an
object which will not fit given the current fragmentation of the address
space. We do not have any defragment in drm_mm, so the strategy is to
instead evict everything, and reallocate objects.
With the upcoming addition of multiple VMs, there is no point to evict
everything since doing so is overkill for the specific case mentioned
above.
Recommended-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: One additional s/evict_everything/evict_vm/ to update a
comment in the code.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As we'll see in the next patch, being able to evict for just 1 VM is
handy.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
lifted from Daniel:
pread/pwrite isn't about the object's domain at all, but purely about
synchronizing for outstanding rendering. Replacing the call to
set_to_gtt_domain with a wait_rendering would imo improve code
readability. Furthermore we could pimp pread to only block for
outstanding writes and not for reads.
Since you're not the first one to trip over this: Can I volunteer you
for a follow-up patch to fix this?
v2: Switch the pwrite patch to use \!read_only. This was a typo in the
original code. (Chris, Daniel)
Recommended-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Fix up the logic fumble - wait_rendering has a bool readonly
paramater, set_to_gtt_domain otoh has bool write. Breakage reported by
Jani Nikula, I've double-checked that igt/gem_concurrent_blt/prw-*
would have caught this.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When porting from UMS I mistyped this from the wrong place, AST noticed
and pointed it out, so we should fix it to be like the X.org driver.
Reported-by: Y.C. Chen <yc_chen@aspeedtech.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Yet another regression due to
commit 135c81b8c3
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Jul 21 21:37:09 2013 +0200
drm/i915: clean up crtc timings computation
I'm starting to wonder whether this was worth it ...
v2: Actually make it compile.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We've failed to properly clear out the flags when converting a dtd to
a drm mode. For more paranoia just memset the entire structure (and
drop the now redundant clears).
Also since
commit 135c81b8c3
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Jul 21 21:37:09 2013 +0200
drm/i915: clean up crtc timings computation
we don't update the crtc timings any more properly, so do that again.
v2: Remove more redundant clearing, spotted by Ville.
v3: Actually make it compile. Oops.
v4: Use a temporary structure to fill in the mode and copy it over
with drm_mode_copy. This will ensure we don't clobber the mode list or
id. Suggested by Ville.
Cc: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Use the = {}; structure clearing instead of memset as
suggested by Ville.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Occasionally we seem to miss an IRQ from the ME (microengine). I'm not
entirely sure the root cause, but for now we can unwedge things by
retiring from the hangcheck timer.
Signed-off-by: Rob Clark <robdclark@gmail.com>
When we CPU_PREP a bo with NOSYNC flag (for example, to implement
PIPE_TRANSFER_DISCARD_WHOLE_RESOURCE), an -EBUSY return indicates to
userspace that the bo is still busy. Previously it was incorrectly
returning 0 in this case.
And while we're in there throw in an bit of extra sanity checking in
case userspace tries to wait for a bogus fence.
Signed-off-by: Rob Clark <robdclark@gmail.com>
In case of error, the function drm_prime_pages_to_sg() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
bapm is a pm feature for sharing the power budget between
the GPU and the CPU on APUs. It needs to be enabled or
disabled in certain circumstances. For now, disable it
when on battery and enable it when on AC power.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
bapm is a power management feature for handling the
power budget between the CPU and GPU on APUs. This
patch adds support for enabling or disabling it.
For now disable it by default. Enabling it properly
requires quite a bit more work and will be addressed
in a separate patch.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
bapm is a power management feature for handling the
power budget between the CPU and GPU on APUs. This
patch adds support for enabling or disabling it.
For now disable it by default. Enabling it properly
requires quite a bit more work and will be addressed
in a separate patch.
This patch fixes hangs on boot on certain trinity
laptops when the system is on battery power.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The hwmon sysfs interface allows exposing temperature limits. The "max"
and "min" thresholds will be exposed as a critical high limit and its
hysteresis value, respectively. This gives the user a better idea of how
well cooling is doing and whether it is sufficient.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
You can get the driver data from struct device directly, there's no
need to get the PCI device first.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The OUTPUT_ENABLE action jumps past the point in the coder where
the data_offset is set on certain rs780 cards. This worked
previously because the OUTPUT_ENABLE action is always called
immediately after the ENABLE action so the data_offset remained
set. In 6f8bbaf568
(drm/radeon/atom: initialize more atom interpretor elements to 0),
we explictly reset data_offset to 0 between atom calls which then
caused this to fail. The fix is to just skip calling the
OUTPUT_ENABLE action on the problematic chipsets. The ENABLE
action does the same thing and more. Ultimately, we could
probably drop the OUTPUT_ENABLE action all together on DCE3
asics.
fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=60791
v2: only rs880 seems to be affected
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Some older 6xx-7xx boards didn't always fill in the
UVD clocks properly in the UVD power states. This
leads to the driver trying to set a 0 clock which
results in slow or broken UVD playback.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=69120
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Neither complete nor perfect, but solves my problem at hand
and might be useful in the future.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Certain r6xx boards use the same power state for both UVD
and other things. Since we don't support UVD on r6xx boards
at the moment, there was no callback installed for setting
the UVD clocks, however, on systems that use the same power
state, this leads to a NULL pointer dereference. Fill
in a stubbed out implementation for now to avoid the crash.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=66963
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: "3.11" <stable@vger.kernel.org>
This adds spinlocks to protect access to other
indirect register apertures. These indirect spaces are
used pretty infrequently and we haven't had an reported
problems, but better safe than sorry.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
smc registers are access indirectly via the main mmio aperture, so
there may be problems with concurrent access. This adds a spinlock
to protect access to this register space.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This updates dpm support for KV asics. Notably there
are some changes in acp handling and forcing performance
levels.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The problem here is that "unsigned i" is always greater than or equal to
zero. These loops mostly have a second check for "(i == 0)" so only the
last two are actually buggy. The rest is just cleanup.
Bug 1: kv_force_dpm_highest() doesn't have an "(i == 0)" check so it's
a potential forever loop.
Bug 2: In kv_get_sleep_divider_id_from_clock() there is a typo and the
test is reversed "<=" vs ">" so we never enter the loop. That means
normally we return KV_MAX_DEEPSLEEP_DIVIDER_ID (5). The return value
from here is saved in ->DeepSleepDivId and I wasn't able to determine
how that is used. This is a static checker fix and I have not tested
it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
kfree() can accept NULL pointers so I have removed the checks. Also
I've used a pointer to shorten the lines.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This provides a connector property to enable/disable hdmi
audio on the fly. The default is disabled, but you can select
auto (let the driver detect an audio capable monitor and enable it)
or enabled (force audio enabled). This also enables audio by
default so you no longer need a module parameter to enable audio.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Make sure the audio pin is valid before accessing its members.
Noticed by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Allows you to limit the selected power levels via sysfs.
Force the feedback divider to select a power level.
v2: fix checking in rs780_force_fbdiv,
drop a duplicate divider structure in rs780_dpm_force_performance_level,
Force the voltage level too.
Signed-off-by: Anthoine Bourgeois <anthoine.bourgeois@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The internal cp interrupts need to be enabled and
disabled at specific times in order clockgating to
work properly. This patch changes the handling
of the CP_INT_CNTL register to respect the current
state of the internal CP interrupts when making
changes to the other interrupts in CP_INT_CNTL.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The internal cp interrupts need to be enabled and
disabled at specific times in order clockgating to
work properly. This patch changes the handling
of the CP_INT_CNTL register to respect the current
state of the internal CP interrupts when making
changes to the other interrupts in CP_INT_CNTL.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pull drm fixes from Dave Airlie:
"Daniel had some fixes queued up, that were delayed, the stolen memory
ones and vga arbiter ones are quite useful, along with his usual bunch
of stuff, nothing for HSW outputs yet.
The one nouveau fix is for a regression I caused with the poweroff stuff"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (30 commits)
drm/nouveau: fix oops on runtime suspend/resume
drm/i915: Delay disabling of VGA memory until vgacon->fbcon handoff is done
drm/i915: try not to lose backlight CBLV precision
drm/i915: Confine page flips to BCS on Valleyview
drm/i915: Skip stolen region initialisation if none is reserved
drm/i915: fix gpu hang vs. flip stall deadlocks
drm/i915: Hold an object reference whilst we shrink it
drm/i915: fix i9xx_crtc_clock_get for multiplied pixels
drm/i915: handle sdvo input pixel multiplier correctly again
drm/i915: fix hpd work vs. flush_work in the pageflip code deadlock
drm/i915: fix up the relocate_entry refactoring
drm/i915: Fix pipe config warnings when dealing with LVDS fixed mode
drm/i915: Don't call sg_free_table() if sg_alloc_table() fails
i915: Update VGA arbiter support for newer devices
vgaarb: Fix VGA decodes changes
vgaarb: Don't disable resources that are not owned
drm/i915: Pin pages whilst mapping the dma-buf
drm/i915: enable trickle feed on Haswell
x86: add early quirk for reserving Intel graphics stolen memory v5
drm/i915: split PCI IDs out into i915_drm.h v4
...
The main shrinker driver will keep trying for a while to free objects if
the returned value from the shrink scan procedure is 0. That means "no
objects now", but a retry could very well succeed.
But what we should say here is a different thing: that it is impossible to
shrink, and we would better bail out soon. We find this behavior more
appropriate for the case where the lock cannot be taken. Specially given
the hammer behavior of the i915: if another thread is already shrinking,
we are likely not to be able to shrink anything anyway when we finally
acquire the mutex.
Signed-off-by: Glauber Costa <glommer@openvz.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Chinner <dchinner@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: Arve Hjønnevåg <arve@android.com>
Cc: Carlos Maiolino <cmaiolino@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Chuck Lever <chuck.lever@oracle.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Rientjes <rientjes@google.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: J. Bruce Fields <bfields@redhat.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Convert the driver shrinkers to the new API. Most changes are compile
tested only because I either don't have the hardware or it's staging
stuff.
FWIW, the md and android code is pretty good, but the rest of it makes me
want to claw my eyes out. The amount of broken code I just encountered is
mind boggling. I've added comments explaining what is broken, but I fear
that some of the code would be best dealt with by being dragged behind the
bike shed, burying in mud up to it's neck and then run over repeatedly
with a blunt lawn mower.
Special mention goes to the zcache/zcache2 drivers. They can't co-exist
in the build at the same time, they are under different menu options in
menuconfig, they only show up when you've got the right set of mm
subsystem options configured and so even compile testing is an exercise in
pulling teeth. And that doesn't even take into account the horrible,
broken code...
[glommer@openvz.org: fixes for i915, android lowmem, zcache, bcache]
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Glauber Costa <glommer@openvz.org>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: Arve Hjønnevåg <arve@android.com>
Cc: Carlos Maiolino <cmaiolino@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Chuck Lever <chuck.lever@oracle.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Rientjes <rientjes@google.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: J. Bruce Fields <bfields@redhat.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Fixed with
commit 10603caacf
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Aug 26 19:51:06 2013 -0300
drm/i915: Apply the force-detect VGA w/a to Valleyview
Signed-off-by: Jesse Barnes <jbarnes@virtuosugeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Need to check size+offset against bo size (duh!).. now we have a test
case to make sure I've done it right:
https://github.com/freedreno/msmtest/blob/master/submittest.c
Also, use DRM_ERROR() for error case traces, which makes debugging
userspace easier when enabling debug traces is too much.
Signed-off-by: Rob Clark <robdclark@gmail.com>
If gpu locks up with the rptr shortly beyond the wrap-around point in
the ringbuffer, because the rptr was not reset (but wptr is, by virtue
of resetting rb->cur), we could end up in a scenario where we think
there is not enough space in the ringbuffer for the next cmds. And
since the CP won't reset rptr until after processing an IB, this leaves
things in a sort of deadlock.
So reset rptr too. And a bit more spiffing up of hangcheck to make
things easier to debug.
Signed-off-by: Rob Clark <robdclark@gmail.com>
The userspace API already had everything needed to handle read vs write
synchronization. This patch actually bothers to hook it up properly, so
that we don't need to (for example) stall on userspace read access to a
buffer that gpu is also still reading.
Signed-off-by: Rob Clark <robdclark@gmail.com>
intel_ddi_enable_transcoder_func() picked the sync flags from crtc->mode
instead of the pipe config adjusted_mode. Fix the problem and hopefully
rid my HSW machine of the remaining pipe config warnings.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The purpose of the function is to find out whether the object is still
bound in any address space. This can be easily checked by looking at the
vma currently associated with the object, rather than asking if any of
the global address spaces have an active vma on the object.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ignoring the legacy DRI1 code, and a couple of special cases (to be
discussed later), all access to the ring is mediated through requests.
The first write to a ring will grab a seqno and mark the ring as having
an outstanding_lazy_request. Either through explicitly adding a request
after an execbuffer or through an implicit wait (either by the CPU or by
a semaphore), that sequence of writes will be terminated with a request.
So we can ellide all the intervening writes to the tail register and
send the entire command stream to the GPU at once. This will reduce the
number of *serialising* writes to the tail register by a factor or 3-5
times (depending upon architecture and number of workarounds, context
switches, etc involved). This becomes even more noticeable when the
register write is overloaded with a number of debugging tools. The
astute reader will wonder if it is then possible to overflow the ring
with a single command. It is not. When we start a command sequence to
the ring, we check for available space and issue a wait in case we have
not. The ring wait will in this case be forced to flush the outstanding
register write and then poll the ACTHD for sufficient space to continue.
The exception to the rule where everything is inside a request are a few
initialisation cases where we may want to write GPU commands via the CS
before userspace wakes up and page flips.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of just a flag bit for each of the positive/negative sync
modes drm actually uses a separate flag for each ... This upsets the
modeset checker since the adjusted mode filled out at modeset time
doesn't match the one reconstructed at check time (since the
->get_config callback already gets this right).
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
Cc: Knut Petersen <Knut_Petersen@t-online.de>
References: http://www.gossamer-threads.com/lists/linux/kernel/1778688?do=post_view_threaded
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull the expected max WM level determinations out to a separate
function. Will have another user soon.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Unify the code a bit to use ilk_compute_wm_level for all watermark
levels.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
hsw_pipe_wm_parameters and hsw_wm_maximums typically are read only. Make
them const.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make the call to intel_update_watermarks() just once or twice during
modeset. Ideally it should happen independently when each plane gets
enabled/disabled, but for now it seems better to keep it in central
place. We can improve things when we get all the planes sorted out
in a better way.
When enabling set up the watermarks just before the pipe is enabled.
And when disabling we need to wait until we've marked the crtc as
inactive, as otherwise intel_crtc_active() would still think the pipe
is enabled and the computed watermarks would reflect that.
v2: Pimp up the commit message a bit
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Passing the appropriate crtc to intel_update_watermarks() should help
in avoiding needless work in the future.
v2: Avoid clash with internal 'crtc' variable in some wm functions
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Replace "%8x" with "%08x".
The hex number should be shown with zero stuffed instead of spaces.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
if we have no crtcs we need to not call the display resume code.
Reported-by: Tobias Klausmann <tobias.johannes.klausmann@mni.thm.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Early stolen mem reservation from Jesse in x86 boot code. Acked by Ingo
and hpa. This was ready much earlier but somehow I've thought it'd go
in through x86 trees, hence why this is late. Avoids the pci resource
code to plant mmiobars in the middle of stolen mem and other ugliness.
- vgaarb improvements from Alex Williamson plus the fix from Ville for the
vgacon->fbcon smooth transition "feature".
- Render pageflips on ivb/hsw to avoid stalls due to the ring switching
when only flipping on the blitter (Chris).
- Deadlock fixes around our flush_workqueue which crept back in - lockdep
isn't clever enough :(
- Shrinker recursion fix from Chris - this is the thing that blew the vma
patches from Ben I've taken out of 3.12.
- Fixup for the relocation refactoring. Also an igt testcase to make sure
we don't break this again.
- Pile of smaller fixups all over, shortlog has full details.
* tag 'drm-intel-fixes-2013-09-06' of git://people.freedesktop.org/~danvet/drm-intel: (29 commits)
drm/i915: Delay disabling of VGA memory until vgacon->fbcon handoff is done
drm/i915: try not to lose backlight CBLV precision
drm/i915: Confine page flips to BCS on Valleyview
drm/i915: Skip stolen region initialisation if none is reserved
drm/i915: fix gpu hang vs. flip stall deadlocks
drm/i915: Hold an object reference whilst we shrink it
drm/i915: fix i9xx_crtc_clock_get for multiplied pixels
drm/i915: handle sdvo input pixel multiplier correctly again
drm/i915: fix hpd work vs. flush_work in the pageflip code deadlock
drm/i915: fix up the relocate_entry refactoring
drm/i915: Fix pipe config warnings when dealing with LVDS fixed mode
drm/i915: Don't call sg_free_table() if sg_alloc_table() fails
i915: Update VGA arbiter support for newer devices
vgaarb: Fix VGA decodes changes
vgaarb: Don't disable resources that are not owned
drm/i915: Pin pages whilst mapping the dma-buf
drm/i915: enable trickle feed on Haswell
x86: add early quirk for reserving Intel graphics stolen memory v5
drm/i915: split PCI IDs out into i915_drm.h v4
i915_gem: Convert kmem_cache_alloc(...GFP_ZERO) to kmem_cache_zalloc
...
My g33 here seems to be shockingly good at hitting them all. This time
around kms_flip/flip-vs-panning-vs-hang blows up:
intel_crtc_wait_for_pending_flips correctly checks for gpu hangs and
if a gpu hang is pending aborts the wait for outstanding flips so that
the setcrtc call will succeed and release the crtc mutex. And the gpu
hang handler needs that lock in intel_display_handle_reset to be able
to complete outstanding flips.
The problem is that we can race in two ways:
- Waiters on the dev_priv->pending_flip_queue aren't woken up after
we've the reset as pending, but before we actually start the reset
work. This means that the waiter doesn't notice the pending reset
and hence will keep on hogging the locks.
Like with dev->struct_mutex and the ring->irq_queue wait queues we
there need to wake up everyone that potentially holds a lock which
the reset handler needs.
- intel_display_handle_reset was called _after_ we've already
signalled the completion of the reset work. Which means a waiter
could sneak in, grab the lock and never release it (since the
pageflips won't ever get released).
Similar to resetting the gem state all the reset work must complete
before we update the reset counter. Contrary to the gem reset we
don't need to have a second explicit wake up call since that will
have happened already when completing the pageflips. We also don't
have any issues that the completion happens while the reset state is
still pending - wait_for_pending_flips is only there to ensure we
display the right frame. After a gpu hang&reset events such
guarantees are out the window anyway. This is in contrast to the gem
code where too-early wake-up would result in unnecessary restarting
of ioctls.
Also, since we've gotten these various deadlocks and ordering
constraints wrong so often throw copious amounts of comments at the
code.
This deadlock regression has been introduced in the commit which added
the pageflip reset logic to the gpu hang work:
commit 96a02917a0
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Feb 18 19:08:49 2013 +0200
drm/i915: Finish page flips and update primary planes after a GPU reset
v2:
- Add comments to explain how the wake_up serves as memory barriers
for the atomic_t reset counter.
- Improve the comments a bit as suggested by Chris Wilson.
- Extract the wake_up calls before/after the reset into a little
i915_error_wake_up and unconditionally wake up the
pending_flip_queue waiters, again as suggested by Chris Wilson.
v3: Throw copious amounts of comments at i915_error_wake_up as
suggested by Chris Wilson.
Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Detangle the additional state of whether or not the hw has the pfit
enabled from whether it has zero size. This allows us to cleanly
distinguish in the code when we expect the pfit to be enabled (for
Haswell pc8), and when the BIOS is confused and needs sanitizing.
Reported-by: shui yanwei <yangweix.shui@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=68251
Tested-by: shui yanwei <yangweix.shui@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When transitioning away from vgacon the system tries to save the
current contents of the VGA memory, so that it can be cleanly handed
off to fbcon (or whatever comes afterwards).
The recent change
commit 81b5c7bc8d
Author: Alex Williamson <alex.williamson@redhat.com>
Date: Wed Aug 28 09:39:08 2013 -0600
i915: Update VGA arbiter support for newer devices
caused i915 to disable VGA memory decode for the IGD when i915 is
initializing. Unfortunately that happens before the vgacon->fbcon
handoff so vgacon_save_screen() will read out all ones from the
VGA memory.
After the handoff fbcon will inherit the bogus state from vgacon,
and pre-fills the fb with matching contents. The end result is
a white rectangle in the top left corner of the screen, the size
of which matches the now inactive VGA console.
To remedy the situation delay the disabling of VGA memory until
the vgacon->fbcon handoff has happened.
Also rename i915_enable_vga to i915_enable_vga_mem to make
the relationship between these functions clearer.
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull trivial tree from Jiri Kosina:
"The usual trivial updates all over the tree -- mostly typo fixes and
documentation updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (52 commits)
doc: Documentation/cputopology.txt fix typo
treewide: Convert retrun typos to return
Fix comment typo for init_cma_reserved_pageblock
Documentation/trace: Correcting and extending tracepoint documentation
mm/hotplug: fix a typo in Documentation/memory-hotplug.txt
power: Documentation: Update s2ram link
doc: fix a typo in Documentation/00-INDEX
Documentation/printk-formats.txt: No casts needed for u64/s64
doc: Fix typo "is is" in Documentations
treewide: Fix printks with 0x%#
zram: doc fixes
Documentation/kmemcheck: update kmemcheck documentation
doc: documentation/hwspinlock.txt fix typo
PM / Hibernate: add section for resume options
doc: filesystems : Fix typo in Documentations/filesystems
scsi/megaraid fixed several typos in comments
ppc: init_32: Fix error typo "CONFIG_START_KERNEL"
treewide: Add __GFP_NOWARN to k.alloc calls with v.alloc fallbacks
page_isolation: Fix a comment typo in test_pages_isolated()
doc: fix a typo about irq affinity
...
Score and action reveals what all the rings were doing
and why hang was declared. Add idle state so that
we can distinguish between waiting and idle ring.
v2: - add idle as a hangcheck action
- consensed hangcheck status to single line (Chris)
- mark active explicitly when we are making progress (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now when we have mechanism in place to track which context
was guilty of hanging the gpu, it is possible to punish
for bad behaviour.
If context has recently submitted a faulty batchbuffers guilty of
gpu hang and submits another batch which hangs gpu in quick
succession, ban it permanently. If ctx is banned, no more
batchbuffers will be queued for execution.
There is no need for global wedge machinery anymore and
it would be unwise to wedge the whole gpu if we have multiple
hanging batches queued for execution. Instead just ban
the guilty ones and carry on.
v2: Store guilty ban status bool in gpu_error instead of pointers
that might become danling before hang is declared.
v3: Use return value for banned status instead of stashing state
into gpu_error (Chris Wilson)
v4: - rebase on top of fixed hang stats api
- add define for ban period
- rename commit and improve commit msg
v5: - rely context banning instead of wedging the gpu
- beautification and fix for ban calculation (Chris)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV has per-pipe PP registers. Set up power sequencing on mode set. The
connector init time setup is problematic, since we don't have a pipe at
that time. Cook up something.
v2:
- use vlv_power_sequencer_pipe() also in _pp_{ctrl,stat}_reg()
- use PANEL_PORT_SELECT_DPC_VLV (Ville)
v3: make checkpatch happier
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Make checkpatch a bit more happier still ...]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove duplicates, add VLV specific macros for port B and C.
v2: also add PANEL_PORT_SELECT_DPC_VLV for clarity (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Follow-up to
commit 5004945f1d
Author: Jani Nikula <jani.nikula@intel.com>
Date: Tue Jul 30 12:20:32 2013 +0300
drm/i915: move encoder->enable callback later in VLV crtc enable
v2: Rebase on the renamed enable hooks, adding clarity (Ville)
Reference: http://mid.gmane.org/CAKMK7uFs9EMvMW8BnS24e5UNm1D7JrfVg3SD5SDFtVEamGfOOg@mail.gmail.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In line with the rest of the code base. No functional changes.
v2: also s/intel_pre_enable_dp/g4x_pre_enable_dp/ for consistency (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ACPI has _BCM and _BQC methods to set and query the backlight
brightness, respectively. The ACPI opregion has variables BCLP and CBLV
to hold the requested and current backlight brightness, respectively.
The BCLP variable has range 0..255 while the others have range
0..100. This means the _BCM method has to scale the brightness for BCLP,
and the gfx driver has to scale the requested value back for CBLV. If
the _BQC method uses the CBLV variable (apparently some implementations
do, some don't) for current backlight level reporting, there's room for
rounding errors.
Use DIV_ROUND_UP for scaling back to CBLV to get back to the same values
that were passed to _BCM, presuming the _BCM simply uses bclp = (in *
255) / 100 for scaling to BCLP.
Reference: https://gist.github.com/aaronlu/6314920
Reported-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Once again we find that Valleyview is ever so subtlety different from
the rest of its gen7 brethen. In this case, Valleyview has no support
for pageflipping from the RCS ring.
Fixes a regression from
commit ffe74d7550
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Aug 26 20:58:12 2013 +0100
drm/i915: Use RCS flips on Ivybridge+
Reported-by: "Lee, Chon Ming" <chon.ming.lee@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=68968
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's totally unused, so remove the last mode_fixup appearance in i915.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm tree changes from Dave Airlie:
"This is the main drm pull request, I have some overlap with sound and
arm-soc, the sound patch is acked and may conflict based on -next
reports but should be a trivial fixup, which I'll leave to you!
Highlights:
- new drivers:
MSM driver from Rob Clark
- non-drm:
switcheroo and hdmi audio driver support for secondary GPU
poweroff, so drivers can use runtime PM to poweroff the GPUs. This
can save 5 or 6W on some optimus laptops.
- drm core:
combined GEM and TTM VMA manager
per-filp mmap permission tracking
initial rendernode support (via a runtime enable for now, until we get api stable),
remove old proc support,
lots of cleanups of legacy code
hdmi vendor infoframes and 4k modes
lots of gem/prime locking and races fixes
async pageflip scaffolding
drm bridge objects
- i915:
Haswell PC8+ support and eLLC support, HDMI 4K support, initial
per-process VMA pieces, watermark reworks, convert to generic hdmi
infoframes, encoder reworking, fastboot support,
- radeon:
CIK PM support, remove 3d blit code in favour of DMA engines,
Berlin GPU support, HDMI audio fixes
- nouveau:
secondary GPU power down support for optimus laptops, lots of
fixes, use MSI, VP3 engine support
- exynos:
runtime pm support for g2d, DT support, remove non-DT,
- tda998x i2c driver:
lots of fixes for sync issues
- gma500:
lots of cleanups
- rcar:
add LVDS support, fbdev emulation,
- tegra:
just minor fixes"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (684 commits)
drm/exynos: Fix build error with exynos_drm_connector.c
drm/exynos: Remove non-DT support in exynos_drm_fimd
drm/exynos: Remove non-DT support in exynos_hdmi
drm/exynos: Remove non-DT support in exynos_drm_g2d
drm/exynos: Remove non-DT support in exynos_hdmiphy
drm/exynos: Remove non-DT support in exynos_ddc
drm/exynos: Make Exynos DRM drivers depend on OF
drm/exynos: Consider fallback option to allocation fail
drm/exynos: fimd: move platform data parsing to separate function
drm/exynos: fimd: get signal polarities from device tree
drm/exynos: fimd: replace struct fb_videomode with videomode
drm/exynos: check a pixel format to a particular window layer
drm/exynos: fix fimd pixel format setting
drm/exynos: Add NULL pointer check
drm/exynos: Remove redundant error messages
drm/exynos: Add missing of.h header include
drm/exynos: Remove redundant NULL check in exynos_drm_buf
drm/exynos: add device tree support for rotator
drm/exynos: Add missing includes
drm/exynos: add runtime pm interfaces to g2d driver
...
* Change the OMAP board files to use the new OMAP display drivers
* Remove all the old drivers, and the related auxiliary code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Hj7U
-----END PGP SIGNATURE-----
Merge tag 'fbdev-3.12-omap-legacy-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull OMAP specific fbdev changes from Tomi Valkeinen:
"I've got this pull request separate from the main fbdev pull request,
as this contains a bunch of OMAP board file changes and thus could
possibly be rejected in case of bad conflicts.
The removal of the old display drivers depend on the board file
changes, so Tony Lindgren suggested taking them together via fbdev
tree. These are in linux-next, and also Tony didn't see any conflicts
with any of the branches he had, so they should go in clean.
- Change the OMAP board files to use the new OMAP display drivers
- Remove all the old drivers, and the related auxiliary code"
* tag 'fbdev-3.12-omap-legacy-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (35 commits)
OMAPDSS: rename omap_dss_device's 'device' field to 'dst'
OMAPDSS: rename omap_dss_device's 'output' to 'src'
OMAPDSS: DSS: remove legacy dss bus support
OMAPDSS: RFBI: remove code related to old panel model
OMAPDSS: VENC: remove code related to old panel model
OMAPDSS: SDI: remove code related to old panel model
OMAPDSS: DSI: remove code related to old panel model
OMAPDSS: HDMI: remove code related to old panel model
OMAPDSS: DPI: remove code related to old panel model
OMAPDSS: remove all old panel drivers
OMAPDSS: DPI: change regulator handling
OMAPDSS: SDI: change regulator handling
OMAPDSS: fix DPI and SDI device ids
OMAPDSS: remove omap_dss_device->channel field
OMAPDSS: RFBI: Mark RFBI as broken
ARM: OMAP2+: Remove old display drivers from omap2plus_defconfig
ARM: OMAP: AM3517EVM: use new display drivers
ARM: OMAP: Zoom: use new display drivers
ARM: OMAP: Pandora: use new display drivers
ARM: OMAP: OMAP3EVM: use new display drivers
...
Pull i2c updates from Wolfram Sang:
"Highlights:
- OF and ACPI helpers are now included in the core, and not in
external files anymore. This removes dependency problems for
modules and is cleaner, in general.
- mv64xxx-driver gains fifo usage to support mv78230
- imx-driver overhaul to support VF610
- various cleanups, most notably related to devm_* and CONFIG_PM
usage
- driver bugfixes and smaller feature additions"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (51 commits)
i2c: rcar: add rcar-H2 support
i2c: sirf: retry 3 times as sometimes we get random noack and timeout
i2c: sirf: support reverse direction of address
i2c: sirf: fix the typo for setting bitrate to less than 100k
i2c: sirf: we need to wait I2C_RESET status in resume
i2c: sirf: reset i2c controller early after we get a noack
i2c: designware: get SDA hold time, HCNT and LCNT configuration from ACPI
i2c: designware: make HCNT/LCNT values configurable
i2c: mpc: cleanup clock API use
i2c: pnx: fix error return code in i2c_pnx_probe()
i2c: ismt: add error return code in probe()
i2c: mv64xxx: fix typo in binding documentation
i2c: imx: use exact SoC revision to document binding
i2c: move ACPI helpers into the core
i2c: move OF helpers into the core
i2c: mv64xxx: Fix timing issue on Armada XP (errata FE-8471889)
i2c: mv64xxx: Add I2C Transaction Generator support
i2c: powermac: fix return path on error
Documentation: i2c: Fix example in instantiating-devices
i2c: tiny-usb: do not use stack as URB transfer_buffer
...
The patch doesn't contain functional change, but is to prepare for
future platform which has different DPIO phy. The additional pipe
parameter will use to select which phy to target for.
v2: Update the commit message and add static for the new function.
(Jani/Ville)
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo reported that if he set the amount of reserved memory to 0, then
we emitted a warning about a conflict before disabling our use of stolen
memory. This was introduced with
commit eaba1b8f33
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Thu Jul 4 12:28:35 2013 +0100
drm/i915: Verify that our stolen memory doesn't conflict
and is simply fixed by checking for a no reservation first.
Reported-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since we've started to clean up pending flips when the gpu hangs in
commit 96a02917a0
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Feb 18 19:08:49 2013 +0200
drm/i915: Finish page flips and update primary planes after a GPU reset
the gpu reset work now also grabs modeset locks. But since work items
on our private work queue are not allowed to do that due to the
flush_workqueue from the pageflip code this results in a neat
deadlock:
INFO: task kms_flip:14676 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
kms_flip D ffff88019283a5c0 0 14676 13344 0x00000004
ffff88018e62dbf8 0000000000000046 ffff88013bdb12e0 ffff88018e62dfd8
ffff88018e62dfd8 00000000001d3b00 ffff88019283a5c0 ffff88018ec21000
ffff88018f693f00 ffff88018eece000 ffff88018e62dd60 ffff88018eece898
Call Trace:
[<ffffffff8138ee7b>] schedule+0x60/0x62
[<ffffffffa046c0dd>] intel_crtc_wait_for_pending_flips+0xb2/0x114 [i915]
[<ffffffff81050ff4>] ? finish_wait+0x60/0x60
[<ffffffffa0478041>] intel_crtc_set_config+0x7f3/0x81e [i915]
[<ffffffffa031780a>] drm_mode_set_config_internal+0x4f/0xc6 [drm]
[<ffffffffa0319cf3>] drm_mode_setcrtc+0x44d/0x4f9 [drm]
[<ffffffff810e44da>] ? might_fault+0x38/0x86
[<ffffffffa030d51f>] drm_ioctl+0x2f9/0x447 [drm]
[<ffffffff8107a722>] ? trace_hardirqs_off+0xd/0xf
[<ffffffffa03198a6>] ? drm_mode_setplane+0x343/0x343 [drm]
[<ffffffff8112222f>] ? mntput_no_expire+0x3e/0x13d
[<ffffffff81117f33>] vfs_ioctl+0x18/0x34
[<ffffffff81118776>] do_vfs_ioctl+0x396/0x454
[<ffffffff81396b37>] ? sysret_check+0x1b/0x56
[<ffffffff81118886>] SyS_ioctl+0x52/0x7d
[<ffffffff81396b12>] system_call_fastpath+0x16/0x1b
2 locks held by kms_flip/14676:
#0: (&dev->mode_config.mutex){+.+.+.}, at: [<ffffffffa0316545>] drm_modeset_lock_all+0x22/0x59 [drm]
#1: (&crtc->mutex){+.+.+.}, at: [<ffffffffa031656b>] drm_modeset_lock_all+0x48/0x59 [drm]
INFO: task kworker/u8:4:175 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
kworker/u8:4 D ffff88018de9a5c0 0 175 2 0x00000000
Workqueue: i915 i915_error_work_func [i915]
ffff88018e37dc30 0000000000000046 ffff8801938ab8a0 ffff88018e37dfd8
ffff88018e37dfd8 00000000001d3b00 ffff88018de9a5c0 ffff88018ec21018
0000000000000246 ffff88018e37dca0 000000005a865a86 ffff88018de9a5c0
Call Trace:
[<ffffffff8138ee7b>] schedule+0x60/0x62
[<ffffffff8138f23d>] schedule_preempt_disabled+0x9/0xb
[<ffffffff8138d0cd>] mutex_lock_nested+0x205/0x3b1
[<ffffffffa0477094>] ? intel_display_handle_reset+0x7e/0xbd [i915]
[<ffffffffa0477094>] ? intel_display_handle_reset+0x7e/0xbd [i915]
[<ffffffffa0477094>] intel_display_handle_reset+0x7e/0xbd [i915]
[<ffffffffa044e0a2>] i915_error_work_func+0x128/0x147 [i915]
[<ffffffff8104a89a>] process_one_work+0x1d4/0x35a
[<ffffffff8104a821>] ? process_one_work+0x15b/0x35a
[<ffffffff8104b4a5>] worker_thread+0x144/0x1f0
[<ffffffff8104b361>] ? rescuer_thread+0x275/0x275
[<ffffffff8105076d>] kthread+0xac/0xb4
[<ffffffff81059d30>] ? finish_task_switch+0x3b/0xc0
[<ffffffff810506c1>] ? __kthread_parkme+0x60/0x60
[<ffffffff81396a6c>] ret_from_fork+0x7c/0xb0
[<ffffffff810506c1>] ? __kthread_parkme+0x60/0x60
3 locks held by kworker/u8:4/175:
#0: (i915){.+.+.+}, at: [<ffffffff8104a821>] process_one_work+0x15b/0x35a
#1: ((&dev_priv->gpu_error.work)){+.+.+.}, at: [<ffffffff8104a821>] process_one_work+0x15b/0x35a
#2: (&crtc->mutex){+.+.+.}, at: [<ffffffffa0477094>] intel_display_handle_reset+0x7e/0xbd [i915]
This blew up while running kms_flip/flip-vs-panning-vs-hang-interruptible
on one of my older machines.
Unfortunately (despite the proper lockdep annotations for
flush_workqueue) lockdep still doesn't detect this correctly, so we
need to rely on chance to discover these bugs.
Apply the usual bugfix and schedule the reset work on the system
workqueue to keep our own driver workqueue free of any modeset lock
grabbing.
Note that this is not a terribly serious regression since before the
offending commit we'd simply have stalled userspace forever due to
failing to abort all outstanding pageflips.
v2: Add a comment as requested by Chris.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Whilst running the shrinker, we need to hold a reference as we unbind
the objects, or else we may end up waiting for and retiring requests,
which in turn may result in this object being freed.
This is very similar to the eviction code which also has to be very
careful to keep a reference to its objects as it retires and unbinds
them.
Another similarity, that Ben pointed out, is that as we may call
retire-requests, the unbound_list is outside of our control. We must
only process a single element of that list at a time, that is we can not
rely on the "safe" next pointer being valid after a call to
i915_vma_unbind().
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
IP: [<ffffffffa0082892>] i915_gem_gtt_finish_object+0x68/0xbd [i915]
PGD 758d3067 PUD ac0d6067 PMD 0
Oops: 0000 [#1] SMP
Modules linked in: dm_mod snd_hda_codec_realtek iTCO_wdt iTCO_vendor_support pcspkr snd_hda_intel i2c_i801 snd_hda_codec snd_hwdep snd_pcm snd_page_alloc snd_timer snd lpc_ich mfd_core soundcore battery ac option usb_wwan usbserial uvcvideo videobuf2_vmalloc videobuf2_memops videobuf2_core videodev i915 video button drm_kms_helper drm acpi_cpufreq mperf freq_table
CPU: 1 PID: 16835 Comm: fbo-maxsize Not tainted 3.11.0-rc7_nightlytop_8fdad4_20130902_+ #7977
task: ffff8800712106d0 ti: ffff880028e4a000 task.ti: ffff880028e4a000
RIP: 0010:[<ffffffffa0082892>] [<ffffffffa0082892>] i915_gem_gtt_finish_object+0x68/0xbd [i915]
RSP: 0018:ffff880028e4b9e8 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff880145734000 RCX: ffff880145735328
RDX: ffff8801457353fc RSI: 0000000000000000 RDI: ffff88007597cc00
RBP: ffff88007597cc00 R08: 0000000000000001 R09: ffff88014f257f00
R10: ffffea0001d65f00 R11: 0000000000bba60b R12: ffff880149e5b000
R13: ffff880145734001 R14: ffff88007597ccc8 R15: ffff88007597cc00
FS: 00007ff5bc919740(0000) GS:ffff88014f240000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000008 CR3: 0000000028f4c000 CR4: 00000000001407e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Stack:
0000000000000000 ffff88007597cc00 ffff8801440d6840 0000000000000000
ffff880145734000 ffffffffa007c854 0000000000000010 ffff88007597c900
0000000000018000 00000000004a1201 ffff88007597cc60 ffffffffa007d183
Call Trace:
[<ffffffffa007c854>] ? i915_vma_unbind+0xe2/0x1d1 [i915]
[<ffffffffa007d183>] ? __i915_gem_shrink+0xf1/0x162 [i915]
[<ffffffffa007d2ee>] ? i915_gem_object_get_pages_gtt+0xfa/0x303 [i915]
[<ffffffffa00795f4>] ? i915_gem_object_get_pages+0x54/0x89 [i915]
[<ffffffffa007cbda>] ? i915_gem_object_pin+0x238/0x5ce [i915]
[<ffffffff812cba5f>] ? __sg_page_iter_next+0x2b/0x58
[<ffffffffa0082056>] ? gen6_ppgtt_insert_entries+0xf2/0x114 [i915]
[<ffffffffa007fe4b>] ? i915_gem_execbuffer_reserve_vma.isra.13+0x79/0x18d [i915]
[<ffffffffa008017c>] ? i915_gem_execbuffer_reserve+0x21d/0x347 [i915]
[<ffffffffa0080bfb>] ? i915_gem_do_execbuffer.isra.17+0x4f3/0xe61 [i915]
[<ffffffffa00795f4>] ? i915_gem_object_get_pages+0x54/0x89 [i915]
[<ffffffffa007e405>] ? i915_gem_pwrite_ioctl+0x743/0x7a5 [i915]
[<ffffffffa0081a46>] ? i915_gem_execbuffer2+0x15e/0x1e4 [i915]
[<ffffffffa000e20d>] ? drm_ioctl+0x2a5/0x3c4 [drm]
[<ffffffffa00818e8>] ? i915_gem_execbuffer+0x37f/0x37f [i915]
[<ffffffff816f64c0>] ? __do_page_fault+0x3ab/0x449
[<ffffffff810be3da>] ? do_mmap_pgoff+0x2b2/0x341
[<ffffffff810e49be>] ? vfs_ioctl+0x1e/0x31
[<ffffffff810e5194>] ? do_vfs_ioctl+0x3ad/0x3ef
[<ffffffff810e5224>] ? SyS_ioctl+0x4e/0x7e
[<ffffffff816f88d2>] ? system_call_fastpath+0x16/0x1b
Code: 52 0c a0 48 c7 c6 22 30 0d a0 31 c0 e8 ef 00 f9 ff bf c6 a7 00 00 e8 90 5d 24 e1 f6 85 13 01 00 00 10 75 44 48 8b 85 18 01 00 00 <8b> 50 08 48 8b 30 49 8b 84 24 88 02 00 00 48 89 c7 48 81 c7 98
RIP [<ffffffffa0082892>] i915_gem_gtt_finish_object+0x68/0xbd [i915]
RSP <ffff880028e4b9e8>
CR2: 0000000000000008
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=68171
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
[danvet: Bikeshed the comments a bit as discussed with Chris.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is possible for us to be forced to perform an allocation for the lazy
request whilst running the shrinker. This allocation may fail, leaving
us unable to reclaim any memory leading to premature OOM. A neat
solution to the problem is to preallocate the request at the same time
as acquiring the seqno for the ring transaction. This means that we can
report ENOMEM prior to touching the rings.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Prior to preallocating an request for lazy emission, rename the existing
field to make way (and differentiate the seqno from the request struct).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
exynos_drm_connector.c now uses videomode helper API. Hence select
VIDEOMODE_HELPERS at DRM_EXYNOS level itself instead of at
DRM_EXYNOS_FIMD to avoid the following compilation error when FIMD
is not selected (introduced by commit cf796235a6 "drm/exynos: fimd:
replace struct fb_videomode with videomode"):
drivers/built-in.o: In function `exynos_drm_connector_get_modes':
drivers/gpu/drm/exynos/exynos_drm_connector.c:86:
undefined reference to `drm_display_mode_from_videomode'
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Since commit 383ffda2fa ("ARM: EXYNOS: no more support non-DT
for EXYNOS SoCs"), Exynos platform is DT only. Hence remove
all the conditional macros and make the driver DT only.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Since commit 383ffda2fa ("ARM: EXYNOS: no more support non-DT
for EXYNOS SoCs"), Exynos platform is DT only. Hence remove
all the conditional macros and make the driver DT only.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Since commit 383ffda2fa ("ARM: EXYNOS: no more support non-DT
for EXYNOS SoCs"), Exynos platform is DT only. Hence remove
all the conditional macros and make the driver DT only.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Since commit 383ffda2fa ("ARM: EXYNOS: no more support non-DT
for EXYNOS SoCs"), Exynos platform is DT only. Hence remove
all the conditional macros and make the driver DT only.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Since commit 383ffda2fa ("ARM: EXYNOS: no more support non-DT
for EXYNOS SoCs"), Exynos platform is DT only. Hence remove
all the conditional macros and make the driver DT only.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Exynos is a DT-only platform. Add this info to Kconfig.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
To address the case where physically contiguous memory
MAY NOT be a mandatory requirement for framebuffer for
the application calling exynos_drm_gem_dumb_create,
the patch adds a feature to get non physically contiguous
memory for framebuffer, if physically contiguous memory
allocation fails and if IOMMU is supported.
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Arun Kumar <arun.kk@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The patch moves platfrom_data and device tree parsing
to separate function.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The patch adds code to get signal polarization setting
from device tree display-timings node.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The patch replaces all occurrences of struct fb_videomode by
more accurate struct videomode. The change allows to remove
mode conversion function and simplifies clock divider calculation.
Clock configuration is moved to separate function.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch checks if a requested window supports alpha channel or not.
In case of s3c64xx, window 0 doesn't support alpha channel so if
the request pixel format is ARGB8888 then change it to XRGB8888.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This patch fixes wrong pixel format setting.
A pixel format is decided according to bpp and depth, or user-requested
format but fimd driver considered only bpp value to decide a proper pixel
format. So this patch makes a proper pixel format to be set according
to drm_framebuffer's pixel_format which is set by addfb with bpp and
depth, or addfb2 with user-requested format.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The exynos4 platform is only dt-based since 3.10, we should convert driver data
and ids to dt-based parsing methods. The rotator driver has a limit table to get
size limit of input picture. Each SoCs has slightly different limit value
compared with any others.
For example, exynos4210's max_size of RGB888 is 16k x 16k. But, others have
8k x 8k. Another example the exynos5250 should have multiple of 2 pixel size
for its X/Y axis. Thus, we should keep different tables for each of them.
This patch also includes desciptions of each nodes for the rotator and specifies
a example how to bind it.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Ensure that all externally accessed functions are correctly prototyped
when defined in each file by making sure the headers with the protoypes
are included in the file with the definition.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch makes g2d power domain and clock to be controlled
through pm runtime interfaces instead of controlling them
respectively.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
While trying to get boot-logo up on exynos5420 SMDK which has eDP panel
connected with resolution 2560x1600, following error occured even with
IOMMU enabled:
[0.880000] [drm:lowlevel_buffer_allocate] *ERROR* failed to allocate buffer.
[0.890000] [drm] Initialized exynos 1.0.0 20110530 on minor 0
To address the cases where physically contiguous memory MAY NOT be a
mandatory requirement for fb, the patch adds a feature to get non physically
contiguous memory for fb if physically contiguous memory allocation fails
and if IOMMU is supported.
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Arun Kumar <arun.kk@samsung.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=LeaW
-----END PGP SIGNATURE-----
Merge tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull PTR_RET() removal patches from Rusty Russell:
"PTR_RET() is a weird name, and led to some confusing usage. We ended
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle"
[ There are still some PTR_RET users scattered about, with some of them
possibly being new, but most of them existing in Rusty's tree too. We
have that
#define PTR_RET(p) PTR_ERR_OR_ZERO(p)
thing in <linux/err.h>, so they continue to work for now - Linus ]
* tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
GFS2: Replace PTR_RET with PTR_ERR_OR_ZERO
Btrfs: volume: Replace PTR_RET with PTR_ERR_OR_ZERO
drm/cma: Replace PTR_RET with PTR_ERR_OR_ZERO
sh_veu: Replace PTR_RET with PTR_ERR_OR_ZERO
dma-buf: Replace PTR_RET with PTR_ERR_OR_ZERO
drivers/rtc: Replace PTR_RET with PTR_ERR_OR_ZERO
mm/oom_kill: remove weird use of ERR_PTR()/PTR_ERR().
staging/zcache: don't use PTR_RET().
remoteproc: don't use PTR_RET().
pinctrl: don't use PTR_RET().
acpi: Replace weird use of PTR_RET.
s390: Replace weird use of PTR_RET.
PTR_RET is now PTR_ERR_OR_ZERO(): Replace most.
PTR_RET is now PTR_ERR_OR_ZERO
Suppress warning of unused-variables by adding a BUG()+return for invalid
audio-formats.
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Alex Deucher <Alexander.Deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
ironlake_fdi_compute_config() already checks that we have enough
FDI bandwidth. And it doesn't just use a hardcoded value but takes
into account factors such as the actual FDI frequency, shared FDI
B/C lanes, etc.
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For DP pll settings, there is only two golden configs. Instead of
running through the algorithm to determine it, hardcode the value and get it
determine in intel_dp_set_clock.
v2: Rework on the intel_limit compiler warning. (Jani)
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
[danvet: Fix up checkpatch issues.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
eDP 1.4 supports 4-5 extra link rates in additional to current 2 link
rate. Create a structure to store the DPLL divisor data to improve
readability.
v2: Fix the gen4_dpll/pch_dpll initialization to C99
designated initializers, and use a single loop for all platforms. (Jani and Daniel)
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
[danvet: Fix up checkpatch warnings.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The spec says to notify prior to power down and after power up. It is
unclear whether it makes a difference.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Notifying the bios lets it enter power saving states.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The bios interface seems messy, and it's hard to tell what the bios
really wants. At first, only add support for DDI based machines (hsw+),
and see how it turns out.
The spec says to notify prior to power down and after power up. It is
unclear whether it makes a difference.
v2:
- squash notification function and callers patches together (Daniel)
- move callers to haswell_crtc_{enable,disable} (Daniel)
- rename notification function (Chris)
v3:
- separate notification function and callers again, as it's not clear
whether the display power state notification is the right thing to do
after all
v4: per Paulo's review:
- drop LVDS
- WARN on unsupported encoder types
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In preparation for followup work.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SWSCI is a driver to bios call interface.
This checks for SWSCI availability and bios requested callbacks, and
filters out any calls that shouldn't happen. This way the callers don't
need to do the checks all over the place.
v2: silence some checkpatch nagging
v3: set PCI_SWSCI bit 0 to trigger interrupt (Mengdong Lin)
v4: remove an extra #define (Jesse)
v5: spec says s/w is responsible for clearing PCI_SWSCI bit 0 too
v6: per Paulo's review and more:
- fix sub-function mask
- add exit parameter
- add define for set panel details call
- return more errors from swsci
- clean up the supported/requested callbacks bit masks mess
- use DSLP for timeout
- fix build for CONFIG_ACPI=n
v7: tiny adjustment of requested vs. supported SBCB callbacks handling (Paulo)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The comments were a little out-of-sequence with the code, forcing the
reader to jump around whilst reading. Whilst moving the comments around,
add one to explain the context reference.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We use the request to ensure we hold a reference to the context for the
duration that it remains in use by the ring. Each request only holds a
reference to the current context, hence we emit a request after
switching contexts with the final reference to the old context. However,
the extra interrupt caused by that request is not useful (no timing
critical function will wait for the context object), instead the overhead
of servicing the IRQ shows up in some (lightweight) benchmarks. In order
to keep the useful property of using the request to manage the context
lifetime, we want to add a dummy request that is associated with the
interrupt from the subsequent real request following the batch.
The extra interrupt was added as a side-effect of using
i915_add_request() in
commit 112522f678
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Thu May 2 16:48:07 2013 +0300
drm/i915: put context upon switching
v2: Daniel convinced me that the request here was solely for context
lifetime tracking and that we have the active ref to keep the object
alive whilst the MI_SET_CONTEXT. So the only concern then is which
context should get the blame for MI_SET_CONTEXT failing. The old scheme
added a request for the old context so that any hang upto and including
the switch away would mark the old context as guilty. Now any hang here
implicates the new context. However since we have already gone through a
complete flush with the last context in its last request, and all that
lies in no-man's-land is an invalidate flush and the MI_SET_CONTEXT, we
should be safe in not unduly placing blame on the new context.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The saga around the breadcrumb vmas used by execbuf continues ...
This time around we've managed to unconditionally move the object to
the unbound list on the last vma unbind even though it might never
have been on either the bound or unbound list. Hilarity ensued.
Chris Wilson tracked this one down but compared to his patches I've
simply opted to completely separate the unbound case for not-yet bound
vmas. Otherwise we imo end up with semantically hard to parse checks
around the list_move_tail(global_list, ...).
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <ben@bwidawsk.net>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=68462
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We still maintain code internally that cares about preliminary support.
Leaving the check here doesn't hurt anyone, and should keep things more
in line.
This time around, stick the info in the intel_info structure, and also
change the error from DRM_ERROR->DRM_INFO.
This is a partial revert of:
commit 590e4df8c8
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Wed May 8 10:45:15 2013 -0700
drm/i915: VLV support is no longer preliminary
Daniel, I'll provide the fix ups for internal too if/when you merge
this (if you want).
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Batchbuffers constructed by userspace can conditionalise their URB
allocations through the use of the MI_SET_PREDICATE command. This
command can read the MI_PREDICATE_RESULT_2 register to see how many
slices are enabled on GT3, and by virtue of the result, scale their
memory allocations to fit enabled memory.
Of course, this only works if the kernel sets the appropriate bit in the
register first.
v2: Better commit subject and message by Chris Wilson.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Credits-to: Yejun Guo <yejun.guo@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This fixes a printf warn from gcc:
drivers/gpu/drm/i915/intel_dsi_cmd.c: In function ‘dsi_vc_send_long’:
drivers/gpu/drm/i915/intel_dsi_cmd.c:181:2: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 7 has type ‘size_t’ [-Wformat=]
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Initial parsing of the VBT MIPI block. For now, just store the panel id
if found.
Note: Again there seems to be no documentation for this piece of lore.
The doc situation for byt+ is just a bad joke :(
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Note: No one seems to have docs for this, so this patch here is just
unreviewed black magic :(
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: ymohanma <yogesh.mohan.marimuthu@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Add note about the doc situation.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DPLL is not needed for DSI
v2: Rebase due to added DSI PLL assertion patch.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For DSI, we need to be asserting DSI PLL, not DPLL.
This is a somewhat stopgap implementation. It's slightly ugly to have to
pass the dsi parameter to intel_enable_pipe().
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2:
- Grab dpio_lock mutex in vlv_enable_dsi_pll().
- Add and call vlv_disable_dsi_pll().
v3: Mostly based on Ville's review comments.
- Only pipe A has DSI PLL lock bit.
- Add more of CCK REG bit definitions for DSI PLL.
- Make tables static.
- Move clock gating out of the clock calculation functions.
- DSI PLL LDO power gating.
- Put alternative MNP from table calc behind #ifdef.
v4: s/CKK/CLK/ in the CCK REG bit definitions (Ville).
Signed-off-by: ymohanma <yogesh.mohan.marimuthu@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This does not include any panel specific sub-encoders yet.
v2: Fix fixed mode handling (Daniel)
v3: Mostly based on Ville's review comments.
- Fix MIPI_HS_TX_TIMEOUT.
- DPI_ENABLE only for video mode.
- Drop ULPS usage for now, use DEVICE_READY only.
- Set MIPI_INIT_COUNT based on txclkesc.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Rebase due to register bit definition change.
v3: Mostly based on Ville's review comments.
- Use size_t for length all around.
- Reuse dsi_vc_send_short in dsi_vc_send_long.
- Remove stale/incorrect comments.
- Reverse special packet sent interrupt check.
- Use DSI controller regs for reading, not adapter.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The sub-encoder model is copied from DVO.
v2: Add attached_connector to struct intel_dsi.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add definitions for VLV MIPI DSI registers.
v2: Small fixes per Ville's review comments.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Add comment this is pipe A only (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For GPIO NC, CCK, CCU, and GPS CORE.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A follow-on to the update of the LLC coherency logic is that we can rely
on the LLC being coherent with the CS for rewriting batchbuffers
irrespective of their cache domain. (This should have no effect
currently as all the batch buffers are expected to be I915_CACHE_LLC and
so using the cpu relocation path anyway.)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The important bugfix here is that we must not unlink the vma when
we keep it around as a placeholder for the execbuf code. Since then we
won't find it again when execbuf gets interrupt and restarted and
create a 2nd vma. And since the code as-is isn't fit yet to deal with
more than one vma, hilarity ensues.
Specifically the dma map/unmap of the sg table isn't adjusted for
multiple vmas yet and will blow up like this:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
IP: [<ffffffffa008fb37>] i915_gem_gtt_finish_object+0x73/0xc8 [i915]
PGD 56bb5067 PUD ad3dd067 PMD 0
Oops: 0000 [#1] SMP
Modules linked in: tcp_lp ppdev parport_pc lp parport ipv6 dm_mod dcdbas snd_hda_codec_hdmi pcspkr snd_hda_codec_realtek serio_raw i2c_i801 iTCO_wdt iTCO_vendor_support snd_hda_intel snd_hda_codec lpc_ich snd_hwdep mfd_core snd_pcm snd_page_alloc snd_timer snd soundcore acpi_cpufreq i915 video button drm_kms_helper drm mperf freq_table
CPU: 1 PID: 16650 Comm: fbo-maxsize Not tainted 3.11.0-rc4_nightlytop_d93f59_debug_20130814_+ #6957
Hardware name: Dell Inc. OptiPlex 9010/03JR84, BIOS A01 05/04/2012
task: ffff8800563b3f00 ti: ffff88004bdf4000 task.ti: ffff88004bdf4000
RIP: 0010:[<ffffffffa008fb37>] [<ffffffffa008fb37>] i915_gem_gtt_finish_object+0x73/0xc8 [i915]
RSP: 0018:ffff88004bdf5958 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff8801135e0000 RCX: ffff8800ad3bf8e0
RDX: ffff8800ad3bf8e0 RSI: 0000000000000000 RDI: ffff8801007ee780
RBP: ffff88004bdf5978 R08: ffff8800ad3bf8e0 R09: 0000000000000000
R10: ffffffff86ca1810 R11: ffff880036a17101 R12: ffff8801007ee780
R13: 0000000000018001 R14: ffff880118c4e000 R15: ffff8801007ee780
FS: 00007f401a0ce740(0000) GS:ffff88011e280000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000008 CR3: 000000005635c000 CR4: 00000000001407e0
Stack:
ffff8801007ee780 ffff88005c253180 0000000000018000 ffff8801135e0000
ffff88004bdf59a8 ffffffffa0088e55 0000000000000011 ffff8801007eec00
0000000000018000 ffff880036a17101 ffff88004bdf5a08 ffffffffa0089026
Call Trace:
[<ffffffffa0088e55>] i915_vma_unbind+0xdf/0x1ab [i915]
[<ffffffffa0089026>] __i915_gem_shrink+0x105/0x177 [i915]
[<ffffffffa0089452>] i915_gem_object_get_pages_gtt+0x108/0x309 [i915]
[<ffffffffa0085ba9>] i915_gem_object_get_pages+0x61/0x90 [i915]
[<ffffffffa008f22b>] ? gen6_ppgtt_insert_entries+0x103/0x125 [i915]
[<ffffffffa008a113>] i915_gem_object_pin+0x1fa/0x5df [i915]
[<ffffffffa008cdfe>] i915_gem_execbuffer_reserve_object.isra.6+0x8d/0x1bc [i915]
[<ffffffffa008d156>] i915_gem_execbuffer_reserve+0x229/0x367 [i915]
[<ffffffffa008dbf6>] i915_gem_do_execbuffer.isra.12+0x4dc/0xf3a [i915]
[<ffffffff810fc823>] ? might_fault+0x40/0x90
[<ffffffffa008eb89>] i915_gem_execbuffer2+0x187/0x222 [i915]
[<ffffffffa000971c>] drm_ioctl+0x308/0x442 [drm]
[<ffffffffa008ea02>] ? i915_gem_execbuffer+0x3ae/0x3ae [i915]
[<ffffffff817db156>] ? __do_page_fault+0x3dd/0x481
[<ffffffff8112fdba>] vfs_ioctl+0x26/0x39
[<ffffffff811306a2>] do_vfs_ioctl+0x40e/0x451
[<ffffffff817deda7>] ? sysret_check+0x1b/0x56
[<ffffffff8113073c>] SyS_ioctl+0x57/0x87
[<ffffffff8135bbfe>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[<ffffffff817ded82>] system_call_fastpath+0x16/0x1b
Code: 48 c7 c6 84 30 0e a0 31 c0 e8 d0 e9 f7 ff bf c6 a7 00 00 e8 07 af 2c e1 41 f6 84 24 03 01 00 00 10 75 44 49 8b 84 24 08 01 00 00 <8b> 50 08 48 8b 30 49 8b 86 b0 04 00 00 48 89 c7 48 81 c7 98 00
RIP [<ffffffffa008fb37>] i915_gem_gtt_finish_object+0x73/0xc8 [i915]
RSP <ffff88004bdf5958>
CR2: 0000000000000008
As a consequence we need to change the "only one vma for now" check in
vma_unbind - since vma_destroy isn't always called the obj->vma_list
might not be empty. Instead check that the vma list is singular at the
beginning of vma_unbind. This is also more symmetric with bind_to_vm.
This fixes the igt/gem_evict_everything|alignment testcases.
v2:
- Add a paranoid WARN to mark_free in the eviction code to make sure
we never try to evict a vma used by the execbuf code right now.
- Move the check for a temporary execbuf vma into vma_destroy -
otherwise the failure path cleanup in bind_to_vm will blow up.
Our first attempting at fixing this was
commit 1be81a2f2cfd8789a627401d470423358fba2d76
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Aug 20 12:56:40 2013 +0100
drm/i915: Don't destroy the vma placeholder during execbuffer reservation
Squash with this when merging!
v3: Improvements suggested in Chris' review:
- Move the WARN_ON in vma_destroy that checks for vmas with an drm_mm
allocation before the early return.
- Bail out if we hit the WARN in mark_free to hopefully make the
kernel survive for long enough to capture it.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <ben@bwidawsk.net>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=68298
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=68171
Tested-by: lu hua <huax.lu@intel.com> (v2)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The execbuffer handle and exec_link were moved from the object into the
vma. As the vma may be unbound and destroyed whilst attempting to
reserve the execbuffer objects (either through a forced unbind to fix up
a misalignment or through an evict-everything call) we need to prevent
the free of the i915_vma itself. Otherwise not only is the list of
objects to reserve corrupt, but we continue to reference stale vma
entries.
Fixes kernel crash with i-g-t/gem_evict_everything
This regression has been introduced in
commit 04038a515d6eda6dd0857c0ade0b3950d372f4c0
Author: Ben Widawsky <ben@bwidawsk.net>
AuthorDate: Wed Aug 14 11:38:36 2013 +0200
drm/i915: Convert execbuf code to use vmas
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
References: http://www.spinics.net/lists/intel-gfx/msg32038.html
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=68298
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In the execbuf code we don't clean up any vmas which ended up not
getting bound for code simplicity. To make sure that we don't end up
creating multiple vma for the same vm kill the somewhat dangerous
vma_create function and inline it into lookup_or_create.
This is just a safety measure to prevent surprises in the future.
Also update the somewhat confused comment in the execbuf code and
clarify what kind of magic is going on with a new one.
v2: Keep the function separate as requested by Chris. But give it a __
prefix for paranoia and move it tighter together with the other vma
stuff.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <ben@bwidawsk.net>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In order to transition more of our code over to using a VMA instead of
an <OBJ, VM> pair - we must have the vma accessible at execbuf time. Up
until now, we've only had a VMA when actually binding an object.
The previous patch helped handle the distinction on bound vs. unbound.
This patch will help us catch leaks, and other issues before we actually
shuffle a bunch of stuff around.
This attempts to convert all the execbuf code to speak in vmas. Since
the execbuf code is very self contained it was a nice isolated
conversion.
The meat of the code is about turning eb_objects into eb_vma, and then
wiring up the rest of the code to use vmas instead of obj, vm pairs.
Unfortunately, to do this, we must move the exec_list link from the obj
structure. This list is reused in the eviction code, so we must also
modify the eviction code to make this work.
WARNING: This patch makes an already hotly profiled path slower. The cost is
unavoidable. In reply to this mail, I will attach the extra data.
v2: Release table lock early, and two a 2 phase vma lookup to avoid
having to use a GFP_ATOMIC. (Chris)
v3: s/obj_exec_list/obj_exec_link/
Updates to address
commit 6d2b888569
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed Aug 7 18:30:54 2013 +0100
drm/i915: List objects allocated from stolen memory in debugfs
v4: Use obj = vma->obj for neatness in some places (Chris)
need_reloc_mappable() should return false if ppgtt (Chris)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Split out prep patches. Also remove a FIXME comment which is
now taken care of.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The dpll actually runs at the port clock so we don't need
to multiply it again with the pixel multiplier to get the
adjusted_mode.clock. This is in contrast to the ironlake
pixel clock readout code which uses the fdi dotclock: That
one does _not_ run with multiplied pixels.
This issue goes back to the original clock readout code added
in
commit f1f644dc66
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Thu Jun 27 00:39:25 2013 +0300
drm/i915: get mode clock when reading the pipe config v9
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
