Need to drm_vblank_get/put() the crtc involved in a
pending pageflip, or we might not get vblank irqs and
updates of vblank counts and timestamps for pageflip
events and flip completion.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
The blob does not seem to write at that place for my NVAC, though it
does for my NV96, agreeing with what is done in the if/else structure
below. I guess someone forgot to remove the line when the if/else was
put in place.
Signed-off-by: Pierre Moreau <pierre.morrow@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The specified stride was not correct, resulting in erases overlapping
and part of the zcull regions being not erased at all.
Signed-off-by: Pierre Moreau <pierre.morrow@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes (at least) PTHERM accesses timing out at higher clock speeds.
Values and registers taken from what the binary driver does.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
display rework fixes lots of displayport issues.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6: (43 commits)
drm/nouveau/disp/dp: fix tmds passthrough on dp connector
drm/nouveau/dp: probe dpcd to determine connectedness
drm/nv50-: trigger update after all connectors disabled
drm/nv50-: prepare for attaching a SOR to multiple heads
drm/gf119-/disp: fix debug output on update failure
drm/nouveau/disp/dp: make use of postcursor when its available
drm/g94-/disp/dp: take max pullup value across all lanes
drm/nouveau/bios/dp: parse lane postcursor data
drm/nouveau/dp: fix support for dpms
drm/nouveau: register a drm_dp_aux channel for each dp connector
drm/g94-/disp: add method to power-off dp lanes
drm/nouveau/disp/dp: maintain link in response to hpd signal
drm/g94-/disp: bash and wait for something after changing lane power regs
drm/nouveau/disp/dp: split link config/power into two steps
drm/nv50/disp: train PIOR-attached DP from second supervisor
drm/nouveau/disp/dp: make use of existing output data for link training
drm/gf119/disp: start removing direct vbios parsing from supervisor
drm/nv50/disp: start removing direct vbios parsing from supervisor
drm/nouveau/disp/dp: maintain receiver caps in response to hpd signal
drm/nouveau/disp/dp: create subclass for dp outputs
...
We were sending the necessary state changes to unset the mode, but
never actually hit the big GO button unless another modeset happens
afterwards.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
SOR_PWR has no effect to power-off DP links, unlike other SOR protocols.
Instead, on the source side, we cut power to the lanes after having put
the sink into D3. Link training takes care of everything required to
bring it back again.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This previously worked for the most part due to userspace doing a
modeset in response to HPD interrupts. This will allow us to
properly handle cases where sync is lost for other reasons, or if
userspace isn't caring.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This will, at some point, be used to replace various bits and pieces of
code doing direct bios parsing. For now, it'll just be used for some
DP improvements.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There's also provisions to allow a pad to be locked with a specific
routing, for an indefinite period of time. This will be used in
future patches.
The G94+ pad driver will now also power-down pads when not required.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This was a half-finished hack before, just enough to handle the shared
aux/i2c pad thing on G94 and up.
We got lucky with locking etc up until now, as this was (generally) all
protected by the DRM mode_config lock. It's about to become a lot more
likely to hit the races.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Re-uses the implementation's accessor functions rather than requiring
and init/fini implementation for each chipset.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
