The new phy driver attempts to select a driver from another subsystem,
but that fails when the NVMEM subsystem is disabled:
WARNING: unmet direct dependencies detected for NVMEM_MTK_EFUSE
Depends on [n]: NVMEM [=n] && (ARCH_MEDIATEK [=n] || COMPILE_TEST [=y]) && HAS_IOMEM [=y]
Selected by [y]:
- MEDIATEK_GE_SOC_PHY [=y] && NETDEVICES [=y] && PHYLIB [=y] && (ARM64 && ARCH_MEDIATEK [=n] || COMPILE_TEST [=y])
I could not see an actual compile time dependency, so presumably this
is only needed for for working correctly but not technically a dependency
on that particular nvmem driver implementation, so it would likely
be safe to remove the select for compile testing.
To keep the spirit of the original 'select', just replace this with a
'depends on' that ensures that the driver will work but does not get in
the way of build testing.
Fixes: 98c485eaf5 ("net: phy: add driver for MediaTek SoC built-in GE PHYs")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20230616093009.3511692-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rahul Rameshbabu says:
====================
ptp .adjphase cleanups
The goal of this patch series is to improve documentation of .adjphase, add
a new callback .getmaxphase to enable advertising the max phase offset a
device PHC can support, and support invoking .adjphase from the testptp
kselftest.
Changes:
v2->v1:
* Removes arbitrary rule that the PHC servo must restore the frequency
to the value used in the last .adjfine call if any other PHC
operation is used after a .adjphase operation.
* Removes a macro introduced in v1 for adding PTP sysfs device
attribute nodes using a callback for populating the data.
Link: https://lore.kernel.org/netdev/20230120160609.19160723@kernel.org/
Link: https://lore.kernel.org/netdev/20230510205306.136766-1-rrameshbabu@nvidia.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a function that advertises a maximum offset of zero supported by
ptp_clock_info .adjphase in the OCP null ptp implementation.
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jonathan Lemon <jonathan.lemon@gmail.com>
Cc: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Advertise the maximum offset the .adjphase callback is capable of
supporting in nanoseconds for IDT devices.
Refactor the negation of the offset stored in the register to be after the
boundary check of the offset value rather than before. Boundary check based
on the intended value rather than its device-specific representation.
Depend on ptp_clock_adjtime for handling out-of-range offsets.
ptp_clock_adjtime returns -ERANGE instead of clamping out-of-range offsets.
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Min Li <min.li.xe@renesas.com>
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Advertise the maximum offset the .adjphase callback is capable of
supporting in nanoseconds for IDT ClockMatrix devices. Depend on
ptp_clock_adjtime for handling out-of-range offsets. ptp_clock_adjtime
returns -ERANGE instead of clamping out-of-range offsets.
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Vincent Cheng <vincent.cheng.xh@renesas.com>
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement .getmaxphase callback of ptp_clock_info in mlx5 driver. No longer
do a range check in .adjphase callback implementation. Handled by the ptp
stack.
Cc: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enables advertisement of the maximum offset supported by the phase control
functionality of PHCs. The callback is used to return an error if an offset
not supported by the PHC is used in ADJ_OFFSET. The ioctls
PTP_CLOCK_GETCAPS and PTP_CLOCK_GETCAPS2 now advertise the maximum offset a
PHC's phase control functionality is capable of supporting. Introduce new
sysfs node, max_phase_adjustment.
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Maciek Machnikowski <maciek@machnikowski.net>
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Invoke clock_adjtime syscall with tx.modes set with ADJ_OFFSET when testptp
is invoked with a phase adjustment offset value. Support seconds and
nanoseconds for the offset value.
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Maciek Machnikowski <maciek@machnikowski.net>
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use existing NSEC_PER_SEC declaration in place of hardcoded magic numbers.
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Maciek Machnikowski <maciek@machnikowski.net>
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx5_core driver has implemented ptp clock driver functionality but
lacked documentation about the PTP devices. This patch adds information
about the Mellanox device family.
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
.adjphase expects a PHC to use an internal servo algorithm to correct the
provided phase offset target in the callback. Implementation of the
internal servo algorithm are defined by the individual devices.
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kuniyuki Iwashima says:
====================
ipv6: Random cleanup for Extension Header.
This series (1) cleans up pskb_may_pull() in some functions, where needed
data are already pulled by their caller, (2) removes redundant multicast
test, and (3) optimises reload timing of the header.
====================
Link: https://lore.kernel.org/r/20230614230107.22301-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ipv6_destopt_rcv() and ipv6_parse_hopopts() pulls these data
- Hop-by-Hop/Destination Options Header : 8
- Hdr Ext Len : skb_transport_header(skb)[1] << 3
and calls ip6_parse_tlv(), so it need not check if skb_headlen() is less
than skb_transport_offset(skb) + (skb_transport_header(skb)[1] << 3).
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We need not reload hdr in ipv6_srh_rcv() unless we call
pskb_expand_head().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ipv6_rthdr_rcv() pulls these data
- Segment Routing Header : 8
- Hdr Ext Len : skb_transport_header(skb)[1] << 3
needed by ipv6_srh_rcv(), so pskb_pull() in ipv6_srh_rcv() never
fails and can be replaced with skb_pull().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ipv6_rpl_srh_rcv() checks if ipv6_hdr(skb)->daddr or ohdr->rpl_segaddr[i]
is the multicast address with ipv6_addr_type().
We have the same check for ipv6_hdr(skb)->daddr in ipv6_rthdr_rcv(), so we
need not recheck it in ipv6_rpl_srh_rcv().
Also, we should use ipv6_addr_is_multicast() for ohdr->rpl_segaddr[i]
instead of ipv6_addr_type().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As Eric Dumazet pointed out [0], ipv6_rthdr_rcv() pulls these data
- Segment Routing Header : 8
- Hdr Ext Len : skb_transport_header(skb)[1] << 3
needed by ipv6_rpl_srh_rcv(). We can remove pskb_may_pull() and
replace pskb_pull() with skb_pull() in ipv6_rpl_srh_rcv().
Link: https://lore.kernel.org/netdev/CANn89iLboLwLrHXeHJucAqBkEL_S0rJFog68t7wwwXO-aNf5Mg@mail.gmail.com/ [0]
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
1) Added a new event handler to firmware sync reset, which is used to
support firmware sync reset flow on smart NIC. Adding this new stage to
the flow enables the firmware to ensure host PFs unload before ECPFs
unload, to avoid race of PFs recovery.
2) Debugfs for mlx5 eswitch bridge offloads
3) Added two new counters for vport stats
4) Minor Fixups and cleanups for net-next branch
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmSMsbEACgkQSD+KveBX
+j6BAwgAyiZWqA8VEabjJtJNh30Ghfi5OkheAvJmPkd9UlM04EPw4x1dZ/z/jBnU
piBixrs0ou92ZF//Ph1vlf0Jae/YdfKdNcm/FEydspHZC0C2QqeNpDDWl0z3STqB
leBiFPjjBgqYWZWGwgaVlGOyzglTTu5DilkKVy1Ohf7j50P0FppViOsvQle3pAqO
UUXITN8si2AK/03JBJQNIulyyVP+EN9/+d8ZVZagKgurB9Qim9lUbZCerXacEUGV
M/XxYd+pwSAMh3TYlt2x1jv1aSpVwPzIolidJTjUd4gaImi40dw36kNP5BcoSMfr
QEaB1NMv4zfAwiZ7XaXY6/l5wqTjOg==
=vYKY
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2023-06-16' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
mlx5-updates-2023-06-16
1) Added a new event handler to firmware sync reset, which is used to
support firmware sync reset flow on smart NIC. Adding this new stage to
the flow enables the firmware to ensure host PFs unload before ECPFs
unload, to avoid race of PFs recovery.
2) Debugfs for mlx5 eswitch bridge offloads
3) Added two new counters for vport stats
4) Minor Fixups and cleanups for net-next branch
Signed-off-by: David S. Miller <davem@davemloft.net>
The double ifdefs (one for the variable declaration and
one around the code) are quite aesthetically displeasing.
Factor this code out into a helper for easier wrapping.
This will become even more ugly when another skb ext
comparison is added in the future.
The resulting machine code looks the same, the compiler
seems to try to use %rax more and some blocks more around
but I haven't spotted minor differences.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_regulator_get_enable_optional() instead of hand writing it. It
saves some line of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mention that the interrupt line is just asserted for a random period of
time, not the entire time.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When af_alg_sendmsg() calls extract_iter_to_sg(), it passes MAX_SGL_ENTS as
the maximum number of elements that may be written to, but some of the
elements may already have been used (as recorded in sgl->cur), so
extract_iter_to_sg() may end up overrunning the scatterlist.
Fix this to limit the number of elements to "MAX_SGL_ENTS - sgl->cur".
Note: It probably makes sense in future to alter the behaviour of
extract_iter_to_sg() to stop if "sgtable->nents >= sg_max" instead, but
this is a smaller fix for now.
The bug causes errors looking something like:
BUG: KASAN: slab-out-of-bounds in sg_assign_page include/linux/scatterlist.h:109 [inline]
BUG: KASAN: slab-out-of-bounds in sg_set_page include/linux/scatterlist.h:139 [inline]
BUG: KASAN: slab-out-of-bounds in extract_bvec_to_sg lib/scatterlist.c:1183 [inline]
BUG: KASAN: slab-out-of-bounds in extract_iter_to_sg lib/scatterlist.c:1352 [inline]
BUG: KASAN: slab-out-of-bounds in extract_iter_to_sg+0x17a6/0x1960 lib/scatterlist.c:1339
Fixes: bf63e250c4 ("crypto: af_alg: Support MSG_SPLICE_PAGES")
Reported-by: syzbot+6efc50cc1f8d718d6cb7@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/000000000000b2585a05fdeb8379@google.com/
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: syzbot+6efc50cc1f8d718d6cb7@syzkaller.appspotmail.com
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: Jens Axboe <axboe@kernel.dk>
cc: Matthew Wilcox <willy@infradead.org>
cc: linux-crypto@vger.kernel.org
cc: netdev@vger.kernel.org
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per-VMA locking allows us to lock a struct vm_area_struct without
taking the process-wide mmap lock in read mode.
Consider a process workload where the mmap lock is taken constantly in
write mode. In this scenario, all zerocopy receives are periodically
blocked during that period of time - though in principle, the memory
ranges being used by TCP are not touched by the operations that need
the mmap write lock. This results in performance degradation.
Now consider another workload where the mmap lock is never taken in
write mode, but there are many TCP connections using receive zerocopy
that are concurrently receiving. These connections all take the mmap
lock in read mode, but this does induce a lot of contention and atomic
ops for this process-wide lock. This results in additional CPU
overhead caused by contending on the cache line for this lock.
However, with per-vma locking, both of these problems can be avoided.
As a test, I ran an RPC-style request/response workload with 4KB
payloads and receive zerocopy enabled, with 100 simultaneous TCP
connections. I measured perf cycles within the
find_tcp_vma/mmap_read_lock/mmap_read_unlock codepath, with and
without per-vma locking enabled.
When using process-wide mmap semaphore read locking, about 1% of
measured perf cycles were within this path. With per-VMA locking, this
value dropped to about 0.45%.
Signed-off-by: Arjun Roy <arjunroy@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under certain circumstances, the tcp receive buffer memory limit
set by autotuning (sk_rcvbuf) is increased due to incoming data
packets as a result of the window not closing when it should be.
This can result in the receive buffer growing all the way up to
tcp_rmem[2], even for tcp sessions with a low BDP.
To reproduce: Connect a TCP session with the receiver doing
nothing and the sender sending small packets (an infinite loop
of socket send() with 4 bytes of payload with a sleep of 1 ms
in between each send()). This will cause the tcp receive buffer
to grow all the way up to tcp_rmem[2].
As a result, a host can have individual tcp sessions with receive
buffers of size tcp_rmem[2], and the host itself can reach tcp_mem
limits, causing the host to go into tcp memory pressure mode.
The fundamental issue is the relationship between the granularity
of the window scaling factor and the number of byte ACKed back
to the sender. This problem has previously been identified in
RFC 7323, appendix F [1].
The Linux kernel currently adheres to never shrinking the window.
In addition to the overallocation of memory mentioned above, the
current behavior is functionally incorrect, because once tcp_rmem[2]
is reached when no remediations remain (i.e. tcp collapse fails to
free up any more memory and there are no packets to prune from the
out-of-order queue), the receiver will drop in-window packets
resulting in retransmissions and an eventual timeout of the tcp
session. A receive buffer full condition should instead result
in a zero window and an indefinite wait.
In practice, this problem is largely hidden for most flows. It
is not applicable to mice flows. Elephant flows can send data
fast enough to "overrun" the sk_rcvbuf limit (in a single ACK),
triggering a zero window.
But this problem does show up for other types of flows. Examples
are websockets and other type of flows that send small amounts of
data spaced apart slightly in time. In these cases, we directly
encounter the problem described in [1].
RFC 7323, section 2.4 [2], says there are instances when a retracted
window can be offered, and that TCP implementations MUST ensure
that they handle a shrinking window, as specified in RFC 1122,
section 4.2.2.16 [3]. All prior RFCs on the topic of tcp window
management have made clear that sender must accept a shrunk window
from the receiver, including RFC 793 [4] and RFC 1323 [5].
This patch implements the functionality to shrink the tcp window
when necessary to keep the right edge within the memory limit by
autotuning (sk_rcvbuf). This new functionality is enabled with
the new sysctl: net.ipv4.tcp_shrink_window
Additional information can be found at:
https://blog.cloudflare.com/unbounded-memory-usage-by-tcp-for-receive-buffers-and-how-we-fixed-it/
[1] https://www.rfc-editor.org/rfc/rfc7323#appendix-F
[2] https://www.rfc-editor.org/rfc/rfc7323#section-2.4
[3] https://www.rfc-editor.org/rfc/rfc1122#page-91
[4] https://www.rfc-editor.org/rfc/rfc793
[5] https://www.rfc-editor.org/rfc/rfc1323
Signed-off-by: Mike Freemon <mfreemon@cloudflare.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current mctp_newroute() contains two exactly same check against
rtm->rtm_type
static int mctp_newroute(...)
{
...
if (rtm->rtm_type != RTN_UNICAST) { // (1)
NL_SET_ERR_MSG(extack, "rtm_type must be RTN_UNICAST");
return -EINVAL;
}
...
if (rtm->rtm_type != RTN_UNICAST) // (2)
return -EINVAL;
...
}
This commits removes the (2) check as it is redundant.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Acked-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20230615152240.1749428-1-linma@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
kcm_write_msgs() calls unreserve_psock() to release its hold on the
underlying TCP socket if it has run out of things to transmit, but if we
have nothing in the write queue on entry (e.g. because someone did a
zero-length sendmsg), we don't actually go into the transmission loop and
as a consequence don't call reserve_psock().
Fix this by skipping the call to unreserve_psock() if we didn't reserve a
psock.
Fixes: c31a25e1db ("kcm: Send multiple frags in one sendmsg()")
Reported-by: syzbot+dd1339599f1840e4cc65@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/000000000000a61ffe05fe0c3d08@google.com/
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: syzbot+dd1339599f1840e4cc65@syzkaller.appspotmail.com
cc: Tom Herbert <tom@herbertland.com>
cc: Tom Herbert <tom@quantonium.net>
cc: Jens Axboe <axboe@kernel.dk>
cc: Matthew Wilcox <willy@infradead.org>
Link: https://lore.kernel.org/r/20787.1686828722@warthog.procyon.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
"ecpu" field in struct mlx5_sf_table is not used anywhere. Remove it.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Separate the event API defined in the generic mlx5.h header into
a dedicated header. And remove the TODO comment in commit
69c1280b1f ("net/mlx5: Device events, Use async events chain").
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
This change is needed to use EC VFs with metadata based steering.
There was an assumption that vport was equal to function ID. That's
not the case for EC VF functions. Adjust to function ID and set the
ec_vf_function bit accordingly.
Fixes: 9ac0b12824 ("net/mlx5: Update vport caps query/set for EC VFs")
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The last value is not set correctly. This results in representors not
being created for all EC VFs when the base value is higher than 0.
Fixes: a7719b29a8 ("net/mlx5: Add management of EC VF vports")
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add counter for number of unicast, multicast and broadcast packets/
octets that were loopback.
Signed-off-by: Or Har-Toov <ohartoov@nvidia.com>
Reviewed-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add needed HW bits for querying local loopback counter and the
HCA capability for it.
Signed-off-by: Or Har-Toov <ohartoov@nvidia.com>
Reviewed-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The msglvl support was implemented using the mlx5e_dbg() macro which is
rarely used in the driver, and is not very useful when you can just use
dynamic debug instead.
Remove mlx5e_dbg() and convert its usages to netdev_dbg().
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
These else statement blocks are redundant since the if block already
jumps to the function abort label.
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Following patch requires access to additional data in bridge net_device.
Pass the whole structure down the stack instead of adding necessary fields
as function arguments one-by-one.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Following patch in series uses the new directory for bridge FDB debugfs.
The new directory is intended for all future eswitch-specific debugfs
files.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Added a new event handler to firmware sync reset, which is used to
support firmware sync reset flow on smart NIC. Adding this new stage to
the flow enables the firmware to ensure host PFs unload before ECPFs
unload, to avoid race of PFs recovery.
If firmware sends sync_reset_unload event to driver the driver should
unload and close all HW resources of the function. Once the driver
finishes unloading part, it can't get any more events from firmware as
event queues are closed, so it polls the reset state field to know when
to continue to next stage of the sync reset flow.
Added capability bit for supporting sync_reset_unload event.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The Default Timeout Register (DTOR) provides timeout values to driver
for flows that are device dependent. Zero value for DTOR entry is not
valid and should not be used. In case of reading zero value from DTOR,
the driver should use the hard coded SW default value instead.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Expose new timoueout in Default Timeouts Register to be used on sync
reset flow running on smart NIC. In this flow the driver should know how
much time to wait from getting unload request till firmware will ask the
PF to continue to next stage of the flow.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Verify at reset_request stage that PF is capable to do reset_now. In
case PF is not capable, notify the firmware that the sync reset can not
happen and so firmware will abort the sync reset at early stage and will
not send reset_now event to any PF.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Splicing to SOCK_RAW sockets may set MSG_SPLICE_PAGES, but in such a case,
__ip_append_data() will call skb_splice_from_iter() to access the 'from'
data, assuming it to point to a msghdr struct with an iter, instead of
using the provided getfrag function to access it.
In the case of raw_sendmsg(), however, this is not the case and 'from' will
point to a raw_frag_vec struct and raw_getfrag() will be the frag-getting
function. A similar issue may occur with rawv6_sendmsg().
Fix this by ignoring MSG_SPLICE_PAGES if getfrag != ip_generic_getfrag as
ip_generic_getfrag() expects "from" to be a msghdr*, but the other getfrags
don't. Note that this will prevent MSG_SPLICE_PAGES from being effective
for udplite.
This likely affects ping sockets too. udplite looks like it should be okay
as it expects "from" to be a msghdr.
Signed-off-by: David Howells <dhowells@redhat.com>
Reported-by: syzbot+d8486855ef44506fd675@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/000000000000ae4cbf05fdeb8349@google.com/
Fixes: 2dc334f1a6 ("splice, net: Use sendmsg(MSG_SPLICE_PAGES) rather than ->sendpage()")
Tested-by: syzbot+d8486855ef44506fd675@syzkaller.appspotmail.com
cc: David Ahern <dsahern@kernel.org>
cc: Jens Axboe <axboe@kernel.dk>
cc: Matthew Wilcox <willy@infradead.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/1410156.1686729856@warthog.procyon.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Functions efx_tc_netdev_event and efx_tc_netevent_event do not exist
in that case as object files tc_bindings.o and tc_encap_actions.o
are not built, so the calls to them from ef100_netdev_event and
ef100_netevent_event cause link errors.
Wrap the corresponding header files (tc_bindings.h, tc_encap_actions.h)
with #if IS_ENABLED(CONFIG_SFC_SRIOV), and add an #else with static
inline stubs for these two functions.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202306102026.ISK5JfUQ-lkp@intel.com/
Fixes: 7e5e7d8000 ("sfc: neighbour lookup for TC encap action offload")
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_ETHERNET=m or CONFIG_FDDI=m, lcs.s has build errors or
warnings:
../drivers/s390/net/lcs.c:40:2: error: #error Cannot compile lcs.c without some net devices switched on.
40 | #error Cannot compile lcs.c without some net devices switched on.
../drivers/s390/net/lcs.c: In function 'lcs_startlan_auto':
../drivers/s390/net/lcs.c:1601:13: warning: unused variable 'rc' [-Wunused-variable]
1601 | int rc;
Solve this by using IS_ENABLED(CONFIG_symbol) instead of ifdef
CONFIG_symbol. The latter only works for builtin (=y) values
while IS_ENABLED() works for builtin or modular values.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Alexandra Winter <wintera@linux.ibm.com>
Cc: Wenjia Zhang <wenjia@linux.ibm.com>
Cc: linux-s390@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement 64 bit per cpu stats to fix the overflow of netdev->stats
on 32 bit platforms. To simplify the code, we use net core
pcpu_sw_netstats infrastructure. One small drawback is some memory
overhead because litex uses just one queue, but we allocate the
counters per cpu.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Gabriel Somlo <gsomlo@gmail.com>
Link: https://lore.kernel.org/r/20230614162035.300-1-jszhang@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
