Adding eswitch statistics support. User can get
whole eswitch stats or stats of func belong to that eswitch.
Added:
o command to get statistics of eswitch and function.
o sysfs support to export eswitch and func statatistics.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Loopback not supported for virtual function.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix maximum and minmum bandwith value.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o NPAR configuration which is programmed in fw, need to
restore after fw recovery.
o Update version to 5.0.7
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pci error recovery support added.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver checks TSO capability from FW before enabling it.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following changes are made:
1.Obtain capabilities of Nic partition.
2.Configure tx bandwidth of particular Nic partition.
3.Configure the eswitch for setting port mirroring, enable mac
learning, promiscous mode.
Signed-off-by: Rajesh K Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After destroying recv ctx, context state remain same.
Fix it by marking as FREED.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Offload tx timeout recovery to fw recovery func(check_health).
In check_health, first check health of device, if it its ok, then
do tx timeout recovery otherwise device recovery.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we were allocating device resources during probe and
release them during remove.
Now alloc during interface up and release in interface down.
This helps in device performance, as it doesn't need to keep
track of inactive resources.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of delaying rcv handshake till interface comes up,
do it just after fw load.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to maintian separate state for alloced and freed skb.
This can be done by null check.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race between netif_stop_queue and netif_stopped_queue
check. So check once again if buffers are available to avoid race.
With above logic we can also get rid of tx lock in process_cmd_ring.
Signed-off-by: Rajesh K Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Earlier all poll routine can process rx and tx, But now
one poll routine to process rx + tx and other for rx only.
Last msix vector will be used for separate tx interrupt.
o This is supported from fw version 4.4.2.
o Bump version 5.0.5
Signed-off-by: Sony Chacko <schacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed the driver version number to 5.0.4
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was not detecting the presence of NIC partitioning capability of the
firmware properly. Now, it checks the eswitch set bit in the FW capabilities
register and accordingly sets the driver mode as NPAR capable or not.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for NIC functions that work in non privileged mode where these
functions are privileged to do IO only, the control operations are handled via
privileged functions.
Bumped up version number to 5.0.3.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following changes have been added to enable the adapter to work in
NIC partitioning mode where multiple PCI functions of an adapter port can
be configured to work as NIC functions. The first function that is enumerated on
the PCI bus assumes the role of management function which, besides being able
to do all the NIC functionality, can configure other NIC partitions. Other NIC
functions can be configured as privileged or non privileged functions.
Privileged function can not configure other NIC functions but can do all the
NIC functionality including any firmware initialization, chip reset etc. Non
privileged functions can do only basic IO. For chip reset etc, it depends on the
privilege or management function.
1. Added code to determine PCI function number independent of kernel API.
2. Added Driver - FW version 2.0 support.
3. Changed producer and consumer register offset calculation.
4. Added management and privileged operation modes for npar functions. A module
parameter has been added to control it.
5. Added support for configuring the eswitch in the adapter.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing register defines which are not used by Qlgoic CNA device.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ever driver changes the device state, it should write
pci-func number and timestamp in debug registers.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci-func class can be other than ethernet in Qlogic CNA device.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Warn user if IDC version mismatch with different class of drivers.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LRO ring, cut-thru mode and specific fw version are not
valid to Qlogic CNA device.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Window register is not per pci-func, so caching can
result in expected result.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update version to indicate IDC(fw recovery) changes.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added additional driver statistics to track errors in rcv/tx path.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add debug print in driver, can be tuned by ethtool msg level
callback.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o USE/Read IDC defined timeout value from ROM.
o While resetting chip, don't wait for other pci-func to respond,
more than reset_ack_timeo seconds,
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the access by tools for hardware queue engine and handle it
separately than other block registers, otherwise incorrect data
is returned.
Signed-off-by: Dhananjay Phadke <dhananjay.phadke@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Statistics added for lro/lso bytes, count for tx stop queue and
wake queue and skb alloc failure count.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Loopback test (offline) added in ethtool self test.
o Set device in loopback mode
o Send packets
o Process receive packets in qlcnic_process_rcv_ring_diag()
o Compare packets
o Reset device in normal mode.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interrupt test (offline) added in ethtool self test.
Register a temporary interrupt handler and then send command to fw
to raise an interrupt.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support of device identification by blinking LED for specified time.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added missing identifier that distinguishes between
FCOE/ISCSI/ETHERNET functions.
Signed-off-by: Rajesh K Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o 1G/10G Ethernet Driver for Qlgic QLE8240 and QLE8242 CNA devices.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
