We should check for the reception of an ACK after transmitting each
data byte. The address send has been correctly checking this, but the
data write byte state should have also been checking for these failures.
As part of the same fix, we remove the ACK checking from the receive
path where it should not have been checking for an ACK which our hardware
was sending.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Dhaval Giani reported this warning during cpu hotplug stress-tests:
| On running kernel compiles in parallel with cpu hotplug:
|
| WARNING: at arch/x86/kernel/smp.c:118
| native_smp_send_reschedule+0x21/0x36()
| Modules linked in:
| Pid: 27483, comm: cc1 Not tainted 2.6.26-rc7 #1
| [...]
| [<c0110355>] native_smp_send_reschedule+0x21/0x36
| [<c014fe8f>] force_quiescent_state+0x47/0x57
| [<c014fef0>] call_rcu+0x51/0x6d
| [<c01713b3>] __fput+0x130/0x158
| [<c0171231>] fput+0x17/0x19
| [<c016fd99>] filp_close+0x4d/0x57
| [<c016fdff>] sys_close+0x5c/0x97
IMHO the warning is a spurious one.
cpu_online_map is updated by the _cpu_down() using stop_machine_run().
Since force_quiescent_state is invoked from irqs disabled section,
stop_machine_run() won't be executing while a cpu is executing
force_quiescent_state(). Hence the cpu_online_map is stable while we're
in the irq disabled section.
However, a cpu might have been offlined _just_ before we disabled irqs
while entering force_quiescent_state(). And rcu subsystem might not yet
have handled the CPU_DEAD notification, leading to the offlined cpu's
bit being set in the rcp->cpumask.
Hence cpumask = (rcp->cpumask & cpu_online_map) to prevent sending
smp_reschedule() to an offlined CPU.
Here's the timeline:
CPU_A CPU_B
--------------------------------------------------------------
cpu_down(): .
. .
. .
stop_machine(): /* disables preemption, .
* and irqs */ .
. .
. .
take_cpu_down(); .
. .
. .
. .
cpu_disable(); /*this removes cpu .
*from cpu_online_map .
*/ .
. .
. .
restart_machine(); /* enables irqs */ .
------WINDOW DURING WHICH rcp->cpumask is stale ---------------
. call_rcu();
. /* disables irqs here */
. .force_quiescent_state();
.CPU_DEAD: .for_each_cpu(rcp->cpumask)
. . smp_send_reschedule();
. .
. . WARN_ON() for offlined CPU!
.
.
.
rcu_cpu_notify:
.
-------- WINDOW ENDS ------------------------------------------
rcu_offline_cpu() /* Which calls cpu_quiet()
* which removes
* cpu from rcp->cpumask.
*/
If a new batch was started just before calling stop_machine_run(), the
"tobe-offlined" cpu is still present in rcp-cpumask.
During a cpu-offline, from take_cpu_down(), we queue an rt-prio idle
task as the next task to be picked by the scheduler. We also call
cpu_disable() which will disable any further interrupts and remove the
cpu's bit from the cpu_online_map.
Once the stop_machine_run() successfully calls take_cpu_down(), it calls
schedule(). That's the last time a schedule is called on the offlined
cpu, and hence the last time when rdp->passed_quiesc will be set to 1
through rcu_qsctr_inc().
But the cpu_quiet() will be on this cpu will be called only when the
next RCU_SOFTIRQ occurs on this CPU. So at this time, the offlined CPU
is still set in rcp->cpumask.
Now coming back to the idle_task which truely offlines the CPU, it does
check for a pending RCU and raises the softirq, since it will find
rdp->passed_quiesc to be 0 in this case. However, since the cpu is
offline I am not sure if the softirq will trigger on the CPU.
Even if it doesn't the rcu_offline_cpu() will find that rcp->completed
is not the same as rcp->cur, which means that our cpu could be holding
up the grace period progression. Hence we call cpu_quiet() and move
ahead.
But because of the window explained in the timeline, we could still have
a call_rcu() before the RCU subsystem executes it's CPU_DEAD
notification, and we send smp_send_reschedule() to offlined cpu while
trying to force the quiescent states. The appended patch adds comments
and prevents checking for offlined cpu everytime.
cpu_online_map is updated by the _cpu_down() using stop_machine_run().
Since force_quiescent_state is invoked from irqs disabled section,
stop_machine_run() won't be executing while a cpu is executing
force_quiescent_state(). Hence the cpu_online_map is stable while we're
in the irq disabled section.
Reported-by: Dhaval Giani <dhaval@linux.vnet.ibm.com>
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Acked-by: Dhaval Giani <dhaval@linux.vnet.ibm.com>
Cc: Dipankar Sarma <dipankar@in.ibm.com>
Cc: laijs@cn.fujitsu.com
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Rusty Russel <rusty@rustcorp.com.au>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fsync_buffers_list() and sync_dirty_buffer() both issue async writes and
then immediately wait on them. Conceptually, that makes them sync writes
and we should treat them as such so that the IO schedulers can handle
them appropriately.
This patch fixes a write starvation issue that Lin Ming reported, where
xx is stuck for more than 2 minutes because of a large number of
synchronous IO in the system:
INFO: task kjournald:20558 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this
message.
kjournald D ffff810010820978 6712 20558 2
ffff81022ddb1d10 0000000000000046 ffff81022e7baa10 ffffffff803ba6f2
ffff81022ecd0000 ffff8101e6dc9160 ffff81022ecd0348 000000008048b6cb
0000000000000086 ffff81022c4e8d30 0000000000000000 ffffffff80247537
Call Trace:
[<ffffffff803ba6f2>] kobject_get+0x12/0x17
[<ffffffff80247537>] getnstimeofday+0x2f/0x83
[<ffffffff8029c1ac>] sync_buffer+0x0/0x3f
[<ffffffff8066d195>] io_schedule+0x5d/0x9f
[<ffffffff8029c1e7>] sync_buffer+0x3b/0x3f
[<ffffffff8066d3f0>] __wait_on_bit+0x40/0x6f
[<ffffffff8029c1ac>] sync_buffer+0x0/0x3f
[<ffffffff8066d48b>] out_of_line_wait_on_bit+0x6c/0x78
[<ffffffff80243909>] wake_bit_function+0x0/0x23
[<ffffffff8029e3ad>] sync_dirty_buffer+0x98/0xcb
[<ffffffff8030056b>] journal_commit_transaction+0x97d/0xcb6
[<ffffffff8023a676>] lock_timer_base+0x26/0x4b
[<ffffffff8030300a>] kjournald+0xc1/0x1fb
[<ffffffff802438db>] autoremove_wake_function+0x0/0x2e
[<ffffffff80302f49>] kjournald+0x0/0x1fb
[<ffffffff802437bb>] kthread+0x47/0x74
[<ffffffff8022de51>] schedule_tail+0x28/0x5d
[<ffffffff8020cac8>] child_rip+0xa/0x12
[<ffffffff80243774>] kthread+0x0/0x74
[<ffffffff8020cabe>] child_rip+0x0/0x12
Lin Ming confirms that this patch fixes the issue. I've run tests with
it for the past week and no ill effects have been observed, so I'm
proposing it for inclusion into 2.6.26.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
AS scheduler alternates between issuing read and write batches. It does
the batch switch only after all requests from the previous batch are
completed.
When switching to a write batch, if there is an on-going read request,
it waits for its completion and indicates its intention of switching by
setting ad->changed_batch and the new direction but does not update the
batch_expire_time for the new write batch which it does in the case of
no previous pending requests.
On completion of the read request, it sees that we were waiting for the
switch and schedules work for kblockd right away and resets the
ad->changed_data flag.
Now when kblockd enters dispatch_request where it is expected to pick
up a write request, it in turn ends the write batch because the
batch_expire_timer was not updated and shows the expire timestamp for
the previous batch.
This results in the write starvation for all the cases where there is
the intention for switching to a write batch, but there is a previous
in-flight read request and the batch gets reverted to a read_batch
right away.
This also holds true in the reverse case (switching from a write batch
to a read batch with an in-flight write request).
I've checked that this bug exists on 2.6.11, 2.6.18, 2.6.24 and
linux-2.6-block git HEAD. I've tested the fix on x86 platforms with
SCSI drives where the driver asks for the next request while a current
request is in-flight.
This patch is based off linux-2.6-block git HEAD.
Bug reproduction:
A simple scenario which reproduces this bug is:
- dd if=/dev/hda3 of=/dev/null &
- lilo
The lilo takes forever to complete.
This can also be reproduced fairly easily with the earlier dd and
another test
program doing msync().
The example test program below should print out a message after every
iteration
but it simply hangs forever. With this bugfix it makes forward progress.
====
Example test program using msync() (thanks to suleiman AT google DOT
com)
inline uint64_t
rdtsc(void)
{
int64_t tsc;
__asm __volatile("rdtsc" : "=A" (tsc));
return (tsc);
}
int
main(int argc, char **argv)
{
struct stat st;
uint64_t e, s, t;
char *p, q;
long i;
int fd;
if (argc < 2) {
printf("Usage: %s <file>\n", argv[0]);
return (1);
}
if ((fd = open(argv[1], O_RDWR | O_NOATIME)) < 0)
err(1, "open");
if (fstat(fd, &st) < 0)
err(1, "fstat");
p = mmap(NULL, st.st_size, PROT_READ | PROT_WRITE,
MAP_SHARED, fd, 0);
t = 0;
for (i = 0; i < 1000; i++) {
*p = 0;
msync(p, 4096, MS_SYNC);
s = rdtsc();
*p = 0;
__asm __volatile(""::: "memory");
e = rdtsc();
if (argc > 2)
printf("%d: %lld cycles %jd %jd\n",
i, e - s, (intmax_t)s, (intmax_t)e);
t += e - s;
}
printf("average time: %lld cycles\n", t / 1000);
return (0);
}
Cc: <stable@kernel.org>
Acked-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
commit 4323838215
x86: change size of node ids from u8 to s16
set the range for NODES_SHIFT to 1..15.
The possible range is 1..9
Fixes Bugzilla #10726
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The symbol account_system_vtime is used by the kvm module but
not exported. This breaks building with CONFIG_VIRT_CPU_ACCOUNTING
and CONFIG_KVM=m.
Signed-off-by: Doug Chapman <doug.chapman@hp.com>
Acked-by: Hidetosho Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
On a system where there are no hot pluggable cpus "additional_cpus"
is still set to -1 at the point where we call per_cpu_scan_finalize().
If we didn't find an SRAT table and so pick the default "32" for the
number of cpus, when we get to:
high_cpu = min(high_cpu + reserve_cpus, NR_CPUS);
we will end up initializing for just 31 cpus ... and so we will
die horribly when bringing up cpu#32.
Problem introduced by: 2c6e6db41f
"Minimize per_cpu reservations."
Acked-by: Robin Holt <holt@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch cleans up HW RF-kill state machine.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes iwl4965_mac_start block until the uCode has been
completely loaded.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes iwl4965_mac_get_tsf, as this function does not
currently reports any actual value.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds module param 11n_disable to allow configuration of 11n
capabilities. The default value of this param is 11n enabled (value 0).
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch unites common settings of 4965 and 5000 hw params.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch avoids the user from bringing up the interface if RF-kill
doesn't allow radio.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch removes the sysfs interface from iwl3945 and uses
the rfkill subsystem instead.
Original patch by Adel, I fixed the patch to work it properly.
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes the driver, in IBSS mode, comply with TSF requirements
in 2 ways:
1. It notifies mac80211 of its TSF timestamp.
2. It uses the given timestamp in the beacon template to update the ucode.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a beacon timestamp to the beacon template used in IBSS
mode. This way the underlying driver can update its TSF accordingly.
According the spec station should adopt the highest TSF from an incoming
beacons in the cell.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch avoids unsetting STATUS_EXIT_PENDING in the middle of the
down flow.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes regression caused by
'iwlwifi: send ADD_STA before RXON with assoc bit' patch.
RXON associated wasn't IBSS flow.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the use of lq_ready, once used to sync between link
quality commands to avoid race conditions, but no longer needed as
bss_info_changed is in use.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves Rx aggregation functions into iwl-rx.c
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch sets the compressed BA handler for 5000. This allows the rate
scaling algorithm to take in count frames that were sent in AMPDUs.
The compressed BA handler has been moved to iwl-rx.c since it is common to
4965 and 5000.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The iwlwifi drivers go to great lengths to avoid passing packets to
mac80211 they think shouldn't go there, while mac80211 can (of course!)
handle them very well.
Especially in the case of duplicate packets this is interesting
because it's such a performance hog (especially for IBSS networks)
while mac80211 does that work on the side without much effort.
This patch removes all that and leaves only what is absolutely
necessary for the hardware.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves RX handlers to iwl-rx.c
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch avoids sending REPLY_REMOVE_ALL_STA in down flow, this avoids a
meaningless warning from being printed
On the way this patch also renames the the function to
iwl_clear_stations_table
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves RX stats flow to core modules, and moves temperature
calibration to handler since it is not needed in 5000.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in association flow. As soon as RXON with assoc bit
is sent, uCode expects to have an entry in its station table that describe
the AP. Receiving a beacon from an HT AP before sending ADD_STA results a
uCode error. This patch sends first the ADD_STA (bcast and bssid) and only
then RXON with assoc bit set
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds REPLY_TX_POWER_DBM_CMD to get_cmd_string.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch add uses of iwl_is_associated in places it is suitable in.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes the station table maintenance safer. Two flags are
maintained:
1) if station is present in driver
2) if station is present in uCode
This will allow us in the future to deal with more stations than the
firmware allows.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds eeprom version display into device/version sysfs file
/sys/class/net/wlanX/devices/version
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch configures uCode to use open loop tx power algorithm
via TX_POWER_DBM (0x98) host command.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch sets the rfkill state to RFKILL_STATE_HARD_BLOCKED when the
radio is killed by the hardware switch.
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the usage RFKILL_STATE_ON and uses
RFKILL_STATE_UNBLOCKED instead.
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes warning: unused variable in invoke_tx_handlers
when compiling without MAC80211_DEBUG option
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Provide MAC time, rate, channel, signal and noise.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't try to skip any headers in hostap_80211_header_parse(). We never
use that function for interfaces affected by local->monitor_type. Both
the master and the AP interface receive 802.11 frames without any
additional headers.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the rfkill deps for iwl4965/5000
and removes the input device usage.
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the duplicated parsing of information elements
in ieee80211_rx_bss_info and in ieee_rx_mgmt_beacon
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ester Kummer <ester.kummer@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old infrastructure was:
- the default algorithm is built into mac80211
- other algorithms get into their own modules
The implementation of this complicated scheme was horrible
(just look at net/mac80211/Makefile), and anyone adding a new
algorithm would most likely not get it right at his first attempt.
This patch therefore builds all enabled algorithms into the mac80211
module.
The user interface for the rate control algorithms changes as follows:
- first the user can choose which algorithms to enable (currently only
MAC80211_RC_PID is available)
- if more than one algorithm is enabled (currently not possible since
only one algorithm is present) the user then chooses the default one
Note:
- MAC80211_RC_PID is always enables for CONFIG_EMBEDDED=n
Technical changes:
- all selected algorithms get into the mac80211 module
- net/mac80211/Makefile can now become much less complicated
- support for rc80211_pid_algo.c being modular is no longer required
- this includes unexporting mesh_plink_broken
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the interval between the scan results and the last time a
beacon was received in the result of the scan.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch add spectrum capability and required information
elements to association request providing AP has requested it and
it is supported by the driver
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch introduces MAC80211_VERBOSE_SPECT_MGMT_DEBUG Kconfig option to
suppress Spectrum Management 802.11h related debug logs.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This driver supports video input devices compliant with the USB Video Class
specification. This means lots of currently manufactured webcams, and probably
most of the future ones.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch makes mac80211 refuse a WEP key whose length is not WEP40 nor
WEP104.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
