Add a helper to get the voltage state of CF sockets, where the voltage
sense pins are not wired up. Switch assabet and cerf to use this
helper.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
If an attempt to set a socket state returns an error, restore the
previous socket state. If restoring the previous socket state
fails, warn about this.
This allows us to have simple error handling in the socket state
configuration handlers - there is no need for every handler
implementation to manually undo the updates, which can be complex
when regulators are involved.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Add support to soc_common for controlling reset and bus enable GPIOs
from within the generic soc_common layer, rather than having
individual drivers having to perform this themselves.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Request the legacy card detect signal with the active low property and
remove our own negation of the detection value. This allows us to use
the firmware-defined polarities rather than hard-coding it into the
driver.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
If gpiod_to_irq() returns an invalid interrupt, we should not try to use
it as an interrupt number.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Use devm_gpio_request_one() to request the GPIOs so we can avoid
manual clean up these gpio resources.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Here are 2 small fixes, and one new device id, for 4.8-rc7
The fixes solve a build error that was reported in your tree for the
blackfin arch, and resolve an issue with a number of broken USB devices
that reported the wrong interval rate. Included here is also a new
device id for the usb-serial driver.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlfebRsPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfsp2/IAoMbG
oJUDt8spFWQS1DCbmfdWNNSnAJ4qNSYDvL5uYWH44DkEyHr+4MekDg==
=QA88
-----END PGP SIGNATURE-----
Merge tag 'usb-4.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are two small fixes, and one new device id, for 4.8-rc7
The fixes solve a build error that was reported in your tree for the
blackfin arch, and resolve an issue with a number of broken USB
devices that reported the wrong interval rate. Included here is also
a new device id for the usb-serial driver.
All have been in linux-next with no reported issues"
* tag 'usb-4.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: change bInterval default to 10 ms
usb: musb: Fix tusb6010 compile error on blackfin
USB: serial: simple: add support for another Infineon flashloader
Pull perf fixes from Thomas Gleixner:
"A couple of small fixes to x86 perf drivers:
- Measure L2 for HW_CACHE* events on AMD
- Fix the address filter handling in the intel/pt driver
- Handle the BTS disabling at the proper place"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/amd: Make HW_CACHE_REFERENCES and HW_CACHE_MISSES measure L2
perf/x86/intel/pt: Do validate the size of a kernel address filter
perf/x86/intel/pt: Fix kernel address filter's offset validation
perf/x86/intel/pt: Fix an off-by-one in address filter configuration
perf/x86/intel: Don't disable "intel_bts" around "intel" event batching
Pull SMP build fixlet from Thomas Gleixner:
"Add a missing include in cpuhotplug.h"
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpu/hotplug: Include linux/types.h in linux/cpuhotplug.h
Pull irq fixes from Thomas Gleixner:
"Two patches from Boris which address a potential deadlock in the atmel
irq chip driver"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/atmel-aic: Fix potential deadlock in ->xlate()
genirq: Provide irq_gc_{lock_irqsave,unlock_irqrestore}() helpers
Since commit acb2505d01 ("openrisc: fix copy_from_user()"),
copy_from_user() returns the number of bytes requested, not the
number of bytes not copied.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Fixes: acb2505d01 ("openrisc: fix copy_from_user()")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
avr32 builds fail with:
arch/avr32/kernel/built-in.o: In function `arch_ptrace':
(.text+0x650): undefined reference to `___copy_from_user'
arch/avr32/kernel/built-in.o:(___ksymtab+___copy_from_user+0x0): undefined
reference to `___copy_from_user'
kernel/built-in.o: In function `proc_doulongvec_ms_jiffies_minmax':
(.text+0x5dd8): undefined reference to `___copy_from_user'
kernel/built-in.o: In function `proc_dointvec_minmax_sysadmin':
sysctl.c:(.text+0x6174): undefined reference to `___copy_from_user'
kernel/built-in.o: In function `ptrace_has_cap':
ptrace.c:(.text+0x69c0): undefined reference to `___copy_from_user'
kernel/built-in.o:ptrace.c:(.text+0x6b90): more undefined references to
`___copy_from_user' follow
Fixes: 8630c32275 ("avr32: fix copy_from_user()")
Cc: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Havard Skinnemoen <hskinnemoen@gmail.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
... by turning it into what used to be multipages counterpart
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes for code merged this cycle:
- Fix restore of SPRs upon wake up from hypervisor state loss from Gautham R. Shenoy
- Fix the state of root PE from Gavin Shan
- Detach from PE on releasing PCI device from Gavin Shan
- Fix size of NUM_CPU_FTR_KEYS on 32-bit
- Fix missed TCE invalidations that should fallback to OPAL
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=MG5t
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.8-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Fixes for code merged this cycle:
- Fix restore of SPRs upon wake up from hypervisor state loss from
Gautham R Shenoy
- Fix the state of root PE from Gavin Shan
- Detach from PE on releasing PCI device from Gavin Shan
- Fix size of NUM_CPU_FTR_KEYS on 32-bit
- Fix missed TCE invalidations that should fallback to OPAL"
* tag 'powerpc-4.8-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/powernv/pci: Fix missed TCE invalidations that should fallback to OPAL
powerpc/powernv: Detach from PE on releasing PCI device
powerpc/powernv: Fix the state of root PE
powerpc/kernel: Fix size of NUM_CPU_FTR_KEYS on 32-bit
powerpc/powernv: Fix restore of SPRs upon wake up from hypervisor state loss
Pull cifs fixes from Steve French:
"Small set of cifs fixes"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
Move check for prefix path to within cifs_get_root()
Compare prepaths when comparing superblocks
Fix memory leaks in cifs_do_mount()
i915, vc4 and atmel.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JIcI
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-for-4.8-rc6' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Two sets of i915 fixes, one set of vc4 crasher fixes, and a couple of
atmel fixes.
Nothing too out there at this stage, though I think some people are
holidaying so it's been quiet enough"
* tag 'drm-fixes-for-4.8-rc6' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Ignore OpRegion panel type except on select machines
Revert "drm/i915/psr: Make idle_frames sensible again"
drm/i915: Restore lost "Initialized i915" welcome message
drm/vc4: mark vc4_bo_cache_purge() static
drm/i915: Add GEN7_PCODE_MIN_FREQ_TABLE_GT_RATIO_OUT_OF_RANGE to SNB
drm/i915: disable 48bit full PPGTT when vGPU is active
drm/i915: enable vGPU detection for all
drm/atmel-hlcdc: Make ->reset() implementation static
drm: atmel-hlcdc: Fix vertical scaling
drm/vc4: Allow some more signals to be packed with uniform resets.
drm/i915/dvo: Remove dangling call to drm_encoder_cleanup()
More annotations of tracepoints in the runtime PM framework to
prevent RCU from complaining when that code is invoked from the
idle path (Paul McKenney).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=ljAx
-----END PGP SIGNATURE-----
Merge tag 'pm-4.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"More annotations of tracepoints in the runtime PM framework to prevent
RCU from complaining when that code is invoked from the idle path
(Paul McKenney)"
* tag 'pm-4.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / runtime: Use _rcuidle for runtime suspend tracepoints
-----BEGIN PGP SIGNATURE-----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=2xbn
-----END PGP SIGNATURE-----
Merge tag 'drm-vc4-fixes-2016-09-14' of https://github.com/anholt/linux into drm-fixes
This pull request brings in a fix for crashes in X on VC4.
* tag 'drm-vc4-fixes-2016-09-14' of https://github.com/anholt/linux:
drm/vc4: mark vc4_bo_cache_purge() static
drm/vc4: Allow some more signals to be packed with uniform resets.
i915 fixes from Jani.
* tag 'drm-intel-fixes-2016-09-15' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Ignore OpRegion panel type except on select machines
Revert "drm/i915/psr: Make idle_frames sensible again"
drm/i915: Restore lost "Initialized i915" welcome message
- Various fixes to rdmavt, ipoib, mlx5, mlx4, rxe
-----BEGIN PGP SIGNATURE-----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=HC3X
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"Round three of 4.8 rc fixes.
This is likely the last rdma pull request this cycle. The new rxe
driver had a few issues (you probably saw the boot bot bug report) and
they should be addressed now. There are a couple other fixes here,
mainly mlx4. There are still two outstanding issues that need
resolved but I don't think their fix will make this kernel cycle.
Summary:
- Various fixes to rdmavt, ipoib, mlx5, mlx4, rxe"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/rdmavt: Don't vfree a kzalloc'ed memory region
IB/rxe: Fix kmem_cache leak
IB/rxe: Fix race condition between requester and completer
IB/rxe: Fix duplicate atomic request handling
IB/rxe: Fix kernel panic in udp_setup_tunnel
IB/mlx5: Set source mac address in FTE
IB/mlx5: Enable MAD_IFC commands for IB ports only
IB/mlx4: Diagnostic HW counters are not supported in slave mode
IB/mlx4: Use correct subnet-prefix in QP1 mads under SR-IOV
IB/mlx4: Fix code indentation in QP1 MAD flow
IB/mlx4: Fix incorrect MC join state bit-masking on SR-IOV
IB/ipoib: Don't allow MC joins during light MC flush
IB/rxe: fix GFP_KERNEL in spinlock context
Here are a couple of bugfixes for v4.8-rc. Most of them have
actually been around for a while this time but for some reason
didn't get applied early on. The shmobile regulator fix is the
only one that isn't completely obvious.
device tree changes:
- archtimer interrupts must be level triggered (multiple platforms)
- fix for USB and MMC clocks on STiH410
- fix split DT repository in case of raspberry-pi 3
- A new use of skeleton.dtsi on arm64 has crept in after that
was removed.
defconfig updates:
- xilinx vdma has a new Kconfig symbol name
- keystone requires CONFIG_NOP_USB_XCEIV since v4.8-rc1
code fixes:
- fix regulator quirk on shmobile
- suspend-to-ram regression on EXYNOS
maintainer updates:
- Javier Martinez Canillas is now a reviewer for Samsung EXYNOS
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tYAb
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Here are a couple of bugfixes for v4.8-rc.
Most of them have actually been around for a while this time but for
some reason didn't get applied early on. The shmobile regulator fix
is the only one that isn't completely obvious.
Device tree changes:
- archtimer interrupts must be level triggered (multiple platforms)
- fix for USB and MMC clocks on STiH410
- fix split DT repository in case of raspberry-pi 3
- a new use of skeleton.dtsi on arm64 has crept in after that was
removed.
defconfig updates:
- xilinx vdma has a new Kconfig symbol name
- keystone requires CONFIG_NOP_USB_XCEIV since v4.8-rc1
Code fixes:
- fix regulator quirk on shmobile
- suspend-to-ram regression on EXYNOS
Maintainer updates:
- Javier Martinez Canillas is now a reviewer for Samsung EXYNOS"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: keystone: defconfig: Fix USB configuration
arm64: dts: Fix broken architected timer interrupt trigger
ARM: multi_v7_defconfig: update XILINX_VDMA
ARM64: dts: bcm: Use a symlink to R-Pi dtsi files from arch=arm
ARM: dts: Remove use of skeleton.dtsi from bcm283x.dtsi
ARM: dts: STiH407-family: Provide interconnect clock for consumption in ST SDHCI
ARM: dts: STiH410: Handle interconnect clock required by EHCI/OHCI (USB)
ARM: shmobile: fix regulator quirk for Gen2
ARM: EXYNOS: Clear OF_POPULATED flag from PMU node in IRQ init callback
MAINTAINERS: Add myself as reviewer for Samsung Exynos support
Pull ARM fixes from Russell King:
"Most of this update are fixes primarily discovered from testing on the
older StrongARM 1110 and PXA systems, as a result of recent interest
from several people in these platforms:
- Locomo interrupt handling incorrectly stores the handler data in
the chip's private data slot: when Locomo is combined with an
interrupt controller who's chip uses the chip private data, this
leads to an oops.
- SA1111 was missing a call to clk_disable() to clean up after a
failed probe.
- SA1111 and PCMCIA suspend/resume was broken:
The PCMCIA "ds" layer was using the legacy bus suspend/resume
methods, which the core PM code is no longer calling as a result of
device_pm_check_callbacks() introduced in commit aa8e54b559
("PM / sleep: Go direct_complete if driver has no callbacks").
SA1111 was broken due to changes to PCMCIA which makes PCMCIA
suspend itself later than the SA1111 code expects, and resume
before the SA1111 code has initialised access to the pcmcia
sub-device.
- the default SA1111 interrupt mask polarity got messed up when it
was converted to use a dynamic interrupt base number for its
interrupts.
- fix platform_get_irq() error code propagation, which was causing
problems on platforms where the interrupt may not be available at
probe time in DT setups.
- fix the lack of clock to PCMCIA code on PXA platforms, which was
omitted in conversions of PXA to CCF.
- fix an oops in the PXA PCMCIA code caused by a previous commit not
realising that Lubbock is different from the rest of the PXA PCMCIA
drivers.
- ensure that SA1111 low-level PCMCIA drivers propagate their error
codes to the main probe function, rather than the driver silently
accepting a failure.
- fix the sa11xx debugfs reporting of timing information, which
always indicated zero due to the clock being a factor of 1000 out.
- fix the polarity of the status change signal reported from the
sockets.
Lastly, one ARM specific commit from Stefan Agner fixing the LPAE
cache attributes"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: pxa/lubbock: add pcmcia clock
ARM: locomo: fix locomo irq handling
ARM: 8612/1: LPAE: initialize cache policy correctly
ARM: sa1111: fix missing clk_disable()
ARM: sa1111: fix pcmcia suspend/resume
ARM: sa1111: fix pcmcia interrupt mask polarity
ARM: sa1111: fix error code propagation in sa1111_probe()
pcmcia: lubbock: fix sockets configuration
pcmcia: sa1111: fix propagation of lowlevel board init return code
pcmcia: soc_common: fix SS_STSCHG polarity
pcmcia: sa11xx_base: add units to the timing information
pcmcia: sa11xx_base: fix reporting of timing information
pcmcia: ds: fix suspend/resume
The userspace memory region 'mr' is allocated with kzalloc in
__rvt_alloc_mr however it is incorrectly being freed with vfree in
__rvt_free_mr. Fix this by using kfree to free it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
rxe_requester() is sending a pkt with rxe_xmit_packet() and
then calls rxe_update() to update the wqe and qp's psn values.
But sometimes the response is received before the requester
had time to update the wqe in which case the completer
acts on errornous wqe values.
This fix updates the wqe and qp before actually sending
the request and rolls back when xmit fails.
Fixes: 8700e3e7c4 ("Soft RoCE driver")
Signed-off-by: Yonatan Cohen <yonatanc@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When handling ack for atomic opcodes like "fetch&add"
or "cmp&swp", the method send_atomic_ack() saves the ack
before sending it, in case it gets lost and never reach the
requester. In which case the method duplicate_request()
will need to find it using the duplicated request.psn.
But send_atomic_ack() used a wrong psn value and thus
the above ack was never found.
This fix uses the ack.psn to locate the ack in case
its needed.
This fix also copies the ack packet to the skb's control buffer
since duplicate_request() will need it when calling rxe_xmit_packet()
Fixes: 8700e3e7c4 ("Soft RoCE driver")
Signed-off-by: Yonatan Cohen <yonatanc@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Set the source mac address in the FTE when L2 specification
is provided.
Fixes: 038d2ef875 ('IB/mlx5: Add flow steering support')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
MAD_IFC command is supported only for physical functions (PF)
and when physical port is IB. The proposed fix enforces it.
Fixes: d603c809ef ("IB/mlx5: Fix decision on using MAD_IFC")
Reported-by: David Chang <dchang@suse.com>
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Modify the mlx4_ib_diag_counters() to avoid the following error in the
hypervisor when the slave tries to query the hardware counters in SR-IOV
mode.
mlx4_core 0000:81:00.0: Unknown command:0x30 accepted from slave:1
Fixes: 3f85f2aaab ("IB/mlx4: Add diagnostic hardware counters")
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When sending QP1 MAD packets which use a GRH, the source GID
(which consists of the 64-bit subnet prefix, and the 64 bit port GUID)
must be included in the packet GRH.
For SR-IOV, a GID cache is used, since the source GID needs to be the
slave's source GID, and not the Hypervisor's GID. This cache also
included a subnet_prefix. Unfortunately, the subnet_prefix field in
the cache was never initialized (to the default subnet prefix 0xfe80::0).
As a result, this field remained all zeroes. Therefore, when SR-IOV
was active, all QP1 packets which included a GRH had a source GID
subnet prefix of all-zeroes.
However, the subnet-prefix should initially be 0xfe80::0 (the default
subnet prefix). In addition, if OpenSM modifies a port's subnet prefix,
the new subnet prefix must be used in the GRH when sending QP1 packets.
To fix this we now initialize the subnet prefix in the SR-IOV GID cache
to the default subnet prefix. We update the cached value if/when OpenSM
modifies the port's subnet prefix. We take this cached value when sending
QP1 packets when SR-IOV is active.
Note that the value is stored as an atomic64. This eliminates any need
for locking when the subnet prefix is being updated.
Note also that we depend on the FW generating the "port management change"
event for tracking subnet-prefix changes performed by OpenSM. If running
early FW (before 2.9.4630), subnet prefix changes will not be tracked (but
the default subnet prefix still will be stored in the cache; therefore
users who do not modify the subnet prefix will not have a problem).
IF there is a need for such tracking also for early FW, we will add that
capability in a subsequent patch.
Fixes: 1ffeb2eb8b ("IB/mlx4: SR-IOV IB context objects and proxy/tunnel SQP support")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The indentation in the QP1 GRH flow in procedure build_mlx_header is
really confusing. Fix it, in preparation for a commit which touches
this code.
Fixes: 1ffeb2eb8b ("IB/mlx4: SR-IOV IB context objects and proxy/tunnel SQP support")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Because of an incorrect bit-masking done on the join state bits, when
handling a join request we failed to detect a difference between the
group join state and the request join state when joining as send only
full member (0x8). This caused the MC join request not to be sent.
This issue is relevant only when SRIOV is enabled and SM supports
send only full member.
This fix separates scope bits and join states bits a nibble each.
Fixes: b9c5d6a643 ('IB/mlx4: Add multicast group (MCG) paravirtualization for SR-IOV')
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This fix solves a race between light flush and on the fly joins.
Light flush doesn't set the device to down and unset IPOIB_OPER_UP
flag, this means that if while flushing we have a MC join in progress
and the QP was attached to BC MGID we can have a mismatches when
re-attaching a QP to the BC MGID.
The light flush would set the broadcast group to NULL causing an on
the fly join to rejoin and reattach to the BC MCG as well as adding
the BC MGID to the multicast list. The flush process would later on
remove the BC MGID and detach it from the QP. On the next flush
the BC MGID is present in the multicast list but not found when trying
to detach it because of the previous double attach and single detach.
[18332.714265] ------------[ cut here ]------------
[18332.717775] WARNING: CPU: 6 PID: 3767 at drivers/infiniband/core/verbs.c:280 ib_dealloc_pd+0xff/0x120 [ib_core]
...
[18332.775198] Hardware name: Red Hat KVM, BIOS Bochs 01/01/2011
[18332.779411] 0000000000000000 ffff8800b50dfbb0 ffffffff813fed47 0000000000000000
[18332.784960] 0000000000000000 ffff8800b50dfbf0 ffffffff8109add1 0000011832f58300
[18332.790547] ffff880226a596c0 ffff880032482000 ffff880032482830 ffff880226a59280
[18332.796199] Call Trace:
[18332.798015] [<ffffffff813fed47>] dump_stack+0x63/0x8c
[18332.801831] [<ffffffff8109add1>] __warn+0xd1/0xf0
[18332.805403] [<ffffffff8109aebd>] warn_slowpath_null+0x1d/0x20
[18332.809706] [<ffffffffa025d90f>] ib_dealloc_pd+0xff/0x120 [ib_core]
[18332.814384] [<ffffffffa04f3d7c>] ipoib_transport_dev_cleanup+0xfc/0x1d0 [ib_ipoib]
[18332.820031] [<ffffffffa04ed648>] ipoib_ib_dev_cleanup+0x98/0x110 [ib_ipoib]
[18332.825220] [<ffffffffa04e62c8>] ipoib_dev_cleanup+0x2d8/0x550 [ib_ipoib]
[18332.830290] [<ffffffffa04e656f>] ipoib_uninit+0x2f/0x40 [ib_ipoib]
[18332.834911] [<ffffffff81772a8a>] rollback_registered_many+0x1aa/0x2c0
[18332.839741] [<ffffffff81772bd1>] rollback_registered+0x31/0x40
[18332.844091] [<ffffffff81773b18>] unregister_netdevice_queue+0x48/0x80
[18332.848880] [<ffffffffa04f489b>] ipoib_vlan_delete+0x1fb/0x290 [ib_ipoib]
[18332.853848] [<ffffffffa04df1cd>] delete_child+0x7d/0xf0 [ib_ipoib]
[18332.858474] [<ffffffff81520c08>] dev_attr_store+0x18/0x30
[18332.862510] [<ffffffff8127fe4a>] sysfs_kf_write+0x3a/0x50
[18332.866349] [<ffffffff8127f4e0>] kernfs_fop_write+0x120/0x170
[18332.870471] [<ffffffff81207198>] __vfs_write+0x28/0xe0
[18332.874152] [<ffffffff810e09bf>] ? percpu_down_read+0x1f/0x50
[18332.878274] [<ffffffff81208062>] vfs_write+0xa2/0x1a0
[18332.881896] [<ffffffff812093a6>] SyS_write+0x46/0xa0
[18332.885632] [<ffffffff810039b7>] do_syscall_64+0x57/0xb0
[18332.889709] [<ffffffff81883321>] entry_SYSCALL64_slow_path+0x25/0x25
[18332.894727] ---[ end trace 09ebbe31f831ef17 ]---
Fixes: ee1e2c82c2 ("IPoIB: Refresh paths instead of flushing them on SM change events")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There is skb_clone(skb, GFP_KERNEL) in spinlock context
in rxe_rcv_mcast_pkt().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
broke Suspend to RAM on Exynos boards due to lack of probing of
PMU (Power Management Unit) driver. Multiple drivers attach to
the PMU's DT node: irqchip, clock controller and PMU platform
driver for handling suspend. The new irqchip code marked the
PMU's DT node as OF_POPULATED but we need to attach to this
node also PMU platform driver.
2. Add Javier as additional reviewer for Exynos patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Ljgr
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into fixes
Pull "ARM: exynos: Fixes for v4.8, secound round" from Krzysztof Kozłowski:
1. A recent change in populating irqchip devices from Device Tree
broke Suspend to RAM on Exynos boards due to lack of probing of
PMU (Power Management Unit) driver. Multiple drivers attach to
the PMU's DT node: irqchip, clock controller and PMU platform
driver for handling suspend. The new irqchip code marked the
PMU's DT node as OF_POPULATED but we need to attach to this
node also PMU platform driver.
2. Add Javier as additional reviewer for Exynos patches.
* tag 'samsung-fixes-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: EXYNOS: Clear OF_POPULATED flag from PMU node in IRQ init callback
MAINTAINERS: Add myself as reviewer for Samsung Exynos support
Some full-speed mceusb infrared transceivers contain invalid endpoint
descriptors for their interrupt endpoints, with bInterval set to 0.
In the past they have worked out okay with the mceusb driver, because
the driver sets the bInterval field in the descriptor to 1,
overwriting whatever value may have been there before. However, this
approach was never sanctioned by the USB core, and in fact it does not
work with xHCI controllers, because they use the bInterval value that
was present when the configuration was installed.
Currently usbcore uses 32 ms as the default interval if the value in
the endpoint descriptor is invalid. It turns out that these IR
transceivers don't work properly unless the interval is set to 10 ms
or below. To work around this mceusb problem, this patch changes the
endpoint-descriptor parsing routine, making the default interval value
be 10 ms rather than 32 ms.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Wade Berrier <wberrier@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have CONFIG_BLACKFIN ifdef redefining all musb registers in
musb_regs.h and tusb6010.h is never included causing a build
error with blackfin-allmodconfig and COMPILE_TEST.
Let's fix the issue by not building tusb6010 if CONFIG_BLACKFIN
is selected.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the Intel PMU monitors the LLC when perf enables the
HW_CACHE_REFERENCES and HW_CACHE_MISSES events, these events monitor
L1 instruction cache fetches (0x0080) and instruction cache misses
(0x0081) on the AMD PMU.
This is extremely confusing when monitoring the same workload across
Intel and AMD machines, since parameters like,
$ perf stat -e cache-references,cache-misses
measure completely different things.
Instead, make the AMD PMU measure instruction/data cache and TLB fill
requests to the L2 and instruction/data cache and TLB misses in the L2
when HW_CACHE_REFERENCES and HW_CACHE_MISSES are enabled,
respectively. That way the events measure unified caches on both
platforms.
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1472044328-21302-1-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Right now, the kernel address filters in PT are prone to integer overflow
that may happen in adding filter's size to its offset to obtain the end
of the range. Such an overflow would also throw a #GP in the PT event
configuration path.
Fix this by explicitly validating the result of this calculation.
Reported-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: stable@vger.kernel.org # v4.7
Cc: stable@vger.kernel.org#v4.7
Cc: vince@deater.net
Link: http://lkml.kernel.org/r/20160915151352.21306-4-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The kernel_ip() filter is used mostly by the DS/LBR code to look at the
branch addresses, but Intel PT also uses it to validate the address
filter offsets for kernel addresses, for which it is not sufficient:
supplying something in bits 64:48 that's not a sign extension of the lower
address bits (like 0xf00d000000000000) throws a #GP.
This patch adds address validation for the user supplied kernel filters.
Reported-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: stable@vger.kernel.org # v4.7
Cc: stable@vger.kernel.org#v4.7
Cc: vince@deater.net
Link: http://lkml.kernel.org/r/20160915151352.21306-3-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
PT address filter configuration requires that a range is specified by
its first and last address, but at the moment we're obtaining the end
of the range by adding user specified size to its start, which is off
by one from what it actually needs to be.
Fix this and make sure that zero-sized filters don't pass the filter
validation.
Reported-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: stable@vger.kernel.org # v4.7
Cc: stable@vger.kernel.org#v4.7
Cc: vince@deater.net
Link: http://lkml.kernel.org/r/20160915151352.21306-2-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Further testing with false negatives suppressed by commit 293e2421fe
("rcu: Remove superfluous versions of rcu_read_lock_sched_held()")
identified a few more unprotected uses of RCU from the idle loop.
Because RCU actively ignores idle-loop code (for energy-efficiency
reasons, among other things), using RCU from the idle loop can result
in too-short grace periods, in turn resulting in arbitrary misbehavior.
The affected function is rpm_suspend().
The resulting lockdep-RCU splat is as follows:
------------------------------------------------------------------------
Warning from omap3
===============================
[ INFO: suspicious RCU usage. ]
4.6.0-rc5-next-20160426+ #1112 Not tainted
-------------------------------
include/trace/events/rpm.h:63 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
RCU used illegally from idle CPU!
rcu_scheduler_active = 1, debug_locks = 0
RCU used illegally from extended quiescent state!
1 lock held by swapper/0/0:
#0: (&(&dev->power.lock)->rlock){-.-...}, at: [<c052ee24>] __pm_runtime_suspend+0x54/0x84
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.6.0-rc5-next-20160426+ #1112
Hardware name: Generic OMAP36xx (Flattened Device Tree)
[<c0110308>] (unwind_backtrace) from [<c010c3a8>] (show_stack+0x10/0x14)
[<c010c3a8>] (show_stack) from [<c047fec8>] (dump_stack+0xb0/0xe4)
[<c047fec8>] (dump_stack) from [<c052d7b4>] (rpm_suspend+0x604/0x7e4)
[<c052d7b4>] (rpm_suspend) from [<c052ee34>] (__pm_runtime_suspend+0x64/0x84)
[<c052ee34>] (__pm_runtime_suspend) from [<c04bf3bc>] (omap2_gpio_prepare_for_idle+0x5c/0x70)
[<c04bf3bc>] (omap2_gpio_prepare_for_idle) from [<c01255e8>] (omap_sram_idle+0x140/0x244)
[<c01255e8>] (omap_sram_idle) from [<c0126b48>] (omap3_enter_idle_bm+0xfc/0x1ec)
[<c0126b48>] (omap3_enter_idle_bm) from [<c0601db8>] (cpuidle_enter_state+0x80/0x3d4)
[<c0601db8>] (cpuidle_enter_state) from [<c0183c74>] (cpu_startup_entry+0x198/0x3a0)
[<c0183c74>] (cpu_startup_entry) from [<c0b00c0c>] (start_kernel+0x354/0x3c8)
[<c0b00c0c>] (start_kernel) from [<8000807c>] (0x8000807c)
------------------------------------------------------------------------
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This ensures that do_mmap() won't implicitly make AIO memory mappings
executable if the READ_IMPLIES_EXEC personality flag is set. Such
behavior is problematic because the security_mmap_file LSM hook doesn't
catch this case, potentially permitting an attacker to bypass a W^X
policy enforced by SELinux.
I have tested the patch on my machine.
To test the behavior, compile and run this:
#define _GNU_SOURCE
#include <unistd.h>
#include <sys/personality.h>
#include <linux/aio_abi.h>
#include <err.h>
#include <stdlib.h>
#include <stdio.h>
#include <sys/syscall.h>
int main(void) {
personality(READ_IMPLIES_EXEC);
aio_context_t ctx = 0;
if (syscall(__NR_io_setup, 1, &ctx))
err(1, "io_setup");
char cmd[1000];
sprintf(cmd, "cat /proc/%d/maps | grep -F '/[aio]'",
(int)getpid());
system(cmd);
return 0;
}
In the output, "rw-s" is good, "rwxs" is bad.
Signed-off-by: Jann Horn <jann@thejh.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
