Marvell's Armada 370 Reference Design has a NAND flash, so enable it in
the devicetree and add the partitions as prepared in the factory images.
In order to skip the driver's custom device detection and use only ONFI
detection, the "marvell,keep-config" parameter is used. This is needed
because we have no support for setting the timings parameters yet.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that NAND controller support is available for Armada XP
(cb28e2537a: ARM: mvebu: Add support for NAND controller in
Armada 370/XP), this patch enables support for ReadyNAS 2120
and defines default partition layout as delivered by NETGEAR.
As described in similar commits 2be2bc39c6 (ARM: mvebu: Enable
NAND controller in Armada XP GP board) and d8c552dddf (ARM:
mvebu: Enable NAND controller in Armada 370 Mirabox),
"marvell,keep-config" parameter is used as current support does
not allow for setting of timing parameters yet.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that NAND controller support is available for Armada 370
(cb28e2537a: ARM: mvebu: Add support for NAND controller in
Armada 370/XP), this patch enables support for ReadyNAS 104 and
defines default partition layout as delivered by NETGEAR.
As described in similar commits 2be2bc39c6 (ARM: mvebu: Enable
NAND controller in Armada XP GP board) and d8c552dddf (ARM:
mvebu: Enable NAND controller in Armada 370 Mirabox),
"marvell,keep-config" parameter is used as current support does
not allow for setting of timing parameters yet.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that NAND controller support is available for Armada 370
(cb28e2537a: ARM: mvebu: Add support for NAND controller in
Armada 370/XP), this patch enables support for ReadyNAS 102 and
defines default partition layout as delivered by NETGEAR.
As described in similar commits 2be2bc39c6 (ARM: mvebu: Enable
NAND controller in Armada XP GP board) and d8c552dddf (ARM:
mvebu: Enable NAND controller in Armada 370 Mirabox),
"marvell,keep-config" parameter is used as current support does
not allow for setting of timing parameters yet.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Use GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW instead of 0 and 1.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Replace the numeric key value with a symbolic name from
<bt-bindings/input/input.h>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Almost all hardware parts of the NETGEAR ReadyNAS NV+ v2 ([1] for more
details) are supported by mainline kernel. The only missing elements in
provided .dts file are:
- the front LCD module (Winstar WINSTAR WH1602): driver development is
ongoing. This is the same LCD module as on ReadyNAS 104.
- the Macronix MX25L512 512Kbit SPI flash: no time to play with it yet.
The device is the big brother (4 vs 2 bay) of the ReadyNAS Duo v2. The
main differences are some additional LEDs for the disks, a Marvell
88SM4140 SATA Port multiplier (no driver required to access the disk)
and previously described LCD module. Otherwise, it shares the same SoC
(kirkwood 88F6282), RAM (256MB), NAND (128MB), RTC chip (Ricoh rs5c372a),
fan controller (GMT G762), XHCI controller (NEC/Renesas µPD720200).
[1]: http://natisbad.org/NAS5/
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
All hardware parts of the (mv78230 Armada XP based) NETGEAR ReadyNAS
2120 are supported by mainline kernel (USB 3.0 and eSATA rear ports,
USB 2.0 front port, Gigabit controller and PHYs for the two rear ports,
serial port, LEDs, Buttons, 88SE9170 SATA controllers, three G762 fan
controllers, G751 temperature sensor) except for:
- the Intersil ISL12057 I2C RTC Chip,
- the Armada NAND controller.
Support for both of those is currently work in progress and does not
prevent boot.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch provides some whitespace cleanup for NETGEAR
ReadyNAS Duo v2 and 102 .dts files:
- Fixed bad spaces
- Added some space between nodes to improve readability
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The patch does some cleanup work on NETGEAR ReadyNAS 104 .dts
file. Changes are listed below:
- Completed conversion from value to macros for GPIO voltage level
- Converted all numeric input key values to macros
- Fixed all node names and labels to use respectively '-' and '_'
- Made button names more explicit
- Changed order of included files from general to local
- Removed useless clocks and gpio-keys properties
- Document ethernet PHY (Marvell 88E1318) via a comment
- Made G762 clock node name unique by including g762 in it
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The patch does some cleanup work on NETGEAR ReadyNAS 102 .dts
file. Changes are listed below
- Added missing button mpp in pinctrl
- Converted from value to macros for GPIO voltage level
- Converted all numeric input key values to macros
- Added GPIO keys pins to pinctrl
- Made button names more explicit
- Document ethernet PHY (Marvell 88E1318) via a comment
- Made G762 clock node name unique by including g762 in it
- Fixed all node names and labels to use respectively '-' and '_'
- Changed order of included files from general to local
- Removed useless clocks and gpio-keys properties
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The patch does some cleanup work on NETGEAR ReadyNAS Duo v2 .dts
file. Changes are listed below:
- Converted from value to macros for GPIO voltage level
- Converted all numeric input key values to macros
- Made button names more explicit
- Document ethernet PHY (Marvell 88E1318) via a comment
- Added header for the file to describe content and author
- Made G762 clock node name unique by including g762 in it
- Fixed all node names and labels to use respectively '-' and '_'
- Changed order of included files from general to local
- Removed useless clocks and gpio-keys properties
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The RTC on Dove has an interrupt on the PMU interrupt controller.
Add this interrupt to the RTC node. Tested using the
"RTC Driver Test Example"
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Instantiate the PMU interrupt controller which Dove has.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Without that fix, at the end of the shutdown process, the board is
still powered (led glowing, fan running, ...).
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
NETGEAR ReadyNAS 104 has a NXP PCA9554 I2C to GPIO chip. Among the 8 GPIO
lines the chip makes available, four are used on the device to control
the SATA LEDs (the four remaining ones are used for SATA disk presence).
This patch adds DT entries for NXP PCA9554 and the four SATA GPIO LEDs.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Globalscale Guruplug has AW-GH381 WiFi/BT on sdio which is always
present and cannot be detected in any way. Therefore, mark the node
as non-removable instead of broken-cd. While at it, also put a note
about connected WiFi/BT chip above.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
SDIO controllers found on Marvell Kirkwood 6281/6282 SoCs require
pins to be muxed by pinctrl. As there is only one sane pinctrl
setting for this, provide default pinctrl properties to the controller
nodes.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch fixes a typo for device_type property of phy node.
This can work as of today but once a checks are added in generic code
this typo will stop phy from working.
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
This patch fixes a typo for device_type property of phy node.
This can work as of today but once a checks are added in generic code
this typo will stop phy from working.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada 370 Mirabox has a NAND flash, so enable it in the devicetree
and add the partitions as prepared in the factory images.
In order to skip the driver's custom device detection and use only
ONFI detection, the "marvell,keep-config" parameter is used.
This is needed because we have no support for setting the timings parameters yet.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada XP GP board has a NAND flash, so enable it in the devicetree.
In order to skip the driver's custom device detection and use only ONFI
detection, the "marvell,keep-config" parameter is used.
This is needed because we haven't support for setting the timings
parameters yet and must rely in bootloader's.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada 370 and Armada XP SoC have a NAND controller (aka NFCv2).
This commit adds support for it in Armada 370 and Armada XP SoC
common devicetree.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Change the file names given in the comments of the Sheevaplug
dts files to actually match the real file names.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Generally, power LEDs should indicate when power is applied, and go out
once power is removed. _Not_ annoy the developer with migraine-inducing
blinking reminicent of some badly animated television series designed to
sell sugar to children.
On a more serious note, most of these OS-specific properties aren't
necessary and should be removed. I left two that are legitimately tying
disk LEDs to disk activity. Other than that, we keep the state the
bootloader left them in until userspace changes the state via sysfs.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
A collection of small fixes in HD-audio quirks and runtime PM, ASoC
rcar, abs8500 and other codecs. Most of commits are for stable
kernels, too.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=zoMb
-----END PGP SIGNATURE-----
Merge tag 'sound-fix2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull second set of sound fixes from Takashi Iwai:
"A collection of small fixes in HD-audio quirks and runtime PM, ASoC
rcar, abs8500 and other codecs. Most of commits are for stable
kernels, too"
* tag 'sound-fix2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Set current_headset_type to ALC_HEADSET_TYPE_ENUM (janitorial)
ALSA: hda - Provide missing pin configs for VAIO with ALC260
ALSA: hda - Add headset quirk for Dell Inspiron 3135
ALSA: hda - Fix the headphone jack detection on Sony VAIO TX
ALSA: hda - Fix missing bass speaker on ASUS N550
ALSA: hda - Fix unbalanced runtime PM notification at resume
ASoC: arizona: Set FLL to free-run before disabling
ALSA: hda - A casual Dell Headset quirk
ASoC: rcar: fixup dma_async_issue_pending() timing
ASoC: rcar: off by one in rsnd_scu_set_route()
ASoC: wm5110: Add post SYSCLK register patch for rev D chip
ASoC: ab8500: Revert to using custom I/O functions
ALSA: hda - Also enable mute/micmute LED control for "Lenovo dock" fixup
ALSA: firewire-lib: include sound/asound.h to refer to snd_pcm_format_t
ALSA: hda - Select FW_LOADER from CONFIG_SND_HDA_CODEC_CA0132_DSP
ALSA: hda - Enable mute/mic-mute LEDs for more Thinkpads with Realtek codec
ASoC: rcar: fixup mod access before checking
Pull DRM fixes from Dave Airlie:
"I was going to leave this until post -rc1 but sysfs fixes broke
hotplug in userspace, so I had to fix it harder, otherwise a set of
pulls from intel, radeon and vmware,
The vmware/ttm changes are bit larger but since its early and they are
unlikely to break anything else I put them in, it lets vmware work
with dri3"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (36 commits)
drm/sysfs: fix hotplug regression since lifetime changes
drm/exynos: g2d: fix memory leak to userptr
drm/i915: Fix gen3 self-refresh watermarks
drm/ttm: Remove set_need_resched from the ttm fault handler
drm/ttm: Don't move non-existing data
drm/radeon: hook up backlight functions for CI and KV family.
drm/i915: Replicate BIOS eDP bpp clamping hack for hsw
drm/i915: Do not enable package C8 on unsupported hardware
drm/i915: Hold pc8 lock around toggling pc8.gpu_idle
drm/i915: encoder->get_config is no longer optional
drm/i915/tv: add ->get_config callback
drm/radeon/cik: Add macrotile mode array query
drm/radeon/cik: Return backend map information to userspace
drm/vmwgfx: Make vmwgfx dma buffers prime aware
drm/vmwgfx: Make surfaces prime-aware
drm/vmwgfx: Hook up the prime ioctls
drm/ttm: Add a minimal prime implementation for ttm base objects
drm/vmwgfx: Fix false lockdep warning
drm/ttm: Allow execbuf util reserves without ticket
drm/i915: restore the early forcewake cleanup
...
Pull SCSI target updates from Nicholas Bellinger:
"Things have been quiet this round with mostly bugfixes, percpu
conversions, and other minor iscsi-target conformance testing changes.
The highlights include:
- Add demo_mode_discovery attribute for iscsi-target (Thomas)
- Convert tcm_fc(FCoE) to use percpu-ida pre-allocation
- Add send completion interrupt coalescing for ib_isert
- Convert target-core to use percpu-refcounting for se_lun
- Fix mutex_trylock usage bug in iscsit_increment_maxcmdsn
- tcm_loop updates (Hannes)
- target-core ALUA cleanups + prep for v3.14 SCSI Referrals support (Hannes)
v3.14 is currently shaping to be a busy development cycle in target
land, with initial support for T10 Referrals and T10 DIF currently on
the roadmap"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (40 commits)
iscsi-target: chap auth shouldn't match username with trailing garbage
iscsi-target: fix extract_param to handle buffer length corner case
iscsi-target: Expose default_erl as TPG attribute
target_core_configfs: split up ALUA supported states
target_core_alua: Make supported states configurable
target_core_alua: Store supported ALUA states
target_core_alua: Rename ALUA_ACCESS_STATE_OPTIMIZED
target_core_alua: spellcheck
target core: rename (ex,im)plict -> (ex,im)plicit
percpu-refcount: Add percpu-refcount.o to obj-y
iscsi-target: Do not reject non-immediate CmdSNs exceeding MaxCmdSN
iscsi-target: Convert iscsi_session statistics to atomic_long_t
target: Convert se_device statistics to atomic_long_t
target: Fix delayed Task Aborted Status (TAS) handling bug
iscsi-target: Reject unsupported multi PDU text command sequence
ib_isert: Avoid duplicate iscsit_increment_maxcmdsn call
iscsi-target: Fix mutex_trylock usage in iscsit_increment_maxcmdsn
target: Core does not need blkdev.h
target: Pass through I/O topology for block backstores
iser-target: Avoid using FRMR for single dma entry requests
...
acpi_power_meter: Fix return value check from call to acpi_bus_get_device
nct6775: Fix/improve NCT6791 support
lm75: Add support for GMT G751
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=ObF6
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- acpi_power_meter: Fix return value check from call to
acpi_bus_get_device
- nct6775: Fix/improve NCT6791 support
- lm75: Add support for GMT G751
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (acpi_power_meter) Fix acpi_bus_get_device() return value check
hwmon: (nct6775) NCT6791 supports weight control only for CPUFAN
hwmon: (nct6775) Monitor additional temperature registers
hwmon: (lm75) Add support for GMT G751 chip
Pull networking fixes from David Miller:
1) Fix memory leaks and other issues in mwifiex driver, from Amitkumar
Karwar.
2) skb_segment() can choke on packets using frag lists, fix from
Herbert Xu with help from Eric Dumazet and others.
3) IPv4 output cached route instantiation properly handles races
involving two threads trying to install the same route, but we
forgot to propagate this logic to input routes as well. Fix from
Alexei Starovoitov.
4) Put protections in place to make sure that recvmsg() paths never
accidently copy uninitialized memory back into userspace and also
make sure that we never try to use more that sockaddr_storage for
building the on-kernel-stack copy of a sockaddr. Fixes from Hannes
Frederic Sowa.
5) R8152 driver transmit flow bug fixes from Hayes Wang.
6) Fix some minor fallouts from genetlink changes, from Johannes Berg
and Michael Opdenacker.
7) AF_PACKET sendmsg path can race with netdevice unregister notifier,
fix by using RCU to make sure the network device doesn't go away
from under us. Fix from Daniel Borkmann.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
gso: handle new frag_list of frags GRO packets
genetlink: fix genl_set_err() group ID
genetlink: fix genlmsg_multicast() bug
packet: fix use after free race in send path when dev is released
xen-netback: stop the VIF thread before unbinding IRQs
wimax: remove dead code
net/phy: Add the autocross feature for forced links on VSC82x4
net/phy: Add VSC8662 support
net/phy: Add VSC8574 support
net/phy: Add VSC8234 support
net: add BUG_ON if kernel advertises msg_namelen > sizeof(struct sockaddr_storage)
net: rework recvmsg handler msg_name and msg_namelen logic
bridge: flush br's address entry in fdb when remove the
net: core: Always propagate flag changes to interfaces
ipv4: fix race in concurrent ip_route_input_slow()
r8152: fix incorrect type in assignment
r8152: support stopping/waking tx queue
r8152: modify the tx flow
r8152: fix tx/rx memory overflow
netfilter: ebt_ip6: fix source and destination matching
...
Pull ARM fixes from Russell King:
"Some small fixes for this merge window, most of them quite self
explanatory - the biggest thing here is a fix for the ARMv7 LPAE
suspend/resume support"
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7894/1: kconfig: select GENERIC_CLOCKEVENTS if HAVE_ARM_ARCH_TIMER
ARM: 7893/1: bitops: only emit .arch_extension mp if CONFIG_SMP
ARM: 7892/1: Fix warning for V7M builds
ARM: 7888/1: seccomp: not compatible with ARM OABI
ARM: 7886/1: make OABI default to off
ARM: 7885/1: Save/Restore 64-bit TTBR registers on LPAE suspend/resume
ARM: 7884/1: mm: Fix ECC mem policy printk
ARM: 7883/1: fix mov to mvn conversion in case of 64 bit phys_addr_t and BE
ARM: 7882/1: mm: fix __phys_to_virt to work with 64 bit phys_addr_t in BE case
ARM: 7881/1: __fixup_smp read of SCU config should do byteswap in BE case
ARM: Fix nommu.c build warning
Pull aio fixes from Benjamin LaHaise.
* git://git.kvack.org/~bcrl/aio-next:
aio: nullify aio->ring_pages after freeing it
aio: prevent double free in ioctx_alloc
aio: Fix a trinity splat
Pull nfsd bugfixes from Bruce Fields:
"A couple nfsd bugfixes"
* 'for-3.13' of git://linux-nfs.org/~bfields/linux:
nfsd4: fix xdr decoding of large non-write compounds
nfsd: make sure to balance get/put_write_access
nfsd: split up nfsd_setattr
fixes a possible NULL pointer dereference, and the second one
resolves a reference counting issue in one of the lesser used paths
through atomic_open.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=aMoW
-----END PGP SIGNATURE-----
Merge tag 'gfs2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes
Pull GFS2 fixes from Steven Whitehouse:
"A couple of small, but important bug fixes for GFS2. The first one
fixes a possible NULL pointer dereference, and the second one resolves
a reference counting issue in one of the lesser used paths through
atomic_open"
* tag 'gfs2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes:
GFS2: Fix ref count bug relating to atomic_open
GFS2: fix potential NULL pointer dereference
Pull btrfs fixes from Chris Mason:
"Almost all of these are bug fixes. Dave Sterba's documentation update
is the big exception because he removed our promises to set any
machine running Btrfs on fire"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Documentation: filesystems: update btrfs tools section
Documentation: filesystems: add new btrfs mount options
btrfs: update kconfig help text
btrfs: fix bio_size_ok() for max_sectors > 0xffff
btrfs: Use trace condition for get_extent tracepoint
btrfs: fix typo in the log message
Btrfs: fix list delete warning when removing ordered root from the list
Btrfs: print bytenr instead of page pointer in check-int
Btrfs: remove dead codes from ctree.h
Btrfs: don't wait for ordered data outside desired range
Btrfs: fix lockdep error in async commit
Btrfs: avoid heavy operations in btrfs_commit_super
Btrfs: fix __btrfs_start_workers retval
Btrfs: disable online raid-repair on ro mounts
Btrfs: do not inc uncorrectable_errors counter on ro scrubs
Btrfs: only drop modified extents if we logged the whole inode
Btrfs: make sure to copy everything if we rename
Btrfs: don't BUG_ON() if we get an error walking backrefs
Here we have a performance fix for inode iversion, increased inode cluster size
for v5 superblock filesystems, a fix for error handling in
xfs_bmap_add_attrfork, and a MAINTAINERS update to add Dave.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=w0M3
-----END PGP SIGNATURE-----
Merge tag 'xfs-for-linus-v3.13-rc1-2' of git://oss.sgi.com/xfs/xfs
Pull second xfs update from Ben Myers:
"There are a couple of patches that I wasn't quite sure about in time
for our initial 3.13 pull request, a bugfix, and an update to add Dave
to MAINTAINERS:
Here we have a performance fix for inode iversion, increased inode
cluster size for v5 superblock filesystems, a fix for error handling
in xfs_bmap_add_attrfork, and a MAINTAINERS update to add Dave"
* tag 'xfs-for-linus-v3.13-rc1-2' of git://oss.sgi.com/xfs/xfs:
xfs: open code inc_inode_iversion when logging an inode
xfs: increase inode cluster size for v5 filesystems
xfs: fix unlock in xfs_bmap_add_attrfork
xfs: update maintainers
Pull SLAB changes from Pekka Enberg:
"The patches from Joonsoo Kim switch mm/slab.c to use 'struct page' for
slab internals similar to mm/slub.c. This reduces memory usage and
improves performance:
https://lkml.org/lkml/2013/10/16/155
Rest of the changes are bug fixes from various people"
* 'slab/next' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux: (21 commits)
mm, slub: fix the typo in mm/slub.c
mm, slub: fix the typo in include/linux/slub_def.h
slub: Handle NULL parameter in kmem_cache_flags
slab: replace non-existing 'struct freelist *' with 'void *'
slab: fix to calm down kmemleak warning
slub: proper kmemleak tracking if CONFIG_SLUB_DEBUG disabled
slab: rename slab_bufctl to slab_freelist
slab: remove useless statement for checking pfmemalloc
slab: use struct page for slab management
slab: replace free and inuse in struct slab with newly introduced active
slab: remove SLAB_LIMIT
slab: remove kmem_bufctl_t
slab: change the management method of free objects of the slab
slab: use __GFP_COMP flag for allocating slab pages
slab: use well-defined macro, virt_to_slab()
slab: overloading the RCU head over the LRU for RCU free
slab: remove cachep in struct slab_rcu
slab: remove nodeid in struct slab
slab: remove colouroff in struct slab
slab: change return type of kmem_getpages() to struct page
...
Pull third set of powerpc updates from Benjamin Herrenschmidt:
"This is a small collection of random bug fixes and a few improvements
of Oops output which I deemed valuable enough to include as well.
The fixes are essentially recent build breakage and regressions, and a
couple of older bugs such as the DTL log duplication, the EEH issue
with PCI_COMMAND_MASTER and the problem with small contexts passed to
get/set_context with VSX enabled"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/signals: Mark VSX not saved with small contexts
powerpc/pseries: Fix SMP=n build of rng.c
powerpc: Make cpu_to_chip_id() available when SMP=n
powerpc/vio: Fix a dma_mask issue of vio
powerpc: booke: Fix build failures
powerpc: ppc64 address space capped at 32TB, mmap randomisation disabled
powerpc: Only print PACATMSCRATCH in oops when TM is active
powerpc/pseries: Duplicate dtl entries sometimes sent to userspace
powerpc: Remove a few lines of oops output
powerpc: Print DAR and DSISR on machine check oopses
powerpc: Fix __get_user_pages_fast() irq handling
powerpc/eeh: More accurate log
powerpc/eeh: Enable PCI_COMMAND_MASTER for PCI bridges
current_headset_type should be of the HEADSET_TYPE enum, not the
HEADSET_MODE enum. Since ALC_HEADSET_TYPE_UNKNOWN and ALC_HEADSET_MODE_UNKNOWN
are both 0, this patch is just janitorial.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some models (or maybe depending on BIOS version) of Sony VAIO with
ALC260 give no proper pin configurations as default, resulting in the
non-working speaker, etc. Just provide the whole pin configurations
via a fixup.
Reported-by: Matthew Markus <mmarkus@hearit.co>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge patches from Andrew Morton:
"13 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: place page->pmd_huge_pte to right union
MAINTAINERS: add keyboard driver to Hyper-V file list
x86, mm: do not leak page->ptl for pmd page tables
ipc,shm: correct error return value in shmctl (SHM_UNLOCK)
mm, mempolicy: silence gcc warning
block/partitions/efi.c: fix bound check
ARM: drivers/rtc/rtc-at91rm9200.c: disable interrupts at shutdown
mm: hugetlbfs: fix hugetlbfs optimization
kernel: remove CONFIG_USE_GENERIC_SMP_HELPERS cleanly
ipc,shm: fix shm_file deletion races
mm: thp: give transparent hugepage code a separate copy_page
checkpatch: fix "Use of uninitialized value" warnings
configfs: fix race between dentry put and lookup
Pull security subsystem updates from James Morris:
"In this patchset, we finally get an SELinux update, with Paul Moore
taking over as maintainer of that code.
Also a significant update for the Keys subsystem, as well as
maintenance updates to Smack, IMA, TPM, and Apparmor"
and since I wanted to know more about the updates to key handling,
here's the explanation from David Howells on that:
"Okay. There are a number of separate bits. I'll go over the big bits
and the odd important other bit, most of the smaller bits are just
fixes and cleanups. If you want the small bits accounting for, I can
do that too.
(1) Keyring capacity expansion.
KEYS: Consolidate the concept of an 'index key' for key access
KEYS: Introduce a search context structure
KEYS: Search for auth-key by name rather than target key ID
Add a generic associative array implementation.
KEYS: Expand the capacity of a keyring
Several of the patches are providing an expansion of the capacity of a
keyring. Currently, the maximum size of a keyring payload is one page.
Subtract a small header and then divide up into pointers, that only gives
you ~500 pointers on an x86_64 box. However, since the NFS idmapper uses
a keyring to store ID mapping data, that has proven to be insufficient to
the cause.
Whatever data structure I use to handle the keyring payload, it can only
store pointers to keys, not the keys themselves because several keyrings
may point to a single key. This precludes inserting, say, and rb_node
struct into the key struct for this purpose.
I could make an rbtree of records such that each record has an rb_node
and a key pointer, but that would use four words of space per key stored
in the keyring. It would, however, be able to use much existing code.
I selected instead a non-rebalancing radix-tree type approach as that
could have a better space-used/key-pointer ratio. I could have used the
radix tree implementation that we already have and insert keys into it by
their serial numbers, but that means any sort of search must iterate over
the whole radix tree. Further, its nodes are a bit on the capacious side
for what I want - especially given that key serial numbers are randomly
allocated, thus leaving a lot of empty space in the tree.
So what I have is an associative array that internally is a radix-tree
with 16 pointers per node where the index key is constructed from the key
type pointer and the key description. This means that an exact lookup by
type+description is very fast as this tells us how to navigate directly to
the target key.
I made the data structure general in lib/assoc_array.c as far as it is
concerned, its index key is just a sequence of bits that leads to a
pointer. It's possible that someone else will be able to make use of it
also. FS-Cache might, for example.
(2) Mark keys as 'trusted' and keyrings as 'trusted only'.
KEYS: verify a certificate is signed by a 'trusted' key
KEYS: Make the system 'trusted' keyring viewable by userspace
KEYS: Add a 'trusted' flag and a 'trusted only' flag
KEYS: Separate the kernel signature checking keyring from module signing
These patches allow keys carrying asymmetric public keys to be marked as
being 'trusted' and allow keyrings to be marked as only permitting the
addition or linkage of trusted keys.
Keys loaded from hardware during kernel boot or compiled into the kernel
during build are marked as being trusted automatically. New keys can be
loaded at runtime with add_key(). They are checked against the system
keyring contents and if their signatures can be validated with keys that
are already marked trusted, then they are marked trusted also and can
thus be added into the master keyring.
Patches from Mimi Zohar make this usable with the IMA keyrings also.
(3) Remove the date checks on the key used to validate a module signature.
X.509: Remove certificate date checks
It's not reasonable to reject a signature just because the key that it was
generated with is no longer valid datewise - especially if the kernel
hasn't yet managed to set the system clock when the first module is
loaded - so just remove those checks.
(4) Make it simpler to deal with additional X.509 being loaded into the kernel.
KEYS: Load *.x509 files into kernel keyring
KEYS: Have make canonicalise the paths of the X.509 certs better to deduplicate
The builder of the kernel now just places files with the extension ".x509"
into the kernel source or build trees and they're concatenated by the
kernel build and stuffed into the appropriate section.
(5) Add support for userspace kerberos to use keyrings.
KEYS: Add per-user_namespace registers for persistent per-UID kerberos caches
KEYS: Implement a big key type that can save to tmpfs
Fedora went to, by default, storing kerberos tickets and tokens in tmpfs.
We looked at storing it in keyrings instead as that confers certain
advantages such as tickets being automatically deleted after a certain
amount of time and the ability for the kernel to get at these tokens more
easily.
To make this work, two things were needed:
(a) A way for the tickets to persist beyond the lifetime of all a user's
sessions so that cron-driven processes can still use them.
The problem is that a user's session keyrings are deleted when the
session that spawned them logs out and the user's user keyring is
deleted when the UID is deleted (typically when the last log out
happens), so neither of these places is suitable.
I've added a system keyring into which a 'persistent' keyring is
created for each UID on request. Each time a user requests their
persistent keyring, the expiry time on it is set anew. If the user
doesn't ask for it for, say, three days, the keyring is automatically
expired and garbage collected using the existing gc. All the kerberos
tokens it held are then also gc'd.
(b) A key type that can hold really big tickets (up to 1MB in size).
The problem is that Active Directory can return huge tickets with lots
of auxiliary data attached. We don't, however, want to eat up huge
tracts of unswappable kernel space for this, so if the ticket is
greater than a certain size, we create a swappable shmem file and dump
the contents in there and just live with the fact we then have an
inode and a dentry overhead. If the ticket is smaller than that, we
slap it in a kmalloc()'d buffer"
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (121 commits)
KEYS: Fix keyring content gc scanner
KEYS: Fix error handling in big_key instantiation
KEYS: Fix UID check in keyctl_get_persistent()
KEYS: The RSA public key algorithm needs to select MPILIB
ima: define '_ima' as a builtin 'trusted' keyring
ima: extend the measurement list to include the file signature
kernel/system_certificate.S: use real contents instead of macro GLOBAL()
KEYS: fix error return code in big_key_instantiate()
KEYS: Fix keyring quota misaccounting on key replacement and unlink
KEYS: Fix a race between negating a key and reading the error set
KEYS: Make BIG_KEYS boolean
apparmor: remove the "task" arg from may_change_ptraced_domain()
apparmor: remove parent task info from audit logging
apparmor: remove tsk field from the apparmor_audit_struct
apparmor: fix capability to not use the current task, during reporting
Smack: Ptrace access check mode
ima: provide hash algo info in the xattr
ima: enable support for larger default filedata hash algorithms
ima: define kernel parameter 'ima_template=' to change configured default
ima: add Kconfig default measurement list template
...
