Other MMC hosts handle a regulator named vmmc-supply that allows to power
the MMC card or SDIO device before communicating on the bus.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Chris Ball <chris@printf.net>
Add a driver for Arasan's SDHCI controller core.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Rob Herring <rob.herring@calxeda.com> [binding]
Acked-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Chris Ball <chris@printf.net>
Suggested by Jaehoon: Use slot-gpio to handle cd-gpio
Add function dw_mci_of_get_cd_gpio to check "cd-gpios" from dts.
mmc_gpio_request_cd and mmc_gpio_get_cd are used to handle cd pin
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <chris@printf.net>
Add O2Micro/BayHubTech SD Host DeviceId 8520 support.
Add O2Micro/BayHubTech SD Host DeviceId 8420 & 8421 support.
Add O2Micro/BayHubTech SD Host DeviceId 8620 & 8621 support.
These card readers are used in laptops like Lenovo ThinkPad W540,
Dell Latitude E5440, Dell Latitude E6540.
Signed-off-by: Peter Guo <peter.guo@bayhubtech.com>
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: Chris Ball <chris@printf.net>
Break out definitions in sdhci-pci.c to sdhci-pci.h, for introducing
module files like sdhci-pci-xxx.c
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: Chris Ball <chris@printf.net>
This patch fixes the below compile error:
${LINUX}/drivers/mmc/host/tmio_mmc.c: In function 'tmio_mmc_probe':
${LINUX}/drivers/mmc/host/tmio_mmc.c:93:35: \
error: 'res_ctl' undeclared (first use in this function)
${LINUX}/drivers/mmc/host/tmio_mmc.c:93:35: \
note: each undeclared identifier is reported only \
once for each function it appears in
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Chris Ball <chris@printf.net>
This helps increasing build testing coverage.
The driver doesn't compile on (at least) x86 due (possibly among others)
to missing readsw/writesw I/O accessors, restrict compilation to SUPERH
or ARM.
Whether the CTL_DMA_ENABLE register is part of the standard TMIO
controller or is Renesas-specific is unknown and impossible to test as
we have no current or planned TMIO DMA users other than SUPERH and
ARCH_SHMOBILE. Writing to the register is thus conditionally compiled
for SUPERH and ARCH_SHMOBILE only. Adding ARCH_SHMOBILE_MULTI to the
list would extend this to multiarch kernels, but would break the driver
for non-shmobile platforms if the register is Renesas-specific. We can
thus get rid of the conditional compilation completely without
introducing any further issue, and let future non-Renesas users deal
with the situation if it turns out to be a the problem.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
Tegra124's MMC controller is very similar to earlier SoC generations,
and can be supported by the same driver.
However, there are some non-backwards-compatible HW differences, and
hence a new DT compatible value must be used to describe the HW. This
patch updates the driver to support that new compatible value.
That said, the HW differences are only relevant when enabling certain
high-performance transfer modes. Since the driver is currently very
simple and doesn't enable those modes, we don't actually need to address
any of these HW differences in the code yet, hence the simple nature of
this patch.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Casting an integer to a void * generates a "cast to pointer from integer
of different size" warning. Cast the integer to an unsigned long first
to fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The channel request and configuration code is duplicated for the rx and
tx channels. Create a function that requests a single channel and call
it twice instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
One of Renesas SDHI chip needs workaround to use it, and, we can judge
it based on chip version. This patch adds very quick-hack workaround
method, since we still don't know how many chips need workaround in
the future.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The accessibility checking method to the higher register was added by
69d1fe18e9 (mmc: tmio: only access registers above 0xff, if available)
But, it doesn't care 32bit register. It is impossible to calculate it
from the resource size, since there is 16/32 bit register IP (e.g. VERSION
is located on 0xe2 if 16bit register, but it is located on 0x1c4 if 32bit
register).
This patch adds new TMIO_MMC_HAVE_HIGH_REG flags, tmio_mmc driver has it,
and sh_mobile_sdhi doesn't have it today.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
.bus_shift is used to 16/32bit register access offset calculation on
tmio driver. tmio_mmc_xxx is used from Toshiba/Renesas now, but this
bus_shift value depends on HW IP. This patch moves .bus_shift to
tmio_mmc_data member and sets it on each driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Current tmio driver tries to use default ocr_avail if 1) it couldn't
find regulator and 2) if platform data doesn't have ocr_mask.
But, there is no guarantee that regulator driver probe is faster than
TMIO driver probe. TMIO driver will not use regulator in such case.
By this patch, TMIO driver returns -EPROBE_DEFER if it couldn't find
regulator and if platform doesn't have ocr_mask. Because, there is a
possibility that regulator has not been probed, but the user expects it.
This patch changes tmio_mmc_host_probe() behavior, but there is no user
who has conflict.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use generic helper function. This also adds support for the cd-gpios and
max-frequency devicetree properties.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This also fixes that the read-only gpio was used without being
requested.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
We have a MMC_CAP2_CD_ACTIVE_HIGH flag, so use it rather than a custom
driver specific flag.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use the standard MMC_CAP_NEEDS_POLL flag rather than a custom broken_cd
flag. The original code used to just return true in the card detection
function for broken card detection. The MMC_CAP_NEEDS_POLL works different,
but was introduced for the same purpose, so assume the code works correct
now.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The standard caps already have a MMC_CAP_NONREMOVABLE flag. Use it
rather than a custom non_removable flag.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Non removable cards are always present, so do not call get_cd for them.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Newer Intel PCHs with LPSS have the same SDHCI controller than Haswell but
ACPI ID is different. Add this ID to the driver list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Turn clk_enable() and clk_disable() calls into clk_prepare_enable() and
clk_disable_unprepare() to get ready for the migration to the common
clock framework.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix the following sparse warning:
drivers/mmc/host/sdhci-esdhc-imx.c:617:35: warning: Using plain integer as NULL pointer
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
In function sdhci_request(), it is possible to do the tuning execution
like below:
sdhci_request() {
spin_lock_irqsave(&host->lock, flags);
host->mrq = mrq;
...
spin_unlock_irqrestore(&host->lock, flags);
<=== Here it is possible one pending finish_tasklet get running
and it will operate the original mrq, and notified the mrq
is done, and causes memory corruption.
sdhci_execute_tuning(mmc, tuning_opcode);
spin_lock_irqsave(&host->lock, flags);
host->mrq = mrq;
...
}
In the above race place, the original mrq should not be finished wrongly,
so here before unlock the spinlock, we need to set the host->mrq to NULL
to avoid this case.
Signed-off-by: Liu, Chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since I'm currently unable to dedicate sufficient time to driver
maintainership, remove myself from the maintainers list.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
With some SDIO devices, timeout errors can happen when reading data.
To solve this issue, the DMA transfer has to be activated before sending
the command to the device. This order is incorrect in PDC mode. So we
have to take care if we are using DMA or PDC to know when to send the
MMC command.
Cc: stable <stable@vger.kernel.org> # 3.2+
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
02cb3221d5 ("mmc: tmio: support caps2 flags") added caps2 support on
tmio, but it overwrites mmc_of_parse() settings. This patch fixes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Laurent <laurent.pinchart@ideasonboard.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Under function mmc_blk_issue_rq, after an MMC discard operation,
the MMC request data structure may be freed in memory. Later in
the same function, the check of req->cmd_flags & MMC_REQ_SPECIAL_MASK
is dangerous and invalid. It causes the MMC host not to be released
when it should.
This patch fixes the issue by marking the special request down before
the discard/flush operation.
Reported by: Harold (SoonYeal) Yang <haroldsy@broadcom.com>
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The root clock will be disabled in runtime pm to save power.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since we're using common esdhc_send_command for tuning commands and
the core code will call pm_runtime_put after command is finished.
So we add a pm_runtime_get_sync here to get the balance.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Current code will clear all turning related bits like ESDHC_STD_TUNING_EN
and ESDHC_MIX_CTRL_FBCLK_SEL when clear SDHCI_CTRL_EXEC_TUNING.
This may cause the card which has already passed the turning to become
unwork since the turning status lost.
We observed this failure when enable runtime pm.
BTW, imx needs to enable ESDHC_MIX_CTRL_FBCLK_SEL bit for turned clock.
The FBCLK_SEL will be cleared when SDHCI_CTRL_TUNED_CLK is cleared
and SDHCI_CTRL_EXEC_TUNING is not set.
This is used in case we change to another normal card from a UHS card
in the same slot. FBCLK_SEL is not needed for normal card.
After that, SDHCI_CTRL_EXEC_TUNING will only affect ESDHC_MIX_CTRL_EXE_TUNE.
Clearing it does not affect the turned card to remain working on UHS mode.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
We should not clear tuning bits during reset or the SD3.0/eMMC4.5 card
working on UHS mode may not work after reset since the former tuning
settings was lost.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
It is helpful for platform code to use to eliminate duplicated code.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add support for eMMC 4.5 cards to work on hs200 mode.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The MMC_CAP_UHS_DDR50 must work on 1.8v.
However, the eMMC DDR mode can work on either 1.8v or 3.3v and
should not depend on UHS_DDR50.
So get rid of this limitation to let controller without 1.8v
signal voltage support can also work for eMMC DDR mode if it claims.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
We should use '|=' instead '=', or it may over write the original
caps assigned before this line.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Used to read out the correct value of SDHCI_TRANSFER_MODE register
for upper layer.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The auto cmd settings bits should be cleared before sending new commands
or we may receive command timeout error for normal commands due to wrongly
pre-sent auto cmd.
e.g. we receive CMD13 timeout error due to ACMD23 is wrongly enabled
by former data commands.
mmc2: new high speed DDR MMC card at address 0001
mmcblk1: mmc2:0001 SEM08G 7.39 GiB
mmcblk1boot0: mmc2:0001 SEM08G partition 1 2.00 MiB
mmcblk1boot1: mmc2:0001 SEM08G partition 2 2.00 MiB
mmcblk1rpmb: mmc2:0001 SEM08G partition 3 128 KiB
mmcblk1: p1 p2 p3 p4 < p5 p6 p7 >
mmc2: Timeout waiting for hardware interrupt.
mmcblk1boot1: unknown partition table
mmc2: Timeout waiting for hardware interrupt.
mmcblk1boot0: unknown partition table
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Mostly bugfixes and a few small code removals. Worth pointing out is:
- A handful of more fixes to get DT enablement working properly on OMAP,
finding new breakage of things that don't work quite right yet without
the traditional board files. I expect a bit more of this to come in this
release as people test on their hardware.
- Implementation of power_down_finish() on vexpress, to make kexec work and
to stop the MCPM core to produce a warning (the warning was new to 3.13-rc1).
- A handful of minor fixes for various platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJSlPDhAAoJEIwa5zzehBx31dkP/RyP/esMHSBO5k36eB5V35HP
/XcexbgnnH4tDVIKl28qH4/AjkT+09uNZ/QQpbshwmEHw1X5i+Dz455suBCdP0T7
D+dHy/YCMDuMD7ow0OXWyyL9XbILV5VuBUogrdMN/RhzW2gIvIJRuHztKBQcU8sw
L94OIPjlKX/YFrswuy0LXiIZt2Y2k3zFVFCwcxIpTB4F1avYj7luZjSX6y469TEB
JyqfO+hooU/qtuc1pKTnBzKxVI7IVae3bberDhZCCKsAxP1/c5rSMy+nf60rqB4O
nkT09sAr1SBVp6kB4Ql2yHGiZ5ozxSJbMQpx1v73wnS09wL9RXwR1GZPrNcDW90l
qwergTrBxhYdzWyNAf/87DmQhB+Xf7kGqtUuRHleuuFhBOU29qR8oXQ6WMRkzHn9
ZTSRZ99l5a3Aul8w+sEWzOKDdZfhycMsBNzWH8xpzR1fgH4N9GRJlSlqkWdrVGca
QBNiC5bmtPpMgAHSkqK0Zu3rog83NX9NxcXG15FVEah7J4Q/VT/x51AIh0uSRBf0
35lY86R79SQ3FYYyHhl2pyAw8nhY2EmofGSG2WJ+qfZ9TgDSDFdwA0hz2fp9nwFc
Lwb3zGUEyGwgJ4I/n/cDGBfY2CsJuTEcDtB4sW1Vw4GrzMQvc43SWly6e5+RSAgq
reP23wcD4/YKev7//zzI
=zdhe
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Mostly bugfixes and a few small code removals. Worth pointing out is:
- A handful of more fixes to get DT enablement working properly on
OMAP, finding new breakage of things that don't work quite right
yet without the traditional board files. I expect a bit more of
this to come in this release as people test on their hardware.
- Implementation of power_down_finish() on vexpress, to make kexec
work and to stop the MCPM core to produce a warning (the warning
was new to 3.13-rc1).
- A handful of minor fixes for various platforms"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: bcm2835: add missing #xxx-cells to I2C nodes
ARM: dts: Add max77686 RTC interrupt to cros5250-common
ARM: vexpress/TC2: Implement MCPM power_down_finish()
ARM: tegra: Provide dummy powergate implementation
ARM: omap: fix warning with LPAE build
ARM: OMAP2+: Remove legacy omap4_twl6030_hsmmc_init
ARM: OMAP2+: Remove legacy mux code for display.c
ARM: OMAP2+: Fix undefined reference to set_cntfreq
gpio: twl4030: Fix passing of pdata in the device tree case
gpio: twl4030: Fix regression for twl gpio output
ARM: OMAP2+: More randconfig fixes for reconfigure_io_chain
ARM: dts: imx6qdl: disable spdif "rxtx5" clock option
ARM: dts: Fix omap2 specific dtsi files by adding the missing entries
ARM: OMAP2+: Fix GPMC and simplify bootloader timings for 8250 and smc91x
i2c: omap: Fix missing device tree flags for omap2
Pull IMA fixes from James Morris:
"These three patches fix regressions in the IMA code in your current
tree.
The first fixes a couple of bugs in template_desc_init_fields(), and
the other two ensure that changes in this kernel don't break
userspace"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
ima: make a copy of template_fmt in template_desc_init_fields()
ima: do not send field length to userspace for digest of ima template
ima: do not include field length in template digest calc for ima template
NTB-RP Link Up issue, Xeon Doorbell errata workaround, ntb_transport
link down race, and correct dmaengine_get/put usage. Also, clean-ups
to remove duplicate defines and document a hardware errata. Finally,
some changes to improve performance.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=nOG2
-----END PGP SIGNATURE-----
Merge tag 'ntb-3.13' of git://github.com/jonmason/ntb
Pull non-transparent bridge updates from Jon Mason:
"NTB driver bug fixes to address a missed call to pci_enable_msix,
NTB-RP Link Up issue, Xeon Doorbell errata workaround, ntb_transport
link down race, and correct dmaengine_get/put usage.
Also, clean-ups to remove duplicate defines and document a hardware
errata. Finally, some changes to improve performance"
* tag 'ntb-3.13' of git://github.com/jonmason/ntb:
NTB: Disable interrupts and poll under high load
NTB: Enable Snoop on Primary Side
NTB: Document HW errata
NTB: remove duplicate defines
NTB: correct dmaengine_get/put usage
NTB: Fix ntb_transport link down race
ntb: Fix missed call to pci_enable_msix()
NTB: Fix NTB-RP Link Up
NTB: Xeon Doorbell errata workaround
The I2C controller node needs #address-cells and #size-cells properties,
but these are currently missing. Add them. This allows child nodes to be
parsed correctly.
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Follow-up to commit 294d31e822 ("sony-laptop: don't change keyboard
backlight settings"): avoid messing up the state on resume. Leave it to
what was before suspending as it's anyway likely that we still don't
know what value we should write to the EC registers. This fix is also
required in 3.12
Cc: stable@vger.kernel.org
Tested-by: Karol Babioch <karol@babioch.de>
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
