As described in the added code comment, a reference to .exit.text is ok
for drivers registered via module_platform_driver_probe(). Make this
explicit to prevent a section mismatch warning.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231002080529.2535610-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
As described in the added code comment, a reference to .exit.text is ok
for drivers registered via module_platform_driver_probe(). Make this
explicit to prevent a section mismatch warning.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231002080529.2535610-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Some devices (e.g. BCM72112) use an alarm_irq interrupt that is
connected to a level interrupt controller rather than an edge
interrupt controller. In this case, the interrupt cannot be left
enabled by the irq handler while preserving the hardware wake-up
signal on wake capable devices or an interrupt storm will occur.
The alarm_expired flag is introduced to allow the disabling of
the interrupt when an alarm expires and to support balancing the
calls to disable_irq() and enable_irq() in accordance with the
existing design.
Fixes: 24304a8715 ("rtc: brcmstb-waketimer: allow use as non-wake alarm")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230830224747.1663044-1-opendmb@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Subsystem:
- Add a way for drivers to tell the core the supported alarm range is smaller
than the date range. This is not used yet but will be useful for the
alarmtimers in the next release.
- fix Wvoid-pointer-to-enum-cast warnings
- remove redundant of_match_ptr()
- stop warning for invalid alarms when the alarm is disabled
Drivers:
- isl12022: allow setting the trip level for battery level detection
- pcf2127: add support for PCF2131 and multiple timestamps
- stm32: time precision improvement, many fixes
- twl: NVRAM support
-----BEGIN PGP SIGNATURE-----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=4kkJ
-----END PGP SIGNATURE-----
Merge tag 'rtc-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Subsystem:
- Add a way for drivers to tell the core the supported alarm range is
smaller than the date range. This is not used yet but will be
useful for the alarmtimers in the next release.
- fix Wvoid-pointer-to-enum-cast warnings
- remove redundant of_match_ptr()
- stop warning for invalid alarms when the alarm is disabled
Drivers:
- isl12022: allow setting the trip level for battery level detection
- pcf2127: add support for PCF2131 and multiple timestamps
- stm32: time precision improvement, many fixes
- twl: NVRAM support"
* tag 'rtc-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (73 commits)
dt-bindings: rtc: ds3231: Remove text binding
rtc: wm8350: remove unnecessary messages
rtc: twl: remove unnecessary messages
rtc: sun6i: remove unnecessary message
rtc: stop warning for invalid alarms when the alarm is disabled
rtc: twl: add NVRAM support
rtc: pcf85363: Allow to wake up system without IRQ
rtc: m48t86: add DT support for m48t86
dt-bindings: rtc: Add ST M48T86
rtc: pcf2127: remove useless check
rtc: rzn1: Report maximum alarm limit to rtc core
rtc: ds1305: Report maximum alarm limit to rtc core
rtc: tps6586x: Report maximum alarm limit to rtc core
rtc: cmos: Report supported alarm limit to rtc infrastructure
rtc: cros-ec: Detect and report supported alarm window size
rtc: Add support for limited alarm timer offsets
rtc: isl1208: Fix incorrect logic in isl1208_set_xtoscb()
MAINTAINERS: remove obsolete pattern in RTC SUBSYSTEM section
rtc: tps65910: Remove redundant dev_warn() and do not check for 0 return after calling platform_get_irq()
rtc: omap: Do not check for 0 return after calling platform_get_irq()
...
The RTC core already prints a message when the RTC is registered and when
registering fails, it is not necessary to have more in the driver.
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230827221643.544259-3-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The core already print a message once the rtc is successfully registered,
it is not necessary to print an other one.
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230827221643.544259-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When the alarm is not enabled, it may never have been set and so we can't
expect it to be valid. This will prevent the apparition of boot messages
like this one:
rtc rtc0: invalid alarm value: 2023-7-8 45:85:85
Link: https://lore.kernel.org/r/20230827221532.543353-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When wakeup-source is set in the devicetree, set up the device for
using the output as interrupt instead of clock. This is similar to
how other RTC devices handle this.
This allows the clock chip to turn on the board when wired to do
so in hardware.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Link: https://lore.kernel.org/r/20230821072013.7072-1-mike.looijmans@topic.nl
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
RZN1 only supports alarms up to one week in the future.
Report the limit to the RTC core and use the reported limit
to validate the requested alarm time when setting it.
Cc: Brian Norris <briannorris@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230817225537.4053865-8-linux@roeck-us.net
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
DS1305 only supports alarms up to 24 hours in the future.
Report the limit to the RTC core, and use the reported limit
to validate the requested alarm time when setting it.
If the alarm is too large when trying to set an alarm, return -ERANGE
instead of -EDOM to align with error codes returned by other rtc drivers.
Cc: Brian Norris <briannorris@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230817225537.4053865-7-linux@roeck-us.net
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
tps6586x only supports alarms up to 16,383 seconds in the future.
Report the limit to the RTC core.
Cc: Brian Norris <briannorris@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230817225537.4053865-6-linux@roeck-us.net
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The alarm window supported by the cmos RTC depends on the chip
and its configuration. Report the limit to the RTC core.
Cc: Brian Norris <briannorris@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230817225537.4053865-5-linux@roeck-us.net
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC on some older Chromebooks can only handle alarms less than
24 hours in the future. The only way to find out is to try to set
an alarm further in the future. If that fails, assume that the RTC
connected to the EC can only handle less than 24 hours of alarm
window, and report that value to the RTC core.
After that change, it is no longer necessary to limit the alarm time
when setting it. Report any excessive alarms to the caller instead.
Cc: Brian Norris <briannorris@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230817225537.4053865-4-linux@roeck-us.net
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The XTOSCB bit is not bit 0, but xtosb_val is either 0 or 1. If it is 1,
test will never succeed. Fix this issue by using double negation.
While at it, remove unnecessary blank line from probe().
Reported-by: Pavel Machek <pavel@denx.de>
Closes: https://lore.kernel.org/all/ZN4BgzG2xmzOzdFZ@duo.ucw.cz/
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Link: https://lore.kernel.org/r/20230817161038.407960-1-biju.das.jz@bp.renesas.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
It is not possible for platform_get_irq() to return 0. Use the
return value from platform_get_irq().
And there is no need to call the dev_warn() function directly to print
a custom message when handling an error from platform_get_irq()
function as it is going to display an appropriate error message
in case of a failure.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20230803080713.4061782-3-ruanjinjie@huawei.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
It is not possible for platform_get_irq() to return 0. Use the
return value from platform_get_irq().
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20230803080713.4061782-2-ruanjinjie@huawei.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This keeps the IRQ enabled during system suspend, if the RTC's wakeup
source is enabled. Since the IRQ is not required to wake from shutdown,
continue to add the wakeup source even if registering the wakeirq fails.
See commit 029d3a6f2f ("rtc: da9063: add as wakeup source").
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Link: https://lore.kernel.org/r/20230717190937.1301509-1-samuel.holland@sifive.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
If PCF2127 device is absent from the I2C bus, or if there is a
communication problem, disabling POR0 may fail silently and we
still continue with probing the device. In that case, abort probe
operation.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230728171211.3016019-1-hugo@hugovil.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This converts the DS2404 to use GPIO descriptors instead of
hard-coded global GPIO numbers.
The platform data can be deleted because there are no in-tree
users and it only contained GPIO numbers which are now
passed using descriptor tables (or device tree or ACPI).
The driver was rewritten to use a state container for the
device driver state (struct ds2404 *chip) and pass that
around instead of using a global singleton storage for the
GPIO handles.
When declaring GPIO descriptor tables or other hardware
descriptions for the RTC driver, implementers should take care
to flag the RESET line as active low, such as by using the
GPIOD_ACTIVE_LOW flag in the descriptor table.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230807-descriptors-rtc-v1-1-ce0f9187576e@linaro.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
After the switch to SET_NOIRQ_SYSTEM_SLEEP_PM_OPS() and a subsequent
fix, stm32_rtc_{suspend,resume}() are unused when CONFIG_PM_SLEEP is not
set because SET_NOIRQ_SYSTEM_SLEEP_PM_OPS() is a no-op in that
configuration:
drivers/rtc/rtc-stm32.c:904:12: error: 'stm32_rtc_resume' defined but not used [-Werror=unused-function]
904 | static int stm32_rtc_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~
drivers/rtc/rtc-stm32.c:894:12: error: 'stm32_rtc_suspend' defined but not used [-Werror=unused-function]
894 | static int stm32_rtc_suspend(struct device *dev)
| ^~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
The non-"SET_" version of this macro, NOIRQ_SYSTEM_SLEEP_PM_OPS(), is
designed to handle this situation by only assigning the callbacks when
CONFIG_PM_SLEEP is set while allowing the functions to appear used to
the compiler. Switch to that macro to resolve the warnings. There is no
functional change with this, as SET_NOIRQ_SYSTEM_SLEEP_PM_OPS() is
defined using NOIRQ_SYSTEM_SLEEP_PM_OPS() when CONFIG_PM_SLEEP is set.
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230815-rtc-stm32-unused-pm-funcs-v1-1-82eb8e02d903@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
'type' is an enum, thus cast of pointer on 64-bit compile test with W=1
causes:
rtc-rs5c372.c:829:19: error: cast to smaller integer type 'enum rtc_type' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810103902.151145-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
'type' is an enum, thus cast of pointer on 64-bit compile test with W=1
causes:
rtc-jz4740.c:352:14: error: cast to smaller integer type 'enum jz4740_rtc_type' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810103902.151145-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
'type' is an enum, thus cast of pointer on 64-bit compile test with W=1
causes:
rtc-rv8803.c:648:18: error: cast to smaller integer type 'enum rv8803_type' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810103902.151145-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
'type' is an enum, thus cast of pointer on 64-bit compile test with W=1
causes:
rtc-ds1307.c:1747:18: error: cast to smaller integer type 'enum ds_type' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810103902.151145-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
If device tree implies that the chip's IRQ/F_OUT pin is used as a
clock, expose that in the driver. For now, pretend it is a
fixed-rate (32kHz) clock; if other use cases appear the driver can be
updated to provide its own clk_ops etc.
When the clock output is not used on a given board, one can prolong
the battery life by ensuring that the FOx bits are 0. For the hardware
I'm currently working on, the RTC draws 1.2uA with the FOx bits at
their default 0001 value, dropping to 0.88uA when those bits are
cleared.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20230615105826.411953-9-linux@rasmusvillemoes.dk
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Since the meaning of the SR_LBAT85 and SR_LBAT75 bits are different in
battery backup mode, they may very well be set after power on, and
stay set for up to a minute (i.e. until the battery detection in VDD
mode happens when the seconds counter hits 59). This would mean that
userspace doing a ioctl(RTC_VL_READ) early on could get a false
positive.
The battery level detection can also be triggered by explicitly
writing a 1 to the TSE bit in the BETA register. Do that once during
boot. Empirically, this does not immediately update the bits in
the status register (i.e., an immediate read of SR after this write
can still show stale values), but the update is done after a few
milliseconds, so certainly before the RTC device gets registered and
userspace has a chance of doing the ioctl() on this device.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20230615105826.411953-7-linux@rasmusvillemoes.dk
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Hook up support for reading the values of the SR_LBAT85 and SR_LBAT75
bits. Translate the former to "battery low", and the latter to
"battery empty or not-present".
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20230615105826.411953-6-linux@rasmusvillemoes.dk
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Implement support for using the values given in the
isil,battery-trip-levels-microvolt property to set appropriate values
in the VB85TP/VB75TP bits in the PWR_VBAT register.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20230615105826.411953-5-linux@rasmusvillemoes.dk
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
There are multiple problems with this warning.
First of all, it triggers way too often, in fact nearly on every boot,
because the SR_LBAT85/SR_LBAT75 bits have another meaning when in
battery backup mode. Quoting from the data sheet:
LOW BATTERY INDICATOR 85% BIT (LBAT85)
In Normal Mode (VDD), this bit indicates when the battery level has
dropped below the pre-selected trip levels. [...] The LBAT85
detection happens automatically once every minute when seconds
register reaches 59.
In Battery Mode (VBAT), this bit indicates the device has entered
into battery mode by polling once every 10 minutes. The LBAT85
detection happens automatically once when the minute register
reaches x9h or x0h minutes.
Similar wording applies to the LBAT75 bit.
This means that if the device is powered off for more than 10 minutes,
the LBAT85 bit is guaranteed to be set. Upon power-on, unless we're
close enough to the end of a minute and/or the boot is slow enough
that the second register passes 59, the LBAT85 bit is still set when
the kernel (or early userspace) reads the RTC to set the system's
wallclock time.
Another minor problem is with the bit logic. If the 75% level is
reached, logically we're also below 85%, so both bits would most
likely be set. So even if the battery is below 75%, the warning would
still say "voltage dropped below 85%".
A third problem is that the driver and current DT binding offer no way
to indicate the nominal battery level and/or settings of the Battery
Level Monitor Trip Bits. Since the default value of the VB85TP[2:0] and
VB75TP[2:0] bits are 000, this means the actual setting of the
LBAT85/LBAT75 bits in VDD mode doesn't happen until the battery is below
2.125V/1.875V, which for a standard 3V battery is way too late.
A fourth problem is emitting this warning from ->read_time:
util-linux' hwclock will, in the absence of support for getting an
interrupt when the seconds counter is updated, issue
ioctl(RTC_RD_TIME) in a busy-loop until it sees a change in the
seconds field. In that case, if the battery low bits are set (either
genuinely, more than a minute after boot, due to the battery actually
being low, or as above, bogusly shortly after boot), the kernel log is
swamped with hundreds of identical warnings.
Subsequent patches will add such bindings and driver support, and also
proper support for RTC_VL_READ. For now, remove the broken warning.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20230615105826.411953-2-linux@rasmusvillemoes.dk
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Referring to platform_get_irq()'s definition, the return value has
already been checked if ret < 0, and printed via dev_err_probe().
Calling dev_err_probe() one more time outside platform_get_irq()
is obviously redundant.
Removing dev_err_probe() outside platform_get_irq() to clean up
above problem.
Signed-off-by: Chen Jiahao <chenjiahao16@huawei.com>
Link: https://lore.kernel.org/r/20230802093650.976352-1-chenjiahao16@huawei.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
After a previous commit changed the driver over to
SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(), the suspend/resume
functions must no longer be hidden behind an #ifdef:
In file included from include/linux/clk.h:13,
from drivers/rtc/rtc-stm32.c:8:
drivers/rtc/rtc-stm32.c:927:39: error: 'stm32_rtc_suspend' undeclared here (not in a function); did you mean 'stm32_rtc_probe'?
927 | SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(stm32_rtc_suspend, stm32_rtc_resume)
| ^~~~~~~~~~~~~~~~~
include/linux/kernel.h:58:44: note: in definition of macro 'PTR_IF'
58 | #define PTR_IF(cond, ptr) ((cond) ? (ptr) : NULL)
| ^~~
include/linux/pm.h:329:26: note: in expansion of macro 'pm_sleep_ptr'
329 | .suspend_noirq = pm_sleep_ptr(suspend_fn), \
| ^~~~~~~~~~~~
Fixes: fb9a7e5360 ("rtc: stm32: change PM callbacks to "_noirq()"")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230801105932.3738430-1-arnd@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
ds1685_rtc_poweroff is only used externally via symbol_get, which was
only ever intended for very internal symbols like this one. Use
EXPORT_SYMBOL_GPL for it so that symbol_get can enforce only being used
on EXPORT_SYMBOL_GPL symbols.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Joshua Kinard <kumba@gentoo.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
The driver was introduced when .probe_new was the right probe callback
to use for i2c drivers. Today .probe is the right one (again) and the
driver was already switched in commit 31b0cecb40 ("rtc: Switch i2c
drivers back to use .probe()") but the name continued to include "_new"
in its name.
To prevent code readers wondering about what might be new here, drop
that irritating part of the name.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230725070429.383070-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230724205456.767430-1-robh@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Property "trickle-resistor-ohms" allows us to set trickle charger
resistor. However there is no possibility to disable it afterwards.
Add support for "aux-voltage-chargeable" property which can be used to
enable/disable the trickle charger circuit explicitly. The default
behavior of the code is kept as it is!
Additionally, lets make sure we only update internal EEPROM in case of a
change. This prevents wear due to excessive EEPROM writes on each probe.
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Link: https://lore.kernel.org/r/20230623081533.76334-1-andrej.picej@norik.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The added HAS_IOPORT dependency might not actually be necessary as Geert
points out, but the driver is also only used on one architecture. Sparc
is also a special case here since it converts port numbers into virtual
addresses rather than having them mapped into a particular part of the
__iomem address space, so the difference is actually not important here.
Add a dependency on sparc, but allow compile-testing otherwise, to
make this clearer without anyone having to spend much time modernizing
the driver beyond that.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: David S. Miller <davem@davemloft.net>
Link: https://lore.kernel.org/all/CAMuHMdWEx0F=fNei4Bz_JPkuvoaN-+zk08h0i8KnSi_VjO615g@mail.gmail.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230719192835.1025406-1-arnd@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Drop enum pcf85063_type and split the array pcf85063_cfg[] as individual
variables, and make lines shorter by referring to e.g. &pcf85063_cfg
instead of &pcf85063_cfg[PCF85063].
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230717124059.196244-3-biju.das.jz@bp.renesas.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The pcf85063_ids[].driver_data could store a pointer to the config,
like for DT-based matching, making I2C and DT-based matching
more similar.
After that, we can simplify the probe() by replacing of_device_get_
match_data() and i2c_match_id() by i2c_get_match_data() as we have
similar I2C and DT-based matching table.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230717124059.196244-2-biju.das.jz@bp.renesas.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Simplify the probe() by replacing of_device_get_match_data() and
i2c_match_id() by i2c_get_match_data() as we have similar I2C
and DT-based matching table.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230710114747.106496-1-biju.das.jz@bp.renesas.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fix a few style issues reported by checkpatch.pl:
- Unnecessary parentheses
- Lines should not end with a '('
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230705174357.353616-8-valentin.caron@foss.st.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
stm32_rtc_valid_alrm function has some issues :
- arithmetical operations are impossible on BCD values
- "cur_mon + 1" can overflow
- the use case with the next month, the same day/hour/minutes went wrong
To solve that, we prefer to use timestamp comparison.
e.g. : On 5 Dec. 2021, the alarm limit is 5 Jan. 2022 (+31 days)
On 31 Jan 2021, the alarm limit is 28 Feb. 2022 (+28 days)
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230705174357.353616-7-valentin.caron@foss.st.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC driver stops the RTCAPB clock during suspend, but the
irq handler from RTC is called before starting clock. Then we are
blocked while accessing RTC registers.
We changes PM callbacks to '_no_irq()' to disable irq during
resume callback and so irq handler will be called after the enable
of RTCAPB clock.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230705174357.353616-6-valentin.caron@foss.st.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Change stm32-rtc driver to not generate an error message when
device probe operation is deferred for a clock.
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230705174357.353616-5-valentin.caron@foss.st.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The rtc is used to update the stgen counter on wake up from
low power modes, so it needs to be as much accurate as possible.
The maximization of asynchronous divider leads to a 4ms rtc
precision clock.
By decreasing pred_a to 0, it will have pred_s=32767 (when
need_accuracy is true), so stgen clock becomes more accurate
with 30us precision.
Nevertheless this will leads to an increase of power consumption.
Signed-off-by: Christophe Guibout <christophe.guibout@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230705174357.353616-4-valentin.caron@foss.st.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
RTC counters are stopped when INIT bit in ISR register is set and
start counting from the (eventual) new value when INIT is reset.
In stm32_rtc_init(), called during probe, the INIT bit is set to
program the prescaler and the 24h mode. This halts the RTC counter
at each probe tentative causing the RTC time to loose from 0.3s to
0.8s at each kernel boot.
If the RTC is battery powered, both prescaler value and 24h mode
are kept during power cycle and there is no need to program them
again.
Check if the desired prescaler value and the 24h mode are already
programmed, then skip reprogramming them to avoid halting the time
counter.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230705174357.353616-3-valentin.caron@foss.st.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Date and time are read from two separate RTC registers.
To ensure consistency between the two registers, reading the time
register locks the values in the shadow date register until the
date register is read.
Thus, the whole date/time read requires reading the time register
first, followed by reading the date register.
If the reads are done in reversed order, the shadow date register
will remain locked until a future read operation. The future read
will read the former date value that could be already invalid.
Fix the read order of date/time registers in stm32_rtc_valid_alrm()
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230705174357.353616-2-valentin.caron@foss.st.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The PCF2127/29 do NOT support alarms with a 1 second resolution, but
the PCF2131 does.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-17-hugo@hugovil.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The watchdog value register cannot be read on the PCF2131 after being
set.
Add a new flag to identify which variant has read access to this
register, and use this flag to selectively test if watchdog timer was
started by bootloader.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-16-hugo@hugovil.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Introduce in the configuration structure two new values to hold the
watchdog clock source and the min_hw_heartbeat_ms value.
The minimum and maximum timeout values are automatically computed from
the watchdog clock source value for each variant.
The PCF2131 has no 1Hz watchdog clock source, as is the case for
PCF2127/29.
The next best choice is using a 1/4Hz clock, giving a watchdog timeout
range between 4 and 1016s. By using the same register configuration as
for the PCF2127/29, the 1/4Hz clock source is selected.
Note: the PCF2127 datasheet gives a min/max range between 1 and 255s,
but it should be between 2 and 254s, because the watchdog is triggered
when the timer value reaches 1, not 0.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-15-hugo@hugovil.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The sequence for updating the time/date registers is slightly
different between PCF2127/29 and PCF2131.
For PCF2127/29, during write operations, the time counting
circuits (memory locations 03h through 09h) are automatically blocked.
For PCF2131, time/date registers write access requires setting the
STOP bit and sending the clear prescaler instruction (CPR). STOP then
needs to be released once write operation is completed.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-14-hugo@hugovil.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The PCF2127 and PCF2129 have one output interrupt pin. The PCF2131 has
two, named INT_A and INT_B. The hardware support that any interrupt
source can be routed to either one or both of them.
Force all interrupt sources to go to the INT A pin.
Support to route any interrupt source to INT A/B pins is not supported
by this driver at the moment.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-13-hugo@hugovil.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This RTC is very similar in functionality to the PCF2127/29.
Basically it:
-supports two new control registers at offsets 4 and 5
-supports a new reset register (not implemented in this driver)
-supports 4 tamper detection functions instead of 1
-has no nvmem (like the PCF2129)
-has two output interrupt pins
Because of that, most of the register addresses are very different,
although they still follow the same layout. For example, the tamper
registers have a different base address, but the offsets are all the same.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-12-hugo@hugovil.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This will simplify the implementation of new variants into this driver.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-10-hugo@hugovil.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This will simplify the implementation of new variants into this driver.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Tested-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-9-hugo@hugovil.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This will simplify the implementation of new variants into this driver.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-8-hugo@hugovil.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This will simplify the implementation of new variants into this driver.
Some variants (PCF2131) have a 100th seconds register. This register is
currently not supported in this driver.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-7-hugo@hugovil.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Create variant-specific configuration structures to simplify the
implementation of new variants into this driver. It will also avoid
to have too many tests for a specific variant, or a list of variants
for new devices, inside the code itself.
Add configuration options for the support of the NVMEM, bit CD0 in
register WD_CTL as well as the maximum number of registers for each
variant, instead of hardcoding the variant (PCF2127) inside the
i2c_device_id and spi_device_id structures.
Also specify a different maximum number of registers (max_register)
for the PCF2129.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-6-hugo@hugovil.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reading the 7 timetamp registers currently involves reading 25 registers
solely to be able to print the content of the three control registers,
in addition to the 7 timestamp registers. This print never occurs,
unless the user enables dynamic debug in this driver or set
CONFIG_RTC_DEBUG.
Reading the timestamp registers should consist of reading 7
consecutive timestamp registers.
This patch optimize the performance of reading the timestamp registers
by reading 7 consecutive registers instead of 25, and dropping the
print of the control registers.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-3-hugo@hugovil.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Improve performance and readability of rtc_read_time() by reading only
the 7 time registers, instead of reading 8 registers (additional CTRL3
register).
We drop reading of CTRL3 to monitor the low battery flag, as this
check is already available in the ioctl. Anyway, this check only
display an info message and has no other impacts.
The code readability also improves as we do not have to fiddle with
buffer pointer and size arithmetic.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-2-hugo@hugovil.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Subsystem:
- Switch i2c drivers back to use .probe()
- Constify pointers to hwmon_channel_info
New driver:
- Loongson on chip RTC, replacing the Loongson 1 only driver
Drivers:
- isl1208: cleanup and support for RAA215300
- st-lpc: cleanups
- stm32: fix wakeup
-----BEGIN PGP SIGNATURE-----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=+0zF
-----END PGP SIGNATURE-----
Merge tag 'rtc-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"The isl1208 dirver was reworked tobe able to work as part of an MFD.
All the Loongson chips are now supported through a new driver, the old
one is removed.
Summary:
Subsystem:
- Switch i2c drivers back to use .probe()
- Constify pointers to hwmon_channel_info
New driver:
- Loongson on chip RTC, replacing the Loongson 1 only driver
Drivers:
- isl1208: cleanup and support for RAA215300
- st-lpc: cleanups
- stm32: fix wakeup"
* tag 'rtc-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (21 commits)
rtc: Add rtc driver for the Loongson family chips
rtc: Remove the Loongson-1 RTC driver
dt-bindings: rtc: Split loongson,ls2x-rtc into SoC-based compatibles
rtc: rv3028: make rv3028 probeable from userspace
rtc: isl1208: Add support for the built-in RTC on the PMIC RAA215300
rtc: isl1208: Add isl1208_set_xtoscb()
rtc: isl1208: Drop enum isl1208_id and split isl1208_configs[]
rtc: isl1208: Make similar I2C and DT-based matching table
rtc: isl1208: Drop name variable
dt-bindings: rtc: isil,isl1208: Document clock and clock-names properties
dt-bindings: rtc: isl1208: Convert to json-schema
rtc: st-lpc: Simplify clk handling in st_rtc_probe()
rtc: st-lpc: Release some resources in st_rtc_probe() in case of error
rtc: stm32: remove dedicated wakeup management
dt-bindings: rtc: restrict node name suffixes
rtc: add HAS_IOPORT dependencies
rtc: Switch i2c drivers back to use .probe()
rtc: rv3032: constify pointers to hwmon_channel_info
rtc: isl12022: constify pointers to hwmon_channel_info
rtc: ds3232: constify pointers to hwmon_channel_info
...
SoC support. Instead there's a treewide patch series from Maxime that makes
clk_ops::determine_rate mandatory for muxes. Beyond that core framework change
we have the usual pile of clk driver updates such as migrating i2c drivers to
use .probe() again or YAMLfication of clk DT bindings so we can validate DTBs.
Overall the SoCs that got the most updates this time around in terms of
diffstat are the Amlogic and Mediatek drivers because they added new SoC
support or fixed up various drivers to have proper data.
In general things look kinda quiet. I suspect the core framework change may
still shake out some problems after the merge window, mostly because not
everyone tests linux-next where that series has been for some number of weeks.
I saw that there's at least one pending fix for Tegra that needs to be wrapped
up into a proper patch. I'll try to catch those bits before the window closes
so that -rc1 is bootable. More details below.
Core:
- Make clk_ops::determine_rate mandatory for muxes
New Drivers:
- Add amlogic a1 SoC family PLL and peripheral clock controller support
Updates:
- Handle allocation failures from kasprintf() and friends
- Migrate platform clk drivers to .remove_new()
- Migrate i2c clk drivers to .probe() instead of .probe_new()
- Remove CLK_SET_PARENT from all Mediatek MSDC core clocks
- Add infra_ao reset support for Mediatek MT8188 SoCs
- Align driver_data to i2c_device_id tables in some i2c clk drivers
- Use device_get_match_data() in vc5 clk driver
- New Kconfig symbol name (SOC_MICROCHIP_POLARFIRE) for Microchip FPGA clock
drivers
- Use of_property_read_bool() to read "microchip,pic32mzda-sosc" boolean DT
property in clk-pic32mzda
- Convert AT91 clock dt-bindings to YAML
- Remove CLK_SET_RATE_PARENT flag from LDB clocks on i.MX6SX
- Keep i.MX UART clocks enabled during kernel boot if earlycon is set
- Drop imx_unregister_clocks() as there are no users anymore
- Switch to _safe iterator on imx_clk_scu_unregister() to avoid use after free
- Add determine_rate op to the imx8m composite clock
- Use device managed API for iomap and kzalloc for i.MXRT1050, i.MX8MN,
i.MX8MP and i.MX93 clock controller drivers
- Add missing interrupt DT property for the i.MX8M clock controller
- Re-add support for Exynos4212 clock controller because we are
re-introducing the SoC in the mainline
- Add CONFIG_OF dependency to Samsung clk Kconfig symbols to solve some
objtool warnings
- Preselect PLL MIPI as TCON0 parent for Allwinner A64 SoC
- Convert the Renesas clock drivers to readl_poll_timeout_atomic()
- Add PWM clock on Renesas R-Car V3U
- Fix PLL5 on Renesas RZ/G2L and RZ/V2L
-----BEGIN PGP SIGNATURE-----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=6M8D
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This batch of clk driver updates contains almost no new SoC support.
Instead there's a treewide patch series from Maxime that makes
clk_ops::determine_rate mandatory for muxes.
Beyond that core framework change we have the usual pile of clk driver
updates such as migrating i2c drivers to use .probe() again or
YAMLfication of clk DT bindings so we can validate DTBs.
Overall the SoCs that got the most updates this time around in terms
of diffstat are the Amlogic and Mediatek drivers because they added
new SoC support or fixed up various drivers to have proper data.
In general things look kinda quiet. I suspect the core framework
change may still shake out some problems after the merge window,
mostly because not everyone tests linux-next where that series has
been for some number of weeks. I saw that there's at least one pending
fix for Tegra that needs to be wrapped up into a proper patch. I'll
try to catch those bits before the window closes so that -rc1 is
bootable. More details below.
Core:
- Make clk_ops::determine_rate mandatory for muxes
New Drivers:
- Add amlogic a1 SoC family PLL and peripheral clock controller support
Updates:
- Handle allocation failures from kasprintf() and friends
- Migrate platform clk drivers to .remove_new()
- Migrate i2c clk drivers to .probe() instead of .probe_new()
- Remove CLK_SET_PARENT from all Mediatek MSDC core clocks
- Add infra_ao reset support for Mediatek MT8188 SoCs
- Align driver_data to i2c_device_id tables in some i2c clk drivers
- Use device_get_match_data() in vc5 clk driver
- New Kconfig symbol name (SOC_MICROCHIP_POLARFIRE) for Microchip
FPGA clock drivers
- Use of_property_read_bool() to read "microchip,pic32mzda-sosc"
boolean DT property in clk-pic32mzda
- Convert AT91 clock dt-bindings to YAML
- Remove CLK_SET_RATE_PARENT flag from LDB clocks on i.MX6SX
- Keep i.MX UART clocks enabled during kernel boot if earlycon is set
- Drop imx_unregister_clocks() as there are no users anymore
- Switch to _safe iterator on imx_clk_scu_unregister() to avoid use
after free
- Add determine_rate op to the imx8m composite clock
- Use device managed API for iomap and kzalloc for i.MXRT1050,
i.MX8MN, i.MX8MP and i.MX93 clock controller drivers
- Add missing interrupt DT property for the i.MX8M clock controller
- Re-add support for Exynos4212 clock controller because we are
re-introducing the SoC in the mainline
- Add CONFIG_OF dependency to Samsung clk Kconfig symbols to solve
some objtool warnings
- Preselect PLL MIPI as TCON0 parent for Allwinner A64 SoC
- Convert the Renesas clock drivers to readl_poll_timeout_atomic()
- Add PWM clock on Renesas R-Car V3U
- Fix PLL5 on Renesas RZ/G2L and RZ/V2L"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (149 commits)
clk: fix typo in clk_hw_register_fixed_rate_parent_data() macro
clk: Fix memory leak in devm_clk_notifier_register()
clk: mvebu: Iterate over possible CPUs instead of DT CPU nodes
clk: mvebu: Use of_get_cpu_hwid() to read CPU ID
MAINTAINERS: Add Marvell mvebu clock drivers
clk: clocking-wizard: check return value of devm_kasprintf()
clk: ti: clkctrl: check return value of kasprintf()
clk: keystone: sci-clk: check return value of kasprintf()
clk: si5341: free unused memory on probe failure
clk: si5341: check return value of {devm_}kasprintf()
clk: si5341: return error if one synth clock registration fails
clk: cdce925: check return value of kasprintf()
clk: vc5: check memory returned by kasprintf()
clk: mediatek: clk-mt8173-apmixedsys: Fix iomap not released issue
clk: mediatek: clk-mt8173-apmixedsys: Fix return value for of_iomap() error
clk: mediatek: clk-mtk: Grab iomem pointer for divider clocks
clk: keystone: syscon-clk: Add support for audio refclk
dt-bindings: clock: Add binding documentation for TI Audio REFCLK
dt-bindings: clock: ehrpwm: Remove unneeded syscon compatible
clk: keystone: syscon-clk: Allow the clock node to not be of type syscon
...
The Loongson family chips use an on-chip counter 0 (Time Of Year
counter) as the RTC. We will refer to them as rtc-loongson.
Cc: Keguang Zhang <keguang.zhang@gmail.com>
Cc: Yang Ling <gnaygnil@gmail.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@kernel.org>
Signed-off-by: WANG Xuerui <git@xen0n.name>
Reviewed-by: Keguang Zhang <keguang.zhang@gmail.com>
Tested-by: Keguang Zhang <keguang.zhang@gmail.com>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com> # LS7A
Link: https://lore.kernel.org/r/0c5171156390f614d72f36ceb04a20f432ca639e.1685693501.git.zhoubinbin@loongson.cn
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Remove the ls1x-rtc driver as it is obsolete. We will continue to
support the ls1x RTC in the upcoming Loongson unified RTC driver
rtc-loongson.
Cc: Keguang Zhang <keguang.zhang@gmail.com>
Cc: zhao zhang <zhzhl555@gmail.com>
Cc: Yang Ling <gnaygnil@gmail.com>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Acked-by: Keguang Zhang <keguang.zhang@gmail.com>
Link: https://lore.kernel.org/r/c38c666015a162d7031b20a48209ce577bab62cd.1685693501.git.zhoubinbin@loongson.cn
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
With this commit, it will be possible to bind a rv3028 device from
userspace
This is done by:
echo rtc-rv3028 0x52 > /sys/bus/i2c/devices/i2c-XX/new_device
Signed-off-by: Johannes Kirchmair <johannes.kirchmair@sigmatek.at>
Link: https://lore.kernel.org/r/20230327085550.1721861-1-johannes.kirchmair@sigmatek.at
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The built-in RTC found on PMIC RAA215300 is the same as ISL1208.
However, the external oscillator bit is inverted on PMIC version
0x11. The PMIC driver detects PMIC version and instantiates the
RTC device based on i2c_device_id.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230623140948.384762-11-biju.das.jz@bp.renesas.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
As per the HW manual, set the XTOSCB bit as follows:
If using an external clock signal, set the XTOSCB bit as 1 to
disable the crystal oscillator.
If using an external crystal, the XTOSCB bit needs to be set at 0
to enable the crystal oscillator.
Add isl1208_set_xtoscb() to set XTOSCB bit based on the clock-names
property. Fallback is enabling the internal crystal oscillator.
While at it, introduce a variable "sr" for reading the status register
in probe() as it is reused for writing and also remove the unnecessary
blank line.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230623140948.384762-10-biju.das.jz@bp.renesas.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Drop enum isl1208_id and split the array isl1208_configs[] as individual
variables, and make lines shorter by referring to e.g. &config_isl1219
instead of &isl1208_configs[TYPE_ISL1219].
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230623140948.384762-9-biju.das.jz@bp.renesas.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The isl1208_id[].driver_data could store a pointer to the config,
like for DT-based matching, making I2C and DT-based matching
more similar.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230623140948.384762-8-biju.das.jz@bp.renesas.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The Allwinner sun6i RTC clock implements a mux with a set_parent hook,
but doesn't provide a determine_rate implementation.
This is a bit odd, since set_parent() is there to, as its name implies,
change the parent of a clock. However, the most likely candidates to
trigger that parent change are either the assigned-clock-parents device
tree property or a call to clk_set_rate(), with determine_rate()
figuring out which parent is the best suited for a given rate.
The other trigger would be a call to clk_set_parent(), but it's far less
used, and it doesn't look like there's any obvious user for that clock.
Similarly, it doesn't look like the device tree using that clock driver
uses any of the assigned-clock properties on that clock.
So, the set_parent hook is effectively unused, possibly because of an
oversight. However, it could also be an explicit decision by the
original author to avoid any reparenting but through an explicit call to
clk_set_parent().
The latter case would be equivalent to setting the determine_rate
implementation to clk_hw_determine_rate_no_reparent(). Indeed, if no
determine_rate implementation is provided, clk_round_rate() (through
clk_core_round_rate_nolock()) will call itself on the parent if
CLK_SET_RATE_PARENT is set, and will not change the clock rate
otherwise.
And if it was an oversight, then we are at least explicit about our
behavior now and it can be further refined down the line.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Samuel Holland <samuel@sholland.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rtc@vger.kernel.org
Cc: linux-sunxi@lists.linux.dev
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20221018-clk-range-checks-fixes-v4-45-971d5077e7d2@cerno.tech
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There is no more needs to use a dedicated wake up interrupt for RTC as
EXTI block manages by itself now all interrupt lines.
Dedicated wakeup interrupt has been introduced with STM32 MP1 support
commit b72252b658 ("rtc: stm32: add stm32mp1 rtc support") because GIC &
EXTI interrupts were not yet linked in EXTI driver.
Removing this interrupt won't break compatibility with device trees which
do use two interrupts entries: it could only prevent wakeup from low power
modes on STM32MP1x, but platform power management is not yet available.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20230531122732.1515594-1-amelie.delaunay@foss.st.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In a future patch HAS_IOPORT=n will result in inb()/outb() and friends
not being declared. We thus need to add HAS_IOPORT as dependency for
those drivers using them.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Acked-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/20230522105049.1467313-31-schnelle@linux.ibm.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230505121136.1185653-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Split rk808 into a core and an i2c part in preparation for
SPI support.
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> # for RTC
Tested-by: Diederik de Haas <didi.debian@cknow.org> # Rock64, Quartz64 Model A + B
Tested-by: Vincent Legoll <vincent.legoll@gmail.com> # Pine64 QuartzPro64
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230504173618.142075-6-sebastian.reichel@collabora.com
Signed-off-by: Lee Jones <lee@kernel.org>
- Add support for Renesas RZ/G2L MTU3
- New Device Support
- Add support for Lenovo Yoga Book X90F to Intel CHT WC
- Add support for MAX5970 and MAX5978 to Simple MFD (I2C)
- Add support for Meteor Lake PCH-S LPSS PCI to Intel LPSS PCI
- Add support for AXP15060 PMIC to X-Powers PMIC collection
- Remove Device Support
- Remove support for Samsung 5M8751 and S5M8763 PMIC devices
- New Functionality
- Convert deprecated QCOM IRQ Chip to config registers
- Add support for 32-bit address spaces to Renesas SMUs
- Fix-ups
- Make use of APIs / MACROs designed to simplify and demystify
- Add / improve Device Tree bindings
- Memory saving struct layout optimisations
- Remove old / deprecated functionality
- Factor out unassigned register addresses from ranges
- Trivial: Spelling fixes, renames and coding style fixes
- Rid 'defined but not used' warnings
- Remove ineffective casts and pointer stubs
- Bug Fixes
- Fix incorrectly non-inverted mask/unmask IRQs on QCOM platforms
- Remove MODULE_*() helpers from non-tristate drivers
- Do not attempt to use out-of-range memory addresses associated with io_base
- Provide missing export helpers
- Fix remap bulk read optimisation fallout
- Fix memory leak issues in error paths
-----BEGIN PGP SIGNATURE-----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=EBtX
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for Renesas RZ/G2L MTU3
New Device Support:
- Add support for Lenovo Yoga Book X90F to Intel CHT WC
- Add support for MAX5970 and MAX5978 to Simple MFD (I2C)
- Add support for Meteor Lake PCH-S LPSS PCI to Intel LPSS PCI
- Add support for AXP15060 PMIC to X-Powers PMIC collection
Remove Device Support:
- Remove support for Samsung 5M8751 and S5M8763 PMIC devices
New Functionality:
- Convert deprecated QCOM IRQ Chip to config registers
- Add support for 32-bit address spaces to Renesas SMUs
Fix-ups:
- Make use of APIs / MACROs designed to simplify and demystify
- Add / improve Device Tree bindings
- Memory saving struct layout optimisations
- Remove old / deprecated functionality
- Factor out unassigned register addresses from ranges
- Trivial: Spelling fixes, renames and coding style fixes
- Rid 'defined but not used' warnings
- Remove ineffective casts and pointer stubs
Bug Fixes:
- Fix incorrectly non-inverted mask/unmask IRQs on QCOM platforms
- Remove MODULE_*() helpers from non-tristate drivers
- Do not attempt to use out-of-range memory addresses associated with io_base
- Provide missing export helpers
- Fix remap bulk read optimisation fallout
- Fix memory leak issues in error paths"
* tag 'mfd-next-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (88 commits)
dt-bindings: mfd: ti,j721e-system-controller: Add SoC chip ID
leds: bd2606mvv: Driver for the Rohm 6 Channel i2c LED driver
dt-bindings: mfd: qcom,spmi-pmic: Document flash LED controller
dt-bindings: mfd: x-powers,axp152: Document the AXP15060 variant
mfd: axp20x: Add support for AXP15060 PMIC
dt-bindings: mfd: x-powers,axp152: Document the AXP313a variant
counter: rz-mtu3-cnt: Unlock on error in rz_mtu3_count_ceiling_write()
dt-bindings: mfd: dlg,da9063: Document voltage monitoring
dt-bindings: mfd: stm32: Remove unnecessary blank lines
dt-bindings: mfd: qcom,spmi-pmic: Use generic ADC node name in examples
dt-bindings: mfd: syscon: Add nuvoton,ma35d1-sys compatible
MAINTAINERS: Add entries for Renesas RZ/G2L MTU3a counter driver
counter: Add Renesas RZ/G2L MTU3a counter driver
Documentation: ABI: sysfs-bus-counter: add cascade_counts_enable and external_input_phase_clock_select
mfd: Add Renesas RZ/G2L MTU3a core driver
dt-bindings: timer: Document RZ/G2L MTU3a bindings
mfd: rsmu_i2c: Convert to i2c's .probe_new() again
mfd: intel-lpss: Add Intel Meteor Lake PCH-S LPSS PCI IDs
mfd: dln2: Fix memory leak in dln2_probe()
mfd: axp20x: Fix axp288 writable-ranges
...
Subsystem:
- Convert to platform remove callback returning void
Drivers:
- meson-vrtc: fix a firmware display issue
-----BEGIN PGP SIGNATURE-----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=i6d0
-----END PGP SIGNATURE-----
Merge tag 'rtc-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Not much this cycle, there is the conversion to remove_new and many
small fixes in drivers:
Subsystem:
- Convert to platform remove callback returning void
Drivers:
- meson-vrtc: fix a firmware display issue"
* tag 'rtc-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (53 commits)
rtc: armada38x: use devm_platform_ioremap_resource_byname()
rtc: sunplus: use devm_platform_ioremap_resource_byname()
rtc: jz4740: Make sure clock provider gets removed
rtc: k3: handle errors while enabling wake irq
rtc: meson-vrtc: Use ktime_get_real_ts64() to get the current time
dt-bindings: rtc: Drop unneeded quotes
rtc: pcf8523: remove unnecessary OR operation
rtc: pcf8523: fix coding-style issues
rtc: ds1390: mark OF related data as maybe unused
rtc: omap: include header for omap_rtc_power_off_program prototype
rtc: sun6i: Use of_property_present() for testing DT property presence
rtc: mpfs: convert SOC_MICROCHIP_POLARFIRE to ARCH_MICROCHIP_POLARFIRE
rtc: zynqmp: Convert to platform remove callback returning void
rtc: xgene: Convert to platform remove callback returning void
rtc: wm8350: Convert to platform remove callback returning void
rtc: vt8500: Convert to platform remove callback returning void
rtc: twl: Convert to platform remove callback returning void
rtc: tps6586x: Convert to platform remove callback returning void
rtc: tegra: Convert to platform remove callback returning void
rtc: sunplus: Convert to platform remove callback returning void
...
Convert platform_get_resource_byname(),devm_ioremap_resource() to a single
call to devm_platform_ioremap_resource_byname(), as this is exactly what
this function does.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/202303221130316049449@zte.com.cn
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Convert platform_get_resource_byname(),devm_ioremap_resource() to a single
call to devm_platform_ioremap_resource_byname(), as this is exactly what
this function does.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/202303221131581039486@zte.com.cn
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The jz4740 RTC driver registers a clock provider, but never removes it.
This leaves a stale clock provider behind that references freed clocks when
the device is unbound.
Use the managed `devm_of_clk_add_hw_provider()` instead of
`of_clk_add_hw_provider()` to make sure the provider gets automatically
removed on unbind.
Fixes: 5ddfa148de ("rtc: jz4740: Register clock provider for the CLK32K pin")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20230409162544.16155-1-lars@metafoo.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The S5M8763 MFD has no device tree compatible, and since board file
support for it was removed, there's no way to use this MFD. After
removing the remaining code for it from the MFD driver, also remove
support for it in the s5m RTC driver, and all remaining references to
it.
Signed-off-by: David Virag <virag.david003@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230131183008.4451-3-virag.david003@gmail.com
Due to the potential failure of enable_irq_wake(), it would be better to
return error if it fails.
Fixes: b09d633575 ("rtc: Introduce ti-k3-rtc")
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230323085904.957999-1-d-gole@ti.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The VRTC alarm register can be programmed with an amount of seconds
after which the SoC will be woken up by the VRTC timer again. We are
already converting the alarm time from meson_vrtc_set_alarm() to
"seconds since 1970". This means we also need to use "seconds since
1970" for the current time.
This fixes a problem where setting the alarm to one minute in the future
results in the firmware (which handles wakeup) to output (on the serial
console) that the system will be woken up in billions of seconds.
ktime_get_raw_ts64() returns the time since boot, not since 1970. Switch
to ktime_get_real_ts64() to fix the calculation of the alarm time and to
make the SoC wake up at the specified date/time. Also the firmware
(which manages suspend) now prints either 59 or 60 seconds until wakeup
(depending on how long it takes for the system to enter suspend).
Fixes: 6ef35398e8 ("rtc: Add Amlogic Virtual Wake RTC")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20230320212142.2355062-1-martin.blumenstingl@googlemail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The value variable is initialized to 0 and it is not used to set any
other bits rather than the one that defines the capacitor value. Setting
this capacitor value is the only purpose of the function where the
variable is defined and therefore the OR operation does not apply as a
way to foresee functionality extensions either.
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Link: https://lore.kernel.org/r/20230315082021.2104452-3-javier.carrasco@wolfvision.net
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Minor modifications for coding-style correctness (tabs, spaces and blank
lines before and after brackets). In total 7 errors, 3 warnings and 1
check where removed from the checkpatch output without damaging code
readability.
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Link: https://lore.kernel.org/r/20230315082021.2104452-2-javier.carrasco@wolfvision.net
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/rtc/rtc-ds1390.c:216:34: error: ‘ds1390_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230311111226.250922-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Non-static functions should have a prototype:
drivers/rtc/rtc-omap.c:410:5: error: no previous prototype for ‘omap_rtc_power_off_program’ [-Werror=missing-prototypes]
Fixes: 6256f7f7f2 ("rtc: OMAP: Add support for rtc-only mode")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230311094021.79730-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties. As
part of this, convert of_get_property/of_find_property calls to the
recently added of_property_present() helper when we just want to test
for presence of a property and nothing more.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20230310144736.1547041-1-robh@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
As part of converting RISC-V SOC_FOO symbols to ARCH_FOO to match the
use of such symbols on other architectures, convert the Microchip FPGA
RTC driver to use the new symbol.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230309204452.969574-5-conor@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-42-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-41-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230304133028.2135435-40-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-39-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-38-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-37-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-36-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-35-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-34-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-33-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-32-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-31-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-30-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230304133028.2135435-29-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-28-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-27-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-26-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-25-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-24-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-23-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-22-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-21-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-20-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230304133028.2135435-19-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-18-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-17-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230304133028.2135435-16-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-15-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-14-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230304133028.2135435-13-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-By: Joshua Kinard <kumba@gentoo.org>
Link: https://lore.kernel.org/r/20230304133028.2135435-12-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20230304133028.2135435-11-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-10-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-9-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-8-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230304133028.2135435-7-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230304133028.2135435-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230304133028.2135435-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The module pointer in class_create() never actually did anything, and it
shouldn't have been requred to be set as a parameter even if it did
something. So just remove it and fix up all callers of the function in
the kernel tree at the same time.
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20230313181843.1207845-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Subsystem:
- allow rtc_read_alarm without read_alarm callback
New driver:
- NXP BBNSM module RTC
Drivers:
- use IRQ flags from fwnode when available
- abx80x: nvmem support
- brcmstb-waketimer: add non-wake alarm support
- ingenic: provide CLK32K clock
- isl12022: cleanups
- moxart: switch to using gpiod API
- pcf85363: allow setting quartz load
- pm8xxx: cleanups and support for setting time
- rv3028, rv3032: add ACPI support
-----BEGIN PGP SIGNATURE-----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=aZkd
-----END PGP SIGNATURE-----
Merge tag 'rtc-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"A few drivers got some nice cleanups and a new driver are making the
bulk of the changes.
Subsystem:
- allow rtc_read_alarm without read_alarm callback
New driver:
- NXP BBNSM module RTC
Drivers:
- use IRQ flags from fwnode when available
- abx80x: nvmem support
- brcmstb-waketimer: add non-wake alarm support
- ingenic: provide CLK32K clock
- isl12022: cleanups
- moxart: switch to using gpiod API
- pcf85363: allow setting quartz load
- pm8xxx: cleanups and support for setting time
- rv3028, rv3032: add ACPI support"
* tag 'rtc-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (64 commits)
rtc: pm8xxx: add support for nvmem offset
dt-bindings: rtc: qcom-pm8xxx: add nvmem-cell offset
rtc: abx80x: Add nvmem support
rtc: rx6110: Remove unused of_gpio,h
rtc: efi: Avoid spamming the log on RTC read failure
rtc: isl12022: sort header inclusion alphabetically
rtc: isl12022: Join string literals back
rtc: isl12022: Drop unneeded OF guards and of_match_ptr()
rtc: isl12022: Explicitly use __le16 type for ISL12022_REG_TEMP_L
rtc: isl12022: Get rid of unneeded private struct isl12022
rtc: pcf85363: add support for the quartz-load-femtofarads property
dt-bindings: rtc: nxp,pcf8563: move pcf85263/pcf85363 to a dedicated binding
rtc: allow rtc_read_alarm without read_alarm callback
rtc: rv3032: add ACPI support
rtc: rv3028: add ACPI support
rtc: bbnsm: Add the bbnsm rtc support
rtc: jz4740: Register clock provider for the CLK32K pin
rtc: jz4740: Use dev_err_probe()
rtc: jz4740: Use readl_poll_timeout
dt-bindings: rtc: Add #clock-cells property
...
On many Qualcomm platforms the PMIC RTC control and time registers are
read-only so that the RTC time can not be updated. Instead an offset
needs be stored in some machine-specific non-volatile memory, which the
driver can take into account.
Add support for storing a 32-bit offset from the Epoch in an nvmem cell
so that the RTC time can be set on such platforms.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230202155448.6715-18-johan+linaro@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
