To get a better idea if underruns occurred during crtc disabling,
let's check for them explicitly. This helps in cases where the
error interrupt isn't active, or there is no underrun interrupt
support at all.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448050160-14124-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We sometimes get a spurious CPU pipe underrun somewhere between
enabling port A and enabling vdd for the panel. Observed on both
ILK and IVB with port A eDP. Suppress FIFO underrun reporting
around the port and vdd enable to avoid the dmesg errors.
Not sure if port D eDP would suffer from the same issue, but assume
that it doesn't until proven differently.
Testcase: igt/kms_setmode
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448050160-14124-2-git-send-email-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
We still get spurious pipe underruns on ILK/SNB/IVB under two
circumstances when dealing with PCH ports:
* When the pipe has been disabled, but FDI RX/TX is still enabled
* During FDI link training
Both cases seem to happen at least when we do VGA+HDMI cloning
from the same pipe. I don't think I've seen them when not cloning,
but can't be 100% sure.
Disable underrun reporting around those places to eliminate the
dmesg errors.
Testcase: igt/kms_setmode/basic-clone-single-crtc
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448050160-14124-1-git-send-email-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
It is not a bad idea to disable the PSR feature on Sink
when we are disabling on the Source.
v2: Move dpcd write inside mutex protected area as suggested by Sonika.
Cc: Sonika Jindal <sonika.jindal@intel.com>
Suggested-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Whenever DMC firmware put the HW into DC State a bunch
of registers including this perf counter is reset to 0.
Even with PSR active and working we could still read
"Performance_Counter: 0" what will misslead people to believe
PSR is broken. For instance on SKL we can only see PC10
residency with screen on if PSR is working properly.
However Performance_Counter was showing 0.
Even if it restored properly on DC6 exit we don't want to
give users the wrong impression that PSR is not working
while we know for sure it is.
So, it is better to remove this counter information while
we don't have a better way to track PSR residency.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we introduced PSR we let LPSP masked allowing us to get PSR
independently from the audio runtime PM. However in one of the
attempts to get PSR enabled by default one user reported one specific
case where he would miss screen updates if scrolling the firefox in a
Gnome environment when i915 runtime pm was enabled. So for
this specific case that (I could never create an i-g-t test case)
we decided to remove the LPSP mask and let HW tracking taking care of
this case. The mask got removed later by my
commit 09108b90f0 ("drm/i915: PSR: Remove Low Power HW tracking mask.")
So we started depending on audio driver again, what is bad.
With previous commit
"drm/i915: PSR: Let's rely more on frontbuffer tracking."
we transfered the PSR exit responsability totally to SW frontbuffer
tracking. So now can safelly shut off a bit the HW tracking, or
at least this case that makes us to depend on other drivers.
v2: Update commit message since this patch by itself doesn't solve
the bugzilla entries.
v3: Another attempt to improve commit message.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau damien.lespiau@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The ultimate goal here is to remove the dependency we
currently have on audio driver power to get PSR working.
Since with audio driver runtime PM disabled the Hardware tracking
believes graphics is fully active and prevent PSR Entry, or
in other words continuously exit PSR.
So, the idea is to transfer the PSR exit responsability
from the HW tracking to the SW tracking (frontbuffer tracking),
who is really mature right now.
However with LPSP masked out there might be cases where we could
miss exit from HW tracking since it can be relying on this,
like a specific case reported at our mailing list who
user reported he would miss screen updates if scrolling firefox
in a Gnome environment when i915 runtimepm was enabled.
So before masking out LPSP again to make us independent from
the audio driver we need to make sure that all our cases
are coverred from the frontbuffer tracking perspective,
where the flush means invalidate and flush.
Without this patch for HSW, BDW and SKL we just do the
invalidate part when the flush wasn't originated by a page flip
because we were trusting the HW tracking for the flip case.
So let's rely more on frontbuffer tracking and do the
invalidation regardless the origin as expected for all platforms.
v2: Improve commit message as suggested by Paulo.
v3: Another attempt to let commit message more clear.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau damien.lespiau@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit (89251b17) intended to remove this line and let only one
DP_PSR_EN_CFG set, but it was wrong and this call is now duplicated
at the code.
Also "& ~DP_PSR_MAIN_LINK_ACTIVE" doesn't do anything at all. It
was like that since I introduced this call but probably the idea
was to be informative and make clear statement that we were not using
the link standby. So it is better to remove this one here and let
the code a bit cleaner.
v2: Improve commit message as requested by Paulo.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau damien.lespiau@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit e9f24d5fb7
Author: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Date: Mon Oct 5 13:26:36 2015 +0100
drm/i915: Clean up associated VMAs on context destruction
Added a warning based on an incorrect assumption that all VMAs
in a VM will be on the inactive list at the point last reference
to a context and VM is dropped.
This is not true because i915_gem_object_retire__read will not
put VMA on the inactive list until all activities on the object
in question (in all VMs) have been retired.
As a consequence, whether or not a context/VM will be destroyed
with its VMAs still on the active list, can depend on completely
unrelated activities using the same object from a different
context or engine.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92638
Testcase: igt/gem_request_retire/retire-vma-not-inactive
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448025816-25584-1-git-send-email-tvrtko.ursulin@linux.intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we experience a refcounting failure in a power domain/well (unref'ing at
least one too many times), log the name of the offending domain or well.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448034934-11926-2-git-send-email-daniels@collabora.com
Let us print human-parseable values from the power domain code; upcoming
display code also wants to use it.
This requires moving it out of i915_debugfs.c, as that is only conditionally
compiled.
v2: Move it out of the header.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448034934-11926-1-git-send-email-daniels@collabora.com
During suspend-to-idle we need to keep the DMC firmware active and DC6
enabled, since otherwise we won't reach deep system power states like
PC9/10. The lead for this came from Nivedita who noticed that the
kernel's turbostat tool didn't report any PC9/10 residency change
across an 'echo freeze > /sys/power/state'.
Reported-by: Nivedita Swaminathan <nivedita.swaminathan@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447860750-18110-1-git-send-email-imre.deak@intel.com
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWUmHZAAoJEHm+PkMAQRiGHtcH/RVRsn8re0WdRWYaTr9+Hknm
CGlRJN4LKecttgYQ/2bS1QsDbt8usDPBiiYVopqGXQxPBmjyDAqPjsa+8VzCaVc6
WA+9LDB+PcW28lD6BO+qSZCOAm7hHSZq7dtw9x658IqO+mI2mVeCybsAyunw2iWi
Kf5q90wq6tIBXuT8YH9MXGrSCQw00NclbYeYwB9CmCt9hT/koEFBdl7uFUFitB+Q
GSPTz5fXhgc5Lms85n7flZlrVKoQKmtDQe4/DvKZm+SjsATHU9ru89OxDBdS5gSG
YcEIM4zc9tMjhs3GC9t6WXf6iFOdctum8HOhUoIN/+LVfeOMRRwAhRVqtGJ//Xw=
=DCUg
-----END PGP SIGNATURE-----
Merge tag 'v4.4-rc2' into drm-intel-next-queued
Linux 4.4-rc2
Backmerge to get at
commit 1b0e3a049e
Author: Imre Deak <imre.deak@intel.com>
Date: Thu Nov 5 23:04:11 2015 +0200
drm/i915/skl: disable display side power well support for now
so that we can proplery re-eanble skl power wells in -next.
Conflicts are just adjacent lines changed, except for intel_fbdev.c
where we need to interleave the changs. Nothing nefarious.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Merge slub bulk allocator updates from Andrew Morton:
"This missed the merge window because I was waiting for some repairs to
come in. Nothing actually uses the bulk allocator yet and the changes
to other code paths are pretty small. And the net guys are waiting
for this so they can start merging the client code"
More comments from Jesper Dangaard Brouer:
"The kmem_cache_alloc_bulk() call, in mm/slub.c, were included in
previous kernel. The present version contains a bug. Vladimir
Davydov noticed it contained a bug, when kernel is compiled with
CONFIG_MEMCG_KMEM (see commit 03ec0ed57f: "slub: fix kmem cgroup
bug in kmem_cache_alloc_bulk"). Plus the mem cgroup counterpart in
kmem_cache_free_bulk() were missing (see commit 033745189b "slub:
add missing kmem cgroup support to kmem_cache_free_bulk").
I don't consider the fix stable-material because there are no in-tree
users of the API.
But with known bugs (for memcg) I cannot start using the API in the
net-tree"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
slab/slub: adjust kmem_cache_alloc_bulk API
slub: add missing kmem cgroup support to kmem_cache_free_bulk
slub: fix kmem cgroup bug in kmem_cache_alloc_bulk
slub: optimize bulk slowpath free by detached freelist
slub: support for bulk free with SLUB freelists
Here are a few small tty/serial driver fixes for 4.4-rc2 that resolve
some reported problems.
All have been in linux-next, full details are in the shortlog below.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlZSCjgACgkQMUfUDdst+yl4kQCgyYYsaVVUcG2i3HQUpio4CAJg
EFQAn03Z0OD/EGNHKw7FtsICSgAhSatG
=JRcn
-----END PGP SIGNATURE-----
Merge tag 'tty-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are a few small tty/serial driver fixes for 4.4-rc2 that resolve
some reported problems.
All have been in linux-next, full details are in the shortlog below"
* tag 'tty-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: export fsl8250_handle_irq
serial: 8250_mid: Add missing dependency
tty: audit: Fix audit source
serial: etraxfs-uart: Fix crash
serial: fsl_lpuart: Fix earlycon support
bcm63xx_uart: Use the device name when registering an interrupt
tty: Fix direct use of tty buffer work
tty: Fix tty_send_xchar() lock order inversion
Here are some staging and iio driver fixes for 4.4-rc2. All of these
are in response to issues that have been reported and have been in
linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlZSCfgACgkQMUfUDdst+yn0cwCeI7I/i1MUaiequc4gSOoElqfa
RCYAnj+PTk+BcbACs0mgZKbYuEEd1eVT
=nUNA
-----END PGP SIGNATURE-----
Merge tag 'staging-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO fixes from Greg KH:
"Here are some staging and iio driver fixes for 4.4-rc2. All of these
are in response to issues that have been reported and have been in
linux-next for a while"
* tag 'staging-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Revert "Staging: wilc1000: coreconfigurator: Drop unneeded wrapper functions"
iio: adc: xilinx: Fix VREFN scale
iio: si7020: Swap data byte order
iio: adc: vf610_adc: Fix division by zero error
iio:ad7793: Fix ad7785 product ID
iio: ad5064: Fix ad5629/ad5669 shift
iio:ad5064: Make sure ad5064_i2c_write() returns 0 on success
iio: lpc32xx_adc: fix warnings caused by enabling unprepared clock
staging: iio: select IRQ_WORK for IIO_DUMMY_EVGEN
vf610_adc: Fix internal temperature calculation
Here are a number of USB fixes and new device ids for 4.4-rc2. All have
been in linux-next and the details are in the shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlZSDW4ACgkQMUfUDdst+ymrlwCgha5PobWYrhVnhC/w5ODZxRaF
oAQAn2tOK94L9sADvjbQlFUy+/Zaxxbj
=x9f4
-----END PGP SIGNATURE-----
Merge tag 'usb-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB fixes and new device ids for 4.4-rc2. All
have been in linux-next and the details are in the shortlog"
* tag 'usb-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (28 commits)
usblp: do not set TASK_INTERRUPTIBLE before lock
USB: MAINTAINERS: cxacru
usb: kconfig: fix warning of select USB_OTG
USB: option: add XS Stick W100-2 from 4G Systems
xhci: Fix a race in usb2 LPM resume, blocking U3 for usb2 devices
usb: xhci: fix checking ep busy for CFC
xhci: Workaround to get Intel xHCI reset working more reliably
usb: chipidea: imx: fix a possible NULL dereference
usb: chipidea: usbmisc_imx: fix a possible NULL dereference
usb: chipidea: otg: gadget module load and unload support
usb: chipidea: debug: disable usb irq while role switch
ARM: dts: imx27.dtsi: change the clock information for usb
usb: chipidea: imx: refine clock operations to adapt for all platforms
usb: gadget: atmel_usba_udc: Expose correct device speed
usb: musb: enable usb_dma parameter
usb: phy: phy-mxs-usb: fix a possible NULL dereference
usb: dwc3: gadget: let us set lower max_speed
usb: musb: fix tx fifo flush handling
usb: gadget: f_loopback: fix the warning during the enumeration
usb: dwc2: host: Fix remote wakeup when not in DWC2_L2
...
Pull MIPS fixes from Ralf Baechle:
- Fix a flood of annoying build warnings
- A number of fixes for Atheros 79xx platforms
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: ath79: Add a machine entry for booting OF machines
MIPS: ath79: Fix the size of the MISC INTC registers in ar9132.dtsi
MIPS: ath79: Fix the DDR control initialization on ar71xx and ar934x
MIPS: Fix flood of warnings about comparsion being always true.
Pull parisc update from Helge Deller:
"This patchset adds Huge Page and HUGETLBFS support for parisc"
Honestly, the hugepage support should have gone through in the merge
window, and is not really an rc-time fix. But it only touches
arch/parisc, and I cannot find it in myself to care. If one of the
three parisc users notices a breakage, I will point at Helge and make
rude farting noises.
* 'parisc-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Map kernel text and data on huge pages
parisc: Add Huge Page and HUGETLBFS support
parisc: Use long branch to do_syscall_trace_exit
parisc: Increase initial kernel mapping to 32MB on 64bit kernel
parisc: Initialize the fault vector earlier in the boot process.
parisc: Add defines for Huge page support
parisc: Drop unused MADV_xxxK_PAGES flags from asm/mman.h
parisc: Drop definition of start_thread_som for HP-UX SOM binaries
parisc: Fix wrong comment regarding first pmd entry flags
Pull perf tool fixes from Thomas Gleixner:
"A couple of fixes for perf tools:
- Build system updates
- Plug a memory leak in an error path of perf probe
- Tear down probes correctly when adding fails
- Fixes to the perf symbol handling
- Fix ordering of event processing in buildid-list
- Fix per DSO filtering in the histogram browser"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf probe: Clear probe_trace_event when add_probe_trace_event() fails
perf probe: Fix memory leaking on failure by clearing all probe_trace_events
perf inject: Also re-pipe lost_samples event
perf buildid-list: Requires ordered events
perf symbols: Fix dso lookup by long name and missing buildids
perf symbols: Allow forcing reading of non-root owned files by root
perf hists browser: The dso can be obtained from popup_action->ms.map->dso
perf hists browser: Fix 'd' hotkey action to filter by DSO
perf symbols: Rebuild rbtree when adjusting symbols for kcore
tools: Add a "make all" rule
tools: Actually install tmon in the install rule
Pull x86 fixes from Thomas Gleixner:
"This update contains:
- MPX updates for handling 32bit processes
- A fix for a long standing bug in 32bit signal frame handling
related to FPU/XSAVE state
- Handle get_xsave_addr() correctly in KVM
- Fix SMAP check under paravirtualization
- Add a comment to the static function trace entry to avoid further
confusion about the difference to dynamic tracing"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Fix SMAP check in PVOPS environments
x86/ftrace: Add comment on static function tracing
x86/fpu: Fix get_xsave_addr() behavior under virtualization
x86/fpu: Fix 32-bit signal frame handling
x86/mpx: Fix 32-bit address space calculation
x86/mpx: Do proper get_user() when running 32-bit binaries on 64-bit kernels
Adjust kmem_cache_alloc_bulk API before we have any real users.
Adjust API to return type 'int' instead of previously type 'bool'. This
is done to allow future extension of the bulk alloc API.
A future extension could be to allow SLUB to stop at a page boundary, when
specified by a flag, and then return the number of objects.
The advantage of this approach, would make it easier to make bulk alloc
run without local IRQs disabled. With an approach of cmpxchg "stealing"
the entire c->freelist or page->freelist. To avoid overshooting we would
stop processing at a slab-page boundary. Else we always end up returning
some objects at the cost of another cmpxchg.
To keep compatible with future users of this API linking against an older
kernel when using the new flag, we need to return the number of allocated
objects with this API change.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Initial implementation missed support for kmem cgroup support in
kmem_cache_free_bulk() call, add this.
If CONFIG_MEMCG_KMEM is not enabled, the compiler should be smart enough
to not add any asm code.
Incoming bulk free objects can belong to different kmem cgroups, and
object free call can happen at a later point outside memcg context. Thus,
we need to keep the orig kmem_cache, to correctly verify if a memcg object
match against its "root_cache" (s->memcg_params.root_cache).
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The call slab_pre_alloc_hook() interacts with kmemgc and is not allowed to
be called several times inside the bulk alloc for loop, due to the call to
memcg_kmem_get_cache().
This would result in hitting the VM_BUG_ON in __memcg_kmem_get_cache.
As suggested by Vladimir Davydov, change slab_post_alloc_hook() to be able
to handle an array of objects.
A subtle detail is, loop iterator "i" in slab_post_alloc_hook() must have
same type (size_t) as size argument. This helps the compiler to easier
realize that it can remove the loop, when all debug statements inside loop
evaluates to nothing. Note, this is only an issue because the kernel is
compiled with GCC option: -fno-strict-overflow
In slab_alloc_node() the compiler inlines and optimizes the invocation of
slab_post_alloc_hook(s, flags, 1, &object) by removing the loop and access
object directly.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reported-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Suggested-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Reviewed-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make it possible to free a freelist with several objects by adjusting API
of slab_free() and __slab_free() to have head, tail and an objects counter
(cnt).
Tail being NULL indicate single object free of head object. This allow
compiler inline constant propagation in slab_free() and
slab_free_freelist_hook() to avoid adding any overhead in case of single
object free.
This allows a freelist with several objects (all within the same
slab-page) to be free'ed using a single locked cmpxchg_double in
__slab_free() and with an unlocked cmpxchg_double in slab_free().
Object debugging on the free path is also extended to handle these
freelists. When CONFIG_SLUB_DEBUG is enabled it will also detect if
objects don't belong to the same slab-page.
These changes are needed for the next patch to bulk free the detached
freelists it introduces and constructs.
Micro benchmarking showed no performance reduction due to this change,
when debugging is turned off (compiled with CONFIG_SLUB_DEBUG).
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds huge page support to allow userspace to allocate huge
pages and to use hugetlbfs filesystem on 32- and 64-bit Linux kernels.
A later patch will add kernel support to map kernel text and data on
huge pages.
The only requirement is, that the kernel needs to be compiled for a
PA8X00 CPU (PA2.0 architecture). Older PA1.X CPUs do not support
variable page sizes. 64bit Kernels are compiled for PA2.0 by default.
Technically on parisc multiple physical huge pages may be needed to
emulate standard 2MB huge pages.
Signed-off-by: Helge Deller <deller@gmx.de>
Use the 22bit instead of the 17bit branch instruction on a 64bit kernel
to reach the do_syscall_trace_exit function from the gateway page.
A huge page enabled kernel may need the additional branch distance bits.
Signed-off-by: Helge Deller <deller@gmx.de>
For the 64bit kernel the initially 16 MB kernel memory might become too
small if you build a kernel with many modules built-in and with kernel
text and data areas mapped on huge pages.
This patch increases the initial mapping to 32MB for 64bit kernels and
keeps 16MB for 32bit kernels.
Signed-off-by: Helge Deller <deller@gmx.de>
A fault vector on parisc needs to be 2K aligned. Furthermore the
checksum of the fault vector needs to sum up to 0 which is being
calculated and written at runtime.
Up to now we aligned both PA20 and PA11 fault vectors on the same 4K
page in order to easily write the checksum after having mapped the
kernel read-only (by mapping this page only as read-write).
But when we want to map the kernel text and data on huge pages this
makes things harder.
So, simplify it by aligning both fault vectors on 2K boundries and write
the checksum before we map the page read-only.
Signed-off-by: Helge Deller <deller@gmx.de>
Huge pages on parisc will have the same size as one pmd table, which
is on a 64bit kernel 2MB on a kernel with 4K kernel page sizes, and
on a 32bit kernel 4MB when used with 4K kernel pages.
Since parisc does not physically supports 2MB huge page sizes, emulate
it with two consecutive 1MB page sizes instead. Keeping the same huge
page size as one pmd will allow us to add transparent huge page support
later on.
Bit 21 in the pte flags was unused and will now be used to mark a page
as huge page (_PAGE_HPAGE_BIT).
Signed-off-by: Helge Deller <deller@gmx.de>
Drop the MADV_xxK_PAGES flags, which were never used and were from a proposed
API which was never integrated into the generic Linux kernel code.
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
Merge misc fixes from Andrew Morton:
"A bunch of fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
slub: mark the dangling ifdef #else of CONFIG_SLUB_DEBUG
slub: avoid irqoff/on in bulk allocation
slub: create new ___slab_alloc function that can be called with irqs disabled
mm: fix up sparse warning in gfpflags_allow_blocking
ocfs2: fix umask ignored issue
PM/OPP: add entry in MAINTAINERS
kernel/panic.c: turn off locks debug before releasing console lock
kernel/signal.c: unexport sigsuspend()
kasan: fix kmemleak false-positive in kasan_module_alloc()
fat: fix fake_offset handling on error path
mm/hugetlbfs: fix bugs in fallocate hole punch of areas with holes
mm/page-writeback.c: initialize m_dirty to avoid compile warning
various: fix pci_set_dma_mask return value checking
mm: loosen MADV_NOHUGEPAGE to enable Qemu postcopy on s390
mm: vmalloc: don't remove inexistent guard hole in remove_vm_area()
tools/vm/page-types.c: support KPF_IDLE
ncpfs: don't allow negative timeouts
configfs: allow dynamic group creation
MAINTAINERS: add Moritz as reviewer for FPGA Manager Framework
slab.h: sprinkle __assume_aligned attributes
Pull timer fixes from Thomas Gleixner:
"Two timer fixlets from Arnd:
- Use proper constant size in the FSL timer driver
- Prevent a build error for legacy platforms"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: Disallow drivers for ARCH_USES_GETTIMEOFFSET
clocksource/fsl: Avoid harmless 64-bit warnings
Pull irq fixes from Thomas Gleixner:
"Three fixes for the ARM GIC interrupt controller from Marc addressing
various shortcomings versus boot initialization and suspend/resume"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic: Add save/restore of the active state
irqchip/gic: Clear enable bits before restoring them
irqchip/gic: Make sure all interrupts are deactivated at boot
* MAINTAINERS updates for brcmnand driver
* Fix reboot hangs seen when multiple NAND flash chips are registered with the
same controller
* Fix build issues on jz4740 NAND driver; the error was introduced in 4.3, so
I guess nobody really cared, but we might as well fix it
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8XN+
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20151120' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
- MAINTAINERS updates for brcmnand driver
- Fix reboot hangs seen when multiple NAND flash chips are registered
with the same controller
- Fix build issues on jz4740 NAND driver; the error was introduced in
4.3, so I guess nobody really cared, but we might as well fix it
* tag 'for-linus-20151120' of git://git.infradead.org/linux-mtd:
MAINTAINERS: brcmnand: Add co-maintainer for Broadcom SoCs
MAINTAINERS: brcmnand: Add Broadcom internal mailing-list
mtd: nand: fix shutdown/reboot for multi-chip systems
mtd: jz4740_nand: fix build on jz4740 after removing gpio.h
fsl8250_handle_irq is now used by the of_serial driver, and that fails
if it is a loadable module:
ERROR: "fsl8250_handle_irq" [drivers/tty/serial/of_serial.ko] undefined!
This exports the symbol to avoid randconfig errors.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d43b54d269 ("serial: Enable Freescale 16550 workaround on arm")
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250_mid uses rational_best_approximation() function, so the
driver needs to select CONFIG_RATIONAL option.
This fixes build error when CONFIG_RATIONAL is not enabled:
drivers/built-in.o: In function `mid8250_set_termios':
8250_mid.c:(.text+0x10169a): undefined reference to `rational_best_approximation'
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The data to audit/record is in the 'from' buffer (ie., the input
read buffer).
Fixes: 72586c6061 ("n_tty: Fix auditing support for cannonical mode")
Cc: stable <stable@vger.kernel.org> # 4.1+
Cc: Miloslav Trmač <mitr@redhat.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Earlycon support for Freescale lpuart should only be enabled when
console support is enabled.
Fixes: 1d59b382f1 ("serial: fsl_lpuart: add earlycon support")
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the device name when registering an interrupt so that multiple
ports don't all have the same interrupt name.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recent abstraction of tty buffer work introduced api to manage
tty input kworker; use it.
Fixes: e176058f0d ("tty: Abstract tty buffer work")
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The correct lock order is atomic_write_lock => termios_rwsem, as
established by tty_write() => n_tty_write().
Fixes: c274f6ef1c ("tty: Hold termios_rwsem for tcflow(TCIxxx)")
Reported-and-Tested-by: Dmitry Vyukov <dvyukov@google.com>
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The #ifdef of CONFIG_SLUB_DEBUG is located very far from the associated
#else. For readability mark it with a comment.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the new function that can do allocation while interrupts are disabled.
Avoids irq on/off sequences.
Signed-off-by: Christoph Lameter <cl@linux.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
