DPC thread can stall during switch scan due to slow switch response.
This will stall other work element that needs attention. Moving work
element processing and relogin logic out of DPC thread and into its
own work queue.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace call to Get Port DataBase MB with PDO_FORCE_ADISC
flag with async ADISC command so driver can see ADISC command
has error or not.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adjusts and reallocates fw_dump memory for target mode
to save for extended login and exchange offload buffers into
dump captured.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As part of chip reset, all commands from all QPairs are
flushed. This patch fixes code to use Q Pair lock for flush
instead of using old hardware_lock.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Max boundary for exchange off load is 32k exchanges. If a system
is unable to allocate large memory buffer to support this feature,
then driver will reduce the number of exchanges down to a value
system can support.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current code uses Stop Firmware MB cmd to stop the chip before
driver unload. This will leave the laser in its current state.
This give the illusion of this adapter is still alive.
For 8G & newer adapters, use chip reset to stop the chip and
bring down the laser.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use IOCB patch to submit Control VP MBX command to reduce
bottle-neck for mbx interface.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
when processing iocb in a timeout case, driver was trying to log messages
without verifying if the fcport structure could have valid data. This
results in a NULL pointer access.
Fixes: 726b85487067("qla2xxx: Add framework for async fabric discovery")
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
hpsa_show_dev_msg prints other information and a newline after the
message string, so the message string does not need to include a newline
explicitly. Done using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update driver Version to 50877
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Earlier driver would scan throgh all supported buses and targets and add
devices that responded. It would add devices that were _hidden_ by the fw.
Driver would invalidate commands sent to _hidden_ devices via the
AAC_HIDE_DISK check.
Since the driver now adds only the devices that are supposed to be
exposed, this code can be removed.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a chance of the driver to be stuck in kdump if drives start
acting up in kdump discovery process and the kernel decides to send eh
resets, which would prompt rescan to be scheduled.
Do not perform a rescan in kdump context, since we do not expect a hotplug
event during kdump and all the devices are going to go away anyway.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add back the ability to scan for hotplug changes while eh was in progress.
Schedule a rescan for a later time in the eh recovery code and wait for
eh to complete in the rescan worker.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the driver fails to retrieve information from the fw (could happen when
the fw is not fully in its senses), the driver does nothing and change is
not processed correctly by the driver
Schedule host rescan in case of failure. This is only for SAFW, since
the information retrieval failure will happen on SAFW devices.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver uses scsi_scan_host to add new devices in the driver init path,
which adds all the fw exposed devices. The drivers resorts to queue
command checks to block out commands to _hidden_ devices.
Use the hotplug handler code to add new devices during driver init and
other areas, this is only for safw. For ARC scsi_scan_host will still
apply.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently driver will attempt to process hotplug events concurrently based
on the FW interrupt.
Protect safw update function with a scan mutex.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The device hotplug events are processed only after retrieving the updated
lun information from the fw. Does not make sense to keep them separate.
Merge both the hotplug handling and safw adapter setup code into single
function.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Resolve luns checks the if a sdev is already present in the os to figure
out if it needs to be removed. Internally the driver exposes HBA on bus
2 even though its bus 1 in the fw. Its mildly confusing.
Refactor out the sdev lookup into its function to check if sdev has been
added to the kernel or not. Add helper functions to add, remove and put
devices based on their fw bus and target number.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added macros to loop through the MAX SUPPORTED Buses and Targets. This
will make the code a bit easier to read.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The hotplug handler code is duplicated for hba handling and container
handling.
Merged function to handle hba and container hot plug events into the
resolve luns functions. Added a bunch of helper functions to check the
validity of a given target and to check if bus, target is container
device.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Merge aac_get_containers to setup target function, so that information
about all the present devices can be retrieved in one shot.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add helper function to set queue depth from information retrieved from
the bmic phy structure.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Save the bmic information for each phy, so that it can processed in
target setup function.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Created inline function to retrieve lun info for each device from the
phy luns structure.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move the function to get phy luns information to the top of function
to set target information
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove function call to process targets from the report phy luns function
and make it a function in its own right. This will help understand the
flow of the code.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add helper function to setup targets devices and create the base for the
upcoming patches
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename variables and functions to make bmic identify, report phy luns
to make them consistent across code internal existing code bases
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Edit function that retrieves phy lun information to use common
bmic function
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
safw command submission is duplicated across many functions.
Move the safw submission code from bmic identify into its own function
for common use
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ideally driver needs to wait for IO to be submitted or responded to before
shutdown.
Move code to wait for IO completion into shutdown path
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Refactored the reset_host store function to make consistent across code
bases
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It is possible to restart the controller via the use of the reset_host
sysfs variable. This does work for controllers that can no longer respond,
since driver will attempt to send down a shutdown in this path.
Check if the controller is able to receive commands before sending down
a shutdown
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver would hang when attempting to send reset from the ioctl interface,
since it would wait to retrieve the ioctl mutex at send shutdown.
Set adapter shutdown and unlock mutex before sending down reset request.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As part of the recovery process, the drivers removes offline devices (
done by the kernel) and then tries to add them back in the rescan code.
Removing the device is like taking a sledgehammer to a nail.
Set the device as running if it is marked offline.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver attempts to perform a device scan and device add after coming out
of reset. At times when the kdump kernel loads and it tries to perform
eh recovery, the device scan hangs since its commands are blocked because
of the eh recovery. This should have shown up in normal eh recovery path
(Should have been obvious)
Remove the code that performs scanning.I can live without the rescanning
support in the stable kernels but a hanging kdump/eh recovery needs to be
fixed.
Fixes: a2d0321dd5 (scsi: aacraid: Reload offlined drives after controller reset)
Cc: <stable@vger.kernel.org>
Reported-by: Douglas Miller <dougmill@linux.vnet.ibm.com>
Tested-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Fixes: a2d0321dd5 (scsi: aacraid: Reload offlined drives after controller reset)
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Check if the adapter can receive abort requests, before sending aborts
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When udev requests for a devices inquiry string, it might create multiple
threads causing a race condition on the shared inquiry resource string.
Created a buffer with the string for each thread.
Cc: <stable@vger.kernel.org>
Fixes: 3bc8070fb7 ([SCSI] aacraid: SMC vendor identification)
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix kernel-doc warnings in drivers/scsi/ that are related to iscsi
support interfaces.
Fixes these kernel-doc warnings: (tested by adding these files to a new
target.rst documentation file: WIP)
../drivers/scsi/libiscsi.c:2740: warning: No description found for parameter 'dd_size'
../drivers/scsi/libiscsi.c:2740: warning: No description found for parameter 'id'
../drivers/scsi/libiscsi.c:2961: warning: No description found for parameter 'cls_conn'
../drivers/scsi/iscsi_tcp.c:313: warning: No description found for parameter 'conn'
../drivers/scsi/iscsi_tcp.c:363: warning: No description found for parameter 'conn'
../drivers/scsi/libiscsi_tcp.c:810: warning: No description found for parameter 'tcp_conn'
../drivers/scsi/libiscsi_tcp.c:810: warning: No description found for parameter 'segment'
../drivers/scsi/libiscsi_tcp.c:887: warning: No description found for parameter 'offloaded'
../drivers/scsi/libiscsi_tcp.c:887: warning: No description found for parameter 'status'
../drivers/scsi/libiscsi_tcp.c:887: warning: Excess function parameter 'offload' description in 'iscsi_tcp_recv_skb'
../drivers/scsi/libiscsi_tcp.c:964: warning: Excess function parameter 'conn' description in 'iscsi_tcp_task_init'
../drivers/scsi/libiscsi_tcp.c:964: warning: Excess function parameter 'sc' description in 'iscsi_tcp_task_init'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "Nicholas A. Bellinger" <nab@linux-iscsi.org>
Cc: linux-scsi@vger.kernel.org
Cc: target-devel@vger.kernel.org
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: linux-rdma@vger.kernel.org
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1. In IO path, setting of "ATA command pending" flag early before device
removal, invalid device handle etc., checks causes any new commands
to be always returned with SAM_STAT_BUSY and when the driver removes
the drive the SML issues SYNC Cache command and that command is
always returned with SAM_STAT_BUSY and thus making SYNC Cache command
to requeued.
2. If the driver gets an ATA PT command for a SATA drive then the driver
set "ATA command pending" flag in device specific data structure not
to allow any further commands until the ATA PT command is completed.
However, after setting the flag if the driver decides to return the
command back to upper layers without actually issuing to the firmware
(i.e., returns from qcmd failure return paths) then the corresponding
flag is not cleared and this prevents the driver from sending any new
commands to the drive.
This patch fixes above two issues by setting of "ATA command pending"
flag after checking for whether device deleted, invalid device handle,
device busy with task management. And by setting "ATA command pending"
flag to false in all of the qcmd failure return paths after setting the
flag.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Several statements are indented too far, fix these
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
localport is being dereferenced to assign lport and then immediately
afterwards localport is being sanity checked to see if it is null. Fix
this by only dereferencing localport until after it has been null
checked.
Detected by CoverityScan, CID#1463038 ("Dereference before null check")
Fixes: 3a8cefbfc5ee ("scsi: lpfc: Beef up stat counters for debug")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The define names specified 64Bit/128Bit, not 64GBIT/128GBIT. Correct
the names.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The function sas_parse_addr() could be easily substituted by hex2bin()
which is in kernel library code.
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If, for any reason, userland shuts down iscsi transport interfaces
before proper logouts - like when logging in to LUNs manually, without
logging out on server shutdown, or when automated scripts can't
umount/logout from logged LUNs - kernel will hang forever on its
sd_sync_cache() logic, after issuing the SYNCHRONIZE_CACHE cmd to all
still existent paths.
PID: 1 TASK: ffff8801a69b8000 CPU: 1 COMMAND: "systemd-shutdow"
#0 [ffff8801a69c3a30] __schedule at ffffffff8183e9ee
#1 [ffff8801a69c3a80] schedule at ffffffff8183f0d5
#2 [ffff8801a69c3a98] schedule_timeout at ffffffff81842199
#3 [ffff8801a69c3b40] io_schedule_timeout at ffffffff8183e604
#4 [ffff8801a69c3b70] wait_for_completion_io_timeout at ffffffff8183fc6c
#5 [ffff8801a69c3bd0] blk_execute_rq at ffffffff813cfe10
#6 [ffff8801a69c3c88] scsi_execute at ffffffff815c3fc7
#7 [ffff8801a69c3cc8] scsi_execute_req_flags at ffffffff815c60fe
#8 [ffff8801a69c3d30] sd_sync_cache at ffffffff815d37d7
#9 [ffff8801a69c3da8] sd_shutdown at ffffffff815d3c3c
This happens because iscsi_eh_cmd_timed_out(), the transport layer
timeout helper, would tell the queue timeout function (scsi_times_out)
to reset the request timer over and over, until the session state is
back to logged in state. Unfortunately, during server shutdown, this
might never happen again.
Other option would be "not to handle" the issue in the transport
layer. That would trigger the error handler logic, which would also need
the session state to be logged in again.
Best option, for such case, is to tell upper layers that the command was
handled during the transport layer error handler helper, marking it as
DID_NO_CONNECT, which will allow completion and inform about the
problem.
After the session was marked as ISCSI_STATE_FAILED, due to the first
timeout during the server shutdown phase, all subsequent cmds will fail
to be queued, allowing upper logic to fail faster.
Signed-off-by: Rafael David Tinoco <rafael.tinoco@canonical.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Prior patch mixed up what argument in the macro was what, so min value
was placed as the "default" argument, and the default value was placed
as the "min" argument. Thus, when the default was applied, it looked
like the default was smaller than the allowed min.
Swap argument postions to correct.
[mkp: fixed checkpatch warning]
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes following warnings reported by smatch:
drivers/scsi/qla2xxx/qla_mid.c:586 qla25xx_delete_req_que()
error: we previously assumed 'req' could be null (see line 580)
drivers/scsi/qla2xxx/qla_mid.c:602 qla25xx_delete_rsp_que()
error: we previously assumed 'rsp' could be null (see line 596)
Fixes: 7867b98dce ("scsi: qla2xxx: Fix memory leak in dual/target mode")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver may sleep under a spinlock.
The function call path is:
qedi_cpu_offline (acquire the spinlock)
qedi_fp_process_cqes
qedi_mtask_completion
qedi_process_tmf_resp
kzalloc(GFP_KERNEL) --> may sleep
To fix it, GFP_KERNEL is replaced with GFP_ATOMIC.
This bug is found by my static analysis tool(DSAC) and checked by my
code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
