This updates all the defconfigs in arch/powerpc/configs except iseries
and ps3, which were updated by the preceding commits.
This mostly takes the defaults, except that I turned on tickless idle
and high-resolution timers for everything, and turned off instrumentation
support and "Fair group CPU scheduler" for the smaller/embedded platforms.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The notable changes here are the enabling of NO_HZ and HIGH_RES_TIMERS.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The commit fa13a5a1f2 (sched: restore
deterministic CPU accounting on powerpc), unconditionally calls
update_process_tick() in system context. In the deterministic
accounting case this is the correct thing to do. However, in the
non-deterministic accounting case we need to not do this, since doing
this results in the time accounted as hardware irq time being
artificially elevated.
Also this collapses 2 consecutive '#ifdef CONFIG_VIRT_CPU_ACCOUNTING'
checks in time.h into one for neatness.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
VM/Security: add security hook to do_brk
Security: round mmap hint address above mmap_min_addr
security: protect from stack expantion into low vm addresses
Security: allow capable check to permit mmap or low vm space
SELinux: detect dead booleans
SELinux: do not clear f_op when removing entries
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
[LRO]: fix lro_gen_skb() alignment
[TCP]: NAGLE_PUSH seems to be a wrong way around
[TCP]: Move prior_in_flight collect to more robust place
[TCP] FRTO: Use of existing funcs make code more obvious & robust
[IRDA]: Move ircomm_tty_line_info() under #ifdef CONFIG_PROC_FS
[ROSE]: Trivial compilation CONFIG_INET=n case
[IPVS]: Fix sched registration race when checking for name collision.
[IPVS]: Don't leak sysctl tables if the scheduler registration fails.
endianness annotations in networking code had been in place for quite a
while; in particular, sin_port and s_addr are annotated as big-endian.
Code in ocfs2 had __force casts added apparently to shut the sparse
warnings up; of course, these days they only serve to *produce* warnings
for no reason whatsoever...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
BFS_FILEBLOCKS() expects struct bfs_inode * (on-disk data, with little-
endian fields), not struct bfs_inode_info * (in-core stuff, with host-
endian ones).
It's a macro and fields with the right names are present in
bfs_inode_info, so it compiles, but on big-endian host it gives bogus
results.
Introduced in commit f433dc5634 ("Fixes to
the BFS filesystem driver").
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that X86_32 is provided on Kconfig level for uml-i386, there's no
need to play with it explicitly on Makefile level anymore.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
access_flags_to_mode() gets on-the-wire data (little-endian) and treats
it as host-endian.
Introduced in commit e01b640013 ("[CIFS]
enable get mode from ACL when cifsacl mount option specified")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Given a specifically crafted binary do_brk() can be used to get low pages
available in userspace virtual memory and can thus be used to circumvent
the mmap_min_addr low memory protection. Add security checks in do_brk().
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: James Morris <jmorris@namei.org>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I can't pass memory allocated by kmalloc() to ksize() if it is allocated by
SLUB allocator and size is larger than (I guess) PAGE_SIZE / 2.
The error of ksize() seems to be that it does not check if the allocation
was made by SLUB or the page allocator.
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Christoph Lameter <clameter@sgi.com>, Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Before we start committing a transaction, we call
__journal_clean_checkpoint_list() to cleanup transaction's written-back
buffers.
If this call happens to remove all of them (and there were already some
buffers), __journal_remove_checkpoint() will decide to free the transaction
because it isn't (yet) a committing transaction and soon we fail some
assertion - the transaction really isn't ready to be freed :).
We change the check in __journal_remove_checkpoint() to free only a
transaction in T_FINISHED state. The locking there is subtle though (as
everywhere in JBD ;(). We use j_list_lock to protect the check and a
subsequent call to __journal_drop_transaction() and do the same in the end
of journal_commit_transaction() which is the only place where a transaction
can get to T_FINISHED state.
Probably I'm too paranoid here and such locking is not really necessary -
checkpoint lists are processed only from log_do_checkpoint() where a
transaction must be already committed to be processed or from
__journal_clean_checkpoint_list() where kjournald itself calls it and thus
transaction cannot change state either. Better be safe if something
changes in future...
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Writing to XIP files at a non-page-aligned offset results in data corruption
because the writes were always sent to the start of the page.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The AMD CS5535/CS5536 GPIO has two alternate output modes: AUX-1 and AUX-2.
When either AUX is enabled, the cs5535_gpio driver cannot control the
output.
Some BIOS code for the Geode processor enables AUX-1 for GPIO-1, which
configures it as the PC BEEP output.
This patch will disable AUX-1 and AUX-2 when the user enables output.
Signed-of-by: Ben Gardner <gardner.ben@gmail.com>
Cc: Richard Knutsson <ricknu-0@student.ltu.se>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
register_sysctl_table() can return NULL sometimes, e.g. when kmalloc()
returns NULL or when sysctl check fails.
I've also noticed, that many (most?) code in the kernel doesn't check for
the return value from register_sysctl_table() and later simply calls the
unregister_sysctl_table() with potentially NULL argument.
This is unlikely on a common kernel configuration, but in case we're
dealing with modules and/or fault-injection support, there's a slight
possibility of an OOPS.
Changing all the users to check for return code from the registering does
not look like a good solution - there are too many code doing this and
failure in sysctl tables registration is not a good reason to abort module
loading (in most of the cases).
So I think, that we can just have this check in unregister_sysctl_table
just to avoid accidental OOPS-es (actually, the unregister_sysctl_table()
did exactly this, before the start_unregistering() appeared).
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- reconfigure SPI baud from speed_hz of each spi transfer
- according to spi_transfer.bits_per_word to reprogram register and setup
correct SPI operation handlers
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove some sort of bloaty code, try to get these pin_req arrays built at compile-time
- move this static things to the blackfin board file
- add pin_req array to struct bfin5xx_spi_master
- tested on BF537/BF548 with SPI flash
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Set correct baud for spi mmc and enable SPI only after DMA is started.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix bug in u16_cs_chg_reader to read data_len-2 bytes data firstly, then read
out the last 2 bytes data
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move global SPI regs_base and dma_ch to struct driver_data. Test on BF54x SPI
Flash with 2 spi_master devices enabled.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move spin/waits to more correct locations in bfin SPI driver.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix SPI driver to work with SPI flash ST M25P16 on bf548
Currently the SPI driver enables the SPI controller and sets the SPI baud
register for each SPI transfer. But they should never be changed within a SPI
message session, in which several SPI transfers are pumped.
This patch moves SPI setting to the begining of a message session, and
never disables SPI controller until an error occurs.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use portmux mechanism to support SPI busses 1 and 2, instead of just the
original bus 0.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update spi driver to support multi-ports by using platform resources; tested
on STAMP537+SPI_MMC, other boards need more testing. Plus other minor
updates.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prevent people from setting bits in ctl_reg that the SPI framework already
handles, hopefully we can one day drop ctl_reg completely
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Respect per-transfer cs_change field (protocol tweaking support) by
adding and using cs_active/cs_deactive functions.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cleanup and error handling
- add error handling in SPI bus driver with selecting clients
- use proper defines to access Blackfin MMRs
- remove useless SSYNCs
- cleaner use of portmux calls
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use new Blackfin portmux interface, add error handling.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Initial BF54x SPI support
- support BF54x SPI0
- clean up some code (whitespace etc)
- will support multiports in the future
- start using portmux calls
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Given the patch which simplifies the spi_sync calling convention, this one
updates the callers of that routine which tried using it according to the
previous specification. (Most didn't.)
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simplify spi_sync calling convention, eliminating the need to check both
the return value AND the message->status. In consequence, this corrects
misbehaviours of spi_read and spi_write (which only checked the former) and
their callers.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add comment to at25 driver that it's for EEPROM chips, not FLASH
chips ... the AT25 series has both types of chip, and sometimes
they're even pin-compatible. The command sets are different, as
is the treatment of erasure. (FLASH needs explicit erasure, but
with EEPROM it's implicit.) Note that all vendors seem to have
this same confusion in their *25* series SPI memory parts.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make spi_write_then_read() use a mutex not a binary semaphore.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm/slub.c exports ksize(), but mm/slob.c and mm/slab.c don't.
It's used by binfmt_flat, which can be built as a module.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
this call should use the array index j, not i. But with this approach, just
one int i is enough, int j is not needed.
Signed-off-by: Denis Cheng <crquan@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes regression, introduced since 2.6.16. NextStep variant of
UFS as OpenStep uses directory block size equals to 1024. Without this
change, ufs_check_page fails in many cases.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Evgeniy Dushistov <dushistov@mail.ru>
Cc: Dave Bailey <dsbailey@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We must make sure that the RTC_DEV_BUSY flag has proper lock semantics,
i.e. that the RTC_DEV_BUSY stores clearing the flag don't get reordered
before the preceeding stores and loads and vice versa.
Spotted by Nick Piggin.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently we are complicating the code in copy_process, the clone ABI, and
if we fix the bugs sys_setsid itself, with an unnecessary open coded
version of sys_setsid.
So just simplify everything and don't special case the session and pgrp of
the initial process in a pid namespace.
Having this special case actually presents to user space the classic linux
startup conditions with session == pgrp == 0 for /sbin/init.
We already handle sending signals to processes in a child pid namespace.
We need to handle sending signals to processes in a parent pid namespace
for cases like SIGCHILD and SIGIO.
This makes nothing extra visible inside a pid namespace. So this extra
special case appears to have no redeeming merits.
Further removing this special case increases the flexibility of how we can
use pid namespaces, by not requiring the initial process in a pid namespace
to be a daemon.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On 2.6.24, top started showing 100% iowait on one CPU when a UML instance was
running (but completely idle). The UML code sits in io_getevents waiting for
an event to be submitted and completed.
Fix this by checking ctx->reqs_active before scheduling to determine whether
or not we are waiting for I/O.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Cc: Zach Brown <zach.brown@oracle.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
