Align the format for tx_statistics and rx_statistics debugfs output for
better readability
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In both 6x00 and 6x50 series, the enhanced/extended tx power table in
EEPROM is used to set the max. tx power limit.
This new tx power table is in 1/2 dBm format, which creates an issue of
possibility of 1/2 dBm loss when driver set the tx power limit; because
of driver keep track and report the tx power in dBm format.
In order to prevent the 1/2 dBm loss, keep track of the true max tx
power in 1/2 dBm format in driver; do the comparison and adjust the tx
power if needed when send tx power command to uCode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Power-saving logic will not re-issue a POWER_TABLE_CMD if a new command
matches the prior one. This can be bad if we re-start the device due to
e.g. uCode error; the new POWER_TABLE_CMD (required to invoke power-saving)
may match the prior POWER_TABLE_CMD issued before the uCode error.
Ensure the POWER_TABLE_CMD is sent to device when uCode is up.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When issue REPLY_STATISTICS_CMD to uCode, two possible flag
can be set in the configuration flags
bit 0: Clear statistics
0: Do not clear Statistics counters
1: Clear to zero Statistics counters
Allow "clear" parameter to be set from the caller.
Add debugfs file to clear the statistics counters to help monitor and
debug the uCode behavior.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Number of data structure for 6000 series no longer in production, the
data structure already being removed; also need to remove the external
reference define in iwl-dev.h
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drop the non-production PCI-IDs for 6x50 series
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Number of HT40 power parameters are not used; remove those from
iwl_channel_info data structure
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Temporary disable the coex function for wifi/wimax for 6x50
series until the full implementation ready.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Validate enhanced tx power entry read from EEPROM before applying the
tx power value. Different versions of EEPROM might contain different size
of table; always a good idea to make sure the entry is valid before
applying to the targeted channel.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In this file, function names are otherwise used as pointers without &.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f;
@@
f(...) { ... }
@@
identifier r.f;
@@
- &f
+ f
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
I may have botched my merge conflict resolution instructions for Dave...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add txq_id info to "Tx queue requesting wakeup" debug message
Add "Rx queue requesting wakeup" debug message
Move clear of CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ to be after nearby
iwl_write_prph(), since iwl_write_prph() sets it and clears it. Almost
removed it entirely, but just making sure in case someone removes the
iwl_write_prph()! Also remove unneeded priv->lock usage; this is now
handled by priv->reg_lock within iwl_clear_bit().
Join a couple of lines that had unneeded line returns.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Turn on RTS/CTS for HT to prevent uCode TX fifo underrun
This is fix for
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2103
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: Jiajia Zheng <jiajia.zheng@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Follow-up to "update write pointers for all tx queues after wakeup"; that
patch changed iwl_irq_tasklet_legacy(), but not iwl_irq_tasklet(), so
newer devices were not covered.
Comments from original patch:
Wakeup interrupt has been updating write pointers (indexes, actually) only
for tx queues 0-5. This is adequate just for 3945, but inadequate for other
devices, all of which have more tx queues. Now updating all tx/command queues,
so device can be aware of all new tx and host commands enqueued while
device was asleep.
This can potentially improve data traffic bandwidth and/or latency.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Take advantage of device's auto-increment for SRAM reads to eliminate extra
write address accesses.
Grab/release NIC access before/after entire read sequence, rather than for
each read individually.
After a quick check of dmesg logs, this seems to double Event Log dump speed,
reducing from about 20 milliseconds to about 10 milliseconds for 512 entries
using 3945.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If device provides bad values for Event Log parameters (due to being asleep
or SRAM corruption, etc.), the size can be very, very large (e.g. 0xa5a5a5a5),
which can flood system log.
Sanity-check capacity and next_entry values and limit to reasonable size dump.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not use AP's SM_PS setting for our own SM_PS setting.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the support for all the PCI_IDs never make into production
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Different channel has different configuration, need to pass correct
configuration to uCode when send "channel switch" command to uCode.
Invalid configuration will cause sysassert in uCode and produce
un-expected result.
Even it is a very small windows, but we also need to consider and handle
the case if commit_rxon occurred before the "channel switch
announcement" notification received from uCode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is part of the code, but the comment doesn't have it,
add pointers to the code and the FIFO usage for 5000 and
up.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove un-used parameter "recovery_rxon" from "priv" data structure
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I added that code setting the swq_id, I evidently
did not understand the distinction between FIFO and TX
queue yet and added code to compare a queue ID and a
FIFO number, which is bogus.
However, the code there need not be this specific, it
can just set all queues to the identity mapping which
will be overwritten by the aggregation queue code. As
a bit of defensive coding, don't assign an swq_id to
the command queue so that if we ever use it for frames
we notice quickly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The fourth queue (command queue) is already activated in
the loop above that also maps it to the command FIFO and
therefore doesn't need to be marked as activated again.
Also change the TODO comment to be accurate -- we need
to initialise the _queues_, not FIFOs, and map them to
device FIFOs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For both 6x00 and 6x50 series devices, periodic Tx IQ calibration is
disabled in uCode, driver do not need to set the periodic Tx/IQ calibration
bit in calibration command.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use configured valid rx chains in scan command instead of ANT_ABC, correcting
valid rx chain configuration of 4965, should be ANT_ABC instead of ANT_AB.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When doing scan in power saving mode, choose only 1 valid RX chain instead of
turning all chains on.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To help debug rx related issues, if IWL_DEBUG_RADIO flag is set, print
the rxon configuration when rxon host command send to uCode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allocate 128 bytes linear buffer for rx skb. The first 64 bytes is
reserved for mac80211 usage (for radiotap header expansion, etc).
The frame header starts from the second 64 bytes.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since these messages indicate failure we would be interested in seeing them
always.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we have a TODO item to make all station
management dependent on virtual interfaces, I
figured I'd start with pushing such a change
to drivers before more drivers start using the
ieee80211_find_sta() API with a hw pointer and
cause us grief later on.
For now continue exporting the old API in form
of ieee80211_find_sta_by_hw(), but discourage
its use strongly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For 6x50 series, it is wimax/wifi combo device, so driver need to enable
the wimax/wifi co-exist function and send the coexist event priority
table to uCode for operation.
The priority table will be used by uCode to determine what is the proper
action it should take when co-exist with WiMAX.
For example, when WiFi runs a scan, it must own radio exclusively, therefore
will disconnect WiMAX if WiMAX is connected.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Spatial Multiplexing Power Save was disabled to achieve better
throughput while in power save mode by activating all the rx chains all the time.
By doing so, the device power consumption is high.
Enable static/dynamic spatial multiplexing power save if device support
it, which can lower the power consumption without impact throughput.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add data structure define for COEX_MEDIUM_NOTIFICATION and
COEX_EVENT_CMD host commands.
COEX_MEDIUM_NOTIFICATION is notification from uCode to host to indicate
medium changes. COEX_EVENT_CMD is from host to uCode for coex event
request.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
More information than the "-EIO" return code will be useful here.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fits better in how the callbacks operate (alloc does allocation and
init does initialization). This also helps if we later want to do our own
initialization without relying on the mac80211 allocation.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the rate scale information is pointed to from the mac80211
station structure but since that is the only member we might as well make
it part of the structure. Also move the rate scaling initialization to the
init function, no need to do it when we allocate the structure. This fits
with how mac80211 deals with rate scaling information (it always calls init
after allocation) and makes it easier for us to later call initialization
directly.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In preparation for some station management changes we split the addition of
a broadcast station from the other stations. Later we will rely on mac80211
to direct all management (addition/removal) of all stations except the
broadcast station.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since iwlagn is the only user of these functions, move it to this module.
This results in a bit more code moving than just these functions since the
functions only used by them are also moved and we need to export the
symbols previously available to them directly.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handling responses to driver originated commands include passing the
original command buffer to the caller. At this time it is possible for a
callback to be invoked that is passed this command buffer and thus likely
to access it.
We need to make sure that the memory associated with that buffer is not DMA
mapped at the time.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wakeup interrupt has been updating write pointers (indexes, actually) only
for tx queues 0-5. This is adequate just for 3945, but inadequate for other
devices, all of which have more tx queues. Now updating all tx/command queues,
so device can be aware of all new tx and host commands enqueued while
device was asleep.
This can potentially improve data traffic bandwidth and/or latency.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add/clarify comments and debug messages for interrupt used only for uCode load
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Invoke workaround to avoid instability in L0->L0S->L1 transition on PCIe bus.
Workaround disables L0S state so device moves directly from L0->L1.
Workaround needed on all devices since and including 4965; add to 6000/1000.
Describe bug and workaround better in comments.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To save power, don't run apm_ops.init() until needed at "up" time.
EEPROM (5000 and earlier devices) may be read without running apm_ops.init(),
but OTP reads (6000 and newer devices) require a powered-up chip.
Therefore, remove apm_ops.init() from the general path in XXXX_pci_probe(),
and call it only if device uses OTP. Once done with OTP read, call
apm_ops.stop() to reset chip and save power until "up" time comes around.
NOTE: This patch depends on removal of priv->lock from iwl_apm_stop();
lock does not get initialized until later in flow. See patch
"remove unneeded locks from apm_stop()".
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since priv->reg_lock was added to keep multi-access register manipulation
atomic, priv->lock protection is no longer needed. Remove this from
iwl_apm_stop_master() and iwl_apm_stop().
Add warning of timeout when polling for busmaster disablement confirmation,
and some comments.
NOTE: This is needed to enable use of apm_ops.stop() within iwl_eeprom_init();
priv->lock does not get initialized until after this flow. See patch
"remove power-wasting calls to apm_ops.init()"
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By setting the firmware version in wiphy it is possible to obtain this
information via ethtool. Some examples,
# ethtool -i wlan1
driver: iwlagn
version: 2.6.32-rc5-wl-56840-g26d8540
firmware-version: 228.57.2.23
bus-info: 0000:03:00.0
# ethtool -i wlan0
driver: iwl3945
version: 2.6.32-rc5-wl-56840-g26d8540
firmware-version: 15.28.2.8
bus-info: 0000:02:00.0
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the WLAN_PRE80211 drivers moved to drivers/staging, this
distinction becomes unnecessary.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'COEX_PRIORITY_TABLE_CMD' host command will be supported for 5000 series
and up.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
