Made kernel accept IPv6 routes with IPv4-mapped address as next-hop.
It is possible to configure IP interfaces with IPv4-mapped addresses, and
one can add IPv6 routes for IPv4-mapped destinations/prefixes, yet prior
to this fix the kernel returned an EINVAL when attempting to add an IPv6
route with an IPv4-mapped address as a nexthop/gateway.
RFC 4798 (a proposed standard RFC) uses IPv4-mapped addresses as nexthops,
thus in order to support that type of address configuration the kernel
needs to allow IPv4-mapped addresses as nexthops.
Signed-off-by: Erik Nordmark <nordmark@arista.com>
Signed-off-by: Bob Gilligan <gilligan@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Occasionally, clang (e.g. version 3.8.1) translates a sum between two
constant operands using a BPF_OR instead of a BPF_ADD. The verifier is
currently not handling this scenario, and the destination register type
becomes UNKNOWN_VALUE even if it's still storing a constant. As a result,
the destination register cannot be used as argument to a helper function
expecting a ARG_CONST_STACK_*, limiting some use cases.
Modify the verifier to handle this case, and add a few tests to make sure
all combinations are supported, and stack boundaries are still verified
even with BPF_OR.
Signed-off-by: Gianluca Borello <g.borello@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ethtooll::nway_restart by utilizing mii_nway_restart.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2016-12-03
Here's a set of Bluetooth & 802.15.4 patches for net-next (i.e. 4.10
kernel):
- Fix for a potential NULL deref in the ieee802154 netlink code
- Fix for the ED values of the at86rf2xx driver
- Documentation updates to ieee802154
- Cleanups to u8 vs __u8 usage
- Timer API usage cleanups in HCI drivers
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
tcp: tsq: performance series
Under very high TX stress, CPU handling NIC TX completions can spend
considerable amount of cycles handling TSQ (TCP Small Queues) logic.
This patch series avoids some atomic operations, but most notable
patch is the 3rd one, allowing other cpus processing ACK packets and
calling tcp_write_xmit() to grab TCP_TSQ_DEFERRED so that
tcp_tasklet_func() can skip already processed sockets.
This avoid lots of lock acquisitions and cache lines accesses,
particularly under load.
In v2, I added :
- tcp_small_queue_check() change to allow 1st and 2nd packets
in write queue to be sent, even in the case TX completion of
already acknowledged packets did not happen yet.
This helps when TX completion coalescing parameters are set
even to insane values, and/or busy polling is used.
- A reorganization of struct sock fields to
lower false sharing and increase data locality.
- Then I moved tsq_flags from tcp_sock to struct sock also
to reduce cache line misses during TX completions.
I measured an overall throughput gain of 22 % for heavy TCP use
over a single TX queue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
tsq_flags being in the same cache line than sk_wmem_alloc
makes a lot of sense. Both fields are changed from tcp_wfree()
and more generally by various TSQ related functions.
Prior patch made room in struct sock and added sk_tsq_flags,
this patch deletes tsq_flags from struct tcp_sock.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Group fields used in TX path, and keep some cache lines mostly read
to permit sharing among cpus.
Gained two 4 bytes holes on 64bit arches.
Added a place holder for tcp tsq_flags, next to sk_wmem_alloc
to speed up tcp_wfree() in the following patch.
I have not added ____cacheline_aligned_in_smp, this might be done later.
I prefer doing this once inet and tcp/udp sockets reorg is also done.
Tested with both TCP and UDP.
UDP receiver performance under flood increased by ~20 % :
Accessing sk_filter/sk_wq/sk_napi_id no longer stalls because sk_drops
was moved away from a critical cache line, now mostly read and shared.
/* --- cacheline 4 boundary (256 bytes) --- */
unsigned int sk_napi_id; /* 0x100 0x4 */
int sk_rcvbuf; /* 0x104 0x4 */
struct sk_filter * sk_filter; /* 0x108 0x8 */
union {
struct socket_wq * sk_wq; /* 0x8 */
struct socket_wq * sk_wq_raw; /* 0x8 */
}; /* 0x110 0x8 */
struct xfrm_policy * sk_policy[2]; /* 0x118 0x10 */
struct dst_entry * sk_rx_dst; /* 0x128 0x8 */
struct dst_entry * sk_dst_cache; /* 0x130 0x8 */
atomic_t sk_omem_alloc; /* 0x138 0x4 */
int sk_sndbuf; /* 0x13c 0x4 */
/* --- cacheline 5 boundary (320 bytes) --- */
int sk_wmem_queued; /* 0x140 0x4 */
atomic_t sk_wmem_alloc; /* 0x144 0x4 */
long unsigned int sk_tsq_flags; /* 0x148 0x8 */
struct sk_buff * sk_send_head; /* 0x150 0x8 */
struct sk_buff_head sk_write_queue; /* 0x158 0x18 */
__s32 sk_peek_off; /* 0x170 0x4 */
int sk_write_pending; /* 0x174 0x4 */
long int sk_sndtimeo; /* 0x178 0x8 */
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a likely() in tcp_mtu_probe() moves its code which used to
be inlined in front of tcp_write_xmit()
We still have a cache line miss to access icsk->icsk_mtup.enabled,
we will probably have to reorganize fields to help data locality.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always allow the two first skbs in write queue to be sent,
regardless of sk_wmem_alloc/sk_pacing_rate values.
This helps a lot in situations where TX completions are delayed either
because of driver latencies or softirq latencies.
Test is done with no cache line misses.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under high load, tcp_wfree() has an atomic operation trying
to schedule a tasklet over and over.
We can schedule it only if our per cpu list was empty.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under high stress, I've seen tcp_tasklet_func() consuming
~700 usec, handling ~150 tcp sockets.
By setting TCP_TSQ_DEFERRED in tcp_wfree(), we give a chance
for other cpus/threads entering tcp_write_xmit() to grab it,
allowing tcp_tasklet_func() to skip sockets that already did
an xmit cycle.
In the future, we might give to ACK processing an increased
budget to reduce even more tcp_tasklet_func() amount of work.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of atomically clear TSQ_THROTTLED and atomically set TSQ_QUEUED
bits, use one cmpxchg() to perform a single locked operation.
Since the following patch will also set TCP_TSQ_DEFERRED here,
this cmpxchg() will make this addition free.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cleanup, to ease code review of following patches.
Old 'enum tsq_flags' is renamed, and a new enumeration is added
with the flags used in cmpxchg() operations as opposed to
single bit operations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: Add DCBNL support.
This series adds DCBNL operations to support host-based IEEE DCBX.
v2: Updated to the latest firmware interface spec.
David, please consider this series for net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Report PFC statistics to ethtool -S and DCBNL.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support only IEEE DCBX initially. Add IEEE DCBNL ops and functions to
get and set the hardware DCBX parameters. The DCB code is conditional on
Kconfig CONFIG_BNXT_DCB.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Latest interface has the latest DCB command structs. Get and store the
max number of lossless TCs the hardware can support.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new function bnxt_setup_mq_tc() to handle MQPRIO. This new function
will be called during ETS setup when we add DCBNL in the next patch.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the documentation, the PHYs supported by this driver
can also support pause frames. Announce this to be so.
Tested with a TI83822I.
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implemented RFC7527 Enhanced DAD.
IPv6 duplicate address detection can fail if there is some temporary
loopback of Ethernet frames. RFC7527 solves this by including a random
nonce in the NS messages used for DAD, and if an NS is received with the
same nonce it is assumed to be a looped back DAD probe and is ignored.
RFC7527 is enabled by default. Can be disabled by setting both of
conf/{all,interface}/enhanced_dad to zero.
Signed-off-by: Erik Nordmark <nordmark@arista.com>
Signed-off-by: Bob Gilligan <gilligan@arista.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn says:
====================
mv88e6390 batch 3
More patches to support the MV88e6390. This is mostly refactoring
existing code and adding implementations for the mv88e6390. This
patchset set which reserved frames are sent to the cpu, the size of
jumbo frames that will be accepted, turn off egress rate limiting, and
configuration of pause frames.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 has a number flow control registers accessed via the
Flow Control register. Use these to set the pause control.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 has a different mechanism for configuring pause.
Refactor the code into an ops function, and for the moment, don't add
any mv88e6390 code yet.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two different rate limiting configurations, depending on the
switch generation. Refactor this into ops.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switches support jumbo frames. Refactor this code into operations
in the ops structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older devices have a couple of registers in global2. The mv88e6390
family has a single register in global1 behind which hides similar
configuration. Implement and op for this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn says:
====================
MV88E6390 batch two
This is the second batch of patches adding support for the
MV88e6390. They are not sufficient to make it work properly.
The mv88e6390 has a much expanded set of priority maps. Refactor the
existing code, and implement basic support for the new device.
Similarly, the monitor control register has been reworked.
The mv88e6390 has something odd in its EDSA tagging implementation,
which means it is not possible to use it. So we need to use DSA
tagging. This is the first device with EDSA support where we need to
use DSA, and the code does not support this. So two patches refactor
the existing code. The two different register definitions are
separated out, and using DSA on an EDSA capable device is added.
v2:
Add port prefix
Add helper function for 6390
Add _IEEE_ into #defines
Split monitor_ctrl into a number of separate ops.
Remove 6390 code which is management, used in a later patch
s/EGREES/EGRESS/.
Broke up setup_port_dsa() and set_port_dsa() into a number of ops
v3:
Verify mandatory ops for port setup
Don't set ether type for DSA port.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Older chips only support DSA tagging. Newer chips have both DSA and
EDSA tagging. Refactor the code by adding port functions for setting the
frame mode, egress mode, and if to forward unknown frames.
This results in the helper mv88e6xxx_6065_family() becoming unused, so
remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v3:
Verify mandatory ops for port setup
Don't set ether type for DSA port.
Signed-off-by: David S. Miller <davem@davemloft.net>
Older chips support a single tagging protocol, DSA. New chips support
both DSA and EDSA, an enhanced version. Having both as an option
changes the register layouts. Up until now, it has been assumed that
if EDSA is supported, it will be used. Hence the register layout has
been determined by which protocol should be used. However, mv88e6390
has a different implementation of EDSA, which requires we need to use
the DSA tagging. Hence separate the selection of the protocol from the
register layout.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 changes the monitor control register into the Monitor
and Management control, which is an indirection register to various
registers.
Add ops to set the CPU port and the ingress/egress port for both
register layouts, to global1
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 does not have the two registers to set the frame
priority map. Instead it has an indirection registers for setting a
number of different priority maps. Refactor the old code into an
function, implement the mv88e6390 version, and use an op to call the
right one.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
ipv4: fib: Replay events when registering FIB notifier
Ido says:
In kernel 4.9 the switchdev-specific FIB offload mechanism was replaced
by a new FIB notification chain to which modules could register in order
to be notified about the addition and deletion of FIB entries. The
motivation for this change was that switchdev drivers need to be able to
reflect the entire FIB table and not only FIBs configured on top of the
port netdevs themselves. This is useful in case of in-band management.
The fundamental problem with this approach is that upon registration
listeners lose all the information previously sent in the chain and
thus have an incomplete view of the FIB tables, which can result in
packet loss. This patchset fixes that by dumping the FIB tables and
replaying notifications previously sent in the chain for the registered
notification block.
The entire dump process is done under RCU and thus the FIB notification
chain is converted to be atomic. The listeners are modified accordingly.
This is done in the first eight patches.
The ninth patch adds a change sequence counter to ensure the integrity
of the FIB dump. The last patch adds the dump itself to the FIB chain
registration function and modifies existing listeners to pass a callback
to be executed in case dump was inconsistent.
---
v3->v4:
- Register the notification block after the dump and protect it using
the change sequence counter (Hannes Frederic Sowa).
- Since we now integrate the dump into the registration function, drop
the sysctl to set maximum number of retries and instead set it to a
fixed number. Lets see if it's really a problem before adding something
we can never remove.
- For the same reason, dump FIB tables for all net namespaces.
- Add a comment regarding guarantees provided by mutex semantics.
v2->v3:
- Add sysctl to set the number of FIB dump retries (Hannes Frederic Sowa).
- Read the sequence counter under RTNL to ensure synchronization
between the dump process and other processes changing the routing
tables (Hannes Frederic Sowa).
- Pass a callback to the dump function to be executed prior to a retry.
- Limit the dump to a single net namespace.
v1->v2:
- Add a sequence counter to ensure the integrity of the FIB dump
(David S. Miller, Hannes Frederic Sowa).
- Protect notifications from re-ordering in listeners by using an
ordered workqueue (Hannes Frederic Sowa).
- Introduce fib_info_hold() (Jiri Pirko).
- Relieve rocker from the need to invoke the FIB dump by registering
to the FIB notification chain prior to ports creation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b90eb75494 ("fib: introduce FIB notification infrastructure")
introduced a new notification chain to notify listeners (f.e., switchdev
drivers) about addition and deletion of routes.
However, upon registration to the chain the FIB tables can already be
populated, which means potential listeners will have an incomplete view
of the tables.
Solve that by dumping the FIB tables and replaying the events to the
passed notification block. The dump itself is done using RCU in order
not to starve consumers that need RTNL to make progress.
The integrity of the dump is ensured by reading the FIB change sequence
counter before and after the dump under RTNL. This allows us to avoid
the problematic situation in which the dumping process sends a ENTRY_ADD
notification following ENTRY_DEL generated by another process holding
RTNL.
Callers of the registration function may pass a callback that is
executed in case the dump was inconsistent with current FIB tables.
The number of retries until a consistent dump is achieved is set to a
fixed number to prevent callers from looping for long periods of time.
In case current limit proves to be problematic in the future, it can be
easily converted to be configurable using a sysctl.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The next patch will enable listeners of the FIB notification chain to
request a dump of the FIB tables. However, since RTNL isn't taken during
the dump, it's possible for the FIB tables to change mid-dump, which
will result in inconsistency between the listener's table and the
kernel's.
Allow listeners to know about changes that occurred mid-dump, by adding
a change sequence counter to each net namespace. The counter is
incremented just before a notification is sent in the FIB chain.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order not to hold RTNL for long periods of time we're going to dump
the FIB tables using RCU.
Convert the FIB notification chain to be atomic, as we can't block in
RCU critical sections.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can miss FIB notifications sent between the time the ports were
created and the FIB notification block registered.
Instead of receiving these notifications only when they are replayed for
the FIB notification block during registration, just register the
notification block before the ports are created.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert rocker to offload FIBs in deferred work in a similar fashion to
mlxsw, which was converted in the previous commits.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in the previous commits, we need to process FIB entries
addition / deletion events in FIFO order or otherwise we can have a
mismatch between the kernel's FIB table and the device's.
Create an ordered workqueue for rocker to which these work items will be
submitted to.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FIB offload is currently done in process context with RTNL held, but
we're about to dump the FIB tables in RCU critical section, so we can no
longer sleep.
Instead, defer the operation to process context using deferred work. Make
sure fib info isn't freed while the work is queued by taking a reference
on it and releasing it after the operation is done.
Deferring the operation is valid because the upper layers always assume
the operation was successful. If it's not, then the driver-specific
abort mechanism is called and all routed traffic is directed to slow
path.
The work items are submitted to an ordered workqueue to prevent a
mismatch between the kernel's FIB table and the device's.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're going to start processing FIB entries addition / deletion events
in deferred work. These work items must be processed in the order they
were submitted or otherwise we can have differences between the kernel's
FIB table and the device's.
Solve this by creating an ordered workqueue to which these work items
will be submitted to. Note that we can't simply convert the current
workqueue to be ordered, as EMADs re-transmissions are also processed in
deferred work.
Later on, we can migrate other work items to this workqueue, such as FDB
notification processing and nexthop resolution, since they all take the
same lock anyway.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in the previous commit, modules are going to need to take a
reference on fib info and then drop it using fib_info_put().
Add the fib_info_hold() helper to make the code more readable and also
symmetric with fib_info_put().
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Suggested-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FIB notification chain is going to be converted to an atomic chain,
which means switchdev drivers will have to offload FIB entries in
deferred work, as hardware operations entail sleeping.
However, while the work is queued fib info might be freed, so a
reference must be taken. To release the reference (and potentially free
the fib info) fib_info_put() will be called, which in turn calls
free_fib_info().
Export free_fib_info() so that modules will be able to invoke
fib_info_put().
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 255cb30425 ("net/sched: act_mirred: Add new tc_action_ops get_dev()")
Cc: Hadar Hen Zion <hadarh@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-12-02
This series contains updates to i40e and i40evf only.
Alex provides changes so that we are much more robust about defining what
we can and cannot offload in i40e and i40evf by doing additional checks
other than L4 tunnel header length.
Jake provides several fixes/changes, first cleaning up a label that is
unnecessary, as well as cleaned up the use of a "magic number". Clarified
the code by separating the global private flags and the regular private
flags per interface into two arrays, so that future additions will not
produce duplication and buggy code. Adds additional checks to protect
against NULL values for msix_entries and q_vectors pointers.
Michal adds Clause22 method for accessing registers for some external
PHYs.
Piotr adds additional protocol support for the admin queue discover
capabilities function.
Tushar Dave fixes a panic seen on SPARC, where writel() should not be
used to write directly to a memory address but only to a memory mapped
I/O address otherwise it causes data access exceptions.
Joe Perches separates out a section of code into its own function, to
help reduce i40evf_reset_task() a bit.
Alan fixes an issue by checking for NULL before dereferencing msix_entries
and returning early in the case where it is NULL within the i40evf_close()
code path.
Henry provides code cleanup to remove unreachable and redundant sections
of code. Fixed up an issue where new NICs were not identifying "unknown
PHYs" correctly.
Harshitha fixes a issue where the ethtool "Supported Link" modes list
backplane interfaces on X722 devices for 10 GbE with SFP+ and Cortina
retimer, where these interfaces should not be visible to the user since
they cannot use them.
Carolyn changes an X722 informational message so that it only appears
when extra messages are desired.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit of SOF_TIMESTAMPING_OPT_STATS didn't include the
new header for avr32, causing build to break. The patch fixes it.
Fixes: 1c885808e4 ("tcp: SOF_TIMESTAMPING_OPT_STATS option for SO_TIMESTAMPING")
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before commit 850cbaddb5 ("udp: use it's own memory accounting
schema"), the udp protocol allowed sk_rmem_alloc to grow beyond
the rcvbuf by the whole current packet's truesize. After said commit
we allow sk_rmem_alloc to exceed the rcvbuf only if the receive queue
is empty. As reported by Jesper this cause a performance regression
for some (small) values of rcvbuf.
This commit is intended to fix the regression restoring the old
handling of the rcvbuf limit.
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Fixes: 850cbaddb5 ("udp: use it's own memory accounting schema")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under heavy stress, timer used in estimators tend to slowly be delayed
by a few jiffies, leading to inaccuracies.
Lets remember what was the last scheduled jiffies so that we get more
precise estimations, without having to add a multiply/divide in the loop
to account for the drifts.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Logically, EFX_BUG_ON_PARANOID can never be correct. For, BUG_ON should
only be used if it is not possible to continue without potential harm;
and since the non-DEBUG driver will continue regardless (as the BUG_ON is
compiled out), clearly the BUG_ON cannot be needed in the DEBUG driver.
So, replace every EFX_BUG_ON_PARANOID with either an EFX_WARN_ON_PARANOID
or the newly defined EFX_WARN_ON_ONCE_PARANOID.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sargun Dhillon says:
====================
samples, bpf: Refactor; Add automated tests for cgroups
These two patches are around refactoring out some old, reusable code from the
existing test_current_task_under_cgroup_user test, and adding a new, automated
test.
There is some generic cgroupsv2 setup & cleanup code, given that most
environment still don't have it setup by default. With this code, we're able
to pretty easily add an automated test for future cgroupsv2 functionality.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the sample program test_cgrp2_attach2. This program is
similar to test_cgrp2_attach, but it performs automated testing of the
cgroupv2 BPF attached filters. It runs the following checks:
* Simple filter attachment
* Application of filters to child cgroups
* Overriding filters on child cgroups
* Checking that this still works when the parent filter is removed
The filters that are used here are simply allow all / deny all filters, so
it isn't checking the actual functionality of the filters, but rather
the behaviour around detachment / attachment. If net_cls is enabled,
this test will fail.
Signed-off-by: Sargun Dhillon <sargun@sargun.me>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
