New memory control config reg at 0x50 should be used for stolen
memory size detection on Sandybridge.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
* anholt/drm-intel-next:
drm/i915: Record batch buffer following GPU error
drm/i915: give up on 8xx lid status
drm/i915: reduce some of the duplication of tiling checking
drm/i915: blow away userspace mappings before fence change
drm/i915: move a gtt flush to the correct place
agp/intel: official names for Pineview and Ironlake
drm/i915: overlay: drop superflous gpu flushes
drm/i915: overlay: nuke readback to flush wc caches
drm/i915: provide self-refresh status in debugfs
drm/i915: provide FBC status in debugfs
drm/i915: fix drps disable so unload & re-load works
drm/i915: Fix OGLC performance regression on 945
drm/i915: Deobfuscate the render p-state obfuscation
drm/i915: add dynamic performance control support for Ironlake
drm/i915: enable memory self refresh on 9xx
drm/i915: Don't reserve compatibility fence regs in KMS mode.
drm/i915: Keep MCHBAR always enabled
drm/i915: Replace open-coded eviction in i915_gem_idle()
- Without this change I get a general protection fault.
- Also use PTR_ERR where applicable.
Signed-off-by: Maarten Maathuis <madman2003@gmail.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Acked-by: Thomas Hellstrom <thellstrom@vmware.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The whole attribute table is valid for
shr/shl ops.
Fixes fdo bug 26668
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
- add support for pre-avivo chips
- add support for fixed post/ref dividers
- add support for non-fractional fb dividers
By default avivo chips use the new algo and
pre-avivo chips use the old algo. Use the "new_pll"
module option to toggle between them.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch properly set visible VRAM and enforce any pinned buffer
to be into visible VRAM. We might later add a flag to release this
constraint for some newer hw more clever than previous.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: bug fix for vlan + gro issue
tc35815: Remove a wrong netif_wake_queue() call which triggers BUG_ON
cdc_ether: new PID for Ericsson C3607w to the whitelist (resubmit)
IPv6: better document max_addresses parameter
MAINTAINERS: update mv643xx_eth maintenance status
e1000: Fix DMA mapping error handling on RX
iwlwifi: sanity check before counting number of tfds can be free
iwlwifi: error checking for number of tfds in queue
iwlwifi: set HT flags after channel in rxon
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: Be in TS_POLLING state during mwait based C-state entry
ACPI: Fix regression where _PPC is not read at boot even when ignore_ppc=0
acer-wmi: Respect current backlight level when loading
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/vmwgfx: Fix queries if no dma buffer thrashing is occuring.
drm/nv50: fix vram ptes on IGPs to point at stolen system memory
drm/nv50: fix instmem binding on IGPs to point at stolen system memory
drm/nv50: improve vram page table construction
drm/nv50: more efficient clearing of gpu page table entries
drm/nv50: make nv50_mem_vm_{bind,unbind} operate only on vram
drm/nouveau: Fix up pre-nv17 analog load detection.
The netif_wake_queue() is called correctly (i.e. only on !txfull
condition) from txdone routine. So Unconditional call to the
netif_wake_queue() here is wrong. This might cause calling of
start_xmit routine on txfull state and trigger BUG_ON.
This bug does not happen when NAPI disabled. After txdone there
must be at least one free tx slot. But with NAPI, this is not
true anymore and the BUG_ON can hits on heavy load.
In this driver NAPI was enabled on 2.6.33-rc1 so this is
regression from 2.6.32 kernel.
Reported-by: Ralf Roesch <ralf.roesch@rw-gmbh.de>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new vid/pid to the cdc_ether whitelist.
Device added:
- Ericsson Mobile Broadband variant C3607w
Signed-off-by: Torgny Johansson <torgny.johansson@gmail.com>
--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for error return from pci_map_single/pci_map_page and clean up.
With this and the previous patch the driver was able to handle a significant
percentage of errors (I set the fault injection rate to 10% and could still
download large files at a reasonable speed).
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intercept query commands and apply relocations to their guest pointers.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'nouveau/for-airlied' of ../drm-nouveau-next:
drm/nv50: fix vram ptes on IGPs to point at stolen system memory
drm/nv50: fix instmem binding on IGPs to point at stolen system memory
drm/nv50: improve vram page table construction
drm/nv50: more efficient clearing of gpu page table entries
drm/nv50: make nv50_mem_vm_{bind,unbind} operate only on vram
drm/nouveau: Fix up pre-nv17 analog load detection.
Commit 4410f39109 ("fbdev: add support for
handoff from firmware to hw framebuffers") didn't add fb_destroy
operation to efifb. Fix it and change aperture_size to match size
passed to request_mem_region.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=15151
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Reported-by: Alex Zhavnerchik <alex.vizor@gmail.com>
Tested-by: Alex Zhavnerchik <alex.vizor@gmail.com>
Acked-by: Peter Jones <pjones@redhat.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
geode-mfgpt: restore previous behavior for selecting IRQ
The MFGPT IRQ used to be, in order of decreasing priority,
* IRQ supplied by the user as a boot-time parameter,
* IRQ previously set by the BIOS or another driver,
* default IRQ given at compile time.
Return to this behavior, which got broken when splitting the
MFGPT/clocksource driver for 2.6.33-rc1.
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Acked-by: Andres Salomon <dilinger@collabora.co.uk>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This also modifies the unused PRAMIN PT entries to be all zeroes, can't
really recall why I used 9/0 initially, just that it didn't work for
some reason. It was likely masking a bug elsewhere that's since been
fixed.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This commit changes nouveau to construct PTEs which look very much like
the ones the binary driver creates.
I presume that filling multiple PTEs identically with length flags and
the physical address of the start of a block of VRAM is a hint to the
memory controller that it need not perform additional page table lookups
for that range of addresses.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
AtomBIOS tables on non-mobility GPU do not contain POWERSAVE/BATTERY.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We kept pointers to requested and current clock modes in every power state.
That was useless, more /global/ pointers in power struct are enough.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- updated swizzle modes for backend map setup
- fix programming of a few gfx regs
- properly handle pipe/backend setup on LE cards
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch fixes occlusion queries and rendering errors
on rv740 boards. Hardcoding the backend map is not an optimal
solution, but a better fix is being worked on.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Version 2 of memory controller did break the initialization for
R3XX/R4XX hardware. This patch fix it.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch adds a check on avivo chips to see if we are in the VBL
region for the active crtcs when we trigger the engine change.
I appear to have glitches locally on pm transistion (not sure all
fixes are in yet) and this at least seems to be correct here,
maybe others can test on systems with no glitches.
Allocation of single large block of memory may fail under memory
presure. drm_buffer object can hold one large block of data in
multiple independ pages which preents alloation failures.
This patch converts all access to command stream to use drm_buffer
interface. All direct access to array has to go tough drm_buffer
functions to get correct pointer.
Outputting the command stream to ring buffer needs to be awear of
the split nature of drm_buffer. The output operation requires the
new OUT_RING_DRM_BUFFER.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Allocating multiple pages of memory for data that is coming
from user space may fail. To fix memory allocation failures
the buffer object should be split to multiple independ pages.
drm buffer provides generic interface to copy and process
large data arrays from user space.
Interface includes allocation and free functions to allocate
the buffer object and data storage pages.
All access operations are performed relative to a internal
pointer which is advanced with drm_buffer_advance function.
The buffer can be accessed using drm_buffer_pointer_to_XXX
functions if it is known that requested object doesn't split
over a page boundary. These functions don't do any error
checking to maximize performance.
If there is large object which could be split there is special
drm_buffer_read_object function. drm_buffer_read_object takes
a pointer as argument which is used as temporary store for
data if it is split over boundary in the buffer.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
ACPI deep C-state entry had a long standing bug/missing feature, wherein we were sending
resched IPIs when an idle CPU is in mwait based deep C-state. Only mwait based C1 was using
the write to the monitored address to wake up mwait'ing CPU.
This patch changes the code to retain TS_POLLING bit if we are entering an mwait based
deep C-state.
The patch has been verified to reduce the number of resched IPIs in general and also
improves the performance/power on workloads with low system utilization (i.e., when mwait based
deep C-states are being used).
Fixes "netperf ~50% regression with 2.6.33-rc1, bisect to 1b9508f"
http://marc.info/?l=linux-kernel&m=126441481427331&w=4
Reported-by: Lin Ming <ming.m.lin@intel.com>
Tested-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
In order to improve our diagnostic capabilities following a GPU hang
and subsequent reset, we need to record the batch buffer that triggered
the error. We assume that the current batch buffer, plus a few details
about what else is on the active list, will be sufficient -- at the very
least an improvement over nothing.
The extra information is stored in /debug/dri/.../i915_error_state
following an error, and may be decoded using
intel_gpu_tools/tools/intel_error_decode.
v2: Avoid excessive work under spinlocks.
v3: Include ringbuffer for later analysis.
v4: Use kunmap correctly and record more buffer state.
v5: Search ringbuffer for current batch buffer
v6: Use a work fn for the impossible IRQ error case.
v7: Avoid non-atomic paths whilst in IRQ context.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
These old machines more often than not lie about their lid state. So
don't use it to detect LVDS presence, but leave the event handler to
deal with lid open/close, when we might need to reset the mode.
Fixes kernel bug #15248
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
i915_gem_object_fenceable was mostly just a repeat of the
i915_gem_object_fence_offset_ok, but also checking the size (which was
checkecd when we allowed that BO to be tiled in the first place). So
instead, export the latter function and use it in place.
Signed-Off-By: Owain G. Ainsworth <oga@openbsd.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
