Driver has following initialization sequence for Target mode
1. Driver initialization starts
2. ISP Abort is scheduled when the target is enabled.
qla2xxx [0000:04:00.0]-4807:25: ISP abort scheduled
qla2xxx [0000:04:00.0]-00af:25: Performing ISP error recovery - ha=ffff880caa9e0000.
3. DPC thread starts the ISP Abort
4. While DPC is resetting the chip and initializing the firmware, we get
async events from the firmware about P2P mode, LOOP UP and PORT UPDATE.
5. PRLI from a initiator is delivered to us followed by a PLOGI and then a
SCSI command which creates a session.
6. If the SCSI command is a WRITE in this case, we issue XFR RDY and it
gets dropped as can be seen with messages RESET-XFR because ISP Abort
is still active
qla2xxx [0000:04:00.0]-e902:25: RESET-XFR active/old-count/new-count = 1/1/1.
7. If the SCSI command is a READ, we issue RESPONSE and they get dropped
as well because Abort is still active.
qla2xxx [0000:04:00.0]-e901:25: RESET-RSP active/old-count/new-count = 1/1/1
8. Now eventually, ISP Abort finishes clearing the DPC flags.
qla2xxx [0000:04:00.0]-8822:25: qla2x00_abort_isp succeeded.
qla2xxx [0000:04:00.0]-4808:25: ISP abort end.
9. Since we dropped SCSI commands silently (without any responses sent
to the initiator) initiator waits for a SCSI timeout (which is 60
seconds in our case), Sends an ABTS which fails since there
no se_cmd found for the tag that ABTS is referencing as the
commands were cleaned up in Step 6 and 7.
10. Initiator send an IO after the ABTS which succeed fine.
To fix the above case, the following changes have been made:
- To prevent target from dropping commands silently, use the online flag
instead to check for an active chip reset. Once the port is online during
a chip reset phase, we are good to process the commands.
- Clean up qla2x00_restart_isp to not set the online flag and process ATIO
as it is unnecessary. During a chip reset, interrupts are enabled only
after setting the online flag to 1, so ATIO's won't be missed and hence
no need to process ATIO's after setting the online flag.
Signed-off-by: Dilip Kumar Uppugandla <dilip@purestorage.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
set ATIO/Request/Response Queues and Default number
of outstanding command to 4k.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
99% of the time the ATIOQ has SCSI command. The other 1% of time
is something else. Most of the time this interrupt does not need
to hold the hardware_lock. We're moving the ATIO interrupt thread
to a different lock to reduce lock contention.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
queue work element to specific process lessen cache miss
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Sessions management (add, deleted, modify) currently are serialized
through the hardware_lock. Hardware_lock is a high traffic lock.
This lock is accessed by both the transmit & receive sides.
Sessions management is now moved off to another lock call sess_lock.
This is done to reduce lock contention and increase traffic throughput.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Replace QLA_TGT_STATE_ABORTED state with a bit because
the current state of the command is lost when an abort
is requested by upper layer.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Until now ack'ing of a new PLOGI has only been delayed if there
was an existing session for the same WWN. Ack was released when
the session deletion completed.
If there was another WWN session with the same fc_id/loop_id pair
(aka "conflicting session"), PLOGI was still ack'ed immediately.
This potentially caused a problem when old session deletion logged
fc_id/loop_id out of FW after new session has been established.
Two work-arounds were attempted before:
1. Dropping PLOGIs until conflicting session goes away.
2. Detecting initiator being logged out of FW and issuing LOGO
to force re-login.
This patch introduces proper solution to the problem where PLOGI
is held until either existing session with same WWN or any
conflicting session goes away. Mechanism supports one session holding
two PLOGI acks as well as one PLOGI ack being held by many sessions.
Signed-off-by: Alexei Potashnik <alexei@purestorage.com>
Acked-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
1. Initiator A is logged in with fc_id(1)/loop_id(1)
2. Initiator A re-logs in with fc_id(2)/loop_id(2)
3. Part of old session deletion async logoout for 1/1 is queued
4. Initiator B logs in with fc_id(1)/loop_id(1), starts
passing data and creates session.
5. Async logo from 3 is processed by DPC and sent to FW
Now initiator B has the session but is logged out from FW.
This condition is detected first with CTIO error 29 at which
point we should delete current session. During session
deletion we will send LOGO to initiator to force re-login.
Under rare circumstances initiator might be logged out of FW,
not have driver session, but still think it's logged in.
E.g. the above sequence plus session deletion due to re-config.
Incoming commands will fail to create local session because
initiator is not found in FW. In this case we also issue LOGO
to initiator to force him re-login.
Finally this patch fixes exchange leak when commands where
received in logged out state. In this case loop_id must be
set to FFFF when corresponding exchange is terminated. The
patch modifies exchange termination to always use FFFF,
since in certain scenarios it's impossible to tell whether
command was received in logged in or logged out state.
Signed-off-by: Alexei Potashnik <alexei@purestorage.com>
Acked-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds interface to send explicit LOGO
explicit LOGO using using ELS commands from driver.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
DebugFS now will show fw_resource_count node.
FW Resource count
Original TGT exchg count[0]
current TGT exchg count[0]
original Initiator Exchange count[2048]
Current Initiator Exchange count[2048]
Original IOCB count[2078]
Current IOCB count[2067]
MAX VP count[254]
MAX FCF count[0]
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Following counters are added in target mode to help debugging efforts.
Target Counters
qla_core_sbt_cmd = 0
qla_core_ret_sta_ctio = 0
qla_core_ret_ctio = 0
core_qla_que_buf = 0
core_qla_snd_status = 0
core_qla_free_cmd = 0
num alloc iocb failed = 0
num term exchange sent = 0
num Q full sent = 0
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch enables Exchange offload support in Qlogic ISP.
To enable exchange offload with Qlogic ISP24XX/25XX/26XX,
set module parameter ql2xexchoffld to any non-zero number.
This will alow ISP firmware to store exchange data structures
used by firmware to host memory provided by driver. ISP firmware
can supports upto 32k total active exchanges.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch enables Extended Logins support in Qlogic ISP.
To enable extended login with Qlogic ISP24XX/25XX/26XX,
set module parameter ql2xexlogins to any non-zero number.
This will alow ISP firmware to store port database structure
information of remote login sessions to host memory provided
by driver. ISP firmware supports upto 16k total logins.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
HP C2502 cards (based on 53C400A chips) use different magic numbers for
software-based I/O address configuration than other cards.
The configuration is also extended to allow setting the IRQ.
Move the configuration to a new function magic_configure() and move
magic the magic numbers into an array. Add new magic numbers for these
HP cards and hp_c2502 module parameter to use them, e.g.:
modprobe g_NCR5380 ncr_irq=7 ncr_addr=0x280 hp_c2502=1
Tested with HP C2502 and DTCT-436P.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The check for 53C80 registers accessibility was commented out because
it was broken (inverted). Fix and enable it.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add I/O register mapping for DTC chips and enable PDMA mode.
These chips have 16-bit wide HOST BUFFER register and it must be read
by 16-bit accesses (we lose data otherwise).
Large PIO transfers crash at least the DTCT-436P chip (all reads result
in 0xFF) so this patch actually makes it work.
The chip also crashes when we bang on the C400 host status register too
heavily after PDMA write - a small udelay is needed.
Tested on DTCT-436P and verified that it does not break 53C400A.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add I/O register mapping for NCR53C400A and enable PDMA mode to
improve performance and fix non-working IRQ.
Tested with HP C2502 (and user-space enabler).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Convert compile-time C400_ register mapping to runtime mapping.
This removes the weird negative register offsets and allows adding
additional mappings.
While at it, convert read/write loops into insb/outsb.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pseudo-DMA (PDMA) has been broken for ages, resulting in hangs on
53C400-based cards.
According to 53C400 datasheet, PDMA transfer length must be a multiple
of 128. Check if that's true and use PIO if it's not.
This makes PDMA work on 53C400 (Canon FG2-5202).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the past, atari_NCR5380.c was overlooked by those working on NCR5380.c
and this caused needless divergence. All of the changes in this patch were
taken from NCR5380.c.
This removes some unimportant discrepancies between the two core driver
forks so that 'diff' can be used to reveal the important ones, to
facilitate reunification.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the past, NCR5380.c was overlooked by those working on atari_NCR5380.c
and this caused needless divergence. All of the changes in this patch were
taken from atari_NCR5380.c.
This removes some unimportant discrepancies between the two core driver
forks so that 'diff' can be used to reveal the important ones, to
facilitate reunification.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hanging indentation was a poor choice for the text inside comments. It
has been used in the wrong places and done badly elsewhere. There is
little consistency within any file. One fork of the core driver uses
tabs for this indentation while the other uses spaces. Better to use
flush-left alignment throughout.
This patch is the result of the following substitution. It replaces tabs
and spaces at the start of a comment line with a single space.
perl -i -pe 's,^(\t*[/ ]\*)[ \t]+,$1 ,' drivers/scsi/{atari_,}NCR5380.c
This removes some unimportant discrepancies between the two core driver
forks so that the important ones become obvious, to facilitate
reunification.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch is the result of the following substitution. It removes any
tabs and spaces at the end of a line.
perl -i -pe 's,[\t ]+$,,' drivers/scsi/{atari_,}NCR5380.c
This removes some unimportant discrepancies between the two core driver
forks so that the important ones become obvious, to facilitate
reunification.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The CVS revision log is not nearly as useful as the history/history.git
repo, so remove it. Roman's commentary at the top of his driver repeats
the same information elsewhere in the file so remove it. Also remove
some other redundant or obsolete comments.
Both the driver and the datasheets confusingly refer to a DMA access
for a SCSI WRITE command as a "DMA write". Similarly a SCSI READ command
is called a "DMA read". This is the opposite of the usual convention.
Thankfully, the chip documentation and driver code also use "DMA send" and
"DMA receive", so adopt this terminology.
This removes some unimportant discrepancies between the two core driver
forks so that 'diff' can be used to reveal the important ones, to
facilitate reunification.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Because of the rudimentary design of the chip, it is necessary to poll the
SCSI bus signals during PIO and this tends to hog the CPU. The driver will
accept new commands while others execute, and this causes a soft lockup
because the workqueue item will not terminate until the issue queue is
emptied.
When exercising dmx3191d using sequential IO from dd, the driver is sent
512 KiB WRITE commands and 128 KiB READs. For a PIO transfer, the rate is
is only about 300 KiB/s, so these are long-running commands. And although
PDMA may run at several MiB/s, interrupts are disabled for the duration
of the transfer.
Fix the unresponsiveness and soft lockup issues by calling cond_resched()
after each command is completed and by limiting max_sectors for drivers
that don't implement real DMA.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This refactoring removes two global Scsi_Host pointers. This
improves consistency with other ncr5380 drivers. Adopting the same
conventions as the other drivers makes them easier to read.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Keep the two core driver forks in sync.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove the HOSTNO macro that is peculiar to atari_NCR5380.c and
contributes to the problem of divergence of the NCR5380 core drivers.
Keep NCR5380.c in sync.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NCR5380.c lacks a sane eh_bus_reset_handler. The atari_NCR5380.c code is
much better but it should not throw out the issue queue (that would be
a host reset) and it neglects to set the result code for commands that it
throws out. Fix these bugs and keep the two core drivers in sync.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During arbitration and selection, the relevant command is invisible to
exception handlers and can be found only in a pointer on the stack of a
different thread.
When eh_abort_handler can't find a given command, it can't decide whether
that command was completed already or is still in arbitration or selection
phase. But it must return either SUCCESS (e.g. command completed earlier)
or FAILED (could not abort the nexus, try bus reset).
The solution is to make sure all commands belonging to the LLD are always
visible to exception handlers. Add another scsi_cmnd pointer to the
hostdata struct to track the command in arbitration or selection phase.
Replace 'retain_dma_irq' with the new 'selecting' pointer, to bring
atari_NCR5380.c into line with NCR5380.c.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce a new eh_abort_handler implementation. This one attempts to
follow all of the rules relating to EH handlers. There is still a known
bug: during selection, a command becomes invisible to the EH handlers
because it only appears in a pointer on the stack of a different thread.
This bug is addressed in a subsequent patch.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NCR5380_information_transfer() may re-queue a command for autosense,
after calling scsi_eh_prep_cmnd(). This creates several possibilities:
1. Reselection may intervene before the re-queued command gets processed.
If the reconnected command then undergoes autosense, this causes the
scsi_eh_save data from the previous command to be overwritten.
2. After NCR5380_information_transfer() calls scsi_eh_prep_cmnd(),
a new REQUEST SENSE command may arrive. This would be queued ahead
of any command already undergoing autosense, which means the
scsi_eh_save data might be restored to the wrong command.
3. After NCR5380_information_transfer() calls scsi_eh_prep_cmnd(),
eh_abort_handler() may abort the command. But the scsi_eh_save data is
not discarded, which means the scsi_eh_save data might be incorrectly
restored to the next REQUEST SENSE command issued.
This patch adds a new autosense list so that commands that are re-queued
because of a CHECK CONDITION result can be kept apart from the REQUEST
SENSE commands that arrive via queuecommand.
This patch also adds a function dedicated to dequeueing and preparing the
next command for processing. By refactoring the main loop in this way,
scsi_eh_save takes place when an autosense command is dequeued rather
than when re-queued.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Implement a 'complete_cmd' function to complete commands. This is needed
by the following patch; the new function provides a site for the logic
needed to correctly handle REQUEST SENSE commands.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The NCR5380 drivers have a home-spun linked list implementation for
scsi_cmnd structs that uses cmd->host_scribble as a 'next' pointer. Adopt
the standard list_head data structure and list operations instead. Remove
the eh_abort_handler rather than convert it. Doing the conversion would
only be churn because the existing EH handlers don't work and get replaced
in a subsequent patch.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The hostdata struct is now protected by a spin lock so the volatile
qualifiers are redundant. Remove them.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Printing command pointers can be useful when debugging queues. Other than
that, the LIST and REMOVE macros are just clutter. These macros are
redundant now that NDEBUG_QUEUES causes pointers to be printed, so remove
them.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Print the command pointers in the log messages for debugging queue data
structures. The LIST and REMOVE macros can then be removed.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make use of the shost_priv() helper. Remove HOSTDATA and SETUP_HOSTDATA
macros because they harm readability.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace all H_NO and some HOSTNO macros (both peculiar to atari_NCR5380.c)
with a new dsprintk macro that's more useful and more consistent. The new
macro avoids a lot of boilerplate in new code in subsequent patches. Keep
NCR5380.c in sync. Remaining HOSTNO macros are removed as side-effects
of subsequent patches.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some NCR5380 hosts offer a .show_info method to access the contents of
the various command list data structures from a procfs file. When NDEBUG
is set, the same information is sent to the console during EH.
The two core drivers, atari_NCR5380.c and NCR5380.c differ here. Because
it is just for debugging, the easiest way to fix the discrepancy is
simply remove this code.
The only remaining users of NCR5380_show_info() and NCR5380_write_info()
are drivers that define PSEUDO_DMA. The others have no use for the
.show_info method, so don't initialize it.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NCR5380.c presently uses the instance->host_lock spin lock. Convert this
to a new spin lock that protects the NCR5380_hostdata struct.
atari_NCR5380.c previously used local_irq_save/restore() rather than a
spin lock. Convert this to hostdata->lock in irq mode. For SMP platforms,
the interrupt handler now also acquires the spin lock.
This brings all locking in the two core drivers into agreement.
Adding this locking also means that a bunch of volatile qualifiers can be
removed from the members of the NCR5380_hostdata struct. This is done in
a subsequent patch.
Proper locking will allow the abort handler to locate a command being
aborted. This is presently impossible if the abort handler is invoked when
the command has been moved from a queue to a pointer on the stack. (If
eh_abort_handler can't determine whether a command has been completed
or is still being processed then it can't decide whether to return
success or failure.)
The hostdata spin lock is now held when calling NCR5380_select() and
NCR5380_information_transfer(). Where possible, the lock is dropped for
polling and PIO transfers.
Clean up the now-redundant SELECT_ENABLE_REG writes, that used to provide
limited mutual exclusion between information_transfer() and reselect().
Accessing hostdata->connected without data races means taking the lock;
cleanup these accesses.
The new spin lock falls away for m68k and other UP builds, so this should
have little impact there. In the SMP case the new lock should be
uncontested even when the SCSI bus is contested.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove FLAG_DTC3181E. It was used to suppress a final Arbitration Lost
(SEL asserted) test that isn't actually needed. The test was suppressed
because it causes problems for DTC436 and DTC536 chips. It takes place
after the host wins arbitration, so SEL has been asserted. These chips
can't seem to tell whether it was the host or another bus device that
did so.
This questionable final test appears in a flow chart in an early NCR5380
datasheet. It was removed from later documents like the DP5380 datasheet.
By the time this final test takes place, the driver has already tested
the Arbitration Lost bit several times. The first test happens 3 us after
BUS FREE (or longer due to register access delays). The protocol requires
that a device stop signalling within 1.8 us after BUS FREE unless it won
arbitration, in which case it must assert SEL, which is detected 1.2 us
later by the first Arbitration Lost test.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a target reports a QUEUE_FULL condition it causes the driver to
update the 'queue_size' limit with the number of currently allocated tags.
At least, that's what's supposed to happen, according to the comments.
Unfortunately the terms in the assignment are swapped. Fix this and
cleanup some obsolete comments.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add missing .module initializer. Use distinct .proc_name values for the
g_NCR5380 and g_NCR5380_mmio modules. Remove pointless CAN_QUEUE and
CMD_PER_LUN override macros. Cleanup whitespace and code style.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NDEBUG_NO_DATAOUT should not disable DATA IN phases too. Fix this.
(This bug has long been fixed in atari_NCR5380.c.)
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove unused includes (stat.h, signal.h, proc_fs.h) and move includes
needed by the core drivers into the common header (delay.h etc).
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the array bounds check when transferring an extended message from the
target.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bring the two NCR5380_reselect() implementations into agreement.
Replace infinite loops in atari_NCR5380.c with timeouts, as per NCR5380.c.
Remove 'abort' flag in NCR5380.c as per atari_NCR5380.c -- if reselection
fails, there may be no MESSAGE IN phase so don't attempt data transfer.
During selection, don't interfere with the chip registers after a
reselection interrupt intervenes.
Clean up some trivial issues with code style, comments and printk.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The workarounds for chip errata appear twice, in slightly different
forms. One is used when defined(REAL_DMA) || defined(REAL_DMA_POLL), the
other when defined(PSEUDO_DMA). In the PDMA case, the workarounds have
been made conditional on FLAG_NO_DMA_FIXUPS. Do the same for the DMA case,
to eliminate the READ_OVERRUNS macro.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The flags DMA_WORKS_RIGHT, FLAG_NCR53C400 and FLAG_HAS_LAST_BYTE_SENT
all mean the same thing, i.e. the chip is not a 538[01]. (More recent
devices such as the 53C80 have a 'Last Byte Sent' bit in the Target
Command Register as well as other fixes for End-of-DMA errata.)
These flags have no additional meanings since previous cleanup patches
eliminated the NCR53C400 macro, moved g_NCR5380-specific code out of the
core driver and standardized interrupt handling.
Use the FLAG_NO_DMA_FIXUP flag to suppress End-of-DMA errata workarounds,
for those cards and drivers that make use of the TCR_LAST_BYTE_SENT bit.
Remove the old flags.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SCSI bus protocol sometimes requires monitoring two related conditions
simultaneously. Enhance NCR5380_poll_politely() for this purpose, and
put it to use in the arbitration algorithm. It will also find use in
pseudo DMA.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Because interrupt handling is crucial to the core driver(s), all wrapper
drivers need to agree on this code. This patch removes discrepancies.
NCR5380_intr() in NCR5380.c has the following pointless loop that differs
from the code in atari_NCR5380.c.
done = 1;
do {
/* ... */
} while (!done);
The 'done' flag gets cleared when a reconnected command is to be processed
from the work queue. But in NCR5380.c, the flag is also used to cause the
interrupt conditions to be re-examined. Perhaps this was because
NCR5380_reselect() was expected to cause another interrupt, or perhaps
the remaining present interrupt conditions need to be handled after the
NCR5380_reselect() call?
Actually, both possibilities are bogus, as is the loop itself. It seems
have been overlooked in the hit-and-miss removal of scsi host instance
list iteration many years ago; see history/history.git commit 491447e1fcff
("[PATCH] next NCR5380 updates") and commit 69e1a9482e57 ("[PATCH] fix up
NCR5380 private data"). See also my earlier patch, "Always retry
arbitration and selection".
The datasheet says, "IRQ can be reset simply by reading the Reset
Parity/Interrupt Register". So don't treat the chip IRQ like a
level-triggered interrupt. Of the conditions that set the IRQ flag,
some are level-triggered and some are edge-triggered, which means IRQ
itself must be edge-triggered.
Some interrupt conditions are latched and some are not. Before clearing
the chip IRQ flag, clear all state that may cause it to be raised. That
means clearing the DMA Mode and Busy Monitor bits in the Mode Register
and clearing the host ID in the Select Enable register.
Also clean up some printk's and some comments. Keep atari_NCR5380.c and
NCR5380.c in agreement.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Configuring core drivers using macros like this one prevents re-unifying
the core driver forks, and prevents implementing the core driver as a
library or a platform driver.
The UNSAFE macro in particular is a poor workaround for the problem of
interrupt latency. Releasing the locks complicates things because then we
would have to handle the possibility of EH handler invocation during a
PDMA transfer.
The comments say that instead of using this macro, "you're going to be
better off twiddling with transfersize". I agree. Remove this stuff.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The complex main_running/queue_main mechanism is peculiar to
atari_NCR5380.c. It isn't SMP safe and offers little value given that
the work queue already offers concurrency management. Remove this
complexity to bring atari_NCR5380.c closer to NCR5380.c.
It is not a good idea to call the information transfer state machine from
queuecommand because, according to Documentation/scsi/scsi_mid_low_api.txt
that could happen in soft irq context. Fix this.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Each host instance now has it's own work queue so the main() work item can
sleep when necessary. That means we can use a simple work item rather than
a delayed work item. This brings NCR5380.c closer to atari_NCR5380.c.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When there is a queued command and no connected command, NCR5380_select()
is called and arbitration begins. The chip waits for BUS FREE once the
MR_ARBITRATE bit in the mode register is enabled. That means there is
no need to wait for BUS FREE after disconnecting.
There is presently no polling for BUS FREE after sending an ABORT or
other message that might lead to disconnection. It only happens after
COMMAND COMPLETE or DISCONNECT messages, which seems inconsistent.
Remove the polling for !BSY in the COMMAND COMPLETE and DISCONNECT
cases.
BTW, the comments say "avoid nasty timeouts" and perhaps BUS FREE polling
was somehow helpful back in Linux v0.99.14u, when it was introduced.
The relevant timeout is presently 1 second (for bus arbitration).
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Allow target selection to fail with a timeout instead of waiting in
infinite loops. This gets rid of the unused NCR_TIMEOUT macro, it is more
defensive and has proved helpful in debugging.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use timeouts in do_abort() in atari_NCR5380.c instead of infinite loops.
Also fix the kernel-doc comment. Keep the two core driver forks in sync.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NCR5380_poll_politely() returns either 0 (success) or -ETIMEDOUT. However,
in do_abort(), the return value is incorrectly taken to be the status
register value. This means that the bus is put into DATA OUT phase instead
of MESSAGE OUT. Fix this.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NCR5380_poll_politely() never returns -1. That means do_abort() can fail
to handle a timeout after waiting for the target to negate REQ. Fix this
and cleanup other NCR5380_poll_politely() call sites.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
MESSAGE REJECT does not imply DISCONNECT: the target is about to enter
MESSAGE IN or MESSAGE OUT phase.
This bug fix comes from atari_NCR5380.c. Unfortunately it never made it
into the original NCR5380.c core driver.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some old drivers partially implemented support for linked commands using
a "proposed" next_link pointer in struct scsi_cmnd that never actually
existed. Remove this code.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove the DEF_SCSI_QCMD macro (already removed from atari_NCR5380.c). The
lock provided by DEF_SCSI_QCMD is only needed for queue data structures.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to the SCSI-2 draft revision 10L, atari_NCR5380.c is correct
when it says that the phase lines are valid up until ACK is negated
following the transmission of the last byte in MESSAGE IN phase. This is
true for all information transfer phases, from target to initiator.
Sample the phase bits in STATUS_REG so that NCR5380_transfer_pio() can
return the correct result. The return value is presently unused (perhaps
because of bugs like this) but this change at least fixes the caller's
phase variable, which is passed by reference.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The atari_NCR5380.c and NCR5380.c core drivers differ in their handling of
target disconnection. This is partly because atari_NCR5380.c had all of
the polling and sleeping removed to become entirely interrupt-driven, and
it is partly because of damage done to NCR5380.c after atari_NCR5380.c was
forked. See commit 37cd23b44929 ("Linux 2.1.105") in history/history.git.
The polling changes that were made in v2.1.105 are questionable at best:
if REQ is not already asserted when NCR5380_transfer_pio() is invoked, and
if the expected phase is DATA IN or DATA OUT, the function will schedule
main() to execute after USLEEP_SLEEP jiffies and then return. The problems
here are the expected REQ timing and the sleep interval*. Avoid this issue
by using NCR5380_poll_politely() instead of scheduling main().
The atari_NCR5380.c core driver requires the use of the chip interrupt and
always permits target disconnection. It sets the cmd->device->disconnect
flag when a device disconnects, but never tests this flag.
The NCR5380.c core driver permits disconnection only when
instance->irq != NO_IRQ. It sets the cmd->device->disconnect flag when
a device disconnects and it tests this flag in a couple of places:
1. During NCR5380_information_transfer(), following COMMAND OUT phase,
if !cmd->device->disconnect, the initiator will take a guess as to
whether or not the target will then choose to go to MESSAGE IN phase
and disconnect. If the driver guesses "yes", it will schedule main()
to execute after USLEEP_SLEEP jiffies and then return there.
Unfortunately the driver may guess "yes" even after it has denied
the target the disconnection privilege. When the target does not
disconnect, the sleep can be beneficial, assuming the sleep interval
is appropriate (mostly it is not*).
And even if the driver guesses "yes" correctly, and the target would
then disconnect, the driver still has to go through the MESSAGE IN
phase in order to get to BUS FREE phase. The main loop can do nothing
useful until BUS FREE, and sleeping just delays the phase transition.
2. If !cmd->device->disconnect and REQ is not already asserted when
NCR5380_information_transfer() is invoked, the function polls for REQ
for USLEEP_POLL jiffies. If REQ is not asserted, it then schedules
main() to execute after USLEEP_SLEEP jiffies and returns.
The idea is apparently to yeild the CPU while waiting for REQ.
This is conditional upon !cmd->device->disconnect, but there seems
to be no rhyme or reason for that. For example, the flag may be
unset because disconnection privilege was denied because the driver
has no IRQ. Or the flag may be unset because the device has never
needed to disconnect before. Or if the flag is set, disconnection
may have no relevance to the present bus phase.
Another deficiency of the existing algorithm is as follows. When the
driver has no IRQ, it prevents disconnection, and generally polls and
sleeps more than it would normally. Now, if the driver is going to poll
anyway, why not allow the target to disconnect? That way the driver can do
something useful with the bus instead of polling unproductively!
Avoid this pointless latency, complexity and guesswork by using
NCR5380_poll_politely() instead of scheduling main().
* For g_NCR5380, the time intervals for USLEEP_SLEEP and USLEEP_POLL are
200 ms and 10 ms, respectively. They are 20 ms and 200 ms respectively
for the other NCR5380 drivers. There doesn't seem to be any reason for
this discrepancy. The timing seems to have no relation to the type of
adapter. Bizarrely, the timing in g_NCR5380 seems to relate only to one
particular type of target device. This patch attempts to solve the
problem for all NCR5380 drivers and all target devices.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Follow the example of the atari_NCR5380.c core driver and adopt the
NCR5380_dma_xfer_len() hook. Implement NCR5380_dma_xfer_len() for dtc.c
and g_NCR5380.c to take care of the limitations of these cards. Keep the
default for drivers using PSEUDO_DMA.
Eliminate the unused macro LIMIT_TRANSFERSIZE.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If NCR5380_select() returns -1, it means arbitration was lost or selection
failed and should be retried. If the main loop simply terminates when there
are still commands on the issue queue, they will remain queued until they
expire.
Fix this by clearing the 'done' flag after selection failure or lost
arbitration.
The "else break" clause in NCR5380_main() that gets removed here appears
to be a vestige of a long-gone loop that iterated over host instances.
See commit 491447e1fcff ("[PATCH] next NCR5380 updates") in
history/history.git.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Linux v2.1.105 changed the algorithm for polling for the BSY signal
in NCR5380_select() and NCR5380_main().
Presently, this code has a bug. Back then, NCR5380_set_timer(hostdata, 1)
meant reschedule main() after sleeping for 10 ms. Repeated 25 times this
provided the recommended 250 ms selection time-out delay. This got broken
when HZ became configurable.
We could fix this but there's no need to reschedule the main loop. This
BSY polling presently happens when the NCR5380_main() work queue item
calls NCR5380_select(), which in turn schedules NCR5380_main(), which
calls NCR5380_select() again, and so on.
This algorithm is a deviation from the simpler one in atari_NCR5380.c.
The extra complexity and state is pointless. There's no reason to
stop selection half-way and return to to the main loop when the main
loop can do nothing useful until selection completes.
So just poll for BSY. We can sleep while polling now that we have a
suitable workqueue.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When in process context, sleep during polling if doing so won't add
significant latency. In interrupt context or if the lock is held, poll
briefly then give up. Keep both core drivers in sync.
Calibrate busy-wait iterations to allow for variation in chip register
access times between different 5380 hardware implementations.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Allocate a work queue that will permit busy waiting and sleeping. This
means NCR5380_init() can potentially fail, so add this error path.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 8b801ead3d ("[ARM] rpc: update Acorn SCSI drivers to modern ecard
interfaces") neglected to remove a request_region() call in cumana_1.c.
Commit eda32612f7b2 ("[PATCH] give all LLDD driver a ->release method") in
history/history.git added some pointless release_region() calls in dtc.c,
pas16.c and t128.c.
Fix these issues.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Linux 2.1.105 introduced the USLEEP_WAITLONG delay, apparently "needed for
Mustek scanners". It is intended to stall the issue queue for 5 seconds.
There are a number of problems with this.
1. Only g_NCR5380 enables the delay, which implies that the other five
drivers using the NCR5380.c core driver remain incompatible with
Mustek scanners.
2. The delay is not implemented by atari_NCR5380.c, which is problematic
for re-unifying the two core driver forks.
3. The delay is implemented using NCR5380_set_timer() which makes it
unreliable. A new command queued by the mid-layer cancels the delay.
4. The delay is applied indiscriminately in several situations in which
NCR5380_select() returns -1. These are-- reselection by the target,
failure of the target to assert BSY, and failure of the target to
assert REQ. It's clear from the comments that USLEEP_WAITLONG is not
relevant to the reselection case. And reportedly, these scanners do
not disconnect.
5. atari_NCR5380.c was forked before Linux 2.1.105, so it was spared some
of the damage done to NCR5380.c. In this case, the atari_NCR5380.c core
driver was more standard-compliant and may not have needed any
workaround like the USLEEP_WAITLONG kludge. The compliance issue was
addressed in the previous patch.
If these scanners still don't work, we need a better solution. Retrying
selection until EH aborts a command offers equivalent robustness. Bugs in
the existing driver prevent EH working correctly but this is addressed in
a subsequent patch. Remove USLEEP_WAITLONG.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NCR5380.c is not compliant with the SCSI-2 standard (at least, not with
the draft revision 10L that I have to refer to). The selection algorithm
in atari_NCR5380.c is correct, so use that.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a target disappears from the SCSI bus, NCR5380_select() may
subsequently fail with a time-out. In this situation, scsi_done is
called and NCR5380_select() returns 0. Both hostdata->connected and
hostdata->selecting are NULL and the main loop should proceed with
the next command in the issue queue. Clarify this logic.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove the restart_select and targets_present variables introduced in
Linux v1.1.38. The former was used only for a questionable debug printk
and the latter "so we can call a select failure a retryable condition".
Well, retrying select failure in general is a different problem to a
target that doesn't assert BSY. We need to handle these two cases
differently; the latter case can be left to the SCSI ML.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The "failed" label in NCR5380_select() is not helpful. Some failures
return 0, others -1. Use return instead of goto to improve clarity and
brevity, like atari_NCR5380.c does. Fix the relevant comments.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove the duplicate write to the Select Enable Register that appeared
in v1.1.38.
Also remove the redundant write to Initiator Command Register prior to
calling do_abort().
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The aborted flag was introduced in v1.1.38 but never used. Remove it.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make use of do_reset() in the bus reset handler in atari_NCR5380.c. The
version in NCR5380.c already does so. Keep them in sync.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The atari_NCR5380.c core driver now takes care of bus reset upon driver
initialization if required (same as NCR5380.c). Move the Toshiba CD-ROM
support into the core driver, enabled with a host flag, so that all
NCR5380 drivers can make use of it.
Drop the RESET_BOOT macros and the ATARI_SCSI_RESET_BOOT and
ATARI_SCSI_TOSHIBA_DELAY Kconfig symbols, which are now redundant.
Remove the atari_scsi_reset_boot(), mac_scsi_reset_boot() and
sun3_scsi_reset_boot() routines. None of this duplicated code is needed
now that all drivers can use NCR5380_maybe_reset_bus().
This brings atari_scsi, mac_scsi and sun3_scsi into line with all of the
other NCR5380 drivers.
The bus reset may raise an interrupt. That would be new behaviour for
atari_scsi only when CONFIG_ATARI_SCSI_RESET_BOOT=n. The ST DMA interrupt
is not assigned to atari_scsi at this stage, so
CONFIG_ATARI_SCSI_RESET_BOOT=y may well be problematic already.
Regardless, do_reset() now raises and clears the interrupt within
local_irq_save/restore which should avoid problems.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Merge the bus reset code from NCR5380.c into atari_NCR5380.c. This allows
for removal of a lot of duplicated code conditional on the RESET_BOOT
macro (in the next patch).
The atari_NCR5380.c fork lacks the do_reset() and NCR5380_poll_politely()
routines from NCR5380.c, so introduce them. They are indispensible. Keep
the two implementations in sync.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move board-specific code like this,
NCR5380_write(C400_CONTROL_STATUS_REG, CSR_BASE);
from the core driver to the board driver. Eliminate the NCR53C400 macro
from the core driver. Removal of all macros like this one will be
necessary in order to have one core driver that can support all kinds of
boards.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch splits the NCR5380_init() function into two parts, similar
to the scheme used with atari_NCR5380.c. This avoids two problems.
Firstly, NCR5380_init() may perform a bus reset, which would cause the
chip to assert IRQ. The chip is unable to mask its bus reset interrupt.
Drivers can't call request_irq() before calling NCR5380_init(), because
initialization must happen before the interrupt handler executes. If
driver initialization causes an interrupt it may be problematic on some
platforms. To avoid that, first move the bus reset code into
NCR5380_maybe_reset_bus().
Secondly, NCR5380_init() contains some board-specific interrupt setup code
for the NCR53C400 that does not belong in the core driver. In moving this
code, better not re-order interrupt initialization and bus reset. Again,
the solution is to move the bus reset code into NCR5380_maybe_reset_bus().
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This macro makes the code cryptic. Remove it.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The NCR5380_local_declare and NCR5380_setup macros exist to define and
initialize a particular local variable, to provide the address of the
chip registers needed for the driver's implementation of its
NCR5380_read/write register access macros.
In cumana_1 and macscsi, these macros generate pointless code like this,
struct Scsi_Host *_instance;
_instance = instance;
In pas16, the use of NCR5380_read/write in pas16_hw_detect() requires that
the io_port local variable has been defined and initialized, but the
NCR5380_local_declare and NCR5380_setup macros can't be used for that
purpose because the Scsi_Host struct has not yet been instantiated.
Moreover, these macros were removed from atari_NCR5380.c long ago and
now they constitute yet another discrepancy between the two core driver
forks.
Remove these "optimizations".
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ASM macro is never defined. rtrc in pas16.c is not used.
NCR5380_map_config, do_NCR5380_intr, do_t128_intr and do_pas16_intr
are unused. NCR_NOT_SET harms readability. Remove them.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace {P,T,DTC}DEBUG_INIT with NDEBUG_INIT. Remove dead debugging
code, including code that's conditional upon *DEBUG_TRANSFER.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The NVRAM location of this byte is 16, as documented in
http://toshyp.atari.org/en/004009.html
This was confirmed by Michael Schmitz, by setting the SCSI host ID
under EmuTOS and then checking the value in /proc/driver/nvram and
/dev/nvram under Linux.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This drop enables a future card with a device id of 0x0600 to be
recognized by the cxlflash driver.
As per the design, the Accelerator Function Unit (AFU) for this new IBM
CXL Flash Adapter retains the same host interface as the previous
generation. For the early prototypes of the new card, the driver with
this change behaves exactly as the driver prior to this behaved with the
earlier generation card. Therefore, no card specific programming has
been added. These card specific changes can be staged in later if
needed.
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an async error interrupt is generated, and the error requires the FC
link to be reset, it cannot be performed in the interrupt context. So a
work element is scheduled to complete the link reset in a process
context. If either an EEH event or an escalation occurs in between when
the interrupt is generated and the scheduled work is started, the MMIO
space may no longer be available. This will cause an oops in the worker
thread.
[ 606.806583] NIP kthread_data+0x28/0x40
[ 606.806633] LR wq_worker_sleeping+0x30/0x100
[ 606.806694] Call Trace:
[ 606.806721] 0x50 (unreliable)
[ 606.806796] wq_worker_sleeping+0x30/0x100
[ 606.806884] __schedule+0x69c/0x8a0
[ 606.806959] schedule+0x44/0xc0
[ 606.807034] do_exit+0x770/0xb90
[ 606.807109] die+0x300/0x460
[ 606.807185] bad_page_fault+0xd8/0x150
[ 606.807259] handle_page_fault+0x2c/0x30
[ 606.807338] wait_port_offline.constprop.12+0x60/0x130 [cxlflash]
To prevent the problem space area from being unmapped, when there is
pending work, a mapcount (using the kref mechanism) is held. The
mapcount is released only when the work is completed. The last
reference release is tied to the unmapping service.
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After a few iterations of resetting the card, either during EEH
recovery, or a host_reset the following is seen in the logs. cxlflash
0008:00: cxlflash_queuecommand: could not get a free command
At every reset of the card, the commands that are outstanding are being
leaked. No effort is being made to reap these commands. A few more
resets later, the above error message floods the logs and the card is
rendered totally unusable as no free commands are available.
Iterated through the 'cmd' queue and printed out the 'free' counter and
found that on each reset certain commands were in-use and stayed in-use
through subsequent resets.
To resolve this issue, when the card is reset, reap all the commands
that are active/outstanding.
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Having a date for the driver requires it to be updated quite
often. Removing the date which is not necessary. Also made
use of the existing symbol to print the driver name.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Applications which use virtual LUN's that are backed by a physical LUN
over both adapter ports may experience an I/O failure in the event of a
link loss (e.g. cable pull).
Virtual LUNs may be accessed through one or both ports of the adapter.
This access is encoded in the translation entries that comprise the
virtual LUN and used by the AFU for load-balancing I/O and handling
failover scenarios. In a link loss scenario, even though the AFU is able
to maintain connectivity to the LUN, it is up to the application to
retry the failed I/O. When applications are unaware of the virtual LUN's
underlying topology, they are unable to make a sound decision of when to
retry an I/O and therefore are forced to make their reaction to a failed
I/O absolute. The result is either a failure to retry I/O or increased
latency for scenarios where a retry is pointless.
To remedy this scenario, provide feedback back to the application on
virtual LUN creation as to which ports the LUN may be accessed. LUN's
spanning both ports are candidates for a retry in a presence of an I/O
failure.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Acked-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The original fix to escalate a 'login timed out' error to a LINK_RESET
was only made for one of the two ports on the card. This fix resolves
the same issue for the second port (port 1).
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On the interrupt path, we repeatedly establish the pointer to the
storvsc_device. While the compiler does inline get_in_stor_device() (and
other static functions) in the call chain in the interrupt path, the
compiler is repeatedly inlining the call to get_in_stor_device() each
time it is invoked. The return value of get_in_stor_device() can be
cached in the interrupt path since there is higher level serialization
in place to ensure correct handling when the module unload races with
the processing of an incoming message from the host. Optimize this code
path by caching the pointer to storvsc_device and passing it as an
argument.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Long Li <longli@microsoft.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The function storvsc_channel_init() repeatedly interacts with the host
to extract various channel properties. Refactor this code to eliminate
code repetition.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Long Li <longli@microsoft.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For FC devices managed by this driver, atttach the appropriate transport
template. This will allow us to create the appropriate sysfs files for
these devices. With this we can publish the wwn for both the port and the node.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Long Li <longli@microsoft.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The hv_fc_wwn_packet is exchanged over vmbus. Make the definition in
Linux match the Windows definition.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Long Li <longli@microsoft.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add SGPIO support to Marvell 94xx.
Signed-off-by: Wilfried Weissmann <Wilfried.Weissmann@gmx.at>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It might happen that we try to free an already freed pointer.
Reported-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Chaitra P B <chaitra.basappa@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Adding a new method to display enclosure device information.
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SAS transport places devices on bus 0 but driver was setting the bus to
3.
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Left off some changes from Rasmus Villemoes where he changed snprintf to
scnprintf.
Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename the local definition of LIST_HEAD to BSD_LIST_HEAD. This fixes a
ctags error if we apply the C rules to header files as well:
ctags: Warning: drivers/scsi/aic7xxx/aic79xx.h:1072: null expansion of name pattern "\3"
ctags: Warning: drivers/scsi/aic7xxx/aic7xxx.h:919: null expansion of name pattern "\3"
Signed-off-by: Michal Marek <mmarek@suse.com>
The OPTIMAL TRANSFER LENGTH reported by scsi_debug is 64 blocks which
translates to 32KB with the default logical block size. That's much
lower than what real storage devices typically report (256KB to 1MB).
Bump the optimal transfer length to 1024 blocks.
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update version to 11.0.0.10 for upstream patch set
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch is to the lpfc_els.c which resolves following warning
reported by coccicheck:
WARNING: kzalloc should be used for rdp_context, instead of
kmalloc/memset
Signed-off-by: Punit Vara <punitvara@gmail.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The mempool_destroy() function tests whether its argument is NULL
and then returns immediately. Thus the test around the calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Reviewed-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add logging for misconfigured optics acqe reported by fw.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix external loopback failure.
Rx sequence reassembly was incorrect.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix mbox reuse in PLOGI completion. Moved allocations so that buffer
properly init'd.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use new FDMI speed definitions for 10G, 25G and 40G FCoE.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make write check error processing more resilient.
Checks to catch writes that fw reports weren't fully complete yet SCSI
status indicated fine needed correction.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix RDP ACC being too long.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix RDP Speed reporting.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modularize, cleanup, add comments - for FDMI code in driver
Note: I don't like the comments with leading # - but as we have a lot if
present, I'm deferring to handle it in one big fix later.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix crash in fcp command completion path.
Missed null check.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix driver crash when module parameter lpfc_fcp_io_channel set to 16
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix RegLogin failed error seen on Lancer FC during port bounce
Fix the statemachine and ref counting.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the FLOGI discovery logic to comply with T11 standards
We weren't properly setting fabric parameters, such as R_A_TOV and E_D_TOV,
when we registered the vfi object in default configs and pt2pt configs.
Revise to now pass service params with the values to the firmware and
ensure they are reset on link bounce. Required reworking the call sequence
in the discovery threads.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix FCF Infinite loop in lpfc_sli4_fcf_rr_next_index_get.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Eryu Guan reported that loading scsi_debug would fail. This turned out
to be caused by scsi_debug reporting an optimal I/O size of 32KB which
is smaller than the 64KB page size on the PowerPC system in question.
Add a check to ensure that we only use the device-reported OPTIMAL
TRANSFER LENGTH if it is bigger than or equal to the page cache size.
Reported-by: Eryu Guan <guaneryu@gmail.com>
Reported-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current discovery routines use the VPD 0x83 inquiry page to find
the device SAS address and match it to the end point in the enclosure.
This doesn't work for SATA devices because expanders (or hosts) simply
make up an endpoint address for STP and thus the address returned by
the VPD page never matches. Instead of doing this, for SAS attached
devices, match by the direct endpoint address instead.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
For a device known to be SAS connected, this will return the endpoint
address. This is useful for getting the SAS address of SATA devices.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Adds a function designed to be callable any time (regardless of
whether the transport attributes are configured or not) which returns
true if the device is attached over a SAS transport. The design of
this function is that transport specific functions can be embedded
within a
if (is_sas_attached(sdev)) {
...
}
which would be compiled out (and thus eliminate the symbols) if SAS is
not configured.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
It is preferred that drivers use platform_get_irq() instead of
irq_of_parse_and_map(), so replace.
Signed-off-by: John Garry <john.garry@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When setting up CRC offload set ip_summed to CHECKSUM_PARTIAL
instead of CHECKSUM_UNNECESSARY. This is consistent with the
definition of CHECKSUM_PARTIAL.
The only driver that seems to be advertising NETIF_F_FCOE_CRC is
ixgbe. AFICT the driver does not look at ip_summed for FCOE and
just assumes that CRC is being offloaded.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no good reason to keep them apart, and this makes using the API
a bit simpler.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
There is no good reason to start out disabled - drivers can control if
the poll instance can be scheduled by simply not scheduling it yet.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
The new name is irq_poll as iopoll is already taken. Better suggestions
welcome.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
KASAN found that our additional element processing scripts drop off
the end of the VPD page into unallocated space. The reason is that
not every element has additional information but our traversal
routines think they do, leading to them expecting far more additional
information than is present. Fix this by adding a gate to the
traversal routine so that it only processes elements that are expected
to have additional information (list is in SES-2 section 6.1.13.1:
Additional Element Status diagnostic page overview)
Reported-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Tested-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There were a couple cases where the error codes weren't set and also I
changed the success return to "return 0;" which is the same as
"return rc;" but more explicit.
Fixes: 42e7a69368 ('hisi_sas: Add ssp command functio')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If char is signed and one of these bytes happen to have a value outside
the ascii range, the corresponding output will consist of "ffffff"
followed by the two hex chars that were actually intended. One way to
fix it would be to change the casts to (u8*) aka
(unsigned char*), but it is much simpler (and generates smaller code)
to use the %ph extension which was created for such short hexdumps.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Boaz Harrosh <ooo@electrozaur.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce a logging level for storvsc to log certain error/warning
messages. Those messages are helpful in some environments,
e.g. Microsoft Azure, for customer support and troubleshooting purposes.
Signed-off-by: Long Li <longli@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is missing calls to pci_dma_mapping_error() after
performing the DMA mapping, which caused DMA-API warning to
show up in dmesg's output. Though that happens only when
DMA_API_DEBUG option is enabled. This change fixes the issue
and makes pvscsi_map_buffers() function more robust.
Signed-off-by: Arvind Kumar <arvindkumar@vmware.com>
Cc: Josh Boyer <jwboyer@fedoraproject.org>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
IS_ERR_OR_NULL already contain an unlikely compiler flag. Drop it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Acked-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The "> MAX_CONTEXT" should be ">= MAX_CONTEXT". Otherwise we go one
step beyond the end of the cfg->ctx_tbl[] array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This reverts commit 49718f0fb8 ("SCSI: Fix NULL pointer dereference in
runtime PM")
The old commit may lead to a issue that blk_{pre|post}_runtime_suspend and
blk_{pre|post}_runtime_resume may not be called in pairs.
Take sr device as example, when sr device goes to runtime suspend,
blk_{pre|post}_runtime_suspend will be called since sr device defined
pm->runtime_suspend. But blk_{pre|post}_runtime_resume will not be called
since sr device doesn't have pm->runtime_resume. so, sr device can not
resume correctly anymore.
More discussion can be found from below link.
http://marc.info/?l=linux-scsi&m=144163730531875&w=2
Signed-off-by: Ken Xue <Ken.Xue@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Xiangliang Yu <Xiangliang.Yu@amd.com>
Cc: James E.J. Bottomley <JBottomley@odin.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Michael Terry <Michael.terry@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Simple enclosure implementations (mostly USB) are allowed to return only
page 8 to every diagnostic query. That really confuses our
implementation because we assume the return is the page we asked for and
end up doing incorrect offsets based on bogus information leading to
accesses outside of allocated ranges. Fix that by checking the page
code of the return and giving an error if it isn't the one we asked for.
This should fix reported bugs with USB storage by simply refusing to
attach to enclosures that behave like this. It's also good defensive
practise now that we're starting to see more USB enclosures.
Reported-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: stable@vger.kernel.org
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
