1. changes some register address to fit macro definition
2. add platform data and clock for sdhc
Signed-off-by: Yong Shen <yong.shen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
1. Adjust FEC base address name to fit macro definition
2. Add platform data and reset function for FEC
Signed-off-by: Yong Shen <yong.shen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
1. pll_base address should return right value
2. uart parent clk is from pll3
Signed-off-by: Yong Shen <yong.shen@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
MX27_3DS board has a MC13783 PMIC connected to the CSPI2 port.
Add support for the PMIC.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Current code doesn't really enable the usb clocks so if they're disabled
when booting linux, the kernel/machine will hang as soon as someone is trying
to read a usb register
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch is fixing some issues :
- MXC_OTG_UCTRL_OPM_BIT is for USBCTRL register and not PHYCTRL register.
- the MXC_EHCI_WAKEUP_ENABLED check was only clearing the bits so never allows
to set them.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add basic function and uart device support.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
mx5 SoCs have different GPIO port count.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There are 2 versions of the timrot on Freescale MXS-based SoCs.
The v1 on MX23 only gets 16 bits counter, while v2 on MX28
extends the counter to 32 bits.
The implementation uses two timers, one for clock_event and
another for clocksource. MX28 uses timrot 0 and 1, while MX23
uses 0 and 2.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
- DEBUG_LL support, which is incompatible with multi-soc MXS image
because of different DUART base address on MX23 and MX28
- uncompress message support
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
- The mxs wdog is implemented in RTC block.
- There is a generic software reset routine for most modules on mxs.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This iomux file has been constructed from the Freescale pinmux tool.
It contains all pins from the tool, but the datasheet lists some
configurations not present in the tool, these are not yet added.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch actually replaces the 'struct pad_desc' with a u64 cookie
to facilitate adding platform specific pad_ctrl settings to an
existing pad definition.
So, instead of:
iomux_v3_cfg_t power_key = MX51_PAD_EIM_A27__GPIO_2_21;
power_key.pad_ctrl = MX51_GPIO_PAD_CTRL_2;
mxc_iomux_v3_setup_pad(&power_key);
one can write:
mxc_iomux_v3_setup_pad((MX51_PAD_EIM_A27__GPIO_2_21 & ~MUX_PAD_CTRL_MASK) | MX51_GPIO_PAD_CTRL_2);
Patch applies to branch 'imx-for-2.6.38' of git://git.pengutronix.de/git/imx/linux-2.6
Signed-Off-By: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When building as module:
ERROR: "cpufreq_gov_performance" [arch/arm/plat-mxc/cpufreq.ko] undefined!
WARNING: modpost: Found 1 section mismatch(es).
To see full details build your kernel with:
'make CONFIG_DEBUG_SECTION_MISMATCH=y'
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
It's due to the driver using CPUFREQ_DEFAULT_GOVERNOR, even it should not
(see commit 8122c6cea0 in Linus tree), so
remove it.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for FIQ on mx51 TZIC
TZIC changes tested with FIQ audio on an mx51 board
AVIC changes build with mx3_defconfig, not tested
Signed-off-by: Peter Horton <phorton@bitbox.co.uk>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Use clk_get to acquire the watchdog clock and also avoid hardcoding the clock name.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
