Increment the mgmt revision due to recent changes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_cmd_sync_queue shall return an error if HCI_UNREGISTER flag has
been set as that means hci_unregister_dev has been called so it will
likely cause a uaf after the timeout as the hdev will be freed.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add power reset for bluetooth via enable-gpios in h5_btrtl_open function.
While testing the RTL8822CS SDIO WiFi/BT adapter, it was found that in
some cases the kernel could not initialize BT firmware. However,
manually resetting the adapter via gpio (off/on sequence) allows it to
start correctly.
Apparently, when the system starts, the adapter is in an undefined state
(including unknown gpio state after starting uboot). A forced reset helps
to initialize the adapter in most cases. It has been found experimentally
that 100 ms is sufficient for a reset.
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add a variation of RTL8822CS with hci_ver = 0x08. This is fully similar
to RTL8822CS with hci_ver = 0x0a observed on the Tanix TX6 Android
set-top box and JetHome JetHub H1.
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Signed-off-by: Rudi Heitbaum <rudi@heitbaum.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
HCI_EV_VENDOR is in fact variable length since it acts as metaevent
where a vendor can implement their own event sets.
In addition to it this makes use of bt_dev_warn_ratelimited to supress
the amount of logging in case the event has more data than expected.
Fixes: 3e54c5890c ("Bluetooth: hci_event: Use of a function table to handle HCI event")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The invalid SCO handle error is normally caused by a race in the USB
transport where the data and event happen to be 2 different endpoints
so the event carrying the SCO handle is processed after its data.
Note: This can probably be resolved with use of force_poll_sync
debugfs.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When one of the three connection complete events is received multiple
times for the same handle, the device is registered multiple times which
leads to memory corruptions. Therefore, consequent events for a single
connection are ignored.
The conn->state can hold different values, therefore HCI_CONN_HANDLE_UNSET
is introduced to identify new connections. To make sure the events do not
contain this or another invalid handle HCI_CONN_HANDLE_MAX and checks
are introduced.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=215497
Signed-off-by: Soenke Huster <soenke.huster@eknoes.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
msft_find_handle_data returns NULL if it can't find the handle.
Therefore, handle_data must be checked, otherwise a null pointer
is dereferenced.
Signed-off-by: Soenke Huster <soenke.huster@eknoes.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently, there is a loop in btmtksdio_txrx_work() which iteratively
executes until the variable int_status is zero.
But the variable int_status should be masked out with the actual interrupt
sources (MTK_REG_CHISR bit 0-15) before we check the loop condition.
Otherwise, RX_PKT_LEN (MTK_REG_CHISR bit 16-31) which is read-only and
unclearable would cause the loop to get stuck on some chipsets like
MT7663s.
Fixes: 26270bc189 ("Bluetooth: btmtksdio: move interrupt service to work")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Apply sleep mode by default and a smaller idle time to reduce power
consumption further.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Lower its log level from INFO to DEBUG prior to we enable runtime pm for
mt7921s with the smaller idle time as default.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to the firmware behavior (even the oldest one in linux-firmware)
If the firmware is downloaded, MT7921S must rely on the additional mailbox
mechanism that resides in firmware to check if the device is the right
state for btmtksdio_mcu_[drv|fw]_pmctrl(). Otherwise, we still apply the
old way for that.
That is a necessary patch before we enable runtime pm for mt7921s as
default.
Fixes: c603bf1f94 ("Bluetooth: btmtksdio: add MT7921s Bluetooth support")
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Mark Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to chip hw flow, mt7921s need to re-acquire privilege
again before normal running. Otherwise, the bus may be stuck in
an abnormal status.
Fixes: c603bf1f94 ("Bluetooth: btmtksdio: add MT7921s Bluetooth support")
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Mark Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Refactor btmtksdio_runtime_[suspend|resume]() to create the common
funcitons btmtksdio_[fw|drv]_pmctrl() shared with btmtksdio_[open|close]()
to avoid the redundant code as well.
This is also a prerequisite patch for the incoming patches.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Mark Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to the MCU firmware behavior, as the driver is aware of the
notification of the interrupt source FW_MAILBOX_INT that shows the MCU
completed delivered a core dump piece to the host, the driver must
acknowledge the MCU with the register PH2DSM0R bit PH2DSM0R_DRIVER_OWN
to notify the MCU to handle the next core dump piece.
Fixes: db57b62591 ("Bluetooth: btmtksdio: add support of processing firmware coredump and log")
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Mark Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
kvartet reported, that hci_uart_tx_wakeup() uses uninitialized rwsem.
The problem was in wrong place for percpu_init_rwsem() call.
hci_uart_proto::open() may register a timer whose callback may call
hci_uart_tx_wakeup(). There is a chance, that hci_uart_register_device()
thread won't be fast enough to call percpu_init_rwsem().
Fix it my moving percpu_init_rwsem() call before p->open().
INFO: trying to register non-static key.
The code is fine but needs lockdep annotation, or maybe
you didn't initialize this object before use?
turning off the locking correctness validator.
CPU: 2 PID: 18524 Comm: syz-executor.5 Not tainted 5.16.0-rc6 #9
...
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
assign_lock_key kernel/locking/lockdep.c:951 [inline]
register_lock_class+0x148d/0x1950 kernel/locking/lockdep.c:1263
__lock_acquire+0x106/0x57e0 kernel/locking/lockdep.c:4906
lock_acquire kernel/locking/lockdep.c:5637 [inline]
lock_acquire+0x1ab/0x520 kernel/locking/lockdep.c:5602
percpu_down_read_trylock include/linux/percpu-rwsem.h:92 [inline]
hci_uart_tx_wakeup+0x12e/0x490 drivers/bluetooth/hci_ldisc.c:124
h5_timed_event+0x32f/0x6a0 drivers/bluetooth/hci_h5.c:188
call_timer_fn+0x1a5/0x6b0 kernel/time/timer.c:1421
Fixes: d73e172816 ("Bluetooth: hci_serdev: Init hci_uart proto_lock to avoid oops")
Reported-by: Yiru Xu <xyru1999@gmail.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch changes the kernel-doc style comment block to common comment
block. These files don't support kernel-doc style so no need to use the
kernel-doc style. Also, they cause the warning when W=1 option is used
as below.
drivers/bluetooth/hci_ll.c:518: warning: Function parameter or member 'lldev' not described in 'download_firmware'
drivers/bluetooth/btmrvl_debugfs.c:29: warning: cannot understand function prototype: 'struct btmrvl_debugfs_data '
drivers/bluetooth/btmrvl_sdio.c:36: warning: expecting prototype for Marvell BT-over-SDIO driver(). Prototype was for VERSION() instead
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Properly align the list items of the quirk for readability.
No functional changes intended. Trivial stuff.
Fixes: 0671c06623 ("Bluetooth: btusb: Add workaround for remote-wakeup issues with Barrot 8041a02 fake CSR controllers")
Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the flag to identify the Intel legacy ROM products that
don't support WBS like WP and StP.
Fixes: 3df4dfbec0 ("Bluetooth: btintel: Move hci quirks to setup routine")
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduces two new MGMT events for notifying the bluetoothd
whenever the controller starts/stops monitoring a device.
Test performed:
- Verified by logs that the MSFT Monitor Device is received from the
controller and the bluetoothd is notified whenever the controller
starts/stops monitoring a device.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Miao-chen Chou <mcchou@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Whenever the controller starts/stops monitoring a bt device, it sends
MSFT Monitor Device event. Add handler to read this vendor event.
Test performed:
- Verified by logs that the MSFT Monitor Device event is received from
the controller whenever it starts/stops monitoring a device.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Miao-chen Chou <mcchou@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This event is just specified for SCO and eSCO link types.
On the reception of a HCI_Synchronous_Connection_Complete for a BDADDR
of an existing LE connection, LE link type and a status that triggers the
second case of the packet processing a NULL pointer dereference happens,
as conn->link is NULL.
Signed-off-by: Soenke Huster <soenke.huster@eknoes.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add unlocks to two error paths in hci_inquiry_result_with_rssi_evt().
Fixes: fee645033e ("Bluetooth: hci_event: Use skb_pull_data when processing inquiry results")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Have "..reg (%d)" to be consistent with the other similar error messages.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
move struct reg_read_cmd to btmtk.h to allow other mtk drivers refer to.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The driver has to issue the specific command to enable Bluetooth SCO over
the I2S/PCM interface on mt7921s, that is supported since the firmware
with version 20211222191101 was added, and the patch would not cause any
harm even when the old firmware is applied.
The SCO profile with the patch was tested by setting up a VOIP application,
connected to HFP device, checked telephony function can work normally.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Mark Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Enable wake on bluetooth on mt7921s that can be supported since the
firmware with version 20211129211059 was added, and the patch would
not cause any harm even when the old firmware is applied.
The patch was tested by setting up an HID or HOGP profile to connect a
Bluetooth keyboard and mouse, then putting the system to suspend, then
trying to wake up the system by moving the Bluetooth keyboard or mouse,
and then checking if the system can wake up and be brought back to
the normal state.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Mark Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Using "btmtksdio" as the prefix instead of "btsdio"
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This fixes the following warning:
net/bluetooth/hci_sync.c:5143:5: warning: no previous prototype for
‘hci_le_ext_create_conn_sync’ [-Wmissing-prototypes]
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After this parameter is passed in, there is no usage, and deleting it will
not bring any impact.
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Benjamin Yim <yan2228598786@gmail.com>
Link: https://lore.kernel.org/r/20220109130824.2776-1-yan2228598786@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
Moreover, dma_set_mask_and_coherent() returns 0 or -EIO, so the return
code of the function can be used directly.
Finally, inline bnx2x_set_coherency_mask() because it is now only a wrapper
for a single dma_set_mask_and_coherent() call.
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/29608a525876afddceabf8f11b2ba606da8748fc.1641730747.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
Moreover, dma_set_mask_and_coherent() returns 0 or -EIO, so the return
code of the function can be used directly. There is no need to 'rc = -EIO'
explicitly.
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/b9aa46e7e5a5aa61f56aac5ea439930f41ad9946.1641726804.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
So if dma_set_mask_and_coherent() succeeds, 'netdev->features' will have
NETIF_F_HIGHDMA in all cases. Move the assignment of this feature in
be_netdev_init() instead be_probe() which is a much logical place.
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/637696d7141faa68c29fc34b70f9aa67d5e605f0.1641718999.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As stated in [1], dma_set_mask() with a 64-bit mask will never fail if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
So, if dma_set_mask_and_coherent() succeeds, 'using_dac' is known to be
'true'. This variable can be removed.
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/1d5a7b3f4fa735f1233c3eb3fa07e71df95fad75.1641658516.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As stated in [1], dma_set_mask() with a 64-bit mask will never fail if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
If dma_set_mask_and_coherent() succeeds, 'ap->pci_using_dac' is known to be
1. So 'pci_using_dac' can be removed from the 'struct ace_private'.
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/1a414c05c27b21c661aef61dffe1adcd1578b1f5.1641651917.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As stated in [1], dma_set_mask() with a 64-bit mask will never fail if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
So qlcnic_set_dma_mask(), (in qlcnic_main.c) can be simplified a lot and
inlined directly in its only caller.
If dma_set_mask_and_coherent() succeeds, 'pci_using_dac' is known to be 1.
So it can be removed from all the calling chain.
qlcnic_setup_netdev() can finally be simplified as-well.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/4996ab0337d62ec6a54b2edf234cd5ced4b4d7ad.1641649611.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kees reports quoted commit introduced the following warning on arm64:
drivers/net/ethernet/allwinner/sun4i-emac.c:922:60: error: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'resource_size_t' {aka 'long long unsigned int'} [-Werror=format=]
922 | netdev_info(ndev, "get io resource from device: 0x%x, size = %u\n",
| ~^
| | | unsigned int
| %llx
923 | regs->start, resource_size(regs));
| ~~~~~~~~~~~
| |
| resource_size_t {aka long long unsigned int}
.. and another one like that for resource_size().
Switch to %pa and a cast.
Reported-by: Kees Cook <keescook@chromium.org>
Fixes: 47869e82c8 ("sun4i-emac.c: add dma support")
Link: https://lore.kernel.org/r/20220108034438.2227343-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As page_pool_refill_alloc_cache() is only called by
__page_pool_get_cached(), which assumes non-concurrent access
as suggested by the comment in __page_pool_get_cached(), and
ptr_ring allows concurrent access between consumer and producer,
so remove the spinlock in page_pool_refill_alloc_cache().
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/r/20220107090042.13605-1-linyunsheng@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
