Previously we calculated the upstream and downstream L0s and L1 exit
latencies of the link in pcie_aspm_cap_init() and cached them in struct
pcie_link_state.latency_*.
These values are only used in pcie_aspm_check_latency() where they are
compared with the acceptable latencies on the link. This path is used when
removing or changing the D state of the device, so it's relatively low
frequency.
To reduce the amount of per-link data we store, remove the latency_*
entries from struct pcie_link_state and calculate the latencies directly
where they are needed.
Link: https://lore.kernel.org/r/20211119193732.12343-3-refactormyself@gmail.com
Signed-off-by: Saheed O. Bolarinwa <refactormyself@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move pci_function_0() earlier so we can use it from other functions.
Link: https://lore.kernel.org/r/20211119193732.12343-2-refactormyself@gmail.com
Signed-off-by: Bolarinwa O. Saheed <refactormyself@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The Power Fault Detected bit in the Slot Status register differs from
all other hotplug events in that it is sticky: It can only be cleared
after turning off slot power. Per PCIe r5.0, sec. 6.7.1.8:
If a power controller detects a main power fault on the hot-plug slot,
it must automatically set its internal main power fault latch [...].
The main power fault latch is cleared when software turns off power to
the hot-plug slot.
The stickiness used to cause interrupt storms and infinite loops which
were fixed in 2009 by commits 5651c48cfa ("PCI pciehp: fix power fault
interrupt storm problem") and 99f0169c17 ("PCI: pciehp: enable
software notification on empty slots").
Unfortunately in 2020 the infinite loop issue was inadvertently
reintroduced by commit 8edf5332c3 ("PCI: pciehp: Fix MSI interrupt
race"): The hardirq handler pciehp_isr() clears the PFD bit until
pciehp's power_fault_detected flag is set. That happens in the IRQ
thread pciehp_ist(), which never learns of the event because the hardirq
handler is stuck in an infinite loop. Fix by setting the
power_fault_detected flag already in the hardirq handler.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214989
Link: https://lore.kernel.org/linux-pci/DM8PR11MB5702255A6A92F735D90A4446868B9@DM8PR11MB5702.namprd11.prod.outlook.com
Fixes: 8edf5332c3 ("PCI: pciehp: Fix MSI interrupt race")
Link: https://lore.kernel.org/r/66eaeef31d4997ceea357ad93259f290ededecfd.1637187226.git.lukas@wunner.de
Reported-by: Joseph Bao <joseph.bao@intel.com>
Tested-by: Joseph Bao <joseph.bao@intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.19+
Cc: Stuart Hayes <stuart.w.hayes@gmail.com>
Advertise support of the Gen4 automotive variants in module's device ID
table and add the same IDs to the list of switchtec quirks.
Link: https://lore.kernel.org/r/20211119003803.2333-2-kelvin.cao@microchip.com
Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
When config pci_ops.read() can detect failed PCI transactions, the data
returned to the CPU is PCI_ERROR_RESPONSE (~0 or 0xffffffff).
Obviously a successful PCI config read may *also* return that data if a
config register happens to contain ~0, so it doesn't definitively indicate
an error unless we know the register cannot contain ~0.
Use PCI_POSSIBLE_ERROR() to check the response we get when we read data
from hardware. This unifies PCI error response checking and makes error
checks consistent and easier to find.
Link: https://lore.kernel.org/r/b12005c0d57bb9d4c8b486724d078b7bd92f8321.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When config pci_ops.read() can detect failed PCI transactions, the data
returned to the CPU is PCI_ERROR_RESPONSE (~0 or 0xffffffff).
Obviously a successful PCI config read may *also* return that data if a
config register happens to contain ~0, so it doesn't definitively indicate
an error unless we know the register cannot contain ~0.
Use PCI_POSSIBLE_ERROR() to check the response we get when we read data
from hardware. This unifies PCI error response checking and makes error
checks consistent and easier to find.
Compile tested only.
Link: https://lore.kernel.org/r/679ce049bccf10df3ca9ef4918ee2c3235afdaea.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When config pci_ops.read() can detect failed PCI transactions, the data
returned to the CPU is PCI_ERROR_RESPONSE (~0 or 0xffffffff).
Obviously a successful PCI config read may *also* return that data if a
config register happens to contain ~0, so it doesn't definitively indicate
an error unless we know the register cannot contain ~0.
Use PCI_POSSIBLE_ERROR() to check the response we get when we read data
from hardware. This unifies PCI error response checking and makes error
checks consistent and easier to find.
Compile tested only.
Link: https://lore.kernel.org/r/9b0632f1f183432149f495cf12bdd5a72cc597a4.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When config pci_ops.read() can detect failed PCI transactions, the data
returned to the CPU is PCI_ERROR_RESPONSE (~0 or 0xffffffff).
Obviously a successful PCI config read may *also* return that data if a
config register happens to contain ~0, so it doesn't definitively indicate
an error unless we know the register cannot contain ~0.
Use PCI_POSSIBLE_ERROR() to check the response we get when we read data
from hardware. This unifies PCI error response checking and makes error
checks consistent and easier to find.
Compile tested only.
Link: https://lore.kernel.org/r/e185b052fbfd530df703a36dd31126cb870eed95.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lukas Wunner <lukas@wunner.de>
When config pci_ops.read() can detect failed PCI transactions, the data
returned to the CPU is PCI_ERROR_RESPONSE (~0 or 0xffffffff).
Obviously a successful PCI config read may *also* return that data if a
config register happens to contain ~0, so it doesn't definitively indicate
an error unless we know the register cannot contain ~0.
Use PCI_POSSIBLE_ERROR() to check the response we get when we read data
from hardware. This unifies PCI error response checking and makes error
checks consistent and easier to find.
Link: https://lore.kernel.org/r/ed01cad87a2e35f3865275b5fb34290817a1ebf8.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Derrick <jonathan.derrick@linux.dev>
When config pci_ops.read() can detect failed PCI transactions, the data
returned to the CPU is PCI_ERROR_RESPONSE (~0 or 0xffffffff).
Obviously a successful PCI config read may *also* return that data if a
config register happens to contain ~0, so it doesn't definitively indicate
an error unless we know the register cannot contain ~0.
Use PCI_POSSIBLE_ERROR() to check the response we get when we read data
from hardware. This unifies PCI error response checking and makes error
checks consistent and easier to find.
Link: https://lore.kernel.org/r/f4d18d470cb90f9cb52ea155b01528ba2e76e8d6.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If config pci_ops.read() methods return failure, the PCI_OP_READ() and
PCI_USER_READ_CONFIG() wrappers use PCI_SET_ERROR_RESPONSE() to set the
data value, so there's no need to set it in the pci_ops.read() methods
themselves.
Drop the unnecessary data value fabrication when pci_ops.read() fails.
Link: https://lore.kernel.org/r/50f9a6fa16521a86cb24d2f27c1f66eb3568cb9a.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If config pci_ops.read() methods return failure, the PCI_OP_READ() and
PCI_USER_READ_CONFIG() wrappers use PCI_SET_ERROR_RESPONSE() to set the
data value, so there's no need to set it in the pci_ops.read() methods
themselves.
Drop the unnecessary data value fabrication when pci_ops.read() fails.
Link: https://lore.kernel.org/r/83540eb3ae76a0d28bbe03d69d685a6d549b456b.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
If config pci_ops.read() methods return failure, the PCI_OP_READ() and
PCI_USER_READ_CONFIG() wrappers use PCI_SET_ERROR_RESPONSE() to set the
data value, so there's no need to set it in the pci_ops.read() methods
themselves.
Drop the unnecessary data value fabrication when pci_ops.read() fails.
Link: https://lore.kernel.org/r/ed5020e5b008b28c33a90c9c1670cef2393d3b7e.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If config pci_ops.read() methods return failure, the PCI_OP_READ() and
PCI_USER_READ_CONFIG() wrappers use PCI_SET_ERROR_RESPONSE() to set the
data value, so there's no need to set it in the pci_ops.read() methods
themselves.
Drop the unnecessary data value fabrication when pci_ops.read() fails.
Link: https://lore.kernel.org/r/f30264b137b1282ffda34d336e8060bb13d60b98.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If config pci_ops.read() methods return failure, the PCI_OP_READ() and
PCI_USER_READ_CONFIG() wrappers use PCI_SET_ERROR_RESPONSE() to set the
data value, so there's no need to set it in the pci_ops.read() methods
themselves.
Drop the unnecessary data value fabrication when pci_ops.read() fails.
Link: https://lore.kernel.org/r/335014f2b44cdf24ed1e37cb7c88f6c5de896cc2.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
If config pci_ops.read() methods return failure, the PCI_OP_READ() and
PCI_USER_READ_CONFIG() wrappers use PCI_SET_ERROR_RESPONSE() to set the
data value, so there's no need to set it in the pci_ops.read() methods
themselves.
Drop the unnecessary data value fabrication when pci_ops.read() fails.
Link: https://lore.kernel.org/r/f87e22bc09a471d2cf15ad05dfd6432f57739aed.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If config pci_ops.read() methods return failure, the PCI_OP_READ() and
PCI_USER_READ_CONFIG() wrappers use PCI_SET_ERROR_RESPONSE() to set the
data value, so there's no need to set it in the pci_ops.read() methods
themselves.
Drop the unnecessary data value fabrication when pci_ops.read() fails.
Link: https://lore.kernel.org/r/7da7ea760abc5f85cad6e9b0d3e59eebd93f50d3.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If config pci_ops.read() methods return failure, the PCI_OP_READ() and
PCI_USER_READ_CONFIG() wrappers use PCI_SET_ERROR_RESPONSE() to set the
data value, so there's no need to set it in the pci_ops.read() methods
themselves.
Drop the unnecessary data value fabrication when pci_ops.read() fails.
Link: https://lore.kernel.org/r/765c2f27d85fcee4eb137023dc0a8f864eee9e36.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If config pci_ops.read() methods return failure, the PCI_OP_READ() and
PCI_USER_READ_CONFIG() wrappers use PCI_SET_ERROR_RESPONSE() to set the
data value, so there's no need to set it in the pci_ops.read() methods
themselves.
Drop the unnecessary data value fabrication when pci_ops.read() fails.
Link: https://lore.kernel.org/r/666127469482f9ca177805ff52aeb7bccb26e4c9.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If config pci_ops.read() methods return failure, the PCI_OP_READ() and
PCI_USER_READ_CONFIG() wrappers use PCI_SET_ERROR_RESPONSE() to set the
data value, so there's no need to set it in the pci_ops.read() methods
themselves.
Drop the unnecessary data value fabrication when pci_ops.read() fails.
Link: https://lore.kernel.org/r/b95defa3db834789a4207df5d6b0216c8b610524.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If config pci_ops.read() methods return failure, the PCI_OP_READ() and
PCI_USER_READ_CONFIG() wrappers use PCI_SET_ERROR_RESPONSE() to set the
data value, so there's no need to set it in the pci_ops.read() methods
themselves.
Drop the unnecessary data value fabrication when pci_ops.read() fails.
Link: https://lore.kernel.org/r/22f471b638276422926c49f3d42ac41bc7b28b3d.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If config pci_ops.read() methods return failure, the PCI_OP_READ() and
PCI_USER_READ_CONFIG() wrappers use PCI_SET_ERROR_RESPONSE() to set the
data value, so there's no need to set it in the pci_ops.read() methods
themselves.
Drop the unnecessary data value fabrication when pci_ops.read() fails.
Link: https://lore.kernel.org/r/1b2edb060cf19b45f70645b331e6c08c9ba798c0.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
A config read from a PCI device that doesn't exist or doesn't respond
causes a PCI error. There's no real data to return to satisfy the CPU read,
so most hardware fabricates ~0 data.
Use PCI_SET_ERROR_RESPONSE() to set the error response when we think the
device has already been disconnected.
This helps unify PCI error response checking and make error checks
consistent and easier to find.
Link: https://lore.kernel.org/r/29db0a6874716db80757e4e3cdd03562f13eb0cb.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When a PCI config read fails, most PCI host bridges fabricate ~0 data to
complete the CPU read. But some host bridges do not; their drivers may
only return an error from the pci_ops.read() method.
In PCI_OP_READ() and PCI_USER_READ_CONFIG(), use PCI_SET_ERROR_RESPONSE()
to set the data value to indicate an error when pci_ops.read() fails.
This means the host bridge driver no longer needs to fabricate error data
when they detect errors.
This makes error response fabrication consistent and helps in removal of a
lot of repeated code.
Suggested-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/4188fc5465631ce0d472d1423de3d9fb2f09b8ff.1637243717.git.naveennaidu479@gmail.com
Signed-off-by: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Pali Rohár <pali@kernel.org>
Currently set_pcie_thunderbolt() open-codes pci_find_vsec_capability().
Refactor the former to use the latter. No functional change intended.
Link: https://lore.kernel.org/r/20211115112902.24033-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
- Core code:
A regression fix for the Open Firmware interrupt mapping code where a
interrupt controller property in a node caused a map property in the
same node to be ignored.
- Interrupt chip drivers:
- Workaround a limitation in SiFive PLIC interrupt chip which silently
ignores an EOI when the interrupt line is masked.
- Provide the missing mask/unmask implementation for the CSKY MP
interrupt controller.
- PCI/MSI:
- Prevent a use after free when PCI/MSI interrupts are released by
destroying the sysfs entries before freeing the memory which is
accessed in the sysfs show() function.
- Implement a mask quirk for the Nvidia ION AHCI chip which does not
advertise masking capability despite implementing it. Even worse the
chip comes out of reset with all MSI entries masked, which due to the
missing masking capability never get unmasked.
- Move the check which prevents accessing the MSI[X] masking for XEN
back into the low level accessors. The recent consolidation missed
that these accessors can be invoked from places which do not have
that check which broke XEN. Move them back to he original place
instead of sprinkling tons of these checks all over the code.
-----BEGIN PGP SIGNATURE-----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=LBQL
-----END PGP SIGNATURE-----
Merge tag 'irq-urgent-2021-11-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A set of fixes for the interrupt subsystem
Core code:
- A regression fix for the Open Firmware interrupt mapping code where
a interrupt controller property in a node caused a map property in
the same node to be ignored.
Interrupt chip drivers:
- Workaround a limitation in SiFive PLIC interrupt chip which
silently ignores an EOI when the interrupt line is masked.
- Provide the missing mask/unmask implementation for the CSKY MP
interrupt controller.
PCI/MSI:
- Prevent a use after free when PCI/MSI interrupts are released by
destroying the sysfs entries before freeing the memory which is
accessed in the sysfs show() function.
- Implement a mask quirk for the Nvidia ION AHCI chip which does not
advertise masking capability despite implementing it. Even worse
the chip comes out of reset with all MSI entries masked, which due
to the missing masking capability never get unmasked.
- Move the check which prevents accessing the MSI[X] masking for XEN
back into the low level accessors. The recent consolidation missed
that these accessors can be invoked from places which do not have
that check which broke XEN. Move them back to he original place
instead of sprinkling tons of these checks all over the code"
* tag 'irq-urgent-2021-11-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
of/irq: Don't ignore interrupt-controller when interrupt-map failed
irqchip/sifive-plic: Fixup EOI failed when masked
irqchip/csky-mpintc: Fixup mask/unmask implementation
PCI/MSI: Destroy sysfs before freeing entries
PCI: Add MSI masking quirk for Nvidia ION AHCI
PCI/MSI: Deal with devices lying about their MSI mask capability
PCI/MSI: Move non-mask check back into low level accessors
- Add PCI automatic error recovery.
- Fix tape driver timer initialization broken during timers api cleanup.
- Fix bogus CPU measurement counters values on CPUs offlining.
- Check the validity of subchanel before reading other fields in
the schib in cio code.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAmGPwDMACgkQjYWKoQLX
FBgCoQf/VBel0vDex9NNVo59OmGTNh9NPPT2cUU8vYEmwHfaBeInZVEx5WOxXijl
8MIbEgi6Wt3EwnIghjouC50nk8jCiNOJ8Z/wG+01zZpVpLk2GvKGjxoYxKg+5E6T
sOSr7TMeKOtOp23xKAXGVIzzkrDTSyr3qruTKg/m6TFhQ0XSm/ld2k6tR5AARbuB
UtsxBOtPWyHm1xPyuhjr+c6riK2vGQwJwYya4vGtIW8ix9uZoPabdqqzWsD3meBc
B6fe96YQGxA8Tt80FtyJ6pHEhNDr8CE656aJZNJCnd7q1RmLWC1R/aUme+9wqQtO
i9YmMvc+uzgQonpo+YgWqu9fIQqcXA==
=OjW1
-----END PGP SIGNATURE-----
Merge tag 's390-5.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Vasily Gorbik:
- Add PCI automatic error recovery.
- Fix tape driver timer initialization broken during timers api
cleanup.
- Fix bogus CPU measurement counters values on CPUs offlining.
- Check the validity of subchanel before reading other fields in the
schib in cio code.
* tag 's390-5.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/cio: check the subchannel validity for dev_busid
s390/cpumf: cpum_cf PMU displays invalid value after hotplug remove
s390/tape: fix timer initialization in tape_std_assign()
s390/pci: implement minimal PCI error recovery
PCI: Export pci_dev_lock()
s390/pci: implement reset_slot for hotplug slot
s390/pci: refresh function handle in iomap
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAmGNcPYUHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vxTvQ//Wl8O7D+ckdw/4xMVi2N2uc6vCbB6
or5wmW1jfE6H7YvXbUrSMEBFoRfaz9nhuT3w9i60hzYmc9uqbsMCONBHLFAaILCP
By/qkNgMFuskZGHTziqsf2Qfza04KQDv4quUl8SvlUfQeOtzUXe0vtXCrFmMTDGs
QQ/bbVbI6WazTwzC11NALU3Kc8AZQXQMkd5Nt4fBfuZwFhBfnEckJgF3PmSZ7PpO
N/29wJDsdkHSBNqTO1eeqdVIN8GQ6aycUYEQp3gvDCvwQ3CXtPP6SScTnqibbzjO
3wuBk+FFH8Zdq8e7CEYoj0mL2RMKhLrY1MLV8IGI1YiPy8pH1EujOiDG0uNk7YSg
Zqo3NMq9L2IR28odTMc8W8oknz6CTO+rhoW22CbyImtrPT5RnWsyj1xH+k2lMxt/
3viTV5lDzKr6V6c5xdhCP26eNzt06mlrduvQ5EvsfGu6whckyrgd6XOppExdWA/S
24N9GCJuZRCp5wgETq+Vxl48ZWLzkJ3IwoVrIhx4UTChvXPIgYrviGnEFp64ZCuc
FbrINeeddxWdXkkuJ44FhmSkv7Gcl87w0cofy9tnArxZza5v3wGATFp7G1z8WO+0
HWoBhdeGGQ3+ClJUo9ihO2r9hABUbveJqxgjQbCs8P/7bR0acCoeGJCoZVj7KUUe
a6GDw16Lfu87QuQ=
=0aFC
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.16-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Revert conversion to struct device.driver instead of struct
pci_dev.driver.
The device.driver is set earlier, and using it caused the PCI core to
call driver PM entry points before .probe() and after .remove(), when
the driver isn't prepared.
This caused NULL pointer dereferences in i2c_designware_pci and
probably other driver issues"
* tag 'pci-v5.16-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "PCI: Use to_pci_driver() instead of pci_dev->driver"
Revert "PCI: Remove struct pci_dev->driver"
This reverts commit 2a4d9408c9.
Robert reported a NULL pointer dereference caused by the PCI core
(local_pci_probe()) calling the i2c_designware_pci driver's
.runtime_resume() method before the .probe() method. i2c_dw_pci_resume()
depends on initialization done by i2c_dw_pci_probe().
Prior to 2a4d9408c9 ("PCI: Use to_pci_driver() instead of
pci_dev->driver"), pci_pm_runtime_resume() avoided calling the
.runtime_resume() method because pci_dev->driver had not been set yet.
2a4d9408c9 and b5f9c644eb ("PCI: Remove struct pci_dev->driver"),
removed pci_dev->driver, replacing it by device->driver, which *has* been
set by this time, so pci_pm_runtime_resume() called the .runtime_resume()
method when it previously had not.
Fixes: 2a4d9408c9 ("PCI: Use to_pci_driver() instead of pci_dev->driver")
Link: https://lore.kernel.org/linux-i2c/CAP145pgdrdiMAT7=-iB1DMgA7t_bMqTcJL4N0=6u8kNY3EU0dw@mail.gmail.com/
Reported-by: Robert Święcki <robert@swiecki.net>
Tested-by: Robert Święcki <robert@swiecki.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This reverts commit b5f9c644eb.
Revert b5f9c644eb ("PCI: Remove struct pci_dev->driver"), which is needed
to revert 2a4d9408c9 ("PCI: Use to_pci_driver() instead of
pci_dev->driver").
2a4d9408c9 caused a NULL pointer dereference reported by Robert Święcki.
Details in the revert of that commit.
Fixes: 2a4d9408c9 ("PCI: Use to_pci_driver() instead of pci_dev->driver")
Link: https://lore.kernel.org/linux-i2c/CAP145pgdrdiMAT7=-iB1DMgA7t_bMqTcJL4N0=6u8kNY3EU0dw@mail.gmail.com/
Reported-by: Robert Święcki <robert@swiecki.net>
Tested-by: Robert Święcki <robert@swiecki.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
free_msi_irqs() frees the MSI entries before destroying the sysfs entries
which are exposing them. Nothing prevents a concurrent free while a sysfs
file is read and accesses the possibly freed entry.
Move the sysfs release ahead of freeing the entries.
Fixes: 1c51b50c29 ("PCI/MSI: Export MSI mode using attributes, not kobjects")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87sfw5305m.ffs@tglx
It appears that some devices are lying about their mask capability,
pretending that they don't have it, while they actually do.
The net result is that now that we don't enable MSIs on such
endpoint.
Add a new per-device flag to deal with this. Further patches will
make use of it, sadly.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20211104180130.3825416-2-maz@kernel.org
Cc: Bjorn Helgaas <helgaas@kernel.org>
The recent rework of PCI/MSI[X] masking moved the non-mask checks from the
low level accessors into the higher level mask/unmask functions.
This missed the fact that these accessors can be invoked from other places
as well. The missing checks break XEN-PV which sets pci_msi_ignore_mask and
also violates the virtual MSIX and the msi_attrib.maskbit protections.
Instead of sprinkling checks all over the place, lift them back into the
low level accessor functions. To avoid checking three different conditions
combine them into one property of msi_desc::msi_attrib.
[ josef: Fixed the missed conversion in the core code ]
Fixes: fcacdfbef5 ("PCI/MSI: Provide a new set of mask and unmask functions")
Reported-by: Josef Johansson <josef@oderland.se>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Josef Johansson <josef@oderland.se>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: stable@vger.kernel.org
BMIPS_GENERIC denotes support for the MIPS-based Broadcom STB platforms
which this driver can support.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
- Fix support for platforms that do not enumerate every ACPI0016 (CXL
Host Bridge) in the CHBS (ACPI Host Bridge Structure).
- Introduce a common pci_find_dvsec_capability() helper, clean up open
coded implementations in various drivers.
- Add 'cxl_test' for regression testing CXL subsystem ABIs. 'cxl_test'
is a module built from tools/testing/cxl/ that mocks up a CXL topology
to augment the nascent support for emulation of CXL devices in QEMU.
- Convert libnvdimm to use the uuid API.
- Complete the definition of CXL namespace labels in libnvdimm.
- Tunnel libnvdimm label operations from nd_ioctl() back to the CXL
mailbox driver. Enable 'ndctl {read,write}-labels' for CXL.
- Continue to sort and refactor functionality into distinct driver and
core-infrastructure buckets. For example, mailbox handling is now a
generic core capability consumed by the PCI and cxl_test drivers.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSbo+XnGs+rwLz9XGXfioYZHlFsZwUCYYRtyQAKCRDfioYZHlFs
Z7UsAP9DzUN6IWWnYk1R95YXYVxFriRtRsBjujAqTg49EMghawEAoHaA9lxO3Hho
l25TLYUOmB/zFTlUbe6YQptMJZ5YLwY=
=im9j
-----END PGP SIGNATURE-----
Merge tag 'cxl-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull cxl updates from Dan Williams:
"More preparation and plumbing work in the CXL subsystem.
From an end user perspective the highlight here is lighting up the CXL
Persistent Memory related commands (label read / write) with the
generic ioctl() front-end in LIBNVDIMM.
Otherwise, the ability to instantiate new persistent and volatile
memory regions is still on track for v5.17.
Summary:
- Fix support for platforms that do not enumerate every ACPI0016 (CXL
Host Bridge) in the CHBS (ACPI Host Bridge Structure).
- Introduce a common pci_find_dvsec_capability() helper, clean up
open coded implementations in various drivers.
- Add 'cxl_test' for regression testing CXL subsystem ABIs.
'cxl_test' is a module built from tools/testing/cxl/ that mocks up
a CXL topology to augment the nascent support for emulation of CXL
devices in QEMU.
- Convert libnvdimm to use the uuid API.
- Complete the definition of CXL namespace labels in libnvdimm.
- Tunnel libnvdimm label operations from nd_ioctl() back to the CXL
mailbox driver. Enable 'ndctl {read,write}-labels' for CXL.
- Continue to sort and refactor functionality into distinct driver
and core-infrastructure buckets. For example, mailbox handling is
now a generic core capability consumed by the PCI and cxl_test
drivers"
* tag 'cxl-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl: (34 commits)
ocxl: Use pci core's DVSEC functionality
cxl/pci: Use pci core's DVSEC functionality
PCI: Add pci_find_dvsec_capability to find designated VSEC
cxl/pci: Split cxl_pci_setup_regs()
cxl/pci: Add @base to cxl_register_map
cxl/pci: Make more use of cxl_register_map
cxl/pci: Remove pci request/release regions
cxl/pci: Fix NULL vs ERR_PTR confusion
cxl/pci: Remove dev_dbg for unknown register blocks
cxl/pci: Convert register block identifiers to an enum
cxl/acpi: Do not fail cxl_acpi_probe() based on a missing CHBS
cxl/pci: Disambiguate cxl_pci further from cxl_mem
Documentation/cxl: Add bus internal docs
cxl/core: Split decoder setup into alloc + add
tools/testing/cxl: Introduce a mock memory device + driver
cxl/mbox: Move command definitions to common location
cxl/bus: Populate the target list at decoder create
tools/testing/cxl: Introduce a mocked-up CXL port hierarchy
cxl/pmem: Add support for multiple nvdimm-bridge objects
cxl/pmem: Translate NVDIMM label commands to CXL label commands
...
Commit e3a9b1212b ("PCI: Export pci_dev_trylock() and pci_dev_unlock()")
already exported pci_dev_trylock()/pci_dev_unlock() however in some
circumstances such as during error recovery it makes sense to block
waiting to get full access to the device so also export pci_dev_lock().
Link: https://lore.kernel.org/all/20210928181014.GA713179@bhelgaas/
Acked-by: Pierre Morel <pmorel@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
This is done by adding a zpci_hot_reset_device() call which does a low
level reset of the PCI function without changing its higher level
function state. This way it can be used while the zPCI function is bound
to a driver and with DMA tables being controlled either through the
IOMMU or DMA APIs which is prohibited when using zpci_disable_device()
as that drop existing DMA translations.
As this reset, unlike a normal FLR, also calls zpci_clear_irq() we need
to implement arch_restore_msi_irqs() and make sure we re-enable IRQs for
the PCI function if they were previously disabled.
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----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=nsMh
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Conserve IRQs by setting up portdrv IRQs only when there are users
(Jan Kiszka)
- Rework and simplify _OSC negotiation for control of PCIe features
(Joerg Roedel)
- Remove struct pci_dev.driver pointer since it's redundant with the
struct device.driver pointer (Uwe Kleine-König)
Resource management:
- Coalesce contiguous host bridge apertures from _CRS to accommodate
BARs that cover more than one aperture (Kai-Heng Feng)
Sysfs:
- Check CAP_SYS_ADMIN before parsing user input (Krzysztof
Wilczyński)
- Return -EINVAL consistently from "store" functions (Krzysztof
Wilczyński)
- Use sysfs_emit() in endpoint "show" functions to avoid buffer
overruns (Kunihiko Hayashi)
PCIe native device hotplug:
- Ignore Link Down/Up caused by resets during error recovery so
endpoint drivers can remain bound to the device (Lukas Wunner)
Virtualization:
- Avoid bus resets on Atheros QCA6174, where they hang the device
(Ingmar Klein)
- Work around Pericom PI7C9X2G switch packet drop erratum by using
store and forward mode instead of cut-through (Nathan Rossi)
- Avoid trying to enable AtomicOps on VFs; the PF setting applies to
all VFs (Selvin Xavier)
MSI:
- Document that /sys/bus/pci/devices/.../irq contains the legacy INTx
interrupt or the IRQ of the first MSI (not MSI-X) vector (Barry
Song)
VPD:
- Add pci_read_vpd_any() and pci_write_vpd_any() to access anywhere
in the possible VPD space; use these to simplify the cxgb3 driver
(Heiner Kallweit)
Peer-to-peer DMA:
- Add (not subtract) the bus offset when calculating DMA address
(Wang Lu)
ASPM:
- Re-enable LTR at Downstream Ports so they don't report Unsupported
Requests when reset or hot-added devices send LTR messages
(Mingchuang Qiao)
Apple PCIe controller driver:
- Add driver for Apple M1 PCIe controller (Alyssa Rosenzweig, Marc
Zyngier)
Cadence PCIe controller driver:
- Return success when probe succeeds instead of falling into error
path (Li Chen)
HiSilicon Kirin PCIe controller driver:
- Reorganize PHY logic and add support for external PHY drivers
(Mauro Carvalho Chehab)
- Support PERST# GPIOs for HiKey970 external PEX 8606 bridge (Mauro
Carvalho Chehab)
- Add Kirin 970 support (Mauro Carvalho Chehab)
- Make driver removable (Mauro Carvalho Chehab)
Intel VMD host bridge driver:
- If IOMMU supports interrupt remapping, leave VMD MSI-X remapping
enabled (Adrian Huang)
- Number each controller so we can tell them apart in
/proc/interrupts (Chunguang Xu)
- Avoid building on UML because VMD depends on x86 bare metal APIs
(Johannes Berg)
Marvell Aardvark PCIe controller driver:
- Define macros for PCI_EXP_DEVCTL_PAYLOAD_* (Pali Rohár)
- Set Max Payload Size to 512 bytes per Marvell spec (Pali Rohár)
- Downgrade PIO Response Status messages to debug level (Marek Behún)
- Preserve CRS SV (Config Request Retry Software Visibility) bit in
emulated Root Control register (Pali Rohár)
- Fix issue in configuring reference clock (Pali Rohár)
- Don't clear status bits for masked interrupts (Pali Rohár)
- Don't mask unused interrupts (Pali Rohár)
- Avoid code repetition in advk_pcie_rd_conf() (Marek Behún)
- Retry config accesses on CRS response (Pali Rohár)
- Simplify emulated Root Capabilities initialization (Pali Rohár)
- Fix several link training issues (Pali Rohár)
- Fix link-up checking via LTSSM (Pali Rohár)
- Fix reporting of Data Link Layer Link Active (Pali Rohár)
- Fix emulation of W1C bits (Marek Behún)
- Fix MSI domain .alloc() method to return zero on success (Marek
Behún)
- Read entire 16-bit MSI vector in MSI handler, not just low 8 bits
(Marek Behún)
- Clear Root Port I/O Space, Memory Space, and Bus Master Enable bits
at startup; PCI core will set those as necessary (Pali Rohár)
- When operating as a Root Port, set class code to "PCI Bridge"
instead of the default "Mass Storage Controller" (Pali Rohár)
- Add emulation for PCI_BRIDGE_CTL_BUS_RESET since aardvark doesn't
implement this per spec (Pali Rohár)
- Add emulation of option ROM BAR since aardvark doesn't implement
this per spec (Pali Rohár)
MediaTek MT7621 PCIe controller driver:
- Add MediaTek MT7621 PCIe host controller driver and DT binding
(Sergio Paracuellos)
Qualcomm PCIe controller driver:
- Add SC8180x compatible string (Bjorn Andersson)
- Add endpoint controller driver and DT binding (Manivannan
Sadhasivam)
- Restructure to use of_device_get_match_data() (Prasad Malisetty)
- Add SC7280-specific pcie_1_pipe_clk_src handling (Prasad Malisetty)
Renesas R-Car PCIe controller driver:
- Remove unnecessary includes (Geert Uytterhoeven)
Rockchip DesignWare PCIe controller driver:
- Add DT binding (Simon Xue)
Socionext UniPhier Pro5 controller driver:
- Serialize INTx masking/unmasking (Kunihiko Hayashi)
Synopsys DesignWare PCIe controller driver:
- Run dwc .host_init() method before registering MSI interrupt
handler so we can deal with pending interrupts left by bootloader
(Bjorn Andersson)
- Clean up Kconfig dependencies (Andy Shevchenko)
- Export symbols to allow more modular drivers (Luca Ceresoli)
TI DRA7xx PCIe controller driver:
- Allow host and endpoint drivers to be modules (Luca Ceresoli)
- Enable external clock if present (Luca Ceresoli)
TI J721E PCIe driver:
- Disable PHY when probe fails after initializing it (Christophe
JAILLET)
MicroSemi Switchtec management driver:
- Return error to application when command execution fails because an
out-of-band reset has cleared the device BARs, Memory Space Enable,
etc (Kelvin Cao)
- Fix MRPC error status handling issue (Kelvin Cao)
- Mask out other bits when reading of management VEP instance ID
(Kelvin Cao)
- Return EOPNOTSUPP instead of ENOTSUPP from sysfs show functions
(Kelvin Cao)
- Add check of event support (Logan Gunthorpe)
Miscellaneous:
- Remove unused pci_pool wrappers, which have been replaced by
dma_pool (Cai Huoqing)
- Use 'unsigned int' instead of bare 'unsigned' (Krzysztof
Wilczyński)
- Use kstrtobool() directly, sans strtobool() wrapper (Krzysztof
Wilczyński)
- Fix some sscanf(), sprintf() format mismatches (Krzysztof
Wilczyński)
- Update PCI subsystem information in MAINTAINERS (Krzysztof
Wilczyński)
- Correct some misspellings (Krzysztof Wilczyński)"
* tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (137 commits)
PCI: Add ACS quirk for Pericom PI7C9X2G switches
PCI: apple: Configure RID to SID mapper on device addition
iommu/dart: Exclude MSI doorbell from PCIe device IOVA range
PCI: apple: Implement MSI support
PCI: apple: Add INTx and per-port interrupt support
PCI: kirin: Allow removing the driver
PCI: kirin: De-init the dwc driver
PCI: kirin: Disable clkreq during poweroff sequence
PCI: kirin: Move the power-off code to a common routine
PCI: kirin: Add power_off support for Kirin 960 PHY
PCI: kirin: Allow building it as a module
PCI: kirin: Add MODULE_* macros
PCI: kirin: Add Kirin 970 compatible
PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge
PCI: apple: Set up reference clocks when probing
PCI: apple: Add initial hardware bring-up
PCI: of: Allow matching of an interrupt-map local to a PCI device
of/irq: Allow matching of an interrupt-map local to an interrupt controller
irqdomain: Make of_phandle_args_to_fwspec() generally available
PCI: Do not enable AtomicOps on VFs
...
- Use PCI_VENDOR_ID_AMCC macro instead of defining a custom macro in
pci-xgene.c (Pali Rohár)
* remotes/lorenzo/pci/xgene:
PCI: xgene: Use PCI_VENDOR_ID_AMCC macro
- Assign a number to each VMD controller to distinguish them in
/proc/interrupts (Chunguang Xu)
- Don't disable VMD MSI-X remapping if IOMMU remapping is enabled (Adrian
Huang)
- Add Kconfig dependency on !UML for allyesconfig build issue (Johannes
Berg)
* remotes/lorenzo/pci/vmd:
PCI: vmd: depend on !UML
PCI: vmd: Do not disable MSI-X remapping if interrupt remapping is enabled by IOMMU
PCI: vmd: Assign a number to each VMD controller
- Reorganize to separate out PHY logic (Mauro Carvalho Chehab)
- Add support for external PHY in addition to the internal PHY (Mauro
Carvalho Chehab)
- Use regmap so both kirin driver and PHY can access APB registers (Mauro
Carvalho Chehab)
- Add support for per-lane PERST# GPIOs on HiKey970 external PEX 8606 PCI
bridge (Mauro Carvalho Chehab)
- Add "hisilicon,kirin970-pcie" compatible string (Mauro Carvalho Chehab)
- Add MODULE_* macros (Mauro Carvalho Chehab)
- Allow building as a module (Mauro Carvalho Chehab)
- Add power_off support for Kirin 960 PHY (Mauro Carvalho Chehab)
- Disable clkreq during poweroff sequence (Mauro Carvalho Chehab)
- De-init the dwc driver during remove (Mauro Carvalho Chehab)
- Allow removal of kirin driver (Mauro Carvalho Chehab)
* pci/host/kirin:
PCI: kirin: Allow removing the driver
PCI: kirin: De-init the dwc driver
PCI: kirin: Disable clkreq during poweroff sequence
PCI: kirin: Move the power-off code to a common routine
PCI: kirin: Add power_off support for Kirin 960 PHY
PCI: kirin: Allow building it as a module
PCI: kirin: Add MODULE_* macros
PCI: kirin: Add Kirin 970 compatible
PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge
PCI: kirin: Use regmap for APB registers
PCI: kirin: Add support for a PHY layer
PCI: kirin: Reorganize the PHY logic inside the driver
- Use sysfs_emit() in "show" functions instead of sprintf() to avoid buffer
overruns (Kunihiko Hayashi)
* remotes/lorenzo/pci/endpoint:
PCI: endpoint: Use sysfs_emit() in "show" functions
- Export dw_pcie_ep_reset_bar(), dw_pcie_link_up() so more drivers can be
modular (Luca Ceresoli)
- Allow dra7xx host and endpoint drivers to be modules (Luca Ceresoli)
- Enable dra7xx optional external clock if present (Luca Ceresoli)
- Clean up Kconfig dependencies for PCIE_DW_HOST- and PCIE_DW_EP-based
drivers (Andy Shevchenko)
- Remove visconti redundant dev_err() after platform_get_irq_byname()
failure (Krzysztof Wilczyński)
- Run dwc .host_init() method before registering MSI interrupt handler so
we have a chance to deal with pending interrupts left by bootloader
(Bjorn Andersson)
- Serialize uniphier INTx masking/unmasking (Kunihiko Hayashi)
* pci/host/dwc:
PCI: uniphier: Serialize INTx masking/unmasking and fix the bit operation
PCI: dwc: Perform host_init() before registering msi
PCI: visconti: Remove surplus dev_err() when using platform_get_irq_byname()
PCI: dwc: Clean up Kconfig dependencies (PCIE_DW_EP)
PCI: dwc: Clean up Kconfig dependencies (PCIE_DW_HOST)
PCI: dra7xx: Get an optional clock
PCI: dra7xx: Remove unused include
PCI: dra7xx: Make it a kernel module
PCI: dwc: Export more symbols to allow modular drivers
- Make of_phandle_args_to_fwspec() generally available (Marc Zyngier)
- Allow matching of interrupt-maps local to interrupt controller or PCI
device (Marc Zyngier)
- Add Apple SoC (e.g., M1) PCIe host controller driver, which enables
access to USB type-A, Ethernet, Wi-Fi, Bluetooth devices; these require
additional drivers of their own (Alyssa Rosenzweig)
- Add apple INTx, per-port, and MSI interrupt support (Marc Zyngier)
- Configure apple Requester-ID-to-Stream-ID mapper for IOMMU (DART) support
(Marc Zyngier)
* pci/host/apple:
PCI: apple: Configure RID to SID mapper on device addition
iommu/dart: Exclude MSI doorbell from PCIe device IOVA range
PCI: apple: Implement MSI support
PCI: apple: Add INTx and per-port interrupt support
PCI: apple: Set up reference clocks when probing
PCI: apple: Add initial hardware bring-up
PCI: of: Allow matching of an interrupt-map local to a PCI device
of/irq: Allow matching of an interrupt-map local to an interrupt controller
irqdomain: Make of_phandle_args_to_fwspec() generally available
- Define macros for PCI_EXP_DEVCTL_PAYLOAD_* (Pali Rohár)
- Set Max Payload Size to 512 bytes per Marvell spec (Pali Rohár)
- Downgrade PIO Response Status messages to debug level (Marek Behún)
- Preserve CRS SV (Config Request Retry Software Visibility) bit in
emulated Root Control register (Pali Rohár)
- Fix issue in configuring reference clock (Pali Rohár)
- Don't clear status bits for masked interrupts (Pali Rohár)
- Don't mask unused interrupts (Pali Rohár)
- Avoid code repetition in advk_pcie_rd_conf() (Marek Behún)
- Retry config accesses on CRS response (Pali Rohár)
- Simplify emulated Root Capabilities initialization (Pali Rohár)
- Fix several link training issues (Pali Rohár)
- Fix link-up checking via LTSSM (Pali Rohár)
- Fix reporting of Data Link Layer Link Active (Pali Rohár)
- Fix emulation of W1C bits (Marek Behún)
- Fix MSI domain .alloc() method to return zero on success (Marek Behún)
- Read entire 16-bit MSI vector in MSI handler, not just low 8 bits (Marek
Behún)
- Clear Root Port I/O Space, Memory Space, and Bus Master Enable bits at
startup; PCI core will set those as necessary (Pali Rohár)
- When operating as a Root Port, set class code to "PCI Bridge" instead of
the default "Mass Storage Controller" (Pali Rohár)
- Add emulation for PCI_BRIDGE_CTL_BUS_RESET since aardvark doesn't
implement this per spec (Pali Rohár)
- Add emulation of option ROM BAR since aardvark doesn't implement this per
spec (Pali Rohár)
* remotes/lorenzo/pci/aardvark:
PCI: aardvark: Fix support for PCI_ROM_ADDRESS1 on emulated bridge
PCI: aardvark: Fix support for PCI_BRIDGE_CTL_BUS_RESET on emulated bridge
PCI: aardvark: Set PCI Bridge Class Code to PCI Bridge
PCI: aardvark: Fix support for bus mastering and PCI_COMMAND on emulated bridge
PCI: aardvark: Read all 16-bits from PCIE_MSI_PAYLOAD_REG
PCI: aardvark: Fix return value of MSI domain .alloc() method
PCI: pci-bridge-emul: Fix emulation of W1C bits
PCI: aardvark: Fix reporting Data Link Layer Link Active
PCI: aardvark: Fix checking for link up via LTSSM state
PCI: aardvark: Fix link training
PCI: aardvark: Simplify initialization of rootcap on virtual bridge
PCI: aardvark: Implement re-issuing config requests on CRS response
PCI: aardvark: Deduplicate code in advk_pcie_rd_conf()
PCI: aardvark: Do not unmask unused interrupts
PCI: aardvark: Do not clear status bits of masked interrupts
PCI: aardvark: Fix configuring Reference clock
PCI: aardvark: Fix preserving PCI_EXP_RTCTL_CRSSVE flag on emulated bridge
PCI: aardvark: Don't spam about PIO Response Status
PCI: aardvark: Fix PCIe Max Payload Size setting
PCI: Add PCI_EXP_DEVCTL_PAYLOAD_* macros
- Tidy setup-irq.c comments (Pranay Sanghai)
- Fix misspellings (Krzysztof Wilczyński)
- Fix sprintf(), sscanf() format mismatches (Krzysztof Wilczyński)
- Tidy cpqphp code formatting (Krzysztof Wilczyński)
- Remove unused pci_pool wrappers, which have been replaced by dma_pool
(Cai Huoqing)
- Remove a redundant initialization in __pci_reset_function_locked() (Colin
Ian King)
- Use 'unsigned int' instead of 'unsigned' (Krzysztof Wilczyński)
- Update PCI subsystem information in MAINTAINERS (Krzysztof Wilczyński)
- Include generic <linux/> headers instead of <asm/> for cpqphp and vmd
(Krzysztof Wilczyński)
* pci/misc:
PCI: vmd: Drop redundant includes of <asm/device.h>, <asm/msi.h>
PCI: cpqphp: Use <linux/io.h> instead of <asm/io.h>
MAINTAINERS: Update PCI subsystem information
PCI: Prefer 'unsigned int' over bare 'unsigned'
PCI: Remove redundant 'rc' initialization
PCI: Remove unused pci_pool wrappers
PCI: cpqphp: Format if-statement code block correctly
PCI: Use unsigned to match sscanf("%x") in pci_dev_str_match_path()
PCI: hv: Remove unnecessary use of %hx
PCI: Correct misspelled and remove duplicated words
PCI: Tidy comments
- Add pci_read_vpd_any(), pci_write_vpd_any() to access VPD at arbitrary
offsets (Heiner Kallweit)
- Use VPD API to replace custom code in cxgb3 driver (Heiner Kallweit)
* pci/vpd:
cxgb3: Remove seeprom_write and use VPD API
cxgb3: Use VPD API in t3_seeprom_wp()
cxgb3: Remove t3_seeprom_read and use VPD API
PCI/VPD: Use pci_read_vpd_any() in pci_vpd_size()
PCI/VPD: Add pci_read/write_vpd_any()
- Avoid bus resets on Atheros QCA6174, since they hang (Ingmar Klein)
- Use store and forward mode on Pericom PI7C9X2G switches to avoid ACS
erratum with ACS P2P Request Redirect (Nathan Rossi)
* pci/virtualization:
PCI: Add ACS quirk for Pericom PI7C9X2G switches
PCI: Mark Atheros QCA6174 to avoid bus reset
- Check for CAP_SYS_ADMIN before validating sysfs user input, not after
(Krzysztof Wilczyński)
- Always return -EINVAL from sysfs "store" functions for invalid user input
instead of -EINVAL sometimes and -ERANGE others (Krzysztof Wilczyński)
- Use kstrtobool() directly instead of the strtobool() wrapper (Krzysztof
Wilczyński)
* pci/sysfs:
PCI: Use kstrtobool() directly, sans strtobool() wrapper
PCI/sysfs: Return -EINVAL consistently from "store" functions
PCI/sysfs: Check CAP_SYS_ADMIN before parsing user input
# Conflicts:
# drivers/pci/iov.c
- Return error to application when command execution fails because an
out-of-band reset has cleared the device BARs, Memory Space Enable, etc
(Kelvin Cao)
- Fix MRPC error status handling issue (Kelvin Cao)
- Mask out other bits when reading of management VEP instance ID (Kelvin
Cao)
- Return EOPNOTSUPP instead of ENOTSUPP from sysfs show functions (Kelvin
Cao)
- Add check of event support (Logan Gunthorpe)
* pci/switchtec:
PCI/switchtec: Add check of event support
PCI/switchtec: Replace ENOTSUPP with EOPNOTSUPP
PCI/switchtec: Update the way of getting management VEP instance ID
PCI/switchtec: Fix a MRPC error status handling issue
PCI/switchtec: Error out MRPC execution when MMIO reads fail
- Don't setup portdrv IRQs if there are no port drivers that use them, to
conserve vectors and avoid spurious events (Jan Kiszka)
* pci/portdrv:
PCI/portdrv: Do not setup up IRQs if there are no users
- Apply bus offset correctly in DMA address calculation, which used the
wrong sign before (Wang Lu)
* pci/p2pdma:
PCI/P2PDMA: Apply bus offset correctly in DMA address calculation
- Document sysfs "irq" attribute, which contains either the INTx IRQ (the
intended behavior) or the first MSI IRQ (historical mistake retained for
backwards compatibility) (Barry Song)
- Rework "irq" sysfs show function to explicitly fetch first MSI IRQ
instead of depending on core to put it in dev->irq, to enable future core
cleanup (Barry Song)
* pci/msi:
PCI/sysfs: Explicitly show first MSI IRQ for 'irq'
PCI: Document /sys/bus/pci/devices/.../irq
- Ignore Link Down/Up caused by error-induced Hot Reset so endpoint driver
can remain bound to device during error recovery (Lukas Wunner)
- Remove unused resume err_handler (Lukas Wunner)
- Remove unused pcie_port_bus_{,un}register() declarations (Lukas Wunner)
- Skip compiling err.c when CONFIG_PCIEAER not set (Lukas Wunner)
* pci/hotplug:
PCI/ERR: Reduce compile time for CONFIG_PCIEAER=n
PCI/portdrv: Remove unused pcie_port_bus_{,un}register() declarations
PCI/portdrv: Remove unused resume err_handler
PCI: pciehp: Ignore Link Down/Up caused by error-induced Hot Reset
PCI/portdrv: Rename pm_iter() to pcie_port_device_iter()
- Drop the struct pci_dev.driver pointer, which is redundant with the
struct device.driver pointer (Uwe Kleine-König)
* pci/driver:
PCI: Remove struct pci_dev->driver
PCI: Use to_pci_driver() instead of pci_dev->driver
x86/pci/probe_roms: Use to_pci_driver() instead of pci_dev->driver
perf/x86/intel/uncore: Use to_pci_driver() instead of pci_dev->driver
powerpc/eeh: Use to_pci_driver() instead of pci_dev->driver
usb: xhci: Use to_pci_driver() instead of pci_dev->driver
cxl: Use to_pci_driver() instead of pci_dev->driver
cxl: Factor out common dev->driver expressions
xen/pcifront: Use to_pci_driver() instead of pci_dev->driver
xen/pcifront: Drop pcifront_common_process() tests of pcidev, pdrv
nfp: use dev_driver_string() instead of pci_dev->driver->name
mlxsw: pci: Use dev_driver_string() instead of pci_dev->driver->name
net: marvell: prestera: use dev_driver_string() instead of pci_dev->driver->name
net: hns3: use dev_driver_string() instead of pci_dev->driver->name
crypto: hisilicon - use dev_driver_string() instead of pci_dev->driver->name
powerpc/eeh: Use dev_driver_string() instead of struct pci_dev->driver->name
ssb: Use dev_driver_string() instead of pci_dev->driver->name
bcma: simplify reference to driver name
crypto: qat - simplify adf_enable_aer()
scsi: message: fusion: Remove unused mpt_pci driver .probe() 'id' parameter
PCI/ERR: Factor out common dev->driver expressions
PCI: Drop pci_device_probe() test of !pci_dev->driver
PCI: Drop pci_device_remove() test of pci_dev->driver
PCI: Return NULL for to_pci_driver(NULL)
- Rename pcibios_add_device() to pcibios_device_add() since it's called
from pci_device_add() (Oliver O'Halloran)
- Don't try to enable AtomicOps on VFs, since they can only be enabled on
the PF (Selvin Xavier)
* pci/enumeration:
PCI: Do not enable AtomicOps on VFs
PCI: Rename pcibios_add_device() to pcibios_device_add()
The Pericom PI7C9X2G404/PI7C9X2G304/PI7C9X2G303 PCIe switches have an
erratum for ACS P2P Request Redirect behaviour when used in the cut-through
forwarding mode. The recommended work around for this issue is to use the
switch in store and forward mode. The erratum results in packets being
queued and not being delivered upstream, which can be observed as very poor
downstream device performance and/or dropped device-generated
data/interrupts.
Add a fixup so that when enabling or resuming the downstream port we check
if it has enabled ACS P2P Request Redirect, and if so, change the device
(via the upstream port) to use the store and forward operating mode.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=177471
Link: https://lore.kernel.org/r/20210910025823.196508-1-nathan@nathanrossi.com
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Apple PCIe controller doesn't directly feed the endpoint's Requester ID
to the IOMMU (DART), but instead maps RIDs onto Stream IDs (SIDs). The DART
and the PCIe controller must thus agree on the SIDs that are used for
translation (by using the 'iommu-map' property).
For this purpose, parse the 'iommu-map' property each time a device gets
added, and use the resulting translation to configure the PCIe RID-to-SID
mapper. Similarly, remove the translation if/when the device gets removed.
This is all driven from a bus notifier which gets registered at probe time.
Hopefully this is the only PCI controller driver in the whole system.
[bhelgaas: squash indentation from Zhaoyu Liu <zackary.liu.pro@gmail.com>:
https://lore.kernel.org/r/20211031135544.GA1616@pc]
Link: https://lore.kernel.org/r/20210929163847.2807812-10-maz@kernel.org
Tested-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
The MSI doorbell on Apple HW can be any address in the low 4GB range.
However, the MSI write is matched by the PCIe block before hitting the
iommu. It must thus be excluded from the IOVA range that is assigned to any
PCIe device.
Link: https://lore.kernel.org/r/20210929163847.2807812-9-maz@kernel.org
Tested-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Probe for the 'msi-ranges' property, and implement the MSI support in the
form of the usual two-level hierarchy.
Note that contrary to the wired interrupts, MSIs are shared among all the
ports.
Link: https://lore.kernel.org/r/20210929163847.2807812-8-maz@kernel.org
Tested-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add support for the per-port interrupt controller that deals with both INTx
signalling and management interrupts.
This allows the Link-up/Link-down interrupts to be wired, allowing the
bring-up to be synchronised (and provide debug information). The framework
can further be used to handle the rest of the per port events if and when
necessary.
Likewise, INTx signalling is implemented so that end-points can actually be
used.
Link: https://lore.kernel.org/r/20210929163847.2807812-7-maz@kernel.org
Link: https://lore.kernel.org/r/20211004150552.3844830-1-maz@kernel.org
Tested-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Now that everything is in place at the poweroff sequence, this driver can
use module_platform_driver(), which allows it to be removed.
Link: https://lore.kernel.org/r/53b40494252444a9b830827922c4e3a301b8f863.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
The logic under .remove ops is missing a call to dw_pcie_host_deinit(). Add
it, in order to allow the DWC core to be properly cleaned up.
Link: https://lore.kernel.org/r/838621e1c84ebaac153ccd9c36ea5e1254c61ead.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
The logic at kirin_pcie_gpio_request() enables some clkreq GPIO lines.
Disable them during power-off.
Link: https://lore.kernel.org/r/f403e590843de1a581cade2d534d34715706f54e.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
Instead of having two copies of the same logic, place the power-off logic
in a separate function.
No functional changes.
Link: https://lore.kernel.org/r/64f6e8da3e5fff38b6c8fcb208ace46efe6555bb.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
There's nothing preventing this driver from being loaded as a module.
Change its config from bool to tristate.
Link: https://lore.kernel.org/r/b5e7cfe9df09b492750bd6db0f0c911eaae8c2d4.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
Apple's PCIe controller requires clocks to be configured in order to
bring up the hardware. Add the register pokes required to do so.
Adapted from Corellium's driver via Mark Kettenis's U-Boot patches.
Co-developed-by: Stan Skowronek <stan@corellium.com>
Link: https://lore.kernel.org/r/20210929163847.2807812-6-maz@kernel.org
Signed-off-by: Stan Skowronek <stan@corellium.com>
Signed-off-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a minimal driver to bring up the PCIe bus on Apple system-on-chips,
particularly the Apple M1. This driver exposes the internal bus used for
the USB type-A ports, Ethernet, Wi-Fi, and Bluetooth. Bringing up the
radios requires additional drivers beyond what's necessary for PCIe itself.
Co-developed-by: Stan Skowronek <stan@corellium.com>
Link: https://lore.kernel.org/r/20210929163847.2807812-5-maz@kernel.org
Signed-off-by: Stan Skowronek <stan@corellium.com>
Signed-off-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Just as we now allow an interrupt map to be parsed when part of an
interrupt controller, there is no reason to ignore an interrupt map that
would be part of a pci device node such as a root port since we already
allow interrupt specifiers.
Allow the matching of such property when local to the node of a PCI
device, which allows the device itself to use the interrupt map for for
its own purpose.
Link: https://lore.kernel.org/r/20210929163847.2807812-4-maz@kernel.org
Tested-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Host crashes when pci_enable_atomic_ops_to_root() is called for VFs with
virtual buses. The virtual buses added to SR-IOV have bus->self set to NULL
and host crashes due to this.
PID: 4481 TASK: ffff89c6941b0000 CPU: 53 COMMAND: "bash"
...
#3 [ffff9a9481713808] oops_end at ffffffffb9025cd6
#4 [ffff9a9481713828] page_fault_oops at ffffffffb906e417
#5 [ffff9a9481713888] exc_page_fault at ffffffffb9a0ad14
#6 [ffff9a94817138b0] asm_exc_page_fault at ffffffffb9c00ace
[exception RIP: pcie_capability_read_dword+28]
RIP: ffffffffb952fd5c RSP: ffff9a9481713960 RFLAGS: 00010246
RAX: 0000000000000001 RBX: ffff89c6b1096000 RCX: 0000000000000000
RDX: ffff9a9481713990 RSI: 0000000000000024 RDI: 0000000000000000
RBP: 0000000000000080 R8: 0000000000000008 R9: ffff89c64341a2f8
R10: 0000000000000002 R11: 0000000000000000 R12: ffff89c648bab000
R13: 0000000000000000 R14: 0000000000000000 R15: ffff89c648bab0c8
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#7 [ffff9a9481713988] pci_enable_atomic_ops_to_root at ffffffffb95359a6
#8 [ffff9a94817139c0] bnxt_qplib_determine_atomics at ffffffffc08c1a33 [bnxt_re]
#9 [ffff9a94817139d0] bnxt_re_dev_init at ffffffffc08ba2d1 [bnxt_re]
Per PCIe r5.0, sec 9.3.5.10, the AtomicOp Requester Enable bit in Device
Control 2 is reserved for VFs. The PF value applies to all associated VFs.
Return -EINVAL if pci_enable_atomic_ops_to_root() is called for a VF.
Link: https://lore.kernel.org/r/1631354585-16597-1-git-send-email-selvin.xavier@broadcom.com
Fixes: 35f5ace5de ("RDMA/bnxt_re: Enable global atomic ops if platform supports")
Fixes: 430a23689d ("PCI: Add pci_enable_atomic_ops_to_root()")
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Here is the big set of driver core changes for 5.16-rc1.
All of these have been in linux-next for a while now with no reported
problems.
Included in here are:
- big update and cleanup of the sysfs abi documentation files
and scripts from Mauro. We are almost at the place where we
can properly check that the running kernel's sysfs abi is
documented fully.
- firmware loader updates
- dyndbg updates
- kernfs cleanups and fixes from Christoph
- device property updates
- component fix
- other minor driver core cleanups and fixes
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYYPbjQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ync9gCfXKMUI1GAnCfJWAwTdTcd18q5akoAoMw32/AH
0yh5TjAWFyFd7xz5d7qs
=itsC
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big set of driver core changes for 5.16-rc1.
All of these have been in linux-next for a while now with no reported
problems.
Included in here are:
- big update and cleanup of the sysfs abi documentation files and
scripts from Mauro. We are almost at the place where we can
properly check that the running kernel's sysfs abi is documented
fully.
- firmware loader updates
- dyndbg updates
- kernfs cleanups and fixes from Christoph
- device property updates
- component fix
- other minor driver core cleanups and fixes"
* tag 'driver-core-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (122 commits)
device property: Drop redundant NULL checks
x86/build: Tuck away built-in firmware under FW_LOADER
vmlinux.lds.h: wrap built-in firmware support under FW_LOADER
firmware_loader: move struct builtin_fw to the only place used
x86/microcode: Use the firmware_loader built-in API
firmware_loader: remove old DECLARE_BUILTIN_FIRMWARE()
firmware_loader: formalize built-in firmware API
component: do not leave master devres group open after bind
dyndbg: refine verbosity 1-4 summary-detail
gpiolib: acpi: Replace custom code with device_match_acpi_handle()
i2c: acpi: Replace custom function with device_match_acpi_handle()
driver core: Provide device_match_acpi_handle() helper
dyndbg: fix spurious vNpr_info change
dyndbg: no vpr-info on empty queries
dyndbg: vpr-info on remove-module complete, not starting
device property: Add missed header in fwnode.h
Documentation: dyndbg: Improve cli param examples
dyndbg: Remove support for ddebug_query param
dyndbg: make dyndbg a known cli param
dyndbg: show module in vpr-info in dd-exec-queries
...
Here is the big set of staging driver updates and cleanups for 5.16-rc1.
Overall we ended up removing a lot of code this time, a bit over 20,000
lines are now gone thanks to a lot of cleanup work by many developers.
Nothing huge in here functionality wise, just loads of cleanups:
- r8188eu driver major cleanups and removal of unused and dead
code
- wlan-ng minor cleanups
- fbtft driver cleanups
- most driver cleanups
- rtl8* drivers cleanups
- rts5208 driver cleanups
- vt6655 driver cleanups
- vc04_services drivers cleanups
- wfx cleanups on the way to almost getting this merged out of
staging (it's close!)
- tiny mips changes needed for the mt7621 drivers, they have
been acked by the respective subsystem maintainers to go
through this tree.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYYPZQQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yml9wCeJl83anYno0xh+UP6CsEkbe64VJEAoIEKyry/
tlUowcatxGfz3aYA1wTc
=FyAK
-----END PGP SIGNATURE-----
Merge tag 'staging-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here is the big set of staging driver updates and cleanups for
5.16-rc1.
Overall we ended up removing a lot of code this time, a bit over
20,000 lines are now gone thanks to a lot of cleanup work by many
developers.
Nothing huge in here functionality wise, just loads of cleanups:
- r8188eu driver major cleanups and removal of unused and dead code
- wlan-ng minor cleanups
- fbtft driver cleanups
- most driver cleanups
- rtl8* drivers cleanups
- rts5208 driver cleanups
- vt6655 driver cleanups
- vc04_services drivers cleanups
- wfx cleanups on the way to almost getting this merged out of
staging (it's close!)
- tiny mips changes needed for the mt7621 drivers, they have been
acked by the respective subsystem maintainers to go through this
tree.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (622 commits)
staging: r8188eu: hal: remove goto statement and local variable
staging: rtl8723bs: hal remove the assignment to itself
staging: rtl8723bs: fix unmet dependency on CRYPTO for CRYPTO_LIB_ARC4
staging: vchiq_core: get rid of typedef
staging: fieldbus: anybus: reframe comment to avoid warning
staging: r8188eu: fix missing unlock in rtw_resume()
staging: r8188eu: core: remove the goto from rtw_IOL_accquire_xmit_frame
staging: r8188eu: core: remove goto statement
staging: vt6655: Rename `dwAL7230InitTable` array
staging: vt6655: Rename `dwAL2230PowerTable` array
staging: vt6655: Rename `dwAL7230InitTableAMode` array
staging: vt6655: Rename `dwAL7230ChannelTable2` array
staging: vt6655: Rename `dwAL7230ChannelTable1` array
staging: vt6655: Rename `dwAL7230ChannelTable0` array
staging: vt6655: Rename `dwAL2230ChannelTable1` array
staging: vt6655: Rename `dwAL2230ChannelTable0` array
staging: r8712u: fix control-message timeout
staging: rtl8192u: fix control-message timeouts
staging: mt7621-dts: add missing SPDX license to files
staging: vchiq_core: fix quoted strings split across lines
...
We already include <linux/device.h> and <linux/msi.h>, which
include <asm/device.h> and <asm/msi.h>.
Drop the redundant includes of <asm/device.h> and <asm/msi.h>.
[bhelgaas: squash in fix from Wan Jiabing <wanjiabing@vivo.com>:
https://lore.kernel.org/r/20211104063720.29375-1-wanjiabing@vivo.com]
Link: https://lore.kernel.org/r/20211013003145.1107148-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Derrick <jonathan.derrick@linux.dev>
If an error occurs after a successful cdns_pcie_init_phy() call, it must be
undone by a cdns_pcie_disable_phy() call, as already done above and below.
Update the goto to branch at the correct place of the error handling path.
Link: https://lore.kernel.org/r/db477b0cb444891a17c4bb424467667dc30d0bab.1624794264.git.christophe.jaillet@wanadoo.fr
Fixes: 49e0efdce7 ("PCI: j721e: Add support to provide refclk to PCIe connector")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Use the preferred generic header file linux/io.h that already includes the
corresponding asm/io.h file.
Link: https://lore.kernel.org/r/20211013003145.1107148-2-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Derrick <jonathan.derrick@linux.dev>
Merge PCI device power management updates for 5.16-rc1:
- Make the association of ACPI device objects with PCI devices more
straightforward and simplify the code doing that for all devices
in general (Rafael Wysocki).
- Eliminate struct pci_platform_pm_ops and handle the both of its
users (PCI and Intel MID) directly in the PCI bus code (Rafael
Wysocki).
- Simplify and clarify ACPI PCI device PM helpers (Rafael Wysocki).
- Fix ordering of operations in pci_back_from_sleep() (Rafael
Wysocki).
* pm-pci:
PCI: PM: Fix ordering of operations in pci_back_from_sleep()
PCI: PM: Do not call platform_pci_power_manageable() unnecessarily
PCI: PM: Make pci_choose_state() call pci_target_state()
PCI: PM: Rearrange pci_target_state()
PCI: PM: Simplify acpi_pci_power_manageable()
PCI: PM: Drop struct pci_platform_pm_ops
PCI: ACPI: PM: Do not use pci_platform_pm_ops for ACPI
PCI: PM: Do not use pci_platform_pm_ops for Intel MID PM
ACPI: glue: Look for ACPI bus type only if ACPI companion is not known
ACPI: glue: Drop cleanup callback from struct acpi_bus_type
PCI: ACPI: Drop acpi_pci_bus
The PHY layer need to access APB registers too, for Kirin 970. So place
them into a named regmap.
Link: https://lore.kernel.org/r/daf0e4bda5a69a5ac8484e70f09351a959805c8c.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
The pcie-kirin driver contains both PHY and generic PCI driver.
The best would be, instead, to support a PCI PHY driver, making the driver
more generic.
However, it is too late to remove the Kirin 960 PHY, as a change like that
would make the DT schema incompatible with past versions.
So, add support for an external PHY driver without removing the existing
Kirin 960 PHY from it.
Link: https://lore.kernel.org/r/f38361df2e9d0dc5a38ff942b631f7fef64cdc12.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
The pcie-kirin PCIe driver contains internally a PHY interface for
Kirin 960.
As the next patches will add support for using an external PHY driver,
reorganize the driver in a way that the PHY part will be self-contained.
This could be moved to a separate PHY driver, but a change like that would
mean a non-backward-compatible DT schema change.
Link: https://lore.kernel.org/r/ad2f4aa6bbb71d5c9af0139704672f75f12644fc.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Add pci_find_dvsec_capability to locate a Designated Vendor-Specific
Extended Capability with the specified Vendor ID and Capability ID.
The Designated Vendor-Specific Extended Capability (DVSEC) allows one or
more "vendor" specific capabilities that are not tied to the Vendor ID
of the PCI component. Where the DVSEC Vendor may be a standards body
like CXL.
Cc: David E. Box <david.e.box@linux.intel.com>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: linux-pci@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Andrew Donnellan <ajd@linux.ibm.com>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/163379787943.692348.6814373487017444007.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Aardvark supports PCIe Hot Reset via PCIE_CORE_CTRL1_REG.
Use it for implementing PCI_BRIDGE_CTL_BUS_RESET bit of PCI_BRIDGE_CONTROL
register on emulated bridge.
With this, the function pci_reset_secondary_bus() starts working and can
reset connected PCIe card. Custom userspace script [1] which uses setpci
can trigger PCIe Hot Reset and reset the card manually.
[1] https://alexforencich.com/wiki/en/pcie/hot-reset-linux
Link: https://lore.kernel.org/r/20211028185659.20329-7-kabel@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Aardvark controller has something like config space of a Root Port
available at offset 0x0 of internal registers - these registers are used
for implementation of the emulated bridge.
The default value of Class Code of this bridge corresponds to a RAID Mass
storage controller, though. (This is probably intended for when the
controller is used as Endpoint.)
Change the Class Code to correspond to a PCI Bridge.
Add comment explaining this change.
Link: https://lore.kernel.org/r/20211028185659.20329-6-kabel@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
From very vague, ambiguous and incomplete information from Marvell we
deduced that the 32-bit Aardvark register at address 0x4
(PCIE_CORE_CMD_STATUS_REG), which is not documented for Root Complex mode
in the Functional Specification (only for Endpoint mode), controls two
16-bit PCIe registers: Command Register and Status Registers of PCIe Root
Port.
This means that bit 2 controls bus mastering and forwarding of memory and
I/O requests in the upstream direction. According to PCI specifications
bits [0:2] of Command Register, this should be by default disabled on
reset. So explicitly disable these bits at early setup of the Aardvark
driver.
Remove code which unconditionally enables all 3 bits and let kernel code
(via pci_set_master() function) to handle bus mastering of Root PCIe
Bridge via emulated PCI_COMMAND on emulated bridge.
Link: https://lore.kernel.org/r/20211028185659.20329-5-kabel@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # b2a56469d5 ("PCI: aardvark: Add FIXME comment for PCIE_CORE_CMD_STATUS_REG access")
The PCIE_MSI_PAYLOAD_REG contains 16-bit MSI number, not only lower
8 bits. Fix reading content of this register and add a comment
describing the access to this register.
Link: https://lore.kernel.org/r/20211028185659.20329-4-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
MSI domain callback .alloc() (implemented by advk_msi_irq_domain_alloc()
function) should return zero on success, since non-zero value indicates
failure.
When the driver was converted to generic MSI API in commit f21a8b1b68
("PCI: aardvark: Move to MSI handling using generic MSI support"), it
was converted so that it returns hwirq number.
Fix this.
Link: https://lore.kernel.org/r/20211028185659.20329-3-kabel@kernel.org
Fixes: f21a8b1b68 ("PCI: aardvark: Move to MSI handling using generic MSI support")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
The pci_bridge_emul_conf_write() function correctly clears W1C bits in
cfgspace cache, but it does not inform the underlying implementation
about the clear request: the .write_op() method is given the value with
these bits cleared.
This is wrong if the .write_op() needs to know which bits were requested
to be cleared.
Fix the value to be passed into the .write_op() method to have requested
W1C bits set, so that it can clear them.
Both pci-bridge-emul users (mvebu and aardvark) are compatible with this
change.
Link: https://lore.kernel.org/r/20211028185659.20329-2-kabel@kernel.org
Fixes: 23a5fba4d9 ("PCI: Introduce PCI bridge emulated config space common logic")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Cc: Russell King <rmk+kernel@armlinux.org.uk>
The bare "unsigned" type implicitly means "unsigned int", but the preferred
coding style is to use the complete type name.
Update the bare use of "unsigned" to the preferred "unsigned int".
No change to functionality intended.
See a1ce18e4f9 ("checkpatch: warn on bare unsigned or signed declarations
without int").
Link: https://lore.kernel.org/r/20211013014136.1117543-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The variable 'rc' is being initialized with a value that is never read.
Remove the redundant assignment.
Addresses-Coverity: ("Unused value")
Link: https://lore.kernel.org/r/20210910161417.91001-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Add driver for the PCIe controller of the MT7621 SoC.
[bhelgaas: rename from pci-mt7621.c to pcie-mt7621.c; also rename Kconfig
symbol from PCI_MT7621 to PCIE_MT7621]
Link: https://lore.kernel.org/r/20210922050035.18162-3-sergio.paracuellos@gmail.com
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ordering of operations in pci_back_from_sleep() is incorrect,
because the device may be in D3cold when it runs and pci_enable_wake()
needs to access the device's configuration space which cannot be
done in D3cold.
Fix this by calling pci_set_power_state() to put the device into D0
before calling pci_enable_wake() for it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Per PCIe r5.0, sec 7.5.3.16, Downstream Ports must disable LTR if the link
goes down (the Port goes DL_Down status). This is a problem because the
Downstream Port's dev->ltr_path is still set, so we think LTR is still
enabled, and we enable LTR in the Endpoint. When it sends LTR messages,
they cause Unsupported Request errors at the Downstream Port.
This happens in the reset path, where we may enable LTR in
pci_restore_pcie_state() even though the Downstream Port disabled LTR
because the reset caused a link down event.
It also happens in the hot-remove and hot-add path, where we may enable LTR
in pci_configure_ltr() even though the Downstream Port disabled LTR when
the hot-remove took the link down.
In these two scenarios, check the upstream bridge and restore its LTR
enable if appropriate.
The Unsupported Request may be logged by AER as follows:
pcieport 0000:00:1d.0: AER: Uncorrected (Non-Fatal) error received: id=00e8
pcieport 0000:00:1d.0: PCIe Bus Error: severity=Uncorrected (Non-Fatal), type=Transaction Layer, id=00e8(Requester ID)
pcieport 0000:00:1d.0: device [8086:9d18] error status/mask=00100000/00010000
pcieport 0000:00:1d.0: [20] Unsupported Request (First)
In addition, if LTR is not configured correctly, the link cannot enter the
L1.2 state, which prevents some machines from entering the S0ix low power
state.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20211012075614.54576-1-mingchuang.qiao@mediatek.com
Reported-by: Utkarsh H Patel <utkarsh.h.patel@intel.com>
Signed-off-by: Mingchuang Qiao <mingchuang.qiao@mediatek.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The sysfs "irq" file contains the legacy INTx IRQ. Or, if the device has
MSI enabled, it contains the first MSI IRQ instead.
Previously this file showed the pci_dev.irq value directly. But we'd
prefer to use pci_dev.irq only for the INTx IRQ and decouple that from any
MSI or MSI-X IRQs.
If the device has MSI enabled, explicitly look up and show the first MSI
IRQ in the sysfs "irq" file. Otherwise, show the INTx IRQ.
This removes the requirement that msi_capability_init() set pci_dev.irq to
the first MSI IRQ when enabling MSI and pci_msi_shutdown() restore the INTx
IRQ when disabling MSI.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20210825102636.52757-3-21cnbao@gmail.com
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Struct pci_driver contains a struct device_driver, so for PCI devices, it's
easy to convert a device_driver * to a pci_driver * with to_pci_driver().
The device_driver * is in struct device, so we don't need to also keep
track of the pci_driver * in struct pci_dev.
Replace pci_dev->driver with to_pci_driver(). This is a step toward
removing pci_dev->driver.
[bhelgaas: split to separate patch]
Link: https://lore.kernel.org/r/20211004125935.2300113-11-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The sole non-static function in err.c, pcie_do_recovery(), is only
called from:
* aer.c (if CONFIG_PCIEAER=y)
* dpc.c (if CONFIG_PCIE_DPC=y, which depends on CONFIG_PCIEAER)
* edr.c (if CONFIG_PCIE_EDR=y, which depends on CONFIG_PCIE_DPC)
Thus, err.c need not be compiled if CONFIG_PCIEAER=n.
Also, pci_uevent_ers() and pcie_clear_device_status(), which are called
from err.c, can be #ifdef'ed away unless CONFIG_PCIEAER=y.
Since x86_64_defconfig doesn't enable CONFIG_PCIEAER, this change may
slightly reduce compile time for anyone doing a test build with that
config.
Link: https://lore.kernel.org/r/98f9041151268c1c035ab64cca320ad86803f64a.1627638184.git.lukas@wunner.de
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit 3e41a317ae ("PCI/AER: Remove unused aer_error_resume()")
removed the resume err_handler from AER. Since no other port service
implements the callback, support for it can be removed from portdrv.
It can be revived later if need be, preferably by re-using the
pcie_port_device_iter() iterator.
Link: https://lore.kernel.org/r/25334149b604e005058aeb0fdf51e01f991d5d74.1627638184.git.lukas@wunner.de
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Keith Busch <kbusch@kernel.org>
Stuart Hayes reports that an error handled by DPC at a Root Port results
in pciehp gratuitously bringing down a subordinate hotplug port:
RP -- UP -- DP -- UP -- DP (hotplug) -- EP
pciehp brings the slot down because the Link to the Endpoint goes down.
That is caused by a Hot Reset being propagated as a result of DPC.
Per PCIe Base Spec 5.0, section 6.6.1 "Conventional Reset":
For a Switch, the following must cause a hot reset to be sent on all
Downstream Ports: [...]
* The Data Link Layer of the Upstream Port reporting DL_Down status.
In Switches that support Link speeds greater than 5.0 GT/s, the
Upstream Port must direct the LTSSM of each Downstream Port to the
Hot Reset state, but not hold the LTSSMs in that state. This permits
each Downstream Port to begin Link training immediately after its
hot reset completes. This behavior is recommended for all Switches.
* Receiving a hot reset on the Upstream Port.
Once DPC recovers, pcie_do_recovery() walks down the hierarchy and
invokes pcie_portdrv_slot_reset() to restore each port's config space.
At that point, a hotplug interrupt is signaled per PCIe Base Spec r5.0,
section 6.7.3.4 "Software Notification of Hot-Plug Events":
If the Port is enabled for edge-triggered interrupt signaling using
MSI or MSI-X, an interrupt message must be sent every time the logical
AND of the following conditions transitions from FALSE to TRUE: [...]
* The Hot-Plug Interrupt Enable bit in the Slot Control register is
set to 1b.
* At least one hot-plug event status bit in the Slot Status register
and its associated enable bit in the Slot Control register are both
set to 1b.
Prevent pciehp from gratuitously bringing down the slot by clearing the
error-induced Data Link Layer State Changed event before restoring
config space. Afterwards, check whether the link has unexpectedly
failed to retrain and synthesize a DLLSC event if so.
Allow each pcie_port_service_driver (one of them being pciehp) to define
a slot_reset callback and re-use the existing pm_iter() function to
iterate over the callbacks.
Thereby, the Endpoint driver remains bound throughout error recovery and
may restore the device to working state.
Surprise removal during error recovery is detected through a Presence
Detect Changed event. The hotplug port is expected to not signal that
event as a result of a Hot Reset.
The issue isn't DPC-specific, it also occurs when an error is handled by
AER through aer_root_reset(). So while the issue was noticed only now,
it's been around since 2006 when AER support was first introduced.
[bhelgaas: drop PCI_ERROR_RECOVERY Kconfig, split pm_iter() rename to
preparatory patch]
Link: https://lore.kernel.org/linux-pci/08c046b0-c9f2-3489-eeef-7e7aca435bb9@gmail.com/
Fixes: 6c2b374d74 ("PCI-Express AER implemetation: AER core and aerdriver")
Link: https://lore.kernel.org/r/251f4edcc04c14f873ff1c967bc686169cd07d2d.1627638184.git.lukas@wunner.de
Reported-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Tested-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v2.6.19+: ba952824e6: PCI/portdrv: Report reset for frozen channel
Cc: Keith Busch <kbusch@kernel.org>
Struct pci_driver contains a struct device_driver, so for PCI devices, it's
easy to convert a device_driver * to a pci_driver * with to_pci_driver().
The device_driver * is in struct device, so we don't need to also keep
track of the pci_driver * in struct pci_dev.
Replace pdev->driver with to_pci_driver(). This is a step toward removing
pci_dev->driver.
[bhelgaas: split to separate patch]
Link: https://lore.kernel.org/r/20211004125935.2300113-11-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
pcifront_common_process() exits early if pcidev or pcidev->driver are NULL,
so simplify it by not checking them again.
[bhelgaas: split flag change to separate patch]
Link: https://lore.kernel.org/r/20211004125935.2300113-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The condition register PCI_RCV_INTX is used in irq_mask() and irq_unmask()
callbacks. Accesses to register can occur at the same time without a lock.
Add a lock into each callback to prevent the issue.
And INTX mask and unmask fields in PCL_RCV_INTX register should only be
set/reset for each bit. Clearing by PCL_RCV_INTX_ALL_MASK should be
removed.
INTX status fields in PCL_RCV_INTX register only indicates each INTX
interrupt status, so the handler can't clear by writing 1 to the field.
The status is expected to be cleared by the interrupt origin.
The ack function has no meaning, so should remove it.
Suggested-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/1631924579-24567-1-git-send-email-hayashi.kunihiko@socionext.com
Fixes: 7e6d5cd88a ("PCI: uniphier: Add UniPhier PCIe host controller support")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
On the SC7280, the clock source for gcc_pcie_1_pipe_clk_src must be the
TCXO while gdsc is enabled. After PHY init successful clock source should
switch to pipe clock for gcc_pcie_1_pipe_clk_src.
Link: https://lore.kernel.org/r/1633628923-25047-6-git-send-email-pmaliset@codeaurora.org
Signed-off-by: Prasad Malisetty <pmaliset@codeaurora.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Add struct qcom_pcie_cfg as match data for all platforms. Assign
appropriate platform ops into struct qcom_pcie_cfg and read using
of_device_get_match_data() in qcom_pcie_probe().
Link: https://lore.kernel.org/r/1633628923-25047-5-git-send-email-pmaliset@codeaurora.org
Signed-off-by: Prasad Malisetty <pmaliset@codeaurora.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Not all events are supported by every gen/variant of the Switchtec
firmware. To solve this, since Gen4, a new bit in each event header
is introduced to indicate if an event is supported by the firmware.
Link: https://lore.kernel.org/r/20211014141859.11444-6-kelvin.cao@microchip.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ENOTSUPP is not a SUSV4 error code, and the following checkpatch.pl
warning will be given for new patches which still use ENOTSUPP.
WARNING: ENOTSUPP is not a SUSV4 error code, prefer EOPNOTSUPP
See the link below for the discussion.
https://lore.kernel.org/netdev/20200511165319.2251678-1-kuba@kernel.org/
Replace ENOTSUPP with EOPNOTSUPP to align with future patches which will
be using EOPNOTSUPP.
Link: https://lore.kernel.org/r/20211014141859.11444-5-kelvin.cao@microchip.com
Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Gen4 firmware adds DMA VEP and NVMe VEP support in VEP (virtual EP)
instance ID register in addtion to management EP, update the way of
getting management VEP instance ID.
Link: https://lore.kernel.org/r/20211014141859.11444-4-kelvin.cao@microchip.com
Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If an error is encountered when executing a MRPC command, the firmware
will set the status register to SWITCHTEC_MRPC_STATUS_ERROR and return
the error code in the return value register.
Add handling of SWITCHTEC_MRPC_STATUS_ERROR on status register when
completing a MRPC command.
Link: https://lore.kernel.org/r/20211014141859.11444-3-kelvin.cao@microchip.com
Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
A firmware hard reset may be initiated by various mechanisms including a
UART interface, TWI sideband interface from BMC, MRPC command from
userspace, etc. The switchtec management driver is unaware of these
resets.
The reset clears PCI state including the BARs and Memory Space Enable
bits, so the device no longer responds to the MMIO accesses the driver
uses to operate it.
MMIO reads to the device will fail with a PCIe error. When the root
complex handles that error, it typically fabricates ~0 data to complete
the CPU read.
Check for this sort of error by reading the device ID from MMIO space.
This ID can never be ~0, so if we see that value, it probably means the
PCIe Memory Read failed and we should return an error indication to the
application using the switchtec driver.
Link: https://lore.kernel.org/r/20211014141859.11444-2-kelvin.cao@microchip.com
Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
With UML having enabled (simulated) PCI on UML, VMD breaks
allyesconfig/allmodconfig compilation because it assumes
it's running on X86_64 bare metal, and has hardcoded API
use of ARCH=x86. Make it depend on !UML to fix this.
Link: https://lore.kernel.org/r/20210811162530.affe26231bc3.I131b3c1e67e3d2ead6e98addd256c835fbef9a3e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
The code block related to the if-statement in cpqhp_set_irq() is
somewhat awkwardly formatted making the code hard to read.
Make it readable. No change to functionality intended.
Link: https://lore.kernel.org/r/20211013011412.1110829-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously, when msi_populate_sysfs() failed, we saved the error return
value as dev->msi_irq_groups, which leads to a page fault when
free_msi_irqs() calls msi_destroy_sysfs().
To prevent this, leave dev->msi_irq_groups alone when msi_populate_sysfs()
fails.
Found by the Hulk Robot when injecting a memory allocation fault in
msi_populate_sysfs():
BUG: unable to handle page fault for address: fffffffffffffff4
...
Call Trace:
msi_destroy_sysfs+0x30/0xa0
free_msi_irqs+0x11d/0x1b0
Fixes: 2f170814bd ("genirq/msi: Move MSI sysfs handling from PCI to MSI core")
Link: https://lore.kernel.org/r/20211012071556.939137-1-wanghai38@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Barry Song <song.bao.hua@hisilicon.com>
Save the struct pci_driver pointer from pdev->driver instead of repeating
it several times. No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When the device core calls the .probe() callback for a device, the device
is never bound, so pci_dev->driver is always NULL.
Remove the unnecessary test of !pci_dev->driver.
Link: https://lore.kernel.org/r/20211004125935.2300113-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
When the driver core calls pci_device_remove(), there is a driver bound
to the device, so pci_dev->driver is never NULL.
Remove the unnecessary test of pci_dev->driver.
Link: https://lore.kernel.org/r/20211004125935.2300113-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cppcheck warns that pci_dev_str_match_path() passes pointers to signed ints
to sscanf("%x"), which expects pointers to *unsigned* ints:
invalidScanfArgType_int drivers/pci/pci.c:312 %x in format string (no. 2) requires 'unsigned int *' but the argument type is 'signed int *'.
Declare the variables as unsigned to avoid this issue.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20211008222732.2868493-3-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
"dom_req" is a u16 but varargs automatically promotes it to int, so there's
no point in using the %h modifier. Drop it.
See cbacb5ab0a ("docs: printk-formats: Stop encouraging use of
unnecessary %h[xudi] and %hh[xudi]") and 70eb2275ff ("checkpatch: add
warning for unnecessary use of %h[xudi] and %hh[xudi]").
Link: https://lore.kernel.org/r/20211008222732.2868493-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When enabling VMD in BIOS setup (Ice Lake Processor: Whitley platform),
the host OS cannot boot successfully with the following error message:
nvme nvme0: I/O 12 QID 0 timeout, completion polled
nvme nvme0: Shutdown timeout set to 6 seconds
DMAR: DRHD: handling fault status reg 2
DMAR: [INTR-REMAP] Request device [0x00:0x00.5] fault index 0xa00 [fault reason 0x25] Blocked a compatibility format interrupt request
The request device is the VMD controller:
# lspci -s 0000:00.5 -nn
0000:00:00.5 RAID bus controller [0104]: Intel Corporation Volume
Management Device NVMe RAID Controller [8086:28c0] (rev 04)
`git bisect` points to this offending commit ee81ee84f8 ("PCI:
vmd: Disable MSI-X remapping when possible"), which disables VMD MSI
remapping. The IOMMU hardware blocks the compatibility format
interrupt request because Interrupt Remapping Enable Status (IRES) and
Extended Interrupt Mode Enable (EIME) are enabled. Please refer to
section "5.1.4 Interrupt-Remapping Hardware Operation" in Intel VT-d
spec.
To fix the issue, VMD driver still enables the interrupt remapping
irrespective of VMD_FEAT_CAN_BYPASS_MSI_REMAP if the IOMMU subsystem
enables the interrupt remapping.
Test configuration is shown as follows:
* Two VMD controllers
1. 8086:28c0 (Whitley's VMD)
2. 8086:201d (Purley's VMD: The issue does not appear in this
controller. Just make sure if any side effect occurs.)
* w/wo intremap=off
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=214219
Link: https://lore.kernel.org/r/20210901124047.1615-1-adrianhuang0701@gmail.com
Signed-off-by: Adrian Huang <ahuang12@lenovo.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Cc: Jon Derrick <jonathan.derrick@intel.com>
Cc: Nirmal Patel <nirmal.patel@linux.intel.com>
Cc: Joerg Roedel <jroedel@suse.de>
On the Qualcomm sc8180x platform the bootloader does something related
to PCI that leaves a pending "msi" interrupt, which with the current
ordering often fires before init has a chance to enable the clocks that
are necessary for the interrupt handler to access the hardware.
Move the host_init() call before the registration of the "msi" interrupt
handler to ensure the host driver has a chance to enable the clocks.
The assignment of the bridge's ops and child_ops is moved along, because
at least the TI Keystone driver overwrites these in its host_init
callback.
Link: https://lore.kernel.org/r/20210823154958.305677-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Add driver for Qualcomm PCIe Endpoint controller based on the DesignWare
core with added Qualcomm-specific wrapper around the core. The driver
support is very basic such that it supports only enumeration, PCIe
read/write, and MSI. There is no ASPM and PM support for now but these will
be added later.
The driver is capable of using the PERST# and WAKE# side-band GPIOs for
operation and written on top of the DWC PCI framework.
[bhelgaas: wrap a few long lines]
Co-developed-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
[mani: restructured the driver and fixed several bugs for upstream]
Link: https://lore.kernel.org/r/20210920065946.15090-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
In certain cases we need a variant of pci_read_vpd()/pci_write_vpd() that
does not check against dev->vpd.len. Such cases are:
- Reading VPD if dev->vpd.len isn't set yet (in pci_vpd_size())
- Devices that map non-VPD information to arbitrary places in VPD address
space (example: Chelsio T3 EEPROM write-protect flag)
Therefore add pci_read_vpd_any() and pci_write_vpd_any() that check against
PCI_VPD_MAX_SIZE only.
Link: https://lore.kernel.org/r/93ecce28-a158-f02a-d134-8afcaced8efe@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
- Fix potential memory leak on a error path in eBPF.
- Fix handling of zpci device on reserve.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAmFg0FoACgkQjYWKoQLX
FBg3jgf8DLCs6JwK8GOz40CuZsajARwuagZy0udc3GbcZVNUog6GP7hJBU6q8pkm
JQMTl1C7Pe81p/aTOx2IIplV+owAVRnwdNBmj/psmZrI5P0CvLtTc4gVuCZJHJy4
9qt83KocgrN4G2K7qZDfiEAv+Ae/F7r20K5ZBX0exZBkOFeXZzUYVwWxM3pV45XB
Zx5AWmpHGGZFaS3EKW7E5VqswlGYIfUzGaXezN/cIl5HzMqqQMYo77eCJAWr//1z
s2s+vvEUBLGuHS8pDdXq8qR7Fq93cJSS7eo5zLVgtyZHr3Nn3+IlA0WKmPU3SmPE
+19I3L5hR0Ap6xh4ASgxciexnXFttQ==
=bGB2
-----END PGP SIGNATURE-----
Merge tag 's390-5.15-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Vasily Gorbik:
- Fix potential memory leak on a error path in eBPF
- Fix handling of zpci device on reserve
* tag 's390-5.15-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pci: fix zpci_zdev_put() on reserve
bpf, s390: Fix potential memory leak about jit_data
Correct a number of misspelled words and remove any words that were
duplicated in the PCI tree. No change to functionality intended.
Link: https://lore.kernel.org/r/20211006233827.147328-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Fix a recent ACPI-related regression in the PCI subsystem that
introduced a NULL pointer dereference possible to trigger from
user space via sysfs on some systems.
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEE4fcc61cGeeHD/fCwgsRv/nhiVHEFAmFgfJoSHHJqd0Byand5
c29ja2kubmV0AAoJEILEb/54YlRxJv4QAIdPK7ZRujQYf3EF0n+4nVwLRt0wzrZq
O33t4DS+CUdFKail3LKb++ZmuhQWoMD40f7FkDyuCKH3CVZsI96H7Fs4/6pfjrHj
y78UcDAJQ28KaJHsDSO1mQv8qcrDj5pn1renzCeWOZG9jxO+oPsXfoVb7s+nG1As
2WL3vgsVe3APp/IIQKy2eVNb/RsHFHHW+cYV4tFzTOwGKwzF4QAJAM8VQ+F+bLle
ixOmNdtOY3ttcNFvj0k/wtqbYOlTjXrwQnmGUj9PEgzBmrpp+kqnKCtHxzZnTXRL
lRaDtIeDipGwVBUOzkfGCGKvNiHnLTipdBlXvjG48fOrYLPawRhYjDH3kquMWVKl
c8hjITmfJ8z9u0fJ5UcT1MEWjHRzyF0/+kUymvT076LIom+/W27uKmvLzMojotrL
lWqvWwUwWhyKHPzv7rhMIfyHrfUWEltfhB15EdFSV14dwukMfXgHJFkk3TrA8Mjn
m3ft3/RhmJsbJVhJR4VpHMCkGvidi0XtjgS5IKpBYJS6Hzp9WgSO1vXkLQUd8YwS
dKvMTzoDN+zYx2UDm5sPbUTIGcHr4aCZ2kZqo/gnEPyGkhNYHSOjklKuVnPeaZoY
fEQxIWmtLZs/77jFEkUbMVrJaigsWeAHqPCCjmia4BZQMlOzefxBuwpTJX2zMi3y
pkAlAU55ugtv
=H0kg
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Fix a recent ACPI-related regression in the PCI subsystem that
introduced a NULL pointer dereference possible to trigger from
user space via sysfs on some systems"
* tag 'acpi-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PCI: ACPI: Check parent pointer in acpi_pci_find_companion()
Remove includes that are not needed, to speed up (re)compilation.
Most of these are relics from splitting the driver in a host and a
common part.
[bhelgaas: use driver tag analogous to rcar-ep]
Link: https://lore.kernel.org/r/54bed9a0e6991490ddb2b07e5abfaf40a7a62928.1633090577.git.geert+renesas@glider.be
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Remove includes that are not needed, to speed up (re)compilation. Include
<linux/pm_runtime.h>, which is needed, and was included implicitly through
<linux/phy/phy.h> before.
Most of these are relics from splitting the driver in a host and a common
part and adding endpoint support.
[bhelgaas: use driver tag consistent with cadence-ep, designware-ep]
Link: https://lore.kernel.org/r/7c708841a2bf84f85b14a963271c3e99c8ba38a5.1633090444.git.geert+renesas@glider.be
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEIbPD0id6easf0xsudhRwX5BBoF4FAmFeykwTHHdlaS5saXVA
a2VybmVsLm9yZwAKCRB2FHBfkEGgXhRLCADXOOSGKk4L1vWssRRhLmMXI45ElocY
EbZ/mXcQhxKnlVhdMNnupGjz+lU5FQGkCCWlhmt9Ml2O6R+lDx+zIUS8BK3Nkom9
twWjueMtum6yFwDMGYALhptVLjDqVFG71QcW0incghpnAx4s2FVE8h38md5MuUFY
Kqqf/dRkppSePldHFrRG/e4c6r0WyTsJ6Z9LTU0UYp5GqJcmUJlx7TxxqzGk5Fti
GpQ5cFS7JX8xHAkRROk/dvwJte1RRnBAW6lIWxwAaDJ6Gbg7mNfOQe7n+/KRO7ZG
gC5hbkP9tMv2nthLxaFbpu791U4lMZ2WiTLZvbgCseO3FCmToXWZ6TDd
=1mdq
-----END PGP SIGNATURE-----
Merge tag 'hyperv-fixes-signed-20211007' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv fixes from Wei Liu:
- Replace uuid.h with types.h in a header (Andy Shevchenko)
- Avoid sleeping in atomic context in PCI driver (Long Li)
- Avoid sending IPI to self when it shouldn't (Vitaly Kuznetsov)
* tag 'hyperv-fixes-signed-20211007' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
x86/hyperv: Avoid erroneously sending IPI to 'self'
hyper-v: Replace uuid.h with types.h
PCI: hv: Fix sleep while in non-sleep context when removing child devices from the bus
If acpi_pci_find_companion() is called for a device whose parent
pointer is NULL, it will crash when attempting to get the ACPI
companion of the parent due to a NULL pointer dereference in
the ACPI_COMPANION() macro.
This was not a problem before commit 375553a932 ("PCI: Setup ACPI
fwnode early and at the same time with OF") that made pci_setup_device()
call pci_set_acpi_fwnode() and so it allowed devices with NULL parent
pointers to be passed to acpi_pci_find_companion() which is the case
in pci_iov_add_virtfn(), for instance.
Fix this issue by making acpi_pci_find_companion() check the device's
parent pointer upfront and bail out if it is NULL.
While pci_iov_add_virtfn() can be changed to set the device's parent
pointer before calling pci_setup_device() for it, checking pointers
against NULL before dereferencing them is prudent anyway and looking
for ACPI companions of virtual functions isn't really useful.
Fixes: 375553a932 ("PCI: Setup ACPI fwnode early and at the same time with OF")
Link: https://lore.kernel.org/linux-acpi/8e4bbd5c59de31db71f718556654c0aa077df03d.camel@linux.ibm.com/
Reported-by: Niklas Schnelle <schnelle@linux.ibm.com>
Tested-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
If the system has multiple VMD controllers, the driver does not assign
a number to each controller, so when analyzing the interrupt through
/proc/interrupts, the names of all controllers are the same, which is
not very convenient for problem analysis. Here, try to assign a number
to each VMD controller.
Link: https://lore.kernel.org/r/1631884404-24141-1-git-send-email-brookxu.cn@gmail.com
Signed-off-by: Chunguang Xu <brookxu@tencent.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
The "depends on" Kconfig construct is a no-op in options that
are selected and therefore has no effect. Remove it.
Clean up the users of PCIE_DW_EP and introduce idiom
depends on PCI_ENDPOINT
select PCIE_DW_EP
for all of them.
Link: https://lore.kernel.org/r/20210623140103.47818-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The "depends on" Kconfig construct is a no-op in options that
are selected and therefore has no effect. Remove it.
Furthermore, there is no need to repeat menu dependencies (PCI).
Clean up the users of PCIE_DW_HOST and introduce idiom
depends on PCI_MSI_IRQ_DOMAIN
select PCIE_DW_HOST
for all of them.
Link: https://lore.kernel.org/r/20210623140103.47818-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add support for reporting PCI_EXP_LNKSTA_DLLLA bit in Link Control register
on emulated bridge via current LTSSM state. Also correctly indicate DLLLA
capability via PCI_EXP_LNKCAP_DLLLARC bit in Link Control Capability
register.
Link: https://lore.kernel.org/r/20211005180952.6812-14-kabel@kernel.org
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Current implementation of advk_pcie_link_up() is wrong as it marks also
link disabled or hot reset states as link up.
Fix it by marking link up only to those states which are defined in PCIe
Base specification 3.0, Table 4-14: Link Status Mapped to the LTSSM.
To simplify implementation, Define macros for every LTSSM state which
aardvark hardware can return in CFG_REG register.
Fix also checking for link training according to the same Table 4-14.
Define a new function advk_pcie_link_training() for this purpose.
Link: https://lore.kernel.org/r/20211005180952.6812-13-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Cc: Remi Pommarel <repk@triplefau.lt>
Fix multiple link training issues in aardvark driver. The main reason of
these issues was misunderstanding of what certain registers do, since their
names and comments were misleading: before commit 96be36dbff ("PCI:
aardvark: Replace custom macros by standard linux/pci_regs.h macros"), the
pci-aardvark.c driver used custom macros for accessing standard PCIe Root
Bridge registers, and misleading comments did not help to understand what
the code was really doing.
After doing more tests and experiments I've come to the conclusion that the
SPEED_GEN register in aardvark sets the PCIe revision / generation
compliance and forces maximal link speed. Both GEN3 and GEN2 values set the
read-only PCI_EXP_FLAGS_VERS bits (PCIe capabilities version of Root
Bridge) to value 2, while GEN1 value sets PCI_EXP_FLAGS_VERS to 1, which
matches with PCI Express specifications revisions 3, 2 and 1 respectively.
Changing SPEED_GEN also sets the read-only bits PCI_EXP_LNKCAP_SLS and
PCI_EXP_LNKCAP2_SLS to corresponding speed.
(Note that PCI Express rev 1 specification does not define PCI_EXP_LNKCAP2
and PCI_EXP_LNKCTL2 registers and when SPEED_GEN is set to GEN1 (which
also sets PCI_EXP_FLAGS_VERS set to 1), lspci cannot access
PCI_EXP_LNKCAP2 and PCI_EXP_LNKCTL2 registers.)
Changing PCIe link speed can be done via PCI_EXP_LNKCTL2_TLS bits of
PCI_EXP_LNKCTL2 register. Armada 3700 Functional Specifications says that
the default value of PCI_EXP_LNKCTL2_TLS is based on SPEED_GEN value, but
tests showed that the default value is always 8.0 GT/s, independently of
speed set by SPEED_GEN. So after setting SPEED_GEN, we must also set value
in PCI_EXP_LNKCTL2 register via PCI_EXP_LNKCTL2_TLS bits.
Triggering PCI_EXP_LNKCTL_RL bit immediately after setting LINK_TRAINING_EN
bit actually doesn't do anything. Tests have shown that a delay is needed
after enabling LINK_TRAINING_EN bit. As triggering PCI_EXP_LNKCTL_RL
currently does nothing, remove it.
Commit 43fc679ced ("PCI: aardvark: Improve link training") introduced
code which sets SPEED_GEN register based on negotiated link speed from
PCI_EXP_LNKSTA_CLS bits of PCI_EXP_LNKSTA register. This code was added to
fix detection of Compex WLE900VX (Atheros QCA9880) WiFi GEN1 PCIe cards, as
otherwise these cards were "invisible" on PCIe bus (probably because they
crashed). But apparently more people reported the same issues with these
cards also with other PCIe controllers [1] and I was able to reproduce this
issue also with other "noname" WiFi cards based on Atheros QCA9890 chip
(with the same PCI vendor/device ids as Atheros QCA9880). So this is not an
issue in aardvark but rather an issue in Atheros QCA98xx chips. Also, this
issue only exists if the kernel is compiled with PCIe ASPM support, and a
generic workaround for this is to change PCIe Bridge to 2.5 GT/s link speed
via PCI_EXP_LNKCTL2_TLS_2_5GT bits in PCI_EXP_LNKCTL2 register [2], before
triggering PCI_EXP_LNKCTL_RL bit. This workaround also works when SPEED_GEN
is set to value GEN2 (5 GT/s). So remove this hack completely in the
aardvark driver and always set SPEED_GEN to value from 'max-link-speed' DT
property. Fix for Atheros QCA98xx chips is handled separately by patch [2].
These two things (code for triggering PCI_EXP_LNKCTL_RL bit and changing
SPEED_GEN value) also explain why commit 6964494582 ("PCI: aardvark:
Train link immediately after enabling training") somehow fixed detection of
those problematic Compex cards with Atheros chips: if triggering link
retraining (via PCI_EXP_LNKCTL_RL bit) was done immediately after enabling
link training (via LINK_TRAINING_EN), it did nothing. If there was a
specific delay, aardvark HW already initialized PCIe link and therefore
triggering link retraining caused the above issue. Compex cards triggered
link down event and disappeared from the PCIe bus.
Commit f4c7d053d7 ("PCI: aardvark: Wait for endpoint to be ready before
training link") added 100ms sleep before calling 'Start link training'
command and explained that it is a requirement of PCI Express
specification. But the code after this 100ms sleep was not doing 'Start
link training', rather it triggered PCI_EXP_LNKCTL_RL bit via PCIe Root
Bridge to put link into Recovery state.
The required delay after fundamental reset is already done in function
advk_pcie_wait_for_link() which also checks whether PCIe link is up.
So after removing the code which triggers PCI_EXP_LNKCTL_RL bit on PCIe
Root Bridge, there is no need to wait 100ms again. Remove the extra
msleep() call and update comment about the delay required by the PCI
Express specification.
According to Marvell Armada 3700 Functional Specifications, Link training
should be enabled via aardvark register LINK_TRAINING_EN after selecting
PCIe generation and x1 lane. There is no need to disable it prior resetting
card via PERST# signal. This disabling code was introduced in commit
5169a9851d ("PCI: aardvark: Issue PERST via GPIO") as a workaround for
some Atheros cards. It turns out that this also is Atheros specific issue
and affects any PCIe controller, not only aardvark. Moreover this Atheros
issue was triggered by juggling with PCI_EXP_LNKCTL_RL, LINK_TRAINING_EN
and SPEED_GEN bits interleaved with sleeps. Now, after removing triggering
PCI_EXP_LNKCTL_RL, there is no need to explicitly disable LINK_TRAINING_EN
bit. So remove this code too. The problematic Compex cards described in
previous git commits are correctly detected in advk_pcie_train_link()
function even after applying all these changes.
Note that with this patch, and also prior this patch, some NVMe disks which
support PCIe GEN3 with 8 GT/s speed are negotiated only at the lowest link
speed 2.5 GT/s, independently of SPEED_GEN value. After manually triggering
PCI_EXP_LNKCTL_RL bit (e.g. from userspace via setpci), these NVMe disks
change link speed to 5 GT/s when SPEED_GEN was configured to GEN2. This
issue first needs to be properly investigated. I will send a fix in the
future.
On the other hand, some other GEN2 PCIe cards with 5 GT/s speed are
autonomously by HW autonegotiated at full 5 GT/s speed without need of any
software interaction.
Armada 3700 Functional Specifications describes the following steps for
link training: set SPEED_GEN to GEN2, enable LINK_TRAINING_EN, poll until
link training is complete, trigger PCI_EXP_LNKCTL_RL, poll until signal
rate is 5 GT/s, poll until link training is complete, enable ASPM L0s.
The requirement for triggering PCI_EXP_LNKCTL_RL can be explained by the
need to achieve 5 GT/s speed (as changing link speed is done by throw to
recovery state entered by PCI_EXP_LNKCTL_RL) or maybe as a part of enabling
ASPM L0s (but in this case ASPM L0s should have been enabled prior
PCI_EXP_LNKCTL_RL).
It is unknown why the original pci-aardvark.c driver was triggering
PCI_EXP_LNKCTL_RL bit before waiting for the link to be up. This does not
align with neither PCIe base specifications nor with Armada 3700 Functional
Specification. (Note that in older versions of aardvark, this bit was
called incorrectly PCIE_CORE_LINK_TRAINING, so this may be the reason.)
It is also unknown why Armada 3700 Functional Specification says that it is
needed to trigger PCI_EXP_LNKCTL_RL for GEN2 mode, as according to PCIe
base specification 5 GT/s speed negotiation is supposed to be entirely
autonomous, even if initial speed is 2.5 GT/s.
[1] - https://lore.kernel.org/linux-pci/87h7l8axqp.fsf@toke.dk/
[2] - https://lore.kernel.org/linux-pci/20210326124326.21163-1-pali@kernel.org/
Link: https://lore.kernel.org/r/20211005180952.6812-12-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
PCIe config space can be initialized also before pci_bridge_emul_init()
call, so move rootcap initialization after PCI config space initialization.
This simplifies the function a little since it removes one if (ret < 0)
check.
Link: https://lore.kernel.org/r/20211005180952.6812-11-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Commit 43f5c77bcb ("PCI: aardvark: Fix reporting CRS value") fixed
handling of CRS response and when CRSSVE flag was not enabled it marked CRS
response as failed transaction (due to simplicity).
But pci-aardvark.c driver is already waiting up to the PIO_RETRY_CNT count
for PIO config response and so we can with a small change implement
re-issuing of config requests as described in PCIe base specification.
This change implements re-issuing of config requests when response is CRS.
Set upper bound of wait cycles to around PIO_RETRY_CNT, afterwards the
transaction is marked as failed and an all-ones value is returned as
before.
We do this by returning appropriate error codes from function
advk_pcie_check_pio_status(). On CRS we return -EAGAIN and caller then
reissues transaction.
Link: https://lore.kernel.org/r/20211005180952.6812-10-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Avoid code repetition in advk_pcie_rd_conf() by handling errors with
goto jump, as is customary in kernel.
Link: https://lore.kernel.org/r/20211005180952.6812-9-kabel@kernel.org
Fixes: 43f5c77bcb ("PCI: aardvark: Fix reporting CRS value")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
There are lot of undocumented interrupt bits. To prevent unwanted
spurious interrupts, fix all *_ALL_MASK macros to define all interrupt
bits, so that driver can properly mask all interrupts, including those
which are undocumented.
Link: https://lore.kernel.org/r/20211005180952.6812-8-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
The PCIE_ISR1_REG says which interrupts are currently set / active,
including those which are masked.
The driver currently reads this register and looks if some unmasked
interrupts are active, and if not, it clears status bits of _all_
interrupts, including the masked ones.
This is incorrect, since, for example, some drivers may poll these bits.
Remove this clearing, and also remove this early return statement
completely, since it does not change functionality in any way.
Link: https://lore.kernel.org/r/20211005180952.6812-7-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Commit 366697018c ("PCI: aardvark: Add PHY support") introduced
configuration of PCIe Reference clock via PCIE_CORE_REF_CLK_REG register,
but did it incorrectly.
PCIe Reference clock differential pair is routed from system board to
endpoint card, so on CPU side it has output direction. Therefore it is
required to enable transmitting and disable receiving.
Default configuration according to Armada 3700 Functional Specifications is
enabled receiver part and disabled transmitter.
We need this change because otherwise PCIe Reference clock is configured to
some undefined state when differential pair is used for both transmitting
and receiving.
Fix this by disabling receiver part.
Link: https://lore.kernel.org/r/20211005180952.6812-6-kabel@kernel.org
Fixes: 366697018c ("PCI: aardvark: Add PHY support")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Commit 43f5c77bcb ("PCI: aardvark: Fix reporting CRS value") started
using CRSSVE flag for handling CRS responses.
PCI_EXP_RTCTL_CRSSVE flag is stored only in emulated config space buffer
and there is handler for PCI_EXP_RTCTL register. So every read operation
from config space automatically clears CRSSVE flag as it is not defined in
PCI_EXP_RTCTL read handler.
Fix this by reading current CRSSVE bit flag from emulated space buffer and
appending it to PCI_EXP_RTCTL read response.
Link: https://lore.kernel.org/r/20211005180952.6812-5-kabel@kernel.org
Fixes: 43f5c77bcb ("PCI: aardvark: Fix reporting CRS value")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Use dev_dbg() instead of dev_err() in advk_pcie_check_pio_status().
For example CRS is not an error status, it just says that the request
should be retried.
Link: https://lore.kernel.org/r/20211005180952.6812-4-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Change PCIe Max Payload Size setting in PCIe Device Control register to 512
bytes to align with PCIe Link Initialization sequence as defined in Marvell
Armada 3700 Functional Specification. According to the specification,
maximal Max Payload Size supported by this device is 512 bytes.
Without this kernel prints suspicious line:
pci 0000:01:00.0: Upstream bridge's Max Payload Size set to 256 (was 16384, max 512)
With this change it changes to:
pci 0000:01:00.0: Upstream bridge's Max Payload Size set to 256 (was 512, max 512)
Link: https://lore.kernel.org/r/20211005180952.6812-3-kabel@kernel.org
Fixes: 8c39d71036 ("PCI: aardvark: Add Aardvark PCI host controller driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Use the proper macro instead of hard-coded (-1) value.
Suggested-by: Krzysztof Wilczyński <kw@linux.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Link: https://lore.kernel.org/r/20211004133453.18881-2-mgurtovoy@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop two invocations of platform_pci_power_manageable() that are not
necessary, because the functions called when it returns 'true' do the
requisite "power manageable" checks themselves.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
The pci_choose_state() and pci_target_state() implementations are
somewhat divergent without a good reason, because they are used
for similar purposes.
Change the pci_choose_state() implementation to use pci_target_state()
internally except for transitions to the working state of the system
in which case it is expected to return D0.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
Make pci_target_state() return D3cold or D0 without checking PME
support if the current power state of the device is D3cold or if it
does not support the standard PCI PM, respectively.
Next, drop the tergat_state local variable that has become redundant
from it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
Make acpi_pci_power_manageable() more straightforward.
No functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
After previous changes there are no more users of struct
pci_platform_pm_ops in the tree, so drop it along with all of the
remaining related code.
No functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
pci_remap_iospace() was originally meant as an architecture specific helper
but it moved into generic code after all architectures had the same
requirements. MIPS has different requirements so it should not be shared.
The way for doing this will be using a macro 'pci_remap_iospace' defined
for those architectures that need a special treatment. Hence, put core API
function inside preprocesor conditional code for 'pci_remap_iospace'
definition.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210925203224.10419-5-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, the maximum link speed was set following an "fsl,max-link-speed"
property read, and should the read failed, then the PCIe generation was
manually set to PCIe Gen1 and thus limiting the link speed to 2.5 GT/s.
Code refactoring completed in the commit 39bc500650 ("PCI: dwc:
Centralize link gen setting") changed to the logic that was previously
used to limit the maximum link speed leaving behind an unused assignment
to a variable "ret".
Since the value returned from the of_property_read_u32() and stored in
the variable "ret" is never used in any meaningful way, and it's also
immediately reassigned in the code that follows, the assignment can be
removed.
Link: https://lore.kernel.org/r/20211003025439.84783-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Since commit 2a671f77ee ("s390/pci: fix use after free of zpci_dev")
the reference count of a zpci_dev is incremented between
pcibios_add_device() and pcibios_release_device() which was supposed to
prevent the zpci_dev from being freed while the common PCI code has
access to it. It was missed however that the handling of zPCI
availability events assumed that once zpci_zdev_put() was called no
later availability event would still see the device. With the previously
mentioned commit however this assumption no longer holds and we must
make sure that we only drop the initial long-lived reference the zPCI
subsystem holds exactly once.
Do so by introducing a zpci_device_reserved() function that handles when
a device is reserved. Here we make sure the zpci_dev will not be
considered for further events by removing it from the zpci_list.
This also means that the device actually stays in the
ZPCI_FN_STATE_RESERVED state between the time we know it has been
reserved and the final reference going away. We thus need to consider it
a real state instead of just a conceptual state after the removal. The
final cleanup of PCI resources, removal from zbus, and destruction of
the IOMMU stays in zpci_release_device() to make sure holders of the
reference do see valid data until the release.
Fixes: 2a671f77ee ("s390/pci: fix use after free of zpci_dev")
Cc: stable@vger.kernel.org
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Convert sprintf() in sysfs "show" functions to sysfs_emit() in order to
check for buffer overruns in sysfs outputs.
Link: https://lore.kernel.org/r/1630472957-26857-1-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Header file linux/pci_ids.h defines AMCC vendor id (0x10e8) macro named
PCI_VENDOR_ID_AMCC. So use this macro instead of driver custom macro.
Link: https://lore.kernel.org/r/20210927134356.11799-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
If the clock is provided externally we need to make sure it is enabled
before starting PCI scan.
Link: https://lore.kernel.org/r/20210531085934.2662457-5-luca@lucaceresoli.net
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Unused since commit e259c2926c ("PCI: pci-dra7xx: Prepare for deferred
probe with module_platform_driver").
Link: https://lore.kernel.org/r/20210531085934.2662457-4-luca@lucaceresoli.net
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Enable building the driver as a loadable kernel module.
Link: https://lore.kernel.org/r/20210531085934.2662457-3-luca@lucaceresoli.net
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
These symbols are used by the pci-dra7xx driver. Export them to allow
building pci-dra7xx as a module.
Link: https://lore.kernel.org/r/20210531085934.2662457-2-luca@lucaceresoli.net
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Built-in graphics at 07:00.0 on HP EliteDesk 805 G6 doesn't work because
graphics can't get the BAR it needs. The BIOS configuration is
correct: BARs 0 and 2 both fit in the 00:08.1 bridge window.
But that 00:08.1 window covers two host bridge apertures from _CRS.
Previously we assumed this was illegal, so we clipped the window to fit
into one aperture (see 0f7e7aee2f ("PCI: Add pci_bus_clip_resource() to
clip to fit upstream window")).
pci_bus 0000:00: root bus resource [mem 0x10020200000-0x100303fffff window]
pci_bus 0000:00: root bus resource [mem 0x10030400000-0x100401fffff window]
pci 0000:00:08.1: bridge window [mem 0x10030000000-0x100401fffff 64bit pref]
pci 0000:07:00.0: reg 0x10: [mem 0x10030000000-0x1003fffffff 64bit pref]
pci 0000:07:00.0: reg 0x18: [mem 0x10040000000-0x100401fffff 64bit pref]
pci 0000:00:08.1: can't claim BAR 15 [mem 0x10030000000-0x100401fffff 64bit pref]: no compatible bridge window
pci 0000:00:08.1: [mem 0x10030000000-0x100401fffff 64bit pref] clipped to [mem 0x10030000000-0x100303fffff 64bit pref]
pci 0000:00:08.1: bridge window [mem 0x10030000000-0x100303fffff 64bit pref]
pci 0000:07:00.0: can't claim BAR 0 [mem 0x10030000000-0x1003fffffff 64bit pref]: no compatible bridge window
pci 0000:07:00.0: can't claim BAR 2 [mem 0x10040000000-0x100401fffff 64bit pref]: no compatible bridge window
However, the host bridge apertures are contiguous, so there's no need to
clip in this case. Coalesce contiguous apertures so we can allocate from
the entire contiguous region.
Previous commit 65db04053e ("PCI: Coalesce host bridge contiguous
apertures") was similar but sorted the apertures, and Guenter Roeck
reported a regression in ppc:sam460ex qemu emulation from nvme; see
https://lore.kernel.org/all/20210709231529.GA3270116@roeck-us.net/
[bhelgaas: commit log]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=212013
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20210713125007.1260304-1-kai.heng.feng@canonical.com
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Using struct pci_platform_pm_ops for ACPI adds unnecessary
indirection to the interactions between the PCI core and ACPI PM,
which is also subject to retpolines.
Moreover, it is not particularly clear from the current code that,
as far as PCI PM is concerned, "platform" really means just ACPI
except for the special casess when Intel MID PCI PM is used or when
ACPI support is disabled (through the kernel config or command line,
or because there are no usable ACPI tables on the system).
To address the above, rework the PCI PM code to invoke ACPI PM
functions directly as needed and drop the acpi_pci_platform_pm
object that is not necessary any more.
Accordingly, update some of the ACPI PM functions in question to do
extra checks in case the ACPI support is disabled (which previously
was taken care of by avoiding to set the pci_platform_ops pointer
in those cases).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
strtobool() is a wrapper around kstrtobool() that has been added for
backward compatibility.
There is no reason to use the old API, so use kstrtobool() directly.
Related: ef95159907 ("lib: move strtobool() to kstrtobool()")
Link: https://lore.kernel.org/r/20210915230127.2495723-3-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Most of the "store" functions that handle userspace input via sysfs return
-EINVAL should the value fail validation and/or type conversion. This
error code is a clear message to userspace that the value is not a valid
input.
However, some of the "show" functions return input parsing error codes
as-is, which may be either -EINVAL or -ERANGE. The former would often be
from kstrtobool(), and the latter typically from other kstr*() functions
such as kstrtou8(), kstrtou32(), kstrtoint(), etc.
-EINVAL is commonly returned as the error code to indicate that the value
provided is invalid, but -ERANGE is not very useful in userspace.
Therefore, normalize the return error code to be -EINVAL for when the
validation and/or type conversion fails.
Link: https://lore.kernel.org/r/20210915230127.2495723-2-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Check if the "CAP_SYS_ADMIN" capability flag is set before parsing user
input as it makes more sense to first check whether the current user
actually has the right permissions before accepting any input from such
user.
This will also make order in which enable_store() and msi_bus_store()
perform the "CAP_SYS_ADMIN" capability check consistent with other
PCI-related sysfs objects that first verify whether user has this
capability set.
Link: https://lore.kernel.org/r/20210915230127.2495723-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
There are only two users of struct pci_platform_pm_ops in the tree,
one of which is Intel MID PM and the other one is ACPI. They are
mutually exclusive and the MID PM should take precedence when they
both are enabled, but whether or not this really is the case hinges
on the specific ordering of arch_initcall() calls made by them.
The struct pci_platform_pm_ops abstraction is not really necessary
for just these two users, but it adds complexity and overhead because
of retoplines involved in using all of the function pointers in there.
It also makes following the code a bit more difficult than it would
be otherwise.
Moreover, Intel MID PCI PM doesn't even implement the majority of the
function pointers in struct pci_platform_pm_ops in a meaningful way,
so switch over the PCI core to calling the relevant MID PM routines,
mid_pci_set_power_state() and mid_pci_set_power_state(), directly as
needed and drop mid_pci_platform_pm.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
The acpi_pci_bus structure was used primarily for running
acpi_pci_find_companion() during PCI device objects registration,
but after commit 375553a932 ("PCI: Setup ACPI fwnode early and at
the same time with OF") that function is called by pci_setup_device()
via pci_set_acpi_fwnode(), which happens before calling
pci_device_add() on the new PCI device object, so its ACPI companion
has been set already when acpi_device_notify() runs and it will never
call ->find_companion() from acpi_pci_bus.
For this reason, modify acpi_device_notify() and
acpi_device_notify_remove() to call pci_acpi_setup() and
pci_acpi_cleanup(), respectively, directly on PCI device objects
and drop acpi_pci_bus altogether.
While at it, notice that pci_acpi_setup() and pci_acpi_cleanup()
can obtain the ACPI companion pointer, which is guaranteed to not
be NULL, from their callers and modify them to work that way so
as to reduce the number of redundant checks somewhat.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCYU8xegAKCRCAXGG7T9hj
vvk2APwM85dFSMNHQo5+S35X+h+M8uKuqqvPYxVtKqQEwu3LXAEAg0cVgr1lWegI
X98f07/+M0rPJl24kgW/EIxAD9fsWAw=
=JILz
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.15b-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Some minor cleanups and fixes of some theoretical bugs, as well as a
fix of a bug introduced in 5.15-rc1"
* tag 'for-linus-5.15b-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/x86: fix PV trap handling on secondary processors
xen/balloon: fix balloon kthread freezing
swiotlb-xen: this is PV-only on x86
xen/pci-swiotlb: reduce visibility of symbols
PCI: only build xen-pcifront in PV-enabled environments
swiotlb-xen: ensure to issue well-formed XENMEM_exchange requests
Xen/gntdev: don't ignore kernel unmapping error
xen/x86: drop redundant zeroing from cpu_initialize_context()
In hv_pci_bus_exit, the code is holding a spinlock while calling
pci_destroy_slot(), which takes a mutex.
This is not safe for spinlock. Fix this by moving the children to be
deleted to a list on the stack, and removing them after spinlock is
released.
Fixes: 94d2276320 ("PCI: hv: Fix a race condition when removing the device")
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Wei Liu <wei.liu@kernel.org>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Rob Herring <robh@kernel.org>
Cc: "Krzysztof Wilczyński" <kw@linux.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michael Kelley <mikelley@microsoft.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/linux-hyperv/20210823152130.GA21501@kili/
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: Wei Liu <wei.liu@kernel.org>
Link: https://lore.kernel.org/r/1630365207-20616-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
The general convention for pcibios_* hooks is that they're named after the
corresponding pci_* function they provide a hook for. The exception is
pcibios_add_device() which provides a hook for pci_device_add().
Rename pcibios_add_device() to pcibios_device_add() so it matches
pci_device_add().
Also, remove the export of the microblaze version. The only caller must be
compiled as a built-in so there's no reason for the export.
Link: https://lore.kernel.org/r/20210913152709.48013-1-oohall@gmail.com
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Niklas Schnelle <schnelle@linux.ibm.com> # s390
Avoid registering service IRQs if there is no service that offers them
or no driver to register a handler against them. This saves IRQ vectors
when they are limited (e.g. on x86) and also avoids that spurious events
could hit a missing handler. Such spurious events need to be generated
by the Jailhouse hypervisor for active MSI vectors when enabling or
disabling itself.
Link: https://lore.kernel.org/r/8f9a13ac-8ab1-15ac-06cb-c131b488a36f@siemens.com
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When passing the Atheros QCA6174 through to a virtual machine, the VM hangs
at the point where the ath10k driver loads.
Add a quirk to avoid bus resets on this device, which avoids the hang.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/08982e05-b6e8-5a8d-24ab-da1488ee50a8@web.de
Signed-off-by: Ingmar Klein <ingmar_klein@web.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Cc: stable@vger.kernel.org
The bus offset is bus address - physical address, so the calculation in
__pci_p2pdma_map_sg should be: bus address = physical address + bus offset.
Correct the dma_address computation in __pci_p2pdma_map_sg().
Link: https://lore.kernel.org/r/20210909032528.24517-1-wanglu@dapustor.com
Signed-off-by: Wang Lu <wanglu@dapustor.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
The driver's module init function, pcifront_init(), invokes
xen_pv_domain() first thing. That construct produces constant "false"
when !CONFIG_XEN_PV. Hence there's no point building the driver in
non-PV configurations.
Drop the (now implicit and generally wrong) X86 dependency: At present,
XEN_PV can only be set when X86 is also enabled. In general an
architecture supporting Xen PV (and PCI) would want to have this driver
built.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/3a7f6c9b-215d-b593-8056-b5fe605dafd7@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Some AMD GPUs have built-in USB xHCI and USB Type-C UCSI controllers with
power dependencies between the GPU and the other functions as in
6d2e369f0d ("PCI: Add NVIDIA GPU multi-function power dependencies").
Add device link support for the AMD integrated USB xHCI and USB Type-C UCSI
controllers.
Without this, runtime power management, including GPU resume and temp and
fan sensors don't work correctly.
Reported-at: https://gitlab.freedesktop.org/drm/amd/-/issues/1704
Link: https://lore.kernel.org/r/20210903063311.3606226-1-evan.quan@amd.com
Signed-off-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Commit 375553a932 ("PCI: Setup ACPI fwnode early and at the same time
with OF") added a call to pci_set_acpi_fwnode() in pci_setup_device(),
which unconditionally clears any fwnode previously set by
pci_set_of_node().
pci_set_acpi_fwnode() looks for ACPI_COMPANION(), which only returns the
existing fwnode if it was set by ACPI_COMPANION_SET(). If it was set by
OF instead, ACPI_COMPANION() returns NULL and pci_set_acpi_fwnode()
accidentally clears the fwnode. To fix this, look for any fwnode instead
of just ACPI companions.
Fixes a virtio-iommu boot regression in v5.15-rc1.
Fixes: 375553a932 ("PCI: Setup ACPI fwnode early and at the same time with OF")
Link: https://lore.kernel.org/r/20210913172358.1775381-1-jean-philippe@linaro.org
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
7bac54497c ("PCI/VPD: Determine VPD size in pci_vpd_init()") reads VPD at
enumeration-time to find the size. But this is quite slow, and we don't
need the size until we actually need data from VPD. Dave reported a boot
slowdown of more than two minutes [1].
Defer the VPD sizing until a driver or the user (via sysfs) requests
information from VPD.
If devices are quirked because VPD is known not to work, don't bother even
looking for the VPD capability. The VPD will not be accessible at all.
[1] https://lore.kernel.org/r/20210913141818.GA27911@codemonkey.org.uk/
Link: https://lore.kernel.org/r/20210914215543.GA1437800@bjorn-Precision-5520
Fixes: 7bac54497c ("PCI/VPD: Determine VPD size in pci_vpd_init()")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Add ACPI support to the PCI VMD driver (Rafael Wysocki).
- Rearrange suspend-to-idle support code to reflect the platform
firmware expectations on some AMD platforms (Mario Limonciello).
- Make SSDT overlays documentation follow the code documented by it
more closely (Andy Shevchenko).
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEE4fcc61cGeeHD/fCwgsRv/nhiVHEFAmE41EgSHHJqd0Byand5
c29ja2kubmV0AAoJEILEb/54YlRxZrgP/iStcM1PdEkzW9KInTbI7MDiQl8Iaem2
4AcbrsQmJxAEfJ+kzUuoArjj+y4T8sf49AA9Akg/q3zwf0oBix8JdtPDEx823oG8
7/0zjPJMigmcmGfGIlnQaSYqE30hatsthqF0iyH9AZjRzM1m9MavAtxrwDOD0Chq
m6kMObNorm/C0mjdPy71DAbiPbrcsMTFjw27hXHWnfsQFhZeVAoyhh2aFvk790pG
QRxpArI8r3dLb9vORQWo0q4jezPrRU6HzfvULVZEtv5+F8VUAby+qi1oGUSNx6CX
OB20Z1MFPSolsJvyRkfE8HEq0x1Es37doBROolhmliaKUQezwKPMZKJGgEYyUaSJ
bnWmN2wuE39VB6rIWXIaw6bHX3RwWnUJgoMvTZZIexp4kmmy9nsPB119na2odFVW
D06yMPZwx9lCDVWNkIbpcCGHkBWvQSZ+X/tROVOgyutJ2Rgph0PTVxQxVZmTnTWm
Pq6Tp8lSeatL16vEY75EX5pXbmKiGDIFrGv28Jxou2Arf31hcagY+rxu6YYORefu
NdkC2GD4TlQMGm2Ukfo5D/svFzJ/MQvP75ytVP3Oqi7ZFLkU2RzYOun8oOcZjUk6
76CH5/fmSvV2NbZRCDzhxiDXVhBFPaGm0KFnYYKs1V7AskdhnzOkd03z2bseTC0V
XNk0fHL1R38J
=8lPe
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.15-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These add ACPI support to the PCI VMD driver, improve suspend-to-idle
support for AMD platforms and update documentation.
Specifics:
- Add ACPI support to the PCI VMD driver (Rafael Wysocki)
- Rearrange suspend-to-idle support code to reflect the platform
firmware expectations on some AMD platforms (Mario Limonciello)
- Make SSDT overlays documentation follow the code documented by it
more closely (Andy Shevchenko)"
* tag 'acpi-5.15-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: PM: s2idle: Run both AMD and Microsoft methods if both are supported
Documentation: ACPI: Align the SSDT overlays file with the code
PCI: VMD: ACPI: Make ACPI companion lookup work for VMD bus
Pull swiotlb updates from Konrad Rzeszutek Wilk:
"A new feature called restricted DMA pools. It allows SWIOTLB to
utilize per-device (or per-platform) allocated memory pools instead of
using the global one.
The first big user of this is ARM Confidential Computing where the
memory for DMA operations can be set per platform"
* 'stable/for-linus-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb: (23 commits)
swiotlb: use depends on for DMA_RESTRICTED_POOL
of: restricted dma: Don't fail device probe on rmem init failure
of: Move of_dma_set_restricted_buffer() into device.c
powerpc/svm: Don't issue ultracalls if !mem_encrypt_active()
s390/pv: fix the forcing of the swiotlb
swiotlb: Free tbl memory in swiotlb_exit()
swiotlb: Emit diagnostic in swiotlb_exit()
swiotlb: Convert io_default_tlb_mem to static allocation
of: Return success from of_dma_set_restricted_buffer() when !OF_ADDRESS
swiotlb: add overflow checks to swiotlb_bounce
swiotlb: fix implicit debugfs declarations
of: Add plumbing for restricted DMA pool
dt-bindings: of: Add restricted DMA pool
swiotlb: Add restricted DMA pool initialization
swiotlb: Add restricted DMA alloc/free support
swiotlb: Refactor swiotlb_tbl_unmap_single
swiotlb: Move alloc_size to swiotlb_find_slots
swiotlb: Use is_swiotlb_force_bounce for swiotlb data bouncing
swiotlb: Update is_swiotlb_active to add a struct device argument
swiotlb: Update is_swiotlb_buffer to add a struct device argument
...
- Fix dma-valid return WAITED implementation (Anthony Yznaga)
- SPDX license cleanups (Cai Huoqing)
- Split vfio-pci-core from vfio-pci and enhance PCI driver matching
to support future vendor provided vfio-pci variants (Yishai Hadas,
Max Gurtovoy, Jason Gunthorpe)
- Replace duplicated reflck with core support for managing first
open, last close, and device sets (Jason Gunthorpe, Max Gurtovoy,
Yishai Hadas)
- Fix non-modular mdev support and don't nag about request callback
support (Christoph Hellwig)
- Add semaphore to protect instruction intercept handler and replace
open-coded locks in vfio-ap driver (Tony Krowiak)
- Convert vfio-ap to vfio_register_group_dev() API (Jason Gunthorpe)
-----BEGIN PGP SIGNATURE-----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=nzK7
-----END PGP SIGNATURE-----
Merge tag 'vfio-v5.15-rc1' of git://github.com/awilliam/linux-vfio
Pull VFIO updates from Alex Williamson:
- Fix dma-valid return WAITED implementation (Anthony Yznaga)
- SPDX license cleanups (Cai Huoqing)
- Split vfio-pci-core from vfio-pci and enhance PCI driver matching to
support future vendor provided vfio-pci variants (Yishai Hadas, Max
Gurtovoy, Jason Gunthorpe)
- Replace duplicated reflck with core support for managing first open,
last close, and device sets (Jason Gunthorpe, Max Gurtovoy, Yishai
Hadas)
- Fix non-modular mdev support and don't nag about request callback
support (Christoph Hellwig)
- Add semaphore to protect instruction intercept handler and replace
open-coded locks in vfio-ap driver (Tony Krowiak)
- Convert vfio-ap to vfio_register_group_dev() API (Jason Gunthorpe)
* tag 'vfio-v5.15-rc1' of git://github.com/awilliam/linux-vfio: (37 commits)
vfio/pci: Introduce vfio_pci_core.ko
vfio: Use kconfig if XX/endif blocks instead of repeating 'depends on'
vfio: Use select for eventfd
PCI / VFIO: Add 'override_only' support for VFIO PCI sub system
PCI: Add 'override_only' field to struct pci_device_id
vfio/pci: Move module parameters to vfio_pci.c
vfio/pci: Move igd initialization to vfio_pci.c
vfio/pci: Split the pci_driver code out of vfio_pci_core.c
vfio/pci: Include vfio header in vfio_pci_core.h
vfio/pci: Rename ops functions to fit core namings
vfio/pci: Rename vfio_pci_device to vfio_pci_core_device
vfio/pci: Rename vfio_pci_private.h to vfio_pci_core.h
vfio/pci: Rename vfio_pci.c to vfio_pci_core.c
vfio/ap_ops: Convert to use vfio_register_group_dev()
s390/vfio-ap: replace open coded locks for VFIO_GROUP_NOTIFY_SET_KVM notification
s390/vfio-ap: r/w lock for PQAP interception handler function pointer
vfio/type1: Fix vfio_find_dma_valid return
vfio-pci/zdev: Remove repeated verbose license text
vfio: platform: reset: Convert to SPDX identifier
vfio: Remove struct vfio_device_ops open/release
...
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCYTB6pAAKCRCAXGG7T9hj
vk9xAP9hUQtGdTb5eW9+3X3PHDON2jGbydAMtQ57WJLdqj0oFgD/cGV95PKv0jgg
zgw6Icf9Vp6APF/Ucd/dOB0B6qviJgw=
=PNRc
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.15-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
- some small cleanups
- a fix for a bug when running as Xen PV guest which could result in
not all memory being transferred in case of a migration of the guest
- a small series for getting rid of code for supporting very old Xen
hypervisor versions nobody should be using since many years now
- a series for hardening the Xen block frontend driver
- a fix for Xen PV boot code issuing warning messages due to a stray
preempt_disable() on the non-boot processors
* tag 'for-linus-5.15-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: remove stray preempt_disable() from PV AP startup code
xen/pcifront: Removed unnecessary __ref annotation
x86: xen: platform-pci-unplug: use pr_err() and pr_warn() instead of raw printk()
drivers/xen/xenbus/xenbus_client.c: fix bugon.cocci warnings
xen/blkfront: don't trust the backend response data blindly
xen/blkfront: don't take local copy of a request from the ring page
xen/blkfront: read response from backend only once
xen: assume XENFEAT_gnttab_map_avail_bits being set for pv guests
xen: assume XENFEAT_mmu_pt_update_preserve_ad being set for pv guests
xen: check required Xen features
xen: fix setting of max_pfn in shared_info
- Add max-virtual-functions to endpoint binding (Kishon Vijay Abraham I)
- Add pci_epf_add_vepf() API to add virtual function to endpoint (Kishon
Vijay Abraham I)
- Add pci_epf_vepf_link() to link virtual function to endpoint physical
function (Kishon Vijay Abraham I)
- Add virtual function number to pci_epc_ops endpoint ops interfaces
(Kishon Vijay Abraham I)
- Simplify register base address computation for endpoint BAR configuration
(Kishon Vijay Abraham I)
- Add support to configure virtual functions in cadence endpoint driver
(Kishon Vijay Abraham I)
- Add SR-IOV configuration to endpoint test driver (Kishon Vijay Abraham I)
- Document configfs usage to create virtual functions for endpoints (Kishon
Vijay Abraham I)
* remotes/lorenzo/pci/endpoint:
Documentation: PCI: endpoint/pci-endpoint-cfs: Guide to use SR-IOV
misc: pci_endpoint_test: Populate sriov_configure ops to configure SR-IOV device
PCI: cadence: Add support to configure virtual functions
PCI: cadence: Simplify code to get register base address for configuring BAR
PCI: endpoint: Add virtual function number in pci_epc ops
PCI: endpoint: Add support to link a physical function to a virtual function
PCI: endpoint: Add support to add virtual function in endpoint core
dt-bindings: PCI: pci-ep: Add binding to specify virtual function
- Fix runtime PM imbalance in rcar_pcie_ep_probe() (Dinghao Liu)
* remotes/lorenzo/pci/rcar:
PCI: rcar: Add L1 link state fix into data abort hook
PCI: rcar: Fix runtime PM imbalance in rcar_pcie_ep_probe()
- Split DT bindings for PCIe controllers with independent MSI domains into
separate nodes for MT2712/MT7622 (Chuanjia Liu)
- Locate shared registers from "mediatek,generic-pciecfg" property
(Chuanjia Liu)
- Get IRQ from "pcie_irq" if "interrupt-names" property is present to fix
an MSI issue (Chuanjia Liu)
- Get PCI domain from "linux,pci-domain" property if present (Chuanjia Liu)
* remotes/lorenzo/pci/mediatek:
PCI: mediatek: Use PCI domain to handle ports detection
PCI: mediatek: Add new method to get irq number
PCI: mediatek: Add new method to get shared pcie-cfg base address
dt-bindings: PCI: mediatek: Update the Device tree bindings
- Add domain_nr in struct pci_host_bridge (Boqun Feng)
- Use host bridge MSI domain for root buses if present (Boqun Feng)
- Allow ARM64 virtual host bridge with no ACPI companion (e.g., Hyper-V)
(Boqun Feng)
- Make Hyper-V enumeration more generic (Arnd Bergmann)
- Set Hyper-V domain_nr at probe-time (Boqun Feng)
- Set up Hyper-V MSI domain at bridge probe-time (Boqun Feng)
- Enable Hyper-V bridge probing on ARM64 (Boqun Feng)
* remotes/lorenzo/pci/hyper-v:
PCI: hv: Turn on the host bridge probing on ARM64
PCI: hv: Set up MSI domain at bridge probing time
PCI: hv: Set ->domain_nr of pci_host_bridge at probing time
PCI: hv: Generify PCI probing
arm64: PCI: Support root bridge preparation for Hyper-V
arm64: PCI: Restructure pcibios_root_bridge_prepare()
PCI: Support populating MSI domains of root buses via bridges
PCI: Introduce domain_nr in pci_host_bridge
- Convert bool in structs to bitfield (Kishon Vijay Abraham I)
- Work around J7200 non-PCIe SERDES lane electrical issue that prevents
PCIe link training (Nadeem Athani)
- Add J7200 PCIe support to j721e (Kishon Vijay Abraham I)
- Add AM64 PCIe support to j721e (Kishon Vijay Abraham I)
- Add J7200 and AM64 device IDs to endpoint test (Kishon Vijay Abraham I)
* remotes/lorenzo/pci/cadence:
misc: pci_endpoint_test: Add deviceID for AM64 and J7200
PCI: j721e: Add PCIe support for AM64
PCI: j721e: Add PCIe support for J7200
PCI: cadence: Add quirk flag to set minimum delay in LTSSM Detect.Quiet state
PCI: cadence: Use bitfield for *quirk_retrain_flag* instead of bool
- Fix PIO config access status checking (Evan Wang)
- Increase config access polling delay to 1.5s (Pali Rohár)
- Add PCIe Root Capabilities to bridge emulation (Pali Rohár)
- Report Config Request Retry Status when Software Visibility enabled (Pali
Rohár)
- Add back configuration of PCIe resources from 'ranges' DT property and
pay attention to DT size and CPU/PCI offset to fix issues with I/O port
space (Pali Rohár)
- Serialize masking and unmasking legacy INTx interrupts (Pali Rohár)
* remotes/lorenzo/pci/aardvark:
PCI: aardvark: Fix masking and unmasking legacy INTx interrupts
PCI: aardvark: Configure PCIe resources from 'ranges' DT property
PCI: aardvark: Fix reporting CRS value
PCI: pci-bridge-emul: Add PCIe Root Capabilities Register
PCI: aardvark: Increase polling delay to 1.5s while waiting for PIO response
PCI: aardvark: Fix checking for PIO status
- Cache PCIe Device Capabilities register (Amey Narkhede)
- Add pcie_reset_flr() with 'probe' argument (Amey Narkhede)
- Add pdev->reset_methods[] array to track reset method ordering (Amey
Narkhede)
- Remove reset_fn field from pci_dev (Amey Narkhede)
- Add sysfs interface to query and set device reset mechanism (Amey
Narkhede)
- Add pci_set_acpi_fwnode() to set ACPI_COMPANION (Shanker Donthineni)
- Use acpi_pci_power_manageable() instead of duplicating logic (Shanker
Donthineni)
- Set ACPI fwnode early and at the same time with OF (Shanker Donthineni)
- Add support for ACPI _RST reset method (Shanker Donthineni)
- Change reset function 'probe' argument to bool (Amey Narkhede)
* pci/reset:
PCI: Change the type of probe argument in reset functions
PCI: Add support for ACPI _RST reset method
PCI: Setup ACPI fwnode early and at the same time with OF
PCI: Use acpi_pci_power_manageable()
PCI: Add pci_set_acpi_fwnode() to set ACPI_COMPANION
PCI: Allow userspace to query and set device reset mechanism
PCI: Remove reset_fn field from pci_dev
PCI: Add array to track reset method ordering
PCI: Add pcie_reset_flr() with 'probe' argument
PCI: Cache PCIe Device Capabilities register
- Enable Bandwidth Notification only if port supports it (Stuart Hayes)
* pci/portdrv:
PCI/portdrv: Enable Bandwidth Notification only if port supports it
ebda_rsrc_controller() calls iounmap(io_mem) on the error path. Its caller,
ibmphp_access_ebda(), also calls iounmap(io_mem) on good and error paths.
Remove the iounmap(io_mem) invocation from ebda_rsrc_controller().
[bhelgaas: remove item from TODO]
Link: https://lore.kernel.org/r/20210818165751.591185-1-os.vaslot@gmail.com
Signed-off-by: Vishal Aslot <os.vaslot@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
On some systems, in order to get to the deepest low-power state of
the platform (which may be necessary to save significant enough
amounts of energy while suspended to idle. for example), devices on
the PCI bus exposed by the VMD driver need to be power-managed via
ACPI. However, the layout of the ACPI namespace below the VMD
controller device object does not reflect the layout of the PCI bus
under the VMD host bridge, so in order to identify the ACPI companion
objects for the devices on that bus, it is necessary to use a special
_ADR encoding on the ACPI side. In other words, acpi_pci_find_companion()
does not work for these devices, so it needs to be amended with a
special lookup logic specific to the VMD bus.
Address this issue by allowing the VMD driver to temporarily install
an ACPI companion lookup hook containing the code matching the devices
on the VMD PCI bus with the corresponding objects in the ACPI
namespace.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jon Derrick <jonathan.derrick@intel.com>
Here is the big set of driver core patches for 5.15-rc1.
These do change a number of different things across different
subsystems, and because of that, there were 2 stable tags created that
might have already come into your tree from different pulls that did the
following
- changed the bus remove callback to return void
- sysfs iomem_get_mapping rework
The latter one will cause a tiny merge issue with your tree, as there
was a last-minute fix for this in 5.14 in your tree, but the fixup
should be "obvious". If you want me to provide a fixed merge for this,
please let me know.
Other than those two things, there's only a few small things in here:
- kernfs performance improvements for huge numbers of sysfs
users at once
- tiny api cleanups
- other minor changes
All of these have been in linux-next for a while with no reported
problems, other than the before-mentioned merge issue.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYS+FLQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylXuACfWECnysDtXNe66DdETCFs1a1RToYAoMokWeU5
s8VFP1NY2BjmxJbkebLL
=8kVu
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big set of driver core patches for 5.15-rc1.
These do change a number of different things across different
subsystems, and because of that, there were 2 stable tags created that
might have already come into your tree from different pulls that did
the following
- changed the bus remove callback to return void
- sysfs iomem_get_mapping rework
Other than those two things, there's only a few small things in here:
- kernfs performance improvements for huge numbers of sysfs users at
once
- tiny api cleanups
- other minor changes
All of these have been in linux-next for a while with no reported
problems, other than the before-mentioned merge issue"
* tag 'driver-core-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (33 commits)
MAINTAINERS: Add dri-devel for component.[hc]
driver core: platform: Remove platform_device_add_properties()
ARM: tegra: paz00: Handle device properties with software node API
bitmap: extend comment to bitmap_print_bitmask/list_to_buf
drivers/base/node.c: use bin_attribute to break the size limitation of cpumap ABI
topology: use bin_attribute to break the size limitation of cpumap ABI
lib: test_bitmap: add bitmap_print_bitmask/list_to_buf test cases
cpumask: introduce cpumap_print_list/bitmask_to_buf to support large bitmask and list
sysfs: Rename struct bin_attribute member to f_mapping
sysfs: Invoke iomem_get_mapping() from the sysfs open callback
debugfs: Return error during {full/open}_proxy_open() on rmmod
zorro: Drop useless (and hardly used) .driver member in struct zorro_dev
zorro: Simplify remove callback
sh: superhyway: Simplify check in remove callback
nubus: Simplify check in remove callback
nubus: Make struct nubus_driver::remove return void
kernfs: dont call d_splice_alias() under kernfs node lock
kernfs: use i_lock to protect concurrent inode updates
kernfs: switch kernfs to use an rwsem
kernfs: use VFS negative dentry caching
...
An unnecessary "__ref" annotation was removed from the
"drivers/pci/xen_pcifront.c" file. The function where the annotation
was used was "pcifront_backend_changed()", which does not call any
functions annotated as "__*init" nor "__*exit". This makes "__ref"
unnecessary since this annotation is used to make the compiler ignore
section miss-matches when they are not happening here in the first
place.
In addition to the aforementioned change, some code style issues were
fixed in the same file.
Signed-off-by: Sergio Miguéns Iglesias <sergio@lony.xyz>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20210830175305.13370-1-sergio@lony.xyz
Signed-off-by: Juergen Gross <jgross@suse.com>
- Enable memcg accounting for various networking objects.
BPF:
- Introduce bpf timers.
- Add perf link and opaque bpf_cookie which the program can read
out again, to be used in libbpf-based USDT library.
- Add bpf_task_pt_regs() helper to access user space pt_regs
in kprobes, to help user space stack unwinding.
- Add support for UNIX sockets for BPF sockmap.
- Extend BPF iterator support for UNIX domain sockets.
- Allow BPF TCP congestion control progs and bpf iterators to call
bpf_setsockopt(), e.g. to switch to another congestion control
algorithm.
Protocols:
- Support IOAM Pre-allocated Trace with IPv6.
- Support Management Component Transport Protocol.
- bridge: multicast: add vlan support.
- netfilter: add hooks for the SRv6 lightweight tunnel driver.
- tcp:
- enable mid-stream window clamping (by user space or BPF)
- allow data-less, empty-cookie SYN with TFO_SERVER_COOKIE_NOT_REQD
- more accurate DSACK processing for RACK-TLP
- mptcp:
- add full mesh path manager option
- add partial support for MP_FAIL
- improve use of backup subflows
- optimize option processing
- af_unix: add OOB notification support.
- ipv6: add IFLA_INET6_RA_MTU to expose MTU value advertised by
the router.
- mac80211: Target Wake Time support in AP mode.
- can: j1939: extend UAPI to notify about RX status.
Driver APIs:
- Add page frag support in page pool API.
- Many improvements to the DSA (distributed switch) APIs.
- ethtool: extend IRQ coalesce uAPI with timer reset modes.
- devlink: control which auxiliary devices are created.
- Support CAN PHYs via the generic PHY subsystem.
- Proper cross-chip support for tag_8021q.
- Allow TX forwarding for the software bridge data path to be
offloaded to capable devices.
Drivers:
- veth: more flexible channels number configuration.
- openvswitch: introduce per-cpu upcall dispatch.
- Add internet mix (IMIX) mode to pktgen.
- Transparently handle XDP operations in the bonding driver.
- Add LiteETH network driver.
- Renesas (ravb):
- support Gigabit Ethernet IP
- NXP Ethernet switch (sja1105)
- fast aging support
- support for "H" switch topologies
- traffic termination for ports under VLAN-aware bridge
- Intel 1G Ethernet
- support getcrosststamp() with PCIe PTM (Precision Time
Measurement) for better time sync
- support Credit-Based Shaper (CBS) offload, enabling HW traffic
prioritization and bandwidth reservation
- Broadcom Ethernet (bnxt)
- support pulse-per-second output
- support larger Rx rings
- Mellanox Ethernet (mlx5)
- support ethtool RSS contexts and MQPRIO channel mode
- support LAG offload with bridging
- support devlink rate limit API
- support packet sampling on tunnels
- Huawei Ethernet (hns3):
- basic devlink support
- add extended IRQ coalescing support
- report extended link state
- Netronome Ethernet (nfp):
- add conntrack offload support
- Broadcom WiFi (brcmfmac):
- add WPA3 Personal with FT to supported cipher suites
- support 43752 SDIO device
- Intel WiFi (iwlwifi):
- support scanning hidden 6GHz networks
- support for a new hardware family (Bz)
- Xen pv driver:
- harden netfront against malicious backends
- Qualcomm mobile
- ipa: refactor power management and enable automatic suspend
- mhi: move MBIM to WWAN subsystem interfaces
Refactor:
- Ambient BPF run context and cgroup storage cleanup.
- Compat rework for ndo_ioctl.
Old code removal:
- prism54 remove the obsoleted driver, deprecated by the p54 driver.
- wan: remove sbni/granch driver.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=JDGD
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- Enable memcg accounting for various networking objects.
BPF:
- Introduce bpf timers.
- Add perf link and opaque bpf_cookie which the program can read out
again, to be used in libbpf-based USDT library.
- Add bpf_task_pt_regs() helper to access user space pt_regs in
kprobes, to help user space stack unwinding.
- Add support for UNIX sockets for BPF sockmap.
- Extend BPF iterator support for UNIX domain sockets.
- Allow BPF TCP congestion control progs and bpf iterators to call
bpf_setsockopt(), e.g. to switch to another congestion control
algorithm.
Protocols:
- Support IOAM Pre-allocated Trace with IPv6.
- Support Management Component Transport Protocol.
- bridge: multicast: add vlan support.
- netfilter: add hooks for the SRv6 lightweight tunnel driver.
- tcp:
- enable mid-stream window clamping (by user space or BPF)
- allow data-less, empty-cookie SYN with TFO_SERVER_COOKIE_NOT_REQD
- more accurate DSACK processing for RACK-TLP
- mptcp:
- add full mesh path manager option
- add partial support for MP_FAIL
- improve use of backup subflows
- optimize option processing
- af_unix: add OOB notification support.
- ipv6: add IFLA_INET6_RA_MTU to expose MTU value advertised by the
router.
- mac80211: Target Wake Time support in AP mode.
- can: j1939: extend UAPI to notify about RX status.
Driver APIs:
- Add page frag support in page pool API.
- Many improvements to the DSA (distributed switch) APIs.
- ethtool: extend IRQ coalesce uAPI with timer reset modes.
- devlink: control which auxiliary devices are created.
- Support CAN PHYs via the generic PHY subsystem.
- Proper cross-chip support for tag_8021q.
- Allow TX forwarding for the software bridge data path to be
offloaded to capable devices.
Drivers:
- veth: more flexible channels number configuration.
- openvswitch: introduce per-cpu upcall dispatch.
- Add internet mix (IMIX) mode to pktgen.
- Transparently handle XDP operations in the bonding driver.
- Add LiteETH network driver.
- Renesas (ravb):
- support Gigabit Ethernet IP
- NXP Ethernet switch (sja1105):
- fast aging support
- support for "H" switch topologies
- traffic termination for ports under VLAN-aware bridge
- Intel 1G Ethernet
- support getcrosststamp() with PCIe PTM (Precision Time
Measurement) for better time sync
- support Credit-Based Shaper (CBS) offload, enabling HW traffic
prioritization and bandwidth reservation
- Broadcom Ethernet (bnxt)
- support pulse-per-second output
- support larger Rx rings
- Mellanox Ethernet (mlx5)
- support ethtool RSS contexts and MQPRIO channel mode
- support LAG offload with bridging
- support devlink rate limit API
- support packet sampling on tunnels
- Huawei Ethernet (hns3):
- basic devlink support
- add extended IRQ coalescing support
- report extended link state
- Netronome Ethernet (nfp):
- add conntrack offload support
- Broadcom WiFi (brcmfmac):
- add WPA3 Personal with FT to supported cipher suites
- support 43752 SDIO device
- Intel WiFi (iwlwifi):
- support scanning hidden 6GHz networks
- support for a new hardware family (Bz)
- Xen pv driver:
- harden netfront against malicious backends
- Qualcomm mobile
- ipa: refactor power management and enable automatic suspend
- mhi: move MBIM to WWAN subsystem interfaces
Refactor:
- Ambient BPF run context and cgroup storage cleanup.
- Compat rework for ndo_ioctl.
Old code removal:
- prism54 remove the obsoleted driver, deprecated by the p54 driver.
- wan: remove sbni/granch driver"
* tag 'net-next-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1715 commits)
net: Add depends on OF_NET for LiteX's LiteETH
ipv6: seg6: remove duplicated include
net: hns3: remove unnecessary spaces
net: hns3: add some required spaces
net: hns3: clean up a type mismatch warning
net: hns3: refine function hns3_set_default_feature()
ipv6: remove duplicated 'net/lwtunnel.h' include
net: w5100: check return value after calling platform_get_resource()
net/mlxbf_gige: Make use of devm_platform_ioremap_resourcexxx()
net: mdio: mscc-miim: Make use of the helper function devm_platform_ioremap_resource()
net: mdio-ipq4019: Make use of devm_platform_ioremap_resource()
fou: remove sparse errors
ipv4: fix endianness issue in inet_rtm_getroute_build_skb()
octeontx2-af: Set proper errorcode for IPv4 checksum errors
octeontx2-af: Fix static code analyzer reported issues
octeontx2-af: Fix mailbox errors in nix_rss_flowkey_cfg
octeontx2-af: Fix loop in free and unmap counter
af_unix: fix potential NULL deref in unix_dgram_connect()
dpaa2-eth: Replace strlcpy with strscpy
octeontx2-af: Use NDC TX for transmit packet data
...
After recent introduction of new VPD API functions and user migration
these defines and inline functions aren't used outside VPD core any
longer.
Link: https://lore.kernel.org/r/d33e06bf-bc5e-ece7-bf35-7245ae224d1b@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a pci_vpd_find_id_string() API function to retrieve the ID string from
VPD.
This way callers don't need pci_vpd_lrdt_size() any longer, and it can be
made private to the VPD core.
Link: https://lore.kernel.org/r/c5225bf6-8d29-970d-e271-0d7b52252630@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move pci_vpd_find_tag() post-processing from pci_vpd_find_ro_info_keyword()
to pci_vpd_find_tag(). This simplifies function pci_vpd_find_id_string()
that will be added in a subsequent patch.
Link: https://lore.kernel.org/r/fb15393f-d3b2-e140-2643-570d3abd7382@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Now that the last users have been migrated to pci_vpd_find_ro_keyword()
we can stop exporting this function. It's still used in VPD core code.
Link: https://lore.kernel.org/r/96ca2a56-383e-9b61-9cba-4f1e5611dc15@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Now that the last users have been migrated to pci_vpd_find_ro_keyword()
we can stop exporting this function. It's still used in VPD core code.
Link: https://lore.kernel.org/r/71131eca-0502-7878-365f-30b6614161cf@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Address 3 PCI device power management issues (Rafael Wysocki).
- Add Power Limit4 support for Alder Lake to the Intel RAPL power
capping driver (Sumeet Pawnikar).
- Add HWP guaranteed performance change notification support to
the intel_pstate driver (Srinivas Pandruvada).
- Replace deprecated CPU-hotplug functions in code related to power
management (Sebastian Andrzej Siewior).
- Update CPU PM notifiers to use raw spinlocks (Valentin Schneider).
- Add support for 'required-opps' DT property to the generic power
domains (genpd) framework and use this property for I2C on ARM64
sc7180 (Rajendra Nayak).
- Fix Kconfig issue related to genpd (Geert Uytterhoeven).
- Increase energy calculation precision in the Energy Model (Lukasz
Luba).
- Fix kobject deletion in the exit code of the schedutil cpufreq
governor (Kevin Hao).
- Unmark some functions as kernel-doc in the PM core to avoid
false-positive documentation build warnings (Randy Dunlap).
- Check RTC features instead of ops in suspend_test Alexandre
Belloni).
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEE4fcc61cGeeHD/fCwgsRv/nhiVHEFAmEtIvYSHHJqd0Byand5
c29ja2kubmV0AAoJEILEb/54YlRxnQ8QAK2QCyfFAdrPE3zn+XdTcVC8rpYhL0d2
3YpbS2obZ4lOHsrNy7SrrU5NdgvCFPHl14Py5rxu4QZW8EF5km6SqJYj9MhrDsEm
wJ/ZM3Zbaj98MAls7pulHxabMo8hvGfMSmcNOFfgh7yqCm5eu8gNnt/LbLaB9IvI
v46ZGNvnpbtkWgk4Eaq+v3Y5/+4CoUfuAFn7K21SHNcgzDbhE3Ii6cam/rwPeCdn
a+LcDLzeDQpnnYKukx7Zyk7Z+FblXWHWZ/ClLcR8JgYYSrbrXxSLtRdM5EtLje2J
ZnqFKqmlMcq2OhTjBSoHSJjiOkxyz5eWWrEf7d1/oH19WSW+rv5VfZUXAkYtfGKo
OJChuIomrLNqJhAwTnxG3fnVh2NMhLwDVEjkFgvej4shCZXhoVgWu39mWnbyTxV3
57adiuVUv6AboH6Lyvi/yzV7sWmZbL/U/YVvt+Z9SEh0syy6YBb87bW3Mr1qnLeG
QF4AmF553qzHwd9uxUoFfiUoBxH1GvNmOWtx6lYKhy0lm3AwvW1XHKqsDG4KbVJg
zzok7J2yv1/1rd8dJ+8tCwyyC3WJjNjtq/ULOltugwQpqVK4PCwWAUmjJaTP3Gpp
ZH/bGuLSQWxxiinwKCkFSxwbewJu+AvtoXYKBfk/Gf5O6GyUyryBbBMO9dsqP27A
Zg3P4+ejS7RN
=sx6G
-----END PGP SIGNATURE-----
Merge tag 'pm-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These address some PCI device power management issues, add new
hardware support to the RAPL power capping driver, add HWP guaranteed
performance change notification support to the intel_pstate driver,
replace deprecated CPU-hotplug functions in a few places, update CPU
PM notifiers to use raw spinlocks, update the PM domains framework
(new DT property support, Kconfig fix), do a couple of cleanups in
code related to system sleep, and improve the energy model and the
schedutil cpufreq governor.
Specifics:
- Address 3 PCI device power management issues (Rafael Wysocki).
- Add Power Limit4 support for Alder Lake to the Intel RAPL power
capping driver (Sumeet Pawnikar).
- Add HWP guaranteed performance change notification support to the
intel_pstate driver (Srinivas Pandruvada).
- Replace deprecated CPU-hotplug functions in code related to power
management (Sebastian Andrzej Siewior).
- Update CPU PM notifiers to use raw spinlocks (Valentin Schneider).
- Add support for 'required-opps' DT property to the generic power
domains (genpd) framework and use this property for I2C on ARM64
sc7180 (Rajendra Nayak).
- Fix Kconfig issue related to genpd (Geert Uytterhoeven).
- Increase energy calculation precision in the Energy Model (Lukasz
Luba).
- Fix kobject deletion in the exit code of the schedutil cpufreq
governor (Kevin Hao).
- Unmark some functions as kernel-doc in the PM core to avoid
false-positive documentation build warnings (Randy Dunlap).
- Check RTC features instead of ops in suspend_test Alexandre
Belloni)"
* tag 'pm-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: domains: Fix domain attach for CONFIG_PM_OPP=n
powercap: Add Power Limit4 support for Alder Lake SoC
cpufreq: intel_pstate: Process HWP Guaranteed change notification
thermal: intel: Allow processing of HWP interrupt
notifier: Remove atomic_notifier_call_chain_robust()
PM: cpu: Make notifier chain use a raw_spinlock_t
PM: sleep: unmark 'state' functions as kernel-doc
arm64: dts: sc7180: Add required-opps for i2c
PM: domains: Add support for 'required-opps' to set default perf state
opp: Don't print an error if required-opps is missing
cpufreq: schedutil: Use kobject release() method to free sugov_tunables
PM: EM: Increase energy calculation precision
PM: sleep: check RTC features instead of ops in suspend_test
PM: sleep: s2idle: Replace deprecated CPU-hotplug functions
cpufreq: Replace deprecated CPU-hotplug functions
powercap: intel_rapl: Replace deprecated CPU-hotplug functions
PCI: PM: Enable PME if it can be signaled from D3cold
PCI: PM: Avoid forcing PCI_D0 for wakeup reasons inconsistently
PCI: Use pci_update_current_state() in pci_enable_device_flags()
HiSilicon KunPeng920 and KunPeng930 have devices that appear as PCI but are
actually on the AMBA bus. These fake PCI devices can support SVA via the
SMMU stall feature.
DT systems can indicate this in the device tree, but ACPI systems don't
have that mechanism, so add a "dma-can-stall" property manually for them.
[bhelgaas: add text from Robin as comment near quirk]
Link: https://lore.kernel.org/r/1626144876-11352-4-git-send-email-zhangfei.gao@linaro.org
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Add a driver for the DesignWare-based PCIe controller found on
RK356X. The existing pcie-rockchip-host driver is only used for
the Rockchip-designed IP found on RK3399.
Link: https://lore.kernel.org/r/20210625065511.1096935-1-xxm@rock-chips.com
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Simon Xue <xxm@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Rob Herring <robh@kernel.org>
As part of code refactoring completed in a0fd361db8 ("PCI: dwc: Move
"dbi", "dbi2", and "addr_space" resource setup into common code"),
dw_plat_add_pcie_ep() was removed and the call to the dw_pcie_ep_init() was
moved into dw_plat_pcie_probe().
This left a break statement behind that is not needed any more as as
dw_plat_pcie_probe() returns immediately after calling dw_pcie_ep_init().
Remove this surplus break statement that became dead code.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20210701210252.1638709-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The switch statement in the artpec6_pcie_probe() has a local code block
where "val" is defined and immediately used by the artpec6_pcie_readl().
This extra code block adds brackets at the same indentation level as the
switch statement itself which can hinder readability of the code.
Move the "val" declaration to the top of the function and remove
the extra code block from the switch statement.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20210701204401.1636562-2-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
As part of code refactoring completed in a0fd361db8 ("PCI: dwc: Move
"dbi", "dbi2", and "addr_space" resource setup into common code"),
artpec6_add_pcie_ep() was removed and the call to the dw_pcie_ep_init()
was moved into artpec6_pcie_probe().
This left a break statement behind that is not needed any more as
artpec6_pcie_probe() returns immediately after calling dw_pcie_ep_init().
Remove this surplus break statement that became dead code.
Link: https://lore.kernel.org/r/20210701204401.1636562-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
