These are common headers used in FM submodules (FM V4L2,
FM common, FM Rx,and FM TX).
Signed-off-by: Manjunatha Halli <manjunatha_halli@ti.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
get_user_pages() may return -errno, such as -EFAULT. So don't blindly use
its return value as an offset into dma->map[] for the next get_user_pages()
call. Since we'll give up and return an error if either fails, don't even
make the second call if the first failed to give us exactly what we were
looking for.
The old code would also call put_page() on as many elements of dma->map[]
as we'd asked for, regardless of how many were valid.
[Andy Walls modified this patch to return -EFAULT instead of -EINVAL
as Paul's observation "I'm not sure -EINVAL is the best return code vs
-EFAULT or -ENOMEM, [...]" was correct. The return value bubbles up
as a return code for write(), for which the V4L2 API spec indicates
EINVAL is incorrect and EFAULT is correct.]
Signed-off-by: Paul Cassella <fortytwo-ivtv@maneteren.bigw.org>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the first, botched attempt at preventing direct use of a user pointer in
ivtv_write_vbi().
Reported-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
get_user_pages() may return fewer page than we ask for. As we give up and
return an error in this case, we need to put_page() each of the pages we
did get.
[Andy Walls modified the patch, only removing the braces in the 'for'
statement, to eliminate a checkpatch warning.]
Signed-off-by: Paul Cassella <fortytwo-ivtv@manetheren.bigw.org>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ivtvfb is now in the kernel, so stop saying it's not.
Signed-off-by: Paul Cassella <fortytwo-ivtv@manetheren.bigw.org>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All necessary parameters already stored in frontend cache.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Variable 'retune' does not make sense.
Loop is not needed for only one try.
Remove unnecessary dprintk's.
Remove a lot of debug messages and delays.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The card consists of a PCI-e to USB Host Controller and
two TeVii S660 equivalent cards.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are two TeVii s660 modifications with different LNB power control
implementations. It is safe to call both methods for each card.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
RC keys structure for Prof 1100 already defined, so remove extra initialization.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Code changed for dw2102, stv0900 in order to achieve that.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
MarkusF wrote:
I accidently got a Terratec Cinergy S2 USB HD (instead of a Terratec Cinergy S2 PCI HD).
I found in the windows driver, that the driver is for the usb ids:
0CCD:00A8
1F4D:3000
The dvb-s2 usb adapter has the id 0CCD-00A8.
So I patches your driver and added the usb id, where the 1F4D:3000 is
and it worked (after I downloaded the firmware dvb-fe-ds3000.fw).
w_scan found the channels and vdr is working fine.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Before this patch we can use only one card type from list due to
sharing one firmware name. Now it's fixed.
Also driver tries to attach only appropriate demod for this cards.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In drivers/media/dvb/ttusb-budget/dvb-ttusb-budget.c:ttusb_boot_dsp() we
need to call release_firmware(fw) before returning or we'll leak - no
matter if we succeed or fail.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pvrusb2: Declare closed-caption setup for line 21 - this is needed for
sliced VBI capture support. (However none of that works right now
anyway.)
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pvrusb2: The origin of the capability bounds rectangle may differ from
(left=0,top=0) so the calculation should use absolute coordinates,
here below, or use relative coordinates like
cropl_val-cap->bounds.left and cropt_val-cap->bounds.top.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pvrusb2: Recognize and handle mode change before dealing with changes
related to the video standard. Even though the video standard should
only matter when in analog mode, doing this way is technically cleaner
in case there's other stuff that might depend on both.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This tuner PLL has missing initialisation settings resulting in
haphazard tuning. The PLL LPF was set to just 22000 symbol rate.
Basically, the module is a Sharp BS2F7HZ0194 (STV0299+IX2410)
I have had problems implementing the PLL in a new driver and
did not want to break the IX2410 out of the PLL.
This applies to DW2102, DM1105, CX88 and OPERA1 drivers.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the drivers/ieee1394/ backend was removed from firedtv, its I/O no
longer needs to be abstracted as exchangeable backend methods.
Also, ieee1394 variants of module and device probe and removal are no
longer there. Move module probe and removal into firedtv-fw.c where
device probe and removal are implemented.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changes:
Add function tm6000_set_reg_mask for change some bits in regs. Very usefull, simplify some code with this function.
Add control mute
Add control volume
Add control audio input MUX
Add support radio
Radio works well. TV works too
Known bugs:
The programm gnomeradio can't set freq for radio, it use old v4l API. Audio over USB works via arecord.
The programm mplayer can set freq but no any audio
mplayer -v -rawaudio rate=48000 radio://105.2/capture driver=v4l2:alsa:adevice=hw.1,0:amode=1:audiorate=48000:forceaudio:immediatemode=0
When start watch TV very shortly after radio the kernel crashed hardly. Didn't stop all USB URBs, need some time for stop.
[mchehab@redhat.com: fix merge conflicts]
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for Terratec Grabster AV 150/250 MX. For now it is
only possible to use composite input as switching inputs does not work.
[mchehab@redhat.com: Fix merge conflicts and simplify board entries]
Signed-off-by: Holger Nelson <hnelson@hnelson.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add two new TV cards of Beholder.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Speed up tuning, as firmware is not necessary to load every attempt to tune
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Decrease firmware loading time. Before it is ~4000 i2c calls,
now it is ~256 i2c calls to load ds3000 firmware.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
TeVii s480 works fine with that on DVB-S2 channels
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make some initializations in init, not in tune function
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds audio DMA capture and ALSA mixer elements for the line
input jack of the Hauppauge Nova-S-plus DVB-S PCI card. The Nova-S-plus
has a WM8775 ADC that is currently not detected. This patch enables
this chip and exports volume, balance mute and ALC elements for ALSA
mixer controls.
[mchehab@redhat.com: Changed the patch to only talk with wm8775 if board
info says so. Also, added platform_data support, to avoid changing the
behaviour for other boards, and fixed CodingStyle]
[awalls@md.metrocast.net: Changed patch to make the WM8775_GID defintion
bridge driver private and let the bridge driver set the value of
v4l2_subdev.grp_id.]
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Add one more radio input, usefull for tm6010
Add control output amplitude.
Add set_config function for configure tuner when TV card hasn't dvb part.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add linux/sched.h because of missing declaration of TASK_NORMAL.
This patch fixes the following error:
drivers/media/video/omap24xxcam.c: In function
'omap24xxcam_vbq_complete':
drivers/media/video/omap24xxcam.c:415: error: 'TASK_NORMAL' undeclared
(first use in this function)
drivers/media/video/omap24xxcam.c:415: error: (Each undeclared
identifier is reported only once
drivers/media/video/omap24xxcam.c:415: error: for each function it
appears in.)
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes the warning "Using plain integer as NULL pointer",
generated by sparse, by replacing
if (var == 0)
with
if (!var)
after an allocation
and all other offending 0s with NULL.
KernelVersion: linus' tree-1f0324c
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cxhdl->priv field was not set initially, only after capturing started.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It takes too long time to scan due to low symbol rate PID's
like PAT, PMT, CAT, NIT.
For that matter we enabled permanently all PID's
less 0x20 in hardware PID filter for NetUP Dual DVB-T/C CI RF card
to combine rates.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is needed for multifrontend support.
NetUP Dual DVB-T/C CI RF card has frontends connected to port B & C
Each frontend has two switchable cores - DVB-T & DVB-C
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is two external I2C buses in cx23885 chip.
Currently, analog tuners supported for second I2C bus only
In NetUP Dual DVB-T/C CI RF card tuners connected to first bus
So, in order to support analog tuners sitting on first bus
we need modifications.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The card based on cx23885 PCI-e brige. Altera FPGA for CI,
multistandard demods stv0367 from STM for QAM & OFDM, Xcieve xc5000 tuners
and additional cx25840 for second analog input.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
