Update FW version readback. IPC_GLB_GET_FW_VERSION reads back
the ABI version whilst the release version is in the mailbox.
Update to use mailbox version for info logging.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The sst-haswell-dsp.c is an ACPI independent file, this patch removes
ACPI header files for it.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This interface will be used by subsequent patches to set/get parameters from DSP
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
DSP returns error codes for IPC return so add them in driver
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
the shim registers start and end can be useful while parsing the shim addresses,
so add these
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Merge D-SRAM0 D-SRAM1 D-SRAM2 to D-SRAM, for wild cat point ADSP mem regions.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add dummy read after each block enable, to workaround
SRAM write missing bytes issue.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This change removes unsupported formats from System,
Capture and Loopback FE DAIs.
Also it fixes S24_LE support on all DAIs.
While at this fix 24 bit flag for BYT as well.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Kernel should not enable/disable speakers and digital microphone whenever
jack is inserted/removed. This is more use-case than kernel specific
decision. For instance one may want to play VoIP ring tones using both
speakers and headphone but play music only from one of them.
Because of above reason remove "Ext Spk" and "Int Mic" update when jack
state is changed. Also this update was illogical anyway: "Ext Spk" was
enabled when jack was inserted and disabled when jack was removed.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
It turned out there is no need to enable microphone detection in MAX98090
codec. Headset microphone is anyway detected by a GPIO signal from another
chip and headset button presses cannot be detected either because a signal
needed for it is not connected.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pass actual jack type bitmask to snd_soc_jack_new() in order to report
also microphone detections and not only headphone. While at it change also
jack name and pass also SND_JACK_LINEOUT type.
Reported-by: Jin Yao <yao.jin@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Headset jack has only mono microphone input.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Mic detect GPIO is active low when headset microphone is detected. Found
both by debugging and checking the schematics.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move "MICBIAS" as a supply widget to "Headset Mic" instead of keeping it
between input pin "IN34" and "Headset Mic".
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As added in previosu patch along with stream to piep conversion si required for
compressed audio too
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Merrifield DSP used various pipelines to identify the streams and processing
modules. Add these defination in the pcm driver and also add a table for device
entries to firmware pipeline id conversion
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Tis will be used to add table based support for pcm front ends in subsequent
patches
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This will be used to update current driver as well as in support for the mrfld
patches
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now the DSP is capable of reporting the delay, report it to upper layers
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The argument was called mad_substream which is no longer apt as older driver
is not used anymore so rename as arg
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This helps us to handle pcm and compress ops seperately and per dai
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Connect "Headset Mic" to "MICBIAS1" supply widget of RT5640 in order to
enable bias voltage for headset microphones.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
DSP initialization complete message IPC_IA_FW_INIT_CMPLT is a large message
carrying firmware details in mailbox. Read and show those details during
init in order to be able to get that information to QA reports.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use card PM ops from ASoC core instead of defining custom PM ops here since
we are calling anyway common suspend/resume callbacks.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Simplify byt-rt5640.c and haswell.c machine drivers by using
devm_snd_soc_register_card(). Remove also needless dev_set_drvdata()
from byt_rt5640_probe() since snd_soc_register_card() does it too.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
A few files contain duplicate headers. This patch removes the second entry of
duplicate in each file under question.
There is no functional changes.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Stored DSP DMA pointer must be cleared before starting the stream since
PCM pointer callback sst_byt_pcm_pointer() can be called before pointer is
updated. In that case last position of previous stream was wronly returned.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Baytrail and Haswell SST IPC don't stop the kernel thread in error and
cleanup path thus leaving orphan kernel thread behind in such a case.
Also while at it, fix one error path in sst-haswell-ipc.c that doesn't free
hsw->msg.
[Jarkko: I edited the commit log a little]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add machine driver and ACPI probing for Baytrail SST with MAX98090 codec.
Jack detect code from Kevin Strasser <kevin.strasser@intel.com>, GPIO
resolving from Mika Westerberg <mika.westerberg@linux.intel.com> and fixes
and cleanups from Liam Girdwood <liam.r.girdwood@linux.intel.com>.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This makes sure a format string can never get processed into the worker
thread name from the device name.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In some cases the pcm stream is closed while context has been
scheduled to be restored, causing a null pointer deref panic.
Cancel work to ensure stream does not get freed while work is
still active/pending.
Also, restoring the pcm context can be safely skipped after the
stream has been stopped. Check if pcm stream is still running
before restoring stream context to help pending work finish
more quickly in stream close path.
Signed-off-by: Kevin Strasser <kevin.strasser@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
ALSA SoC core marks widgets as connected by default when they are
initialized in snd_soc_dapm_new_control() so there is no need to call
snd_soc_dapm_enable_pin() from machine driver init functions.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
ALSA SoC core takes care of calling snd_soc_dapm_sync() at the end
snd_soc_instantiate_card() so there is no need to call it from machine
driver init functions.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As we already have a memeber struct snd_sst_params.codec to fill this.
so removing duplicate instance
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds the support to implement drain_notify in Intels mfld driver
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This reverts commit 0cac6fc3eb.
This comiit was dropped from rev2 and would not be required as it renames the
platform ops as well which is not required.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
I managed to drop a change to stream ID setting from commit 49fee17816
("ASoC: Intel: Only export one Baytrail DAI") leading to non-working
simultaneous capture-playback since after one DAI conversion
rtd->cpu_dai->id + 1 will be the same for both playback and capture.
Use substream->stream + 1 like it was in original Liam's patch.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We don't need more than one DAI for Baytrail SST. Usage becomes also more
straightforward by grouping playback and capture streams under the same PCM
device.
[Jarkko: I made Liam's sst-baytrail-pcm.c change a few lines smaller and
squashed together with my byt-rt5640.c change]
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Prepare for single Baytrail DAI playback/capture link by accessing PCM data
using stream ID instead of rtd->dev. Now rtd->dev is unique for playback
and capture since they are exported as separate DAIs but not once converted
to single DAI.
[Jarkko: Separated from another commit with updated commit log]
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 10df350977 ("ASoC: Intel: Fix Audio DSP usage when IOMMU is
enabled.") caused following regression in Baytrail SST:
baytrail-pcm-audio baytrail-pcm-audio: error: DMA alloc failed
baytrail-pcm-audio baytrail-pcm-audio: error: failed to load firmware
Fix this by calling dma_coerce_mask_and_coherent() in sst_byt_init() with
the same dma_dev device what is now used in sst_fw_new() when allocating the
DMA buffer.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This follows the same idea than commit 10df350977
("ASoC: Intel: Fix Audio DSP usage when IOMMU is enabled.") by using only
ACPI device for all DMA allocations. Since DMA masking is already done in
firmware loading it can be removed from here.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since there is no support for compressed audio in Baytrail ADSP firmware
there is no need to leave it on during suspend since ALSA PCM buffers are
too small for leaving ADSP on for playing or recording.
Implement PM callbacks to Baytrail byt-rt5640.c machine driver that call
snd_soc_suspend and snd_soc_resume functions and unset the ignore_suspend
fields in DAI links.
This makes soc-core and ALSA core gracefully suspend and resume active
stream and call sst_byt_pcm_trigger() during suspend-resume cycle.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add suspend and resume support to Baytrail SST DSP. This is implemented by
unloading firmware modules and putting DSP into reset prior suspend and
restarting DSP again in normal boot state after resume.
Context restore for running streams is implemented by scheduling a work from
sst_byt_pcm_trigger() that will allocate a stream with existing parameters
and start it from last known buffer position before suspend.
[Jarkko: Squashed together 5 WIP patches from Liam and 1 from me]
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Suspend/resume requires reloading FW to boot state so we need to also make
sure that the driver matches the FW state at boot.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We have to save the physical address of extended firmware block in the
beginning of mailbox every time when we boot the DSP firmware since that
mailbox address is re-used after DSP firmware is running. Otherwise DSP
firmware will get bogus extended firmware block address during next DSP
boot.
Currently this is not problem but becomes when DSP runtime rebooting is
implemented. Prepare for that by moving extended firmware address saving
from sst_byt_init() to sst_byt_boot().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Stream start position will be needed in resume code. Prepare for it by
adding start offset argument to sst_byt_stream_start().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Baytrail ADSP stream IPC simplifies a little by moving IPC_IA_START_STREAM
construction and sending directly into sst_byt_stream_start() from
sst_byt_stream_operations(). This is because IPC_IA_START_STREAM is only
stream IPC with extra message data so this move saves a few code lines.
Main motivation for this is to prepare for passing stream start position
to sst_byt_stream_start() which will be needed in resume code.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is for preparing suspend/resume support but can give also more
safeguard against concurrent timestamp structure access between DSP firmware
and host.
Now DSP DMA pointer is sampled in each pcm pointer callback in
sst_byt_pcm_pointer() but that is unneeded since DSP updates the timestamp
period basis and can potentially be racy if sst_byt_pcm_pointer() is called
when DSP is updating the timestamp.
By taking DSP DMA pointer only after period elapsed IPC messages in
byt_notify_pointer() and returning stored hw pointer in
sst_byt_pcm_pointer() there is less risk for concurrent access.
The same stored hw pointer can be also used in suspend/resume code for
restarting the stream at the same position.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit 4b68b4e1c5 (ASoC: Intel: split the pcm and compress to
different files) the compressed ops haven't been built causing link
failures on allyesconfig and making the driver unbuildable. Add the
object to the Makefile to fix that.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by Vinod Koul <vinod.koul@intel.com>
this is for further updates to driver which supports DPCM :)
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
With DPCM we have media dai used and no seperate headset and speaker dai so
remove the speaker dai
The vibra is no longer supported thru audio, so remove
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For manging them and adding support for more platforms
Code move only
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
as this will be used in compressed split file in subsequent patch
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
to sst-mfld-platform-pcm.c so that we can split pcm and compress to different
files for upcoming changes to support more platforms
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add some SST API calls to unload and reload firmware modules. This can be used
by PM code to restore state and also allow modular FW to unload and release
memory blocks.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Block offset calculations are done in the contiguous allocator so
are not required here.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch fixes the following dereference check ordering.
sound/soc/intel/sst-haswell-pcm.c:749 hsw_pcm_probe() warn: variable dereferenced before check 'pdata' (see line 746)
git remote add asoc git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git
git remote update asoc
git checkout 0b708c87f6
vim +/pdata +749 sound/soc/intel/sst-haswell-pcm.c
a4b12990 Mark Brown 2014-03-12 740 };
a4b12990 Mark Brown 2014-03-12 741
a4b12990 Mark Brown 2014-03-12 742 static int hsw_pcm_probe(struct snd_soc_platform *platform)
a4b12990 Mark Brown 2014-03-12 743 {
a4b12990 Mark Brown 2014-03-12 744 struct sst_pdata *pdata = dev_get_platdata(platform->dev);
a4b12990 Mark Brown 2014-03-12 745 struct hsw_priv_data *priv_data;
0b708c87 Liam Girdwood 2014-05-02 @746 struct device *dma_dev = pdata->dma_dev;
0b708c87 Liam Girdwood 2014-05-02 747 int i, ret = 0;
a4b12990 Mark Brown 2014-03-12 748
a4b12990 Mark Brown 2014-03-12 @749 if (!pdata)
a4b12990 Mark Brown 2014-03-12 750 return -ENODEV;
a4b12990 Mark Brown 2014-03-12 751
a4b12990 Mark Brown 2014-03-12 752 priv_data = devm_kzalloc(platform->dev, sizeof(*priv_data), GFP_KERNEL);
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Read the stream offset and presentation position from DSP memory rather
than using the old estimated position. This fixes timing issues with
pulseaudio.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
hw_params() can be called multiple times. Make sure we release the DSP
stream that was allocated on previous hw_params() calls before allocating
a new DSP stream.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The Intel IOMMU requires that the ACPI device is used to allocate all
DMA memory buffers. This means we need to pass the DMA device pointer into child
component devices that allocate DMA memory.
We also only set the DMA mask for the ACPI device now instead of for each
component device.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix page table creation on Haswell and Broadwell to remove unsafe
virt_to_phys mappings and use more portable SG buffer. Use audio buffer
APIs to allocate DMA buffers.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make sure we add the allocated blocks to the modules list of blocks.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make sure we dont alloc blocks twice with requests spanning more
than one block.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
I suppose there is a possibility that hsw_notification_work() may run after
sst_hsw_stream_free() which can lead to a kernel crash since struct
sst_hsw_stream is freed at that point and
stream = container_of(work, struct sst_hsw_stream, notify_work) is not valid
when hsw_notification_work() is run.
Reported-by: Derek Basehore <dbasehore@chromium.org>
Reported-by: Wenkai Du <wenkai.du@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is a race between sst_byt_stream_free() and sst_byt_get_stream()
if sst_byt_get_stream() called from sst_byt_irq_thread() context is
accessing the byt->stream_list while a stream is deleted from the list.
A stream is added to byt->stream_list in sst_byt_stream_new() and deleted in
sst_byt_stream_free(). sst_byt_get_stream() is always protected by
sst->spinlock, but the stream addition and deletion are not protected.
The patch adds spinlock to both stream addition and deletion.
[Jarkko: Same fix added to sst-haswell-ipc.c too]
Signed-off-by: Wenkai Du <wenkai.du@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There were occasional ADSP crash during reboot testing:
[ 11.883364] BUG: unable to handle kernel paging request at ffffc90121700000
[ 11.883380] IP: [<ffffffffc024d8bc>] sst_module_insert_fixed_block+0x24f/0x26d [snd_soc_sst_dsp]
[ 11.883397] PGD 7800b067 PUD 0
[ 11.883405] Oops: 0002 [#1] SMP
[ 11.886418] gsmi: Log Shutdown Reason 0x03
The virtual address, ffffc90121700000, was out of range. The virtual
address is calculated by adding LPE base address with an offset:
sst_memcpy32(dsp->addr.lpe + data->offset, data->data, data->size);
The offset is calculated in sst_byt_parse_module, by subtraction of
two virtual addresses dsp->addr.fw_ext and dsp->addr.lpe:
block_data.offset = block->ram_offset + (dsp->addr.fw_ext - dsp->addr.lpe);
These virtual addresses are assigned by kernel from ioremap:
sst->addr.lpe = ioremap(pdata->lpe_base, pdata->lpe_size);
sst->addr.fw_ext = ioremap(pdata->fw_base, pdata->fw_size);
In current driver code, offset is defined as unsigned int32:
struct sst_module_data {
...
u32 offset; /* offset in FW file */
};
Most of the time kernel assigned virtual addresses with addr.fw_ext
greater than addr.lpe. But sometimes it was the other way round.
Fix the problem by declaring offset as signed int32_t.
Signed-off-by: Wenkai Du <wenkai.du@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix an incorrect sizeof() usage in sst_hsw_stream_get_volume(). sst_dsp_read()
is called to read into a variable of type u32, but is passed sizeof(u32 *) for
argument 'size_t bytes'. Detected by Coverity: CID 1195260.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Mark Brown <broonie@linaro.org>
The intent was to say "sizeof(*pos)" and not "sizeof(pos)".
The sizeof(*pos) is 8 bytes so the bug won't show up on 64 bit systems.
The sizeof(*dx) is 172 bytes so that will be a bugfix.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove a self assignment in sst_mem_block_alloc_scratch(). When calculating
buffer sizes there is no need for statements without effect. Detected by
Coverity: CID 1195249.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix an incorrect sizeof() usage in sst_hsw_stream_get_volume(). sst_dsp_read()
is called to read into a variable of type u32, but is passed sizeof(u32 *) for
argument 'size_t bytes'. Detected by Coverity: CID 1195260.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Mark Brown <broonie@linaro.org>
For platform controls snd_kcontrol_chip() currently returns a pointer to the
platform that registered the control. With the upcoming consolidation of
platform and CODEC controls this will change. Prepare for this by introducing
the snd_soc_kcontrol_platform() helper function that will hide the
implementation details of how the platform for a control can be obtained. This
will allow us to change this easily in the future.
The patch also updates all platforms to use this new helper function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fixes: 115f3f8 ("ASoC: mfld_machine: Convert to table based DAPM and control setup")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use table based setup to register the controls and DAPM widgets and routes.
This on one hand makes the code a bit cleaner and on the other hand
the board level DAPM elements get registered in the card's DAPM context rather
than in the CODEC's DAPM context.
The mfld_machine driver is a bit special in that it directly writes to one of
the CODEC registers from one of the control handlers. Previous to this patch it
was able to get a pointer to the CODEC from the control, since the control was
registered with the CODEC. This won't be possible anymore once the control is
registered with the card. Since there are already global variables in the driver
accessed in the same function the patch adds a global variable that holds a
pointer to the CODEC and uses that.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Quite a busy release for ASoC this time, more on janitorial work than
exciting new features but welcome nontheless:
- Lots of cleanups from Takashi for enumerations; the original API for
these was error prone so he's refactored lots of code to use more
modern APIs which avoid issues.
- Elimination of the ASoC level wrappers for I2C and SPI moving us
closer to converting to regmap completely and avoiding some
randconfig hassle.
- Provide both manually and transparently locked DAPM APIs rather than
a mix of the two fixing some concurrency issues.
- Start converting CODEC drivers to use separate bus interface drivers
rather than having them all in one file helping avoid dependency
issues.
- DPCM support for Intel Haswell and Bay Trail platforms.
- Lots of work on improvements for simple-card, DaVinci and the Renesas
rcar drivers.
- New drivers for Analog Devices ADAU1977, TI PCM512x and parts of the
CSR SiRF SoC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=C5oo
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.15' into asoc-intel
ASoC: Updates for v3.15
Quite a busy release for ASoC this time, more on janitorial work than
exciting new features but welcome nontheless:
- Lots of cleanups from Takashi for enumerations; the original API for
these was error prone so he's refactored lots of code to use more
modern APIs which avoid issues.
- Elimination of the ASoC level wrappers for I2C and SPI moving us
closer to converting to regmap completely and avoiding some
randconfig hassle.
- Provide both manually and transparently locked DAPM APIs rather than
a mix of the two fixing some concurrency issues.
- Start converting CODEC drivers to use separate bus interface drivers
rather than having them all in one file helping avoid dependency
issues.
- DPCM support for Intel Haswell and Bay Trail platforms.
- Lots of work on improvements for simple-card, DaVinci and the Renesas
rcar drivers.
- New drivers for Analog Devices ADAU1977, TI PCM512x and parts of the
CSR SiRF SoC.
Conflicts:
sound/soc/intel/Kconfig
The rt5640 driver won't compile without I2C enabled. Hence, the Intel
Haswell and Baytrail+RT5640 ASoC drivers must also depend on I2C, since
these select RT5640.
This solves:
sound/soc/codecs/rt5640.c:2220:1: warning: data definition has no type or storage class [enabled by default]
sound/soc/codecs/rt5640.c:2220:1: error: type defaults to ‘int’ in declaration of ‘module_i2c_driver’ [-Werror=implicit-int]
sound/soc/codecs/rt5640.c:2220:1: warning: parameter names (without types) in function declaration [enabled by default]
sound/soc/codecs/rt5640.c:2210:26: warning: ‘rt5640_i2c_driver’ defined but not used [-Wunused-variable]
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Update the Haswell driver to use .dai_fmt in DAI link to set the
format.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Calling "kfree(byt)" is a double free because that was allocated with
devm_kzalloc(). There were a couple places which leak "byt->msg". That
memory is allocated in msg_empty_list_init().
Fixes: f7d01fd675 ('ASoC: Intel: Add Intel Baytrail SST DSP IPC support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some kernel configurations can cause following build error:
sound/soc/intel/sst-baytrail-ipc.c: In function ‘sst_byt_get_dsp_position’:
sound/soc/intel/sst-baytrail-ipc.c:744:2: error: implicit declaration of function ‘memcpy_fromio’ [-Werror=implicit-function-declaration]
memcpy_fromio(&fw_tstamp,
^
cc1: some warnings being treated as errors
Fix this by including <linux/io.h> explicitly.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Setting static DAI format has been supported in the soc-core quite some time
now so there is no need to set it runtime in machine driver.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Liam Girdwoood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use more sensible kcontrol names than "Int Mic" and "Ext Spk". Speakers
especially are usually integrated devices in sales models.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Liam Girdwoood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This should be sizeof(pos) instead of sizeof(&pos). Most likely they
are both 8 bytes though so it doesn't often make a difference in real
life.
Fixes: 2298124358 ('ASoC: Intel: Add Haswell/Broadwell IPC')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This should be spin_unlock_irqrestore() instead of spin_unlock()
Fixes: 2298124358 ('ASoC: Intel: Add Haswell/Broadwell IPC')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There were some curly braces intended here, but the code actually
works the same either way so it's not a bug.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
I swear I tested missing firmware in commit e5161d7987 ("ASoC: Intel:
sst-acpi: Request firmware before SST platform driver probing").
Unfortunately same wasn't done in commit 6dda27cbbd ("ASoC: Intel:
sst-acpi: Add support for multiple machine drivers per platform") which
will cause NULL pointer dereference in sst_acpi_fw_cb() when printing the
error since sst_acpi->mach is not set.
Fix this obvious error by setting the sst_acpi->mach in sst_acpi_probe().
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Enable build support for Baytrail SST DSP platform and byt-rt5640 machine
drivers.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add Baytrail SST descriptor with the byt-rt5640 machine driver to sst-acpi
loader.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add machine driver for Baytrail SST DSP platform with RT5640 audio codec.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This adds the Baytrail SST DSP PCM platform driver. It registers itself with
the ALSA SoC layer and uses Intel Baytrail SST DSP IPC for DSP control.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for Baytrail SST DSP IPC. This provides mechanism to communicate
with the DSP firmware.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This adds basic functionality for Baytrail SST DSP initialization and
firmware loading.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
While the SHIM register addresses in Baytrail are the same than Haswell and
Broadwell their register size is 64-bit and some bits are different.
This patch adds the SST device ID for Baytrail and Baytrail specific
SHIM bit definitions.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for Haswell based machines with SST DSP audio.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Build the Haswell/Broadwell PCM, IPC and DSP drivers.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add the Haswell and Broadwell PCM DSP platform driver. This driver uses
the IPC driver for communication with the SST DSP.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for Haswell and Broadwell DSP IPC. This is used by the DSP
platform PCM driver to configure the DSP for audio operations.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for low level differentiation functions for Haswell and Broadwell
SST DSPs. This includes suppoprt for DSP boot and reset, DSP firmware module
parsing and DSP memory block map initialisation.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The pin updates in this driver look like they are intended to be done
atomically, update to do so.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Disable build on non X86 architectures except for compile testing. This fixes
the following build errors on PPC and adds an option for testing the build on other
architectures as suggested by Mark Brown :-
sound/soc/intel/sst-dsp.c: In function 'sst_dsp_outbox_write':
sound/soc/intel/sst-dsp.c:218:2: error: implicit declaration of function 'memcpy_toio' [-Werror=implicit-function-declaration]
memcpy_toio(sst->mailbox.out_base, message, bytes);
^
sound/soc/intel/sst-dsp.c: In function 'sst_dsp_outbox_read':
sound/soc/intel/sst-dsp.c:231:2: error: implicit declaration of function 'memcpy_fromio' [-Werror=implicit-function-declaration]
memcpy_fromio(message, sst->mailbox.out_base, bytes);
^
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Initial implementation of this driver focused only matching SST ACPI ID
with single machine driver and same firmware file per platform. It was known
restriction to be improved incrementally.
This patch is now changing this that SST ACPI ID refers purely to platform
specific data which refers to machine drivers on this platform, not vice
versa.
Matching machine driver is found by looking at ACPI ID which would best
match with the driver. Typically this would be the ACPI ID of audio codec
but is not tied to it.
This patch also changes that DSP firmware name is machine not platform
specific.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We originally thought to request SST audio DSP firmware during the SST
platform driver initialization. However plain request_firmware doesn't
work in driver probe paths if userspace is not ready to handle it. For
instance when drivers are built-in.
Implementing asynchronous firmware request in SST platform driver
initialization complicates code needlessly since it anyway will fail if
firmware is missing.
This is more simple to handle by requesting firmware asynchronously in
sst_acpi_probe() and register SST platform only after firmware is loaded.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move fw_base and fw_size fields in struct sst_pdata under ACPI data for
clarifying that these are not related to firmware file but for platform
specific extended firmware area reserved by the BIOS.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The Intel audio DSP SST trace event header has been renamed from sst.h
to intel-sst.h in order to avoid any confusion with any future
Samoa Standard Time drivers ;)
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add GFP_KERNEL when allocating firmware DMA buffer.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This adds kernel build support for Intel SST core audio.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Provide services for Intel SST drivers to load SST modular firmware.
SST Firmware can be made up of several modules. These modules can exist
within any of the compatible SST memory blocks. Provide a generic memory
block and firmware module manager that can be used with any SST firmware
and core.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Most of the SST devices will be exposed as ACPI devices. It makes sense to
avoid duplication of the driver enumeration logic and concentrate the functionality
into a single ACPI SST enumeration file.
Idea of this loader is to parse data we get from ACPI and to be able to load
needed other SST drivers and ASoC machine driver runtime based on single
ACPI ID what BIOS gives to us.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for Intel Smart Sound Technology (SST) audio DSPs.
This driver provides the low level IO, reset, boot and IRQ management
for Intel audio DSPs. These files make up the low level part of the SST
audio driver stack and will be used by many Intel SST cores like
Haswell, Broadwell and Baytrail.
SST DSPs expose a memory mapped region (shim) for config and control.
The shim layout is mostly shared without much modification across cores
and this driver provides a uniform API to access the shim and to enable
basic shim functions. It also provides functionality to abstract some shim
functions for cores with different shim features.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Resent with correct email for Mark.
In order to differentiate the different Intel SST audio core drivers we
need to rename the current drivers with a mfld prefix. This also includes
renaming in the Makefile and Kconfig
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
We have other Intel platforms coming having the Smart Sound Technology (SST)
so rename the mid-x86 directory to intel as originally directory name
reflected only Intel MID platform.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
