This patch adds driver for Samsung S5K4ECGX image sensor with an
embedded SoC ISP. The driver only implements preview operation mode
and still capture (snapshot) and face detection features are missing
now. Following controls are supported: contrast, saturation,
brightness, sharpness.
Signed-off-by: Sangwook Lee <sangwook.lee@linaro.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
New mem-to-mem video drivers should use V4L2_CAP_VIDEO_M2M capability, rather
than ORed V4L2_CAP_VIDEO_CAPTURE and V4L2_CAP_VIDEO_OUTPUT flags, as outlined
in commit a1367f1b26.
Acked-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
channel_first_int[][] variable is used as a flag for the ISR,
This flag was being set after enabling the interrupts, There
where situations when the isr occurred even before the flag was set
dues to which it was causing the application hang.
This patch sets channel_first_int[][] flag just before enabling the
interrupt.
Reported-by: David Oleszkiewicz <doleszki@adsyscontrols.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes a failure in vb2_qbuf in user pointer mode where
__qbuf_userptr checks if the buffer queued by userspace is large
enough. The failure would happen if coda_queue_setup was called
with empty fmt (and thus set the expected buffer size to the maximum
resolution), and userspace queues buffers of smaller size -
corresponding to the negotiated dimensions - were queued.
Explicitly setting sizeimage to the value negotiated via s_fmt
fixes the issue.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The hardware can also rotate in 90° steps, but there is no
corresponding V4L2_CID defined yet.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While the CODA is running a PIC_RUN command, its registers are
not to be touched.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
USERPTR buffer support is provided by the videobuf2 framework.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a 1 second timeout for each PIC_RUN command to the CODA. In
case it locks up, stop all queues and dequeue remaining buffers.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Determining the next free instance just by incrementing and decrementing
an instance counter does not work: if there are two instances opened,
0 and 1, and instance 0 is released, the next call to coda_open will
create a new instance with index 1, but instance 1 is already in use.
Instead, scan a bitfield of active instances to determine the first
free instance index.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
job_ready is supposed to signal whether a context is ready to be
added to the job queue, not whether the CODA is ready to run it
immediately.
Calling v4l2_m2m_job_finish at the end of coda_irq_handler already
guarantees that the coda is ready when v4l2-mem2mem eventually tries
to run the next queued job.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some codecs running on CODA need internal framebuffers for reference and
reconstructed frames. Allocate them separately, and do not use the input
vb2_buffers: those will be handed off to userspace regularly, and there
is no way to signal to the CODA which of the registered framebuffers are
off limits. As a consequence, userspace is now free to choose the number
of v4l2 buffers.
This patch also includes the code to set up the parameter buffer for
CODA7 and above with 64-bit AXI bus width.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Javier Martin <javier.martin@vista-silicon.com>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This uses the ARCH_MXC specific iram_alloc API to allocate a work
buffer in the SoC's on-chip SRAM and sets up the AXI_SRAM_USE
register. In the future, the allocation will be converted to use
the genalloc API.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for loading a raw firmware with 16-bit chars ordered in
little-endian 64-bit words, corresponding to the memory access pattern
of CODA7 and above: When writing the boot code into the code download
register, the chars have to be reordered back.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
New mem-to-mem video drivers should use V4L2_CAP_VIDEO_M2M capability, rather
than ORed V4L2_CAP_VIDEO_CAPTURE and V4L2_CAP_VIDEO_OUTPUT flags, as outlined
in commit a1367f1b26.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Acked-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Check against q->fileio to see if the queue owner should be set or not.
The former check against the return value of read or write is wrong, since
read/write can return an error, even if the queue is in streaming mode.
For example, EAGAIN when in non-blocking mode.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This makes it easier to read and also ties in more closely with the
profile concept.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ioctl validity checks have been improved and now take vfl_type
and vfl_dir into account.
During the 2012 Media Workshop it was decided that these improved
v4l2 core checks should be added as they simplified drivers and
made drivers behave consistently.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These will be used by v4l2-dev.c to improve ioctl checking.
I.e. ioctls for capture should return -ENOTTY when called for
an output device.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Write-only ioctls should have a const argument in the ioctl op.
Do this conversion for vidioc_s_crop.
Adding const for write-only ioctls was decided during the 2012 Media Workshop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Write-only ioctls should have a const argument in the ioctl op.
Do this conversion for vidioc_s_modulator.
Adding const for write-only ioctls was decided during the 2012 Media Workshop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Write-only ioctls should have a const argument in the ioctl op.
Do this conversion for vidioc_s_audout.
Adding const for write-only ioctls was decided during the 2012 Media Workshop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Write-only ioctls should have a const argument in the ioctl op.
Do this conversion for vidioc_s_audio.
Adding const for write-only ioctls was decided during the 2012 Media Workshop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Write-only ioctls should have a const argument in the ioctl op.
Do this conversion for vidioc_(un)subscribe_event.
Adding const for write-only ioctls was decided during the 2012 Media Workshop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Write-only ioctls should have a const argument in the ioctl op.
Do this conversion for vidioc_s_freq_hw_seek.
Adding const for write-only ioctls was decided during the 2012 Media Workshop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Write-only ioctls should have a const argument in the ioctl op.
Do this conversion for vidioc_s_jpegcomp.
Adding const for write-only ioctls was decided during the 2012 Media Workshop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Write-only ioctls should have a const argument in the ioctl op.
Do this conversion for vidioc_s_fbuf.
Adding const for write-only ioctls was decided during the 2012 Media Workshop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While the documentation says that VIDIOC_CROPCAP is compulsory for
all video capture and output devices, in practice VIDIOC_CROPCAP is
only implemented for devices that can do cropping and/or scaling.
Update the documentation to no longer require VIDIOC_CROPCAP if the
driver does not support cropping or scaling or non-square pixels.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It was not entirely obvious that the sequence count should also
be set for output devices. Also made it more explicit that this
sequence counter counts frames, not fields.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Video Standard section contains some awkward language. It also wasn't
updated when the error code for unimplemented ioctls changed from EINVAL
to ENOTTY.
[mchehab@redhat.com: remove a misplaced footnote tag]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These have been replaced by new defines without the "CUSTOM_" part.
Get rid of the old ones.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 'custom' timings are no longer just for custom timings, but also for standard
CEA/VESA timings. So rename to V4L2_IN/OUT_CAP_DV_TIMINGS.
The old define is still kept for backwards compatibility.
This decision was taken during the 2012 Media Workshop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently the core code looks at tvnorms to see whether ENUMSTD
or G_PARM should be enabled. This is not a good check for drivers
that support the STD API on one input and the DV Timings API on another.
In that case tvnorms may be 0.
Instead check whether s_std is present (for ENUMSTD) or whether g_std or
current_norm is present for g_parm.
Also, in the enumstd core function return ENODATA if tvnorms is 0,
because in that case the current input does not support the STD API
and ENUMSTD should return ENODATA for that.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ENODATA should be returned if the API used for getting, changing, querying
or enumerating the current video timings is not supported by the current input
or output.
This was decided during the 2012 Media Workshop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A number of old drivers still had the experimental tag. Time to remove it.
It concerns the following drivers:
VIDEO_TLV320AIC23B
USB_STKWEBCAM
VIDEO_CX18
VIDEO_CX18_ALSA
VIDEO_ZORAN_AVS6EYES
DVB_USB_AF9005
MEDIA_TUNER_TEA5761
VIDEO_NOON010PC30
This decision was taken during the 2012 Media Workshop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As per decision taken during the 2012 Media Workshop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2_BUF_TYPE_PRIVATE was used in these driver for internal purposes.
It turned out though that it wasn't used at all, so it could be removed.
I know it was used in the past, but clearly later changes made this
obsolete.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This buffer type isn't used at all, and since it is effectively undefined
what it should do it is deprecated. The define still exists, but any
internal support for such buffers is removed.
The decisions to deprecate this was taken during the 2012 Media Workshop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
During the 2012 Media Workshop it was decided that bus_info as returned
by VIDIOC_QUERYCAP can no longer be empty. It should be a unique identifier,
and empty strings are obviously not unique.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- S/TRY_FMT should always succeed, unless an invalid type field is passed in.
- TRY_FMT should give the same result as S_FMT, all other things being equal.
- ENUMFMT may return different formats for different inputs or outputs.
This was decided during the 2012 Media Workshop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Specify that STREAMON/OFF should return 0 if the stream is already
started/stopped.
The spec never specified what the correct behavior is. This ambiguity
was resolved during the 2012 Media Workshop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
During the 2012 Media Workshop it was decided to split off the control
definitions into their own v4l2-controls.h header, included by videodev2.h.
Because controls make up such a large part of V4L2 they made it hard
to read videodev2.h. Splitting off the control definitions makes life
easier.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove experimantal tag from the following API elements:
V4L2_BUF_TYPE_VIDEO_OUTPUT_OVERLAY buffer type.
V4L2_CAP_VIDEO_OUTPUT_OVERLAY capability flag.
VIDIOC_ENUM_FRAMESIZES IOCTL.
VIDIOC_ENUM_FRAMEINTERVALS IOCTL.
VIDIOC_G_ENC_INDEX IOCTL.
VIDIOC_ENCODER_CMD and VIDIOC_TRY_ENCODER_CMD IOCTLs.
VIDIOC_DECODER_CMD and VIDIOC_TRY_DECODER_CMD IOCTLs.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
