- Explicitly state that the most significant n bits are zeroed on 10 and
12 bpp formats.
- Remove extra comma from the last entry of the format list
- Add a missing colon before a list
- Use figures versus word numerals consistently
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The number of high order bits in samples was documented to be 6 for 12-bit
data. This is clearly wrong, fix it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The 10-bit packed raw bayer format documented that the data of the first
pixel of a four-pixel group was found in the first byte and the two
highest bits of the fifth byte. This was not entirely correct. The two
bits in the fifth byte are the two lowest bits. The second pixel occupies
the second byte and third and fourth least significant bits and so on.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Aviv Greenberg <aviv.d.greenberg@intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As reported by smatch:
drivers/media/platform/pxa_camera.c: In function 'pxa_dma_start_channels':
drivers/media/platform/pxa_camera.c:457:21: warning: variable 'active' set but not used [-Wunused-but-set-variable]
struct pxa_buffer *active;
^~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Allow building this driver if COMPILE_TEST is set.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is a tiny fix for a switch case which quiets 2 checkpatch harmless
warnings. The generated code is not affected.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As the conversion to a v4l2 standalone device is finished, move
pxa_camera one directory up and finish severing any dependency to
soc_camera.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of the legacy behavior where it was required to wait for all
video buffers to be finished by the hardware, use a cancel like strategy
: as soon as the stop_streaming() call is done, abort all DMA transfers,
report the already buffers as failed and return.
This makes stop_streaming() more a "cancel capture" than a "wait for end
of capture" semantic.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch removes the soc_camera API dependency from pxa_camera.
In the current status :
- all previously captures are working the same on pxa270
- the s_crop() call was removed, judged not working
(see what happens soc_camera_s_crop() when get_crop() == NULL)
- if the pixel clock is provided by then sensor, ie. not MCLK, the dual
stage change is not handled yet.
=> there is no in-tree user of this, so I'll let it that way
- the MCLK is not yet finished, it's as in the legacy way,
ie. activated at video device opening and closed at video device
closing.
In a subsequence patch pxa_camera_mclk_ops should be used, and
platform data MCLK ignored. It will be the sensor's duty to request
the clock and enable it, which will end in pxa_camera_mclk_ops.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is to be seen as a regression as the set_selection (former
set_crop) function is removed. This is a temporary situation in the v4l2
porting, and will have to be added later.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make all print consistent by always using :
- dev_xxx(pcdev_to_dev(pcdev), ....)
This prepares the soc_camera adherence removal by making these call rely
on only pcdev, and not the soc_camera icd structure.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Introduce sensor_call(), which will be used for all sensor invocations.
This is a preparation move to v4l2 device conversion, ie. soc_camera
adherence removal.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move the functions in the file to be regrouped into meaningful blocks :
1. pxa camera core handling functions, manipulating the herdware
2. videobuf2 functions, dealing with video buffers
3. video ioctl (vidioc) related functions
4. driver probing, removal, suspend and resume
This patch doesn't modify a single line of code.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Convert pxa_camera from videobuf to videobuf2.
As the soc_camera was already compatible with videobuf2, the port is
quite straightforward.
The special case of this code in which the vb2 to prepare is "too
big" in terms of size for the new capture format, the pxa_camera will
fail.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As the mt9m111 is now working as a standalone v4l2 subdevice sensor,
move it out of soc_camera directory and sever its dependency on
soc_camera.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
mt9m111 being a camera sensor, its colorspace should always be SRGB, for
both RGB based formats or YCbCr based ones.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove the soc_camera adherence. Mostly the change removes the power
manipulation provided by soc_camera, and instead :
- powers on the sensor when the s_power control is activated
- powers on the sensor in initial probe
- enables and disables the MCLK provided to it in power on/off
This patch also drops support for inverters on synchronisation and clock
lines. It is assumed, if any board ever needs such inverters, support
for them can be added in the future
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add entry for the HVA driver to the MAINTAINERS file.
Signed-off-by: Jean-Christophe Trotin <jean-christophe.trotin@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds the H.264 video encoding capability in the V4L2 HVA
video encoder driver for STMicroelectronics SoC (hva-h264.c).
The main supported features are:
- profile: baseline, main, high, stereo high
- level: up to 4.2
- bitrate mode: CBR, VBR
- entropy mode: CABAC, CAVLC
- video aspect: 1x1 only
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Signed-off-by: Jean-Christophe Trotin <jean-christophe.trotin@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds V4L2 HVA (Hardware Video Accelerator) video encoder
driver for STMicroelectronics SoC. It uses the V4L2 mem2mem framework.
This patch only contains the core parts of the driver:
- the V4L2 interface with the userland (hva-v4l2.c)
- the hardware services (hva-hw.c)
- the memory management utilities (hva-mem.c)
This patch doesn't include the support of specific codec (e.g. H.264)
video encoding: this support is part of subsequent patches.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Signed-off-by: Jean-Christophe Trotin <jean-christophe.trotin@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There is a warning there, because it was pointing to a different
name. Fix it.
While here, use struct &foo, instead of &struct foo.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Document vb2_ops_wait_prepare() and vb2_ops_wait_finish(),
in order to fix those two warnings:
Documentation/media/kapi/v4l2-dev.rst:166: WARNING: c:func reference target not found: vb2_ops_wait_prepare
Documentation/media/kapi/v4l2-dev.rst:166: WARNING: c:func reference target not found: vb2_ops_wait_finish
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are a few issues at the documentation: fields not documented,
bad cross refrences, etc.
Fix them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are several functions documented at the C file. Move
them to the header, as this is the one used to build the
media books.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are several small issues with the documentation. Fix them,
in order to avoid producing warnings.
While here, also make checkpatch.pl happy.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are several functions that were documented at the .c
file. As we only include the headers, we need to move them to
there, in order to have documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_m2m_dev is opaque: its meaning is only known by
v4l2-mem2mem.c. Ignore it on nitpick mode.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The kernel-doc C parser doesn't like opaque structures. So,
document it on another way.
This should get rid of this warning:
./include/media/v4l2-mem2mem.h:62: error: Cannot parse struct or union!
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Several routines are somewhat documented at v4l2-mem2mem.c
file. Move what's there to the header file.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix this warning:
Documentation/media/kapi/mc-core.rst:97: WARNING: c:func reference target not found: media_devnode_release
The media_device_release() is a function internal to media-devnode.c,
and not exported elsewhere. So, we can't cross-reference it here.
Make it explicit at the documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
One reference there is still using :ref:. Fix it, to solve this
warning:
Documentation/media/uapi/mediactl/media-ioc-g-topology.rst:236: WARNING: undefined label: media-v2-intf-devnode (if the link has no caption the label must precede a section header)
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The struct v4l2_mpeg_vbi_ITV0 is identical to struct v4l2_mpeg_vbi_itv0,
except by its size, and it is documented at the same place at the
book.
Fix cross reference for it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are several broken references there, due to the conversion to
C domain. Fix them using this shell script and manually adjust what's
broken:
# funcs is a file with the broken functions/references
for i in $(cat funcs|sort|uniq|perl -ne 'print "$1\n" if (m/(\S+)$/)'); do
i=${i//-/_}
echo $i
j=${i//_/-}
for k in $(git grep -l "_$j:" Documentation/); do
sed s,\_$j\:,"c\:type\:\: $i", <$k >a && mv a $k
done
for k in $(git grep -l "$j" Documentation/media/*.exceptions); do
sed s,$j,":c\:type\:\`$i\`", <$k >a && mv a $k
done
for k in $(git grep -l "$j" Documentation/); do
sed "s,:ref:\`$i <$j>\`,:c:type:\`$i\`," <$k >a && mv a $k
sed "s,:ref:\`$j\`,:c:type:\`$i\`," <$k >a && mv a $k
sed -E "s,:ref:\`(.*)<$j>\`,:c:type:\`\1<$i>\`," <$k >a && mv a $k
done
for k in $(git grep -l "<$j>" include/media); do
sed -E "s,:ref:\`(.*)<$j>\`,enum \&$i," <$k >a && mv a $k
done
done
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Several structs were renamed or removed during V4L2 development.
Don't try to cross-reference the legacy ones.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use C cross-references to mention the V4L2 API calls on all
places it occurs inside this file.
While here, also mark constants as such.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix those warnings:
Documentation/media/uapi/cec/cec-ioc-dqevent.rst:124: WARNING: c:func reference target not found: clock_gettime(2)
By replacing it with the right function name, using this shell script:
for i in `find Documentation/media -type f`; do sed 's,clock_gettime(2),clock_gettime,' <$i >a && mv a $i; done
Please notice that this will make the nitpick mode to shut up
complaining about that, becasue clock_gettime is on its exclude list,
but the cross reference will be undefined until someone documents
this function at the core documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The :c:type: references point to the structure name, and not to
struct foo.
Fixed via this shell script:
for i in `find Documentation/media -type f`; do perl -ne 'if (s/\:c\:type\:\`struct\s*(\S+)\`/struct :c:type:`$1`/) { s/struct\s+struct/struct/; s/(struct\s+\:c\:type\:\`\S+\`)\s+structure/$1/; } print $_' <$i >a && mv a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of using c:type:`struct foo <foo>`, use:
struct c:type:`foo`
This patch was generated via this shell script:
for i in `find Documentation/media -type f`; do perl -ne 'if (m/\:c\:type\:\`struct\s+(\S+)\s*\<(\S+)\>\`/) { $s=$1; $r=$2; if ($s eq $r) { s/\:c\:type\:\`struct\s+(\S+)\s*\<(\S+)\>\`/struct :c:type:`$2`/; s/struct\s+struct/struct/; s/(struct\s+\:c\:type\:\`\S+\`)\s+structure/$1/; }} print $_' <$i >a && mv a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
