To be able to use MC_CMD_VADAPTOR_SET_MAC, vadaptors must be
manually allocated and freed as automatic vadaptors will disappear
when their reference_count reaches zero, which must happen before
the MAC address is changed.
Vadaptors are allocated and freed in the vswitching_probe/remove
functions for PFs and VFs, and this means that vadaptors are restored
correctly following an MC reboot or other reset when required.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The parent PF creates vports for all its child VFs and adds MAC
addresses to these. When the VF driver loads, it can make an MCDI
call to get the MAC address that the parent PF assigned it.
The parent PF also assigns a mac address to its own vport because
implicit creation of a vAdaptor will only work on evb ports with
MAC addresses assigned.
The vport MAC address needs to be stored in the PF's nic_data
struct as it can later be changed on the vadaptor (and its net_dev
struct). When removing a vport the original MAC address must be
deleted.
A new flag is needed in the VF data structure to identify whether
a vport has been assigned to the VF. This is to determine whether
it needs to be un-assigned before freeing the vport. Also,
attempting to un-assign a vport which is not assigned will result
in an EALREADY error.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added efx_nic_type structure for VF.
Mapped a different BAR for VF as it uses BAR 0 for memory.
Added functions sriov_init and sriov_fini.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use MC_CMD_GET_FUNCTION_INFO to record the PF number in nic_data.
This will be needed when assigned vports to VFs.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds functions to allocate and free vswitches and vports; vadaptors
are automatically allocated and freed when TX/RX queues are
initialised and finalised. This vswitching structure is only created
if the firmware supports it, so a check that full-featured firmware
is running is performed first.
If the MC resets, the vswitching infrastructure will need to be
recreated, so mark the "must_probe_vswitching" flag when an MC reboot
is detected.
Don't try to create a vswitch if vf-count=0
This allocation of vswitches and vports does not currently support
configuring VLAN tags, but that can be added in a future change.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default port ID of EVB_PORT_ID_ASSIGNED is a "magic" number
for the MCFW to select the physical port of the PF. If other
vswitches and vports are created on top of the default firmware
configuration, the ID of the newly created vport is then required
when passed to MCDI commands. Currently, this doesn't happen so
the vport_id is never changed, but a subsequent patch will change
this behaviour so that other vswitches and vports are created.
The vport_id recorded in nic_data is only relevant for PFs.
VFs will have their vports created by their parent PF, and in
that case the parent PF will record the vport ID of each VF.
For a VF, nic_data->vport_id is expected to remain at the default
value.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The (future) code to add/remove vswitches and vports will be
dependent on the firmware variant.
To simplify the checking of the firmware variant, record
values for rx_dpcpu_fw_id and tx_dpcpu_fw_id in EF10 nic_data.
There was only one place where this was previously used:
efx_mcdi_print_fwver() in ethtool.c.
The MC_CMD_GET_CAPABILITIES can be replaced and the values from
nic_data used instead.
Note that the printing of "?" if the MC command fails or if the
outlength is incorrect no longer apply, because errors are returned
in efx_ef10_init_datapath_caps() in both of these cases.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX_DOMAIN field is currently reserved but its safer to set
it to 0 for future compatibility.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the use of sriov_configure on EF10
to enable Virtual Functions while the driver is loaded.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The efx_vf struct contains Siena-specific fields for VFs,
so rename to siena_vf.
Also move it into the siena_nic_data struct, as EF10 will
track its VFs in its own ef10_nic_data, storing much less
information about them since VFDI is no longer used.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By putting all the efx_{siena,ef10}_sriov_* declarations in
{siena,ef10}_sriov.h, ensure they cannot be called from nic-generic code.
Also fixes up an instance of this, where mcdi.c was calling
efx_siena_sriov_flr.
The single instance of netdev_ops should call general high level
functions that can then call something adapter specific in efx_nic_type.
We should only do adapter specialisation via efx_nic_type.
Removal of sriov functionality from the Falcon code means that tests
are needed for the presence of some callbacks.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn says:
====================
More Marvell DSA refactring and fixup
This patch setup continues the refactoring and cleanup of the Marvell
DSA drivers.
Patch #1 Centralizes the duplicated parts of port setup and global
setup into the shared mv88e6xxx.
Patch #2 Centralizes looping over the ports setting them up
Patch #3 Uses mnemonics for the remaining register access in the
drivers.
Patch #4 The 6172 is actually a member of the 6352 family. This moves
the probe code into the correct driver.
Patch #5 Adds more members of the 6171 family to the 6171 driver. The
new devices are untested.
Patch #6 The 6185 is a member of the 6131 family. Add it to the probe
code of the 6131 driver.
Patch #7 and Patch #8 Simply the mutex's in mv88e6xxx.c. The SMI bus
is the bottleneck, not the granularity of the mutex's so simply the
code down to a single mutex.
Patch #8 Fixes a false positive lockdep splat, due to nested uses of
MDIO busses.
Patch #9 Fixes another false positive lockdep splat with the transmit
queue because of stacked Ethernet devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA stacks an Ethernet device on top of an Ethernet device. This can
cause false positive lockdep splats for the transmit queue:
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
=============================================
[ INFO: possible recursive locking detected ]
4.0.0-rc7-01838-g70621a215fc7 #386 Not tainted
---------------------------------------------
kworker/0:0/4 is trying to acquire lock:
(_xmit_ETHER#2){+.-...}, at: [<c040e95c>] sch_direct_xmit+0xa8/0x1fc
but task is already holding lock:
(_xmit_ETHER#2){+.-...}, at: [<c03f4208>] __dev_queue_xmit+0x4d4/0x56c
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(_xmit_ETHER#2);
lock(_xmit_ETHER#2);
To avoid this, walk the tq queues of the dsa slaves and set a lockdep
class.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA can have nested MDIO busses, where the Ethernet MDIO bus is used
to access an MDIO bus within the switch which has the PHYs connected
to it. This nesting causes lockdep to give false positives. Use
mutex_lock_nested() to avoid this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SMI bus is the bottleneck in all switch operations, not the
granularity of locks. Replace the stats mutex by the SMI mutex to make
the locking concept simpler.
The REG_READ/REG_WRITE macros cannot be used while holding the SMI
mutex, since they try to acquire it. Replace with calls to the
appropriate function which does not try to get the mutex.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SMI bus is the bottleneck in all switch operations, not the
granularity of locks. Replace the PHY mutex by the SMI mutex to make
the locking concept simpler.
The REG_READ/REG_WRITE macros cannot be used while holding the SMI
mutex, since they try to acquire it. Replace with calls to the
appropriate function which does not try to get the mutex.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6185 is part of the family that the mv88e6131 driver
supports. Add it to the probe function, and set the number of ports.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6171 is one member of the family 6171/6175/6350/6351. Add the
other family members to the driver.
Not tested on these new devices.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6172 is part of the mv88e6352 family of devices. Move support
for it out of the mv88e6171 driver into the mv88e6352, which results
in some simplifications to the code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use defines for registers, shifts and bits in the remaining register
accesses in the individual drivers, in order to aid readability.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that setting up a port is identical for all switches, centralisers
the code looping over all the ports to set them up.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port setup code in the individual drivers is identical for 6123,
6171, and 6352, and very similar in 6131. Move it all into mv88e6xxx,
using the chip families to differentiate on features.
Similarly, the global setup is also very similar. Move the majority
into mv8e6xxx.
The chips themselves fall into families. Add helpers which uses the
device IDs to determine if a device is a member of a family or not.
Add some additional device IDs to the existing list, to make these
helper functions more complete. However these IDs are not yet added to
the probe functions.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces a open coded variant of a "mailbox code" definition by an
existing define, improves code readability.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds a short documentation snippet about the mailbox organization as
it's regularly not correct in freescale's datasheets.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Flexcan V10 and newer are able to receive RTR frames in a MB. Older versions
are not. Those should use flexcan in FIFO mode.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This was missed in the previous patch, add some documentation
for rate_ctrl_lock to avoid docbook warnings.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The GO_CONCURRENT regulatory definition can be extended to station
interfaces requesting to IR as part of TDLS off-channel operations.
Rename the GO_CONCURRENT flag to IR_CONCURRENT and allow the added
use-case.
Change internal users of GO_CONCURRENT to use the new definition.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Declare that MCS 0-9 are supported for all Rx chains.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, VHT capabilities and supported MCSs where set for all
bands, although VHT is only allowed on 5.2 GHz band. Fix it.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a P2P GO was allowed on a channel because of the GO concurrent
relaxation, i.e., another station interface was associated to an AP on
the same channel or the same UNII band, and the station interface
disconnected from the AP, allow the following use cases unless the
channel is marked as indoor only and the device is not operating in an
indoor environment:
1. Allow the P2P GO to stay on its current channel. The rationale behind
this is that if the channel or UNII band were allowed by the AP they
could still be used to continue the P2P GO operation, and avoid connection
breakage.
2. Allow another P2P GO to start on the same channel or another channel
that is in the same UNII band as the previous instantiated P2P GO.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, a cipher scheme can advertise an arbitrarily long
sequence counter, but mac80211 only supports up to 16 bytes
and the initial value from userspace will be truncated.
Fix two things:
* don't allow the driver to register anything longer than
the 16 bytes that mac80211 reserves space for
* require userspace to specify a starting value with the
correct length (or none at all)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For ciphers not supported by mac80211, the function currently
doesn't return any PN data. Fix this by extending the driver's
get_key_seq() a little more to allow moving arbitrary PN data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extend the function to read the TKIP IV32/IV16 to read the IV/PN for
all ciphers in order to allow drivers with full hardware crypto to
properly support this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In our department we are using some older Janz ICAN3-modules in our dekstop
pcs. There we have slightly different carrier boards than the janz-cmodio
supported in the kernel sources, called CAN-PCI2 with two submodules. But the
pci configuration regions are identical. So extending the supported pci devices
to the corresponding device ids is sufficient to get the drivers working.
* The old ICAN3-modules with firmware 1.28 need more then 250ms for the restart
after reset. I've increased the timeout to 500ms.
* The janz_ican3 module uses the raw can services of the Janz-firmware, this
means firmware must be ICANOS/2. Our ICAN3-modules are equipped with
CAL/CANopen-firmware, so I must use the appropriate commands for the layer
management services.
Te driver detects the firmware after module reset and selects the commands
matching the firmware. This affects the bus on/off-command
(ican3_set_bus_state) and the configuration of the bittiming
(ican3_set_bittiming). For better diagnostics the detected firmware string is
presented as sysfs attribute (fwinfo).
Signed-off-by: Andreas Gröger <andreas24groeger@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds documentation for the existing sysfs entries for the janz PCI
module.
Signed-off-by: Andreas Gröger <andreas24groeger@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The current definition of struct can_frame has a 16-byte size, with 8-byte
alignment, but the 3 bytes of padding are not explicit like the similar 2 bytes
of padding of struct canfd_frame. Make it explicit so it is easier to read.
Signed-off-by: Shawn Landden <shawn@churchofgit.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
VXLAN must provide the skb mark and specifiy IPPROTO_UDP when doing
the FIB lookup for the remote ip. Otherwise an invalid route might
be returned.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synchronize names with other drivers.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of_property_* calls
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use devm_* calls
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synchronize names with other drivers
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is rule for network drivers with comments blocks
which is newly checked by checkpatch.pl script.
Let's fix it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed checkpatch.pl errors and warnings.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds proper checks to handle the PHY-less case.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current implementation, jumbo frames are supported only
for the frame sizes > 16K. This patch corrects this logic to
handle jumbo frames for lesser frame sizes (< 16K) ensuring jumbo frame
MTU is within the limit of max frame size configured in the h/w
design.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packet completion interrupts for TX and RX should be serviced before
the packets are consumed. This ensures against the degenerate case when a
new completion interrupt is raised after the handler has exited but before
the interrupts are cleared. In this case its possible for the ISR to clear
an unhandled interrupt (leading to potential deadlock).
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Tested-by: Jason Wu <huanyu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AXI-DMA rx-delay interrupt can sometimes be triggered
when there are 0 outstanding packets received. This is due
to the fact that the receive function will greedily consume
as many packets as possible on interrupt. So if two packets
(with a very particular timing) arrive in succession they
will each cause the rx-delay interrupt, but the first interrupt
will consume both packets.
This means the second interrupt is a 0 packet receive.
This is mostly OK, except that the tail pointer register is
updated unconditionally on receive. Currently the tail pointer
is always set to the current bd-ring descriptor under
the assumption that the hardware has moved onto the next
descriptor. What this means for length 0 recv is the current
descriptor that the hardware is potentially yet to use will
be marked as the tail. This causes the hardware to think
its run out of descriptors deadlocking the whole rx path.
Fixed by updating the tail pointer to the most recent
successfully consumed descriptor.
Reported-by: Wendy Liang <wendy.liang@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Tested-by: Jason Wu <huanyu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the RGMII. The h/w configuration
parameter C_PHY_TYPE, which represents the interface configured in
the design, is used to differentiate various interfaces supported
by AXI Ethernet.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
