This patch makes acpi_init() exit early when ACPI is disabled.
This skips a DMI check that affects ACPI power management. The
DMI check prints a notice that is misleading when ACPI is disabled.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
For predefined method validation. Index value in warning message
could be off by one.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
If both the 32-bit and 64-bit addresses are non-null, use the
32-bit address. Provides Windows compatibility.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Use the 32-bit register addresses whenever they are non-zero. This
means that the 32-bit addresses are favored over the 64-bit
(GAS) addresses. The 64-bit addresses are only used if the 32-bit
addresses are zero. This change provides compatibility with all
versions of Windows. The worst case that this solves is when both
the 32-bit and 64-bit addresses are non-zero, but only the 32-bit
addresses are actually valid. This appears to happen in some
BIOSes because in this case, Windows uses the 32-bit addresses.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Microsoft website uses 0xCF8-0xD00. Should be 0xCF8-0xCFF (Two
32-bit registers.)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
One entry in the protected port table eliminated. Added extra
comments to describe each table entry.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Removed unused code for dump of args and locals. General cleanup
and splitting of long lines.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Affects PM1 Control register only. When reading the register, zero
the write-only bits as per the ACPI spec. ACPICA BZ 443. Lin Ming.
http://www.acpica.org/bugzilla/show_bug.cgi?id=443
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This interface is no longer necessary. Requests should be validated
on a per-field basis, not on the entire operation region.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Protect certain I/O ports from reads/writes. Provides MS
compatibility. New module, hwvalid.c
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
As per the ACPI specification, preserve (read/modify/write) all
bits that are defined as either reserved or ignored (PM control
control registers only.)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Ignored bits must be preserved according to the ACPI spec.
Usually this means a read/modify/write when writing to the
register. However, for status registers, writing a one means
clear the event. Writing a zero means preserve the event (do not
clear.) This behavior is clarified in the ACPI 4.0 spec, and the
ACPICA code now simply always writes a zero to the ignored bit.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Added a reader/writer locking mechanism to allow multiple
concurrent namespace walks (readers), but a dynamic table unload
will have exclusive access to the namespace. This fixes a problem
where a table unload could delete the portion of the namespace that
is currently being examined by a walk. Adds a new file, utlock.c
that implements the reader/writer lock mechanism. ACPICA BZ 749.
http://www.acpica.org/bugzilla/show_bug.cgi?id=749
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Incorrect register length mismatch between the 32 and 64 bit
registers in some cases. Code was was checking the wrong pointer
for non-zero, should be looking at the address within the GAS
structure.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Split long lines, update comments.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add and deploy constants for the PM status/enable/control
registers.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Cleanup table header output.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Update code for acpi_read_bit_register and acpi_write_bit_register.
Simplified code path, condensed duplicate code.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Rename acpi_get_register and acpi_set_register to clarify the
purpose of these functions. New names are acpi_read_bit_register
and acpi_write_bit_register.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Removed locking for reads from the ACPI bit registers in PM1
Status, Enable, Control, and PM2 Control. The lock is not required
when reading the single-bit registers. The acpi_get_register_unlocked
function is no longer needed and has been removed. This will
improve performance for reads on these registers. ACPICA BZ 760.
http://www.acpica.org/bugzilla/show_bug.cgi?id=760
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Split some long lines.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Removed some of the extraneous debug prints using the DB_INFO
level. This should make the DB_INFO more useful.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Print input strings and the result (supported or not supported)
for invocations of the _OSI method.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This function is only needed on 64-bit host operating systems.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove all instances of this obsolete macro, since it is now a
simple reference to ->common.type. There were about 150 invocations
of the macro across 41 files. ACPICA BZ 755.
http://www.acpica.org/bugzilla/show_bug.cgi?id=755
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Added acpi_hw_write_pm1_control. This function writes both of the PM1
control registers (A/B). These registers are different than than
the PM1 A/B status and enable registers in that different values
can be written to the A/B registers. Most notably, the SLP_TYP
bits can be different, as per the values returned from the _Sx
predefined methods.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This type is the same as TYPE_A. Removed this and all related
instances. Renamed SLEEP_TYPE_A to simply SLEEP_TYPE.
ACPICA BZ 754.
http://www.acpica.org/bugzilla/show_bug.cgi?id=754
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Now return AE_BAD_PARAMETER if the input register pointer is
null, and AE_BAD_ADDRESS if the register has an address of zero.
Previously, these cases simply returned AE_OK. For optional
registers such as PM1B status/enable/control, the caller should
check for a valid register address before calling. ACPICA BZ 748.
http://www.acpica.org/bugzilla/show_bug.cgi?id=748
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The PM1B registers are mirrors of the PM1A registers with
different bits actually implemented. From the ACPI specification:
"Although the bits can be split between the two register blocks
(each register block has a unique pointer within the FADT), the bit
positions are maintained. The register block with unimplemented
bits (that is, those implemented in the other register block)
always returns zeros, and writes have no side effects"
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This function was writing an optional PM1B status register
twice. The existing call to the low-level acpi_hw_register_write
automatically handles a possibly split PM1 A/B register.
ACPICA BZ 751.
http://www.acpica.org/bugzilla/show_bug.cgi?id=751
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
On read, shift B register bits above the A bits. On write,
shift B bits down to zero before writing the B register. New:
acpi_hw_read_multiple, acpi_hw_write_multiple. These two functions now
transparently handle the (possible) split registers for PM1 Status,
Enable, and Control.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Enhance the explanations of the various package return types
for clarity.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add new globals for the PM1 status registers (A/B), similar to the
way the PM1 enable registers are handled. Instead of overloading
the FADT Event Register blocks. This makes the code clearer and
less prone to error.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add a call to acpi_os_table_override during the installation of a
dynamic table (loaded via the Load or LoadTable AML operators).
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Removed the Flags parameter from several internal functions since
it was not being used.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Previously, the table override mechanism was implemented for the
DSDT only. Now, any table in the RSDT/XSDT can be replaced by
the host OS. (including the DSDT).
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add check for invalid handle in acpi_ns_dump_one_object.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch implements uevent suppress in kobject and removes it
from struct device, based on the following ideas:
1,Uevent sending should be one attribute of kobject, so suppressing it
in kobject layer is more natural than in device layer. By this way,
we can do it for other objects embedded with kobject.
2,It may save several bytes for each instance of struct device.(On my
omap3(32bit ARM) based box, can save 8bytes per device object)
This patch also introduces dev_set|get_uevent_suppress() helpers to
set and query uevent_suppress attribute in case to help kobject
as private part of struct device in future.
[This version is against the latest driver-core patch set of Greg,please
ignore the last version.]
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Rename pci_osc_control_set() to acpi_pci_osc_control_set() according
to the other API names in drivers/acpi/pci_root.c.
- Move _OSC related definitions to include/linux/acpi.h because _OSC
related API is implemented in drivers/acpi/pci_root.c now.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Tested-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move PCI _OSC management code from drivers/pci/pci-acpi.c to
drivers/acpi/pci_root.c. The benefits are
- We no longer need struct osc_data and its management code (contents
are moved to struct acpi_pci_root). This simplify the code, and we
no longer care about kmalloc() failure.
- We can make pci_acpi_osc_support() be a static function, which is
called only from drivers/acpi/pci_root.c.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Tested-by: Andrew Patterson <andrew.patterson@hp.com>
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
A number of things that shouldn't be exposed outside the ACPI core
were declared in include/acpi/acpi_drivers.h, where anybody can
see them. This patch moves those declarations to a new "internal.h"
inside drivers/acpi.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Use "help" (not "---help---") consistently throughout.
ACPI can't be a module, so if both ACPI & APM are configured,
we use ACPI.
Update pointers to ACPI CA and Linux ACPI projects.
Replace "Compaq" with "Hewlett-Packard" in the spec developer list.
Fix typo in /sys/module path.
The user-space daemon is "acpid", not "acpi".
Add standard "To compile this driver as a module ..." help text.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Use the generic pci_swizzle_interrupt_pin() instead of ACPI-specific code.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We don't need a struct containing a count and a list_head; a simple
list_head is sufficient. The list iterators handle empty lists
fine.
Furthermore, we don't need to check for null list entries because we
only add non-null entries.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Better to oops and learn about a bug than to silently cover it up.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch makes whitespace and indentation more consistent.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We found Cx states time abnormal in our some of machines which have 16
LCPUs, the C0 take too many time while system is really idle when kernel
enabled tickless and highres. powertop output is below:
PowerTOP version 1.9 (C) 2007 Intel Corporation
Cn Avg residency P-states (frequencies)
C0 (cpu running) (40.5%) 2.53 Ghz 0.0%
C1 0.0ms ( 0.0%) 2.53 Ghz 0.0%
C2 128.8ms (59.5%) 2.40 Ghz 0.0%
1.60 Ghz 100.0%
Wakeups-from-idle per second : 4.7 interval: 20.0s
no ACPI power usage estimate available
Top causes for wakeups:
41.4% ( 24.9) <interrupt> : extra timer interrupt
20.2% ( 12.2) <kernel core> : usb_hcd_poll_rh_status
(rh_timer_func)
After tacking detailed for this issue, Yakui and I find it is due to 24
bit PM timer overflows when some of cpu sleep more than 4 seconds. With
tickless kernel, the CPU want to sleep as much as possible when system
idle. But the Cx sleep time are recorded by pmtimer which length is
determined by BIOS. The current Cx time was gotten in the following
function from driver/acpi/processor_idle.c:
static inline u32 ticks_elapsed(u32 t1, u32 t2)
{
if (t2 >= t1)
return (t2 - t1);
else if (!(acpi_gbl_FADT.flags & ACPI_FADT_32BIT_TIMER))
return (((0x00FFFFFF - t1) + t2) & 0x00FFFFFF);
else
return ((0xFFFFFFFF - t1) + t2);
}
If pmtimer is 24 bits and it take 5 seconds from t1 to t2, in above
function, just about 1 seconds ticks was recorded. So the Cx time will be
reduced about 4 seconds. and this is why we see above powertop output.
To resolve this problem, Yakui and I use ktime_get() to record the Cx
states time instead of PM timer as the following patch. the patch was
tested with i386/x86_64 modes on several platforms.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Tested-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Yakui.zhao <yakui.zhao@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
It is hardly (if ever) possible but in case of broken _PXM entry we could
reach out of pxm_to_node_map array bounds in acpi_map_pxm_to_node() call.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
There was a misplaced status test (two consequent tests without a
statement in between) in acpi_bus_init for ages. Remove it, since the
function which should be checked (acpi_os_initialize1) has BUG_ONs on
failure paths.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This reverts commit 5ec5d38a1c.
because it caused spurious dmesg warmings.
We'll implement the check for off-limit ports
in a more clever way in the future.
http://bugzilla.kernel.org/show_bug.cgi?id=12758
Signed-off-by: Len Brown <len.brown@intel.com>
Switch the Asus Pundit P1-AH2 (M2N8L motherboard) to the old ACPI 1.0
sleep ordering by default. Without this it will not suspend/resume
correctly.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Tested-by: Dustin Kirkland <kirkland@canonical.com>
Signed-off-by: Len Brown <len.brown@intel.com>
SSDT tables may be loaded at runtime.
create sysfs I/F for these dynamic tables in
/sys/firmware/acpi/tables/dynamic/.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
early_acpi_os_unmap_memory() is an __init function, and
acpi_os_unmap_memory() is allowed to access an __init function
until acpi_gbl_permanent_mmap is set up.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove CONFIG_ACPI_SYSTEM. It was always set the same as CONFIG_ACPI,
and it had no menu label, so there was no way to set it to anything
other than "y".
Some things under CONFIG_ACPI_SYSTEM (acpi_irq_handled, acpi_os_gpe_count(),
event_is_open, register_acpi_notifier(), etc.) are used unconditionally
by the CA, the OSPM, and drivers, so we depend on them always being
present.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
On hardware like the T61 it can take a couple of seconds for the battery
to start charging after the power is connected, and we incorrectly tell
userspace that we are fully charged, and then go back to charging.
Only mark a battery as fully charged when the preset charge matches either
the last full charge, or the design charge.
http://bugzilla.kernel.org/show_bug.cgi?id=12632
Signed-off-by: Richard Hughes <hughsient@gmail.com>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
The ACPI code currently carries its own thermal trip handling, meaning that
any other thermal implementation will need to reimplement it. Move the code
to the generic thermal layer.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The thermal API currently uses strings to pass values to userspace. This
makes it difficult to use from within the kernel. Change the interface
to use integers and fix up the consumers.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Impact: cleanup
There are two allocated per-cpu accessor macros with almost identical
spelling. The original and far more popular is per_cpu_ptr (44
files), so change over the other 4 files.
tj: kill percpu_ptr() and update UP too
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: mingo@redhat.com
Cc: lenb@kernel.org
Cc: cpufreq@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
to prevent wrongly overwriting fixmap that still want to use.
ACPI used to rely on low mappings being all linearly mapped and
grew a habit: it never really unmapped certain kinds of tables
after use.
This can cause problems - for example the hypothetical case
when some spurious access still references it.
v2: remove prev_map and prev_size in __apci_map_table
v3: let acpi_os_unmap_memory() call early_iounmap too, so remove extral calling to
early_acpi_os_unmap_memory
v4: fix typo in one acpi_get_table_with_size calling
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On x86, __acpi_map_table uses early_ioremap() to create the mapping,
replacing the previous mapping with a new one. Once enough of the
kernel is up an running it switches to using normal ioremap(). At
that point, we need to clean up the final mapping to avoid a warning
from the early_ioremap subsystem.
This can be removed after all the instances in the ACPI code are fixed
that rely on early-ioremap's implicit overmapping of previously
mapped tables.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
During early boot, ACPI RSDT/XSDT table entries are gathered into the
'initial_tables[]' array. This array is currently statically defined (see
./drivers/acpi/tables.c). When there are more table entries than can be
held in the 'initial_tables[]' array, the message "Truncating N table
entries!" is output. As currently implemented, this message will always
erroneously calculate N as 0.
This patch fixes the calculation that determines how many table entries
will be missing (truncated).
This modification may be used under either the GPL or the BSD-style
license used for Intel ACPI CA code.
Signed-off-by: Myron Stowe <myron.stowe@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
According to kerneljanitors todo list all printk calls (beginning
a new line) should have an according KERN_* constant.
Those are the missing peaces here for the acpi subsystem.
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Some devices trigger a DEVICE_CHECK on every evalutation of _STA. This
can also be seen in commit 8b59560a3b
(ACPI: dock: avoid check _STA method). If an undock is processed, the
dock driver sends a uevent and userspace might read the show_docked
property in sysfs. This causes an evaluation of _STA of the particular
device which causes the dock driver to immediately dock again.
In any case, evaluation of _STA (show_docked) does not necessarily mean
that we are docked, so check with the internal device structure.
http://bugzilla.kernel.org/show_bug.cgi?id=12360
Signed-off-by: Holger Macht <hmacht@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
When ACPI is disabled in the BIOS of this VIA C3 box,
it invalidates the RSDP, which Linux notices:
ACPI Error (tbxfroot-0218): A valid RSDP was not found [20080926]
Bug Linux neglected to disable ACPI at that stage,
and later scribbled on smp_found_config:
ACPI: No APIC-table, disabling MPS
But this box doesn't run well in legacy PIC mode,
it needed IOAPIC mode to perform correctly:
http://lkml.org/lkml/2009/2/5/39
So exit ACPI mode cleanly when we first detect
that it is hopeless.
Signed-off-by: Len Brown <len.brown@intel.com>
CPU_IDLE=y has been default for ACPI=y since Nov-2007,
and has shipped in many distributions since then.
Here we delete the CPU_IDLE=n ACPI idle code, since
nobody should be using it, and we don't want to
maintain two versions.
Signed-off-by: Len Brown <len.brown@intel.com>
Currently, netlink_broadcast() reports errors to the caller if no
messages at all were delivered:
1) If, at least, one message has been delivered correctly, returns 0.
2) Otherwise, if no messages at all were delivered due to skb_clone()
failure, return -ENOBUFS.
3) Otherwise, if there are no listeners, return -ESRCH.
With this patch, the caller knows if the delivery of any of the
messages to the listeners have failed:
1) If it fails to deliver any message (for whatever reason), return
-ENOBUFS.
2) Otherwise, if all messages were delivered OK, returns 0.
3) Otherwise, if no listeners, return -ESRCH.
In the current ctnetlink code and in Netfilter in general, we can add
reliable logging and connection tracking event delivery by dropping the
packets whose events were not successfully delivered over Netlink. Of
course, this option would be settable via /proc as this approach reduces
performance (in terms of filtered connections per seconds by a stateful
firewall) but providing reliable logging and event delivery (for
conntrackd) in return.
This patch also changes some clients of netlink_broadcast() that
may report ENOBUFS errors via printk. This error handling is not
of any help. Instead, the userspace daemons that are listening to
those netlink messages should resync themselves with the kernel-side
if they hit ENOBUFS.
BTW, netlink_broadcast() clients include those that call
cn_netlink_send(), nlmsg_multicast() and genlmsg_multicast() since they
internally call netlink_broadcast() and return its error value.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
They were long enough set deprecated...
Update Documentation/cpu-freq/users-guide.txt:
The deprecated files listed there seen not to exist for some time anymore
already.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPICA exports acpi_os_validate_address() so the OS
can prevent BIOS AML from accessing specified addresses.
Start using this interface to prevent AML from accessing
some well known IO addresses that the OS "owns".
Signed-off-by: Len Brown <len.brown@intel.com>
on boot, print out the OSI strings the BIOS uses to query the OS.
To see this output...
build with CONFIG_ACPI_DEBUG
boot with
"acpi.debug_level=4" (ACPI_LV_INFO) (enabled by default)
and
"acpi.debug_level=1" (ACPI_UTILITIES) (default is 0)
example output:
ACPI: BIOS _OSI(Windows 2001) supported
ACPI: BIOS _OSI(Windows 2001 SP1) supported
ACPI: BIOS _OSI(Windows 2001 SP2) supported
ACPI: BIOS _OSI(Windows 2006) supported
ACPI: BIOS _OSI(Linux) not-supported
ACPI: BIOS _OSI(FreeBSD) not-supported
Signed-off-by: Len Brown <len.brown@intel.com>
According to the Spec the first two elements in the _BCL package won't be
regarded as the available brightness level. The first is the brightness when
full power is connected to the box(It means that the AC adapter is plugged).
The second is the brightness level when the box is on battery.
If the first two elements are still used while finding the next brightness
level, it will fall back to the lowest level when keeping on pressing
hotkey. (On some boxes the brightness will be changed twice when hotkey is
pressed once. One is in the ACPI video driver. The other is changed by sys I/F.
In the ACPI video driver the first two elements will be used while changing
the brightness. But the first two elements is skipped while using sys I/F.
In such case there exists the inconsistency).
So he first two elements had better be skipped while showing the available
brightness or finding the next brightness level.
http://bugzilla.kernel.org/show_bug.cgi?id=12450
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
It is true that BM_RLD needs to be set to enable
bus master activity to wake an older chipset (eg PIIX4) from C3.
This is contrary to the erroneous wording the ACPI 2.0, 3.0
specifications that suggests that BM_RLD is an indicator
rather than a control bit.
ACPI 1.0's correct wording should be restored in ACPI 4.0:
http://www.acpica.org/bugzilla/show_bug.cgi?id=689
But the kernel should not have to clear BM_RLD
when entering a non C3-type state just to set
it again when entering a C3-type C-state.
We should be able to set BM_RLD at boot time
and leave it alone -- removing the overhead of
accessing this IO register from the idle entry path.
Signed-off-by: Len Brown <len.brown@intel.com>
PM1a_STS and PM1b_STS are twins that get OR'd together
on reads, and all writes are repeated to both.
The fields in PM1x_STS are single bits only,
there are no multi-bit fields.
So it is not necessary to lock PM1x_STS reads against
writes because it is impossible to read an intermediate
value of a single bit. It will either be 0 or 1,
even if a write is in progress during the read.
Reads are asynchronous to writes no matter if a lock
is used or not.
Signed-off-by: Len Brown <len.brown@intel.com>
This patch fixes the crash I experienced in 2.6.29-rc2.
Tested on ASUS M50vm.
Signed-off-by: Tero Roponen <tero.roponen@gmail.com>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix two compilation warnings in drivers/acpi/sleep.c, one triggered
by unsetting CONFIG_SUSPEND and the other triggered by unsetting
CONFIG_HIBERNATION, by moving some code under the appropriate
#ifdefs .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Conflicts:
drivers/acpi/pci_irq.c
Note that this merge disables
e1d3a90846
pci, acpi: reroute PCI interrupt to legacy boot interrupt equivalent
Signed-off-by: Len Brown <len.brown@intel.com>
when CONFIG_RTC_DRV_CMOS=m
and thus !defined(HAVE_ACPI_LEGACY_ALARM)
drivers/acpi/proc.c:85: warning: ‘cmos_bcd_read’ declared ‘static’ but
never defined
Signed-off-by: Len Brown <len.brown@intel.com>
On some boxes there exist both RSDT and XSDT table. But unfortunately
sometimes there exists the following error when XSDT table is used:
a. 32/64X address mismatch
b. The 32/64X FACS address mismatch
In such case the boot option of "acpi=rsdt" is provided so that
RSDT is tried instead of XSDT table when the system can't work well.
http://bugzilla.kernel.org/show_bug.cgi?id=8246
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
cc:Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI_USE_LOCAL_CACHE will never be defined by the Linux kernel,
and thus utcache.c will always be dead code.
Signed-off-by: Len Brown <len.brown@intel.com>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (98 commits)
PCI PM: Put PM callbacks in the order of execution
PCI PM: Run default PM callbacks for all devices using new framework
PCI PM: Register power state of devices during initialization
PCI PM: Call pci_fixup_device from legacy routines
PCI PM: Rearrange code in pci-driver.c
PCI PM: Avoid touching devices behind bridges in unknown state
PCI PM: Move pci_has_legacy_pm_support
PCI PM: Power-manage devices without drivers during suspend-resume
PCI PM: Add suspend counterpart of pci_reenable_device
PCI PM: Fix poweroff and restore callbacks
PCI: Use msleep instead of cpu_relax during ASPM link retraining
PCI: PCIe portdrv: Add kerneldoc comments to remining core funtions
PCI: PCIe portdrv: Rearrange code so that related things are together
PCI: PCIe portdrv: Fix suspend and resume of PCI Express port services
PCI: PCIe portdrv: Add kerneldoc comments to some core functions
x86/PCI: Do not use interrupt links for devices using MSI-X
net: sfc: Use pci_clear_master() to disable bus mastering
PCI: Add pci_clear_master() as opposite of pci_set_master()
PCI hotplug: remove redundant test in cpq hotplug
PCI: pciehp: cleanup register and field definitions
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
The _OSC capability OSC_MSI_SUPPORT is set when the root bridge is added
with pci_acpi_osc_support(), so we no longer need to do it in the PCI
MSI driver. Also adds the function pci_msi_enabled, which returns true
if pci=nomsi is not on the kernel command-line.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The _OSC capabilities OSC_ACTIVE_STATE_PWR_SUPPORT and
OSC_CLOCK_PWR_CAPABILITY_SUPPORT are set when the root bridge is added
with pci_acpi_osc_support(), so we no longer need to do it in the ASPM
driver. Also add the function pcie_aspm_enabled, which returns true if
pcie_aspm=off is not on the kernel command-line.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The _OSC capability OSC_EXT_PCI_CONFIG_SUPPORT is set when the root
bridge is added with pci_acpi_osc_support() if we can access PCI
extended config space.
This adds the function pci_ext_cfg_avail which returns true if we can
access PCI extended config space (offset greater than 0xff). It
currently only returns false if arch=x86 and raw_pci_ext_ops is not set
(which might happen if pci=nommcfg is set on the kernel command-line).
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add pci_acpi_osc_support() and call it when a PCI bridge is added. This
allows us to avoid having every individual PCI root bridge driver call
_OSC support for every root bridge in their probe functions, a
significant savings in boot time.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
While looking at reducing the amount of architecture namespace pollution
in the generic kernel, I found that asm/irq.h is included in the vast
majority of compilations on ARM (around 650 files.)
Since asm/irq.h includes a sub-architecture include file on ARM, this
causes a negative impact on the ccache's ability to re-use the build
results from other sub-architectures, so we have a desire to reduce the
dependencies on asm/irq.h.
It turns out that a major cause of this is the needless include of
linux/hardirq.h into asm-generic/local.h. The patch below removes this
include, resulting in some 250 to 300 files (around half) of the kernel
then omitting asm/irq.h.
My test builds still succeed, provided two ARM files are fixed
(arch/arm/kernel/traps.c and arch/arm/mm/fault.c) - so there may be
negative impacts for this on other architectures.
Note that x86 does not include asm/irq.h nor linux/hardirq.h in its
asm/local.h, so this patch can be viewed as bringing the generic version
into line with the x86 version.
[kosaki.motohiro@jp.fujitsu.com: add #include <linux/irqflags.h> to acpi/processor_idle.c]
[adobriyan@gmail.com: fix sparc64]
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix misspelling of "firmware" in acpi_memhotplug.c
It's spelled "firmware".
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It is always "an" if there is a vowel _spoken_ (not written).
So it is:
"an hour" (spoken vowel)
but
"a uniform" (spoken 'j')
Signed-off-by: Frederik Schwarzer <schwarzerf@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Impact: Reduce memory usage, use new API.
This is part of an effort to reduce structure sizes for machines
configured with large NR_CPUS. cpumask_t gets replaced by
cpumask_var_t, which is either struct cpumask[1] (small NR_CPUS) or
struct cpumask * (large NR_CPUS).
(Changes to powernow-k* by <travis>.)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Update all messages so they look consistent.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This returns the FADT support to the original behavior, which is
to use default register widths. However, now check each register
definition and report a warning if it differs from the default.
This is a first step to moving away from the default widths,
rather than outright believing the widths in all FADTs for all
machines, considered rather dangerous until more data is obtained.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
1) Update the register lengths for the PM1 event blocks. The
length must be divided by two in order to use these to access
the status registers.
2) Add run-time option to use default register lengths to override a
faulty FADT.
3) Add warning message if any of the X64 address structures contain a length
that does not match the legacy length earlier in the FADT.
4) Move all FADT warning messages into the ValidateFadt function.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi.h now includes only the "public" acpica headers. All other
acpica headers are "private" and should not be included by acpica
users. One new file, accommon.h is used to include the commonly
used private headers for acpica code generation. Future plans
are to move all private headers to a new subdirectory.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
External driver files should not include any private acpica headers.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Uses the FADT-defined reset register and reset value. Checks the
FADT flags for the reset register supported bit. Supports reset
register in memory or I/O space, but not in PCI config space
since the host has the information to do it.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Move public interfaces from hwregs.c to new file, hwxface.c -
similar to the structure of the other ACPICA components.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Changed the acpi_hw_low_level_read and acpi_hw_low_level_write functions to
the public acpi_read and acpi_write to allow direct access to
ACPI registers. Removed the "width" parameter since the width
can be obtained from the input GAS structure. Updated the FADT
initialization to setup the GAS structures with the proper
widths. Some widths are still hardcoded because many FADTs have
incorrect register lengths.
Signed-off-by: Bob Moore <robert.moore@intel.com
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_ut_get_node_name is an internal acpica function.
use acpi_get_name to get node ascii name
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Avoid using internal functions: acpi_hw_disable_all_gpes and acpi_hw_enable_all_runtime_gpes
Use new public GPE group enable/disable interfaces: acpi_disable_all_gpes and acpi_enable_all_runtime_gpes
Also avoid using internal symbol ACPI_TABLE_INDEX_FACS, call acpi_get_table.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Added acpi_disable_all_gpes and acpi_enable_all_runtime_gpes for
public use.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This function maps an input GPE index to a GPE block device. Also
Added acpi_current_gpe_count to track the current number of GPEs
that are being managed by the ACPICA core (both FADT-based GPEs
and the GPEs contained in GPE block devices.)
Modify drivers/acpi/system.c to use these 2 new interfaces
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI_FUNCTION_TRACE is an internal acpica function.
remove ACPI_FUNCTION_TRACE
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI_FUNCTION_TRACE and return_VALUE are internal acpica functions.
remove ACPI_FUNCTION_TRACE
replace return_VALUE with return
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_namespace_node is internal struct, it should not be used outside of ACPICA
call acpi_get_name to get node ascii name
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
return_ACPI_STATUS is an internal acpica function, replace it with return.
acpi_gbl_permanent_mmap moved from acglobal.h to acpixf.h for external use
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
always update props.brightness no matter the backlight is changed
via procfs, hotkeys or sysfs.
Sighed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Len Brown <len.brown@intel.com>
use ACPI_ALLOCATE_BUFFER to remove the allocations
within acpi_pci_bind(), acpi_pci_unbind() and acpi_pci_bind_root().
While there, delete some unnecessary param inits from those routines.
Delete concept of ACPI_PATHNAME_MAX, since this was the last use.
Signed-off-by: Len Brown <len.brown@intel.com>
This patch makes function declarations consistent throughout
the file and removes some unnecessary initializations.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_pci_allocate_irq() and acpi_pci_free_irq() are trivial and
only used once, so just open-code them.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We don't need a struct containing a count and a list_head; a simple
list_head is sufficient. The list iterators handle empty lists
fine.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This folds acpi_pci_irq_derive() into acpi_pci_irq_lookup() so it
can be easily used by both acpi_pci_irq_enable() and acpi_pci_irq_disable().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
No functional change; this just uses the typical pattern of
PCI INTx swizzling done on other architectures.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This doesn't change anything functionally; it just changes tests
so we test for success instead of failure. This makes the code
read more easily and allows us to remove the "!entry" in the while
loop condition.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We currently pass a callback function (either acpi_pci_allocate_irq() or
acpi_pci_free_irq()) to acpi_pci_irq_lookup() and acpi_pci_irq_derive().
I think it's simpler to remove the callback and just have the enable/
disable functions make the calls directly.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Print one message (either "found" or "not found") for every _PRT
search. And add pin information to the INTx swizzling debug.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
There's no reason to pass around segment, bus, and device independently
when we can just pass the pci_dev pointer, which carries all those
already.
The pci_dev contains an interrupt pin, too, but we still have to pass both
the pci_dev and the pin because when we use a bridge to derive an IRQ, we
need the pin from the downstream device, not the bridge.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Use the PCI INTx pin encoding (1=INTA, 2=INTB, etc) for _PRT quirks.
Then we can simply compare "entry->pin == quirk->pin".
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch changes pci_irq.c to always use PCI INTx pin encodings
instead of a mix of PCI and _PRT encodings.
The PCI INTx pin numbers from the PCI_INTERRUPT_PIN config register
are 0=device doesn't use interrupts, 1=INTA, ..., 4=INTD. But the
_PRT table uses 0=INTA, ..., 3=INTD.
This patch converts the _PRT encoding to the PCI encoding immediately
when we add a _PRT entry to the global list. All the rest of the
code can then use the PCI encoding consistently.
The point of this is to make the interrupt swizzling look the same
as on other architectures, so someday we can unify them.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This adds a helper function to convert INTx pin numbers from the _PRT
(0, 1, 2, 3) to the pin name ('A', 'B', 'C', 'D').
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The struct acpi_prt_entry is used only in pci_irq.c, so there's no
need for the declaration to be public. This patch moves it into
pci_irq.c.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The interrupt numbers from _PRT entries are GSIs, not Linux IRQs.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
_PRT entries don't contain any useful PCI function information (the
function part of the PCI address is supposed to be 0xffff), and we
don't ever look at it, so this patch just removes the reference to
it.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Previously, acpi_pci_irq_add_prt() did all its own buffer management.
But now that we have ACPI_ALLOCATE_BUFFER, we no longer need to do
that management. And we don't have to call acpi_get_irq_routing_table()
twice (once to learn the size of the buffer needed, and again to
actually get the table).
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Better to oops and learn about a bug than to silently cover it up.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Use the conventional format for PCI addresses (%04x:%02x:%02x.%d).
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
According to the ACPI specification the SCI_EN flag is controlled by
the hardware, which sets this flag to inform the kernel that ACPI is
enabled. For this reason, we shouldn't try to modify SCI_EN
directly. Also, we don't need to do it in irqrouter_resume(), since
lower-level resume code takes care of enabling ACPI in case it hasn't
been enabled by the BIOS before passing control to the kernel (which
by the way is against the ACPI specification).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
For Windows compatibility, return an implicit integer of value
zero for methods that have no executable code. A default implicit
value of zero is provided for methods. Lin Ming.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Merge the code that validates control method argument counts into
the predefined validation module. Eliminates possible multiple
warnings for incorrect counts.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
For predefined methods (such as _BIF), add automatic conversion for
objects that are required to be a String, but a Buffer was found
instead. This can happen when reading string battery data from
an operation region, because it used to be difficult to convert
the data from buffer to string from within the ASL. Linux BZ 11822.
http://bugzilla.kernel.org/show_bug.cgi?id=11822
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
In a fully qualified namepath, allow multiple backslash prefixes.
This can happen because of the use of a double-backslash in strings
(since backslash is the escape character) causing confusion.
ACPICA BZ 739 Lin Ming.
http://www.acpica.org/bugzilla/show_bug.cgi?id=739
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes a problem where the use of an alias within a namepath
would result in a not found error or cause the compiler to fault.
Also now allows forward references from the Alias operator itself.
ACPICA BZ 738.
http://www.acpica.org/bugzilla/show_bug.cgi?id=738
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This define is no longer used.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The current implemenation of _OSI within ACPICA only allows other
control methods to execute _OSI. This change allows the host
OS to execute _OSI via the AcpiEvaluateObject interface. _OSI
is a special method -- it does not exist in the AML code, it is
implemented within ACPICA.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Reformat comments to use fewer lines.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Use a global pointer instead of using AcpiGetTableByIndex for
each FACS access. This simplifies the code for the Global Lock
and the Firmware Waking Vector(s).
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Checks if there are two valid but different addresses for the
FACS and DSDT within the FADT (mismatch between the 32-bit and
64-bit fields.)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This fixes the name of this address space, changing it from the
incorrect CMOS to the correct SystemCMOS.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Split the "data register I/O" with more informative read and
write messages.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add a loop counter to force exit from AML While loops if the
count becomes too large. This can occur in poorly written AML
when the hardware does not respond within a while loop and the
loop does not implement a timeout. The maximum loop count is
configurable. A new exception code is returned when a loop is
broken, AE_AML_INFINITE_LOOP. Bob Moore, Alexey Starikovskiy.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Previously, a control state object was allocated and freed for
each execution of the loop. The optimization is to simply reuse
the control state for each iteration. This speeds up the raw loop
execution time by about 5%.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes a possible memory leak if an allocation failure happens in
the parse loop. Must terminate an executing control method.
Lin Ming, Bob Moore. ACPICA BZ 489.
http://www.acpica.org/bugzilla/show_bug.cgi?id=489
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Split AcpiSetFirmwareWakingVector into two: one for the 32-bit
vector, another for the 64-bit vector. This is required because the
host OS must setup the wake much differently for each vector (real
vs. protected mode, etc.) and the interface should not be deciding
which vector to use. Also eliminate the GetFirmwareWakingVector
interface, as it served no purpose (only the firmware reads the
vector, OS only writes the vector.) ACPICA BZ 731.
http://www.acpica.org/bugzilla/show_bug.cgi?id=731
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
New compiler is pickier than older versions.
Joerg Sonnenberger. From ACPICA BZ 732.
http://www.acpica.org/bugzilla/show_bug.cgi?id=732
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
update of battery info fields is required.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Andy Neitzke <neitzke@ias.edu>
Signed-off-by: Alexey Starikovskiy <astarikovskiy <at> suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
These are platform specific drivers that happen to use ACPI,
while drivers/acpi/ is for code that implements ACPI itself.
Signed-off-by: Len Brown <len.brown@intel.com>
On some machines it may be necessary to disable the saving/restoring
of the ACPI NVS memory region during hibernation/resume. For this
purpose, introduce new ACPI kernel command line option
acpi_sleep=s4_nonvs.
Based on a patch by Zhang Rui.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@tuxonice.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
According to the ACPI Specification 3.0b, Section 15.3.2,
"OSPM will call the _PTS control method some time before entering a
sleeping state, to allow the platform's AML code to update this
memory image before entering the sleeping state. After the system
awakes from an S4 state, OSPM will restore this memory area and call
the _WAK control method to enable the BIOS to reclaim its memory
image." For this reason, implement a mechanism allowing us to save
the NVS memory during hibernation and to restore it during the
subsequent resume.
Based on a patch by Zhang Rui.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@tuxonice.net>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_early_init() was changed to over-write the cmdline param,
making it really inconvenient to set debug flags at boot-time.
Also,
This sets the default level to "info", which is what all the ACPI
drivers use. So to enable messages from drivers, you only have to
supply the "layer" (a.k.a. "component"). For non-"info" ACPI core
and ACPI interpreter messages, you have to supply both level and
layer masks, as before.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Impact: reward non-stop TSCs with good TSC-based clocksources, etc.
Add support for CPUID_0x80000007_Bit8 on Intel CPUs as well. This bit means
that the TSC is invariant with C/P/T states and always runs at constant
frequency.
With Intel CPUs, we have 3 classes
* CPUs where TSC runs at constant rate and does not stop n C-states
* CPUs where TSC runs at constant rate, but will stop in deep C-states
* CPUs where TSC rate will vary based on P/T-states and TSC will stop in deep
C-states.
To cover these 3, one feature bit (CONSTANT_TSC) is not enough. So, add a
second bit (NONSTOP_TSC). CONSTANT_TSC indicates that the TSC runs at
constant frequency irrespective of P/T-states, and NONSTOP_TSC indicates
that TSC does not stop in deep C-states.
CPUID_0x8000000_Bit8 indicates both these feature bit can be set.
We still have CONSTANT_TSC _set_ and NONSTOP_TSC _not_set_ on some older Intel
CPUs, based on model checks. We can use TSC on such CPUs for time, as long as
those CPUs do not support/enter deep C-states.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Section B.6.2 of ACPI 3.0b specification that defines _BCL method
doesn't require the brightness levels returned to be sorted.
At least ThinkPad SL300 (and probably all IdeaPads) returns the
array reversed (i.e. bightest levels have lowest indexes), which
causes the brightness management behave in completely reversed
manner on these machines (brightness increases when the laptop is
idle, while the display dims when used).
Sorting the array by brightness level values after reading the list
fixes the issue.
http://bugzilla.kernel.org/show_bug.cgi?id=12037
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix month wrap issue with readback from /proc/acpi/alarm
This bug has been around *forever*.
$ echo '2008-12-01 10:36:20' > /proc/acpi/alarm
$ cat /proc/acpi/alarm
2008-11-01 10:36:20
Note how the readback above shows the month incorrectly
when the alarm is set in the *next* calendar month.
But with this patch applied, it shows the correct month (12).
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This reverts commit 558073dd56, along with
the failed try to fix the regression it caused ("ACPI: Fix ACPI battery
regression introduced by commit 558073"), which just made things worse.
Commit aaad077638 (that failed "Fix ACPI
battery regression") got the voltage conversion confused, and fixed the
problem with Rafael's battery monitor apparently just by mistake.
So revert them both, getting us back to the 2.6.27 state in this, and
let's revisit it when people understand what's going on.
Noted-by: Paul Martin <pm@debian.org>
Requested-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <len.brown@intel.com>
Cc: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 558073dd56 ("ACPI: battery: Convert
discharge energy rate to current properly") caused the battery subsystem
to report wrong values of the remaining time on battery power and the
time until fully charged on Toshiba Portege R500 (and presumably on
other boxes too).
Fix the issue by correcting the conversion from mW to mA.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the warning introduced in commit c5279dee26,
and give the dummy variable a more verbose name.
drivers/acpi/ec.c: In function 'acpi_ec_ecdt_probe':
drivers/acpi/ec.c:1015: warning: ISO C90 forbids mixed declarations and code
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
the toshiba ACPI driver will, in a failure case, free the rfkill state
before stopping the polling timer that would use this state. More interesting,
in the same failure case handling, it calls the exit function, which also
frees the rfkill state, but after stopping the polling.
If the race happens, a NULL pointer is passed to rfkill_force_state()
which then causes a nice dereference.
Fix the race by just not doing the too-early freeing of the rfkill state.
This appears to be the cause of a hot issue on kerneloops.org; while I
have no solid evidence of that this patch will fix the issue, the race
appears rather real.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Linux will continue to ignore OSI(Linux),
except for a white-list containing a few systems.
So delete the black-list,
and stop soliciting user-feedback on the console.
Signed-off-by: Len Brown <len.brown@intel.com>
Some Apple boxes evidently require us to set SCI_EN on resume
directly, because if we don't do that, they hung somewhere in the
resume code path. Moreover, on these boxes it is not sufficient to
use acpi_enable() to turn ACPI on during resume. All of this is
against the ACPI specification which states that (1) the BIOS is
supposed to return from the S3 sleep state with ACPI enabled
(SCI_EN set) and (2) the SCI_EN bit is owned by the hardware and we
are not supposed to change it.
For this reason, blacklist the affected systems so that the SCI_EN
bit is set during resume on them.
[NOTE: Unconditional setting SCI_EN for all system on resume doesn't
work, because it makes some other systems crash (that's to be
expected). Also, it is not entirely clear right now if all of the
Apple boxes require this workaround.]
This patch fixes the recent regression tracked as
http://bugzilla.kernel.org/show_bug.cgi?id=12038
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Tino Keitel <tino.keitel@gmx.de>
Tested-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Now I know why I had strange "scheduling in atomic" problems:
acpi_evaluate_integer() does malloc(..., irqs_disabled() ? GFP_ATOMIC
: GFP_KERNEL)... which is (of course) broken.
There's no way to reliably tell if we need GFP_ATOMIC or not from
code, this one for example fails to detect spinlocks held.
Fortunately, allocation seems small enough to be done on stack.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Acked-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI battery interface reports its state either in mW or in mA, and
discharge rate in your case is reported in mW. power_supply interface
does not have such a parameter, so current_now parameter is used
for all cases. But in case of mW, reported discharge should
be converted into mA.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Ferenc Wagner <wferi@niif.hu>
Signed-off-by: Len Brown <len.brown@intel.com>
One more ASUS comes with empty ECDT, add a guard for it...
http://bugzilla.kernel.org/show_bug.cgi?id=11880
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Commit 0794469da3: ("ACPI: struct device -
replace bus_id with dev_name(), dev_set_name()") introduced a bug by
testing 'dev_name(ldev)' instead of 'ldev->bus' for NULL when printing
out the bus information.
So if ldev->bus was NULL, we'd oops.
Reported-and-tested-by: Bruno Prmont <bonbons@linux-vserver.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Len Brown <len.brown@intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This removes the acpi_irq_balance_set() interface from the PCI
interrupt link driver.
x86 used acpi_irq_balance_set() to tell the PCI interrupt link
driver to configure links to minimize IRQ sharing. But the link
driver can easily figure out whether to turn on IRQ balancing
based on the IRQ model (PIC/IOAPIC/etc), so we can get rid of
that external interface.
It's better for the driver to figure this out at init-time. If
we set it externally via the x86 code, the interface reduces
modularity, and we depend on the fact that acpi_process_madt()
happens before we process the kernel command line.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Disabling gpe might interfere with gpe detection/handling,
thus producing "interrupt not handled" errors.
Ironically, disabling of GPE from interrupt context is already
under spinlock, so only userspace needs to start using it.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Restart current transaction if we recieved unexpected GPEs instead
of needed ones.
http://bugzilla.kernel.org/show_bug.cgi?id=11896
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
There is a possibility that EC might break if next command is
issued within 1 us after write or burst-disable command.
Suggestd-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Make sure we can tell if the GPE storm workaround gets activated,
and avoid flooding the logs afterwards.
http://bugzilla.kernel.org/show_bug.cgi?id=11841
"plenty of line "ACPI: EC: non-query interrupt received,
switching to interrupt mode" in dmesg"
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
If an ACPI graphics device supports backlight brightness functions (cmp. with
latest ACPI spec Appendix B), let the ACPI video driver control backlight and
switch backlight control off in vendor specific ACPI drivers (asus_acpi,
thinkpad_acpi, eeepc, fujitsu_laptop, msi_laptop, sony_laptop, acer-wmi).
Currently it is possible to load above drivers and let both poke on the
brightness HW registers, the video and vendor specific ACPI drivers -> bad.
This patch provides the basic support to check for BIOS capabilities before
driver loading time. Driver specific modifications are in separate follow up
patches.
"acpi_backlight=vendor"
Prever vendor driver over ACPI driver for backlight.
"acpi_backlight=video" (default)
Prever ACPI driver over vendor driver for backlight.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This is a reimplemention of commit
0119509c4f
from Matthew Garrett <mjg59@srcf.ucam.org>
This patch got removed because of a regression: ThinkPads with a
Intel graphics card and an Integrated Graphics Device BIOS implementation
stopped working.
In fact, they only worked because the ACPI device of the discrete, the
wrong one, got used (via int10). So ACPI functions were poking on the wrong
hardware used which is a sever bug.
The next patch provides support for above ThinkPads to be able to
switch brightness via the legacy thinkpad_acpi driver and automatically
detect when to use it.
Original commit message from Matthew Garrett:
Vendors often ship machines with a choice of integrated or discrete
graphics, and use the same DSDT for both. As a result, the ACPI video
module will locate devices that may not exist on this specific platform.
Attempt to determine whether the device exists or not, and abort the
device creation if it doesn't.
http://bugzilla.kernel.org/show_bug.cgi?id=9614
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Len's tree branch release-2.6.27, found an unwanted return statement at
evgpe.c.
(git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
release-2.6.27)
Signed-of-by Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Reformat acpi.debug_layer and acpi.debug_level documentation so it's
more readable, add some clues about how to figure out the mask bits that
enable a specific ACPI_DEBUG_PRINT statement, and include some useful
examples.
Move the list of masks to Documentation/acpi/debug.txt (these are
copies of the authoritative values in acoutput.h and acpi_drivers.h).
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When CONFIG_ACPI_DEBUG=y, the default acpi_dbg_layer and acpi_dbg_level
values built into the ACPI CA have some debug output enabled. We'd
rather be quiet unless the user actually specified the acpi.debug_level
argument.
This enables distros to ship with CONFIG_ACPI_DEBUG=y without
inundating users with debug output.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
/sys/module/acpi/parameters/debug_layers used to contain only the
debug layers defined by the ACPI CA. This patch adds the additional
layer definitions for ACPI drivers.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Move all the component definitions for drivers to a single shared place,
include/acpi/acpi_drivers.h.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
breakage introduced by following patch
commit 27663c5855
Author: Matthew Wilcox <willy@linux.intel.com>
Date: Fri Oct 10 02:22:59 2008 -0400
acpi_evaluate_integer() does not clear passed variable if
there is an error at evaluation.
So if we ignore error, we must supply initialized variable.
http://bugzilla.kernel.org/show_bug.cgi?id=11917
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
Since commit bc45b1d39a acpi tables are
allowed to have an empty signature and /sys/firmware/acpi/tables uses the
signature as filename. Applications using naive recursion through /sys
loop forever. A possible solution would be: (replacing the zero length
filename with the string "NULL")
http://bugzilla.kernel.org/show_bug.cgi?id=11539
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Impact: cleanup
Use MACRO for rev 3 fadt id instead of 3 directly.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch is part of a larger patch series which will remove
the "char bus_id[20]" name string from struct device. The device
name is managed in the kobject anyway, and without any size
limitation, and just needlessly copied into "struct device".
To set and read the device name dev_name(dev) and dev_set_name(dev)
must be used. If your code uses static kobjects, which it shouldn't
do, "const char *init_name" can be used to statically provide the
name the registered device should have. At registration time, the
init_name field is cleared, to enforce the use of dev_name(dev) to
access the device name at a later time.
We need to get rid of all occurrences of bus_id in the entire tree
to be able to enable the new interface. Please apply this patch,
and possibly convert any remaining remaining occurrences of bus_id.
We want to submit a patch to -next, which will remove bus_id from
"struct device", to find the remaining pieces to convert, and finally
switch over to the new api, which will remove the 20 bytes array
and does no longer have a size limitation.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-Off-By: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Associating a Local SAPIC with a processor object is dependent upon the
processor object's definition type. CPUs declared as "Processor" should
use the Local SAPIC's 'processor_id', and CPUs declared as "Device"
should use the 'uid'. Note that for "Processor" declarations, even if a
'_UID' child object exists, it has no bearing with respect to mapping
Local SAPICs (see section 5.2.11.13 - Local SAPIC Structure; "Advanced
Configuration and Power Interface Specification", Revision 3.0b).
This patch changes the lsapic mapping logic to rely on the distinction of
how the processor object was declared - the mapping can't just try both
types of matches regardless of declaration type and rely on one failing
as is currently being done.
Signed-off-by: Myron Stowe <myron.stowe@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Declaring processors in ACPI namespace can be done using either a
"Processor" definition or a "Device" definition (see section 8.4 -
Declaring Processors; "Advanced Configuration and Power Interface
Specification", Revision 3.0b). Currently the two processor
declaration types are conflated.
This patch disambiguates the processor declaration's definition type
enabling subsequent code to behave uniquely based explicitly on the
declaration's type.
Signed-off-by: Myron Stowe <myron.stowe@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove CONFIG_ACPI_EC. It was always set the same as CONFIG_ACPI,
and it had no menu label, so there was no way to set it to anything
other than "y".
Per section 6.5.4 of the ACPI 3.0b specification,
OSPM must make Embedded Controller operation regions, accessed
via the Embedded Controllers described in ECDT, available before
executing any control method.
The ECDT table is optional, but if it is present, the above text
means that the EC it describes is a required part of the ACPI
subsystem, so CONFIG_ACPI_EC=n wouldn't make sense.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove CONFIG_ACPI_POWER. It was always set the same as CONFIG_ACPI,
and it had no menu label, so there was no way to set it to anything
other than "y".
The interfaces under CONFIG_ACPI_POWER (acpi_device_sleep_wake(),
acpi_power_transition(), etc) are called unconditionally from the
ACPI core, so we already depend on it always being present.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_cm_sbs_init() doesn't do anything, so we can just remove it.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
I don't think there's any point in cluttering the code with these.
Better to improve the documentation so *anybody* can figure out
what layer & level to use.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Introduce a new flag showing whether the event has an event handler/method.
For all the GPEs and Fixed Events,
1. ACPI_EVENT_FLAG_HANDLE is cleared, it's an "invalid" ACPI event.
2. Both ACPI_EVENT_FLAG_HANDLE and ACPI_EVENT_FLAG_DISABLE are set,
it's "disabled".
3. Both ACPI_EVENT_FLAG_HANDLE and ACPI_EVENT_FLAG_ENABLE are set,
it's "enabled".
4. Both ACPI_EVENT_FLAG_HANDLE and ACPI_EVENT_FLAG_WAKE_ENABLE are set,
it's "wake_enabled".
Among other things, this prevents incorrect reporting of ACPI events
as being "invalid" when it's really just (temporarily) "disabled".
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Len Brown <len.brown@intel.com>
On some laptops the Fan device is turned on/off by controlling the
corresponding power resource. For example: If the power resource
defined in _PR0 object is turned off, it indicates that the FAN device
is in off state(the ACPI state is in D3 state).
Maybe the device is already in D3 state and expected to be transited to
D3 state. As there is no _PR3 object, the power transition can't be
finished and it will be switched to the Unknown state.
Maybe it is more reasonable that the strick check in power transistion
is deleted.
http://bugzilla.kernel.org/show_bug.cgi?id=9485
Signed-off-by: yakui.zhao@intel.com
Signed-off-by: Len Brown <len.brown@intel.com>
Currently not always an EV_SYN event is reported to userland
after the EV_SW SW_LID event has been sent. This is easy to verify
by using “input-events” from input-utils and just closing and opening
the lid.
Signed-off-by: Guillem Jover <guillem.jover@nokia.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When trying to build 2.6.28-rc1 on ia64, make aborts with:
CC drivers/acpi/processor_perflib.o
drivers/acpi/processor_perflib.c:41:28: error: asm/cpufeature.h: No such file or directory
drivers/acpi/processor_perflib.c: In function ‘acpi_processor_get_performance_info’:
drivers/acpi/processor_perflib.c:364: error: implicit declaration of function ‘boot_cpu_has’
drivers/acpi/processor_perflib.c:364: error: ‘X86_FEATURE_EST’ undeclared (first use in this function)
drivers/acpi/processor_perflib.c:364: error: (Each undeclared identifier is reported only once
drivers/acpi/processor_perflib.c:364: error: for each function it appears in.)
make[2]: *** [drivers/acpi/processor_perflib.o] Error 1
make[1]: *** [drivers/acpi] Error 2
make: *** [drivers] Error 2
this patch fix it.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Acked-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (123 commits)
dock: make dock driver not a module
ACPI: fix ia64 build warning
ACPI: hack around sysfs warning with link order
ACPI suspend: fix build warning when CONFIG_ACPI_SLEEP=n
intel_menlo: fix build warning
panasonic-laptop: fix build
ACPICA: Update version to 20080926
ACPICA: Add support for zero-length buffer-to-string conversions
ACPICA: New: Validation for predefined ACPI methods/objects
ACPICA: Fix for implicit return compatibility
ACPICA: Fixed a couple memory leaks associated with "implicit return"
ACPICA: Optimize buffer allocation procedure
ACPICA: Fix possible memory leak, error exit path
ACPICA: Fix fault after mem allocation failure in AML parser
ACPICA: Remove unused ACPI register bit definition
ACPICA: Update version to 20080829
ACPICA: Fix possible memory leak in acpi_ns_get_external_pathname
ACPICA: Cleanup for internal Reference Object
ACPICA: Update comments - no functional changes
ACPICA: Update for Reference ACPI_OPERAND_OBJECT
...
To avoid dock driver is loaded after other drivers like libata, let's
make dock driver not a module.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
There exists the following warning message will appear after the
following commit is merged.
>commit f2e969acd6d5981e6b1272810002558650d0736e
>Author: Zhao Yakui <yakui.zhao@intel.com>
>Date: Mon Aug 11 14:57:50 2008 +0800
>ACPI: Add "acpi.power_nocheck=1" to disable power state check in
power transition:
>WARNING: at linux-2.6/fs/sysfs/dir.c:463 sysfs_add_one+0x33/0x39()
>sysfs: duplicate filename 'acpi' can not be created
>kobject_add_internal failed for acpi with -EEXIST, don't try to register
things with the same name in the same directory
In the above commit the "acpi.power_nocheck" module parameter is defined
in drivers/acpi/power.c file. As several module parameters using the same ACPI
prefix are defined in the different files(for example: power_nocheck is
defined in drivers/acpi/power.c,debug_layer/debug_level are defined in
drivers/acpi/debug.c) and there exists another module between them, the
warning message will be printed when using the current generic param code.
(In the function of param_sysfs_init).
In fact when ACPI is selected, the drivers/acpi/power will also be compiled
as built-in kernel.So this issue can be fixed by the following approach.
workaround it by adjusting the module link order in drivers/acpi/Makefile.
In such case the module parameter using the same prefix(ACPI) are put together
in the param data section.
Of course the better solution is to fix it in generic param code related
with sysfs.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
