Commit Graph

882 Commits

Author SHA1 Message Date
Jean-Christophe PLAGNIOL-VILLARD
82015c4eae ARM: at91: add Shutdown Controller (SHDWC) DT support
Use a string to specific the wakeup mode to make it more readable.

Add the Real-time Clock Wake-up support too for sam9g45 and sam9x5.
Add AT91_SHDW_CPTWK0_MAX to specific the Max of the Wakeup Counter.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2012-03-15 23:38:02 +08:00
Jean-Christophe PLAGNIOL-VILLARD
a7776ec625 ARM: at91: add ram controller DT support
We can now drop the call to ioremap_registers() as we have the binding for the
SDRAM/DDR Controller.

Drop ioremap_registers() for sam9x5 too.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2012-03-15 23:37:56 +08:00
Jean-Christophe PLAGNIOL-VILLARD
c8082d344a ARM: at91: add RSTC (Reset Controller) dt support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2012-03-15 23:31:22 +08:00
Jean-Christophe PLAGNIOL-VILLARD
eb5e76ffd4 ARM: at91: add pmc DT support
Specified the main Oscillator via clock binding.
This will allow to do not hardcode it anymore in the DT board at 12MHz.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2012-03-15 23:31:14 +08:00
Jean-Christophe PLAGNIOL-VILLARD
8bf7ec6508 ARM: at91/dt: add Calao DAB-MMX daugther board support for USB-A9G20
http://www.calao-systems.com/articles.php?lng=en&pg=6099

this daughter board add the following device:
 - Micro-SD socket
 - TTL 3V3 - (Tx/Rx/RTS/CTS)
 - I2C port
 - 0.96" Serial OLED Display Module (over UART)
 - MP3 decoder with Micro & Speakers
 - 4x PB, 4x Leds (Blue), 3x Leds (Green, Orange, Red)

for now we add only the 2 UARTs, 4 Buttons, 7 leds and i2c via DT

used_led1 will not be re-add via DT as it's used by the motherboard too

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2012-03-15 23:29:54 +08:00
Jean-Christophe PLAGNIOL-VILLARD
10f71c28b6 ARM: at91: sam9x5 add i2c DT support
For now on use i2c-gpio driver on the same pin as the hardware IP.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
2012-03-15 23:29:48 +08:00
Jean-Christophe PLAGNIOL-VILLARD
8f24bdaac9 ARM: at91: sam9g45 add i2c DT support
For now on use i2c-gpio driver on the same pin as the hardware IP.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
2012-03-15 23:29:43 +08:00
Jean-Christophe PLAGNIOL-VILLARD
b71e1b75d6 ARM: at91: usb_a9g20 add DT i2c support
Use i2c-gpio and enable rv3029 RTC.

Enable the rtc in the sam9g20 defconfig.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
2012-03-15 23:29:39 +08:00
Jean-Christophe PLAGNIOL-VILLARD
3b3f828039 ARM: at91: sam9g20 add i2c DT support
For now on use i2c-gpio driver on the same pin as the hardware IP.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
2012-03-15 23:29:32 +08:00
Jean-Christophe PLAGNIOL-VILLARD
86a89f4ff6 ARM: at91: sam9x5 add nand support
Enable the nand in the cpu module with the partition.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2012-03-15 23:29:19 +08:00
Jean-Christophe PLAGNIOL-VILLARD
d6a016616b atmel/nand: add DT support
Use a local copy of board informatin and fill with DT data.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
2012-03-15 23:29:12 +08:00
Kukjin Kim
b074abb719 ARM: dts: add initial dts file for EXYNOS5250, SMDK5250
This patch adds initial dts file for EXYNOS5250 SoC. This dts
file is including the SoC specific devices and properties. And
adds the dts file for SMDK5250 board which uses the EXYNOS5250
dts file. Its board specific properites will be added later.

Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2012-03-14 22:22:12 -07:00
Rajendra Nayak
b3431f5ba4 arm/dts: OMAP3: Add mmc controller nodes and board data
Add OMAP mmc related device tree data for OMAP3.
Currenly limited to only omap3-beagle board.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
2012-03-14 21:54:57 +01:00
Rajendra Nayak
7498176803 arm/dts: OMAP4: Add mmc controller nodes and board data
Add OMAP mmc related device tree data for OMAP4.
Currenly limited to only omap4-panda and omap4-sdp
boards.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
2012-03-14 21:48:51 +01:00
Marc Zyngier
58458e0327 ARM: imx6q: convert to twd_local_timer_register() interface
Add support for the new smp_twd runtime registration interface
to the imx6q platforms, and remove the old compile-time support.

The imx6q DTS file is updated to match the TWD DT documentation.
Also present in this patch a DTS fix to the timer interrupt routing
(the PPI connection uses bits [15:8]) and trigger (rising edge).

Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2012-03-13 13:45:53 +00:00
Marc Zyngier
7ac9b9eb33 ARM: highbank: convert to twd_local_timer_register() interface
Add support for the new smp_twd runtime registration interface
to the highbank platforms, and remove the old compile-time support.

The highbank DTS file is updated to match the TWD DT documentation
and fixes the timer trigger (rising edge).

Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2012-03-13 13:45:52 +00:00
Rajendra Nayak
ecc7b060a7 arm/dts: twl: Pass regulator data from dt
Pass all the voltage regulator information for
twl6030/twl4030 PMIC from device tree.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
2012-03-12 23:42:22 +01:00
Benoit Cousson
e7c64db9f5 arm/dts: omap4-sdp: Add ks8851 ethernet SPI device
Add an ethernet SPI chip in the OMAP4 SDP/Blaze board DTS file.

Add a fixed regulator node controlled by a GPIO line to supply
the ethernet chip.

Based on original code from Rajendra.

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
2012-03-12 14:58:27 +01:00
Benoit Cousson
fc72d248d0 arm/dts: OMAP3: Add SPI controller nodes
Add the 4 McSPI controller nodes present in an OMAP3 device.

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
2012-03-12 14:58:26 +01:00
Benoit Cousson
efcf1e5020 arm/dts: OMAP4: Add SPI controller nodes
Add the 4 McSPI controller nodes present in an OMAP4 device.

Remove SPI static device initialisation if DT is populated.

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
2012-03-12 14:58:25 +01:00
Benoit Cousson
385a64bbc2 arm/dts: OMAP3: Add gpio nodes
Add the 6 GPIOs controller nodes present in OMAP3.

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
2012-03-12 14:58:24 +01:00
Benoit Cousson
e3e5a92db4 arm/dts: OMAP4: Add gpio nodes
Add the 6 GPIOs controller nodes present in OMAP4.

Remove gpio static device initialisation if DT is populated.

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
2012-03-12 14:58:22 +01:00
Olof Johansson
cdc3df6f44 Merge branch 'dt-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
* 'dt-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  arm/dts: mt_ventoux: very basic support for TeeJet Mt.Ventoux board
  ARM: OMAP2+: Remove extra ifdefs for board-generic
  ARM: OMAP2+: Fix build error when only ARCH_OMAP2/3 or 4 is selected
  ARM: OMAP2+: board-generic: Use of_irq_init API
  arm/dts: OMAP3: Add interrupt-controller bindings for INTC
  ARM: OMAP2/3: intc: Add DT support for TI interrupt controller
2012-03-10 09:11:31 -08:00
Olof Johansson
a58f67e70a Merge branch 'dt' of git://github.com/hzhuang1/linux into next/dt
* 'dt' of git://github.com/hzhuang1/linux: (6 commits)
  Document: devicetree: add OF documents for arch-mmp
  ARM: dts: append DTS file of pxa168
  ARM: mmp: append OF support on pxa168
  ARM: mmp: enable rtc clk in pxa168
  i2c: pxa: add OF support
  serial: pxa: add OF support

  (plus update to v3.3-rc6)
2012-03-08 09:27:07 -08:00
Simon Glass
0a428036df arm: tegra: dts: Mark USB1 as an OTG port on Seaboard
The USB1 port on Tegra2 supports operation in host or device modes. On
Seaboard this is possible, so mark the port as OTG.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
2012-03-07 14:36:56 -08:00
Simon Glass
ba202f15cd arm: tegra: dts: Add legacy mode support to Tegra2x USB1 port
Tegra's USB1 port supports legacy mode, so mark it as such. Even if we
don't use it, we must turn it off in the driver.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
2012-03-07 14:36:52 -08:00
Benoit Cousson
5340b51d78 arm/dts: omap3-beagle: Add twl4030 and i2c EEPROM
Add required clock frequencies for the i2c client devices existing
on beagle board.

Add the twl4030 basic description with only the twl_rtc module.

Add the EEPROM node.

Based on original patch from Manju:
http://www.spinics.net/lists/linux-omap/msg55831.html

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
2012-03-07 13:43:20 +01:00
Benoit Cousson
33632ae750 arm/dts: omap4-sdp: Add twl6030, i2c3 and i2c4 devices
Update DTS file with required clock frequencies
for the i2c client devices existing on sdp4430.

Add the twl6030 node inside the i2c1 controller node.
This is the minimal support needed to boot OMAP4 boards
without any crash.
The support for all the features included in this MFD will be
added later.

Add the RTC submodule inside the twl node.

Add tmp105 temperature sensor in i2c3
Add bh1780 Ambient Light Sensor in i2c3
Add hmc5843 3-Axis Digital Compass in i2c4

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
2012-03-07 13:43:20 +01:00
Benoit Cousson
898ee397c3 arm/dts: omap4-panda: Add twl6030 and i2c EEPROM
Update pandaboard dts file with required clock frequencies
for the i2c client devices existing on pandaboard.

Add the twl6030 node in i2c1 controller.

This is the minimal support needed to boot OMAP4 boards
without any crash.
The support for all the features included in this MFD will be
added later.

Add a generic i2c EEPROM entry.

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
2012-03-07 13:43:18 +01:00
Benoit Cousson
dce90d596d arm/dts: twl4030: Add DTS file for twl4030 PM + Audio IC
Add a dedicated DTS file for the twl4030/5030 Power + Audio IC.
This chip is a big SoC that will be reused in a lot of various
OMAP3 boards.

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
2012-03-07 13:43:17 +01:00
Benoit Cousson
4711244c76 arm/dts: twl6030: Add DTS file for twl6030 PMIC
Add a dedicated DTS file for the twl6030 Power IC.
This chip is a big SoC that will be reused in a lot of various
OMAP4+ boards.

Note: This file is supposed to be included in a board DTS that will
create the twl node in order to allow the &twl reference to work.

Exmaple:
...
&i2c1 {
    twl: twl@48 {
        reg = <0x48>;
        interrupts = <0 7 4>;
        interrupt-controller;
        interrupt-parent = <&gic>;
    };
};

/include/ "twl6030.dtsi"
...

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
2012-03-07 13:43:16 +01:00
Haojian Zhuang
10d77ec21a ARM: dts: append DTS file of pxa168
DTS files of both PXA168 and aspenite are appended.

Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
2012-03-07 09:32:40 +08:00
Ilya Yanok
328ae2cb50 arm/dts: mt_ventoux: very basic support for TeeJet Mt.Ventoux board
Very basic support for TeeJet Mt.Ventoux board. Able to boot via
board-generic and ramdisk/initramfs, however most of peripherals are
not supported. Produces tons of twl4030 related errors as this board
doesn't have twl4030 installed.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2012-03-05 13:48:03 -08:00
Arnd Bergmann
2eed4e7d86 Merge tag 'tegra-boards' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra into tegra/boards
Tegra board updates. Most of the board updates for tegra30 and for some
of the driver device-tree conversions have gone in through the other
branches, so that leaves quite little left here -- mostly a couple
of updates to the not-yet-converted tegra2 boards and a couple of
device-tree updates.

* tag 'tegra-boards' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra:
  ARM: tegra: match SoC name not board name in DT board files
  ARM: tegra: PCIe: Provide 3.3V supply voltage
  ARM: dt: tegra: add the wifi led to paz00 device tree
  ARM: dt: tegra: add the power gpio key to paz00 device tree
  ARM: dt: tegra: add ADT7461 temperature sensor to paz00 device tree

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-03-04 21:22:33 +00:00
Arnd Bergmann
7cb7f82611 Merge tag 'tegra-soc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra into tegra/soc-drivers
Tegra SoC driver support.

Some device tree conversions, some new drivers. and a fix for an issue
introduced in Grant Likely's irq_domain conversion in his tree. Because
of that, this branch depends on his branch to build (but not to merge):

git://git.secretlab.ca/git/linux-2.6.git irqdomain/next

* tag 'tegra-soc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra: (34 commits)
  ARM: tegra: uncompress.h: Don't depend on kernel headers
  gpio: tegra: Fix build issue due to irq_domain rework.
  ARM: tegra: Remove duplicate PMU interrupt inversion code
  ARM: tegra: Add a simple PMC driver
  ARM: tegra: dma: not required to move requestor when stopping.
  ARM: tegra: Fix EMC pdata initialization from registers
  gpio: tegra: Parameterize the number of banks
  gpio: tegra: Dynamically allocate IRQ base, and support DT
  ARM: tegra: Remove use of TEGRA_GPIO_TO_IRQ
  ARM: tegra: Pass uncompress.h UART selection to DEBUG_LL
  ARM: tegra: uncompress.h: Choose a UART at runtime
  ARM: tegra: uncompress.h: Store UART address in a variable
  ARM: tegra: Introduce define DEBUG_UART_SHIFT
  ARM: tegra: Support Tegra30 in decompressor UART setup
  ARM: tegra: Pause DMA when reading transfer count
  ARM: tegra: emc: device tree support
  ARM: tegra: emc: convert tegra2_emc to a platform driver
  ARM: tegra: fuse: add bct strapping reading
  ARM: tegra: fuse: add functions to access chip revision
  ARM: tegra: fuse: use apbio dma for register access
  ...

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-03-04 21:03:30 +00:00
Arnd Bergmann
4c6c826b22 Merge tag 'tegra-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra into tegra/dt
Device tree updates for tegra. Various development, including a handful
of additions to the tegra30 device trees.

* tag 'tegra-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra:
  ASoC: DT: Add digital microphone binding to PAZ00 board.
  ARM: dt: Add ARM PMU to tegra*.dtsi
  ARM: dt: Add SD controller configuration to Tegra Cardhu
  ARM: dt: tegra: Enable headset autodetection on PAZ00 board.
  ARM: dt: tegra: Enable device tree audio codec on PAZ00 board.
  ARM: dt: Add binding for Tegra PMC
  ARM: dt: tegra: Enable audio on WM8903 boards, disable others
  ARM: dt: tegra: Add labels for I2S controllers
  ARM: dt: tegra: Modify I2S nodes to match binding
  ARM: dt: tegra: Add Tegra APB DMA device tree binding
  ARM: dt: tegra30.dtsi: Add extra GPIO interrupt
  ARM: dt: tegra30.dtsi: Reformat gpio's interrupts property
  dt: tegra gpio: Flesh out binding documentation
  ARM: tegra: seaboard: add EMC table to device tree
  ARM: tegra: emc: device tree bindings

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-03-04 20:54:04 +00:00
Stephen Warren
8c690fdf46 ARM: dt: Explicitly configure all serial ports on Tegra Cardhu
The ports are used as follows:
UART1/A: Routed to debug dongle
UART2/B: GPS
UART3/C: Bluetooth
UART4/D: Routed to debug dongle
UART5/E: Not connected

The debug dongle has jumpers to connect either UART1/A or UART4/D to
the DB-9 connector. UART1/A is typically used on Cardhu, and is the option
we assume here.

For now, only enable UART1/A, and explicitly disable all other ports.

The explicit disable prevents the message "of_serial 70006040.serial:
no clock-frequency property set" being printed during boot.

Enabling the other ports requires their clocks to be enabled, or accesses
to the registers will hang. At present, this requires adding entries into
board-dt-tegra30.c's tegra_dt_clk_init_table[]. Lets punt on that and wait
for the common clock bindings to set this all up, although that will also
requiring adding clock support to 8250.c.

While we're at it, fix board-dt-tegra30.c to enable the correct clock for
the debug UART. We got away with this before, because the bootloader already
enabled it.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2012-03-04 10:47:30 -08:00
Leon Romanovsky
96d6714ca2 ASoC: DT: Add digital microphone binding to PAZ00 board.
This patch adds device tree binding of digital microphone to PAZ00
board.

Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Olof Johansson <olof@lixom.net>
2012-03-04 10:42:16 -08:00
Stephen Warren
583553b28c ARM: dt: Add ARM PMU to tegra*.dtsi
This enables HW performance measurements, and usage of the "perf" tool.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2012-03-04 10:41:57 -08:00
Arnd Bergmann
fcd2a8e945 Merge branch 'features/imx27-dt' of git://git.pengutronix.de/git/imx/linux-2.6 into next/dt
* 'features/imx27-dt' of git://git.pengutronix.de/git/imx/linux-2.6:
  devicetree-bindings: Add documentation for i.MX generic boards
  ARM i.MX: Add phytec phycore-i.MX27 (aka pcm038) devicetree support
  ARM i.MX27: Add devicetree support
2012-03-02 14:46:47 +00:00
Arnd Bergmann
48b3b08e00 Merge branch 'at91-3.4-cleanup2+DT' of git://github.com/at91linux/linux-at91 into next/dt
* 'at91-3.4-cleanup2+DT' of git://github.com/at91linux/linux-at91: (22 commits)
  ARM: at91: at91sam9x5cm/dt: add leds support
  ARM: at91: usb_a9g20/dt: add gpio-keys support
  ARM: at91: at91sam9m10g45ek/dt: add gpio-keys support
  ARM: at91: at91sam9m10g45ek/dt: add leds support
  ARM: at91: usb_a9g20/dt: add leds support
  ARM: at91/pio: add new PIO3 features
  ARM: at91: add sam9_smc.o to at91sam9x5 build
  ARM: at91/tc/clocksource: Add 32 bit variant to Timer Counter
  ARM: at91/tc: add device tree support to atmel_tclib
  ARM: at91/tclib: take iomem size from resource
  ARM: at91/pit: add traces in case of error
  ARM: at91: pit add DT support
  ARM: at91: AIC and GPIO IRQ device tree initialization
  ARM: at91/board-dt: remove AIC irq domain from board file
  ARM: at91/gpio: remove the static specification of gpio_chip.base
  ARM: at91/gpio: add .to_irq gpio_chip handler
  ARM: at91/gpio: non-DT builds do not have gpio_chip.of_node field
  ARM: at91/gpio: add irqdomain and DT support
  ARM: at91/gpio: change comments and one variable name
  ARM/USB: at91/ohci-at91: remove the use of irq_to_gpio
  ...
2012-03-02 13:22:28 +00:00
Arnd Bergmann
6e1d521b9d Merge branches 'depends/irqdomain' and 'at91/base2+cleanup' into next/dt
These two branches are a dependency for the at91 device tree changes,
so we pull them in here. at91/base2+cleanup will get merged through
the arm-soc cleanup2 branch, while the irqdomain tree will be sent
by Grant before this one gets integrated.

Conflicts:
	drivers/rtc/rtc-at91sam9.c

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-03-02 13:22:19 +00:00
Jean-Christophe PLAGNIOL-VILLARD
f75622f467 ARM: at91: at91sam9x5cm/dt: add leds support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2012-03-01 22:34:22 +08:00
Jean-Christophe PLAGNIOL-VILLARD
2ea332dedc ARM: at91: usb_a9g20/dt: add gpio-keys support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2012-03-01 22:34:21 +08:00
Jean-Christophe PLAGNIOL-VILLARD
8a087b0c15 ARM: at91: at91sam9m10g45ek/dt: add gpio-keys support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2012-03-01 22:34:20 +08:00
Jean-Christophe PLAGNIOL-VILLARD
f2ee7acd3d ARM: at91: at91sam9m10g45ek/dt: add leds support
Use the gpio for d7 as we do not support yet the pwm led via dt.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2012-03-01 22:34:20 +08:00
Jean-Christophe PLAGNIOL-VILLARD
4ea2565399 ARM: at91: usb_a9g20/dt: add leds support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2012-03-01 22:34:19 +08:00
Nicolas Ferre
582d5fbd4e ARM: at91/pio: add new PIO3 features
This patch adds the support for new PIO controller found on some
at91sam SOCs.
- more peripheral multiplexing
- more features to configure on a PIO (pull-down, Schmitt trigger, debouncer)
- support for several IRQ triggering features (type and polarity)

Support for those new features are retrieved from the device tree
compatibility string.

Debugfs at91_gpio file is updated to monitor configuration.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2012-03-01 13:38:50 +01:00
Nicolas Ferre
3a61a5dae4 ARM: at91/tc: add device tree support to atmel_tclib
Device tree support added to atmel_tclib: the generic Timer Counter
library. This is used by the clocksource/clockevent driver tcb_clksrc.

The current DT enabled platforms are also modified to use it:
- .dtsi files are modified to add Timer Counter Block entries
- alias are created to allow identification of each block
- clkdev lookup tables are added for clocks identification.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
2012-03-01 13:38:48 +01:00
Jean-Christophe PLAGNIOL-VILLARD
23fa648fd3 ARM: at91: pit add DT support
Retreive registers address and IRQ from device tree entry.
Called from at91_dt_init_irq() so that timers are up-n-running
when timers initialization will occur.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: change error path and interrupts property handling]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2012-03-01 13:38:36 +01:00
Nicolas Ferre
21f8187278 ARM: at91/gpio: add irqdomain and DT support
Add "legacy" type of irqdomain to preserve old-style numbering
and allow smooth transition for both DT and non-DT cases.

Original idea and code by Jean-Christophe Plagniol-Villard.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2012-03-01 13:29:01 +01:00
Nicolas Ferre
e261501d05 ARM: at91/aic: add irq domain and device tree support
Add an irqdomain for the AIC interrupt controller.
The device tree support is mapping the registers and
is using the irq_domain_add_legacy() to manage hwirq
translation.
The documentation is describing the meaning of the
two cells required for using this "interrupt-controller"
in a device tree node.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2012-03-01 13:29:00 +01:00
Arnd Bergmann
590d829a7c Merge branch 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
* 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  arm/dts: Add support for TI OMAP3 EVM board
  arm/dts: OMAP4: Update DTS file with new GIC bindings
  arm/dts: OMAP3: Add i2c controller nodes
  arm/dts: OMAP4: Add i2c controller nodes
  ARM: OMAP2+: Set Kconfig dependencies for PROC_DEVICETREE
  arm/dts: OMAP3&4: Remove the '0x' prefix for serial nodes
  ARM: OMAP1: kconfig: Enable IRQ_DOMAIN by default for OMAP1 platforms
  ARM: OMAP2+: pm: Do not init statically the SR and voltage layer with DT
  ARM: OMAP2+: omap_device: Replace dev_warn by dev_dbg in omap_device_build_from_dt
  ARM: OMAP2+: board-generic: Remove un-needed .atag_offset for DT_MACHINE
  ARM: OMAP2+: kconfig: Enable devicetree by default for OMAP2+ systems
  arm/dts: OMAP: Remove bootargs node from board files
2012-02-29 21:08:48 +00:00
Sascha Hauer
10a9ba059d ARM i.MX: Add phytec phycore-i.MX27 (aka pcm038) devicetree support
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2012-02-29 09:16:49 +01:00
Sascha Hauer
9f0749e3eb ARM i.MX27: Add devicetree support
This patch adds basic devicetree support for i.MX27 based SoCs.
Only the bindings for which drivers exist are added here:

- UART
- fec
- CSPI
- I2C
- watchdog
- gpio

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2012-02-29 09:15:09 +01:00
Arnd Bergmann
fb0b82b32c Merge branch 'board-specific' of git://github.com/hzhuang1/linux into next/boards
* 'board-specific' of git://github.com/hzhuang1/linux: (5 commits)
  ARM: pxa: add dummy clock for pxa25x and pxa27x
  ARM: mmp: append irq name of gpio device
  pxa/hx4700: Fix PXA_GPIO_IRQ_BASE/IRQ_NUM values
  pxa/hx4700: Add ASIC3 LED support
  pxa/hx4700: Correct StrataFlash block size discovery

(update to v3.3-rc5)
2012-02-28 12:42:21 +00:00
Arnd Bergmann
abf45ce84c Merge branch 'imx/defconfig' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/soc
* 'imx/defconfig' of git://git.linaro.org/people/shawnguo/linux-2.6: (2 commits)
  ARM: defconfig: imx_v6_v7: build in REGULATOR_FIXED_VOLTAGE
  ARM: imx: update imx_v6_v7_defconfig

(upadte to v3.3-rc5)
2012-02-28 12:33:46 +00:00
Arnd Bergmann
e0e5ce59dc Merge branch 'imx/dt' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
* 'imx/dt' of git://git.linaro.org/people/shawnguo/linux-2.6: (7 commits)
  ARM: dts: imx6q-sabrelite: add vmmc-supply for usdhc
  ARM: dts: imx6q-arm2: add vmmc-supply for usdhc
  ARM: dts: imx51-babbage: update mc13892 device
  ARM: dts: imx6q-sabrelite: add sgtl5000 audio codec
  ARM: dts: imx6q-sabrelite: add 2p5v and 3p3v regulators
  ARM i.MX5/6: Add dt support for generic boards
  ARM: imx5: generate dtbs for imx5 boards

(update to Linux 3.3-rc5)
2012-02-28 12:26:10 +00:00
Jason Cooper
759a45185a ARM: kirkwood: convert uart0 to devicetree.
This uart is the primary console for the dreamplug.  Removed
kirkwood_uart0_init() call from board-dt.c.

Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-02-27 16:21:44 +00:00
Jason Cooper
3d468b6d60 ARM: kirkwood: add dreamplug (fdt) support.
Initially, copied guruplug-setup.c and did s/guruplug/dreamplug/g.
Then, switched to SPI based NOR flash.

After talking to Arnd Bergman, chose an incremental approach to adding
devicetree support.  First, we use the dtb to tell us we are on the
dreamplug, then we gradually port over drivers.

Driver porting will start with the uart (see next patch), and progress
from there.  Possibly, spi/flash/partitions will be next.

When done, board-dt.c will no longer be dreamplug specific, and dt's can
be made for the other kirkwood boards.

Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-02-27 16:21:40 +00:00
Benoit Cousson
d65c542354 arm/dts: OMAP3: Add interrupt-controller bindings for INTC
Update the DTS with the proper information required by the
INTC bindings.

- Add the number of interrupt lines
- Add the reg and the compatible entries.

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
2012-02-27 10:33:19 +01:00
Shawn Guo
6f6ea93705 ARM: dts: imx6q-sabrelite: add vmmc-supply for usdhc
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2012-02-27 17:15:12 +08:00
Shawn Guo
648162ac18 ARM: dts: imx6q-arm2: add vmmc-supply for usdhc
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2012-02-27 17:13:27 +08:00
Shawn Guo
4619fce2c5 ARM: dts: imx51-babbage: update mc13892 device
It adds regulators, removes invalid property fsl,mc13xxx-uses-regulator,
and fixes interrupt for mc13892.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2012-02-27 14:59:37 +08:00
Richard Zhao
adcec4ce96 ARM: dts: imx6q-sabrelite: add sgtl5000 audio codec
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2012-02-27 14:53:48 +08:00
Richard Zhao
cf37a8ee60 ARM: dts: imx6q-sabrelite: add 2p5v and 3p3v regulators
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2012-02-27 14:53:29 +08:00
Olof Johansson
0f830e5c90 Merge branch 'for-3.4/soc-drivers' into for-3.4/t30-smp
Conflicts:
	arch/arm/mach-tegra/Makefile
2012-02-26 14:43:43 -08:00
Stephen Warren
850c4c8f9d ARM: dt: Add SD controller configuration to Tegra Cardhu
Cardhu uses Tegra's SD ports as follows:
SDMMC1: User SD slot, with GPIOs for power, CD, and WP.
SDMMC2: Not used
SDMMC3: WiFi (currently disabled pending future investigation)
SDMMC4: Internal eMMC

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2012-02-26 13:48:11 -08:00
Tony Lindgren
ffd76d8be3 Merge branch 'for_3.4/dts_updates' of git://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt into dt 2012-02-24 16:48:27 -08:00
Vaibhav Hiremath
f0e15e2b0c arm/dts: Add support for TI OMAP3 EVM board
Add OMAP3 EVM (OMAP3530, AM/DM37x) DTS file to use the omap3.dtsi SoC file,
along with memory node information.

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
2012-02-24 22:42:21 +01:00
Benoit Cousson
958e767645 arm/dts: OMAP4: Update DTS file with new GIC bindings
The GIC binding was updated in 3.2 and expects 3 interrupt-cells.
- Update the #interrupt-cells

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
2012-02-24 22:28:52 +01:00
Benoit Cousson
ca59a5c110 arm/dts: OMAP3: Add i2c controller nodes
Add i2c controllers nodes into the main ocp bus.

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
2012-02-24 22:27:02 +01:00
Benoit Cousson
58e778f9ce arm/dts: OMAP4: Add i2c controller nodes
Add i2c controllers nodes into the main ocp bus.

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
2012-02-24 22:26:39 +01:00
Pawel Moll
059289b260 ARM: vexpress: Add Device Tree for V2P-CA15 core tile (TC1 variant)
This patch adds Device Tree file for the CoreTile Express A15x2
(V2P-CA15) with Test Chip 1.

As the chip's GIC has 160 interrupt inputs and equivalent SMM
(FPGA) has GIC synthesised with 256 interrupts, NR_IRQS is
increased.

Signed-off-by: Pawel Moll <pawel.moll@arm.com>
2012-02-24 09:18:21 +00:00
Pawel Moll
cca070a916 ARM: vexpress: Add Device Tree for V2P-CA9 core tile
This patch adds Device Tree file for the CoreTile Express A9x4 (V2P-CA9).

Signed-off-by: Pawel Moll <pawel.moll@arm.com>
2012-02-24 09:18:21 +00:00
Pawel Moll
bfd5200c16 ARM: vexpress: Add Device Tree for V2P-CA5s core tile
This patch adds Device Tree file for the CoreTile Express A5x2 (V2P-CA5s).

Signed-off-by: Pawel Moll <pawel.moll@arm.com>
2012-02-24 09:18:20 +00:00
Pawel Moll
6a3719562b ARM: vexpress: Motherboard RS1 memory map support
This patch adds support for RS1 memory map based Versatile Express
motherboard.

Signed-off-by: Pawel Moll <pawel.moll@arm.com>
2012-02-24 09:18:20 +00:00
Pawel Moll
8deed1786a ARM: vexpress: Add Device Tree support
This patch adds generic Versatile Express DT machine description,
Device Tree description for the motherboard and documentation for
the bindings.

Signed-off-by: Pawel Moll <pawel.moll@arm.com>
2012-02-24 09:18:19 +00:00
Tony Lindgren
4d68c05ce1 Merge branch 'for_3.4/dt_base' of git://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt into dt 2012-02-17 15:12:36 -08:00
Benoit Cousson
19bfb76ca3 arm/dts: OMAP3&4: Remove the '0x' prefix for serial nodes
Follow the DTS convention and thus name the nodes <name>@<address> without
any '0x' prefix in the physical address.

Suggested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
2012-02-16 23:07:06 +01:00
Arnd Bergmann
ffafe770a4 Merge branch 'v3.3-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
* 'v3.3-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (2 commits)
  ARM: EXYNOS: Add cpu-offset property in gic device tree node
  ARM: EXYNOS: Bring exynos4-dt up to date
  Linux 3.3-rc3

This includes an update to the v3.3-rc3 release from v3.3-rc2

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-02-13 05:50:26 +00:00
Thomas Abraham
da911782be ARM: EXYNOS: Add cpu-offset property in gic device tree node
Commit db0d4db22a ('ARM: gic: allow GIC to support non-banked setups)
requires a cpu-offset property to be specified for non-banked gic
controllers, which is the case for Exynos4.

Reported-and-Tested-by: Karol Lewandowski <k.lewandowsk@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2012-02-09 18:40:22 +09:00
Marc Dietrich
80c9473dc1 ARM: dt: tegra: add the wifi led to paz00 device tree
This adds the wifi led bound to the rfkill0 event to the device
tree of paz00.

Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
2012-02-06 21:10:15 -08:00
Marc Dietrich
d8d56c8422 ARM: dt: tegra: add the power gpio key to paz00 device tree
This adds the wakeup gpio which is connected to the embedded
controller to the device tree of paz00.

Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
2012-02-06 21:09:25 -08:00
Marc Dietrich
1266f8970e ARM: dt: tegra: add ADT7461 temperature sensor to paz00 device tree
Add the ADT7461 temperature monitoring IC which is connected via
the DVC controller.

Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2012-02-06 21:08:43 -08:00
Marc Dietrich
0783a9bf4a ARM: tegra: paz00: fix wrong UART port on mini-pcie plug
UARTC is connected to the mini-pcie port.

Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2012-02-06 18:32:51 -08:00
Marc Dietrich
5f21f1240c ARM: tegra: paz00: fix wrong SD1 power gpio
The power gpio for the external memory card was specified wrongly.
Replace it with the correct value (tested with warmboot with fastboot).

Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2012-02-06 18:32:50 -08:00
Stephen Warren
6f74dc9bc8 gpio: tegra: Dynamically allocate IRQ base, and support DT
Enhance the driver to dynamically allocate the base IRQ number, and
create an IRQ domain for itself. The use of an IRQ domain ensures that
any device tree node interrupts properties are correctly parsed.

Describe interrupt-related properties in the device tree binding docs,
and the contents of "child" node interrupts property.

Update tegra*.dtsi to specify the required interrupt-related properties.

Finally, remove the definition of TEGRA_GPIO_TO_IRQ; this macro no longer
gives correct results since the IRQ numbers for GPIOs are dynamically
allocated.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Olof Johansson <olof@lixom.net>
2012-02-06 18:25:00 -08:00
Leon Romanovsky
07d4563e58 ARM: dt: tegra: Enable headset autodetection on PAZ00 board.
This patch is adding device tree support of headset autodetection on PAZ00 board.

Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Olof Johansson <olof@lixom.net>
2012-02-06 18:21:51 -08:00
Leon Romanovsky
613e9657df ARM: dt: tegra: Enable device tree audio codec on PAZ00 board.
This patch adds initial device tree support of ALC5632 sound codec and
machine driver for PAZ00 board. The implementation is based on the WM8903 codec.

Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Olof Johansson <olof@lixom.net>
2012-02-06 18:21:42 -08:00
Stephen Warren
d17adfdb17 ARM: dt: Add binding for Tegra PMC
The Tegra PMC (Power Management Controller) interfaces with an external
PMU (Power Management Unit), and controls wake-up from sleep modes.

This initial binding is the bare minimum required to control the PMC's
inversion of the PMU's interrupt signal.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2012-02-06 18:21:21 -08:00
Stephen Warren
797acf705b ARM: dt: tegra: Enable audio on WM8903 boards, disable others
Add complete bindings to instantiate and configure the codec and
top-level audio complex on all currently supported boards using the
Tegra+WM8903 audio driver.

On those boards, disable the I2S2 controller since it isn't used.

On boards not using the WM8903 codec, disable all the audio devices;
they can be re-enabled once the relevant codec and ASoC machine drivers
have been ported to device-tree.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2012-02-06 18:21:21 -08:00
Stephen Warren
c404af0a16 ARM: dt: tegra: Add labels for I2S controllers
This will allow the sound node to refer to the I2S controllers by name
when creating phandles.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2012-02-06 18:21:21 -08:00
Stephen Warren
5c8ee3120e ARM: dt: tegra: Modify I2S nodes to match binding
Adjust the dma-channel property name to match the binding implemented by
the driver. The binding was implemented and documented in a
separate change to the ASoC tree.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2012-02-06 18:21:20 -08:00
Stephen Warren
8051b75ab3 ARM: dt: tegra: Add Tegra APB DMA device tree binding
Document binding, and add the node to tegra*.dtsi.

The driver isn't actually instantiated from this node yet, but the I2S
binding will rely on being able to refer to the APB DMA node using a
phandle.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2012-02-06 18:21:20 -08:00
Stephen Warren
f8196b01b9 ARM: dt: tegra30.dtsi: Add extra GPIO interrupt
The Tegra30 GPIO controller has one more bank than Tegra20, and hence
has one more interrupt.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Olof Johansson <olof@lixom.net>
2012-02-06 18:21:19 -08:00
Stephen Warren
636e50a0e0 ARM: dt: tegra30.dtsi: Reformat gpio's interrupts property
The new content matches tegra20.dtsi, and is < 80 columns.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Olof Johansson <olof@lixom.net>
2012-02-06 18:21:19 -08:00
Olof Johansson
d8017a975c ARM: tegra: seaboard: add EMC table to device tree
Timings for the T25 version of seaboard, only one memory manufacturer
and timing table (two speeds).

Signed-off-by: Olof Johansson <olof@lixom.net>
2012-02-06 18:21:18 -08:00
Olof Johansson
0c6700abfa ARM: tegra: emc: device tree bindings
Device tree bindings for the EMC tables on tegra.

Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
2012-02-06 18:21:18 -08:00
Nicolas Ferre
467f1cf504 ARM: at91/at91sam9x5: Device tree definition files
Device tree include file for the AT91SAM9x5 SoC family.
An additional .dtsi file is created to describe the generic
SAM9x5 CPU Module (CM).
Device tree source files for each Evaluation Kit that are using
the generic CPU Module and the carrier board. The selection of
available peripherals is done in this .dts file.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2012-02-03 15:36:41 +01:00
Grant Likely
7aff0fe330 of: Add of_property_match_string() to find index into a string list
Add a helper function for finding the index of a string in a string
list property.  This helper is useful for bindings that use a separate
*-name property for attaching names to tuples in another property such
as 'reg' or 'gpios'.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2012-01-28 10:29:20 -07:00
Linus Torvalds
b3c3752292 power management changes for omap and imx
A significant part of the changes for these two platforms went into
 power management, so they are split out into a separate branch.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIVAwUATwtaEmCrR//JCVInAQIUqBAAkqKDGCyKmC2nDfz5ejYNUvugkDxgYv5I
 fl9UUfBc2cLDVyOynzjH9SLTphVAI8jZa0KZAlvB8/+4Wcg7XNhUFPDH868zlPzP
 mSsPPTnb3WJTqb1PLKi7oTbA7CfsX/srRaAtrEX7Nng7uGTZZq+5RL6mOR/bqHyR
 F/VuV5U9HkDjgM7T7NtcNMqP9ysHDSrcNDse62yKh8FLot59rqXEEXZWTIYZphbI
 v+BURp4EHs5Wm5AVJbpGmWhk4+NgRCLE0ZKZlfxnJctFz5+bW11TX/85ua+UXtmt
 Fnij44jSmAzbQ1o0VLbN760iBsbPN/JElYWXwIqR6v5M+Hd2UDRm3a6Bc1xqUNx0
 0C8DEoo78XebhldAsN1TL/V94j1ojuNyWC7qkn9VBZLTiVYPyV/oeIdxtR19u1lB
 QctpXeUPCfdDyD+wAWbqid0MExayP3TAwJ5vK8Tw+ssIv3A19RkUI6kdGaW4RqyL
 5n5o7Ze4CGOzrthWuyfw5flKbjRUrmtLO6TTgPZKCwxeiQh3G1GJcCL6lKbGbH3M
 Z8jNWzEMMExZU+55P8hRrtNgnx6rqn2bWi/3cCSmuKB6KHBUWXfKJw3rmTcWOsLB
 aNSXqYoWtTK9hJ0zo1xIAGmnJlfrO9I66abCuHHjDKVh1W5j7zmZwrj4ErUuS/dO
 UHOmrQN/GOY=
 =P4kO
 -----END PGP SIGNATURE-----

Merge tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

power management changes for omap and imx

A significant part of the changes for these two platforms went into
power management, so they are split out into a separate branch.

* tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (65 commits)
  ARM: imx6: remove __CPUINIT annotation from v7_invalidate_l1
  ARM: imx6: fix v7_invalidate_l1 by adding I-Cache invalidation
  ARM: imx6q: resume PL310 only when CACHE_L2X0 defined
  ARM: imx6q: build pm code only when CONFIG_PM selected
  ARM: mx5: use generic irq chip pm interface for pm functions on
  ARM: omap: pass minimal SoC/board data for UART from dt
  arm/dts: Add minimal device tree support for omap2420 and omap2430
  omap-serial: Add minimal device tree support
  omap-serial: Use default clock speed (48Mhz) if not specified
  omap-serial: Get rid of all pdev->id usage
  ARM: OMAP2+: hwmod: Add a new flag to handle hwmods left enabled at init
  ARM: OMAP4: PRM: use PRCM interrupt handler
  ARM: OMAP3: pm: use prcm chain handler
  ARM: OMAP: hwmod: add support for selecting mpu_irq for each wakeup pad
  ARM: OMAP2+: mux: add support for PAD wakeup interrupts
  ARM: OMAP: PRCM: add suspend prepare / finish support
  ARM: OMAP: PRCM: add support for chain interrupt handler
  ARM: OMAP3/4: PRM: add functions to read pending IRQs, PRM barrier
  ARM: OMAP2+: hwmod: Add API to enable IO ring wakeup
  ARM: OMAP2+: mux: add wakeup-capable hwmod mux entries to dynamic list
  ...
2012-01-09 14:39:59 -08:00
Linus Torvalds
2ac9d7aacc Driver specific changes
Again, a lot of platforms have changes in here: pxa, samsung, omap,
 at91, imx, ...
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIVAwUATwtZUmCrR//JCVInAQL93hAAzBbSkswA4SD09UXHPSLGpbWd7JYuax9T
 sR17FvnQCV+0T8c7ORRbjoBrCrxKkxuPMkFrfIHuTaP+beYe13CwTf2mV+dtnuv2
 hSjSjdgCq+yv+CvRZhRnmHqmEePN1dvRoC9Q/EVPEibJNJ4BjrTALMfkXbsTz861
 BOmcD7VGi0YfPhwRQ3D00MjohCflRoV2EmceHCUvH4HLEgpWcWl16UZeuWGn6BiA
 GJK37O2ubKz0hkExAH6NHEaRxeFsapjh8kkR8/dOoNh/iIlmmR5SRPOxMPWFD0ui
 lUeSc6QjMipHCzkfE7jUx6MICDZfRx+WRWVTwa/OTLJjJtY+zcRnUvoLl84XJqgX
 EG5YhyL+Os4Z0ci92uSK3rwYQ2AJz/r4dS6VWnAVVJHSc8zHCuioJL4KcF81llcz
 1dshlHkB1H1EeVrf08OM/1xX0X7SNzVJlQ801OZj31DYYtMqvrev72vn+tvJh6kL
 o9gZsOSl3cIlFi8cAK0WmZmwGHw4wfUDZb1ojN6GDctdrp/Vmwe3exHleWvfSDtN
 QBw4WyHl46JGw4bFVQ4hRH3vJZNuiso+ZNZvG3qGaEMfpNY5aMTy7lrxI/GFbFkA
 tEnhkDgjutEZ/B6nEF1h8cCrcLND7u4n209kJh6UR1Qx3a6xD/M/ycE4tisNuPE3
 wSSYuM1ZGTU=
 =vPhu
 -----END PGP SIGNATURE-----

Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Driver specific changes

Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...

* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
  ARM: sa1100: clean up of the clock support
  ARM: pxa: add dummy clock for sa1100-rtc
  RTC: sa1100: support sa1100, pxa and mmp soc families
  RTC: sa1100: remove redundant code of setting alarm
  RTC: sa1100: Clean out ost register
  Input: zylonite-wm97xx - replace IRQ_GPIO() with gpio_to_irq()
  pcmcia: pxa: replace IRQ_GPIO() with gpio_to_irq()
  ARM: EXYNOS: Modified files for SPI consolidation work
  ARM: S5P64X0: Enable SDHCI support
  ARM: S5P64X0: Add lookup of sdhci-s3c clocks using generic names
  ARM: S5P64X0: Add HSMMC setup for host Controller
  ARM: EXYNOS: Add USB OHCI support to ORIGEN board
  USB: Add Samsung Exynos OHCI diver
  ARM: EXYNOS: Add USB OHCI support to SMDKV310 board
  ARM: EXYNOS: Add USB OHCI device
  net: macb: fix build break with !CONFIG_OF
  i2c: tegra: Support DVC controller in device tree
  i2c: tegra: Add __devinit/exit to probe/remove
  net/at91_ether: use gpio_is_valid for phy IRQ line
  ARM: at91/net: add macb ethernet controller in 9g45/9g20 DT
  ...
2012-01-09 14:39:22 -08:00
Linus Torvalds
5ede3ceb7b New feature development
This adds support for new features, and contains stuff from most
 platforms. A number of these patches could have fit into other
 branches, too, but were small enough not to cause too much
 confusion here.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIVAwUATwtYgGCrR//JCVInAQKzRRAAybELlfOIT1fyVlzkzIgw0/OKxS75Vqda
 v5mNYUfQ001WxGjwbFGgFphrQgyhulmLj6gN5l1rwaBjEZlwLe5uk3sReeqeDMLk
 bERLbpg22ymka4JVhvugq5qh9UP2ptlvZV/cAZC0u2JBq+CaarFIJsrzbOyXAngf
 4kUkaMhKi8DDZTqrwwACaLxR7qtf3ddiSxNLZ93X4fDh4a3qs/EJErVg/xCFlfM3
 YTzTjKuqLV2cGT34E9YTJieN9o94G+PiqvbDsP3kOwG2dSElpRWsZwX/0hDoyCxN
 cWbqPfrrdzt/kDcNnNd8MZ16AJlPc4ElVVEWPF71tKP3HfKqtZ0vMlpzsldioFz6
 8AKvaXJXRkRddY4KqNcXeEQHcDxO0uniG/3lhZY8NlzO/1PnPQ4hGl8fhw+e/2z0
 nAQFUsCVIXacsxamPk/fFBUhYzyK7JrnH4pB3b7SPcCj7X9MVyWK+pbT5LA+VGOL
 Ys8tv3NtTWEObyW1s3NT+BEy9FkkRu4EG3TxPwHUXk4BTwa6nDmJBPjk7Hv7q4cn
 T58lPet8Aylhht2aZx+0dxK3MHtMOmgsJ5jQF0OAi48Kmx8kXPZ1AeXObROncbZL
 aI7qfuGTzps7MlUBYlmrMdceTfYLeOqIEoVyFX8N4xLE33alk8DMKc37QoTJVuxQ
 KrY8sCVMkK0=
 =N2B4
 -----END PGP SIGNATURE-----

Merge tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

New feature development

This adds support for new features, and contains stuff from most
platforms. A number of these patches could have fit into other
branches, too, but were small enough not to cause too much
confusion here.

* tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
  mfd/db8500-prcmu: remove support for early silicon revisions
  ARM: ux500: fix the smp_twd clock calculation
  ARM: ux500: remove support for early silicon revisions
  ARM: ux500: update register files
  ARM: ux500: register DB5500 PMU dynamically
  ARM: ux500: update ASIC detection for U5500
  ARM: ux500: support DB8520
  ARM: picoxcell: implement watchdog restart
  ARM: OMAP3+: hwmod data: Add the default clockactivity for I2C
  ARM: OMAP3: hwmod data: disable multiblock reads on MMC1/2 on OMAP34xx/35xx <= ES2.1
  ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP4
  ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3
  ARM: OMAP: hwmod data: Add support for AM35xx UART4/ttyO3
  ARM: Orion: Remove address map info from all platform data structures
  ARM: Orion: Get address map from plat-orion instead of via platform_data
  ARM: Orion: mbus_dram_info consolidation
  ARM: Orion: Consolidate the address map setup
  ARM: Kirkwood: Add configuration for MPP12 as GPIO
  ARM: Kirkwood: Recognize A1 revision of 6282 chip
  ARM: ux500: update the MOP500 GPIO assignments
  ...
2012-01-09 14:38:51 -08:00
Linus Torvalds
6d889d03ab Board-level changes
This adds and extends support for specific boards on a number of
 ARM platforms:  omap, imx, samsung, tegra, ...
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIVAwUATwtXvWCrR//JCVInAQKWjw/+IgL536c+ksAfIFLvQpDq0cV1J4xdGoqT
 AdpK4bp3ze3c5HduweyZ6tKun9Shfg3/wuJH5ZwoJDzfRpF1DpALJDSZxRfll/y9
 x7FbiVS8Kw+UJ02J1Z4jC4pguXtiUFGn9ebUI5V4wt5N8/xawFuWQ/6QybfmBSwP
 ZvZa0sONEZwIPMMRO1/Q31z7jotBhcx9vYorUu4xyTx8yRK2DLD1eZENa107KuVA
 0TQFreaGVvTgfLGTXy7wH41/VEKNj5qMOIBgpswLfQh85D0wXbZ98FsUt34t+r2D
 9XUg8nkNUbmTQ/NokiVgqoju0UVNmjITIjQWFV/3qmhlQo5kO8tKJV+qmVMkw49b
 VaazO/VpbY2+8ucHaTMKlnInUVwOOvlTRX8QJjOmyRWqYmk190jWYUtpsq9Xbt49
 h/U9Grz+koFpDmAZTyscm3Zlub9U9YYvnjrA8UnbxpCeBpE2qy2+UIucnF1hTf7K
 zn+kHvot4glubbRqLYhda3g+xomBf+xfvoGhFyutno2pBOm04Jd8E9ZQzkvxMnPn
 w2S8Lo78KtKXVcbZbQDRW5UhaiRnu969P0gX2PcSSeTNn7FZF4FME1RB+CXbWazx
 G4pfOfoso573m1UXjf/ueAdZU4H63WEMgULuXdzwmSlTZ97Lk5+sb+NHCPg5p4cA
 6QHbmogFraA=
 =lYb/
 -----END PGP SIGNATURE-----

Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Board-level changes

This adds and extends support for specific boards on a number of
ARM platforms:  omap, imx, samsung, tegra, ...

* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (49 commits)
  Enable 32 bit flash support for iMX21ADS board
  ARM: mx31pdk: Add MC13783 RTC support
  iomux-mx25: configuration to support CSPI3 on CSI pins
  MX1:apf9328: Add i2c support
  mioa701: add newly available DoC G3 chip
  arm/tegra: remove __initdata annotation from pinmux tables
  arm/tegra: Use bus notifiers to trigger pinmux setup
  arm/tegra: Refactor board-*-pinmux.c to share code
  arm/tegra: Fix mistake in Trimslice's pinmux
  arm/tegra: Rework Seaboard-vs-Ventana pinmux table
  arm/tegra: Remove useless entries from ventana_pinmux[]
  arm/tegra: PCIe: Remove include of mach/pinmux.h
  arm/tegra: Harmony PCIe: Don't touch pinmux
  arm/tegra: Add AUXDATA for tegra-pinmux and tegra-gpio
  arm/tegra: Split Seaboard GPIO table to allow for Ventana
  ARM: imx6q: generate imx6q dtb files
  arm/imx6q: Rename Sabreauto to Armadillo2
  arm/imx6q-sabrelite: add enet phy ksz9021rn fixup
  arm/imx6: add imx6q sabrelite board support
  dts/imx: rename uart labels to consistent with hw spec
  ...
2012-01-09 14:37:41 -08:00
Linus Torvalds
7400c12eb0 SoC-level changes for tegra and omap
This adds support for the new tegra30 SoC, as well as small
 changes to support minor variations of existing omap SoCs.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIVAwUATwtVn2CrR//JCVInAQKJZBAAud0Ug5o0+PsOsyH4y8N4OYBQyfkB6aVh
 5ClZkc83jMQRA+chjI/wFzYR+3BGz0nlzuVOe7r+YI8YQPAZjJgvMmgIAycfRdq9
 bNKEqd6i08RMqx9S7vxWaUzK4WOCTvbl9yvpCNp9EkbbDi2xsBWbv6X75hRNWLJB
 8uDlCCC9gfoo29kp+XjE0auqGlhUu8fPRHiviJlRUBYBeGuH03CZEHVn12joJMnK
 zDh+gSb3EuxI8Hd2vHJ6bwt7DexEXaHdsbQwF4SdtRjt5mMmu/xY7rvMGdK3lFJz
 /oR6OoKseJEJ+Tdx0OA6vXn+BOkIWEeHbMGfrpjnitATJCmXqeGk5vSSR7NDYmHC
 4qtqQ6NwcIIBBLiYhksuHv2bIkIbaB94mCge3Yf0s8NSHGZJTozTIrB1gtO0v8AX
 9cpBorIDbg9mIOiWCBR2wVgYOw6cCCUPAbF0JJ+/GMdkjetxITHjqEDzUYzlgPDD
 T+63U1HSRJyYzgMXEfW4WbshXILuFJSrHzHpPLWBJuCH3xdlmnKV1g/6lvia7V2f
 NMGwCvreWrOBa9FbGvtVamEoLFEyKCXZbFEvuN0kIJ6czCkcRq6EIsaXJL9s4iPk
 27mwCpCJvfc8c+ocCsVcWl/fWHtCXmeMeotmzdLA7/L6YIx8YdvY8RpgAXDv9jA7
 +dt4jW+tjEE=
 =hp8k
 -----END PGP SIGNATURE-----

Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

SoC-level changes for tegra and omap

This adds support for the new tegra30 SoC, as well as small
changes to support minor variations of existing omap SoCs.

* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
  arm/tegra: Compile tegra_dt_init_irq only when CONFIG_OF
  arm/tegra: Make MACH_TEGRA_DT depend on ARCH_TEGRA_2x_SOC
  arm/tegra: Delete tegra_init_clock()
  arm/tegra: Fix section mismatch errors in tegra30 pinmux
  arm/tegra: Fix section mismatch errors in tegra20 pinmux
  arm/tegra: refresh defconfig for tegra30
  arm/tegra: add support for tegra30 based board cardhu
  arm/tegra: implement support for tegra30
  arm/tegra: pinmux tables and definitions for tegra30
  arm/tegra: add new fields to struct tegra_pingroup_desc
  arm/tegra: prepare pinmux code for multiple tegra variants
  arm/tegra: rename tegra20 pinmux files
  arm/tegra: generalize L2 cache initialization
  arm/tegra: use PMC reset
  arm/tegra: rename board-dt.c to board-dt-tegra20.c
  arm/tegra: prepare early init for multiple tegra variants
  arm/tegra: don't export clk_measure_input_freq
  arm/tegra: prepare clock code for multiple tegra variants
  arm/tegra: cleanup tegra20 support
  arm/tegra: clk_get should not be fatal
  ...

Fix up trivial conflict in arch/arm/mach-tegra/board-dt-tegra20.c
2012-01-09 14:33:17 -08:00
Linus Torvalds
dfc1ebe766 Device tree conversions for samsung and tegra
Both platforms had some initial device tree support, but this adds
 much more to actually make it usable.
 
 This is where the really nasty conflicts in the samsung platform
 start, due to some files getting moved around and combined in the
 'restart' branch that has already gone into mainline through
 Russell's tree.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIVAwUATwtUpWCrR//JCVInAQI7bhAA1Q8MXyQ3EwLKMWX2p0vmbb29Nugoq0Y3
 u9pBlCqiz0zw/jccPWASCgVgMVYguZLuhvMRCO8Q1D4l3ljcTt7qhtN6lBAESz2N
 OTTaNU2T84Um2Watm7VAQrnLcJMhxd/wFV06lmE62SgxwIVzyqxo4sr3KB3S5Qyj
 W3q5wRLuc5pC293HkWSNpLj3nfcKFF2oHOFpEAC5AS/C5S38Eu/T9y4FSUGvoTq4
 u7xlZT11uZUTRfvkRQUTOXkh9I0Fk0JuwUpUkqhgvM4jD0Ehs60/702CX4mPAoVd
 +BFUI23QNSof6O04rUxEzOSt1ZNg4Le+pQZ3vUcOvi539Npq+VgzDU+yo7uzNtYv
 c22VJihvS9GY2s7ynmmCE6Rgw17B3VOMMy1cBbQEET2V2GwgU9lQLx2eR/bUrOGq
 ewcTCqgFFWVugsGsn0wM0BiPZAJ+FddXon3w3X09BM0v5a6O6q0aUAQiJnGqDgUE
 ZLHhYRoL87r2TU6J+3iutK3sDHQrvHkGAZdXX3H5hVWdfLWqnwGgLjT/NpBeUaWc
 g6nut7pFgVDCD4q4JUCa99XykgKGWRtSHAuHmJQsdZ24PzpXmse3etVZTCYwr7t6
 BM3zrozoecQbGTRwZKGb9poOKd7g7xJ7125770GqYgTeX+BnBcA2lIEDAkEKsLBR
 GaxJggw32Q0=
 =XY2N
 -----END PGP SIGNATURE-----

Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Device tree conversions for samsung and tegra

Both platforms had some initial device tree support, but this adds
much more to actually make it usable.

* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
  ARM: dts: Add intial dts file for EXYNOS4210 SoC, SMDKV310 and ORIGEN
  ARM: EXYNOS: Add Exynos4 device tree enabled board file
  rtc: rtc-s3c: Add device tree support
  input: samsung-keypad: Add device tree support
  ARM: S5PV210: Modify platform data for pl330 driver
  ARM: S5PC100: Modify platform data for pl330 driver
  ARM: S5P64x0: Modify platform data for pl330 driver
  ARM: EXYNOS: Add a alias for pdma clocks
  ARM: EXYNOS: Limit usage of pl330 device instance to non-dt build
  ARM: SAMSUNG: Add device tree support for pl330 dma engine wrappers
  DMA: PL330: Add device tree support
  ARM: EXYNOS: Modify platform data for pl330 driver
  DMA: PL330: Infer transfer direction from transfer request instead of platform data
  DMA: PL330: move filter function into driver
  serial: samsung: Fix build for non-Exynos4210 devices
  serial: samsung: add device tree support
  serial: samsung: merge probe() function from all SoC specific extensions
  serial: samsung: merge all SoC specific port reset functions
  ARM: SAMSUNG: register uart clocks to clock lookup list
  serial: samsung: remove all uses of get_clksrc and set_clksrc
  ...

Fix up fairly trivial conflicts in arch/arm/mach-s3c2440/clock.c and
drivers/tty/serial/Kconfig both due to just adding code close to
changes.
2012-01-09 14:28:38 -08:00
Arnd Bergmann
421b759b86 Merge branch 'samsung/cleanup' into next/boards
Conflicts:
	arch/arm/mach-imx/mach-imx6q.c
	arch/arm/mach-omap2/board-ti8168evm.c
	arch/arm/mach-s3c64xx/Kconfig
	arch/arm/mach-tegra/Makefile
	arch/arm/mach-tegra/board-dt-tegra20.c
	arch/arm/mach-tegra/common.c

Lots of relatively simple conflicts between the board
changes and stuff from the arm tree. This pulls in
the resolution from the samsung/cleanup tree, so we
don't get conflicting merges.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-01-09 17:06:36 +00:00
Arnd Bergmann
e067096c8d Merge branch 'tegra/soc' into next/boards
Conflicts:
	arch/arm/mach-tegra/board-harmony-pcie.c

To fix an internal merge conflict between the tegra/soc and tegra/boards
branches.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-01-06 23:09:14 +00:00
Arnd Bergmann
bd4b9ba4cf Merge branch 'samsung/cleanup' into next/drivers
Dependency for the samsung/drivers branch

Conflicts:
	arch/arm/mach-exynos/Makefile

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2011-12-28 00:18:10 +00:00
Arnd Bergmann
31b2a86845 Merge branch 'samsung/dt' into next/dt
* samsung/dt: (27 commits)
  ARM: dts: Add intial dts file for EXYNOS4210 SoC, SMDKV310 and ORIGEN
  ARM: EXYNOS: Add Exynos4 device tree enabled board file
  rtc: rtc-s3c: Add device tree support
  input: samsung-keypad: Add device tree support
  ARM: S5PV210: Modify platform data for pl330 driver
  ARM: S5PC100: Modify platform data for pl330 driver
  ARM: S5P64x0: Modify platform data for pl330 driver
  ARM: EXYNOS: Add a alias for pdma clocks
  ARM: EXYNOS: Limit usage of pl330 device instance to non-dt build
  ARM: SAMSUNG: Add device tree support for pl330 dma engine wrappers
  DMA: PL330: Add device tree support
  ARM: EXYNOS: Modify platform data for pl330 driver
  DMA: PL330: Infer transfer direction from transfer request instead of platform data
  DMA: PL330: move filter function into driver
  serial: samsung: Fix build for non-Exynos4210 devices
  serial: samsung: add device tree support
  serial: samsung: merge probe() function from all SoC specific extensions
  serial: samsung: merge all SoC specific port reset functions
  ARM: SAMSUNG: register uart clocks to clock lookup list
  serial: samsung: remove all uses of get_clksrc and set_clksrc
  ...
2011-12-27 23:21:28 +00:00
Arnd Bergmann
e195ffbe45 Merge branch 'tegra/soc' into next/soc
* tegra/soc:
  arm/tegra: Compile tegra_dt_init_irq only when CONFIG_OF
  arm/tegra: Make MACH_TEGRA_DT depend on ARCH_TEGRA_2x_SOC
  arm/tegra: Delete tegra_init_clock()
  arm/tegra: Fix section mismatch errors in tegra30 pinmux
  arm/tegra: Fix section mismatch errors in tegra20 pinmux
  arm/tegra: refresh defconfig for tegra30
  arm/tegra: add support for tegra30 based board cardhu
  arm/tegra: implement support for tegra30
  arm/tegra: pinmux tables and definitions for tegra30
  arm/tegra: add new fields to struct tegra_pingroup_desc
  arm/tegra: prepare pinmux code for multiple tegra variants
  arm/tegra: rename tegra20 pinmux files
  arm/tegra: generalize L2 cache initialization
  arm/tegra: use PMC reset
  arm/tegra: rename board-dt.c to board-dt-tegra20.c
  arm/tegra: prepare early init for multiple tegra variants
  arm/tegra: don't export clk_measure_input_freq
  arm/tegra: prepare clock code for multiple tegra variants
  arm/tegra: cleanup tegra20 support
  arm/tegra: clk_get should not be fatal

Conflicts:
	arch/arm/mach-tegra/board-dt-tegra20.c
2011-12-27 22:55:47 +00:00
Thomas Abraham
0561ceabd0 ARM: dts: Add intial dts file for EXYNOS4210 SoC, SMDKV310 and ORIGEN
Add initial dts file for EXYNOS4210 SoC. This dts file describes
the SoC specific devices and properties. Along with this, add dts
file for Samsung's SMDKV310 board and Insignal's ORIGEN board which
uses the EXYNOS4210 dts file and extends it to describe the board
specific properties.

Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2011-12-23 10:07:12 +09:00
Stephen Warren
f0d143065c arm/tegra: Seaboard: Add GPIO key device tree nodes
This brings all the GPIO key definitions from board-seaboard.c into
tegra-seaboard.dtsi.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2011-12-19 17:59:21 -08:00
Stephen Warren
401c9a50e7 arm/dt: Add ADT7461 to Seaboard
The ADT7461 is a temperature monitoring IC. One is present on the DVC
I2C bus on Seaboard.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2011-12-19 17:54:54 -08:00
Stephen Warren
0bc2ecb6e5 arm/dt: tegra: Use new compatible value for DVC I2C controller
Update the device tree to indicate which I2C controller is the DVC
controller. AUXDATA needs to be updated too, since the compatible
value changed.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2011-12-19 17:54:53 -08:00
Peter De Schrijver
64c4e9f898 arm/tegra: add support for tegra30 based board cardhu
Add support for the tegra30 based cardhu development board. Cardhu is a tablet
formfactor reference design for tegra30. The patch provides a device tree for
the board, updates Makefile.boot to build the dtb, includes the platform in
Kconfig and updates board-dt.c.

Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2011-12-17 20:15:38 -08:00
Peter De Schrijver
c3e00a0eff arm/tegra: initial device tree for tegra30
This patch adds the initial device tree for tegra30

Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2011-12-17 16:14:49 -08:00
Rajendra Nayak
cf3c79de2b ARM: omap: pass minimal SoC/board data for UART from dt
Pass minimal data needed for console boot, from dt, for
OMAP4 panda/sdp and OMAP3 beagle boards, and get rid of the
static initialization from generic board file.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-12-16 14:15:17 -08:00
Tony Lindgren
f20b933d2a arm/dts: Add minimal device tree support for omap2420 and omap2430
Add minimal device tree support for omap2420 and omap2430.

This is needed to keep the uart functional on omap2 after
omap_serial_init is removed from board-generic.c.

Reviewed-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-12-16 14:15:16 -08:00
Nicolas Ferre
0d4f99d8b7 ARM: at91/net: add macb ethernet controller in 9g45/9g20 DT
Add the Cadence macb ethernet controller in at91sam9g45 and at91sam9g20
.dtsi and enable it in at91sam9m10g45ek and usb_a9g20 board device tree file.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2011-12-16 13:11:09 +01:00
Dirk Behme
752baf5647 arm/imx6q: Rename Sabreauto to Armadillo2
The Sabreauto board was renamed to Armadillo2 recently. To avoid
confusion, rename Sabreauto to Armadillo2/arm2.

Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2011-12-14 21:25:46 +08:00
Richard Zhao
3c8276c6bc arm/imx6: add imx6q sabrelite board support
- Add basic board dts file
- Add board compatible string to mach-imx6q.
- Update fsl DT board doc.

Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2011-12-14 21:25:45 +08:00
Richard Zhao
8f9ffecfa9 dts/imx: rename uart labels to consistent with hw spec
UART1/UART2/... is more readable than UART0/UART1/... .
Remove redundant UART comments.

Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2011-12-14 21:25:44 +08:00
Richard Zhao
4d191868a6 dts/imx: rename gpio labels to consistent with hw spec
GPIO1/GPIO2/... is more readable than GPIO0/GPIO1/... .
Remove redundant gpio comments.

Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2011-12-14 21:25:43 +08:00
Benoit Cousson
fb49b8c22d arm/dts: OMAP: Remove bootargs node from board files
Since 3.2, the CONFIG_ARM_ATAG_DTB_COMPAT config allows
an old bootloader to still use ATAG to provide cmdline.

Remove chosen/bootargs from the DTS board files.

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-12-13 14:45:26 -08:00
Grant Likely
53a42093d9 of: Add device tree selftests
Add some runtime test cases for the library of device tree parsing functions.

v2: - Add testcase for phandle with 0 args
    - Don't run testcases if testcase data isn't present in device tree

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-12-12 13:40:16 -07:00
pdeschrijver@nvidia.com
0d4f74792e arm/tegra: convert tegra20 to GIC devicetree binding
Convert tegra20 IRQ intialization to the GIC devicetree binding. Modify the
interrupt definitions in the dts files according to
Documentation/devicetree/bindings/arm/gic.txt

v3 (swarren):
* Moved of_irq_init() call into board-dt.c to avoid ifdef'ing it.
  - Even with a dummy replacement if !CONFIG_OF, the reference from
    tegra_dt_irq_match[] to gic_of_init() would still have to be ifdef'd
  - It's plausible that tegra_dt_irq_match[] may need to contain more
    entries in the future, and defining what they are seems more suitable
    for board-dt.c than irq.c
v2 (swarren):
* Removed some stale GIC init code from board-dt.c
* Undid some accidental 0x -> 0x0 search/replace.

Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
[olof: added include of <asm/hardware/gic.h> for compile to pass]
Signed-off-by: Olof Johansson <olof@lixom.net>
2011-12-07 21:20:12 -08:00
Stephen Warren
1292c12959 arm/dt: tegra: Fix SDHCI nodes to match board files
Mark any SDHCI controllers that aren't registered by the board files as
disabled in the device-tree files.

In practice, these controllers:

* Have nothing hooked up to them at all, or
* For ports intended for SDIO usage, the drivers for anything that might
  be attached are not in the device-tree yet. If/when drivers appear, the
  SD/MMC port can be re-enabled.

The only possible exception is TrimSlice's mico SD slot, but that wasn't
enabled in the board files before anyway, and doesn't work when all the
SDHCI controllers are enabled anyway.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2011-12-07 20:48:06 -08:00
Stephen Warren
31c1ec9282 arm/dt: tegra: Fix serial nodes to match board files
Mark any serial ports that aren't registered by the board files as disabled
in the device-tree files.

In practice, none of the now-disabled ports ended up succeeding device
probing because of the missing clock-frequency property. However,
explicitly marking the devices disabled has the advantage of squashing
the dev_warn() the failed probe causes, and documenting that we intend
the port not to be used, rather than accidentally left out the property.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2011-12-07 20:48:05 -08:00
Stephen Warren
88950f3b6d arm/dt: tegra: Fix I2C nodes to match board files
With board files, all I2C busses run at 400KHz. Fix the device-tree
to be consistent with this. It's possible this is incorrect, but at
least it keeps the board files and device-tree consistent.

Also, disable any I2C controllers that the board files don't register,
also for consistency.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2011-12-07 20:48:04 -08:00
Stephen Warren
492f204da8 arm/dt: tegra: Remove /chosen node
The command-lines present in the existing /chosen node are not necessarily
correct for all users. Ideally, we should simply use the command-line
supplied by the boot-loader.

In fact, using the boot-loader's cmdline is quite easy; either the
bootloader fully supports DT, in which case it can modify the DT passed
to the kernel to include its command-line, or CONFIG_APPENDED_DTB can
be used in conjunction with CONFIG_ARM_ATAG_DTB_COMPAT, and the kernel
will substitute the bootloader's command-line into the DT.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2011-12-07 20:48:03 -08:00
Stephen Warren
5a85426506 arm/dt: tegra: Remove /memreserve/ from device-tree files
There are no drivers in the kernel at present which can make use of the
memory reserved by /memreserve/, so there is no point reserving it. Remove
/memreserve/ to allow the user more memory. It's also unclear whether any
future driver would actually require /memreserve/, or allocate memory
through some other mechanism.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2011-12-07 20:48:02 -08:00
Marc Dietrich
cc2afa43d4 arm/dt: tegra: add dts file for paz00
This adds a dts file for paz00. As a side effect, this also enables
the embedded controller which controls the keyboard, touchpad, power,
leds, and some other functions.

Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2011-12-07 20:47:50 -08:00
Stephen Warren
a7db2c1593 arm/tegra: Add device-tree support for TrimSlice board
* Add device-tree file for TrimSlice
* Add that to the list of .dts files to build
* Update board-dt.c to recognize TrimSlice board name

v2: Makefile: Add board-trimslice-pinmux.c to obj-$(CONFIG_MACH_TEGRA_DT).
v3: Makefile: Use brackets not braces around var names

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2011-12-07 20:47:49 -08:00
Stephen Warren
64f88ec395 arm/dt: tegra: Clean up I2S and DAS nodes
The I2S and DAS nodes don't have children, and hence don't need to set
address/size cells.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2011-12-07 20:47:48 -08:00
Olof Johansson
c27317c0ed arm/dt: add basic usb nodes to tegra device trees
For now they are a minimal binding. It needs to be amended with
vendor-specific settings for phy setup and link tuning, etc.

v2: Added bindings specification and phy_type properties

Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Stephen Warren <swarren@nvidia.com>
2011-12-07 20:47:47 -08:00
Rob Herring
bd0552ed05 ARM: highbank: add xgmac ethernet devices to dts
Add device nodes for xgmac ethernet block in Calxeda Highbank.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2011-12-05 08:35:55 -06:00
Stephen Warren
c406eeb3aa arm/dt: Fix ventana SDHCI power-gpios
Ventana uses the same SDHCI GPIOs as Seaboard; PI6 (70) is the power GPIO
for the SD port, and there is no power GPIO for the MMC chip.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2011-11-09 11:24:37 -08:00
Linus Torvalds
994c0e9925 Merge branch 'next/soc' of git://git.linaro.org/people/arnd/arm-soc
* 'next/soc' of git://git.linaro.org/people/arnd/arm-soc: (21 commits)
  MAINTAINERS: add ARM/FREESCALE IMX6 entry
  arm/imx: merge i.MX3 and i.MX6
  arm/imx6q: add suspend/resume support
  arm/imx6q: add device tree machine support
  arm/imx6q: add smp and cpu hotplug support
  arm/imx6q: add core drivers clock, gpc, mmdc and src
  arm/imx: add gic_handle_irq function
  arm/imx6q: add core definitions and low-level debug uart
  arm/imx6q: add device tree source
  ARM: highbank: add suspend support
  ARM: highbank: Add cpu hotplug support
  ARM: highbank: add SMP support
  MAINTAINERS: add Calxeda Highbank ARM platform
  ARM: add Highbank core platform support
  ARM: highbank: add devicetree source
  ARM: l2x0: add empty l2x0_of_init
  picoxcell: add a definition of VMALLOC_END
  picoxcell: remove custom ioremap implementation
  picoxcell: add the DTS for the PC7302 board
  picoxcell: add the DTS for pc3x2 and pc3x3 devices
  ...

Fix up trivial conflicts in arch/arm/Kconfig, and some more header file
conflicts in arch/arm/mach-omap2/board-generic.c (as per an ealier merge
by Arnd).
2011-11-01 21:08:03 -07:00
Linus Torvalds
367069f16e Merge branch 'next/dt' of git://git.linaro.org/people/arnd/arm-soc
* 'next/dt' of git://git.linaro.org/people/arnd/arm-soc:
  ARM: gic: use module.h instead of export.h
  ARM: gic: fix irq_alloc_descs handling for sparse irq
  ARM: gic: add OF based initialization
  ARM: gic: add irq_domain support
  irq: support domains with non-zero hwirq base
  of/irq: introduce of_irq_init
  ARM: at91: add at91sam9g20 and Calao USB A9G20 DT support
  ARM: at91: dt: at91sam9g45 family and board device tree files
  arm/mx5: add device tree support for imx51 babbage
  arm/mx5: add device tree support for imx53 boards
  ARM: msm: Add devicetree support for msm8660-surf
  msm_serial: Add devicetree support
  msm_serial: Use relative resources for iomem

Fix up conflicts in arch/arm/mach-at91/{at91sam9260.c,at91sam9g45.c}
2011-11-01 21:02:35 -07:00
Linus Torvalds
81a3c10ce8 Merge branch 'next/cleanup2' of git://git.linaro.org/people/arnd/arm-soc
* 'next/cleanup2' of git://git.linaro.org/people/arnd/arm-soc: (31 commits)
  ARM: OMAP: Warn if omap_ioremap is called before SoC detection
  ARM: OMAP: Move set_globals initialization to happen in init_early
  ARM: OMAP: Map SRAM later on with ioremap_exec()
  ARM: OMAP: Remove calls to SRAM allocations for framebuffer
  ARM: OMAP: Avoid cpu_is_omapxxxx usage until map_io is done
  ARM: OMAP1: Use generic map_io, init_early and init_irq
  arm/dts: OMAP3+: Add mpu, dsp and iva nodes
  arm/dts: OMAP4: Add a main ocp entry bound to l3-noc driver
  ARM: OMAP2+: l3-noc: Add support for device-tree
  ARM: OMAP2+: board-generic: Add i2c static init
  ARM: OMAP2+: board-generic: Add DT support to generic board
  arm/dts: Add support for OMAP3 Beagle board
  arm/dts: Add initial device tree support for OMAP3 SoC
  arm/dts: Add support for OMAP4 SDP board
  arm/dts: Add support for OMAP4 PandaBoard
  arm/dts: Add initial device tree support for OMAP4 SoC
  ARM: OMAP: omap_device: Add a method to build an omap_device from a DT node
  ARM: OMAP: omap_device: Add omap_device_[alloc|delete] for DT integration
  of: Add helpers to get one string in multiple strings property
  ARM: OMAP2+: devices: Remove all omap_device_pm_latency structures
  ...

Fix up trivial header file conflicts in arch/arm/mach-omap2/board-generic.c
2011-11-01 20:58:25 -07:00
Linus Torvalds
16ee792e45 Merge branch 'next/devel' of git://git.linaro.org/people/arnd/arm-soc
* 'next/devel' of git://git.linaro.org/people/arnd/arm-soc: (50 commits)
  ARM: tegra: update defconfig
  arm/tegra: Harmony: Configure PMC for low-level interrupts
  arm/tegra: device tree support for ventana board
  arm/tegra: add support for ventana pinmuxing
  arm/tegra: prepare Seaboard pinmux code for derived boards
  arm/tegra: pinmux: ioremap registers
  gpio/tegra: Convert to a platform device
  arm/tegra: Convert pinmux driver to a platform device
  arm/dt: Tegra: Add pinmux node to tegra20.dtsi
  arm/tegra: Prep boards for gpio/pinmux conversion to pdevs
  ARM: mx5: fix clock usage for suspend
  ARM i.MX entry-macro.S: remove now unused code
  ARM i.MX boards: use CONFIG_MULTI_IRQ_HANDLER
  ARM i.MX tzic: add handle_irq function
  ARM i.MX avic: add handle_irq function
  ARM: mx25: Add the missing IIM base definition
  ARM i.MX avic: convert to use generic irq chip
  mx31moboard: Add poweroff support
  ARM: mach-qong: Add watchdog support
  ARM: davinci: AM18x: Add wl1271/wlan support
  ...

Fix up conflicts in:
	arch/arm/mach-at91/at91sam9g45.c
	arch/arm/mach-mx5/devices-imx53.h
	arch/arm/plat-mxc/include/mach/memory.h
2011-11-01 20:31:25 -07:00
Linus Torvalds
cd9a0b6bd6 Merge branch 'next/pm' of git://git.linaro.org/people/arnd/arm-soc
* 'next/pm' of git://git.linaro.org/people/arnd/arm-soc: (66 commits)
  ARM: CSR: PM: use outer_resume to resume L2 cache
  ARM: CSR: call l2x0_of_init to init L2 cache of SiRFprimaII
  ARM: OMAP: voltage: voltage layer present, even when CONFIG_PM=n
  ARM: CSR: PM: add sleep entry for SiRFprimaII
  ARM: CSR: PM: save/restore irq status in suspend cycle
  ARM: CSR: PM: save/restore timer status in suspend cycle
  OMAP4: PM: TWL6030: add cmd register
  OMAP4: PM: TWL6030: fix ON/RET/OFF voltages
  OMAP4: PM: TWL6030: address 0V conversions
  OMAP4: PM: TWL6030: fix uv to voltage for >0x39
  OMAP4: PM: TWL6030: fix voltage conversion formula
  omap: voltage: add a stub header file for external/regulator use
  OMAP2+: VC: more registers are per-channel starting with OMAP5
  OMAP3+: voltage: update nominal voltage in voltdm_scale() not VC post-scale
  OMAP3+: voltage: rename omap_voltage_get_nom_volt -> voltdm_get_voltage
  OMAP3+: voltdm: final removal of omap_vdd_info
  OMAP3+: voltage: move/rename curr_volt from vdd_info into struct voltagedomain
  OMAP3+: voltage: rename scale and reset functions using voltdm_ prefix
  OMAP3+: VP: combine setting init voltage into common function
  OMAP3+: VP: remove unused omap_vp_get_curr_volt()
  ...

Fix up trivial conflict in arch/arm/mach-prima2/l2x0.c (code removal vs
edit)
2011-11-01 20:22:01 -07:00
Arnd Bergmann
abc3f126ac Merge branch 'imx/imx6q' into next/soc
Conflicts:
	Documentation/devicetree/bindings/arm/fsl.txt
	arch/arm/Kconfig
	arch/arm/Kconfig.debug
	arch/arm/plat-mxc/include/mach/common.h
2011-11-02 02:46:55 +01:00
Arnd Bergmann
b8df0ea26a Merge branch 'picoxcell/soc' into next/soc 2011-11-02 02:46:17 +01:00
Arnd Bergmann
884897e6a1 Merge branch 'highbank/soc' into next/soc
Conflicts:
	arch/arm/mach-mxs/include/mach/gpio.h
	arch/arm/mach-omap2/board-generic.c
	arch/arm/plat-mxc/include/mach/gpio.h
2011-11-02 02:46:10 +01:00
Shawn Guo
7d740f87fd arm/imx6q: add device tree source
It adds device tree source and documentation for imx6q platform.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2011-10-31 14:26:20 +01:00
Rob Herring
253d7addbc ARM: highbank: add devicetree source
This adds the devicetree source and documentation for the Calxeda highbank
platform.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
2011-10-31 14:13:58 +01:00
Arnd Bergmann
86c1e5a74a Merge branch 'omap/dt' into next/dt 2011-10-31 14:07:51 +01:00
Arnd Bergmann
6a8d2e2b50 Merge branches 'msm/dt', 'imx/dt' and 'at91/dt' into next/dt 2011-10-30 22:09:09 +01:00
Jean-Christophe PLAGNIOL-VILLARD
fea3158c55 ARM: at91: add at91sam9g20 and Calao USB A9G20 DT support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Rob Herring <rob.herring@calxeda.com>
2011-10-25 13:08:31 +02:00
Nicolas Ferre
49fe2ba313 ARM: at91: dt: at91sam9g45 family and board device tree files
Create a new device tree source file for Atmel at91sam9g45 SoC family.
The Evaluation Kit at91sam9m10g45ek includes it.
This first basic support will be populated as drivers and boards will be
converted to device tree.
Contains serial, dma and interrupt controllers.

The generic board file still takes advantage of platform data for early serial
init. As we need a storage media and the NAND flash driver is not converted to
DT yet, we keep old initialization for it.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Rob Herring <rob.herring@calxeda.com>
2011-10-25 13:08:21 +02:00
Barry Song
917d853564 ARM: CSR: call l2x0_of_init to init L2 cache of SiRFprimaII
Cc: Rob Herring <robherring2@gmail.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
2011-10-24 02:54:21 -07:00
Arnd Bergmann
1075329202 Merge branch 'tegra/devel' into next/devel 2011-10-20 18:15:30 +02:00
Arnd Bergmann
29ea35969b Merge branch 'imx/devel' into next/devel 2011-10-20 15:30:55 +02:00
Shawn Guo
9daaf31a8c arm/mx5: add device tree support for imx51 babbage
It adds device tree support for imx51 babbage board.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-10-18 12:43:19 +02:00
Shawn Guo
73d2b4cdfc arm/mx5: add device tree support for imx53 boards
It adds device tree support for imx53 boards.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-10-18 12:42:57 +02:00
Peter De Schrijver
add29e61d4 arm/tegra: device tree support for ventana board
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2011-10-13 15:04:54 -07:00
Stephen Warren
f62f548c1c arm/dt: Tegra: Add pinmux node to tegra20.dtsi
Add a pinmux node to tegra20.dtsi in order to instantiate the future
pinmux device.

v2: Specify reg property precisely; don't just point at the whole APB_MISC
register range.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2011-10-11 17:19:56 -07:00
Benoit Cousson
476b679a5d arm/dts: OMAP3+: Add mpu, dsp and iva nodes
Add nodes for devices used by PM code (mpu, dsp, iva).

Add a cpus node as well as recommended in the DT spec.

Remove mpu, dsp, iva devices init if is populated.

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Kevin Hilman <khilman@ti.com>
2011-10-04 22:29:40 +02:00
Benoit Cousson
ad8dfac66f arm/dts: OMAP4: Add a main ocp entry bound to l3-noc driver
Used the main OCP node to add bindings with the l3_noc driver.
Remove l3_noc static device creation if DT is populated.

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
2011-10-04 22:29:39 +02:00
Benoit Cousson
295e98c60b arm/dts: Add support for OMAP3 Beagle board
Add OMAP3 beagleboard DTS file to use the omap3.dtsi SoC file.

Add a default bootargs line to allow a boot from RAMDISK.

Add memory node information.

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>
2011-10-04 22:27:03 +02:00
Benoit Cousson
189892f496 arm/dts: Add initial device tree support for OMAP3 SoC
Add initial OMAP3 soc file with empty ocp bus.

Based on initial patch from Manju:
http://www.spinics.net/lists/linux-omap/msg55830.html

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>
2011-10-04 22:27:02 +02:00
Benoit Cousson
492beedfd8 arm/dts: Add support for OMAP4 SDP board
Add the SDP/Blaze (Software Development Board) support with
device tree.
That file is based on the omap4-panda.dts.

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>
2011-10-04 22:27:01 +02:00
Benoit Cousson
38eb2ae658 arm/dts: Add support for OMAP4 PandaBoard
Based on the original omap4-panda.dts file from Manju.
http://www.spinics.net/lists/linux-omap/msg55836.html

Add memory information and a default bootargs to allow
a boot from RAMDISK.

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>
2011-10-04 22:26:59 +02:00
Benoit Cousson
d9fda07af7 arm/dts: Add initial device tree support for OMAP4 SoC
Add initial device-tree support for OMAP4 SoC.

This is based on the original panda board patch done by Manju:
http://permalink.gmane.org/gmane.linux.ports.arm.omap/60393

Add the generic GIC interrupt-controller from ARM.

Add an empty "soc" node to contain non memory mapped IPs
(DSP, MPU, IPU...).

Note: Since reg, irq and dma are provided by hwmod for the
moment, these attributes will not be present at all in DTS
to highlight the gap. They will be added as soon as dma bindings
will be there and drivers will be adapted.

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>
2011-10-04 22:26:58 +02:00
Jamie Iles
a14bf143b3 picoxcell: add the DTS for the PC7302 board
The PC7302 board can be populated with either a PC3X2 or PC3X3 device.
Add DTS files for both variants of the PC7302.

v3:	- remove bootargs from dts files

Signed-off-by: Jamie Iles <jamie@jamieiles.com>
2011-09-26 16:12:07 +01:00
Jamie Iles
fee7565679 picoxcell: add the DTS for pc3x2 and pc3x3 devices
This describes the basic hierarchy of picoxcell pc3x3 devices including
clocks and bus interconnect.  Some onchip devices are currently omitted
as there haven't been bindings created for them.

v2:	- change timer compatible strings to be more soc specific
	- split vic node into 2 devices

Signed-off-by: Jamie Iles <jamie@jamieiles.com>
2011-09-26 16:12:06 +01:00
Stephen Warren
6111d50c58 arm/dt: Tegra: Add support-8bit to SDHCI nodes
For Seaboard's internal eMMC, this makes the difference between a
5.5MB/s and 10.2MB/s transfer rate. On Harmony, there wasn't any
measurable difference on my cheap/slow ~2MB/s card.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2011-09-22 14:44:28 +00:00
Stephen Warren
a0638eb6a2 arm/dt: Tegra: Update SDHCI nodes to match bindings
The bindings were recently updated to have separate properties for each
type of GPIO. Update the Device Tree source to match that.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2011-09-20 22:56:53 +02:00
Zhiwu Song
684f741446 ARM: CSR: add rtc i/o bridge interface for SiRFprimaII
The module is a bridge between the RTC clock domain and the CPU interface
clock domain. ARM access the register of SYSRTC, GPSRTC and PWRC through
this module.

Signed-off-by: Zhiwu Song <zhiwu.song@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
2011-09-11 09:17:53 +08:00
Barry Song
c915bedf22 ARM: CSR: extend the compatibility of gpio controller to pinmux in dts
gpio controller handles the switch of gpio and pinmux. And drivers/pinctrl/pinmux-sirf.c
will contain both gpio and pinmux.

Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
2011-09-11 09:14:15 +08:00
Barry Song
073adf4fa7 ARM: CSR: add lost Resource Sharing Control(RSC) node in dts
Signed-off-by: Barry Song <Baohua.Song@csr.com>
2011-09-11 09:13:32 +08:00
David Brown
56e2d8a688 ARM: msm: Add devicetree support for msm8660-surf
Adds support for booting via device tree with a simple serial console.

Change-Id: I7f175b8db21928cd13e0fb49f3eed74966a2696f
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
2011-08-29 12:47:36 -07:00
Arnd Bergmann
6124a4e430 Merge branch 'imx/dt' into next/dt 2011-07-28 15:25:46 +00:00
Grant Likely
8e267f3da5 arm/dt: tegra devicetree support
Everything required to populate NVIDIA Tegra devices from the device
tree.  This patch adds a new DT_MACHINE_DESC() which matches against
a tegra20 device tree.  So far it only registers the on-chip devices,
but it will be refined in follow on patches to configure clocks and
pin IO from the device tree also.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-07-28 01:32:04 -06:00
Grant Likely
3ba7222ac9 arm/versatile: Add device tree support
For testing the dt work, define a dt-enabled versatile platform.

This patch adds a new versatile platform for when using the device
tree.  Add platform and amba devices are discovered and registered by
parsing the device tree.  Clocks and initial io mappings are still
configured statically.

This patch still depends on some static platform_data for a few devices
which is passed via the auxdata structure to of_platform_populate(),
but it is a viable starting point until the drivers can get all
configuration data out of the device tree.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-07-28 01:32:04 -06:00
Grant Likely
2b4180af3f arm/dt: Add skeleton dtsi file
Contains the bare minimum template required to boot with the device tree.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-07-25 09:52:11 -06:00
Arnd Bergmann
3a6cb8ce07 Merge branch 'zynq/master' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc into next/soc
Conflicts:
	arch/arm/Kconfig
	arch/arm/mm/Kconfig
2011-07-17 21:43:26 +02:00
Binghua Duan
02c981c07b ARM: CSR: Adding CSR SiRFprimaII board support
SiRFprimaII is the latest generation application processor from CSR’s
Multifunction SoC product family. Designed around an ARM cortex A9 core,
high-speed memory bus, advanced 3D accelerator and full-HD multi-format
video decoder, SiRFprimaII is able to meet the needs of complicated
applications for modern multifunction devices that require heavy concurrent
applications and fluid user experience. Integrated with GPS baseband,
analog and PMU, this new platform is designed to provide a cost effective
solution for Automotive and Consumer markets.

This patch adds the basic support for this SoC and EVB board based on device
tree. It is following the ZYNQ of Xilinx in some degree.

Signed-off-by: Binghua Duan <Binghua.Duan@csr.com>
Signed-off-by: Rongjun Ying <Rongjun.Ying@csr.com>
Signed-off-by: Zhiwu Song <Zhiwu.Song@csr.com>
Signed-off-by: Yuping Luo <Yuping.Luo@csr.com>
Signed-off-by: Bin Shi <Bin.Shi@csr.com>
Signed-off-by: Huayi Li <Huayi.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
2011-07-09 07:19:28 +08:00
John Linn
b85a3ef4ac ARM: Xilinx: Adding Xilinx board support
The 1st board support is minimal to get a system up and running
on the Xilinx platform.

This platform reuses the clock implementation from plat-versatile, and
it depends entirely on CONFIG_OF support.  There is only one board
support file which obtains all device information from a device tree
dtb file which is passed to the kernel at boot time.

Signed-off-by: John Linn <john.linn@xilinx.com>
2011-06-20 11:52:30 -06:00