Put a 1000 msec delay after resetting the device before attempting to
do config cycles on it. Not waiting causes system hangs on some
chipsets, e.g. Intel E7520, when the driver is loaded.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
> >> Looks like memset() is zeroing wrong nr of bytes.
> >
> > Good catch, however, I think we can just remove this memset altogether
> > since the memory gets allocated via kzalloc.
>
> Correct, that memset() is superfluous.
Ok. Then this should do it.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
drivers/net/ibmveth.c | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use shorter method to determine whether adapter has configured ports
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sis190 driver assumes to find ISA only on SiS965.
similar fix is in sis900 driver, see bug report
http://bugs.debian.org/435547
Signed-off-by: maximilian attems <max@stro.at>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
use the simpler spin_trylock_irqsave() API to get the adapter lock.
[ this is also a fix for -rt where adapter->lock is a sleeping lock. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
SH boards in general only wire this up in 8 or 16-bit mode, and
as we never had the wrappers for 32-bit mode defined, SMC_CAN_USE_32BIT
caused build failure for the non-Solution Engine boards. This gets it
building again.
Also kill off the straggling set_irq_type() definition, this is left
over cruft that was missed when the rest of it switched to IRQ flags.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
--
drivers/net/smc91x.h | 4 +---
1 file changed, 1 insertion(+), 3 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Theory : though needless, it should not have hurt.
Practice: it does not play nice with DEBUG_SHIRQ + LOCKDEP + UP
(see https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=242572).
The patch makes sense in itself but I should dig why it has an effect
on #242572 (assuming that NAPI do not change in a near future).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Fix extracted from Realtek's driver (8.002.00/20070713) for the PHY
attached to 8111/8168b chipsets.
The check against mac_version is just usual paranoia during the bugfix
period of the kernel cycle. -- FR
Tested on Asus M2A-VM motherboard by Roger So.
No regression on my Asrock 945G DVI either (built-in 8168 + 2x8169).
Signed-off-by: Roger So <roger.so@gmail.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
While filling the control set the driver tests for a PSPOLL frame.
But it tested only the subtype of the packet. The full type needs
to be tested to identify those packets reliably.
[dsd@gentoo.org: backport to mainline]
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
conf->mac_addr is not guaranteed to be set. This ensures priv->hwaddr is
always set to a valid mac address. Thanks to Johannes Berg
<johannes@sipsolutions.net> for finding this problem.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 77548f5807.
David Woodhouse wrote:
>This broke my shinybook. I seem to get absolutely _no_ outgoing packets,
>although I can receive OK.
Larry Finger wrote:
>Please revert this patch.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The device would not resume properly if it was shutdown before the system
was suspended. In such scenario where the netif_running state is 0,
bnx2_suspend() would not save the PCI state and so the memory enable bit
and bus master enable bit would be lost.
We fix this by always saving and restoring the PCI state in
bnx2_suspend() and bnx2_resume() regardless of netif_running() state.
Update version to 1.6.4.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joachim Deguara <joachim.deguara@amd.com> reported that tg3 devices
would not resume properly if the device was shutdown before the system
was suspended. In such scenario where the netif_running state is 0,
tg3_suspend() would not save the PCI state and so the memory enable bit
and bus master enable bit would be lost.
We fix this by always saving and restoring the PCI state in
tg3_suspend() and tg3_resume() regardless of netif_running() state.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* wrong argument passed to pci_unmap_single() on failure
exit paths
* leak in the same area
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is needed because commit 313674afa8
inlines the generic function to the caller.
Signed-off-by: Jan Altenberg <jan.altenberg@linutronix.de>
Signed-off-by: Li Yang <leoli@freescale.com>
This fix section mismatch:
reference to .exit.text:uec_mdio_exit (between 'ucc_geth_init' and 'uec_mdio_init')
void __exit uec_mdio_exit(void) is called from
- static int __init ucc_geth_init(void)
- static void __exit ucc_geth_exit(void)
First one would make error path more than just an error.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Li Yang <leoli@freescale.com>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (41 commits)
[RTNETLINK]: Fix warning for !CONFIG_KMOD
[IPV4] ip_options.c: kmalloc + memset conversion to kzalloc
[DECNET]: kmalloc + memset conversion to kzalloc
[NET]: ethtool_perm_addr only has one implementation
[NET]: ethtool ops are the only way
[PPPOE]: Improve hashing function in hash_item().
[XFRM]: State selection update to use inner addresses.
[IPSEC]: Ensure that state inner family is set
[TCP]: Bidir flow must not disregard SACK blocks for lost marking
[TCP]: Fix ratehalving with bidirectional flows
[PPPOL2TP]: Add CONFIG_INET Kconfig dependency.
[NET]: Page offsets and lengths need to be __u32.
[AF_UNIX]: Make code static.
[NETFILTER]: Make nf_ct_ipv6_skip_exthdr() static.
[PKTGEN]: make get_ipsec_sa() static and non-inline
[PPPoE]: move lock_sock() in pppoe_sendmsg() to the right location
[PPPoX/E]: return ENOTTY on unknown ioctl requests
[IPV6]: ipv6_addr_type() doesn't know about RFC4193 addresses.
[NET]: Fix prio_tune() handling of root qdisc.
[NET]: Fix sch_api to properly set sch->parent on the root.
...
One patch for two trivial typos of 'error' with three R's, appearing in message strings.
There's a bunch more of the same in comments, not dealt with here.
Signed-off-by: Eddy L O Jansson <eddy@klopper.net>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rcu_dereference() primitive needs to be applied to an l-value in order to
ensure that compiler writers don't get an opportunity to apply reordering
optimizations that could result in multiple fetches or in other misbehavior.
This patch pulls the rcu_dereference() calls in bpq_seq_next() up to the point
at which the fetched pointers are still l-values, rather than after
list_entry() has transformed them into r-values.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All drivers implement ethtool get_perm_addr the same way -- by calling
the generic function. So we can inline the generic function into the
caller and avoid going through the drivers.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the transition to the ethtool_ops way of doing things, we supported
calling the device's ->do_ioctl method to allow unconverted drivers to
continue working. Those days are long behind us, all in-tree drivers
use the ethtool_ops way, and so we no longer need to support this.
The bonding driver is the biggest beneficiary of this; it no longer
needs to call ioctl() as a fallback if ethtool_ops aren't supported.
Also put a proper copyright statement on ethtool.c.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new code produces the same results as the old version and is
~ 3 to 6 times faster for 4-bit hashes on the CPUs I tested.
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPPOL2TP uses UDP so it obviously depends on CONFIG_INET.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
and the last one for now: Acquire the sock lock in pppoe_sendmsg()
before accessing the sock - and in particular avoid releasing the lock
even though it hasn't been acquired.
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
here another patch for the PPPoX/E code that makes sure that ENOTTY is
returned for unknown ioctl requests rather than 0 (and removes another
unneeded initializer which I didn't bother creating a separate patch for).
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because IPv4 and IPv6 both depend on the presence of the loopback
device to function, failure in registration the loopback device should
be fatal.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver was still using the deprecated prom_*() interfaces to
obtain values out of the OBP device tree, and this is causing
some kinds of problems on sparc32 especially SMP boxes.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
Fix a potential NULL pointer dereference in mace_interrupt() in drivers/net/pcmcia/nmclan_cs.c
PATCH kernel 2.6.22] PCMCIA-NETDEV : modify smc91c92_cs.c to become SMP safe
S2io: Increment received packet count correctly
S2io: Fix crash when resetting adapter
S2io: Mask spurious interrupts
S2IO: Implementing review comments from old patches
S2IO: Checking for the return value of pci map function
S2IO: Removing MSI support from driver
S2IO: Removing 3 buffer mode support from the driver
netxen: drop redudant spinlock
netxen: Fix interrupt handling for multiport adapters
netxen: re-init station address after h/w init
tulip: Remove tulip maintainer
forcedeth: mac address correct
gfar: Fix modpost warning
lib8390: comment on locking by Alan Cox
Fix a potential NULL pointer dereference in write_bulk_callback() in drivers/net/usb/pegasus.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ipath: Workaround problem of errormask register being overwritten
IB/ipath: Fix some issues with buffer cancel and sendctrl register update
IB/ipath: Use faster put_tid_2 routine after initialization
IB/ipath: Remove unsafe fastrcvint code from interrupt handler
IB/ehca: Move extern declarations from .c files to .h files
IB/mlx4: Whitespace fix
IB/ehca: Fix include order to better match kernel style
mlx4_core: Remove kfree() in mlx4_mr_alloc() error flow
RDMA/amso1100: Initialize the wait_queue_head_t in the c2_qp structure
This patch fixes a potential null dereference bug where we dereference
DEV before a null check. This patch simply moves the dereferencing after
the null check.
Signed-off-by: Micah Gruber <micah.gruber@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
protect smc_start_xmit, smc_interrupt and media_check by spin_lock.
Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Fix to increment the received packet count correctly.
(Resending; Removed HTML sections in the patch)
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Removed the call to pci_set_power_state to reset the adapter as it was resulting
in system crash on some platforms.
(Resending; Removed HTML sections in the patch)
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Mask single and double bit ETQ ecc errors to inhibit spurious interrupts.
(Resending; Removed HTML sections in the patch)
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Checking for the return value of pci map function
- Implemented Francois Romieu's comments on eliminating code duplication
using goto
- Implemented Francois Romieu's comments on using a temporary variable for
accessing statistics structure
Signed-off-by: Veena Parat <veena.parat@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Removed 3 buffer mode support from driver - unused feature
- Incorporated Jeff Garzik's comments on elimination of inline typecasting
- Code cleanup : Removed a few extra spaces
Signed-off-by: Veena Parat <veena.parat@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some leftover code that makes use of adapter->lock in tx_timeout function,
which resets the interface under this lock. In close() when the workqueue
is flushed, prints the warning about sleeping with interrupts disabled
(when spinlock debug is enabled). The lock was required with private netxen
IOCTLs, which were removed a while ago.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes masking of interrupts on multiport adapters. Also disables
interrupts upon ifdown interface. The wrong mask could result in interrupt
flood after interface is down.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a workaround for firmware bug with 2nd port of multiport adapter,
where MAC address is reset. Driver just needs to overwrite it with the
value read from PROM.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In older chipsets, the mac address was stored in reversed order.
However, in newer chipsets, the mac address is in correct order. This
patch takes those newer chipsets into account and does not rely on a
special bit setup by BIOS'.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix the following modpost warning:
WARNING: vmlinux.o(.init.text+0x1aa6c): Section mismatch: reference to .exit.text:gfar_mdio_exit (between 'gfar_init' and 'gfar_mdio_init')
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Additional explanation of problems with locking by Alan Cox.
Signed-off-by: Jarek Poplawski <jarkao2@o2.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes a potential null dereference bug where we dereference
pegasus before a null check. This patch simply moves the dereferencing
after the null check.
Signed-off-by: Micah Gruber <micah.gruber@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Added code to recognize the second interface on M5275 boards.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On the MCF5272, there is no need to read the ICR before writing it :
the bit 4n+3 is a write-enable for the bits 4n,4n+1 and 4n+2.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the work queue code in the FEC driver.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Removed unused CONFIG symbol and its conditional code from FEC driver.
Pointed out by Robert P. J. Day <rpjday@mindspring.com>.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Include cacheflush.h to get definitions for cache functions used
in this code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Gabriel C reports lguest doesn't compile with CONFIG_BLOCK=n. Fix this
by introducing a config var for the block device, which depends on
LGUEST && BLOCK. Do the same for the net driver, rather then depending
gratuitously on CONFIG_NET.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Gabriel C <nix.or.die@googlemail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Input Serio: Blackfin doesnt support I8042 - make sure it doesnt get selected
Blackfin arch: add BF54x I2C/TWI TWI0 driver support
Blackfin On-Chip RTC driver update for supporting BF54x
Blackfin Ethernet MAC driver: fix bug Report returned -ENOMEM upwards (in case L1/uncached memory alloc fails)
Blackfin arch: add error message when IRQ no available
Blackfin arch: Initialize the exception vectors early in the boot process
Blackfin arch: fix a compiling warning about dma-mapping
Blackfin arch: switch to using proper defines this time THREAD_SIZE and PAGE_SIZE instead of just PAGE_SIZE everywhere
Blackfin arch: fix bug which unaligns the init thread's stack and causes the current macro to fail.
Blackfin arch: Load P0 before storing through it
Blackfin arch: fix KGDB bug, dont forget last parameter.
Blackfin arch: add selections for BF544 and BF542
Blackfin arch: use bfin_read_SWRST() now that BF561 provides it
Blackfin arch: setup aliases for some core Core A MMRs
mlx4_mr_alloc() doesn't actually allocate mr (it just initializes the
pointer that the caller passes in), so it shouldn't free it if an
error occurs.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change INT0 trigger mode from edge-sense mode to level-sense mode,
in order to fix the following timeout error:
'NETDEV WATCHDOG: eth0: transmit timed out'.
This patch is required only for the Mappi platform.
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Cc: Hitoshi Yamamoto <hitoshiy@linux-m32r.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Documentation: The FIXMEs
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Documentation: The Drivers
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Address of auto variable is not a userland pointer. A good thing, too,
since if pppol2tp_tunnel_getsockopt() would _really_ get a userland pointer
as argument, it would be an instant roothole...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
netdev: i82596 Ethernet needs <asm/cacheflush.h> on m68k
drivers/net/82596.c: In function 'init_rx_bufs':
drivers/net/82596.c:552: error: implicit declaration of function 'cache_clear'
drivers/net/82596.c: In function 'i596_start_xmit':
drivers/net/82596.c:1104: error: implicit declaration of function 'cache_push'
The driver still compiles on ia32 (CONFIG_APRICOT=y)
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch contains new device settings for MCP73 chipset.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Sparse (correctly) thinks this function should be static. Make it so.
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Coverity checker noted that we've already dereferenced "dev" when we
check whether it's NULL.
Since it's impossible that "dev" is NULL at this place this patch
removes the NULL check.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a change to remove a local hack in favour to __maybe_unused that
has been recently added.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
phy_read() returns a negative number if there's an error, but the
error-checking code in the Vitesse driver's config_intr function
triggers if phy_read() returns non-zero. Correct that.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reduced allocation size for rx skb buffers, from 2308 bytes to
1356 per buffer.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use constants already provided by the kernel for ethernet related lengths.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change the threshold number of descriptors used to trigger CMB writes.
The vendor reports that under certain conditions this will reduce the
number of unnecessary tx interrupts and improve rx performance.
This change is lifted directly from vendor version 1.2.40.2 of the L1
driver.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The DMA engine setup contains a typo that can result in an incorrect
dmaw_block setting.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fixed rare issue that 'lv1_net_start_rx_dma failed, status=-9" was shown
in dmesg. This meant restarting rx DMA had been rejected by the hypervisor.
This issue would caused if the guest os requested starting DMA when
the hypervisor thought the DMA was in progress.
The state machine for DMA status of the hypervisor would be updated
by processing interrupt in the hypervisor.
Thus we should wait for the interrupt delivery before restarting
DMA.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Removed use of netif_poll_enable() in open function.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use net_device name for registration of irq as many network drivers do.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Removed the statistics information from private structre.
Instead, use net_device_stats in net_device structure.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
gelic: TX descriptor handling cleanup
- Emitted return value of NETDEV_TX_LOCKED when DMA map or kick
failure.
Now it would free the skb, update drop packet statistics
and return OK. Requested from Jeff Garzik.
- Enable tx queue if number of free descriptors are more than 2
- Fixed descriptor leak if dma map for second descriptor failed
- Stopped calling xmit handler from interrupt handler in order
to recheck tx queue. Instead, call appropriate helper functions.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Removed the embarrassing definition which was used in only one
place.
- Fixed wrong initialization of dmac_cmd_status.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fixed the bug that calculation of the address of rx descriptor was
wrong.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The firmware should be loaded after resetting hardware during PCI probe,
besides module unload. This fixes issue with 2nd port of multiport adapter
on powerpc blades. This patch also fixes a bug that PCI resources are not
freed if dma watchdog shutdown failed. The dma watchdog poll messages
during module unload are also suppressed.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Milan Bag <mbag@netxen.com>
Signed-off-by: Wen Xiong <wenxiong@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Adds netif message level control to the ucc_geth driver. The level can
be set by module parameter and ethtool.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The patch enables statistics in ucc_geth and adds ethtool support to
ucc_geth driver.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Support small QP queues
IB/ehca: Make internal_create/destroy_qp() static
IB/ehca: Move ehca2ib_return_code() out of line
IB/ehca: Generate async event when SRQ limit reached
IB/ehca: Support large page MRs
IB/mlx4: Fix error path in create_qp_common()
mlx4_core: Change command token on timeout
IB/mthca: Change command token on timeout
IB/ipath: Remove ipath_layer dead code
IB/mlx4: Fix leaks in __mlx4_ib_modify_qp
Enabling drivers from "Devices > Networking" (in menuconfig), for
example SLIP and/or PLIP, throws link time errors when CONFIG_NET itself
is =n. Have CONFIG_NETDEVICES depend on CONFIG_NET.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EP7211 SIR driver was the only one left without a new SIR API port.
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FW command token is currently only updated on a command completion
event. This means that on command timeout, the same token will be
reused for new command, which results in a mess if the timed out
command *does* eventually complete.
This is the same change as the patch for mthca from Michael
S. Tsirkin <mst@dev.mellanox.co.il> that was just merged. It seems
sensible to avoid gratuitous differences in FW command processing
between mthca and mlx4.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Fix two year old bug in early bootup asm.
[SPARC64]: Update defconfig.
[SPARC64]: Fix log message type in vio_create_one().
[SPARC64]: Tweak assertions in sun4v_build_virq().
[SPARC64]: Tweak kernel log messages in power_probe().
[SPARC64]: Fix handling of multiple vdc-port nodes.
[SPARC64]: Fix device type matching in VIO's devspec_show().
[SPARC64]: Fix MODULE_DEVICE_TABLE() specification in VDC and VNET.
[SPARC]: Add sys_fallocate() entries.
[SPARC64]: Use orderly_poweroff().
Doing |= 1 << 19 to 16bit unsigned is not particulary useful;
that register is 32bit, unlike the ones dealt with in the rest of
function, so we need u32 variable here.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WARNING: drivers/built-in.o(.text+0x3fd54): Section mismatch: reference to .init.data: (between 'ether3_probe' and 'ether1_setmulticastlist')
WARNING: drivers/built-in.o(.text+0x40380): Section mismatch: reference to .init.data: (between 'ether1_probe' and 'ether1_interrupt')
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Lguest net driver
A simple net driver for lguest.
[akpm@linux-foundation.org: include fix]
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andi Kleen <ak@suse.de>
Cc: Jeff Garzik <jeff@garzik.org>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Transform some calls to kmalloc/memset to a single kzalloc (or kcalloc).
Here is a short excerpt of the semantic patch performing
this transformation:
@@
type T2;
expression x;
identifier f,fld;
expression E;
expression E1,E2;
expression e1,e2,e3,y;
statement S;
@@
x =
- kmalloc
+ kzalloc
(E1,E2)
... when != \(x->fld=E;\|y=f(...,x,...);\|f(...,x,...);\|x=E;\|while(...) S\|for(e1;e2;e3) S\)
- memset((T2)x,0,E1);
@@
expression E1,E2,E3;
@@
- kzalloc(E1 * E2,E3)
+ kcalloc(E1,E2,E3)
[akpm@linux-foundation.org: get kcalloc args the right way around]
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: Pierre Ossman <drzeus-list@drzeus.cx>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg KH <greg@kroah.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
unregister_chrdev() always returns 0. There is no need to check the return
value.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tina Yang <tina.yang@oracle.com> discovered an MSI related problem
when doing kdump. The problem is that the kexec kernel is booted
without going through system reset, and as a result, MSI may already
be enabled when tg3_init_one() is called. tg3_init_one() calls
pci_save_state() which will save the stale MSI state. Later on in
tg3_open(), we call pci_enable_msi() to reconfigure MSI on the chip
before we reset the chip. After chip reset, we call
pci_restore_state() which will put the stale MSI address/data back
onto the chip.
This is no longer a problem in the latest kernel because
pci_restore_state() has been changed to restore MSI state from
internal data structures which will guarantee restoring the proper
MSI state.
But I think we should still fix it. Our save and restore sequence
can still cause very subtle problems down the road. The fix is to
have our own functions save and restore precisely what we need. We
also change it to save and restore state inside tg3_chip_reset() in a
more straight forward way.
Thanks to Tina for helping to test and debug the problem.
[ Bump driver version and release date. -DaveM ]
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband: (29 commits)
IB/mthca: Simplify use of size0 in work request posting
IB/mthca: Factor out setting WQE UD segment entries
IB/mthca: Factor out setting WQE remote address and atomic segment entries
IB/mlx4: Factor out setting other WQE segments
IB/mlx4: Factor out setting WQE data segment entries
IB/mthca: Factor out setting WQE data segment entries
IB/mlx4: Return receive queue sizes for userspace QPs from query QP
IB/mlx4: Increase max outstanding RDMA reads as target
RDMA/cma: Remove local write permission from QP access flags
IB/mthca: Use uninitialized_var() for f0
IB/cm: Make internal function cm_get_ack_delay() static
IB/ipath: Remove ipath_get_user_pages_nocopy()
IB/ipath: Make a few functions static
mlx4_core: Reset device when internal error is detected
IB/iser: Make a couple of functions static
IB/mthca: Fix printk format used for firmware version in warning
IB/mthca: Schedule MSI support for removal
IB/ehca: Fix warnings issued by checkpatch.pl
IB/ehca: Restructure ehca_set_pagebuf()
IB/ehca: MR/MW structure refactoring
...
The driver didn't allow an interface's MAC address to be modified if the
respective interface wasn't setup - a failing Hcall was the result. Thus
bonding wasn't usable. The fix moves the failing Hcall which was registering
a MAC address for the reception of BC packets in firmware from the port up
and down functions to the port resources setup functions. Additionally the
missing update of the last_rx member of the netdev structure was added.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch implements the driver necessary use the Analog Devices
Blackfin processor's on-chip ethernet MAC controller.
[try#2]
- add timeout control
- kill dma_config_reg bitfields
- some trivial cleanup
[try#3]
- add endianess check
- add DRV_NAME, DRV_VERSION... driver information string
- add some comments for silicon anomaly and dma API confusion
- some code trivial cleanup
[try#4]
- add Blackfin latest GPIO pin mux opertion with Michael Hennerich's
help and Dan's review
- rewrite the DMA descriptor list operation in a more readable way
by Joe's review
[try#5]
- cleanup some coding style by Joe's review.
[try#6]
- 1.1 version fix a bug when set up multicast list pointed by Mr. yoshfuji
- rearrange the desc_list_free function.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The TSEC/eTSEC can detect the interface to the PHY automatically,
but it isn't able to detect whether the RGMII connection needs internal
delay. So we need to detect that change in the device tree, propagate
it to the platform data, and then check it if we're in RGMII. This fixes
a bug on the 8641D HPCN board where the Vitesse PHY doesn't use the delay
for RGMII.
Signed-off-by: Andy Fleming <afleming@freescale.com>
The Vitesse PHY on the 8641D needs to be set up with internal delay to
work in RGMII mode. So we add skew when it is set to RGMII_ID mode.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Haruki Dai <Dai.Haruki@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
The Vitesse 824x PHY doesn't allow an interrupt to be cleared if
the mask bit for that interrupt isn't set. This means that the PHY
Lib's order of handling interrupts (disable, then clear) breaks on this
PHY. However, clearing then disabling the interrupt opens up the code
for a silly race condition. So rather than change the PHY Lib, we change
the Vitesse driver so it always clears interrupts before disabling them.
Further, the ack function only clears the interrupt if interrupts are
enabled.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: Haiying Wang <Haiying.Wang@freescale.com>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (24 commits)
[NETFILTER]: xt_connlimit needs to depend on nf_conntrack
[NETFILTER]: ipt_iprange.h must #include <linux/types.h>
[IrDA]: Fix IrDA build failure
[ATM]: nicstar needs virt_to_bus
[NET]: move __dev_addr_discard adjacent to dev_addr_discard for readability
[NET]: merge dev_unicast_discard and dev_mc_discard into one
[NET]: move dev_mc_discard from dev_mcast.c to dev.c
[NETLINK]: negative groups in netlink_setsockopt
[PPPOL2TP]: Reset meta-data in xmit function
[PPPOL2TP]: Fix use-after-free
[PKT_SCHED]: Some typo fixes in net/sched/Kconfig
[XFRM]: Fix crash introduced by struct dst_entry reordering
[TCP]: remove unused argument to cong_avoid op
[ATM]: [idt77252] Rename CONFIG_ATM_IDT77252_SEND_IDLE to not resemble a Kconfig variable
[ATM]: [drivers] ioremap balanced with iounmap
[ATM]: [lanai] sram_test_word() must be __devinit
[ATM]: [nicstar] Replace C code with call to ARRAY_SIZE() macro.
[ATM]: Eliminate dead config variable CONFIG_BR2684_FAST_TRANS.
[ATM]: Replacing kmalloc/memset combination with kzalloc.
[NET]: gen_estimator deadlock fix
...
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Set vio->desc_buf to NULL after freeing.
[SPARC]: Mark sparc and sparc64 as not having virt_to_bus
[SPARC64]: Fix reset handling in VNET driver.
[SPARC64]: Handle reset events in vio_link_state_change().
[SPARC64]: Handle LDC resets properly in domain-services driver.
[SPARC64]: Massively simplify VIO device layer and support hot add/remove.
[SPARC64]: Simplify VNET probing.
[SPARC64]: Simplify VDC device probing.
[SPARC64]: Add basic infrastructure for MD add/remove notification.
The network device frontend driver allows the kernel to access network
devices exported exported by a virtual machine containing a physical
network device driver.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: Ian Pratt <ian.pratt@xensource.com>
Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Keir Fraser <Keir.Fraser@cl.cam.ac.uk>
Cc: netdev@vger.kernel.org
Rather than using a tri-state integer for the wait flag in
call_usermodehelper_exec, define a proper enum, and use that. I've
preserved the integer values so that any callers I've missed should
still work OK.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Joel Becker <joel.becker@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Srivatsa Vaddagiri <vatsa@in.ibm.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: David Howells <dhowells@redhat.com>
Reset netfilter data and IP CB, fix dst_entry leak.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't use skb->len after passing it to ip_queue_xmit.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change all stats related magic numbers to constants.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The management firmware may still be loading during bnx2_init_one()
because of the D3hot -> D0 transition and the firmware version may
not be available without waiting a bit.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NVRAM interface is slightly modified on the 5709. To properly
support it, we need to change the buffered flag in the flash data
structure into multiple flags to indicate buffered operation, address
translation, and the use of write enable (WREN). The 5709 flash
only requires the buffered operation bit to be set.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In vnet_event(), if the channel was reset, try to get the link
going again by invoking vio_port_up() after dropping the lock.
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the maximum number of outstanding RDMA reads allowed as a
target from 4 to 16 to per QP. This allows RDMA read operations to
pipeline better.
Pointed out by Dotan Barak and Sagi Rotem.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Tested by David Santinoli
zd1211b chip 129b:1667 v4810 high 00-01-e3 AL2230S_RF pa0 ---N-
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the ID for Planex GW-US54GXS USB wireless adapter sold in
Japan.
Since this device returns the regulatory region as 0x49,
the patch 'Allow channels 1-11 for unrecognised regulatory domains' is
required.
Tested by Masakazu Mokuno
zd1211b chip 2019:5303 v4810 high 00-90-cc AL2230_RF pa0 ---N-
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The power mode can only be set 0~5 to firmware. Otherwise there will be a
firmware error generated. This patch fixed the invalid power mode requested
by driver.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwpriv <iface> set_power [0~6] can be used for ipw2100. '0' indicates
off and '6' indicates auto. 1~5 are the actual power levels.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reset the device when an internal error is detected.
Also, detect errors by polling the error buffer rather than using
interrupts. This is more robust and doesn't depend on MSI-X. Remove
the old interrupt handler entirely, since we don't want to support two
mechanisms for detecting internal errors.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Mark variables in drivers/* with uninitialized_var() if such a warning
appears, and analysis proves that the var is initialized properly on all
paths it is used.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The warning
drivers/net/wan/pc300_drv.c: In function ‘cpc_open’:
drivers/net/wan/pc300_drv.c:2942: warning: ‘br’ may be used
uninitialized in this function
was valid. Ensure 'br' is initialized in all cases.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This episode illustrates how an overused warning can train people to
ignore that warning, which winds up hiding bugs.
The warning
drivers/net/natsemi.c: In function ‘natsemi_remove1’:
drivers/net/natsemi.c:3222: warning: ignoring return value of
‘device_create_file’, declared with attribute warn_unused_result
is oft-ignored, even though at close inspection one notices this occurs
in the /remove/ function, not normally where creation occurs. A quick
s/create/remove/ and we are fixed, with the warning gone.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
