The function l2cap_get_conf_opt will return L2CAP_CONF_OPT_SIZE + opt->len
as length value. The opt->len however is in control over the remote user
and can be used by an attacker to gain access beyond the bounds of the
actual packet.
To prevent any potential leak of heap memory, it is enough to check that
the resulting len calculation after calling l2cap_get_conf_opt is not
below zero. A well formed packet will always return >= 0 here and will
end with the length value being zero after the last option has been
parsed. In case of malformed packets messing with the opt->len field the
length value will become negative. If that is the case, then just abort
and ignore the option.
In case an attacker uses a too short opt->len value, then garbage will
be parsed, but that is protected by the unknown option handling and also
the option parameter size checks.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When doing option parsing for standard type values of 1, 2 or 4 octets,
the value is converted directly into a variable instead of a pointer. To
avoid being tricked into being a pointer, check that for these option
types that sizes actually match. In L2CAP every option is fixed size and
thus it is prudent anyway to ensure that the remote side sends us the
right option size along with option paramters.
If the option size is not matching the option type, then that option is
silently ignored. It is a protocol violation and instead of trying to
give the remote attacker any further hints just pretend that option is
not present and proceed with the default values. Implementation
following the specification and its qualification procedures will always
use the correct size and thus not being impacted here.
To keep the code readable and consistent accross all options, a few
cosmetic changes were also required.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
I can't see that these drivers use the old GPIO inlcudes in any
way, drop <linux/gpio.h> and <linux/of_gpio.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With commit e163376220 ("Bluetooth: Handle bt_accept_enqueue() socket
atomically") lock_sock[_nested]() is used to acquire the socket lock
before manipulating the socket. lock_sock[_nested]() may block, which
is problematic since bt_accept_enqueue() can be called in bottom half
context (e.g. from rfcomm_connect_ind()):
[<ffffff80080d81ec>] __might_sleep+0x4c/0x80
[<ffffff800876c7b0>] lock_sock_nested+0x24/0x58
[<ffffff8000d7c27c>] bt_accept_enqueue+0x48/0xd4 [bluetooth]
[<ffffff8000e67d8c>] rfcomm_connect_ind+0x190/0x218 [rfcomm]
Add a parameter to bt_accept_enqueue() to indicate whether the
function is called from BH context, and acquire the socket lock
with bh_lock_sock_nested() if that's the case.
Also adapt all callers of bt_accept_enqueue() to pass the new
parameter:
- l2cap_sock_new_connection_cb()
- uses lock_sock() to lock the parent socket => process context
- rfcomm_connect_ind()
- acquires the parent socket lock with bh_lock_sock() => BH
context
- __sco_chan_add()
- called from sco_chan_add(), which is called from sco_connect().
parent is NULL, hence bt_accept_enqueue() isn't called in this
code path and we can ignore it
- also called from sco_conn_ready(). uses bh_lock_sock() to acquire
the parent lock => BH context
Fixes: e163376220 ("Bluetooth: Handle bt_accept_enqueue() socket atomically")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
This patch adds support for 8977 chipset to mwifiex with SDIO
interface. Register offsets and supported feature flags are
updated. Firmware image used will be mrvl/sd8977_uapsta.bin.
Signed-off-by: Hemantkumar Suthar <shemant@marvell.com>
Signed-off-by: Rakesh Parmar <rakeshp@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
h4_recv_buf() callers store the return value to socket buffer and
recursively pass the buffer to h4_recv_buf() without protection. So,
ERR_PTR returned from h4_recv_buf() can be dereferenced, if called again
before setting the socket buffer to NULL from previous error. Check if
skb is ERR_PTR in h4_recv_buf().
Reported-by: syzbot+017a32f149406df32703@syzkaller.appspotmail.com
Signed-off-by: Myungho Jung <mhjungk@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The platform specific wake-up interrupt is optional. Don't print
an error message in case it is missing, merely inform the user in
this case.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use DEFINE_DEBUGFS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTRIBUTE
for debugfs files.
Semantic patch information:
Rationale: DEFINE_SIMPLE_ATTRIBUTE + debugfs_create_file()
imposes some significant overhead as compared to
DEFINE_DEBUGFS_ATTRIBUTE + debugfs_create_file_unsafe().
Generated by: scripts/coccinelle/api/debugfs/debugfs_simple_attr.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use DEFINE_DEBUGFS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTRIBUTE
for debugfs files.
Semantic patch information:
Rationale: DEFINE_SIMPLE_ATTRIBUTE + debugfs_create_file()
imposes some significant overhead as compared to
DEFINE_DEBUGFS_ATTRIBUTE + debugfs_create_file_unsafe().
Generated by: scripts/coccinelle/api/debugfs/debugfs_simple_attr.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch add qca_set_bdaddr() to set the device
address for latest Qualcomm Bluetooth chipset wcn3990 and above.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
- Fix console ramoops to show the previous boot logs (Sai Prakash Ranjan)
- Avoid allocation and leak of platform data
-----BEGIN PGP SIGNATURE-----
Comment: Kees Cook <kees@outflux.net>
iQJKBAABCgA0FiEEpcP2jyKd1g9yPm4TiXL039xtwCYFAlxE/QYWHGtlZXNjb29r
QGNocm9taXVtLm9yZwAKCRCJcvTf3G3AJsVXD/94pJsNHogOle3XnZJst/1cV4+R
KTyQ6QQ1184lI5FPGJliV3veCuKnTY4Q7e5vCl2mzEvds+VRxu2yUm+LFxKVj04W
yiRNv8Yn3+3eKxNufqLa9ySbsSZyIpoCKQ/20nbC5cNM3r+Gq12GUnDBixtGdl9V
fB316emIaKR70Qvi9KlfwDTcjh+SWBR2u8L0YsmTaoJkjtaCJhekN3hfya6Wnjf5
1sj1fCDzteda/Ld0gXoImHPvt0UcHPJDp1+ZhY0ja64QIuoWwDxsisp4X4nS8iFD
oak9BWRDhRwSzPnyCu8BI3Hc4ayxcBYR/vmBS12LTkIJVdR1CaqfeDYvZexyX04n
TYZnmPeZ+2R3wzA9aCLjUDEAYNi403sLqIvR99jlrOoiMo+5Bf05TvBG8lND2dQg
A13854vg9ssxfiuEmvxJTg8SLtcFiqEtrzZhqaLVfuf4cqaN3o0Ed+A0gjZadwwD
TPxiMh4YEZuw+qszZwyzi7uECKOvJIJeLCL8CApPvihCNFy2vKF5wj58ZizXXmoT
Orq6DJ1ITx4DTkYIgtiTC9HKDuvNDZ/ncdb5QoqlpoTe01r8GQOzffZ+tD3xRTNc
8+yAdK0/bTjLVNbFX/Q4dwagh0I8EQSrdw8CmmQs0lsCvfyYTfHz8uPeBQ7rrzeN
2r1H7a/OKpL/duTkEw==
=m6sX
-----END PGP SIGNATURE-----
Merge tag 'pstore-v5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull pstore fixes from Kees Cook:
- Fix console ramoops to show the previous boot logs (Sai Prakash
Ranjan)
- Avoid allocation and leak of platform data
* tag 'pstore-v5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
pstore/ram: Avoid allocation and leak of platform data
pstore/ram: Fix console ramoops to show the previous boot logs
Pull networking fixes from David Miller:
1) Fix endless loop in nf_tables, from Phil Sutter.
2) Fix cross namespace ip6_gre tunnel hash list corruption, from
Olivier Matz.
3) Don't be too strict in phy_start_aneg() otherwise we might not allow
restarting auto negotiation. From Heiner Kallweit.
4) Fix various KMSAN uninitialized value cases in tipc, from Ying Xue.
5) Memory leak in act_tunnel_key, from Davide Caratti.
6) Handle chip errata of mv88e6390 PHY, from Andrew Lunn.
7) Remove linear SKB assumption in fou/fou6, from Eric Dumazet.
8) Missing udplite rehash callbacks, from Alexey Kodanev.
9) Log dirty pages properly in vhost, from Jason Wang.
10) Use consume_skb() in neigh_probe() as this is a normal free not a
drop, from Yang Wei. Likewise in macvlan_process_broadcast().
11) Missing device_del() in mdiobus_register() error paths, from Thomas
Petazzoni.
12) Fix checksum handling of short packets in mlx5, from Cong Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (96 commits)
bpf: in __bpf_redirect_no_mac pull mac only if present
virtio_net: bulk free tx skbs
net: phy: phy driver features are mandatory
isdn: avm: Fix string plus integer warning from Clang
net/mlx5e: Fix cb_ident duplicate in indirect block register
net/mlx5e: Fix wrong (zero) TX drop counter indication for representor
net/mlx5e: Fix wrong error code return on FEC query failure
net/mlx5e: Force CHECKSUM_UNNECESSARY for short ethernet frames
tools: bpftool: Cleanup license mess
bpf: fix inner map masking to prevent oob under speculation
bpf: pull in pkt_sched.h header for tooling to fix bpftool build
selftests: forwarding: Add a test case for externally learned FDB entries
selftests: mlxsw: Test FDB offload indication
mlxsw: spectrum_switchdev: Do not treat static FDB entries as sticky
net: bridge: Mark FDB entries that were added by user as such
mlxsw: spectrum_fid: Update dummy FID index
mlxsw: pci: Return error on PCI reset timeout
mlxsw: pci: Increase PCI SW reset timeout
mlxsw: pci: Ring CQ's doorbell before RDQ's
MAINTAINERS: update email addresses of liquidio driver maintainers
...
Yue Hu noticed that when parsing device tree the allocated platform data
was never freed. Since it's not used beyond the function scope, this
switches to using a stack variable instead.
Reported-by: Yue Hu <huyue2@yulong.com>
Fixes: 35da60941e ("pstore/ram: add Device Tree bindings")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
GCC 9 reworks the way the references to the stack canary are
emitted, to prevent the value from being spilled to the stack
before the final comparison in the epilogue, defeating the
purpose, given that the spill slot is under control of the
attacker that we are protecting ourselves from.
Since our canary value address is obtained without accessing
memory (as opposed to pre-v7 code that will obtain it from a
literal pool), it is unlikely (although not guaranteed) that
the compiler will spill the canary value in the same way, so
let's just disable this improvement when building with GCC9+.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
The ARM per-task stack protector GCC plugin hits an assert in
the compiler in some case, due to the fact the the SP mask
expression is not sign-extended as it should be. So fix that.
Suggested-by: Kugan Vivekanandarajah <kugan.vivekanandarajah@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Ido Schimmel says:
====================
mlxsw: spectrum_router: Add GRE tunnel support for Spectrum-2
Nir says:
In Spectrum-2, HW implementation of layer 3 tunnels differs from
Spectrum-1 when it comes to the underlay routing table selection.
Spectrum-2 uses a dedicated RIF that points to the virtual router used
for forwarding the encapsulated packets, while Spectrum-1 explicitly
specifies the virtual router itself.
Patches #1 and #2 add additional fields in RITR - Router interface table
register and RTDP - Routing tunnel decap properties respectively, the
fields are required for the new underlay RIF needed for Spectrum-2.
Patches #3-4 allow different set of RIF operations per ASIC type. The
first patch splits the operations and the following patch sets RIF ops
according to ASIC type.
Patches #5-9 introduce small changes to existing code to allow existence
of a dedicated underlay RIF along with the underlay virtual router, and
to support that new type of RIF that has no device.
Patch #10 takes care of updating the tunnel decap properties egress
underlay RIF required for Spectrum-2.
Patch #11 adds the implementation of Spectrum-2 specific RIF operations
and essentially enables layer 3 GRE tunnels on Spectrum-2.
Finally patches #12-18 add tests for GRE IP-in-IP tunnels, both in flat
and hierarchical topologies.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
where an ikey/okey pair is set. This test is based on hierarchical topology
described in file ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
where a key is set. This test is based on hierarchical topology described
in file ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
based on hierarchical topology described in file ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
where an ikey/okey pair is set. This test is based on flat topology
described in file ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
where a key is set. This test is based on flat topology described in file
ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
based on flat topology described in file ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a library with helper functions, to be used in testing IP-in-IP and GRE
tunnels, both in flat and in hierarchical topologies.
The topologies used in this library cover the three scenarios of tunnels -
a tunel with no bound device, a tunnel with bound device in the same VRF
and a tunnel with a bound device in a different VRF.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum-2 GRE tunnel implementation requires a specific underlay RIF that
points to the virtual router used for forwarding the encapsulated packet.
Add Spectrum-2 specific loopback router interface creation methods which
may create or reuse the dedicated underlay RIF.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum-2 requires to specify the egress RIF when setting tunnel decap
properties. Add a method for accessing the underlay RIF index and then use
it when setting decap properties.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum-2 underlay RIF is merely an auxiliary RIF that points to the
virtual router used for encapsulated packets lookup. It exists only when
its overlay RIF exists but may be shared with other overlay RIFs.
Hence it is undesired to mark any device as related to it.
Therefore allow usage of NULL device when allocating RIF.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the sake of Spectrum-2 GRE support, as ul_vr_id field is reserved for
Spectrum-2, Change mlxsw_sp_ipip_lb_ul_vr_id() implementation not to use
the reserved field.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum-2 GRE tunnels underlay should be given not only the virtual router
information for an encapsulated packet lookup, but also an underlay RIF
object which belongs to a virtual router.
Therefore add ul_rif_id field in struct mlxsw_sp_rif_ipip_lb, to be used
later in Spectrum-2 underlay RIF implementation. This field complements
ul_vr_id field, already present and defined as reserved for Spectrum-2.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The presence of an allocated RIF in mlxsw_sp->router->rifs[rif_index] marks
that rif_index as taken.
Set the marking of a taken RIF to happen before calling ops->create in
order to allow creation of a GRE underlay RIF, which may be allocated and
created as part of an overlay RIF creation.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-2, the underlay routing table is pointed by an underlay router
interface in contrary to Spectrum where only an underlay virtual router
should be set. That makes the underlay virtual router field in RITR
reserved for Spectrum-2.
Change loopback RIF creation function to support the new underlay RIF
field, however leave this field reserved for Spectrum-1 updates.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set RIF ops array as member of mlxsw_sp in order to control which RIF
operations callbacks are called per ASIC type. This is needed to control
per ASIC handling of loopback RIF configurations.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split RIF ops array for Spectrum-1 and Spectrum-2 callbacks in order to
support different sets of operations for loopback RIF handling, as
underlying implementation differs between the ASICs.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-2 we need to specify the underlay egress router interface
when performing IP-in-IP and NVE packet decapsulation in the underlay
router.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fields relevant for Spectrum-2 Loopback IPinIP router interface
creation. Add additional Loopback RIF protocol value - Generic, used for
creation of an explicit underlay RIF, and also add a field named
underlay_rif used for specifying the underlay RIF of a tunnel.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fixes and cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcPTc7AAoJECgfDbjSjVRpOEgH/Ahdx7VMYJtFsdmoJKiwhB7M
jRRi9R903V9H87vl1BXy6dutHw+WONJtm6FSZ1ayNWlVmUmWS6vci+IUErr2uDrv
KSG+dJMQLlF7t1dnLRwlLazvGa4/58+u0J459uKPQ5ckqwV5wXPjUS5Z0xF3ldxM
Twz6vhYRGKCUc10YZm/WmsjlLROgaNtRya10PzAGVmXPzbCpvJfiojKWJER+Eigq
JxWynTCm/YvIk824Ls9cDBVkDvb8GPS3blVbFnusR+D3ktvX7vLDPOsErGn4umVS
nUm3/WiQALB9fKer+SsgcEGVh+fa06KIITK+IBblULmrAIT3CJdJp70UJBjfdTM=
=DCkE
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio/vhost fixes and cleanups from Michael Tsirkin:
"Fixes and cleanups all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost/scsi: Use copy_to_iter() to send control queue response
vhost: return EINVAL if iovecs size does not match the message size
virtio-balloon: tweak config_changed implementation
virtio: don't allocate vqs when names[i] = NULL
virtio_pci: use queue idx instead of array idx to set up the vq
virtio: document virtio_config_ops restrictions
virtio: fix virtio_config_ops description
-----BEGIN PGP SIGNATURE-----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=hGlM
-----END PGP SIGNATURE-----
Merge tag 'for-5.0-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"A handful of fixes (some of them in testing for a long time):
- fix some test failures regarding cleanup after transaction abort
- revert of a patch that could cause a deadlock
- delayed iput fixes, that can help in ENOSPC situation when there's
low space and a lot data to write"
* tag 'for-5.0-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: wakeup cleaner thread when adding delayed iput
btrfs: run delayed iputs before committing
btrfs: wait on ordered extents on abort cleanup
btrfs: handle delayed ref head accounting cleanup in abort
Revert "btrfs: balance dirty metadata pages in btrfs_finish_ordered_io"
- A fix for OPTIMIZER_HIDE_VAR
From Michael S. Tsirkin
-----BEGIN PGP SIGNATURE-----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=2ce7
-----END PGP SIGNATURE-----
mergetag object 99e309b6ed
type commit
tag clang-format-for-linus-v5.0-rc3
tagger Miguel Ojeda <miguel.ojeda.sandonis@gmail.com> 1547999145 +0100
clang-format changes:
- Update of the for_each macro list
From Jason Gunthorpe
-----BEGIN PGP SIGNATURE-----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=mM3e
-----END PGP SIGNATURE-----
Merge tags 'compiler-attributes-for-linus-v5.0-rc3' and 'clang-format-for-linus-v5.0-rc3' of git://github.com/ojeda/linux
Pull misc clang fixes from Miguel Ojeda:
- A fix for OPTIMIZER_HIDE_VAR from Michael S Tsirkin
- Update clang-format with the latest for_each macro list from Jason
Gunthorpe
* tag 'compiler-attributes-for-linus-v5.0-rc3' of git://github.com/ojeda/linux:
include/linux/compiler*.h: fix OPTIMIZER_HIDE_VAR
* tag 'clang-format-for-linus-v5.0-rc3' of git://github.com/ojeda/linux:
clang-format: Update .clang-format with the latest for_each macro list
If an input number x for int_sqrt64() has the highest bit set, then
fls64(x) is 64. (1UL << 64) is an overflow and breaks the algorithm.
Subtracting 1 is a better guess for the initial value of m anyway and
that's what also done in int_sqrt() implicitly [*].
[*] Note how int_sqrt() uses __fls() with two underscores, which already
returns the proper raw bit number.
In contrast, int_sqrt64() used fls64(), and that returns bit numbers
illogically starting at 1, because of error handling for the "no
bits set" case. Will points out that he bug probably is due to a
copy-and-paste error from the regular int_sqrt() case.
Signed-off-by: Florian La Roche <Florian.LaRoche@googlemail.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 594cc251fd ("make 'user_access_begin()' do 'access_ok()'")
makes the access_ok() check part of the user_access_begin() preceding a
series of 'unsafe' accesses. This has the desirable effect of ensuring
that all 'unsafe' accesses have been range-checked, without having to
pick through all of the callsites to verify whether the appropriate
checking has been made.
However, the consolidated range check does not inhibit speculation, so
it is still up to the caller to ensure that they are not susceptible to
any speculative side-channel attacks for user addresses that ultimately
fail the access_ok() check.
This is an oversight, so use __uaccess_begin_nospec() to ensure that
speculation is inhibited until the access_ok() check has passed.
Reported-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Fix broken kpti page-table rewrite in bizarre KASLR configuration
- Fix module loading with KASLR
- Remove redundant definition of ARCH_SLAB_MINALIGN
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAlxDkU8ACgkQt6xw3ITB
YzRSeggAsvhxwa0Yg61A/s3tuaSO+kb6U6QXCVZSBw5F6tn3TPm7txoLlq+kUFoq
gcQ5RFzoGaW27TQafWQHVWcwYVWHYAc4WqSLQBQDMDPRpA0WR7sx/WUaxPdBDHt1
qLYHTKs68oTCdHMbvugNQhvBEt9s0qAQzrBk4exPhTLxkeWYELK4F2SpSgxzJun/
K5Eg9qrl8XRCXO5TGyUT54MtZaF2utnopJOVupRpBpIjBrCY6BGSpZbWA6pcNlUr
hftyXYMB8B4VGtKWAZp8mive2PFbzH/cj/rmxWDQRl0JUfnLw3lqXyHO8fe1e8vJ
cZ6tW2shLhHzEM50OmAYnfaeTPqxcg==
=EjUI
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Three arm64 fixes for -rc3.
We've plugged a couple of nasty issues involving KASLR-enabled
kernels, and removed a redundant #define that was introduced as part
of the KHWASAN fixes from akpm at -rc2.
- Fix broken kpti page-table rewrite in bizarre KASLR configuration
- Fix module loading with KASLR
- Remove redundant definition of ARCH_SLAB_MINALIGN"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
kasan, arm64: remove redundant ARCH_SLAB_MINALIGN define
arm64: kaslr: ensure randomized quantities are clean to the PoC
arm64: kpti: Update arm64_kernel_use_ng_mappings() when forced on
Daniel Borkmann says:
====================
pull-request: bpf 2019-01-20
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a out-of-bounds access in __bpf_redirect_no_mac, from Willem.
2) Fix bpf_setsockopt to reset sock dst on SO_MARK changes, from Peter.
3) Fix map in map masking to prevent out-of-bounds access under
speculative execution, from Daniel.
4) Fix bpf_setsockopt's SO_MAX_PACING_RATE to support TCP internal
pacing, from Yuchung.
5) Fix json writer license in bpftool, from Thomas.
6) Fix AF_XDP to check if an actually queue exists during umem
setup, from Krzysztof.
7) Several fixes to BPF stackmap's build id handling. Another fix
for bpftool build to account for libbfd variations wrt linking
requirements, from Stanislav.
8) Fix BPF samples build with clang by working around missing asm
goto, from Yonghong.
9) Fix libbpf to retry program load on signal interrupt, from Lorenz.
10) Various minor compile warning fixes in BPF code, from Mathieu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzkaller was able to construct a packet of negative length by
redirecting from bpf_prog_test_run_skb with BPF_PROG_TYPE_LWT_XMIT:
BUG: KASAN: slab-out-of-bounds in memcpy include/linux/string.h:345 [inline]
BUG: KASAN: slab-out-of-bounds in skb_copy_from_linear_data include/linux/skbuff.h:3421 [inline]
BUG: KASAN: slab-out-of-bounds in __pskb_copy_fclone+0x2dd/0xeb0 net/core/skbuff.c:1395
Read of size 4294967282 at addr ffff8801d798009c by task syz-executor2/12942
kasan_report.cold.9+0x242/0x309 mm/kasan/report.c:412
check_memory_region_inline mm/kasan/kasan.c:260 [inline]
check_memory_region+0x13e/0x1b0 mm/kasan/kasan.c:267
memcpy+0x23/0x50 mm/kasan/kasan.c:302
memcpy include/linux/string.h:345 [inline]
skb_copy_from_linear_data include/linux/skbuff.h:3421 [inline]
__pskb_copy_fclone+0x2dd/0xeb0 net/core/skbuff.c:1395
__pskb_copy include/linux/skbuff.h:1053 [inline]
pskb_copy include/linux/skbuff.h:2904 [inline]
skb_realloc_headroom+0xe7/0x120 net/core/skbuff.c:1539
ipip6_tunnel_xmit net/ipv6/sit.c:965 [inline]
sit_tunnel_xmit+0xe1b/0x30d0 net/ipv6/sit.c:1029
__netdev_start_xmit include/linux/netdevice.h:4325 [inline]
netdev_start_xmit include/linux/netdevice.h:4334 [inline]
xmit_one net/core/dev.c:3219 [inline]
dev_hard_start_xmit+0x295/0xc90 net/core/dev.c:3235
__dev_queue_xmit+0x2f0d/0x3950 net/core/dev.c:3805
dev_queue_xmit+0x17/0x20 net/core/dev.c:3838
__bpf_tx_skb net/core/filter.c:2016 [inline]
__bpf_redirect_common net/core/filter.c:2054 [inline]
__bpf_redirect+0x5cf/0xb20 net/core/filter.c:2061
____bpf_clone_redirect net/core/filter.c:2094 [inline]
bpf_clone_redirect+0x2f6/0x490 net/core/filter.c:2066
bpf_prog_41f2bcae09cd4ac3+0xb25/0x1000
The generated test constructs a packet with mac header, network
header, skb->data pointing to network header and skb->len 0.
Redirecting to a sit0 through __bpf_redirect_no_mac pulls the
mac length, even though skb->data already is at skb->network_header.
bpf_prog_test_run_skb has already pulled it as LWT_XMIT !is_l2.
Update the offset calculation to pull only if skb->data differs
from skb->network_header, which is not true in this case.
The test itself can be run only from commit 1cf1cae963 ("bpf:
introduce BPF_PROG_TEST_RUN command"), but the same type of packets
with skb at network header could already be built from lwt xmit hooks,
so this fix is more relevant to that commit.
Also set the mac header on redirect from LWT_XMIT, as even after this
change to __bpf_redirect_no_mac that field is expected to be set, but
is not yet in ip_finish_output2.
Fixes: 3a0af8fd61 ("bpf: BPF for lightweight tunnel infrastructure")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Heiner Kallweit says:
====================
r8169: series with smaller improvements
Series with smaller improvements.
v2:
- fixed a small copy & paste error in patch 4
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl_init_one() is complex enough, so we better factor out getting the
ether_clk.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accessing the phy_device indirectly via the netdevice causes few issues:
- Accessing the phy_device when it's not attached may cause a NPE.
- If we have to access the phy_device when it's not attached we have
to use mdiobus_get_phy() to get a reference to the phy_device.
Therefore store a phy_device reference in struct rtl8169_private directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Triggering an asynchronous reset is problematic for the following
reasons, therefore reset the chip synchronously.
- The reset routine resets registers and parameters behind our back
what may collide with code executed after triggering the reset.
- __rtl8169_resume() is called as part of pm_runtime_get_sync() and
callers expect that the chip is fully resumed afterwards.
In context of this driver triggering an asynchonous reset should be
considered an emergency procedure.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
