We have macros in asm/asm.h to allow for use of the MOVN & MOVZ
instructions with compare-and-branch sequences providing compatibility
for ISA versions which don't include those instructions. However the
macros are unused, and appear to have always been unused. Delete the
dead code.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20909/
Cc: linux-mips@linux-mips.org
Improve performance for the relevant systems and remove the DMA ordering
barrier from `readX_relaxed' and `writeX_relaxed' MMIO accessors, where
it is not needed according to our requirements[1]. For consistency make
the same arrangement with low-level port I/O accessors, but do not
actually provide any accessors making use of it.
References:
[1] "LINUX KERNEL MEMORY BARRIERS", Documentation/memory-barriers.txt,
Section "KERNEL I/O BARRIER EFFECTS"
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20865/
Cc: Ralf Baechle <ralf@linux-mips.org>
Architecturally the MIPS ISA does not specify ordering requirements for
uncached bus accesses such as MMIO operations normally use and therefore
explicit barriers have to be inserted between MMIO accesses where
unspecified ordering of operations would cause unpredictable results.
For example the R2020 write buffer implements write gathering and
combining[1] and as used with the DECstation models 2100 and 3100 for
MMIO accesses it bypasses the read buffer entirely, because conflicts
are resolved by the memory controller for DRAM accesses only[2] (NB the
R2020 and R3020 buffers are the same except for the maximum clock rate).
Consequently if a device has say a 16-bit control register at offset 0,
a 16-bit event mask register at offset 2 and a 16-bit reset register at
offset 4, and the initial value of the control register is 0x1111, then
in the absence of barriers a hypothetical code sequence like this:
u16 init_dev(u16 __iomem *dev);
u16 x;
write16(dev + 2, 0xffff);
write16(dev + 0, 0x2222);
x = read16(dev + 0);
write16(dev + 1, 0x3333);
write16(dev + 0, 0x4444);
return x;
}
will return 0x1111 and issue a single 32-bit write of 0x33334444 (in the
little-endian bus configuration) to offset 0 on the system bus.
This is because the read to set `x' from offset 0 bypasses the write of
0x2222 that is still in the write buffer pending the completion of the
write of 0xffff to the reset register. Then the write of 0x3333 to the
event mask register is merged with the preceding write to the control
register as they share the same word address, making it a 32-bit write
of 0x33332222 to offset 0. Finally the write of 0x4444 to the control
register is combined with the outstanding 32-bit write of 0x33332222 to
offset 0, because, again, it shares the same address.
This is an example from a legacy system, given here because it is well
documented and affects a machine we actually support. But likewise
modern MIPS systems may implement weak MMIO ordering, possibly even
without having it clearly documented except for being compliant with the
architecture specification with respect to the currently defined SYNC
instruction variants[3].
Considering the above and that we are required to implement MMIO
accessors such that individual accesses made with them are strongly
ordered with respect to each other[4], add the necessary barriers to our
`inX', `outX', `readX' and `writeX' handlers, as well the associated
special use variants. It's up to platforms then to possibly define the
respective barriers so as to expand to nil if no ordering enforcement is
actually needed for a given system; SYNC is supposed to be as cheap as
a NOP on strongly ordered MIPS implementations though.
Retain the option to generate weakly-ordered accessors, so that the
arrangement for `war_io_reorder_wmb' is not lost in case we need it for
fully raw accessors in the future. The reason for this is that it is
unclear from commit 1e820da3c9 ("MIPS: Loongson-3: Introduce
CONFIG_LOONGSON3_ENHANCEMENT") and especially commit 8faca49a67
("MIPS: Modify core io.h macros to account for the Octeon Errata
Core-301.") why they are needed there under the previous assumption that
these accessors can be weakly ordered.
References:
[1] "LR3020 Write Buffer", LSI Logic Corporation, September 1988,
Section "Byte Gathering", pp. 6-7
[2] "DECstation 3100 Desktop Workstation Functional Specification",
Digital Equipment Corporation, Revision 1.3, August 28, 1990,
Section 6.1 "Processor", p. 4
[3] "MIPS Architecture For Programmers, Volume II-A: The MIPS32
Instruction Set Manual", Imagination Technologies LTD, Document
Number: MD00086, Revision 6.06, December 15, 2016, Table 5.5
"Encodings of the Bits[10:6] of the SYNC instruction; the SType
Field", p. 409
[4] "LINUX KERNEL MEMORY BARRIERS", Documentation/memory-barriers.txt,
Section "KERNEL I/O BARRIER EFFECTS"
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
References: 8faca49a67 ("MIPS: Modify core io.h macros to account for the Octeon Errata Core-301.")
References: 1e820da3c9 ("MIPS: Loongson-3: Introduce CONFIG_LOONGSON3_ENHANCEMENT")
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20864/
Cc: Ralf Baechle <ralf@linux-mips.org>
Redefine `mmiowb' in terms of `iobarrier_w' so that it works correctly
for MIPS I platforms, which have no SYNC machine instruction and use a
call to `wbflush' instead.
This doesn't change the semantics for CONFIG_CPU_CAVIUM_OCTEON, because
`iobarrier_w' expands to `wmb', which is ultimately the same as the
current arrangement. For MIPS I platforms this not only makes any code
that would happen to use `mmiowb' build and run, but it actually
enforces the ordering required as well, as `iobarrier_w' has it already
covered with the use of `wmb'.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20863/
Cc: Ralf Baechle <ralf@linux-mips.org>
Define MMIO ordering barriers as separate operations so as to allow
making places where such a barrier is required distinct from places
where a memory or a DMA barrier is needed.
Architecturally MIPS does not specify ordering requirements for uncached
bus accesses such as MMIO operations normally use and therefore explicit
barriers have to be inserted between MMIO accesses where unspecified
ordering of operations would cause unpredictable results.
MIPS MMIO ordering barriers are implemented using the same underlying
mechanism that memory or a DMA barrier ordering barriers use, that is
either a suitable SYNC instruction or a platform-specific `wbflush'
call. However platforms may implement different ordering rules for
different kinds of bus activity, so having a separate API makes it
possible to remove unnecessary barriers and avoid a performance hit they
may cause due to unrelated bus activity by making their implementation
expand to nil while keeping the necessary ones.
Also having distinct barriers for each kind of use makes it easier for
the reader to understand what code has been intended to do.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20862/
Cc: Ralf Baechle <ralf@linux-mips.org>
Rewrite to use the `reorder' assembly mode and remove manually scheduled
delay slots except where GAS cannot schedule a delay-slot instruction
due to a data dependency or a section switch (as is the case with the EX
macro). No change in machine code produced.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
[paul.burton@mips.com:
Fix conflict with commit 932afdeec1 ("MIPS: Add Kconfig variable for
CPUs with unaligned load/store instructions")]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20834/
Cc: Ralf Baechle <ralf@linux-mips.org>
Fix a commit 8a8158c85e ("MIPS: memset.S: EVA & fault support for
small_memset") regression and remove assembly warnings:
arch/mips/lib/memset.S: Assembler messages:
arch/mips/lib/memset.S:243: Warning: Macro instruction expanded into multiple instructions in a branch delay slot
triggering with the CPU_DADDI_WORKAROUNDS option set and this code:
PTR_SUBU a2, t1, a0
jr ra
PTR_ADDIU a2, 1
This is because with that option in place the DADDIU instruction, which
the PTR_ADDIU CPP macro expands to, becomes a GAS macro, which in turn
expands to an LI/DADDU (or actually ADDIU/DADDU) sequence:
13c: 01a4302f dsubu a2,t1,a0
140: 03e00008 jr ra
144: 24010001 li at,1
148: 00c1302d daddu a2,a2,at
...
Correct this by switching off the `noreorder' assembly mode and letting
GAS schedule this jump's delay slot, as there is nothing special about
it that would require manual scheduling. With this change in place
correct code is produced:
13c: 01a4302f dsubu a2,t1,a0
140: 24010001 li at,1
144: 03e00008 jr ra
148: 00c1302d daddu a2,a2,at
...
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 8a8158c85e ("MIPS: memset.S: EVA & fault support for small_memset")
Patchwork: https://patchwork.linux-mips.org/patch/20833/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: stable@vger.kernel.org # 4.17+
gcc 3.3 has been retired for a while, use PTRS_PER_PGD and remove the
asm-offsets.h inclusion.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20814/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
The crash utility initializes cpu state by reading the system kernel
memory, which is copied into vmcore.
It is also natural to preserve the online state for CPUs at crash.
Failing to do so could make the analysis tool present info for only 1 CPU
by default, and unable to find panic task.
Signed-off-by: Dengcheng Zhu <dzhu@wavecomp.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20809/
Cc: Paul Burton <pburton@wavecomp.com>
Cc: "ralf@linux-mips.org" <ralf@linux-mips.org>
Cc: "linux-mips@linux-mips.org" <linux-mips@linux-mips.org>
Cc: "rachel.mozes@intel.com" <rachel.mozes@intel.com>
In much the same vein as commit ac41f9c462 ("MIPS: Remove a temporary
hack for debugging cache flushes in SMTC configuration") and commit
eb75ecb113 ("MIPS: MT: Remove unused MT single-threaded cache flush
code"), remove the long obsolete ndflush & niflush command line
arguments which provided a hack that should not be useful outside of
debug sessions performed long ago.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Commit ac41f9c462 ("MIPS: Remove a temporary hack for debugging cache
flushes in SMTC configuration") removed an ugly hack that allowed cache
flushing to be performed single-threaded, something which should not be
necessary outside of debug sessions performed long ago.
Whilst the hack was removed from the cache flush code itself, the
mt_protdflush & mt_protiflush variables were left behind along with code
providing the protdflush & protiflush command line arguments. The
mt_cflush_lockdown() & mt_cflush_release() functions were also left
behind but are now entirely unused.
Remove all the unused code to complete the removal of the MT ASE
single-threaded cache flush hack.
Signed-off-by: Paul Burton <paul.burton@mips.com>
MIPSR6 CPUs do not support unaligned load/store instructions
(LWL, LWR, SWL, SWR and LDL, LDR, SDL, SDR for 64bit).
Currently the MIPS tree has some special cases to avoid these
instructions, and the code is testing for !CONFIG_CPU_MIPSR6.
This patch declares a new Kconfig variable:
CONFIG_CPU_HAS_LOAD_STORE_LR.
This variable indicates that the CPU supports these instructions.
Then, the patch does the following:
- Carefully selects this option on all CPUs except MIPSR6.
- Switches all the special cases to test for the new variable,
and inverts the logic:
'#ifndef CONFIG_CPU_MIPSR6' turns into
'#ifdef CONFIG_CPU_HAS_LOAD_STORE_LR'
and vice-versa.
Also, when this variable is NOT selected (e.g. MIPSR6),
CONFIG_GENERIC_CSUM will default to 'y', to compile generic
C checksum code (instead of special assembly code that uses the
unsupported instructions).
This commit should not affect any existing CPU, and is required
for future Lexra CPU support, that misses these instructions too.
Signed-off-by: Yasha Cherikovsky <yasha.che3@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20808/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
The ELF appended dtb can be accessed now via 'fw_passed_dtb'.
Since raw appended dtb is accessed via that variable too,
this now effectively allows to boot with CONFIG_MIPS_RAW_APPENDED_DTB=y
on Octeon.
Signed-off-by: Yasha Cherikovsky <yasha.che3@gmail.com>
[paul.burton@mips.com: Fix trivial __dtb_octeon_*_begin conflict]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20805/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Since commit 15f37e1588 ("MIPS: store the appended
dtb address in a variable"),
in kernels with MIPS_RAW_APPENDED_DTB=y, the early boot code detects
the dtb and stores it in the 'fw_passed_dtb' variable.
However, the dtb is not stored in 'fw_passed_dtb' in kernels with
MIPS_ELF_APPENDED_DTB=y.
Under MIPS_ELF_APPENDED_DTB=y, the dtb is also located in the
__appended_dtb section, so we just need to update the #ifdef.
This will allow to access the dtb in a more uniform way.
Fixes: 15f37e1588 ("MIPS: store the appended dtb address in a variable")
Signed-off-by: Yasha Cherikovsky <yasha.che3@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20803/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
It makes the code more readable, especially in the nested ifdefs.
Signed-off-by: Yasha Cherikovsky <yasha.che3@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20802/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Out-of-tree platforms may not be based on Generic as shown in customer
communication. Share the prepare method with all using UHI boot protocol,
and put into machine_kexec.c.
The benefit is that, when having kexec_args related problems, developers
will naturally look into machine_kexec.c, where "CONFIG_UHI_BOOT" will be
found, prompting them to add "select UHI_BOOT" to the platform Kconfig. It
would otherwise require a lot debugging or online searching to be aware
that the solution is in Generic code.
Tested-by: Rachel Mozes <rachel.mozes@intel.com>
Reported-by: Rachel Mozes <rachel.mozes@intel.com>
Signed-off-by: Dengcheng Zhu <dzhu@wavecomp.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20569/
Cc: pburton@wavecomp.com
Cc: ralf@linux-mips.org
Cc: linux-mips@linux-mips.org
We can rely on the system kernel and the dump capture kernel themselves in
memory usage.
Being restrictive with 512MB limit may cause kexec tool failure on some
platforms.
Tested-by: Rachel Mozes <rachel.mozes@intel.com>
Reported-by: Rachel Mozes <rachel.mozes@intel.com>
Signed-off-by: Dengcheng Zhu <dzhu@wavecomp.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20568/
Cc: pburton@wavecomp.com
Cc: ralf@linux-mips.org
Cc: linux-mips@linux-mips.org
The existing implementation lets machine_kexec() CPU jump to reboot code
buffer, whereas other CPUs to relocated_kexec_smp_wait. The natural way to
bring up an SMP new kernel would be to let CPU0 do it while others being
halted. For those failing to do so, fall back to the jumping method.
Signed-off-by: Dengcheng Zhu <dzhu@wavecomp.com>
[paul.burton@mips.com: Guard kexec_nonboot_cpu_jump with CONFIG_SMP]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20570/
Cc: pburton@wavecomp.com
Cc: ralf@linux-mips.org
Cc: linux-mips@linux-mips.org
Cc: rachel.mozes@intel.com
Original Loongson-3 pci_ops can only access standard pci config space,
this patch let it be able to access extended pci config space.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
[paul.burton@mips.com: Tweaks to fix checkpatch warnings, reverse xmas tree]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20707/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Huacai Chen <chenhuacai@gmail.com>
New Loongson-3 (Loongson-3A R2, Loongson-3A R3, and newer) has SFB
(Store Fill Buffer) which can improve the performance of memory access.
Now, SFB enablement is controlled by CONFIG_LOONGSON3_ENHANCEMENT, and
the generic kernel has no benefit from SFB (even it is running on a new
Loongson-3 machine). With this patch, we can enable SFB at runtime by
detecting the CPU type (the expense is war_io_reorder_wmb() will always
be a 'sync', which will hurt the performance of old Loongson-3).
[paul.burton@mips.com: Further info from Huacai:
In practise, I found that sometimes there are boot failures if I
enable SFB/LPA in cpu_probe(). I don't know why because processor
designers also haven't give me an explaination, but I think this may
have some relationships to speculative execution.]
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20426/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Huacai Chen <chenhuacai@gmail.com>
Call pcie_bus_configure_settings() on MIPS, like for other platforms.
The function pcie_bus_configure_settings() makes sure the MPS (Max
Payload Size) across the bus is uniform and provides the ability to
tune the MRSS (Max Read Request Size) and MPS (Max Payload Size) to
higher performance values. Some devices will not operate properly if
these aren't set correctly because the firmware doesn't always do it.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20649/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Huacai Chen <chenhuacai@gmail.com>
MIPS already has memblock support and all the memory is already registered
with it.
This patch replaces bootmem memory reservations with memblock ones and
removes the bootmem initialization.
Since memblock allocates memory in top-down mode, we ensure that memblock
limit is max_low_pfn to prevent allocations from the high memory.
To have the exceptions base in the lower 512M of the physical memory, its
allocation in arch/mips/kernel/traps.c::traps_init() is using bottom-up
mode.
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20560/
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-mm@kvack.org
Cc: linux-kernel@vger.kernel.org
Set the PCI controller of_node such that PCI devices can be
instantiated via device tree.
Signed-off-by: Tobias Wolf <dev-NTEO@vplace.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20423/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Enable the i2c controller on ocelot PCB123. While there are no i2c devices
on the board itself, it can be used to control the SFP transceivers.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20352/
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: linux-i2c@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Allan Nielsen <allan.nielsen@microchip.com>
Ocelot has an i2c controller, add it. There is only one possible pinmux
configuration so add it as well.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20353/
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: linux-i2c@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Allan Nielsen <allan.nielsen@microchip.com>
The comment describing arch_mem_init() was separated from the definition
of arch_mem_init() by commit a09fc446fb ("[MIPS] setup.c: use
early_param() for early command line parsing"). Move the comment such
that it's next to the definition again for ease of reading.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Clean up instances of casts to the type that a value already has, since
they are effectively no-ops and only serve to complicate the code.
This is the result of the following semantic patch:
@identitycast@
type T;
T *A;
@@
- (T *)(A)
+ A
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19599/
The rt3352 has a pin that can be used as second spi chip select,
watchdog reset or GPIO. The pinmux setup was missing the definition of
said pin.
The pin is configured via the same bit on rt5350, so reuse the existing
macro.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20301/
Cc: John Crispin <john@phrozen.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
arch/mips appears to have inherited SLOW_DOWN_IO from arch/x86 in
antiquity, but we never define CONF_SLOWDOWN_IO so this is unused code.
Perhaps it was once useful to keep the MIPS header close to the x86
version to ease comparisons or porting changes, but they've diverged
significantly at this point & x86 does this differently now anyway.
Delete the dead code.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20343/
Cc: linux-mips@linux-mips.org
MIPS has a copy of lib/iomap.c with minor alterations, none of which are
necessary given appropriate definitions of PIO_OFFSET, PIO_MASK &
PIO_RESERVED. Provide such definitions, select GENERIC_IOMAP & remove
arch/mips/lib/iomap.c to cut back on the needless duplication.
The one change this does make is to our mmio_{in,out}s[bwl] functions,
which began to deviate from their generic counterparts with commit
0845bb721e ("MIPS: iomap: Use __mem_{read,write}{b,w,l} for MMIO"). I
suspect that this commit was incorrect, and that the SEAD-3 platform
should have instead selected CONFIG_SWAP_IO_SPACE. Since the SEAD-3
platform code is now gone & the board is instead supported by the
generic platform (CONFIG_MIPS_GENERIC) which selects
CONFIG_SWAP_IO_SPACE anyway, this shouldn't be a problem any more.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20342/
Cc: linux-mips@linux-mips.org
For a long time arch/mips/Makefile used nm to discover the kernel entry
point by looking for the address of the kernel_entry symbol. This
doesn't work for systems which make use of bit 0 of the PC to reflect
the ISA mode - ie. microMIPS (and MIPS16, but we don't support building
kernels that target MIPS16 anyway).
So for a while with commit 5fc9484f5e ("MIPS: Set ISA bit in entry-y
for microMIPS kernels") we manually modified the last nibble of the
output from nm, which worked but wasn't particularly pretty.
Commit 27c524d174 ("MIPS: Use the entry point from the ELF file
header") then cleaned this up by using objdump to print the ELF entry
point which includes the ISA bit, rather than using nm to print the
address of the kernel_entry symbol which doesn't. That removed the ugly
replacement of the last nibble, but added its own ugliness by needing to
manually sign extend in the 32 bit case.
Unfortunately it has been pointed out that objdump's output is
localised, and therefore grepping for its "start address" output doesn't
work when the user's language settings are such that objdump doesn't
print in English.
We could simply revert commit 27c524d174 ("MIPS: Use the entry point
from the ELF file header") and return to the manual replacement of the
last nibble of entry-y, but it seems that was found sufficiently
unpalatable to avoid. We could attempt to force the language used by
objdump by setting an environment variable such as LC_ALL, but that
seems fragile. Instead we add a small tool named elf-entry which simply
prints out the entry point of the kernel in the format we require.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reported-by: Philippe Reynes <philippe.reynes@softathome.com>
Tested-by: Philippe Reynes <philippe.reynes@softathome.com>
Fixes: 27c524d174 ("MIPS: Use the entry point from the ELF file header")
Patchwork: https://patchwork.linux-mips.org/patch/20322/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Setting GPIO 21 high seems to be required to enable power to USB ports
on the WNDR3400v3. As there is already similar code for WNR3500L,
make the existing USB power GPIO code generic and use that.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20259/
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20315/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: John Crispin <john@phrozen.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Split the common dma.c which shared by Loongson-2E and Loongson-2F,
since the code in 'common' directory is assumed be shared by all 64bit
Loongson platforms (but Loongson-3 doesn't use it now). By the way,
Loongson-2E and Loongson-2F have already dropped 32bit kernel support,
so CONFIG_64BIT isn't needed.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20302/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Huacai Chen <chenhuacai@gmail.com>
- add build_{menu,n,g,x}config targets for compile-testing Kconfig
- fix and improve recursive dependency detection in Kconfig
- fix parallel building of menuconfig/nconfig
- fix syntax error in clang-version.sh
- suppress distracting log from syncconfig
- remove obsolete "rpm" target
- remove VMLINUX_SYMBOL(_STR) macro entirely
- fix microblaze build with CONFIG_DYNAMIC_FTRACE
- move compiler test for dead code/data elimination to Kconfig
- rename well-known LDFLAGS variable to KBUILD_LDFLAGS
- misc fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Vsb2
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- add build_{menu,n,g,x}config targets for compile-testing Kconfig
- fix and improve recursive dependency detection in Kconfig
- fix parallel building of menuconfig/nconfig
- fix syntax error in clang-version.sh
- suppress distracting log from syncconfig
- remove obsolete "rpm" target
- remove VMLINUX_SYMBOL(_STR) macro entirely
- fix microblaze build with CONFIG_DYNAMIC_FTRACE
- move compiler test for dead code/data elimination to Kconfig
- rename well-known LDFLAGS variable to KBUILD_LDFLAGS
- misc fixes and cleanups
* tag 'kbuild-v4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: rename LDFLAGS to KBUILD_LDFLAGS
kbuild: pass LDFLAGS to recordmcount.pl
kbuild: test dead code/data elimination support in Kconfig
initramfs: move gen_initramfs_list.sh from scripts/ to usr/
vmlinux.lds.h: remove stale <linux/export.h> include
export.h: remove VMLINUX_SYMBOL() and VMLINUX_SYMBOL_STR()
Coccinelle: remove pci_alloc_consistent semantic to detect in zalloc-simple.cocci
kbuild: make sorting initramfs contents independent of locale
kbuild: remove "rpm" target, which is alias of "rpm-pkg"
kbuild: Fix LOADLIBES rename in Documentation/kbuild/makefiles.txt
kconfig: suppress "configuration written to .config" for syncconfig
kconfig: fix "Can't open ..." in parallel build
kbuild: Add a space after `!` to prevent parsing as file pattern
scripts: modpost: check memory allocation results
kconfig: improve the recursive dependency report
kconfig: report recursive dependency involving 'imply'
kconfig: error out when seeing recursive dependency
kconfig: add build-only configurator targets
scripts/dtc: consolidate include path options in Makefile
Commit a0f97e06a4 ("kbuild: enable 'make CFLAGS=...' to add
additional options to CC") renamed CFLAGS to KBUILD_CFLAGS.
Commit 222d394d30 ("kbuild: enable 'make AFLAGS=...' to add
additional options to AS") renamed AFLAGS to KBUILD_AFLAGS.
Commit 06c5040cdb ("kbuild: enable 'make CPPFLAGS=...' to add
additional options to CPP") renamed CPPFLAGS to KBUILD_CPPFLAGS.
For some reason, LDFLAGS was not renamed.
Using a well-known variable like LDFLAGS may result in accidental
override of the variable.
Kbuild generally uses KBUILD_ prefixed variables for the internally
appended options, so here is one more conversion to sanitize the
naming convention.
I did not touch Makefiles under tools/ since the tools build system
is a different world.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
- Fix microMIPS build failures by adding a .insn directive to the
barrier_before_unreachable() asm statement in order to convince the
toolchain that the asm statement is a valid branch target rather
than a bogus attempt to switch ISA.
- Clean up our declarations of TLB functions that we overwrite with
generated code in order to prevent the compiler making assumptions
about alignment that cause microMIPS kernels built with GCC 7 &
above to die early during boot.
- Fix up a regression for MIPS32 kernels which slipped into the main
MIPS pull for 4.19, causing CONFIG_32BIT=y kernels to contain
inappropriate MIPS64 instructions.
- Extend our existing workaround for MIPSr6 builds that end up using
the __multi3 intrinsic to GCC 7 & below, rather than just GCC 7.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCW37wVhUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN18iAD/ZO02rgkTgMG7NvZMtbOwflxe1aVz
YpAQzcOSz+CBxgUA/30ZwZm37hgMi3YWOJMSfmbuWKsYi+/vkcjwlfai7UUF
=oJFy
-----END PGP SIGNATURE-----
Merge tag 'mips_4.19_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
- Fix microMIPS build failures by adding a .insn directive to the
barrier_before_unreachable() asm statement in order to convince the
toolchain that the asm statement is a valid branch target rather
than a bogus attempt to switch ISA.
- Clean up our declarations of TLB functions that we overwrite with
generated code in order to prevent the compiler making assumptions
about alignment that cause microMIPS kernels built with GCC 7 &
above to die early during boot.
- Fix up a regression for MIPS32 kernels which slipped into the main
MIPS pull for 4.19, causing CONFIG_32BIT=y kernels to contain
inappropriate MIPS64 instructions.
- Extend our existing workaround for MIPSr6 builds that end up using
the __multi3 intrinsic to GCC 7 & below, rather than just GCC 7.
* tag 'mips_4.19_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: lib: Provide MIPS64r6 __multi3() for GCC < 7
MIPS: Workaround GCC __builtin_unreachable reordering bug
compiler.h: Allow arch-specific asm/compiler.h
MIPS: Avoid move psuedo-instruction whilst using MIPS_ISA_LEVEL
MIPS: Consistently declare TLB functions
MIPS: Export tlbmiss_handler_setup_pgd near its definition
Some versions of GCC suboptimally generate calls to the __multi3()
intrinsic for MIPS64r6 builds, resulting in link failures due to the
missing function:
LD vmlinux.o
MODPOST vmlinux.o
kernel/bpf/verifier.o: In function `kmalloc_array':
include/linux/slab.h:631: undefined reference to `__multi3'
fs/select.o: In function `kmalloc_array':
include/linux/slab.h:631: undefined reference to `__multi3'
...
We already have a workaround for this in which we provide the
instrinsic, but we do so selectively for GCC 7 only. Unfortunately the
issue occurs with older GCC versions too - it has been observed with
both GCC 5.4.0 & GCC 6.4.0.
MIPSr6 support was introduced in GCC 5, so all major GCC versions prior
to GCC 8 are affected and we extend our workaround accordingly to all
MIPS64r6 builds using GCC versions older than GCC 8.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reported-by: Vladimir Kondratiev <vladimir.kondratiev@intel.com>
Fixes: ebabcf17bc ("MIPS: Implement __multi3 for GCC7 MIPS64r6 builds")
Patchwork: https://patchwork.linux-mips.org/patch/20297/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # 4.15+
Some versions of GCC for the MIPS architecture suffer from a bug which
can lead to instructions from beyond an unreachable statement being
incorrectly reordered into earlier branch delay slots if the unreachable
statement is the only content of a case in a switch statement. This can
lead to seemingly random behaviour, such as invalid memory accesses from
incorrectly reordered loads or stores, and link failures on microMIPS
builds.
See this potential GCC fix for details:
https://gcc.gnu.org/ml/gcc-patches/2015-09/msg00360.html
Runtime problems resulting from this bug were initially observed using a
maltasmvp_defconfig v4.4 kernel built using GCC 4.9.2 (from a Codescape
SDK 2015.06-05 toolchain), with the result being an address exception
taken after log messages about the L1 caches (during probe of the L2
cache):
Initmem setup node 0 [mem 0x0000000080000000-0x000000009fffffff]
VPE topology {2,2} total 4
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 64kB, 4-way, PIPT, no aliases, linesize 32 bytes
<AdEL exception here>
This is early enough that the kernel exception vectors are not in use,
so any further output depends upon the bootloader. This is reproducible
in QEMU where no further output occurs - ie. the system hangs here.
Given the nature of the bug it may potentially be hit with differing
symptoms. The bug is known to affect GCC versions as recent as 7.3, and
it is unclear whether GCC 8 fixed it or just happens not to encounter
the bug in the testcase found at the link above due to differing
optimizations.
This bug can be worked around by placing a volatile asm statement, which
GCC is prevented from reordering past, prior to the
__builtin_unreachable call.
That was actually done already for other reasons by commit 173a3efd3e
("bug.h: work around GCC PR82365 in BUG()"), but creates problems for
microMIPS builds due to the lack of a .insn directive. The microMIPS ISA
allows for interlinking with regular MIPS32 code by repurposing bit 0 of
the program counter as an ISA mode bit. To switch modes one changes the
value of this bit in the PC. However typical branch instructions encode
their offsets as multiples of 2-byte instruction halfwords, which means
they cannot change ISA mode - this must be done using either an indirect
branch (a jump-register in MIPS terminology) or a dedicated jalx
instruction. In order to ensure that regular branches don't attempt to
target code in a different ISA which they can't actually switch to, the
linker will check that branch targets are code in the same ISA as the
branch.
Unfortunately our empty asm volatile statements don't qualify as code,
and the link for microMIPS builds fails with errors such as:
arch/mips/mm/dma-default.s:3265: Error: branch to a symbol in another ISA mode
arch/mips/mm/dma-default.s:5027: Error: branch to a symbol in another ISA mode
Resolve this by adding a .insn directive within the asm statement which
declares that what comes next is code. This may or may not be true,
since we don't really know what comes next, but as this code is in an
unreachable path anyway that doesn't matter since we won't execute it.
We do this in asm/compiler.h & select CONFIG_HAVE_ARCH_COMPILER_H in
order to have this included by linux/compiler_types.h after
linux/compiler-gcc.h. This will result in asm/compiler.h being included
in all C compilations via the -include linux/compiler_types.h argument
in c_flags, which should be harmless.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 173a3efd3e ("bug.h: work around GCC PR82365 in BUG()")
Patchwork: https://patchwork.linux-mips.org/patch/20270/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-mips@linux-mips.org
- Restructure of lockdep and latency tracers
This is the biggest change. Joel Fernandes restructured the hooks
from irqs and preemption disabling and enabling. He got rid of
a lot of the preprocessor #ifdef mess that they caused.
He turned both lockdep and the latency tracers to use trace events
inserted in the preempt/irqs disabling paths. But unfortunately,
these started to cause issues in corner cases. Thus, parts of the
code was reverted back to where lockde and the latency tracers
just get called directly (without using the trace events).
But because the original change cleaned up the code very nicely
we kept that, as well as the trace events for preempt and irqs
disabling, but they are limited to not being called in NMIs.
- Have trace events use SRCU for "rcu idle" calls. This was required
for the preempt/irqs off trace events. But it also had to not
allow them to be called in NMI context. Waiting till Paul makes
an NMI safe SRCU API.
- New notrace SRCU API to allow trace events to use SRCU.
- Addition of mcount-nop option support
- SPDX headers replacing GPL templates.
- Various other fixes and clean ups.
- Some fixes are marked for stable, but were not fully tested
before the merge window opened.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCW3ruhRQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qiM7AP47NhYdSnCFCRUJfrt6PovXmQtuCHt3
c3QMoGGdvzh9YAEAqcSXwh7uLhpHUp1LjMAPkXdZVwNddf4zJQ1zyxQ+EAU=
=vgEr
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
- Restructure of lockdep and latency tracers
This is the biggest change. Joel Fernandes restructured the hooks
from irqs and preemption disabling and enabling. He got rid of a lot
of the preprocessor #ifdef mess that they caused.
He turned both lockdep and the latency tracers to use trace events
inserted in the preempt/irqs disabling paths. But unfortunately,
these started to cause issues in corner cases. Thus, parts of the
code was reverted back to where lockdep and the latency tracers just
get called directly (without using the trace events). But because the
original change cleaned up the code very nicely we kept that, as well
as the trace events for preempt and irqs disabling, but they are
limited to not being called in NMIs.
- Have trace events use SRCU for "rcu idle" calls. This was required
for the preempt/irqs off trace events. But it also had to not allow
them to be called in NMI context. Waiting till Paul makes an NMI safe
SRCU API.
- New notrace SRCU API to allow trace events to use SRCU.
- Addition of mcount-nop option support
- SPDX headers replacing GPL templates.
- Various other fixes and clean ups.
- Some fixes are marked for stable, but were not fully tested before
the merge window opened.
* tag 'trace-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (44 commits)
tracing: Fix SPDX format headers to use C++ style comments
tracing: Add SPDX License format tags to tracing files
tracing: Add SPDX License format to bpf_trace.c
blktrace: Add SPDX License format header
s390/ftrace: Add -mfentry and -mnop-mcount support
tracing: Add -mcount-nop option support
tracing: Avoid calling cc-option -mrecord-mcount for every Makefile
tracing: Handle CC_FLAGS_FTRACE more accurately
Uprobe: Additional argument arch_uprobe to uprobe_write_opcode()
Uprobes: Simplify uprobe_register() body
tracepoints: Free early tracepoints after RCU is initialized
uprobes: Use synchronize_rcu() not synchronize_sched()
tracing: Fix synchronizing to event changes with tracepoint_synchronize_unregister()
ftrace: Remove unused pointer ftrace_swapper_pid
tracing: More reverting of "tracing: Centralize preemptirq tracepoints and unify their usage"
tracing/irqsoff: Handle preempt_count for different configs
tracing: Partial revert of "tracing: Centralize preemptirq tracepoints and unify their usage"
tracing: irqsoff: Account for additional preempt_disable
trace: Use rcu_dereference_raw for hooks from trace-event subsystem
tracing/kprobes: Fix within_notrace_func() to check only notrace functions
...
MIPS_ISA_LEVEL is always defined as the 64 bit ISA that is a compatible
superset of the ISA that the kernel build is targeting, and is used to
allow us to emit instructions that we may detect support for at runtime.
When we use a .set MIPS_ISA_LEVEL directive & are building a 32-bit
kernel, we therefore are temporarily allowing the assembler to generate
MIPS64 instructions. Using the move pseudo-instruction whilst this is
the case is problematic because the assembler is likely to emit a daddu
instruction which will generate a reserved instruction exception when
executed on a MIPS32 machine.
Unfortunately the combination of commit a0a5ac3ce8 ("MIPS: Fix delay
slot bug in `atomic*_sub_if_positive' for R10000_LLSC_WAR") and commit
4936084c2e ("MIPS: Cleanup R10000_LLSC_WAR logic in atomic.h") causes
us to do exactly this in atomic_sub_if_positive(), and the result is
MIPS64 daddu instructions in 32-bit kernels.
Fix this by using .set mips0 to restore the default ISA after the ll
instruction, and use .set MIPS_ISA_LEVEL again prior to the sc. This
ensures everything but the ll & sc are assembled using the default ISA
for the kernel build & the move pseudo-instruction is emitted as a
MIPS32 addu instruction.
We appear to have another pre-existing instance of the same issue in our
atomic_fetch_*_relaxed() functions, and fix that up too by moving our
.set move0 such that it occurs prior to use of the move
pseudo-instruction.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: a0a5ac3ce8 ("MIPS: Fix delay slot bug in `atomic*_sub_if_positive' for R10000_LLSC_WAR")
Fixes: 4936084c2e ("MIPS: Cleanup R10000_LLSC_WAR logic in atomic.h")
Patchwork: https://patchwork.linux-mips.org/patch/20253/
Cc: James Hogan <jhogan@kernel.org>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Use new return type vm_fault_t for fault handler. For now, this is just
documenting that the function returns a VM_FAULT value rather than an
errno. Once all instances are converted, vm_fault_t will become a
distinct type.
Ref-> commit 1c8f422059 ("mm: change return type to vm_fault_t")
In this patch all the caller of handle_mm_fault() are changed to return
vm_fault_t type.
Link: http://lkml.kernel.org/r/20180617084810.GA6730@jordon-HP-15-Notebook-PC
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: James Hogan <jhogan@kernel.org>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: David S. Miller <davem@davemloft.net>
Cc: Richard Weinberger <richard@nod.at>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Levin, Alexander (Sasha Levin)" <alexander.levin@verizon.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
"Highlights:
- Gustavo A. R. Silva keeps working on the implicit switch fallthru
changes.
- Support 802.11ax High-Efficiency wireless in cfg80211 et al, From
Luca Coelho.
- Re-enable ASPM in r8169, from Kai-Heng Feng.
- Add virtual XFRM interfaces, which avoids all of the limitations of
existing IPSEC tunnels. From Steffen Klassert.
- Convert GRO over to use a hash table, so that when we have many
flows active we don't traverse a long list during accumluation.
- Many new self tests for routing, TC, tunnels, etc. Too many
contributors to mention them all, but I'm really happy to keep
seeing this stuff.
- Hardware timestamping support for dpaa_eth/fsl-fman from Yangbo Lu.
- Lots of cleanups and fixes in L2TP code from Guillaume Nault.
- Add IPSEC offload support to netdevsim, from Shannon Nelson.
- Add support for slotting with non-uniform distribution to netem
packet scheduler, from Yousuk Seung.
- Add UDP GSO support to mlx5e, from Boris Pismenny.
- Support offloading of Team LAG in NFP, from John Hurley.
- Allow to configure TX queue selection based upon RX queue, from
Amritha Nambiar.
- Support ethtool ring size configuration in aquantia, from Anton
Mikaev.
- Support DSCP and flowlabel per-transport in SCTP, from Xin Long.
- Support list based batching and stack traversal of SKBs, this is
very exciting work. From Edward Cree.
- Busyloop optimizations in vhost_net, from Toshiaki Makita.
- Introduce the ETF qdisc, which allows time based transmissions. IGB
can offload this in hardware. From Vinicius Costa Gomes.
- Add parameter support to devlink, from Moshe Shemesh.
- Several multiplication and division optimizations for BPF JIT in
nfp driver, from Jiong Wang.
- Lots of prepatory work to make more of the packet scheduler layer
lockless, when possible, from Vlad Buslov.
- Add ACK filter and NAT awareness to sch_cake packet scheduler, from
Toke Høiland-Jørgensen.
- Support regions and region snapshots in devlink, from Alex Vesker.
- Allow to attach XDP programs to both HW and SW at the same time on
a given device, with initial support in nfp. From Jakub Kicinski.
- Add TLS RX offload and support in mlx5, from Ilya Lesokhin.
- Use PHYLIB in r8169 driver, from Heiner Kallweit.
- All sorts of changes to support Spectrum 2 in mlxsw driver, from
Ido Schimmel.
- PTP support in mv88e6xxx DSA driver, from Andrew Lunn.
- Make TCP_USER_TIMEOUT socket option more accurate, from Jon
Maxwell.
- Support for templates in packet scheduler classifier, from Jiri
Pirko.
- IPV6 support in RDS, from Ka-Cheong Poon.
- Native tproxy support in nf_tables, from Máté Eckl.
- Maintain IP fragment queue in an rbtree, but optimize properly for
in-order frags. From Peter Oskolkov.
- Improvde handling of ACKs on hole repairs, from Yuchung Cheng"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1996 commits)
bpf: test: fix spelling mistake "REUSEEPORT" -> "REUSEPORT"
hv/netvsc: Fix NULL dereference at single queue mode fallback
net: filter: mark expected switch fall-through
xen-netfront: fix warn message as irq device name has '/'
cxgb4: Add new T5 PCI device ids 0x50af and 0x50b0
net: dsa: mv88e6xxx: missing unlock on error path
rds: fix building with IPV6=m
inet/connection_sock: prefer _THIS_IP_ to current_text_addr
net: dsa: mv88e6xxx: bitwise vs logical bug
net: sock_diag: Fix spectre v1 gadget in __sock_diag_cmd()
ieee802154: hwsim: using right kind of iteration
net: hns3: Add vlan filter setting by ethtool command -K
net: hns3: Set tx ring' tc info when netdev is up
net: hns3: Remove tx ring BD len register in hns3_enet
net: hns3: Fix desc num set to default when setting channel
net: hns3: Fix for phy link issue when using marvell phy driver
net: hns3: Fix for information of phydev lost problem when down/up
net: hns3: Fix for command format parsing error in hclge_is_all_function_id_zero
net: hns3: Add support for serdes loopback selftest
bnxt_en: take coredump_record structure off stack
...
